A standard in-line pump offering advanced design features for process and general pumping.
New CENTRIFUGAL PUMPS 2014-4 Page 1 September 1973
FEATURES D-1100
Worthington D-1100 vertical in-line pumps
Sizes 1 to 60 hp, 800 gpm, 600 ft. 20E-20253
WORTH I NGTON
Standard Pump Marketing Dept., East Orange, N. J. WORTHINGTON
2014-4 Page 2
September 1973 CENTRIFUGAL PUMPS New
D-1100 FEATURES
Features and Options of In-Line design offer efficiency and economy
Worthington, a name synonymous with excellence in modern pump design and engineering, offers the D-1100 vertical in-line pumps. The application advan-tages of the D-1100 vertical in-line pump will provide the solution to many of the problems facing industry today. Built to rigid specifications, all pumps are fitted with stainless steel internal parts; closed, scalloped impeller; wear-resistant shaft sleeve; and money-saving, optional inducer. These construction high-lights combined with rugged standardized JMV ex-tension and JPV extension motors produce an efficient and economical package that's hard to beat.
20E-20254
In-line mounting offers many money-saving features and advantages.
• Simplified plant layout because of reduced space requirements and in-line mounting
• Easy, economical installation — No concrete foun-dation or grouting needed
• Rotating assembly and motor can be removed with-out disturbing the piping
• Eliminates alignment costs and problems
• Pump inspection and maintenance can be accom-plished at pump site saving time and money
In addition to these advantages, the optional inducer is also offered on the D-1100 vertical in-line pumps. The inducer lowers required NPSH of a given pump over the normal operating range. This affords the op-portunities of lower inlet pressures, better tank ar-rangements, and higher suction lifts. It will allow selection of pumps at higher speeds thereby enabling selection of a less costly pump. Should NPSH prob-lems occur after startup the inducer may be added without disturbing the pump piping system or basic pump configuration.
20E-202515
WORTHINGTON Litho'd II.S..1.
New CENTRIFUGAL PUMPS 2014-4 Page 3 September 1973
FEATURES D-1100
Stainless Steel fitted for reliable performance
The Worthington D-1100 vertical in-line pumps offer flexibility and durability in construction design and materials, depending on the specific application re-quirements. Pumps are available in ductile iron, 316 stainless steel or Worthite 20 construction.
All D-1100 vertical in-line pumps have stainless steel internal parts to provide maximum performance under severe operating conditions. The shaft sleeve, the im-peller and the impeller mounting screw and washer are all made of stainless steel to prevent corrosion and extend wear life.
The standard shaft sleeve construction eliminates the necessity of replacing the entire motor shaft, should the surface under the seal or packing begin to wear. The closed, scalloped impeller, the optimum selec-tion for most pump applications, retains its high effi-ciency longer than open impeller designs. It also provides:
• Inherent axial hydraulic balance resulting in longer seal and bearing life.
• Low NPSH requirements
• No clearance adustment necessary
20,20290
The impeller is held securely in place by a positive lock washer and impeller screw, and is keyed to the shaft for best possible transmission of torque.
All these stainless steel "standards" mean greater savings and service to the customer, through supe-rior hydraulics, interchangeability, and unexcelled modularity.
20E-20266
Standard Pump Marketing Dept., East Orange, N. J. WORTHINGTON /
CENTRIFUGAL PUMPS New
FEATURES D-1100
Choice of Motor Design for application flexibility standardized for economy and availability
2014-4 Page 4 September 1973
To assure maximum flexibility, availability and econ-omy, Worthington's D-1100 vertical in-line pumps are being offered with two motor design standards.
The NEMA "C" face standard motor, designed for use on vertical in-line pumps, offers the best availability and economy. This motor has single row ball bearings which are of adequate size to handle normal pump loads.
The alternate motor design is the ANSI* standard "C" face motor, specifically designed for vertical in-line pumps. This motor includes double row ball bearings to minimize shaft deflection and end play, an extra large diameter shaft, and TEFC construction. Depend-ing on the application, explosion proof motors are available.
Both of these motors are equipped with drip cover and lifting eye bolts or lugs.
The D-1130 pump utilizes a NEMA JM shaft extension motor. This shaft extension is for use with a mechani-cal seal.
