Report No.: RF160202D06-1 Page No. 1 / 65 Report Format Version:6.1.1
FCC Test Report
Report No.: RF160202D06-1
FCC ID: EMJSE6B
Test Model: E6B
Received Date: Feb. 2, 2016
Test Date: Feb. 23 ~ Mar. 4, 2016
Issued Date: Mar. 18, 2016
Applicant: PRIMAX ELECTRONICS LTD.
Address: No. 669, Ruey Kuang Road, Neihu, Taipei, Taiwan, R.O.C.
Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch
Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan (R.O.C.)
This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies.
Report No.: RF160202D06-1 Page No. 2 / 65 Report Format Version:6.1.1
Table of Contents
Release Control Record ............................................................................................................................. 4
1 Certificate of Conformity ................................................................................................................. 5
2 Summary of Test Results ................................................................................................................ 6
2.1 Measurement Uncertainty............................................................................................................... 6
2.2 Modification Record........................................................................................................................ 6
3 General Information ......................................................................................................................... 7
3.1 General Description of EUT ............................................................................................................ 7
3.2 Description of Test Modes .............................................................................................................. 9
3.2.1 Test Mode Applicability and Tested Channel Detail ........................................................................ 10
3.3 Duty Cycle of Test Signal .............................................................................................................. 12
3.4 Description of Support Units ......................................................................................................... 13
3.4.1 Configuration of System under Test .............................................................................................. 14
3.5 General Description of Applied Standard ...................................................................................... 16
4 Test Types and Results.................................................................................................................. 17
4.1 Radiated Emission and Bandedge Measurement.......................................................................... 17
4.1.1 Limits of Radiated Emission and Bandedge Measurement ............................................................ 17
4.1.2 Test Instruments ........................................................................................................................... 18
4.1.3 Test Procedure ............................................................................................................................. 19
4.1.4 Deviation from Test Standard ........................................................................................................ 19
4.1.5 Test Setup .................................................................................................................................... 20
4.1.6 EUT Operating Condition .............................................................................................................. 20
4.1.7 Test Results .................................................................................................................................. 21
4.2 Conducted Emission Measurement .............................................................................................. 40
4.2.1 Limits of Conducted Emission Measurement ................................................................................. 40
4.2.2 Test Instruments ........................................................................................................................... 40
4.2.3 Test Procedure ............................................................................................................................. 41
4.2.4 Deviation from Test Standard ........................................................................................................ 41
4.2.5 Test Setup .................................................................................................................................... 41
4.2.6 EUT Operating Condition .............................................................................................................. 41
4.2.7 Test Results .................................................................................................................................. 42
4.3 Transmit Power Measurment ........................................................................................................ 46
4.3.1 Limits of Transmit Power Measurement ........................................................................................ 46
4.3.2 Test Setup .................................................................................................................................... 46
4.3.3 Test Instruments ........................................................................................................................... 46
4.3.4 Test Procedure ............................................................................................................................. 47
4.3.5 Deviation from Test Standard ........................................................................................................ 47
4.3.6 EUT Operating Condition .............................................................................................................. 47
4.3.7 Test Result ................................................................................................................................... 48
4.4 Peak Power Spectral Density Measurement ................................................................................. 53
4.4.1 Limits of Peak Power Spectral Density Measurement .................................................................... 53
4.4.2 Test Setup .................................................................................................................................... 53
4.4.3 Test Instruments ........................................................................................................................... 53
4.4.4 Test Procedure ............................................................................................................................. 53
4.4.5 Deviation from Test Standard ........................................................................................................ 54
4.4.6 EUT Operating Condition .............................................................................................................. 54
4.4.7 Test Results .................................................................................................................................. 55
4.5 Frequency Stability Measurement ................................................................................................. 59
4.5.1 Limits of Frequency Stability Measurement ................................................................................... 59
4.5.2 Test Setup .................................................................................................................................... 59
4.5.3 Test Instruments ........................................................................................................................... 59
4.5.4 Test Procedure ............................................................................................................................. 59
4.5.5 Deviation from Test Standard ........................................................................................................ 59
Report No.: RF160202D06-1 Page No. 3 / 65 Report Format Version:6.1.1
4.5.6 EUT Operating Condition .............................................................................................................. 59
4.5.7 Test Results .................................................................................................................................. 60
4.6 6dB Bandwidth Measurment ......................................................................................................... 61
4.6.1 Limits of 6dB Bandwidth Measurement ......................................................................................... 61
4.6.2 Test Setup .................................................................................................................................... 61
4.6.3 Test Instruments ........................................................................................................................... 61
4.6.4 Test Procedure ............................................................................................................................. 61
4.6.5 Deviation from Test Standard ........................................................................................................ 61
4.6.6 EUT Operating Condition .............................................................................................................. 61
4.6.7 Test Results .................................................................................................................................. 62
5 Pictures of Test Arrangements ...................................................................................................... 64
Appendix – Information on the Testing Laboratories ............................................................................. 65
Report No.: RF160202D06-1 Page No. 4 / 65 Report Format Version:6.1.1
Release Control Record
Issue No. Description Date Issued
RF160202D06-1 Original release. Mar. 18, 2016
Report No.: RF160202D06-1 Page No. 5 / 65 Report Format Version:6.1.1
1 Certificate of Conformity
Product: My Passport Wireless Pro
Brand: WD
Test Model: E6B
Sample Status: Engineering sample
Applicant: PRIMAX ELECTRONICS LTD.
Test Date: Feb. 23 ~ Mar. 4, 2016
Standard: 47 CFR FCC Part 15, Subpart E (Section 15.407)
ANSI C63.10: 2013
The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd.,
Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data
evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts
of the measurements of the sample’s EMC characteristics under the conditions specified in this report.
Prepared by :
, Date: Mar. 18, 2016
Jessica Cheng / Senior Specialist
Approved by
:
, Date: Mar. 18, 2016
Rex Lai / Assistant Manager
Report No.: RF160202D06-1 Page No. 6 / 65 Report Format Version:6.1.1
2 Summary of Test Results
47 CFR FCC Part 15, Subpart E (SECTION 15.407)
FCC
Clause Test Item Result Remarks
15.407(b)(6) AC Power Conducted Emissions PASS Meet the requirement of limit.
Minimum passing margin is -14.46dB at 0.41953MHz.
15.407(b) (1/2/3/4/6)
Radiated Emissions & Band Edge Measurement
PASS Meet the requirement of limit.
Minimum passing margin is -4.2dB at 5850.00MHz.
15.407(a)(1/2/3)
Max Average Transmit Power PASS Meet the requirement of limit.
15.407(a)(1/2/3)
Peak Power Spectral Density PASS Meet the requirement of limit.
15.407(e) 6dB bandwidth PASS Meet the requirement of limit. (U-NII-3 Band only)
15.407(g) Frequency Stability PASS Meet the requirement of limit.
15.203 Antenna Requirement PASS No antenna connector is used.
2.1 Measurement Uncertainty
Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2:
Measurement Frequency Expended Uncertainty
(k=2) (±)
Conducted Emissions at mains ports 150kHz ~ 30MHz 2.78 dB
Radiated Emissions up to 1 GHz 30MHz ~ 1000MHz 4.00 dB
Radiated Emissions above 1 GHz 1GHz ~ 40GHz 3.36 dB
2.2 Modification Record
There were no modifications required for compliance.
Report No.: RF160202D06-1 Page No. 7 / 65 Report Format Version:6.1.1
3 General Information
3.1 General Description of EUT
Product My Passport Wireless Pro
Brand WD
Test Model E6B
Status of EUT Engineering sample
Power Supply Rating 5Vdc from Adapter or host equipment or 3.75Vdc from battery
Modulation Type 64QAM, 16QAM, QPSK, BPSK
256QAM for OFDM in 11ac mode only.
Modulation Technology OFDM
Transfer Rate
802.11a: 54/48/36/24/18/12/9/6Mbps
802.11n: up to 150Mbps
802.11ac: up to 434Mbps
Operating Frequency 5180 ~ 5240MHz
5745 ~ 5825MHz
Number of Channel
5180 ~ 5240MHz
4 for 802.11a, 802.11n (HT20)
2 for 802.11n (HT40)
1 for 802.11ac (VHT80)
5745 ~ 5825MHz
5 for 802.11a, 802.11n (HT20)
2 for 802.11n (HT40)
1 for 802.11ac (VHT80)
Output Power
5180 ~ 5240MHz
10.617 mW
5745 ~ 5825MHz
10.765mW
Antenna Type PCB antenna with 3.33dBi gain
Antenna Connector N/A
Accessory Device Adapter
Data Cable Supplied Shielded USB 3.0 cable (0.4m)
Note:
1. The EUT incorporates a SISO function. Physically, the EUT provides one completed transmitter and one receiver.
Modulation Mode TX FUNCTION
802.11a 1TX
802.11n (HT20) 1TX
802.11n (HT40) 1TX
802.11ac (VHT20) 1TX
802.11ac (VHT40) 1TX
802.11ac (VHT80) 1TX
Note: The modulation and bandwidth are similar for 802.11n mode for HT20 (HT40) and 802.11ac mode for VHT20 (VHT40), therefore investigated worst case to representative mode in test report. (Final test mode refer section 3.2.1)
Report No.: RF160202D06-1 Page No. 8 / 65 Report Format Version:6.1.1
2. The The EUT uses following adapter and battery.
Adapter
Brand SWITCHING MODE POWER SUPPLY
Model APP524-051240U
Input Power 100-240Vac, 50/60Hz, 0.45A MAX
Output Power 5.1Vdc 2.4A
Battery
Brand ROOFER
Model RDJ10 (Korra)
Spec. 3.75V/6400mAh (1S2P,3.75V/3200mAh * 2)
3. The EUT was pre-tested with the following modes: † Operating Mode (EUT stand-alone) † Operating + Charging Mode (EUT + Adapter)
The worst emission level was found when the EUT tested under Operating + Charging Mode (EUT + Adapter) therefore, only its test data was recorded in this report.
4. The above EUT information is declared by manufacturer and for more detailed features description, please refer to the manufacturer's specifications or user's manual.
