FATEK IoT User Manual
FATEK IoT
FATEK IoT Cloud Service Manual
V1.7
2020/6/2
FATEK IoT User Manual
2
Catalog
Catalog ....................................................................................................................................... 2
Table Catalog ............................................................................................................................. 4
Figure Catalog ............................................................................................................................ 5
1. Summary ........................................................................................................................... 7
2. Application Introduction .................................................................................................. 9
3. Device Activation Process ............................................................................................... 11
3.1 FATEK IoT System Setting ...................................................................................... 11
3.2 iMonitor ................................................................................................................. 11
3.3 iAccess .................................................................................................................... 12
4. Website Management System ....................................................................................... 13
5. Management ................................................................................................................... 15
5.1 User Management ................................................................................................. 18
5.1.1 User List .................................................................................................... 18
5.1.2 Account Certification ................................................................................. 20
5.2 iMonitor Data Management ................................................................................. 21
5.2.1 iMonitor add device ................................................................................... 21
5.2.2 iMonitor add new dataitem ....................................................................... 23
5.2.3 iMonitor add new dataitem group .............................................................. 26
5.2.4 iMonitor add new trend ............................................................................. 27
5.3 iAccess Device Management................................................................................. 29
5.3.1 iAccess add device ..................................................................................... 29
5.3.2 iAccess add Dataitem Group ....................................................................... 31
5.3.3 iAccess add new dataitem .......................................................................... 33
6. Monitor Page by Browser ............................................................................................... 36
6.1 iMonitor monitor page .......................................................................................... 36
6.1.1 Group List .................................................................................................. 37
FATEK IoT User Manual
3
6.1.2 Historic Trend ............................................................................................ 43
6.2 iAccess Monitoring ................................................................................................ 44
6.2.1 Detail ........................................................................................................ 45
6.2.2 Device Log Information .............................................................................. 46
6.3 iLocation Map Display ........................................................................................... 48
6.3.1 GPS Settings .............................................................................................. 48
7 FATEK IoT App ................................................................................................................. 49
7.1 Take Android System as example (ios screen refer to Android) .......................... 49
7.1.1 Device Management .................................................................................. 49
7.1.2 iMonitor Group Detail ................................................................................ 50
7.1.3 iMonitor Search Function ........................................................................... 51
7.1.4 iAccess Device Detail .................................................................................. 52
7.1.5 iAccess Search Function ............................................................................. 53
8 FvDesigner and HMI Settings ......................................................................................... 54
8.1 FATEK IoT HMI System Settings Description ........................................................ 54
8.2 FATEK IoT FvDesigner Project Function Description ............................................ 56
9 FvDesigner Remote Maintenance .................................................................................. 59
9.1 Maintain HMI Project ............................................................................................ 64
9.2 Communicate with PLC by Pass Through Function .............................................. 65
9.3 Remote HMI Monitoring ....................................................................................... 65
FATEK IoT User Manual
4
Table Catalog
Table 1: Management Page .......................................................................................... 14
Table 2: Device group management description ......................................................... 15
Table 3: Add User ......................................................................................................... 18
Table 4: Add iMonitor device ....................................................................................... 22
Table 5: Dataitem settings ............................................................................................ 24
Table 6: Dataitem group settings ................................................................................. 26
Table 7: Build trend group ............................................................................................ 28
Table 8: Device settings ................................................................................................ 30
Table 9: Device group ................................................................................................... 31
Table 10: Dataitem Settings ......................................................................................... 34
Table 11: Monitor page ................................................................................................ 36
Table 12: Monitor page ................................................................................................ 37
Table 13: Device status ................................................................................................. 39
Table 14: iMonitor group detail ................................................................................... 41
Table 15: Monitor page ................................................................................................ 43
Table 16: Monitor page ................................................................................................ 44
Table 17: Detail information ........................................................................................ 45
Table 18: iAccess device detail ..................................................................................... 47
Table 19: Android management ................................................................................... 49
Table 20: Android group detail ..................................................................................... 50
Table 21: iMonitor search function .............................................................................. 51
Table 22: iAccess device group .................................................................................... 52
Table 23: iAccess search function ................................................................................ 53
Table 24: IoT Settings ................................................................................................... 54
Table 25: IoT Services Settings ..................................................................................... 56
Table 26: Login page ..................................................................................................... 60
Table 27: Device group ................................................................................................. 62
Table 28: Remote function ........................................................................................... 63
