SemIIIINSTAEDec10_page1_image1.pdfSemIIIINSTAEDec10_page2_image1.pdfSemIIIINSTAEDec10_page3_image1.pdf
files.stupidsid.comfiles.stupidsid.com/university_papers/VTU/CS (missing papers)/7... · What is a FP — growth algorithm? For the following transaction data set, explain and construct
Documents
files.stupidsid.comfiles.stupidsid.com/university_papers/engineering/Civil...the rate of 25001itres/sec through a 1.2m diameter pipe. Tests were conducted on a f2cm diarneter pipe
files.stupidsid.comfiles.stupidsid.com/university_papers/engineering/... · ii) Check the gears for dynamic load by using both Barth velocity factor method and Buckingham's method.
files.stupidsid.comfiles.stupidsid.com/university_papers/engineering/Mechanical 2010... · Show both the NPSH characteristics graphicaliÿ and indicate the cavitating and non-cavitating
files.stupidsid.comfiles.stupidsid.com/university_papers/engineering/Civil 2010...What is meant by Conjugate Beam? ... (AFD), Shear Force Diagam (SFD) and Bending Moment Diagram ...
files.stupidsid.comfiles.stupidsid.com/university_papers/engineering/Civil... · · 2015-07-30Caiculate the quantities of following items of work by referring the drawings : (a)
files.stupidsid.comfiles.stupidsid.com/university_papers/engineering/Civil 2010 onwards... · (b) What are the various investigations required for reservoir planning ? 7. .write short
files.stupidsid.comfiles.stupidsid.com/university_papers/engineering/Civil 2010... · Explain Belting method of 10 valuation for land with an example. (b) Work out the quantities
files.stupidsid.comfiles.stupidsid.com/university_papers/engineering...Differentiate between the mechanism of filmwise and dropwise condensation. Classify the Heat Exchangers. Explain
files.stupidsid.comfiles.stupidsid.com/university_papers/engineering... · With neat sketch of CIM wheel, explain the salient features of CIM system Explain following terms (i) Tool
files.stupidsid.comfiles.stupidsid.com/university_papers/engineering/Civil...Assume whirl at outlet to be zero. Differentiate between impulse turbine and reaction turbine. Describe
files.stupidsid.comfiles.stupidsid.com/university_papers/engineering/Civil 2010...Design an isolated pad footing for a column ... Design a combined rectangular footing for two columns
files.stupidsid.comfiles.stupidsid.com/university_papers/engineering/May 2013/SE/EXTC/EDC2.pdf · (a) Explain Miller's Theorem. (b) For a cascaded amplifier, show that overall lower
6Gf 6GF - files.stupidsid.comfiles.stupidsid.com/university_papers/engineering/... · [Total Marks: 100 N.B.: (1) Questibn No.1 is compulsory. (2) Attempt any four out of remaining
files.stupidsid.comfiles.stupidsid.com/university_papers/engineering/Mechanical 2010... · f) State the assumptions made in the Lewis equation used for design of a gear and explain
files.stupidsid.comfiles.stupidsid.com/university_papers/engineering/Civil 2010 onwards/sem6/GE2_D13.pdfCalculate critical depth in excavation in clay deþosits- Properties are UCS
files.stupidsid.comfiles.stupidsid.com/university_papers/engineering/Civil... · · 2015-07-30Find the quantities of earth work from the following details Width of road formaticn
files.stupidsid.comfiles.stupidsid.com/university_papers/engineering... · (b) Distinguish between filmwise and Dropwise condensation. (c) Derive an expression of buoyant force per