Report No.: RF160202D06-1 Page No. 9 / 65 Report Format Version:6.1.1
3.2 Description of Test Modes
FOR 5180 ~ 5240MHz
4 channels are provided for 802.11a, 802.11n (HT20):
Channel Frequency Channel Frequency
36 5180 MHz 44 5220 MHz
40 5200 MHz 48 5240 MHz
2 channels are provided for 802.11n (HT40):
Channel Frequency Channel Frequency
38 5190 MHz 46 5230 MHz
1 channel is provided for 802.11ac (VHT80):
Channel Frequency
42 5210MHz
FOR 5745 ~ 5825MHz:
5 channels are provided for 802.11a, 802.11n (HT20):
Channel Frequency Channel Frequency
149 5745MHz 161 5805MHz
153 5765MHz 165 5825MHz
157 5785MHz
2 channels are provided for 802.11n (HT40):
Channel Frequency Channel Frequency
151 5755MHz 159 5795MHz
1 channel is provided for 802.11ac (VHT80):
Channel Frequency
155 5775MHz
Report No.: RF160202D06-1 Page No. 10 / 65 Report Format Version:6.1.1
3.2.1 Test Mode Applicability and Tested Channel Detail
EUT
CONFIGURE
MODE
APPLICABLE TO DESCRIPTION
RE≥1G RE<1G PLC APCM
A √ √ √ √ Operating + Charging (EUT with Adapter)
B - - √ - Read and write function( EUT with Notebook)
Where RE≥1G: Radiated Emission above 1GHz RE<1G: Radiated Emission below 1GHz
PLC: Power Line Conducted Emission APCM: Antenna Port Conducted Measurement
NOTE: The EUT had been pre-tested on the positioned of each 3 axis. The worst case was found when positioned on X-plane.
2. “-” means no effect.
Radiated Emission Test (Above 1GHz):
Pre-Scan has been conducted to determine the worst-case mode from all possible combinations
between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture).
Following channel(s) was (were) selected for the final test as listed below.
EUT
CONFIGURE
MODE
MODE FREQ. BAND
(MHz)
AVAILABLE
CHANNEL
TESTED
CHANNEL
MODULATION
TECHNOLOGY
MODULATION
TYPE
DATA
RATE
(Mbps)
A
802.11a
5180-5240
36 to 48 36, 40, 48 OFDM BPSK 6.0
802.11n (HT20) 36 to 48 36, 40, 48 OFDM BPSK 6.5
802.11n (HT40) 38 to 46 38, 46 OFDM BPSK 13.5
802.11ac (VHT80) 42 42 OFDM BPSK 29.3
802.11a
5745-5825
149 to 165 149, 157, 165 OFDM BPSK 6.0
802.11n (HT20) 149 to 165 149, 157, 165 OFDM BPSK 6.5
802.11n (HT40) 151 to 159 151, 159 OFDM BPSK 13.5
802.11ac (VHT80) 155 155 OFDM BPSK 29.3
Radiated Emission Test (Below 1GHz):
Pre-Scan has been conducted to determine the worst-case mode from all possible combinations
between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture).
Following channel(s) was (were) selected for the final test as listed below.
EUT
CONFIGURE
MODE
MODE FREQ. BAND
(MHz)
AVAILABLE
CHANNEL
TESTED
CHANNEL
MODULATION
TECHNOLOGY
MODULATION
TYPE
DATA
RATE
(Mbps)
A 802.11a 5180-5240 38 to 46 40 OFDM BPSK 6.0
Report No.: RF160202D06-1 Page No. 11 / 65 Report Format Version:6.1.1
Power Line Conducted Emission Test:
Pre-Scan has been conducted to determine the worst-case mode from all possible combinations
between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture).
Following channel(s) was (were) selected for the final test as listed below.
EUT
CONFIGURE
MODE
MODE FREQ. BAND
(MHz)
AVAILABLE
CHANNEL
TESTED
CHANNEL
MODULATION
TECHNOLOGY
MODULATION
TYPE
DATA
RATE
(Mbps)
A 802.11a 5180-5240 38 to 46 40 OFDM BPSK 6.0
B - - - - - - -
Antenna Port Conducted Measurement:
This item includes all test value of each mode, but only includes spectrum plot of worst value of each
mode. Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture).
Following channel(s) was (were) selected for the final test as listed below.
EUT
CONFIGURE
MODE
MODE FREQ. BAND
(MHz)
AVAILABLE
CHANNEL
TESTED
CHANNEL
MODULATION
TECHNOLOGY
MODULATION
TYPE
DATA
RATE
(Mbps)
A
802.11a
5180-5240
36 to 48 36, 40, 48 OFDM BPSK 6.0
802.11n (HT20) 36 to 48 36, 40, 48 OFDM BPSK 6.5
802.11n (HT40) 38 to 46 38, 46 OFDM BPSK 13.5
802.11ac (VHT80) 42 42 OFDM BPSK 29.3
802.11a
5745-5825
149 to 165 149, 157, 165 OFDM BPSK 6.0
802.11n (HT20) 149 to 165 149, 157, 165 OFDM BPSK 6.5
802.11n (HT40) 151 to 159 151, 159 OFDM BPSK 13.5
802.11ac (VHT80) 155 155 OFDM BPSK 29.3
Test Condition:
APPLICABLE TO MODE ENVIRONMENTAL
CONDITIONS INPUT POWER TESTED BY
RE≥1G A 18deg. C, 73%RH 5Vdc Aaron You
RE<1G A 18deg. C, 73%RH 5Vdc Aaron You
PLC A 22deg. C, 71%RH 120Vac, 60Hz (Adapter) Aaron You
B 22deg. C, 71%RH 120Vac, 60Hz (System) Aaron You
APCM A 25deg. C, 60%RH 5Vdc Dalen Dai
Report No.: RF160202D06-1 Page No. 12 / 65 Report Format Version:6.1.1
3.3 Duty Cycle of Test Signal
Duty cycle of test signal is 100 %.
802.11a 802.11n (HT20)
802.11n (HT40) 802.11ac (VHT80)
Report No.: RF160202D06-1 Page No. 13 / 65 Report Format Version:6.1.1
3.4 Description of Support Units
The EUT has been tested as an independent unit together with other necessary accessories or support units.
The following support units or accessories were used to form a representative test configuration during the
tests.
ID Product Brand Model No. Serial No. FCC ID Remarks
A. SD Card Transcend 4GB N/A N/A Provided by Lab
B. USB 3.0 Hard Disk WD WDBACY5000ABL-PESN WXQ1E61CMASL FCC DoC Approved Provided by Lab
C. Notebook DELL E5410 BW33YM1 FCC DoC Approved Provided by Lab
D. Notebook PC DELL E6530 9331GV1 FCC DoC Approved Provided by Lab
E. NOTEBOOK
COMPUTER DELL PP27L 8SNZ12S FCC DoC Approved Provided by Lab
Note:
1. All power cords of the above support units are non-shielded (1.8m).
2. Items C~D acted as communication partners to transfer data.
ID Descriptions Qty. Length (m) Shielding
(Yes/No) Cores (Qty.) Remarks
1. USB cable 1 0.4 Y 0 Supplied by client
2. USB cable 1 0.5 Y 0 Provided by Lab
Note: The core(s) is(are) originally attached to the cable(s).
Report No.: RF160202D06-1 Page No. 14 / 65 Report Format Version:6.1.1
3.4.1 Configuration of System under Test
Mode A Radiated Emission Test (Below 1GHz) Power Line Conducted Emission Test
Mode A Radiated Emission Test (Above 1GHz)
EUT
USB 3.0 Adapter (EUT) 1
USB 2.0
SD SD card (A)
Notebook PC (C) <For 2.4GHz>
USB Disk (B)
120Vac
Remote site Wireless Transmission
2
Notebook PC (D) <For 5GHz>
Wireless Transmission
EUT
USB 3.0 Adapter (EUT) 1
USB 2.0
SD
120Vac
Report No.: RF160202D06-1 Page No. 15 / 65 Report Format Version:6.1.1
Mode B Power Line Conducted Emission Test
EUT
USB 3.0 Notebook PC (E) 1
USB 2.0
SD SD card (A)
USB Disk (B)
120Vac
2
Report No.: RF160202D06-1 Page No. 16 / 65 Report Format Version:6.1.1
3.5 General Description of Applied Standard
The EUT is a RF Product. According to the specifications of the manufacturer, it must comply with the
requirements of the following standards:
FCC Part 15, Subpart E (15.407)
KDB 789033 D02 General UNII Test Procedure New Rules v01r02
ANSI C63.10-2013
All test items have been performed and recorded as per the above standards.
NOTE: The EUT has been verified to comply with the requirements of FCC Part 15, Subpart B, Class B
(DoC). The test report has been issued separately.
Report No.: RF160202D06-1 Page No. 17 / 65 Report Format Version:6.1.1
4 Test Types and Results
4.1 Radiated Emission and Bandedge Measurement
4.1.1 Limits of Radiated Emission and Bandedge Measurement Radiated emissions which fall in the restricted bands must comply with the radiated emission limits specified as below table.
Frequencies (MHz)
Field Strength (microvolts/meter)
Measurement Distance (meters)
0.009 ~ 0.490 2400/F(kHz) 300
0.490 ~ 1.705 24000/F(kHz) 30
1.705 ~ 30.0 30 30
30 ~ 88 100 3
88 ~ 216 150 3
216 ~ 960 200 3
Above 960 500 3
NOTE:
1. The lower limit shall apply at the transition frequencies.
2. Emission level (dBuV/m) = 20 log Emission level (uV/m).
3. For frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation.
LIMITS OF UNWANTED EMISSION OUT OF THE RESTRICTED BANDS
APPLICABLE TO LIMIT
789033 D02 General UNII Test Procedure New Rules v01r02
FIELD STRENGTH AT 3m
PK:74 (dBµV/m) AV:54 (dBµV/m)
APPLICABLE TO EIRP LIMIT EQUIVALENT FIELD STRENGTH AT 3m
15.407(b)(1)
PK:-27 (dBm/MHz) PK:68.2(dBµV/m) 15.407(b)(2)
15.407(b)(3)
15.407(b)(4) PK:-27 (dBm/MHz)
*1
PK:-17 (dBm/MHz) *2
PK: 68.2(dBµV/m)
*1
PK:78.2 (dBµV/m) *2
NOTE: *1
beyond 10MHz of the band edge *2
within 10 MHz of band edge
The following formula is used to convert the equipment isotropic radiated power (eirp) to
field strength:
E = 3
301000000 P µV/m, where P is the eirp (Watts).
Report No.: RF160202D06-1 Page No. 18 / 65 Report Format Version:6.1.1
4.1.2 Test Instruments
DESCRIPTION &
MANUFACTURER MODEL NO. SERIAL NO.