-
FATEK IoT User Manual
5
Figure Catalog
Figure 1: FATEK IoT network connection application scenario .................................... 10
Figure 2: iMonitor setting step..................................................................................... 11
Figure 3: iAccess setting process .................................................................................. 12
Figure 4: Website management login page ................................................................. 13
Figure 5: Management page ........................................................................................ 13
Figure 6: iMonitor management configuration example ............................................. 16
Figure 7: iAccess management configuration example ............................................... 17
Figure 8: User Management ........................................................................................ 18
Figure 9: Add User ........................................................................................................ 18
Figure 10: Registration Letter Certification .................................................................. 20
Figure 11: Add device ................................................................................................... 21
Figure 12: Add iMonitor device ................................................................................... 22
Figure 13: Add new dataitem ....................................................................................... 23
Figure 14: Add iMonitor dataitem ............................................................................... 23
Figure 15: iMonitor dataitem list ................................................................................. 25
Figure 16: Add dataitem group .................................................................................... 26
Figure 17: Add iMonitor device group ......................................................................... 26
Figure 18: Add iMonitor device group list ................................................................... 27
Figure 19: Add new trend ............................................................................................ 27
Figure 20: Build trend group ........................................................................................ 28
Figure 21: Trend list ...................................................................................................... 28
Figure 22: Add device ................................................................................................... 29
Figure 23: Add iAccess device ...................................................................................... 29
Figure 24: Add device group ........................................................................................ 31
Figure 25: Add iAccess dataitem .................................................................................. 31
Figure 26: iAccess device group list ............................................................................. 32
Figure 27: Add new dataitem ....................................................................................... 33
Figure 28: Add new iAccess dataitem .......................................................................... 33
Figure 29: iAccess device list ........................................................................................ 35
Figure 30: iMonitor monitor page ............................................................................... 36
Figure 31: iMonitor value monitor ............................................................................... 37
Figure 32: iMonitor trend ............................................................................................ 38
Figure 33: iMonitor device status ................................................................................ 39
Figure 34: iMonitor data log ........................................................................................ 40
Figure 35: iMonitor alarm events ................................................................................ 41
Figure 36: Data Log ...................................................................................................... 42
Figure 37: Alarm Event ................................................................................................. 42
FATEK IoT User Manual
6
Figure 38: Historic Trend .............................................................................................. 43
Figure 39: iMonitor monitor page ............................................................................... 44
Figure 40: iAccess device detail ................................................................................... 45
Figure 41: iAccess activation log .................................................................................. 46
Figure 42: iAccess logging log ...................................................................................... 46
Figure 43: iAccess connection log ................................................................................ 47
Figure 44: iLocation monitor page ............................................................................... 48
Figure 45: iLocation coordinate setting ....................................................................... 48
Figure 46: Android management page ........................................................................ 49
Figure 47: Android group detail ................................................................................... 50
Figure 48: iMonitor search function ............................................................................ 51
Figure 49: iAccess device group ................................................................................... 52
Figure 50: iAccess search function ............................................................................... 53
Figure 51: Servers/IoT setting button in system setting .............................................. 54
Figure 52: IoT Setting page .......................................................................................... 54
Figure 53: iAccess supported functions ....................................................................... 55
Figure 54: Unit Setting page for IoT Services ............................................................... 56
Figure 55: Setting page for iLocation in static type ...................................................... 58
Figure 56: Setting page for iLocation in dynamic type................................................. 58
Figure 57: FvDesigner iAccess remote maintenance function schematic diagram ..... 59
Figure 58: The location of iAccess in FvDesigner ......................................................... 59
Figure 59: iAccess login page ....................................................................................... 60
Figure 60: iAccess forget password page ..................................................................... 61
Figure 61: Device list in iAccess.................................................................................... 62
Figure 62: Device detail information in iAccess ........................................................... 63
Figure 63: iAccess download setting page ................................................................... 64
Figure 64: iAccess upload setting page ........................................................................ 64
Figure 65: iAccess Pass Through setting page .............................................................. 65
Figure 66: Enable Viewer function ............................................................................... 65
Figure 67: Viewer real-time screen .............................................................................. 66
FATEK IoT User Manual
7
FATEK IoT User Manual
1. Summary
To connect to a remote device via a network, complex setups are often required
to obtain HMI or PLC device data. Even if all settings were configured properly,
there will be many online restrictions and data security problems, resulting in
inefficient and inconvenient use of the system. Meanwhile, also because of the
high cost of construction etc., users may finally abandon this function. The FATEK
IoT cloud service platform provides a solution to make it easier.
FATEK IoT offers a new solution of HMI and PLC remotely monitoring named
"iMonitor". As long as the devices can connect to the Internet, users can easily
get the data on the devices, simultaneously monitor and access multiple devices
and receive real-time data, system alarms, data log which are useful for remotely
debugging. The communication security also has a professional security
encryption mechanism, so that the operation and access to equipment
information has effective protection. With these functions above, user does not
need to make any network settings.
