INSTALLATION & SOFTWARE

MANUAL

FEVERSCREEN.COM.AU

Automated Screening

Technology

FEVERSCREEN

FEVERSCREEN

FEVERSCREEN

The space between and immediately around Feverscreen and the individual to be

screened is critical.

Feverscreen, IEC and ISO provide a series of recommendations to help ensure best

possible conditions to achieve more accurate screening results. These include:

• Approach from 2m away remaining parallel to the terminal at all times

• Faces must be parallel to unit when screening

• Eyeglasses and facial covering must not obstruct face during screening

• Ambient temperature must be controlled

• Screening, if possible, to be conducted in a controlled indoor environment

between 18-24°C

• Ensure screening subject is not sweating at time of screening

• Ensure screening subject has not recently washed their face

• The screening unit itself must not be under

o bright lights

o air-conditioning

o drafts

o heat or cold sources

• If a high temperature is detected follow up with a clinical device.

Feverscreen is not a clinical device.

• Ensure backdrop is Non-Reflective.

• Avoid conducting screening in spaces which have dark backgrounds

• Avoid conducting screening in dimly lit environments

Installations musty comply to the above recommendations and be installed as per

diagram 1

What happens in and around this space is critical

2

FEVERSCREEN

37°C

Setup the front of the cue to start 2m away from

Feverscreen Unit

Install unit as required to allow

individuals to lean in and place

face within onscreen outline from screening pt

Create a screening line

parallel to Feverscreen

2.0m

0.5m -0.75m

0.0m

1

Setup Screening point marker

approx 0.5-0.75m from Feverscreen

3

5

4

Setup appropriate social distancing cue markers at 1.5m intervals

2

SCREENING POINT

FEVERSCREEN SCREENING STATION SETUPDIAGRAM 1

Tilt (Bollard version only) to

allow individuals to lean in

appropriately.

6

3

FEVERSCREEN

150mmBase Mounting

Removable

Cap

Capping

plate

Specifications are subject to change. FeverScreen and Fever Screening Terminal products are sold with a limited 1year warranty. All

rights reserved. FeverScreen and Fever Screening Terminal logo’s are trademarks or registered trademarks of FST Inc. All other

trademarks are the property of their respective owner’s.

13

4

2

1. Remove cap from bollard

2. Secure bollard to surface (or optional base plate) and run in cables

3. Secure Feverscreen (Model: FST-021314-AU-B) to cap and attach cabling

4. Attach cap to bollard

5. Replace capping plate and power up

Important Note: Approach and usage must be as per diagram 1. Approach must be

parallel from 2m away.

5

FEVERSCREEN BOLLARD SETUP DIAGRAM 2

Compatible Model: FST-021314-AU-B

4

FEVERSCREEN

Specifications are subject to change. FeverScreen and Fever Screening Terminal products are sold with a limited 1year warranty. All

rights reserved. FeverScreen and Fever Screening Terminal logo’s are trademarks or registered trademarks of FST Inc. All other

trademarks are the property of their respective owner’s.

1

2

4

1. Attach supplied wall mount securely to wall

2. Attach cabling to Feverscreen unit FST-021314-AU-W

3. Slide Feverscreen unit into wall mount

4. Secure Feverscreen unit to wall mount with grub screw

Important Note: Wall mounted version cannot be tilted. Approach and usage must be as

per diagram 1. Approach must be parallel from 2m away.

FEVERSCREEN WALL MOUNT SETUP DIAGRAM 3

Compatible Model: FST-021314-AU-W

3

5

Input / Output

NetworkNetwork is required for setting adjustment. Default address

is 192.168.1.50

Power 12v DC (2.5mm Tip positive)

Relay2 pin terminal (N/O or N/C with time adjustment from 0 to

10 seconds. Adjustable via software)

I/O 4pin (I/O not available in current release)

Technical Data - PortsFEVERSCREEN

Network Power Relay I/O

6

SOFTWARE

MANUAL

FEVERSCREEN.COM.AU

Automated Screening

Technology

FEVERSCREEN

FEVERSCREEN

FEVERSCREEN

2

SOFTWARE

v2.3.1

Automated Temperature Screening

Technology

Item Minimum Hardware Requirements

Processor Intel i3 64-bit (x64) processor or equivalent

Ram 4MB

O/S Win10 (recommended)

HDD (recommended) 64GB or higher recommended for database feature

HDD (Software

requirements)

5MB of available space

Hardware

Software & Settings FEVERSCREEN

3

Visitor Scan Function

IP Address Set the IP address of your unit and press connect. As the first individual scans

their image will appear in the first tile.

Scanning As people scan, their image will appear in the respective tile in addition to the

main tile bottom. The persons reading and STOP, GO or NO MASK result will

also appear depending on selected options.

History Panel The last eight people scanned will appear across the top of the history panel

together with their temperature reading and time they were scanned. Tiles will

recycle as

People Counting People counter indicates how many people have scanned across the day.