CALIBRATED
DATE
CALIBRATED
UNTIL
HP Preamplifier 8447D 2432A03504 Feb. 26, 2015 Feb. 25, 2016
Feb. 26, 2016 Feb. 25, 2017
HP Preamplifier 8449B 3008A01201 Feb. 26, 2015 Feb. 25, 2016
Feb. 26, 2016 Feb. 25, 2017
MITEQ Preamplifier AMF-6F-260400-33-8P 892164 Mar. 01, 2015 Feb. 29, 2016
Mar. 01, 2016 Feb. 28, 2017
Agilent
TEST RECEIVER N9038A MY51210129 Feb. 02, 2016 Feb. 01, 2017
Schwarzbeck Antenna VULB 9168 139 Jan. 04, 2016 Jan. 03, 2017
Schwarzbeck Antenna VHBA 9123 480 May 29, 2015 May 28, 2017
Schwarzbeck Horn Antenna BBHA-9170 212 Jan. 08, 2016 Jan. 07, 2017
Schwarzbeck Horn Antenna BBHA 9120-D1 D130 Jan. 21, 2016 Jan. 20, 2017
ADT. Turn Table TT100 0306 NA NA
ADT. Tower AT100 0306 NA NA
Software Radiated_V7.6.15.9.4 NA NA NA
SUHNER RF cable
With 4dB PAD SF104 CABLE-CH6 Aug. 15, 2015 Aug. 14, 2016
SUHNER RF cable
With 3dB PAD SF102 Cable-CH8-3.6m Aug. 15, 2015 Aug. 14, 2016
KEYSIGHT MIMO
Powermeasurement Test set U2021XA U2021XA-001 May 04, 2015 May 03, 2016
KEYSIGHT
Spectrum Analyzer N9030A MY54490260 Jul. 14, 2015 Jul. 13, 2016
EMCO Horn Antenna 3115 00028257 Jan. 19, 2016 Jan. 18, 2017
Highpass filter
Wainwright Instruments WHK 3.1/18G-10SS SN 8 NA NA
ROHDE & SCHWARZ
Spectrum Analyzer FSV40 101042 Sep. 23, 2015 Sep. 22, 2016
Anritsu
Power Sensor MA2411B 0738404 Apr. 21, 2015 Apr. 20, 2016
Anritsu
Power Meter ML2495A 0842014 Apr. 21, 2015 Apr. 20, 2016
Temperature & Humidity
Chamber MHU-225AU 920409 May 25, 2015 May 24, 2016
Programable DC Source
IDRC DSP-030-025HD 500158 Jul. 17, 2015 Jul. 16, 2016
NOTE: 1. The calibration interval of the above test instruments is 12/24 months. And the calibrations are
traceable to NML/ROC and NIST/USA. 2. The horn antenna and HP preamplifier (model: 8449B) are used only for the measurement of
emission frequency above 1GHz if tested. 3. The test was performed in Chamber No. 6. 4. The Industry Canada Reference No. IC 7450E-6. 5. The FCC Site Registration No. is 447212.
Report No.: RF160202D06-1 Page No. 19 / 65 Report Format Version:6.1.1
4.1.3 Test Procedure a. The EUT was placed on the top of a rotating table 0.8 meters (for below 1GHz) / 1.5 meters (for above
1GHz) above the ground at 3 meter chamber room for test. The table was rotated 360 degrees to determine the position of the highest radiation.
b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower.
c. The height of antenna is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement.
d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading.
e. The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum hold mode when the test frequency is below 1 GHz.
f. The test-receiver system was set to peak and average detect function and specified bandwidth with maximum hold mode when the test frequency is above 1 GHz. If the peak reading value also meets average limit, measurement with the average detector is unnecessary.
Note: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for
Quasi-peak detection (QP) at frequency below 1GHz.
2. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 3 MHz for Peak detection (PK) at frequency above 1GHz.
3. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and the video bandwidth is 10Hz (Duty cycle ≥ 98%) for Average detection (AV) at frequency above 1GHz.
4. All modes of operation were investigated and the worst-case emissions are reported.
4.1.4 Deviation from Test Standard
No deviation.
Report No.: RF160202D06-1 Page No. 20 / 65 Report Format Version:6.1.1
4.1.5 Test Setup
<Frequency Range below 1GHz>
10m
Ant. Tower1-4m
Variable
Turn Table
EUT&
Support Units
Ground Plane
Test Receiver
80cm
<Frequency Range above 1GHz>
For the actual test configuration, please refer to the attached file (Test Setup Photo).
4.1.6 EUT Operating Condition
Connected the EUT to adapter
Set the EUT under transmission condition continuously at specific channel frequency.
3m
1-4m Variable
Turn Table
EUT& Support Units
Ground Plane
Test Receiver
150cm
Absorber
Ant. Tower
3m
Report No.: RF160202D06-1 Page No. 21 / 65 Report Format Version:6.1.1
4.1.7 Test Results
Mode A
BELOW 1GHz WORST-CASE DATA
802.11a
CHANNEL TX Channel 40 DETECTOR FUNCTION
Quasi-Peak (QP) FREQUENCY RANGE 30MHz ~ 1GHz
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 32.09 31.9 QP 40.0 -8.1 4.00 H 226 43.36 -11.42
2 77.14 25.2 QP 40.0 -14.8 4.00 H 256 38.50 -13.30
3 162.26 26.1 QP 43.5 -17.4 3.21 H 316 35.43 -9.31
4 528.05 30.3 QP 46.0 -15.7 1.96 H 174 33.24 -2.97
5 623.98 29.5 QP 46.0 -16.5 1.41 H 274 30.51 -0.99
6 814.05 31.7 QP 46.0 -14.3 1.00 H 0 29.72 1.95
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 32.62 31.7 QP 40.0 -8.4 1.27 V 77 42.91 -11.26
2 105.03 24.6 QP 43.5 -18.9 1.00 V 275 37.95 -13.37
3 337.44 24.1 QP 46.0 -21.9 1.55 V 247 31.21 -7.12
4 528.05 26.9 QP 46.0 -19.1 2.38 V 275 29.89 -2.97
5 730.10 30.3 QP 46.0 -15.7 2.97 V 170 29.93 0.35
6 893.06 32.5 QP 46.0 -13.5 2.41 V 124 29.66 2.86
REMARKS:
1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB)
3. The other emission levels were very low against the limit.
4. Margin value = Emission Level – Limit value
Report No.: RF160202D06-1 Page No. 22 / 65 Report Format Version:6.1.1
Mode A
ABOVE 1GHz DATA
802.11a
CHANNEL TX Channel 36 DETECTOR FUNCTION
Peak (PK)
Average (AV) FREQUENCY RANGE 1GHz ~ 40GHz
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 5150.00 60.3 PK 74.0 -13.7 3.48 H 209 51.77 8.53
2 5150.00 46.2 AV 54.0 -7.8 3.48 H 209 37.65 8.53
3 *5180.00 96.9 PK 3.48 H 209 88.20 8.71
4 *5180.00 87.2 AV 3.48 H 209 78.45 8.71
5 #10360.00 60.1 PK 74.0 -13.9 1.36 H 31 39.76 20.33
6 #10360.00 46.5 AV 54.0 -7.5 1.36 H 31 26.21 20.33
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 5150.00 61.1 PK 74.0 -12.9 3.01 V 340 52.61 8.53
2 5150.00 46.8 AV 54.0 -7.2 3.01 V 340 38.25 8.53
3 *5180.00 99.1 PK 3.01 V 340 90.43 8.71
4 *5180.00 89.6 AV 3.01 V 340 80.85 8.71
5 #10360.00 61.2 PK 74.0 -12.8 2.39 V 294 40.91 20.33
6 #10360.00 47.1 AV 54.0 -6.9 2.39 V 294 26.75 20.33
REMARKS:
1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB)
3. The other emission levels were very low against the limit.
4. Margin value = Emission Level – Limit value
5. " * ": Fundamental frequency.
6. " # ": The radiated frequency is out of the restricted band.
Report No.: RF160202D06-1 Page No. 23 / 65 Report Format Version:6.1.1
CHANNEL TX Channel 40 DETECTOR FUNCTION
Peak (PK)
Average (AV) FREQUENCY RANGE 1GHz ~ 40GHz
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 *5200.00 97.4 PK 1.48 H 210 88.61 8.82
2 *5200.00 87.9 AV 1.48 H 210 79.06 8.82
3 #10400.00 60.0 PK 74.0 -14.0 1.44 H 39 39.58 20.46
4 #10400.00 46.7 AV 54.0 -7.3 1.44 H 39 26.25 20.46
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 *5200.00 98.1 PK 3.00 V 347 89.32 8.82
2 *5200.00 88.2 AV 3.00 V 347 79.39 8.82
3 #10400.00 60.4 PK 74.0 -13.7 2.41 V 288 39.89 20.46
4 #10400.00 47.2 AV 54.0 -6.8 2.41 V 288 26.77 20.46
REMARKS:
1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB)
3. The other emission levels were very low against the limit.
4. Margin value = Emission Level – Limit value
5. " * ": Fundamental frequency.
6. " # ": The radiated frequency is out of the restricted band.
Report No.: RF160202D06-1 Page No. 24 / 65 Report Format Version:6.1.1
CHANNEL TX Channel 48 DETECTOR FUNCTION
Peak (PK)
Average (AV) FREQUENCY RANGE 1GHz ~ 40GHz
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 *5240.00 96.8 PK 1.21 H 206 87.87 8.97
2 *5240.00 86.7 AV 1.21 H 206 77.76 8.97
3 5350.00 61.3 PK 74.0 -12.7 1.21 H 206 51.83 9.43
4 5350.00 46.7 AV 54.0 -7.3 1.21 H 206 37.25 9.43
5 #10480.00 60.2 PK 74.0 -13.9 1.40 H 25 39.26 20.89
6 #10480.00 47.0 AV 54.0 -7.0 1.40 H 25 26.10 20.89
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 *5240.00 97.6 PK 2.98 V 26 88.63 8.97
2 *5240.00 88.6 AV 2.98 V 26 79.61 8.97
3 5350.00 61.6 PK 74.0 -12.4 2.98 V 26 52.17 9.43
4 5350.00 47.5 AV 54.0 -6.5 2.98 V 26 38.07 9.43
5 #10480.00 60.7 PK 74.0 -13.3 2.27 V 299 39.81 20.89
6 #10480.00 47.6 AV 54.0 -6.4 2.27 V 299 26.70 20.89
REMARKS:
1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB)
3. The other emission levels were very low against the limit.
4. Margin value = Emission Level – Limit value
5. " * ": Fundamental frequency.