FATEK IoT also provides iAccess remote maintenance. When the device is in a
foreign country far away, maintenance personnel do not need to spend a lot of
traffic and travel there and do troubleshooting on site. With iAccess, you can easily
connect to the device, download program and debug on line. In addition, iAccess
and FATEK HMI Pass Through function are perfectly integrated, users can directly
monitor PLC data and update PLC program through iAccess, and can also operate
the HMI at the same time without interruption.
Main Features:
⚫ Easy to setup simple device and personnel group management
⚫ Secure connection
⚫ Remote monitoring and maintenance of HMI and PLC
⚫ Support data log and trend analysis
⚫ Support alarm events log and notifications (SMS, e-mail and App
notifications)
⚫ Support Google map to trace device location with Google map
FATEK IoT User Manual
8
⚫ Support Android and iOS App
System Requirement:
⚫ P5, P2K with new generation ethernet-type HMI
⚫ Internet connection
⚫ Support Google Chrome, Firefox, Safari browser
⚫ Android: 5.0 or newer version later
⚫ iOS 11 or newer version
⚫ FvDesigner V1.5.48 or above
⚫ OS V2.0.2 or above
FATEK IoT User Manual
9
2. Application Introduction
Traditionally, connect to a network device needs to know the network
environment and settings, it might need to set up router or firewall. There may
also be a set of WAN IP restrictions that can only be wired to one device. Even
the network environment is too complicated to set up one by one.
FATEK IoT provides two main services, iMonitor and iAccess. As long as you
connect to the Internet, users can easily monitor device data with simply device
settings. The two service application scenarios are slightly different. The users can
plan the cloud service system according to their needs. The two services can be
used at the same time without conflict. The iLocation feature is also available to
display device locations on Google Maps.
Select the scenarios and features of the iMonitor:
⚫ There are multiple HMI and PLC scattered in different areas and the data on
these devices should be monitored at the same time.
⚫ Set alarm conditions to specific register address, if conditions are met then
SMS or email can be sent to the user admin for on-site troubleshooting.
⚫ If you want to analyze the time or the data changes, record the data and
acquire the system status through the historic trend.
⚫ No need to redownload the HMI project, can configure and modify the
register address through browser.
⚫ Adjustable device return time interval or return when changed, can reduce
the use of network bandwidth.
⚫ GPS location information can be set on the device, and the FATEK IoT can be
logged in through the browser to view the distribution location of the
device.
Select the scenarios and features of the iAccess:
⚫ There is a requirement to change the application of the program, to use
remote maintenance or update system functions.
⚫ Monitor specific single device data in real time and support real time trend
analysis.
⚫ GPS location information can be set on the device, and the FATEK IoT can be
logged in through the browser to view the distribution location of the
device.
FATEK IoT User Manual
10
Figure 1: FATEK IoT network connection application scenario
FATEK IoT User Manual
11
3. Device Activation Process
Before using FATEK IoT service, user needs to submit application to FATEK to
obtain Customer ID and User Admin to log in to website for manage system
configuration.
3.1 FATEK IoT System Setting - Enter HMI system setting page
- Click ‘Servers/IoT’, check the checkbox to enable IoT services
- Setting service password, check whether the ‘i’ icon turns green, it turns
green then represent it works.
3.2 iMonitor Devices that support the iMonitor function can be connected to FATEK IoT
Cloud, please apply to FATEK before use.
Figure 2: iMonitor setting step
FATEK IoT User Manual
12
3.3 iAccess Each of the device needs to have a unique LID to use iAccess. It cannot
transfer to other devices after activated.
Figure 3: iAccess setting process
FATEK IoT User Manual
13
4. Website Management System
Select the corresponding website for different market needs
World Wide User https://fatekcloud.net
China User https://fatekiot.cn
Figure 4: Website management login page
After logging in to the account, you can enter the IoT management page.
Figure 5: Management page
FATEK IoT User Manual
14
Note: The figure above shows the Administrator login page, so the users can
see the "Management" option on the left side. If it’s not the Administrator
account, then users can only see the "Services" option.
Table 1: Management Page
Item Function
Monitor
Page
iMonitor Monitor iMonitor dataitem page
iAccess Display iAccess device status and information
iLocation Let iMonitor dataitem group and iAccess
device group display on Google map, easily
for user to search device and monitor data.
Management User Configure user information and setting
permissions.
iMonitor data Configure iMonitor device and dataitem, and
set the trend to display.
iAccess device Configure iAccess device and dataitem.
Resource Usage Display the resource usage, if the usage is
full, please contact to the User Admin.