The D-1131 and D-1132 pump models utilize the NEMA JP shaft extension motor and can be furnished with either the NEMA standard motor or the ANSI vertical in-line standard motor design. This shaft extension is for use with convertible box (D-1131) or mechanical seal cover (D-1132). Standard motors mean greater availability and economy; both on its initial application and in any subsequent field requirements which might arise. These motors are produced by most major mo-tor manufacturers and in many cases are readily avail-able as a stock item.
'Proposed ANSI B -73.2 standard for vertical in - line pumps
20E-20257
WORTHINGTON L,ihnd tn 11.S..1.
2014-4 Page 5 September 1973
New CENTRIFUGAL PUMPS
FEATURES
D-1100
Model D-1130 with JM shaft extension
Standard Pump Marketing Dept., East Orange, N. J. WORTHINGTON
2014-4 Page 6
CENTRIFUGAL PUMPS
New September 1973
D-1100
FEATURES
Models D-1131 and D-1132 with JP shaft extension
WORTHINGTON Litho'd (1.S.A
Two piece packing 4 a
Stuffing box covet'. Alto , seating flexibility •.(fhstptng or mechanic-5
, Stuftmo boy, i5cRet con (in and out pra -v:derfl.
shAfing hox conli 'riandertic,r l p i.
8-9 2
sf
9-2
New CENTRIFUGAL PUMPS
2014-4 Page 7 September 1973
FEATURES
D-1100
D-1100 Provides extensive coverage to meet your exact needs
This thoroughly engineered modular pump line provides superior hydraulics and better cover-age across the board, as the "flag chart" below shows. You'll find more and better selections at any design point. And that means whatever your application — even if it falls at the top or bottom of the chart where efficiency is traditon-
ally hard to come by — you can select a pump to reduce operating costs.
Each pump in the line (ranging up to 60 hp, ca-pacities up to 800 gpm, heads up to 600 ft.) is designed for optimum performance with great-est reliability and lowest cost.
-4 4 1.- 0-0--
ii 7,- .,„
■
mffilems.mileamEnis 1111WW
7 --- I
e,x tz , NIN■iming
I 4474171r*. . ., /,...4
t' ., 'Y
---v44-01—x,N
-A-
36-0, CI Pr
.-
k )(2 -t.
.-
4,. -
-,_ .... .-:,.
1 1 4,
, i7011 )k-,1;zm'Ar _ ,e....—.. * ._
V, -V *
,0,: --,'
I
25
200
50
CAPACITY
.50C. i:J0
100 150 250
2000 US 1,Fio
500 10/15,
rcr,
r7C
_
IIMMIEEEMILIIIIIIEL*C§6r.—
111111.11111BatrAINIMILIMIC.
■11111111111EIMMiktaNlek, ■MiliMMEIMMENIV)
- PLIIINNIIMIllik minfalrfallellp
■1-111liallEr
Fr 3`-
,,,,t,
" '
\
a.,
- ,:o,, ..,T, -..-
-
-re ,-, —
5uu tut, 11.5,U U5 ufriol
25
50
100 i6o 260 1113'14R CAPACITY
Standard Pump Marketing Dept., East Orange, N. J. WORTHINGTON
CENTRIFUGAL PUMPS New
D-1100 FEATURES
Dimensions
Pump Dimensions — D-1130/1131/1132
Pump Size
Suction Size
Discharge Size X Y SD T DP
D-1130 DP
D-1131/1132
2 x 11/2 x 6 2 11/2 7% 77/8 15 7 5% 81/4
3 x 11/2 x 6 3 11/2 61/2 81/2 15 8 51/2 81/4
3 x 2 x 6 3 2 8 9 17 8 5~ 81/2
2 x 11/2 x8 2 11/2 83/4 81/4 17 7 6,/i4 836
3 x 11/2 x 8 3 11/2 8~ 10 1/4 19 8 67/16 8716
3x 2 x 8 3 2 10 10 20 8 61/2 81/2
4 x 3 x 8 4 3 10~ 111/4 22 9 6~ 8%
3 x 11/2 x 10 3 11/2 8% 10 1/8 19 8 61/83 81/2
3 x 2x 10 3 2 9% 10% 20 8 6% 83/4
4 x 3 x 10 4 3 121/2 121/2 25 9 69/14 8' V16
6 x 4x 10 6 4 131/2 141/2 28 10 7% 9%
3 x 11/2 x 13 3 11/2 11 1/e 12% 24 8 — 9 1/s
3 x 2 x 13 3 2 113/4 121/4 24 8 — 9,1A4
4 x 3 x 13 4 3 14 14 28 9 — 9%
Motor Dimensions* — D-1130/1131/1132
Frame Size JMV or JPV
JMV JPV AG 0 AG o
182 11% Vio 12% 96
184 127s 9'/I6 137s 9Y16
213 13% 10716 151/2 111/4
215 15% 10M4 17 111/4
254 173/14 12%4 19% 131/2
256 19'/16 10/14 21 7/14 131/2
284 19 ,/16 14 221/4 14%
286 20'/I6 14 233/4 14%
324 203/4 16 24% 163/4
326 22 1/4 16 257/s 1644
*Both standard and ANSI type.