6. " # ": The radiated frequency is out of the restricted band.
Report No.: RF160202D06-1 Page No. 25 / 65 Report Format Version:6.1.1
CHANNEL TX Channel 149 DETECTOR FUNCTION
Peak (PK)
Average (AV) FREQUENCY RANGE 1GHz ~ 40GHz
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 #5725.00 61.5 PK 74.0 -12.5 2.95 H 198 51.09 10.40
2 #5725.00 47.8 AV 54.0 -6.2 2.95 H 198 37.41 10.40
3 *5745.00 97.6 PK 2.95 H 198 87.24 10.35
4 *5745.00 88.0 AV 2.95 H 198 77.63 10.35
5 11490.00 60.9 PK 74.0 -13.2 1.62 H 60 38.59 22.26
6 11490.00 47.9 AV 54.0 -6.1 1.62 H 60 25.61 22.26
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 #5725.00 62.2 PK 74.0 -11.8 2.92 V 300 51.77 10.40
2 #5725.00 48.0 AV 54.0 -6.0 2.92 V 300 37.61 10.40
3 *5745.00 97.9 PK 2.92 V 300 87.54 10.35
4 *5745.00 88.2 AV 2.92 V 300 77.87 10.35
5 11490.00 61.3 PK 74.0 -12.8 2.38 V 227 38.99 22.26
6 11490.00 48.3 AV 54.0 -5.7 2.38 V 227 26.02 22.26
REMARKS:
1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB)
3. The other emission levels were very low against the limit.
4. Margin value = Emission Level – Limit value
5. " * ": Fundamental frequency.
6. " # ": The radiated frequency is out of the restricted band.
Report No.: RF160202D06-1 Page No. 26 / 65 Report Format Version:6.1.1
CHANNEL TX Channel 157 DETECTOR FUNCTION
Peak (PK)
Average (AV) FREQUENCY RANGE 1GHz ~ 40GHz
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 *5785.00 96.1 PK 2.89 H 204 85.82 10.26
2 *5785.00 87.0 AV 2.89 H 204 76.78 10.26
3 11570.00 61.1 PK 74.0 -12.9 1.51 H 66 38.73 22.35
4 11570.00 48.1 AV 54.0 -6.0 1.51 H 66 25.70 22.35
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 *5785.00 98.3 PK 3.93 V 283 88.00 10.26
2 *5785.00 89.0 AV 3.93 V 283 78.75 10.26
3 11570.00 61.4 PK 74.0 -12.6 2.40 V 230 39.06 22.35
4 11570.00 48.4 AV 54.0 -5.6 2.40 V 230 26.03 22.35
REMARKS:
1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB)
3. The other emission levels were very low against the limit.
4. Margin value = Emission Level – Limit value
5. " * ": Fundamental frequency.
Report No.: RF160202D06-1 Page No. 27 / 65 Report Format Version:6.1.1
CHANNEL TX Channel 165 DETECTOR FUNCTION
Peak (PK)
Average (AV) FREQUENCY RANGE 1GHz ~ 40GHz
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 *5825.00 96.5 PK 2.99 H 198 86.19 10.27
2 *5825.00 87.3 AV 2.99 H 198 77.02 10.27
3 #5850.00 61.5 PK 74.0 -12.6 2.99 H 198 51.16 10.29
4 #5850.00 47.7 AV 54.0 -6.3 2.99 H 198 37.43 10.29
5 11650.00 60.6 PK 74.0 -13.4 1.58 H 52 38.55 22.06
6 11650.00 47.8 AV 54.0 -6.3 1.58 H 52 25.69 22.06
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 *5825.00 99.2 PK 2.98 V 284 88.96 10.27
2 *5825.00 89.4 AV 2.98 V 284 79.12 10.27
3 #5850.00 62.9 PK 74.0 -11.1 2.98 V 284 52.58 10.29
4 #5850.00 48.8 AV 54.0 -5.2 2.98 V 284 38.47 10.29
5 11650.00 61.1 PK 74.0 -12.9 2.51 V 243 39.06 22.06
6 11650.00 48.0 AV 54.0 -6.0 2.51 V 243 25.98 22.06
REMARKS:
1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB)
3. The other emission levels were very low against the limit.
4. Margin value = Emission Level – Limit value
5. " * ": Fundamental frequency.
6. " # ": The radiated frequency is out of the restricted band.
Report No.: RF160202D06-1 Page No. 28 / 65 Report Format Version:6.1.1
802.11n (20MHz)
CHANNEL TX Channel 36 DETECTOR FUNCTION
Peak (PK)
Average (AV) FREQUENCY RANGE 1GHz ~ 40GHz
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 5150.00 60.9 PK 74.0 -13.1 1.50 H 209 52.41 8.53
2 5150.00 46.8 AV 54.0 -7.2 1.50 H 209 38.24 8.53
3 *5180.00 95.9 PK 1.50 H 209 87.16 8.71
4 *5180.00 85.6 AV 1.50 H 209 76.89 8.71
5 #10360.00 59.9 PK 74.0 -14.1 1.53 H 50 39.58 20.33
6 #10360.00 46.6 AV 54.0 -7.4 1.53 H 50 26.25 20.33
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 5150.00 61.5 PK 74.0 -12.5 3.00 V 341 52.97 8.53
2 5150.00 47.5 AV 54.0 -6.5 3.00 V 341 39.01 8.53
3 *5180.00 96.9 PK 3.00 V 341 88.16 8.71
4 *5180.00 87.4 AV 3.00 V 341 78.68 8.71
5 #10360.00 60.2 PK 74.0 -13.8 2.08 V 274 39.88 20.33
6 #10360.00 47.0 AV 54.0 -7.0 2.08 V 274 26.64 20.33
REMARKS:
1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB)
3. The other emission levels were very low against the limit.
4. Margin value = Emission Level – Limit value
5. " * ": Fundamental frequency.
6. " # ": The radiated frequency is out of the restricted band.
Report No.: RF160202D06-1 Page No. 29 / 65 Report Format Version:6.1.1
CHANNEL TX Channel 40 DETECTOR FUNCTION
Peak (PK)
Average (AV) FREQUENCY RANGE 1GHz ~ 40GHz
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 *5200.00 95.8 PK 3.03 H 186 86.95 8.82
2 *5200.00 86.3 AV 3.03 H 186 77.45 8.82
3 #10400.00 59.6 PK 74.0 -14.4 1.60 H 43 39.18 20.46
4 #10400.00 46.6 AV 54.0 -7.5 1.60 H 43 26.09 20.46
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 *5200.00 96.9 PK 3.59 V 338 88.06 8.82
2 *5200.00 87.3 AV 3.59 V 338 78.49 8.82
3 #10400.00 60.3 PK 74.0 -13.7 2.17 V 280 39.85 20.46
4 #10400.00 47.2 AV 54.0 -6.8 2.17 V 280 26.74 20.46
REMARKS:
1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB)
3. The other emission levels were very low against the limit.
4. Margin value = Emission Level – Limit value
5. " * ": Fundamental frequency.
6. " # ": The radiated frequency is out of the restricted band.
Report No.: RF160202D06-1 Page No. 30 / 65 Report Format Version:6.1.1
CHANNEL TX Channel 48 DETECTOR FUNCTION
Peak (PK)
Average (AV) FREQUENCY RANGE 1GHz ~ 40GHz
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 *5240.00 96.6 PK 1.31 H 210 87.58 8.97
2 *5240.00 86.2 AV 1.31 H 210 77.20 8.97
3 5350.00 60.6 PK 74.0 -13.4 1.31 H 210 51.16 9.43
4 5350.00 46.3 AV 54.0 -7.7 1.31 H 210 36.89 9.43
5 #10480.00 60.1 PK 74.0 -13.9 1.48 H 48 39.20 20.89
6 #10480.00 47.1 AV 54.0 -6.9 1.48 H 48 26.19 20.89
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 *5240.00 98.2 PK 2.81 V 340 89.26 8.97
2 *5240.00 88.1 AV 2.81 V 340 79.15 8.97
3 5350.00 61.5 PK 74.0 -12.5 2.81 V 340 52.07 9.43
4 5350.00 47.2 AV 54.0 -6.8 2.81 V 340 37.79 9.43
5 #10480.00 60.3 PK 74.0 -13.7 1.98 V 263 39.41 20.89
6 #10480.00 47.4 AV 54.0 -6.6 1.98 V 263 26.50 20.89
REMARKS:
1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB)
3. The other emission levels were very low against the limit.
4. Margin value = Emission Level – Limit value
5. " * ": Fundamental frequency.
6. " # ": The radiated frequency is out of the restricted band.
Report No.: RF160202D06-1 Page No. 31 / 65 Report Format Version:6.1.1
CHANNEL TX Channel 149 DETECTOR FUNCTION
Peak (PK)
Average (AV) FREQUENCY RANGE 1GHz ~ 40GHz
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 #5725.00 61.3 PK 74.0 -12.7 2.70 H 198 50.86 10.40
2 #5725.00 47.8 AV 54.0 -6.2 2.70 H 198 37.36 10.40
3 *5745.00 96.9 PK 2.70 H 198 86.59 10.35
4 *5745.00 86.8 AV 2.70 H 198 76.49 10.35
5 11490.00 61.2 PK 74.0 -12.8 1.35 H 88 38.97 22.26
6 11490.00 48.1 AV 54.0 -5.9 1.35 H 88 25.80 22.26
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 #5725.00 62.7 PK 74.0 -11.4 2.58 V 285 52.25 10.40
2 #5725.00 49.0 AV 54.0 -5.0 2.58 V 285 38.58 10.40
3 *5745.00 99.0 PK 2.58 V 285 88.65 10.35
4 *5745.00 88.9 AV 2.58 V 285 78.55 10.35
5 11490.00 61.4 PK 74.0 -12.6 2.77 V 289 39.18 22.26
6 11490.00 48.4 AV 54.0 -5.7 2.77 V 289 26.09 22.26
REMARKS:
1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB)
3. The other emission levels were very low against the limit.
4. Margin value = Emission Level – Limit value
5. " * ": Fundamental frequency.