Language Website management system support three
kinds of languages.
Contact Customer Service Can directly send email to FATEK customer
service for help.
Manual Download Download the related manual and data.
Account Settings Set customer ID.
Logout Logout management system.
FATEK IoT User Manual
15
5. Management
Before using FATEK IoT service, users need to submit application to FATEK to
get Customer ID and User Admin permission to login to website management
system to configure. Only User Admin has the right to change other users'
operation authority.
Table 2: Device group management description
Item Description
Customer ID Customer ID is the concept of this managing function, a customer ID can
include the configuration of users, HMI devices, dataitem groups and
device groups.
User Admin Each Customer ID corresponding to a User Admin manager who can
configure the project’s user-related information and permission, also
device, dataitems, dataitem groups and device groups.
User Users belonging to different access permission group can do the basic
operation of monitor page.
Dataitem Get the basic dataitem settings of the device. Each dataitem can
assigned to more than one dataitem groups.
Dataitem Group The monitor page and historic trend are display in groups, the dataitems
in the group can come from different devices.
Device Group Devices shown in monitoring pages are organized by device groups, and
each device can be assigned to more than one device group.
Note: Each device can only join under one customer ID project at the same time. To
join to another project, needs to remove the device in the original customer ID then
add it to the new one.
FATEK IoT User Manual
16
The following figure shows the iMonitor management configuration example, with
this example we can know:
⚫ User Admin is the user manager, manage user Jordan and user Kobe. Jordan
use the Data Item group permission 1/2/4 and Kobe use the Data Item
Group permission 3/4.
⚫ iMonitor is configured by Data Items.
⚫ Multiple users can use the same group Data Item Group 4.
⚫ Data Items in Data Item Group 3 can come from different devices, Data A
comes from HMI A, Data D/F comes from HMI B.
⚫ Data Item Data A can assigned to more than one groups, Data Item Group 1
and Data Item Group 3.
Figure 6: iMonitor management configuration example
FATEK IoT User Manual
17
The following figure shows the iAccess management configuration example, with
this example we can know:
⚫ User Admin is the user manager, manage user Jordan and user Kobe. Jordan
use the Data Item group permission 1/2/4 and Kobe use the Data Item
Group permission 3/4.
⚫ iAccess is classify by device, if have the permission to use the device, all
planned data items under the device can be accessed in time via App.
⚫ Multiple users can use the same group Device Group 4.
⚫ Device A can assigned to more than one groups, Device Group 1 and D
Device Group 3.
Figure 7: iAccess management configuration example
FATEK IoT User Manual
18
5.1 User Management Add new user’s configuration and function authority, it can monitor each
user’s status.
5.1.1 User List
Figure 8: User Management
Figure 9: Add User
Table 3: Add User
Item Description
iMonitor user Number of existing users and maximum number of user accounts.
iAccess user Number of existing users and maximum number of user accounts.
Name Set the user name.
Account (Email) Set the user login account.
Password Set the user login password.
FATEK IoT User Manual
19
Nickname Set the user’s nickname.
Title Set the user’s title.
Description Set the description about the user.
iMonitor Disable Whether the user can use the iMonitor service or not.
iAccess Disable Whether the user can use the iAccess service or not.
Black List Forbid the user to log in to the IOT management page
FATEK IoT User Manual
20
5.1.2 Account Certification
1. After adding a User Admin or User, go to the registered email to check up
the registration authentication letter to activate the account (Figure 10).
2. User list (Figure 8) will display ‘Activated’ or ‘Resend’ two kinds of
certification status.
Figure 10: Registration Letter Certification
Note: The certification letter will expire after 72 hours.
FATEK IoT User Manual
21
5.2 iMonitor Data Management Set up multiple devices and monitor the data of each register at the same time, set
each dataitem group and set alarm conditions, you can send SMS text messages,
E-Mail or push broadcast notifications, and you can understand the system status
through trend graph groups.
5.2.1 iMonitor add device
Figure 11: Add device
FATEK IoT User Manual
22
Figure 12: Add iMonitor device
Table 4: Add iMonitor device
Item Description
Name Device name.
Product Type Only supports FATEK HMI currently, other types of devices will be
supported in the future.
Service Password The service password for the device that paired with must be the same
as FATEK IoT to connect properly.
Hardware ID The unique hardware ID for the device.
Description User setting information
Link Device Add new link device to connection.
FATEK IoT User Manual
23
5.2.2 iMonitor add new dataitem
Figure 13: Add new dataitem
Figure 14: Add iMonitor dataitem
FATEK IoT User Manual
24
Table 5: Dataitem settings
Item Description
Select Device Select the device to get data.
