GROUP A

HP 54 (Energy) available to the rotorHP 60 (Power) available to the rotorHP 64 (Energy) max to hydraulic motorHP 79 (Power) max to hydraulic motor

ENERGY

HYDRAULIC REACH MOWERS

Stiff pipes

Electric Roll-over protection system SAB (option)

Power slew 95°

Parallel arm geometry

Frame variablesection

Pressurizedoil tank

Automatic hydraulicblock for transport

Oil cooler inAlluminumwith thermostat

Flail head 1,25 m

Electronic proportional controls

HP Tractor 100 110 120Min. tractor weight ** Min. tractor width **

Kg m

TSH 600G 3600 2,30TSH 650GZ 3600 2,30

(**) for a better tractor stability it is recommend to use the universal axle bracket (cod. ARK 200) and relevant completing kit

Working positions (m)TSH 600G TSH 650GZ

A m 6,05 6,62

B m 4,17 4,73

C m 1,20 1,20

D m 5,51 5,90

E m 7,20 7,62

F m 2,31 2,82

G m 1,7 1,7

H m 6,27 6,85

Floating head system

“Overlap” spiral rotor withtwo spiral rows

1st arm rectangular section (mm 120x180)

Piston hydraulic systemin closed circuit (Power Version)

Hydraulic break-back withaccumulator controlledautoreset facility (SRA)

95°

FERRI srl - Via Govoni, 30 - 44034 Tamara (FE) Italy - Tel. +39 0532 866866 - Fax +39 0532 866851 - info@ferrisrl.it - www.ferrisrl.itSpare parts: Tel: +39 0532 866993 - Fax: +39 0532 867061 - e-mail: parts@ferrisrl.itAfter Sales Service: Tel: +39 0532 866991 - Fax: +39 0532 866851 - e-mail: service@ferrisrl.it

Equipped with:

IT IS RECOMMENDED that the connection between tractor and shredder and its setting up should be made with the Dealer according the instructionsand warnings listed on our Use and Maintenance Manual. For further information please contact our after sales service.

Warning

(*) Reach measured from tractor centre line to head edge.

Technical dataModel Max horizontal

reach*Weight Oil Telescopic

extensionRotor P.t.o. Flail head

anglem Kg l m rpm MAX rpm

TSH 600G Energy 6,05 1.510 170 - 3.000 540 235°TSH 650GZ Energy 6,62 1.670 170 0,60 3.000 540 235°TSH 650GZ Power 6,62 1.670 140 0,60 2.800 540 235°

Machines with Electric Proportional Controls “Advance Tronic”Model

TSH 600G Energy Advance Tronic with flail head TNS 125 m 1,25

TSH 650GZ Energy Advance Tronic with flail head TNS 125 m 1,25

TSH 650GZ Power Advance Tronic with flail head TNSC 125 m 1,25

Completing equipment to the base machineCode Length cm

TK8005/06 (705-920) Stabilizers to the tractor OPT001121000 - “Delta yoke” for stabilizers TSN5033 - Stabilizers for “Delta yoke” TGA5018 (340-460) Top link short TGA5019 (485-720) Top link long ARK200 - Axle Brackets – - Axle Plates Kit (x ARK200)

OptionCode

TSB7032 Lift float (LFA electric) – Electric roll-over protection system

Flail head TNS 125 TNSC 125

Cutting width (m) 1,25 1,25Rotor speed (rpm) 3000 2800Blade tip speed (m/sec) 60 60Flail head angle 235° 235°Weight (kg) 290 315

TNS 125 (Energy)Motor with direct drive

TNSC 125 (Power)Side toothed belt drive

Flails / TNS 125 - TNSC 125Interchangeable on the same rotor

Multiuse blades for: grass, shrubs, bushes, sticks, woodØ 4 cm

“T” Hammer blades for woodØ max 5 cm

Unidirectional bladesØ max 6 cm

Cod. 0901181 Cod. 0901141 Cod. 0901187n° 52 n° 26 n° 26Standard

� Flail head TNS 125 (Energy version) � Flail head TNSC 125 (Power version) �Wire trap � Rear roller Ø 140 mm � Rotor balancing on side flanges � Replaceable skids � Piston hydraulic system in closed circuit (Power version) � Electronic proportional controls “Advance Tronic” � Oil cooler in Alluminum with thermostat � Telescopic extension m 0,60 (TSH 650GZ) � Mechanic Roll-over protection system � Hydraulic break-back with accumulator controlled autoreset facility (SRA) – with electric disengagement (PSS), a maximum relief valve is available for arm protection � Electric reversible rotor (DSR Electric) � Floating head system � Hydraulic Power slew 95° � Bumpers with illumination system � Front and rear abrasion resistant guard for flail head � Oil and Pto shaft