6. " # ": The radiated frequency is out of the restricted band.
Report No.: RF160202D06-1 Page No. 32 / 65 Report Format Version:6.1.1
CHANNEL TX Channel 157 DETECTOR FUNCTION
Peak (PK)
Average (AV) FREQUENCY RANGE 1GHz ~ 40GHz
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 *5785.00 95.2 PK 3.03 H 201 84.93 10.26
2 *5785.00 86.1 AV 3.03 H 201 75.84 10.26
3 11570.00 61.3 PK 74.0 -12.8 1.28 H 91 38.90 22.35
4 11570.00 48.2 AV 54.0 -5.8 1.28 H 91 25.84 22.35
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 *5785.00 98.2 PK 3.16 V 283 87.97 10.26
2 *5785.00 88.1 AV 3.16 V 283 77.81 10.26
3 11570.00 61.7 PK 74.0 -12.3 2.69 V 283 39.31 22.35
4 11570.00 48.5 AV 54.0 -5.5 2.69 V 283 26.14 22.35
REMARKS:
1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB)
3. The other emission levels were very low against the limit.
4. Margin value = Emission Level – Limit value
5. " * ": Fundamental frequency.
Report No.: RF160202D06-1 Page No. 33 / 65 Report Format Version:6.1.1
CHANNEL TX Channel 165 DETECTOR FUNCTION
Peak (PK)
Average (AV) FREQUENCY RANGE 1GHz ~ 40GHz
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 *5825.00 95.6 PK 2.88 H 199 85.31 10.27
2 *5825.00 86.0 AV 2.88 H 199 75.69 10.27
3 #5850.00 61.9 PK 74.0 -12.1 2.88 H 199 51.63 10.29
4 #5850.00 47.6 AV 54.0 -6.4 2.88 H 199 37.34 10.29
5 11650.00 60.8 PK 74.0 -13.2 1.00 H 58 38.74 22.06
6 11650.00 47.9 AV 54.0 -6.1 1.00 H 58 25.80 22.06
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 *5825.00 97.8 PK 3.55 V 287 87.53 10.27
2 *5825.00 87.5 AV 3.55 V 287 77.18 10.27
3 #5850.00 63.1 PK 74.0 -10.9 3.55 V 287 52.77 10.29
4 #5850.00 47.8 AV 54.0 -6.2 3.55 V 287 37.55 10.29
5 11650.00 61.1 PK 74.0 -12.9 2.59 V 275 39.08 22.06
6 11650.00 48.2 AV 54.0 -5.8 2.59 V 275 26.14 22.06
REMARKS:
1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB)
3. The other emission levels were very low against the limit.
4. Margin value = Emission Level – Limit value
5. " * ": Fundamental frequency.
6. " # ": The radiated frequency is out of the restricted band.
Report No.: RF160202D06-1 Page No. 34 / 65 Report Format Version:6.1.1
802.11n (40MHz)
CHANNEL TX Channel 38 DETECTOR FUNCTION
Peak (PK)
Average (AV) FREQUENCY RANGE 1GHz ~ 40GHz
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 5150.00 60.5 PK 74.0 -13.5 2.62 H 184 51.99 8.53
2 5150.00 46.0 AV 54.0 -8.0 2.62 H 184 37.49 8.53
3 *5190.00 94.1 PK 2.62 H 184 85.32 8.77
4 *5190.00 83.6 AV 2.62 H 184 74.78 8.77
5 #10380.00 59.5 PK 74.0 -14.5 1.44 H 73 39.10 20.40
6 #10380.00 46.5 AV 54.0 -7.5 1.44 H 73 26.07 20.40
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 5150.00 61.2 PK 74.0 -12.8 3.00 V 341 52.68 8.53
2 5150.00 46.8 AV 54.0 -7.2 3.00 V 341 38.27 8.53
3 *5190.00 95.7 PK 3.00 V 341 86.94 8.77
4 *5190.00 85.4 AV 3.00 V 341 76.63 8.77
5 #10380.00 59.7 PK 74.0 -14.3 2.90 V 268 39.28 20.40
6 #10380.00 46.6 AV 54.0 -7.4 2.90 V 268 26.24 20.40
REMARKS:
1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB)
3. The other emission levels were very low against the limit.
4. Margin value = Emission Level – Limit value
5. " * ": Fundamental frequency.
6. " # ": The radiated frequency is out of the restricted band.
Report No.: RF160202D06-1 Page No. 35 / 65 Report Format Version:6.1.1
CHANNEL TX Channel 46 DETECTOR FUNCTION
Peak (PK)
Average (AV) FREQUENCY RANGE 1GHz ~ 40GHz
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 *5230.00 94.9 PK 2.84 H 185 85.92 8.94
2 *5230.00 84.5 AV 2.84 H 185 75.52 8.94
3 5350.00 60.7 PK 74.0 -13.3 2.84 H 185 51.28 9.43
4 5350.00 46.5 AV 54.0 -7.5 2.84 H 185 37.04 9.43
5 #10460.00 59.9 PK 74.0 -14.1 1.41 H 69 39.08 20.79
6 #10460.00 46.8 AV 54.0 -7.2 1.41 H 69 26.00 20.79
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 *5230.00 95.6 PK 3.59 V 340 86.61 8.94
2 *5230.00 85.0 AV 3.59 V 340 76.09 8.94
3 5350.00 61.7 PK 74.0 -12.3 3.59 V 340 52.26 9.43
4 5350.00 47.3 AV 54.0 -6.7 3.59 V 340 37.89 9.43
5 #10460.00 60.0 PK 74.0 -14.0 2.84 V 273 39.21 20.79
6 #10460.00 47.0 AV 54.0 -7.0 2.84 V 273 26.18 20.79
REMARKS:
1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB)
3. The other emission levels were very low against the limit.
4. Margin value = Emission Level – Limit value
5. " * ": Fundamental frequency.
6. " # ": The radiated frequency is out of the restricted band.
Report No.: RF160202D06-1 Page No. 36 / 65 Report Format Version:6.1.1
CHANNEL TX Channel 151 DETECTOR FUNCTION
Peak (PK)
Average (AV) FREQUENCY RANGE 1GHz ~ 40GHz
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 #5725.00 62.0 PK 74.0 -12.1 2.69 H 201 51.55 10.40
2 #5725.00 48.1 AV 54.0 -5.9 2.69 H 201 37.69 10.40
3 *5755.00 96.5 PK 2.69 H 201 86.15 10.34
4 *5755.00 86.6 AV 2.69 H 201 76.30 10.34
5 11510.00 61.3 PK 74.0 -12.7 1.46 H 73 38.97 22.29
6 11510.00 48.2 AV 54.0 -5.8 1.46 H 73 25.88 22.29
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 #5725.00 62.7 PK 74.0 -11.3 3.03 V 288 52.31 10.40
2 #5725.00 48.4 AV 54.0 -5.6 3.03 V 288 37.98 10.40
3 *5755.00 97.6 PK 3.03 V 288 87.21 10.34
4 *5755.00 87.6 AV 3.03 V 288 77.21 10.34
5 11510.00 61.5 PK 74.0 -12.5 2.39 V 277 39.20 22.29
6 11510.00 48.4 AV 54.0 -5.6 2.39 V 277 26.13 22.29
REMARKS:
1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB)
3. The other emission levels were very low against the limit.
4. Margin value = Emission Level – Limit value
5. " * ": Fundamental frequency.
6. " # ": The radiated frequency is out of the restricted band.
Report No.: RF160202D06-1 Page No. 37 / 65 Report Format Version:6.1.1
CHANNEL TX Channel 159 DETECTOR FUNCTION
Peak (PK)
Average (AV) FREQUENCY RANGE 1GHz ~ 40GHz
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 *5795.00 96.4 PK 2.90 H 197 86.15 10.24
2 *5795.00 86.4 AV 2.90 H 197 76.18 10.24
3 #5850.00 61.3 PK 74.0 -12.7 2.90 H 197 51.01 10.29
4 #5850.00 47.7 AV 54.0 -6.3 2.90 H 197 37.40 10.29
5 11590.00 61.4 PK 74.0 -12.6 1.41 H 68 38.99 22.37
6 11590.00 48.3 AV 54.0 -5.7 1.41 H 68 25.91 22.37
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 *5795.00 97.5 PK 3.01 V 282 87.26 10.24
2 *5795.00 88.6 AV 3.01 V 282 78.33 10.24
3 #5850.00 62.4 PK 74.0 -11.6 3.01 V 282 52.13 10.29
4 #5850.00 49.8 AV 54.0 -4.2 3.01 V 282 39.51 10.29
5 11590.00 61.5 PK 74.0 -12.5 2.31 V 287 39.14 22.37
6 11590.00 48.6 AV 54.0 -5.5 2.31 V 287 26.18 22.37
REMARKS:
1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB)
3. The other emission levels were very low against the limit.
4. Margin value = Emission Level – Limit value
5. " * ": Fundamental frequency.
6. " # ": The radiated frequency is out of the restricted band.
Report No.: RF160202D06-1 Page No. 38 / 65 Report Format Version:6.1.1
802.11ac 80MHz
CHANNEL TX Channel 42 DETECTOR FUNCTION
Peak (PK)
Average (AV) FREQUENCY RANGE 1GHz ~ 40GHz
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 5150.00 60.8 PK 74.0 -13.2 2.69 H 210 52.28 8.53
2 5150.00 46.6 AV 54.0 -7.4 2.69 H 210 38.04 8.53
3 *5210.00 88.2 PK 2.69 H 210 79.35 8.86
4 *5210.00 77.8 AV 2.69 H 210 68.98 8.86
5 5350.00 61.4 PK 74.0 -12.6 2.69 H 210 51.99 9.43
6 5350.00 46.5 AV 54.0 -7.5 2.69 H 210 37.08 9.43
7 #10420.00 59.8 PK 74.0 -14.3 1.18 H 52 39.17 20.58
8 #10420.00 46.6 AV 54.0 -7.4 1.18 H 52 25.98 20.58
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 5150.00 61.8 PK 74.0 -12.2 3.59 V 340 53.23 8.53
2 5150.00 47.2 AV 54.0 -6.9 3.59 V 340 38.62 8.53
3 *5210.00 89.3 PK 3.59 V 340 80.45 8.86
4 *5210.00 78.8 AV 3.59 V 340 69.90 8.86
5 5350.00 61.8 PK 74.0 -12.2 3.59 V 340 52.34 9.43
6 5350.00 47.3 AV 54.0 -6.7 3.59 V 340 37.89 9.43
7 #10420.00 60.0 PK 74.0 -14.0 2.49 V 300 39.40 20.58
8 #10420.00 46.7 AV 54.0 -7.3 2.49 V 300 26.11 20.58
REMARKS:
1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB)
3. The other emission levels were very low against the limit.
4. Margin value = Emission Level – Limit value
5. " * ": Fundamental frequency.