Dataitem Name Dataitem name.
Data Format Bit
16Bit-BCD
16Bit-INT
16Bit-UINT
16Bit-HEX
32Bit-BCD
32Bit-INT
32Bit-UINT
32Bit-HEX
32Bit-FLOAT
ASCII String
Length Data length.
Comment Information field.
Address Register address of the device. This content needs to be the same as the
device connection information, otherwise the value will not be updated.
Update Mode Mode for device to return data.
Period*Note 1 According to [Period Time] to return data periodically.
Trigger Return data when the value has changed.
Period Time Use in the periodic update mode, increase the time can reduce the
network bandwidth usage and reduce the system loading.
Data Log Enable Enable the data log function.
Alarm Enable Enable alarm function.
Alarm Condition When the condition to trigger an alarm is met, the alarm will be sent.
Alarm Content User customize the alarm content to be sent.
Send Email Send message via email.
App Notifications Push notification of the alarm message to mobile APP.
Send SMS
Message*Note 2
Send message via SMS message.
Alarm Contact Receiver of the alarm message.
Recurrence
Interval (Minutes)
*Note 3
When alarm is triggered and send the first SMS, e-mail or push
notification, this is used to determine the interval to send the message
again until the alarm is cleared.
Transfer Delay When the alarm condition is triggered, this is used to determine delay
FATEK IoT User Manual
25
Time (Second) how many times to send SMS, e-mail or APP push notification. This
function is to avoid sending too much message when the value changed
in a limited time.
Note 1: The minimum value is 60 seconds.
Note 2: Sending SMS might cost the extra fee.
Note 3: When the retransmission interval is set to "0" minutes, the alarm
notification will be sent only once and stop resending.
After setting up the dataitem, users can see the data in the device list.
Figure 15: iMonitor dataitem list
FATEK IoT User Manual
26
5.2.3 iMonitor add new dataitem group
Figure 16: Add dataitem group
Figure 17: Add iMonitor device group
Table 6: Dataitem group settings
Item Description
Dataitem Group
Name
Group name.
Upload Set the group icon.
FATEK IoT User Manual
27
GPS Source*Note 1 Device’s source address.
Description Set your own description.
Add Device To add devices to the group, the right-side arrow provides the
drop-down menu for users to add dataitems into the group.
User Add users who can monitor this group.
Note 1: Need to set in the FvDesigner, please refer to chapter 8.2-FATEK IoT FvDesigner
Project Function Description
After setting up, users can see the group in the dataitem group list.
Figure 18: Add iMonitor device group list
5.2.4 iMonitor add new trend
Figure 19: Add new trend
FATEK IoT User Manual
28
Figure 20: Build trend group
Table 7: Build trend group
Item Description
Trend Name Set the trend name.
Y-axis Unit Set the Y-axis unit.
Select Dataitem
Group
Add groups to the trend and select the group’s dataitem.
After finish setting, users can see the item in the trend list.
Figure 21: Trend list
FATEK IoT User Manual
29
5.3 iAccess Device Management Set up the devices and provide the remote upload/download maintenance, also can
perform real-time monitor and trend analysis.
5.3.1 iAccess add device
Figure 22: Add device
Figure 23: Add iAccess device
FATEK IoT User Manual
30
Table 8: Device settings
Item Description
Name Device name
Product Type Currently only supports FATEK HMI, other types of devices will be
supported in the future.
Service Password The service password for the device that paired with the FATEK IoT must
be the same to connect properly.
Hardware ID The unique hardware ID for the device.
Description User setting information
Link Device Add new link device to connection.
FATEK IoT User Manual
31
5.3.2 iAccess add Dataitem Group
Figure 24: Add device group
Figure 25: Add iAccess dataitem
Table 9: Device group
Item Description
Dataitem Group
Name
Group name.
Upload Set the group icon.
GPS Source*Note 1 Device’s source address.
FATEK IoT User Manual
32
Description Set your own description.
Add Dataitem Add devices to the group.
User Add users who can monitor this group.
Note 1: Need to set in the FvDesigner, please refer to chapter 8.2-FATEK IoT FvDesigner Project
Function Description
After setting up, users can see the groups in the group list.
Figure 26: iAccess device group list
FATEK IoT User Manual
33
5.3.3 iAccess add new dataitem
Figure 27: Add new dataitem
Figure 28: Add new iAccess dataitem
FATEK IoT User Manual
34
Table 10: Dataitem Settings
Item Description
Select Device Select the device to get data.
Dataitem Name Dataitem name.
Data Format
Bit
16Bit-BCD
16Bit-INT
16Bit-UINT
16Bit-HEX
32Bit-BCD
32Bit-INT
32Bit-UINT
32Bit-HEX
32Bit-FLOAT
ASCII String
Length Data length.