STOP: Indicates individual with abnormal

temperature

NO MASK: Indicates individual not wearing

facemask

Software & Settings FEVERSCREEN

Visitor History Function

Date Range Date Range can be set by user to view respective records

Info Panel Provides Record #, Device #, Date, Time, Mask Status and Green or Red level

temp result

Query After selecting date range user must click query to update results

Export to Export to allows user to export excel spreadsheet of database. Default location

or export is Windows Documents

Pages Allows user to navigate across results

4

Software & Settings FEVERSCREEN

Settings Function

IP Address Default IP address is 192.168.1.50

Capture Interval Time required to successfully take temperature readings between scanning

intervals. 3seconds should be used as a minimum.

Picture Quality Picture quality required to perform a scan

Picture Blur Picture blur level required to perform a scan

Living Threshold Higher threshold requires satisfaction of additional AI evaluations to be

considered human.

Score Threshold Represents the cumulative satisfaction of all above variables as a %

Recognizing Time How many times a person is scanned before a reading is provided. Use higher

levels in harsh environments.

Distance Distance persons are scanned from the unit. Longer distances will decrease

accuracy.

Exposure Lighting Exposure Level

Temperature Threshold Temperature set point. Anything above this point will result in a fail result.

Temp Offset Allows for a temperature offset in harsh environments. NOTE: incorrectly using

this feature can result in false readings. Adjusting this feature is the responsibility

of the user.

Relay Switching Time Time relay unit will be active

Closing State Select between Normal (will activate when temperature is normal) or Abnormal

(will activate when temperature is high)

OI Out Mode (Beta) N/A

Temp Detect Mode Select between indoor or outdoor.

5

Software & Settings FEVERSCREEN

Feature Function

Set Sound on Scanning Provides verbal notifications on monitoring PC

Show Temperature for

calibration

Allows user to display temperature during visitor scans

Monitor for Facemask Allows user to monitor for facemasks. When this is ticked field unit will remind

users to wear facemask. In addition if an individual presents without a facemask

an amber alert will appear in Visitor Scan with the label ‘No Mask”. If Mask email

alerts are to be used this setting must be ticked.

Save Changes Save changes must be clicked after each modification

6

Important information: Ports 80 and 8085 must be open for software to communicate

Software & Settings FEVERSCREEN

7

Time Function

Time Sync When connected click Sync Now to synchronize time to local PC

Software & Settings FEVERSCREEN

8

Advanced Function

Temperature When connected click Reset to calibrate temperature manually

Reboot Click Reboot to remotely reboot device

Application data path Allows user to set path for database C:\Feverscreen is default

Software & Settings FEVERSCREEN

9

Network Function

IP Address Default IP address is 192.168.1.50

Subnet Mask Allows setup of subnet mask to client requirements

Default Gateway Allows setup of default gateway to client requirements

Primary DNS Server Allows setup of Primary DNS server to client requirements

Secondary DNS Server Allows setup of Secondary DNS server to client requirements

Software & Settings FEVERSCREEN

10

Light Function

Mode Onboard lighting can be set to AUTO or Manual

Manual Allows user to turn lights on in dimly lit environments to improve scanning quality

Auto Allows user to set an auto on/off time dependant on ambient light levels

Brightness Allows user to set the brightness level of the onboard lighting

Software & Settings FEVERSCREEN

11

Mail Function

SMTP Server Enter SMTP server details

Mail Address Enter From: Mail address

Port Enter required port

Username Enter username

Password Enter password

Send email alert on high

temperature

Sends email including picture when an individual is detected with abnormal

temperature

Send email alert on not

wearing masks

Sends email including picture when an individual is detected not wearing a

facemask

Test Email Sends a test email to confirm mail settings

Save Changes Save changes must be clicked after each modification

FEVERSCREEN

CAUTION

In order for Feverscreen to maintain accuracy, units must be installed in a stable environment which

does not fluctuate in temperature. ISO recommends indoor environments between 18-24° Celsius.

External environments and environments with temperatures outside of this range must be within the

specification of the unit and not be subject to sudden fluctuations in temperature.

Feverscreen cannot be installed in environments effected by the below:

1. In direct sun

2. In any situation where sun is reflecting off surrounding

surfaces (Feverscreen utilizes a highly sensitive thermal

module and can pick up on reflected sun/heat sources

from over 100m away)

3. In instances where a persons face is reflecting sun. Both

the thermal module and facial recognition module require a

clear fully shaded view of the persons face. Where a

person presents with a half shaded view of the face AI

algorithms may be inhibited.

4. In any situation where sun will influence the temperature of

an individual or the unit itself

1. In rain or wet environments

2. Despite the unit being splash proof, any form of water or

humidity over the thermal module will impact on the

accuracy of results

3. Water, dust or grime covering the lens of the facial

recognition camera can impact on AI calculations and

effect temperature readings

1. Under air conditioning

2. In areas effected by frost or mildew

3. In any situation where the temperature of the unit can

fluctuate significantly due to fluctuations in surrounding air

temperature

1. In wind or high flow environments

2. In any situation where the temperature of the unit can

fluctuate significantly due to winds or fans causing airflow

between the unit and individual being screened.