2014-4 Page 8 September 1973
WORTHINGTON Lilho'd 0n U.S.A.
Stuffing Box Data — D-1131
Depth O.D. Gland 0-1131 Bore of of Packing No. Stud
Box Sleeve Size Rings Dia.
143-184JPV 2 2.32 1% 5/i6 x VI6 5 %
213-326JPV 21/2 2.83 1 3/4 % x Vs 5 1/2
New CENTRIFUGAL PUMPS
2014-4 Page 9
September 1973
FEATURES D-1100
Technical Data
Materials of Construction
Part Ductile Iron 316 SS Worthite 20
Casing Casing Wear Ring Casing Gasket Casing Cap Screws Impeller Impeller Screw Impeller Screw Washer Shaft Sleeve Adapter Adapter/St. Box Ring Mechanics! Seal/St. Box Cover Motor Shaft
Ductile Iron 316 SS Durabla Steel 316 SS 316 SS 316 SS 416 SS Cast Iron (1) 316 SS (2) Ductile Iron (1) Steel
316 SS None Durabla 316 SS 316 SS 316 SS 316 SS 316 SS Cast Iron 316 SS 316 SS Steel
Worthite 20
None Durabla 316 SS Worthite 20 Worthite 20 Worthite 20 Worthite 20 Cast Iron Worthite 20 Worthite 20 Steel
0-1131 Packing Gland
Studs & Nuts
Lead Asbestos Steel Split Gland
316 SS
Blue Asbestos 316 SS Split Gland
316 SS
Blue Asbestos Worthite 20 Quench Gland
Worthite 20
0-1130, 0-1132 Mechanical Seal Type 21 BP-171 Type 9 QP-1C1 Type 9 QP-1C1
Optional Construction Casing Support Inducer Shaft Sleeve Casing Gasket Packing Quench Gland
Steel 316 SS 17% Chr. or 316 SS Teflon
, Worthite 20
Steel 316 SS
— Teflon Worthite 20
Steel Worthite 20
— Teflon
—
(1) Adapter and mechanical seal cover on 0-1130 pumps are integral and are cast iron. (2) Adapter ring on 0-1130 pumps is cast iron.
Shaft and Shaft Sleeve Dimensions D-1130, D-1131, and D-1132
Pump Model
Motor Frame
SHAFT DIAMETER 0.0.
of Sleeve
At Impeller
Under Sleeve
- 01130 143-215 JMV 254-326 JMV
7/8 11/4
1 1 3/8
1% 1%
0-1131 and
0-1132
143-184 JPV 213-326 JPV
1/2 11/4
1 1~
1% 1 3/4
Standard Pump Marketing Dept., East Orange, N. J. WORTHINGTON
CENTRIFUGAL PUMPS New
FEATURES D-1100
Nationwide distribution assures availability and economy of pumps, parts and service
2014-4 Page 10 September 1973
An extensive network of franchised Worthington pump distributors, located in every major trading area in the country, is your assurance that there is, in fact, a Worthington representative near you for prompt, local service.
Our distributors representatives are trained special-ists in pumping equipment. They can offer expert as-sistance on pump application, selection, installation, operation, and maintenance.
And Worthington distributors carry inventories of pumps and parts for immediate reaction to your needs.
They are also backed up by Worthington's Distribution Centers. If the distributor doesn't have a less fre-quently used model or size in stock, he can get it from a Distribution Center quickly.
Your Worthington distributor is factory trained. He can give you pump know-how promptly and conveniently.
You can locate the Worthington distributor in your area by consulting the Yellow Pages of your local tele-phone directory.
20E-20163
Worthington Standard Pump Corp. 14 Fourth Avenue East Orange, New Jersey 07017
2014-B1
A subsidiary of Worthington Pump International, Inc.
WORTHINGTON
WORTHINGTON Lithdd