Comment Information field.
Address Register address of the device. This content needs to be the same as the
device connection information, otherwise the value will not be updated.
Update mode Mode for device to return data.
Period According to [Period Time] to return data periodically.
Value
Changed
Return data when the value has changed.
Period Time*Note 1 Use in the periodic update mode, increase the time can reduce the
network bandwidth usage and reduce the system loading.
Note 1: The minimum value is 1 second.
FATEK IoT User Manual
35
After setting up, you can see the data from the device list.
Figure 29: iAccess device list
FATEK IoT User Manual
36
6. Monitor Page by Browser
Fully monitor all data through the browser to ensure the device’s status.
6.1 iMonitor monitor page
Figure 30: iMonitor monitor page
Table 11: Monitor page
Item Description
Dataitem Group Dataitem Group name.
Location
Coordinate
Display the GPS coordinate of the device.
Alarm Status
Alarm Alarm occurred.
Normal Normal Status, no alarm occurs.
Dataitem Dataitem name.
Connection Status
Online Device is connecting to FATEK IoT.
Offline Device is not connecting to FATEK IoT.
Abnormal Device is connecting to FATEK IoT, but data settings or
communication is incorrect.
Value The return value from the device address.
Last Update Last update time.
FATEK IoT User Manual
37
Detail Detail information of dataitem, including trend display, value operation
setting, historic data and alarm events.
Search
Quickly search the list of groups or dataitems.
6.1.1 Group List
6.1.1.1 Group Detail Setting
Figure 31: iMonitor value monitor
Table 12: Monitor page
Item Description
Dataitem Dataitem group name.
Connection
Status
Online Device is connecting to FATEK IoT.
Offline Device is not connecting to FATEK IoT.
Abnormal Device is connecting to FATEK IoT, but data settings or
communication is incorrect.
Alarm Status
Alarm Alarm occurred.
Normal Normal Status, no alarm occurs.
Value The return value from the device address.
Last
Update*Note 1
The time for the last update.
Note 1: The update speed is depending on the chapter 5.2.2- update mode
FATEK IoT User Manual
38
Open each dataitem options can see the real-time trend, set the start and
end time to display the data.
Figure 32: iMonitor trend
FATEK IoT User Manual
39
6.1.1.2 Device Status
Figure 33: iMonitor device status
Table 13: Device status
Item Description
OS_VER OS version of the device system.
ENV_VER Environment package version of the device system.
FW_VER Firmware version of the device system.
FATEK IoT User Manual
40
6.1.1.3 Data Log
Figure 34: iMonitor data log
Note: Data Log function will log data per hour.
Note: When the numbers of the log have reached the limitation then it will
not record the data.
FATEK IoT User Manual
41
6.1.1.4 Alarm Events
Figure 35: iMonitor alarm events
Table 14: iMonitor group detail
Note: From the triggered alarm to recovery stands for 1 record, if the alarms
different registers then the events will be calculated together.
Note: The push notification times is not related to the alarm occurred times.
Note: When the number of the alarms has reached the limitation then it will
not record the data, but it won’t affect the SMS, E-mail, or push notification if
the alarm occurred.
Item Description
Detail Device version, system status information, data log and alarm event log.
Dataitem List Monitoring Data and Trend Chart
Device Status The data log collected by on-site devices.
DataLog The data log collected by on-site devices.
Alarm Event Alarms recorded by devices.
FATEK IoT User Manual
42
6.1.1.5 Support Downloading Cloud Data
Provide downloading data log data.
Figure 36: Data Log
Provide downloading alarm events
Figure 37: Alarm Event
Note: Currently only the .CSV file download format is available.
FATEK IoT User Manual
43
6.1.2 Historic Trend
Figure 38: Historic Trend
Table 15: Monitor page
Item Description
Trend The record of the data log.
Time Range Set the historical interval to see the data.
FATEK IoT User Manual
44
6.2 iAccess Monitoring
Figure 39: iMonitor monitor page
Table 16: Monitor page
Item Description
Device Group Device Group name.
Location
Coordinate
Display the GPS coordinate of the device.
Device Device name.
Product Type FATEK IoT supports FATEK HMI currently, other types of devices will be
supported in the future.
Model Name Display the HMI model name, such as P5070N.
iAccess Status Four kinds of status below:
Inactivated LID is not activated and the device cannot be used.
Offline LID is activated but device is not connecting.
Online
Standby
Device is connecting with FATEK IoT but there is no
user doing operation.
Online Used Device is connecting with FATEK IoT and the user is
operating, only one user can operate at the same time.