6. " # ": The radiated frequency is out of the restricted band.
Report No.: RF160202D06-1 Page No. 39 / 65 Report Format Version:6.1.1
CHANNEL TX Channel 155 DETECTOR FUNCTION
Peak (PK)
Average (AV) FREQUENCY RANGE 1GHz ~ 40GHz
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 #5725.00 63.1 PK 74.0 -10.9 1.11 H 203 52.70 10.40
2 #5725.00 48.1 AV 54.0 -5.9 1.11 H 203 37.72 10.40
3 *5775.00 92.0 PK 1.11 H 203 81.69 10.29
4 *5775.00 81.3 AV 1.11 H 203 71.05 10.29
5 #5850.00 63.0 PK 74.0 -11.0 1.11 H 203 52.67 10.29
6 #5850.00 48.8 AV 54.0 -5.2 1.11 H 203 38.54 10.29
7 11550.00 61.6 PK 74.0 -12.4 1.57 H 84 39.25 22.33
8 11550.00 48.2 AV 54.0 -5.8 1.57 H 84 25.83 22.33
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
NO. FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1 #5725.00 64.0 PK 74.0 -10.0 3.01 V 300 53.58 10.40
2 #5725.00 48.8 AV 54.0 -5.2 3.01 V 300 38.44 10.40
3 *5775.00 92.3 PK 3.01 V 300 82.04 10.29
4 *5775.00 81.9 AV 3.01 V 300 71.60 10.29
5 #5850.00 63.3 PK 74.0 -10.7 3.01 V 300 53.05 10.29
6 #5850.00 49.4 AV 54.0 -4.7 3.01 V 300 39.06 10.29
7 11550.00 61.7 PK 74.0 -12.3 2.17 V 284 39.37 22.33
8 11550.00 48.4 AV 54.0 -5.7 2.17 V 284 26.02 22.33
REMARKS:
1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB)
3. The other emission levels were very low against the limit.
4. Margin value = Emission Level – Limit value
5. " * ": Fundamental frequency.
6. " # ": The radiated frequency is out of the restricted band.
Report No.: RF160202D06-1 Page No. 40 / 65 Report Format Version:6.1.1
4.2 Conducted Emission Measurement
4.2.1 Limits of Conducted Emission Measurement
Frequency (MHz) Conducted Limit (dBuV)
Quasi-peak Average
0.15 - 0.5 66 - 56 56 - 46
0.50 - 5.0 56 46
5.0 - 30.0 60 50
Note: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50MHz.
4.2.2 Test Instruments
Description & Manufacturer Model No. Serial No. Cal. Date Cal. Due
ROHDE & SCHWARZ
TEST RECEIVER ESCS 30 100276 Apr. 01, 2015 Mar. 31, 2016
ROHDE & SCHWARZ
Artificial Mains Network
(for EUT)
ENV216 101197 Apr. 27, 2015 Apr. 26, 2016
LISN With Adapter
(for EUT) AD10 C10Ada-002 Apr. 27, 2015 Apr. 26, 2016
ROHDE & SCHWARZ
Artificial Mains Network
(for peripherals)
ESH3-Z5 100218 Nov. 25, 2015 Nov. 24, 2016
SCHWARZBECK
Artificial Mains Network (For
EUT)
NNLK8129 8129229 May 06, 2015 May 05, 2016
Software Cond_V7.3.7 NA NA NA
RF cable (JYEBAO)
With 10dB PAD 5D-FB Cable-C10.01 Feb. 15, 2016 Feb. 14, 2017
SUHNER Terminator
(For ROHDE & SCHWARZ
LISN)
65BNC-5001 E1-011484 May 19, 2015 May 18, 2016
ROHDE & SCHWARZ
Artificial Mains Network (For
TV EUT)
ESH3-Z5 100220 Nov. 13, 2015 Nov. 12, 2016
LISN With Adapter
(for TV EUT) 100220 N/A Nov. 13, 2015 Nov. 12, 2016
Notes: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA.
2. The test was performed in Shielded Room No. 10. 3. The VCCI Site Registration No. C-1852.
Report No.: RF160202D06-1 Page No. 41 / 65 Report Format Version:6.1.1
4.2.3 Test Procedure
a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50uH of coupling impedance for the measuring instrument.
b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference.
c. The frequency range from 150kHz to 30MHz was searched. Emission levels under (Limit - 20dB) was not recorded.
NOTE: All modes of operation were investigated and the worst-case emissions are reported.
4.2.4 Deviation from Test Standard No deviation.
4.2.5 Test Setup
Note: 1.Support units were connected to second LISN.
2.Both of LISNs (AMN) are 80 cm from EUT and at least 80
from other units and other metal planes
Vertical Ground
Reference Plane
40cm
80cm
Test Receiver
Horizontal Ground
Reference Plane
EUT
LISN
For the actual test configuration, please refer to the attached file (Test Setup Photo).
4.2.6 EUT Operating Condition
Mode A
Connected the EUT to adapter
Set the EUT under transmission condition continuously at specific channel frequency.
Mode B
a. Turned on the power of all equipmen
b. Connected the EUT to Notebook via USB 3.0 cable
c. Notebook read and wrote messages from EUT.
Report No.: RF160202D06-1 Page No. 42 / 65 Report Format Version:6.1.1
4.2.7 Test Results
Mode A
802.11a: CH40
Phase Line (L) Detector Function Quasi-Peak (QP) / Average (AV)
No Frequency
Correction
Factor Reading Value
(dBuV) Emission Level
(dBuV) Limit
(dBuV) Margin
(dB)
(MHz) (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV.
1 0.15001 9.66 36.91 22.48 46.57 32.14 66.00 56.00 -19.43 -23.86
2 0.41953 9.68 33.31 22.05 42.99 31.73 57.46 47.46 -14.46 -15.72
3 0.90000 9.75 27.71 15.18 37.46 24.93 56.00 46.00 -18.54 -21.07
4 2.75391 9.92 29.33 21.51 39.25 31.43 56.00 46.00 -16.75 -14.57
5 4.30859 10.01 28.03 18.97 38.04 28.98 56.00 46.00 -17.96 -17.02
6 6.57813 10.05 23.56 15.53 33.61 25.58 60.00 50.00 -26.39 -24.42
Remarks:
1. Q.P. and AV. are abbreviations of quasi-peak and average individually.
2. The emission levels of other frequencies were very low against the limit.
3. Margin value = Emission level – Limit value
4. Correction factor = Insertion loss + Cable loss
5. Emission Level = Correction Factor + Reading Value
Report No.: RF160202D06-1 Page No. 43 / 65 Report Format Version:6.1.1
Phase Neutral (N) Detector Function Quasi-Peak (QP) / Average (AV)
No Frequency
Correction
Factor Reading Value
(dBuV) Emission Level
(dBuV) Limit
(dBuV) Margin
(dB)
(MHz) (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV.
1 0.16562 9.69 37.72 23.23 47.41 32.92 65.18 55.18 -17.77 -22.26
2 0.32578 9.71 30.35 19.79 40.06 29.50 59.56 49.56 -19.50 -20.06
3 0.42344 9.72 31.03 20.18 40.75 29.90 57.38 47.38 -16.63 -17.48
4 0.92344 9.79 23.96 11.68 33.75 21.47 56.00 46.00 -22.25 -24.53
5 2.92969 9.99 25.38 16.03 35.37 26.02 56.00 46.00 -20.63 -19.98
6 5.52734 10.13 22.63 13.27 32.76 23.40 60.00 50.00 -27.24 -26.60
Remarks:
1. Q.P. and AV. are abbreviations of quasi-peak and average individually.
2. The emission levels of other frequencies were very low against the limit.
3. Margin value = Emission level – Limit value
4. Correction factor = Insertion loss + Cable loss
5. Emission Level = Correction Factor + Reading Value
Report No.: RF160202D06-1 Page No. 44 / 65 Report Format Version:6.1.1
Mode B
Phase Line (L) Detector Function Quasi-Peak (QP) / Average (AV)
No Frequency
Correction
Factor Reading Value
(dBuV) Emission Level
(dBuV) Limit
(dBuV) Margin
(dB)
(MHz) (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV.
1 0.16172 9.66 14.14 2.85 23.80 12.51 65.38 55.38 -41.58 -42.87
2 0.40391 9.64 19.91 19.10 29.55 28.74 57.77 47.77 -28.22 -19.03
3 0.43906 9.64 16.60 15.03 26.24 24.67 57.08 47.08 -30.84 -22.41
4 0.55625 9.65 12.37 3.26 22.02 12.91 56.00 46.00 -33.98 -33.09
5 1.79688 9.72 18.86 12.25 28.58 21.97 56.00 46.00 -27.42 -24.03
6 15.94531 9.93 10.41 6.30 20.34 16.23 60.00 50.00 -39.66 -33.77
Remarks:
1. Q.P. and AV. are abbreviations of quasi-peak and average individually.
2. The emission levels of other frequencies were very low against the limit.
3. Margin value = Emission level – Limit value
4. Correction factor = Insertion loss + Cable loss
5. Emission Level = Correction Factor + Reading Value
Report No.: RF160202D06-1 Page No. 45 / 65 Report Format Version:6.1.1
Phase Neutral (N) Detector Function Quasi-Peak (QP) / Average (AV)
No Frequency
Correction
Factor Reading Value
(dBuV) Emission Level
(dBuV) Limit
(dBuV) Margin
(dB)
(MHz) (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV.
