Arman Tejarat Behta www.AtbCo.com Material Composition: Made from Aramid fiber, Mineral fiber & Inorganic bounded with Synthetic NBR Elastomers. Applications: Suitable for high performance, Oil resistance gasket material with excellent thermal, chemical & mechanical properties. Standard Sheet Size 1500×2000 mm,1500×4000 mm,1500×1500 mm, 1500×4500 mm,1500×3000 mm, 2000×3000 mm Material data General Information Max. Peak Temperature 250°C Max. Continuous Temp 180°C Max. Continuous Temp. with Steam 120°C ASTM F104 Line call-out Internal Pressure limit 50 bar F12122A9B5E12M4 Color Green/White/Red/Yellow Thickness (mm) 0.25 - 5 Physical properties Standard Unit Value Density (Nominal) DIN 28 090 [g/cm³] 1.15 - 1.90 Tensile Strength (a) Across Grain ASTM F152 [N/mm²] (b) Across Grain DIN52910 [N/mm²] Compressibility ASTM F 36A [%] 7 - 15 Recovery ASTM F 36A [%] Fluid absorption In ASTM oil no.3 ASTM F 146 Increase in mass [%] 15 Increase in thickness [%] In fuel B ASTM F 146 Increase in mass [%] Increase in Thickness [%] In water/antifreeze ASTM F 146 Increase in mass [%] 15 Increase in Thickness [%] Ignition loss DIN 52911 [%] 40 STRESS RESISTANCE (16h 175°C) DIN 52913 [N/mm²] 10 Tolerance Thickness 1 mm = ± 0.10 mm Length ± 50 mm >1mm = ± 0.10% width ± 50 mm An ISO 9001:2000/TS 1694:2002 certified company NOTE: ALL INFORMATION AND RECOMMENDATIONS GIVEN IN THIS BROCHURE ARE CORRECT TO THE BEST OF OUR KNOWLEDGE. SINCE CONDITIONS OF USE ARE BEYOND OUR CONTROL THE INFORMATION PROVIDED AND ONLY SERVE AS A GUIDELINE. USERS MUST SATISFY THOSE SELVES THAT PRODUCTS ARE SUITABLE FOR THE INTENDED PROCESS AND USES. WE RESERVE THE RIGHT TO CHANGE PRODUCT DESIGN AND PROPERTIES WITHOUT NOTICE.
Transcript
Arman Tejarat Behta www.AtbCo.com
Material Composition: Made from Aramid fiber, Mineral fiber & Inorganic
bounded with Synthetic NBR Elastomers.
Applications: Suitable for high performance, Oil resistance gasket
material with excellent thermal, chemical &
mechanical properties.
Standard Sheet Size 1500×2000 mm,1500×4000 mm,1500×1500 mm,
1500×4500 mm,1500×3000 mm, 2000×3000 mm
Material data General Information
Max. Peak Temperature 250°C
Max. Continuous Temp 180°C
Max. Continuous Temp. with Steam
120°C ASTM F104 Line call-out
Internal Pressure limit 50 bar F12122A9B5E12M4
Color Green/White/Red/Yellow
Thickness (mm) 0.25 - 5
Physical properties Standard Unit Value
Density (Nominal) DIN 28 090 [g/cm³] 1.15 - 1.90
Tensile Strength
(a) Across Grain ASTM F152 [N/mm²]
(b) Across Grain DIN52910 [N/mm²]
Compressibility ASTM F 36A [%] 7 - 15
Recovery ASTM F 36A [%]
Fluid absorption
In ASTM oil no.3 ASTM F 146
Increase in mass [%] 15
Increase in thickness
[%]
In fuel B ASTM F 146
Increase in mass [%]
Increase in Thickness
[%]
In water/antifreeze ASTM F 146
Increase in mass [%] 15
Increase in Thickness
[%]
Ignition loss DIN 52911 [%] 40
STRESS RESISTANCE (16h 175°C)
DIN 52913 [N/mm²] 10
Tolerance Thickness 1 mm = ± 0.10 mm Length ± 50 mm >1mm = ± 0.10% width ± 50 mm
An ISO 9001:2000/TS 1694:2002 certified company NOTE:
ALL INFORMATION AND RECOMMENDATIONS GIVEN IN THIS BROCHURE ARE CORRECT TO THE BEST OF OUR
KNOWLEDGE. SINCE CONDITIONS OF USE ARE BEYOND OUR CONTROL THE INFORMATION PROVIDED AND ONLY SERVE AS
A GUIDELINE. USERS MUST SATISFY THOSE SELVES THAT PRODUCTS ARE SUITABLE FOR THE INTENDED PROCESS AND
USES. WE RESERVE THE RIGHT TO CHANGE PRODUCT DESIGN AND PROPERTIES WITHOUT NOTICE.