Information Device version and system information, also related device activated and
record log of active/connected devices.
Search
Quickly search the list of groups or devices.
FATEK IoT User Manual
45
6.2.1 Detail
Figure 40: iAccess device detail
Table 17: Detail information
Item Description
OS_VER OS version of the device system.
ENV_VER Environment package version of the device system.
FW_VER Firmware version of the device system.
FATEK IoT User Manual
46
6.2.2 Device Log Information
Figure 41: iAccess activation log
Figure 42: iAccess logging log
FATEK IoT User Manual
47
Figure 43: iAccess connection log
Table 18: iAccess device detail
Item Description
Detail Device version, system status information and connection log.
Detail
information
Device system status information.
Activation
Log
The time that when enter LID and the first time
connect to FATEK IoT.
Logging Log The time that device logged in to FATEK IoT.
Connection
Log
The time that mobile device connected to FATEK IoT.
FATEK IoT User Manual
48
6.3 iLocation Map Display iLocation displays the data distribution of devices and systems in each area
through maps, and more intuitive maintenance and monitor system data
through geographical location information.
Figure 44: iLocation monitor page
6.3.1 GPS Settings
To display the icon on the map, be sure to set [GPS Source] in the
dataitem group or device group.
Figure 45: iLocation coordinate setting
FATEK IoT User Manual
49
7 FATEK IoT App
FATEK IoT App can be supported on Android and iOS, the app supports iMonitor
and iAccess services. The content and information are very similar with website,
it’s convenient for users to monitor and maintain system status.
IOS App : https://apps.apple.com/tw/app/fatek-iot/id1453667290?l=en
Android App : https://play.google.com/store/apps/details?id=com.fatek.iot
7.1 Take Android System as example (ios screen refer to Android)
7.1.1 Device Management
Figure 46: Android management page
Table 19: Android management
Item Function
Monitor
Page
iMonitor Group List Monitor iMonitor dataitem page.
Historic
Trend
Display the recorded dataitem.
iAccess Display iAccess device status and information
Account Settings Customer ID and related setting modification.
Search Quickly to search for group list or device item.
Notification Record all alarm occurred status.
FATEK IoT User Manual
50
7.1.2 iMonitor Group Detail
Figure 47: Android group detail
Table 20: Android group detail
Item Function
Dataitem List Monitor and modify dataitem.
Device Status Device system status information.
Alarm Event Display the record of device alarm.
FATEK IoT User Manual
51
7.1.3 iMonitor Search Function
Figure 48: iMonitor search function
Table 21: iMonitor search function
Item Function
Dataitem Search for dataitems in a group.
Group Search for group items in the group list.
FATEK IoT User Manual
52
7.1.4 iAccess Device Detail
Figure 49: iAccess device group
Table 22: iAccess device group
Item Function
Device Group List Device detail list.
Device Detail Real time monitor the modified device data.
FATEK IoT User Manual
53
7.1.5 iAccess Search Function
Figure 50: iAccess search function
Table 23: iAccess search function
Item Function
Device Search for dataitems in the device.
Device Group Search for device items in the device list.
FATEK IoT User Manual
54
8 FvDesigner and HMI Settings
The above sections describe the settings and usage instructions of the FATEK IoT
website. This chapter describes the HMI system settings and related project
functions that must be set according to the FATEK IoT.
8.1 FATEK IoT HMI System Settings Description Enter system setting page, the ‘’Servers/IoT’’ setting button can be found on
HMI that supports IoT function.
Figure 51: Servers/IoT setting button in system setting
Click ‘’Servers/IoT’’ setting button to enter the IoT setting page.
Figure 52: IoT Setting page
Table 24: IoT Settings
Item Description
Enable IoT Service Check the checkbox to enable iMonitor and iAccess.
Host Select the apply server.
China User: fatekiot.cn
World Wide User: fatekcloud.net
HWID Read only and unique ID code, it must be set when setting up the device
FATEK IoT User Manual
55
on the FATEK IoT website to represent this HMI has been register to
FATEK IoT.
Service Password Service Password for iMonitor and iAccess, user can set it up. When
setting up the device on FATEK IoT website, needs to field up the same
service password to activate iMonitor or iAccess.
Enable iAccess Check the checkbox to enable iAccess.
LID Authentication code for iAccess, need to get LID through dealer.
Enable iAccess
Viewer
According to different LID will affect whether this function is provided or
not.
Mask Passwords Display or mask password.
Note: The icon on the right side is use for checking the connection
status.
Click iAccess icon and will pop up the supported function window.