1 0.27891 9.69 20.82 17.99 30.51 27.68 60.85 50.85 -30.34 -23.17
2 0.43906 9.68 18.33 16.60 28.01 26.28 57.08 47.08 -29.07 -20.80
3 0.93125 9.72 17.64 8.86 27.36 18.58 56.00 46.00 -28.64 -27.42
4 2.42969 9.78 18.63 11.37 28.41 21.15 56.00 46.00 -27.59 -24.85
5 7.60938 9.89 13.73 7.75 23.62 17.64 60.00 50.00 -36.38 -32.36
6 17.91016 10.02 12.56 6.90 22.58 16.92 60.00 50.00 -37.42 -33.08
Remarks:
1. Q.P. and AV. are abbreviations of quasi-peak and average individually.
2. The emission levels of other frequencies were very low against the limit.
3. Margin value = Emission level – Limit value
4. Correction factor = Insertion loss + Cable loss
5. Emission Level = Correction Factor + Reading Value
Report No.: RF160202D06-1 Page No. 46 / 65 Report Format Version:6.1.1
4.3 Transmit Power Measurment
4.3.1 Limits of Transmit Power Measurement
Operation Band
EUT Category LIMIT
U-NII-1
Outdoor Access Point
1 Watt (30 dBm) (Max. e.i.r.p ≦ 125mW(21 dBm) at any
elevation angle above 30 degrees as measured from the horizon)
Fixed point-to-point Access Point
1 Watt (30 dBm)
Indoor Access Point 1 Watt (30 dBm)
√ Mobile and Portable client
device 250mW (24 dBm)
U-NII-2A --- 250mW (24 dBm) or 11 dBm+10 log B*
U-NII-2C --- 250mW (24 dBm) or 11 dBm+10 log B*
U-NII-3 √ 1 Watt (30 dBm)
*B is the 26 dB emission bandwidth in megahertz
Per KDB 662911 Method of conducted output power measurement on IEEE 802.11 devices,
Array Gain = 0 dB (i.e., no array gain) for NANT ≤ 4; Array Gain = 0 dB (i.e., no array gain) for channel widths ≥ 40 MHz for any NANT; Array Gain = 5 log(NANT/NSS) dB or 3 dB, whichever is less for 20-MHz channel widths with NANT ≥ 5.
For power measurements on all other devices: Array Gain = 10 log(NANT/NSS) dB.
4.3.2 Test Setup FOR POWER OUTPUT MEASUREMENT
FOR 26dB & OCCUPIED BANDWIDTH
4.3.3 Test Instruments
Refer to section 4.1.2 to get information of above instrument.
EUT
Power Sensor
EUT SPECTRUM
ANALYZER
10dB ATTENUATION
PAD
10dB ATTENUATION
PAD
Power Meter
Report No.: RF160202D06-1 Page No. 47 / 65 Report Format Version:6.1.1
4.3.4 Test Procedure FOR AVERAGE POWER MEASUREMENT
Method PM is used to perform output power measurement, trigger and gating function of wide band power meter is enabled to measure max output power of TX on burst. Duty factor is not added to measured value. FOR 26 BANDWIDTH 1) Set RBW = approximately 1% of the emission bandwidth. 2) Set the VBW > RBW. 3) Detector = Peak. 4) Trace mode = max hold. 5) Measure the maximum width of the emission that is 26 dB down from the peak of the emission. Compare
this with the RBW setting of the analyzer. Readjust RBW and repeat measurement as needed until the RBW/EBW ratio is approximately 1%.
FOR OCCUPIED BANDWIDTH
The transmitter output was connected to the spectrum analyzer through an attenuator. The bandwidth of the fundamental frequency was measured by spectrum analyzer with resolution bandwidth in the range of 1% to 5% of the anticipated emission bandwidth, and a video bandwidth at least 3x the resolution bandwidth and set the detector to AVERAGE. The width of a frequency band such that, below the lower and above the upper frequency limits, the mean powers emitted are each equal to a specified percentage 0.5 %of the total mean power of a given emission.
4.3.5 Deviation from Test Standard
No deviation.
4.3.6 EUT Operating Condition
The software provided by client to enable the EUT under transmission condition continuously at lowest, middle and highest channel frequencies individually.
Report No.: RF160202D06-1 Page No. 48 / 65 Report Format Version:6.1.1
4.3.7 Test Result
POWER OUTPUT:
802.11a
CHANNEL
CHANNEL
FREQUENCY
(MHz)
MAXIMUM
CONDUCTED
POWER (mW)
MAXIMUM
CONDUCTED
POWER (dBm)
POWER LIMIT
(dBm) PASS/FAIL
36 5180 10.617 10.26 24 PASS
40 5200 10.593 10.25 24 PASS
48 5240 10.52 10.22 24 PASS
149 5745 10.765 10.32 24 PASS
157 5785 10.74 10.31 24 PASS
165 5825 10.691 10.29 24 PASS
802.11n (HT20)
CHANNEL
CHANNEL
FREQUENCY
(MHz)
MAXIMUM
CONDUCTED
POWER (mW)
MAXIMUM
CONDUCTED
POWER (dBm)
POWER LIMIT
(dBm) PASS/FAIL
36 5180 8.166 9.12 24 PASS
40 5200 8.279 9.18 24 PASS
48 5240 8.241 9.16 24 PASS
149 5745 8.299 9.19 24 PASS
157 5785 8.241 9.16 24 PASS
165 5825 8.147 9.11 24 PASS
802.11n (HT40)
CHANNEL
CHANNEL
FREQUENCY
(MHz)
MAXIMUM
CONDUCTED
POWER (mW)
MAXIMUM
CONDUCTED
POWER (dBm)
POWER LIMIT
(dBm) PASS/FAIL
38 5190 8.204 9.14 24 PASS
46 5230 8.26 9.17 24 PASS
151 5755 8.299 9.19 24 PASS
159 5795 8.337 9.21 24 PASS
802.11ac (VHT80)
CHANNEL
CHANNEL
FREQUENCY
(MHz)
MAXIMUM
CONDUCTED
POWER (mW)
MAXIMUM
CONDUCTED
POWER (dBm)
POWER LIMIT
(dBm) PASS/FAIL
42 5210 6.592 8.19 24 PASS
155 5775 6.622 8.21 24 PASS
Report No.: RF160202D06-1 Page No. 49 / 65 Report Format Version:6.1.1
26dB BANDWIDTH:
802.11a
CHANNEL CHANNEL
FREQUENCY (MHz)
26dBc BANDWIDTH (MHz) PASS / FAIL
36 5180 21.46 PASS
40 5200 21.51 PASS
48 5240 21.53 PASS
802.11n (HT20)
CHANNEL CHANNEL
FREQUENCY (MHz)
26dBc BANDWIDTH (MHz) PASS / FAIL
36 5180 22.10 PASS
40 5200 21.98 PASS
48 5240 22.11 PASS
802.11n (HT40)
CHANNEL CHANNEL
FREQUENCY (MHz)
26dBc BANDWIDTH (MHz) PASS / FAIL
38 5190 44.22 PASS
46 5230 44.44 PASS
802.11ac (VHT80)
CHANNEL CHANNEL
FREQUENCY (MHz)
26dBc BANDWIDTH (MHz) PASS / FAIL
42 5210 83.34 PASS
Report No.: RF160202D06-1 Page No. 50 / 65 Report Format Version:6.1.1
SPECTRUM PLOT OF WORST VALUE
802.11a 802.11n (HT20)
802.11n (HT40) 802.11ac (VHT80)
Report No.: RF160202D06-1 Page No. 51 / 65 Report Format Version:6.1.1
OCCUPIED BANDWIDTH:
802.11a
CHANNEL CHANNEL
FREQUENCY (MHz)
OCCUPIED BANDWIDTH (MHz) PASS / FAIL
36 5180 16.80 PASS
40 5200 16.80 PASS
48 5240 16.80 PASS
149 5745 16.78 PASS
157 5785 16.80 PASS
165 5825 16.80 PASS
802.11n (HT20)
CHANNEL CHANNEL
FREQUENCY (MHz)
OCCUPIED BANDWIDTH (MHz) PASS / FAIL
36 5180 17.88 PASS
40 5200 17.88 PASS
48 5240 17.88 PASS
149 5745 17.90 PASS
157 5785 17.80 PASS
165 5825 17.80 PASS
802.11n (HT40)
CHANNEL CHANNEL
FREQUENCY (MHz)
OCCUPIED BANDWIDTH (MHz) PASS / FAIL
38 5190 37.40 PASS
46 5230 37.20 PASS
151 5755 37.25 PASS
159 5795 37.17 PASS
802.11ac (VHT80)
CHANNEL CHANNEL
FREQUENCY (MHz)
OCCUPIED BANDWIDTH (MHz) PASS / FAIL
42 5210 75.36 PASS
155 5775 75.13 PASS
Report No.: RF160202D06-1 Page No. 52 / 65 Report Format Version:6.1.1
SPECTRUM PLOT OF WORST VALUE
802.11a 802.11n (HT20)
802.11n (HT40) 802.11ac (VHT80)
Report No.: RF160202D06-1 Page No. 53 / 65 Report Format Version:6.1.1
4.4 Peak Power Spectral Density Measurement
4.4.1 Limits of Peak Power Spectral Density Measurement
4.4.2 Test Setup
4.4.3 Test Instruments
Refer to section 4.1.2 to get information of above instrument.
4.4.4 Test Procedure
For U-NII-1 band:
Using method SA-1 1) Set span to encompass the entire emission bandwidth (EBW) of the signal. 2) Set RBW = 1 MHz, Set VBW ≥ 3 MHz, Detector = RMS 3) Sweep time = auto, trigger set to “free run”. 4) Trace average at least 100 traces in power averaging mode. 5) Record the max value For U-NII-3 band:
1) Set span to encompass the entire emission bandwidth (EBW) of the signal. 2) Set RBW = 500 kHz, Set VBW ≥ 3 RBW, Detector = RMS 3) Sweep time = auto, trigger set to “free run”. 4) Trace average at least 100 traces in power averaging mode. 5) Record the max value
Operation Band EUT Category LIMIT
U-NII-1 Outdoor Access Point
17dBm/ MHz Fixed point-to-point
Access Point
Indoor Access Point
√ Mobile and Portable
client device 11dBm/ MHz
U-NII-2A --- 11dBm/ MHz
U-NII-2C --- 11dBm/ MHz
U-NII-3 √ 30dBm/ 500kHz
EUT SPECTRUM ANALYZER
10dB ATTENUATION
PAD
Report No.: RF160202D06-1 Page No. 54 / 65 Report Format Version:6.1.1
4.4.5 Deviation from Test Standard
No deviation.