Figure 53: iAccess supported functions
FATEK IoT User Manual
56
8.2 FATEK IoT FvDesigner Project Function Description Enter the FvDesigner -> Unit Setting -> IoT Services:
Figure 54: Unit Setting page for IoT Services
Table 25: IoT Services Settings
Item Description
iMonitor Status
Address Check this item to enable iMonitor status address. can display the
status code, shown as below:
iAccess Status
Address Check this item to enable iAccess status address. can display the
status code, shown as below:
FATEK IoT User Manual
57
iLocation When enable iLocation, HMI will send GPS message to FATEK IoT
periodically.
Type HMI iLocation has two types:
Static: Constant. Use Google Map to get the real location as GPS
message.
Dynamic: Set latitude/longitude degree address so GPS message can
change dynamically.
GPS Format Provide DD, DMM and DMS three types of format.
When is in dynamic type, the definition will be different with different
formats, rules shown as below:
⚫ The format is in 32Bit-INT
⚫ Negative number are south latitude or west longitude, positive
number are north latitude or east longitude.
⚫ Range
North Latitude (0~900,000,000), South Latitude (0~900,000,000) ;
East Longitude (0~1,800,000,000), West Longitude (0~1,800,000,000)
FATEK IoT User Manual
58
DD format description of dynamic address
Decimal 10 9 8 7 6 5 4 3 2 1
Description Degree
(Longitude 0~180)
(Latitude 0~90)
Decimal
DMM format description of dynamic address
Decimal 10 9 8 7 6 5 4 3 2 1
Description Degree
(Longitude 0~180)
(Latitude 0~90)
Minutes
(0~59)
Decimal
DMS format description of dynamic address
Decimal 10 9 8 7 6 5 4 3 2 1
Description Degree
(Longitude 0~180)
(Latitude 0~90)
Minutes
(0~59)
Seconds
(0~59)
Decimal
Figure 55: Setting page for iLocation in static type
Figure 56: Setting page for iLocation in dynamic type
FATEK IoT User Manual
59
9 FvDesigner Remote Maintenance
The iAccess remote maintenance function through FvDesigner can easily
maintain HMI without HMI IP address. The following will firstly introduce how to
use iAccess tool, then chapter9.1 will introduce how to use the FvDesigner
iAccess function to maintain HMI project. Chapter9.2 will introduce how to use
FvDesigner iAccess function to communicate with PLC via HMI Pass Through
function.
Figure 57: FvDesigner iAccess remote maintenance function schematic diagram
Figure 58: The location of iAccess in FvDesigner
FATEK IoT User Manual
60
Login Page
Figure 59: iAccess login page
Table 26: Login page
Item Description
Project User login project.
Account (Email) User login account.
Password User login password.
Server Select the applied server.
Forget Password Reset password.
Language Provide English, Traditional Chinese, Simplified Chinese, and Türkçe.
FATEK IoT User Manual
61
Provide “Forget Password” for users, and the new password can be modified after
sending the confirmation letter.
Figure 60: iAccess forget password page
FATEK IoT User Manual
62
After login successfully will display the device group tree diagram that the user has
the permission to view.
Click on the tree diagram to expand and you can see the device status
information of the device group.
Figure 61: Device list in iAccess
Table 27: Device group
Item Description
Name Device name, need to login to the website to set.
Product Type Display the product type.
Model Name Display the group’s model name.
iAccess Status Display the current status of the device.
Refresh Refresh the device status.
Logout Logout the account.
Detail Select the device then enter the remote function page.
FATEK IoT User Manual
63
Enter the device to use the remote maintenance function.
Figure 62: Device detail information in iAccess
Table 28: Remote function
Item Description
Name Device name.
Model Display the device model.
Firmware version Display the device firmware version.
OS version Display the device OS version.
Env version Display the device environment package version.
iAccess Status Display the connect status.
iAccess LID Display the LID type.
FATEK IoT User Manual
64
9.1 Maintain HMI Project Provide users to upload and download HMI project remotely.
Figure 63: iAccess download setting page
Figure 64: iAccess upload setting page
Note: for more details about【Download】and【Upload】settings please refer to
FvDesigner manual.
FATEK IoT User Manual
65
9.2 Communicate with PLC by Pass Through Function Using FvDesigner iAcess can do the communication with PLC that is connect
with HMI by using Pass Through.
Figure 65: iAccess Pass Through setting page
Note: for more details please refer to FvDesigner manual【Pass Through】.
9.3 Remote HMI Monitoring Provide users to monitor through remote connection without setting the fixed IP.
To enable this function, go to HMI system setting-> Servers/IoT, check to enable
iAccess Viewer.
Figure 66: Enable Viewer function
Real-time monitoring HMI screen.
FATEK IoT User Manual
66
Figure 67: Viewer real-time screen