4.4.6 EUT Operating Condition
Same as Item 4.3.6.
Report No.: RF160202D06-1 Page No. 55 / 65 Report Format Version:6.1.1
4.4.7 Test Results For U-NII-1 Band
802.11a
CHANNEL FREQUENCY (MHz) PSD (dBm) MAXIMUM LIMIT
(dBm) PASS/FAIL
36 5180 -2.29 11 PASS
40 5200 -1.98 11 PASS
48 5240 -1.98 11 PASS
802.11n (HT20)
CHANNEL FREQUENCY (MHz) PSD (dBm) MAXIMUM LIMIT
(dBm) PASS/FAIL
36 5180 -3.44 11 PASS
40 5200 -3.12 11 PASS
48 5240 -2.96 11 PASS
802.11n (HT40)
CHANNEL FREQUENCY (MHz) PSD (dBm) MAXIMUM LIMIT
(dBm) PASS/FAIL
38 5190 -5.16 11 PASS
46 5230 -5.38 11 PASS
802.11ac (VHT80)
CHANNEL FREQUENCY (MHz) PSD (dBm) MAXIMUM LIMIT
(dBm) PASS/FAIL
42 5210 -10.74 11 PASS
Report No.: RF160202D06-1 Page No. 56 / 65 Report Format Version:6.1.1
SPECTRUM PLOT OF WORST VALUE
802.11a 802.11n (HT20)
802.11n (HT40) 802.11ac (VHT80)
Report No.: RF160202D06-1 Page No. 57 / 65 Report Format Version:6.1.1
For U-NII-3 Band
802.11a
Channel Freq. (MHz)
PSD (dBm/500kHz)
Limit (dBm/500kHz)
PASS /FAIL
149 5745 3.40 30 PASS
157 5785 3.00 30 PASS
165 5825 3.21 30 PASS
802.11n (HT20)
Channel Freq. (MHz)
PSD (dBm/500kHz)
Limit (dBm/500kHz)
PASS /FAIL
149 5745 2.36 30 PASS
157 5785 1.41 30 PASS
165 5825 1.80 30 PASS
802.11n (HT40)
Channel Freq. (MHz)
PSD (dBm/500kHz)
Limit (dBm/500kHz)
PASS /FAIL
151 5755 1.22 30 PASS
159 5795 1.09 30 PASS
802.11ac (VHT80)
Channel Freq.
(MHz)
PSD
(dBm/500kHz)
Limit
(dBm/500kHz)
PASS
/FAIL
155 5775 -4.20 30 PASS
Report No.: RF160202D06-1 Page No. 58 / 65 Report Format Version:6.1.1
SPECTRUM PLOT OF WORST VALUE 802.11a 802.11n (HT20)
802.11n (HT40) 802.11ac (VHT80)
Report No.: RF160202D06-1 Page No. 59 / 65 Report Format Version:6.1.1
4.5 Frequency Stability Measurement
4.5.1 Limits of Frequency Stability Measurement
The frequency of the carrier signal shall be maintained within band of operation
4.5.2 Test Setup
4.5.3 Test Instruments
Refer to section 4.1.2 to get information of above instrument.
4.5.4 Test Procedure a. The EUT was placed inside the environmental test chamber and powered by nominal DC voltage. b. Turn the EUT on and couple its output to a spectrum analyzer. c. Turn the EUT off and set the chamber to the highest temperature specified. d. Allow sufficient time (approximately 30 min) for the temperature of the chamber to stabilize, turn the EUT on
and measure the operating frequency after 2, 5, and 10 minutes. e. Repeat step 2 and 3 with the temperature chamber set to the lowest temperature. f. The test chamber was allowed to stabilize at +20 degree C for a minimum of 30 minutes. The supply voltage
was then adjusted on the EUT from 85% to 115% and the frequency record. .
4.5.5 Deviation from Test Standard
No deviation.
4.5.6 EUT Operating Condition
Set the EUT transmit at un-modulation mode to test frequency stability.
Spectrum Analyzer
DC Power Supply
Temperature
Chamber
Report No.: RF160202D06-1 Page No. 60 / 65 Report Format Version:6.1.1
4.5.7 Test Results
FREQUEMCY STABILITY VERSUS TEMP.
OPERATING FREQUENCY: 5180MHz
TEMP.
(℃)
POWER
SUPPLY
(Vdc)
0 MINUTE 2 MINUTE 5 MINUTE 10 MINUTE
Measured
Frequency
(MHz)
Frequency
Drift
(ppm)
Measured
Frequency
(MHz)
Frequency
Drift
(ppm)
Measured
Frequency
(MHz)
Frequency
Drift
(ppm)
Measured
Frequency
(MHz)
Frequency
Drift
(ppm)
50 5.0 5180.043511 8.3997490 5180.043069 8.3144788 5180.043088 8.3180962 5180.043337 8.3661759
40 5.0 5180.043144 8.3289854 5180.042905 8.2828185 5180.042990 8.2992177 5180.04242 8.1892800
30 5.0 5180.042532 8.2107858 5180.042493 8.2032819 5180.042571 8.2182520 5180.042961 8.2936988
20 5.0 5180.043165 8.3330067 5180.043096 8.3196911 5180.042757 8.2541921 5180.04328 8.3552687
10 5.0 5180.04303 8.3069479 5180.042685 8.2403475 5180.042969 8.2951715 5180.043171 8.3341205
0 5.0 5180.042679 8.2392727 5180.042887 8.2793436 5180.042689 8.2411336 5180.042787 8.2601129
-10 5.0 5180.042912 8.2841058 5180.043212 8.3420849 5180.043258 8.3508837 5180.042893 8.2804394
-20 5.0 5180.043212 8.3420478 5180.043293 8.3578134 5180.043424 8.3830503 5180.043437 8.3855214
FREQUEMCY STABILITY VERSUS VOLTAGE
OPERATING FREQUENCY: 5180MHz
TEMP.
(℃)
POWER
SUPPLY
(Vdc)
0 MINUTE 2 MINUTE 5 MINUTE 10 MINUTE
Measured
Frequency
(MHz)
Frequency
Drift
(ppm)
Measured
Frequency
(MHz)
Frequency
Drift
(ppm)
Measured
Frequency
(MHz)
Frequency
Drift
(ppm)
Measured
Frequency
(MHz)
Frequency
Drift
(ppm)
20
5.75 5180.042615 8.2269007 5180.042403 8.1859073 5180.042691 8.2415907 5180.042198 8.1462597
5.0 5180.043165 8.3330067 5180.043096 8.3196911 5180.042757 8.2541921 5180.04328 8.3552687
4.25 5180.042638 8.2313657 5180.042974 8.2961390 5180.042747 8.2523302 5180.042989 8.2990626
Report No.: RF160202D06-1 Page No. 61 / 65 Report Format Version:6.1.1
4.6 6dB Bandwidth Measurment
4.6.1 Limits of 6dB Bandwidth Measurement
The minimum of 6dB Bandwidth Measurement is 0.5MHz.
4.6.2 Test Setup
4.6.3 Test Instruments Refer to section 4.1.2 to get information of above instrument.
4.6.4 Test Procedure MEASUREMENT PROCEDURE REF
a. Set resolution bandwidth (RBW) = 100kHz
b. Set the video bandwidth (VBW) ≥ 3 x RBW, Detector = Peak.
c. Trace mode = max hold.
d. Sweep = auto couple.
e. Measure the maximum width of the emission that is constrained by the frequencies associated with the two amplitude points (upper and lower) that are attenuated by 6 dB relative to the maximum level measured in the fundamental emission
4.6.5 Deviation from Test Standard No deviation.
4.6.6 EUT Operating Condition
The software provided by client to enable the EUT under transmission condition continuously at lowest, middle and highest channel frequencies individually.
EUT SPECTRUM ANALYZER 10dB ATTENUATION
PAD
Report No.: RF160202D06-1 Page No. 62 / 65 Report Format Version:6.1.1
4.6.7 Test Results
802.11a
CHANNEL FREQUENCY
(MHz)
6dB BANDWIDTH
(MHZ)
MINIMUM LIMIT (MHZ)
PASS / FAIL
149 5745 16.58 0.5 PASS
157 5785 16.60 0.5 PASS
165 5825 16.60 0.5 PASS
802.11n (HT20)
CHANNEL FREQUENCY
(MHz)
6dB
BANDWIDTH (MHZ)
MINIMUM LIMIT (MHZ)
PASS / FAIL
149 5745 17.76 0.5 PASS
157 5785 17.75 0.5 PASS
165 5825 17.72 0.5 PASS
802.11n (HT40)
CHANNEL FREQUENCY
(MHz)
6dB BANDWIDTH
(MHZ)
MINIMUM LIMIT (MHZ)
PASS / FAIL
151 5755 36.58 0.5 PASS
159 5795 36.59 0.5 PASS
802.11ac (VHT80)
CHANNEL FREQUENCY
(MHz)
6dB
BANDWIDTH (MHZ)
MINIMUM LIMIT (MHZ)
PASS / FAIL
155 5775 75.28 0.5 PASS
Report No.: RF160202D06-1 Page No. 63 / 65 Report Format Version:6.1.1
SPECTRUM PLOT OF WORST VALUE
802.11a 802.11n (HT20)
802.11n (HT40) 802.11ac (VHT80)
Report No.: RF160202D06-1 Page No. 64 / 65 Report Format Version:6.1.1
5 Pictures of Test Arrangements
Please refer to the attached file (Test Setup Photo).
Report No.: RF160202D06-1 Page No. 65 / 65 Report Format Version:6.1.1
Appendix – Information on the Testing Laboratories
We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved according to ISO/IEC 17025. If you have any comments, please feel free to contact us at the following:
Linko EMC/RF Lab
Tel: 886-2-26052180
Fax: 886-2-26051924
Hsin Chu EMC/RF Lab/Telecom Lab
Tel: 886-3-6668565
Fax: 886-3-6668323
Hwa Ya EMC/RF/Safety
Tel: 886-3-3183232
Fax: 886-3-3270892
Email: [email protected]
Web Site: www.bureauveritas-adt.com
The address and road map of all our labs can be found in our web site also. --- END ---