• Reliable operating mechanism
• Simple construction and easy maintenance
• Ideal solution for agricultural filtration requirements
• Automatic flushing according to pressure differential
• No interruption of downstream flow during flushing
• High reliability and durability
• Hydraulic or electronic control
Hydraulic self-cleaning screen filters, with no external power source requiredFiltomat M100/MG Filters
features:
flow rates minimum operating pressure
water for cleaning filtration degrees
M100: up to 400 m3/h(1,760 gpm)
MG: up to 800 m3/h (3,520 gpm)
2 bar (30 psi) less than 1% of the total flow 500-80 micron
How the Filtomat Filters Work
General
The Amiad Filtomat M100 and MG Series are automatic, self-cleaning filters, ideal for remote installation sites, with
a water-driven self-cleaning mechanism that doesn’t require an external power source for operation. With a variety of
screen areas the M100 and MG models support flow rates of up to 3,520 gpm (800 m3/h), with filtration degrees of 500
down to 80 micron and inlet/outlet diameters from 2” to 14”.
The Filtration Process
The filtration process begins when raw water flows through the filter inlet into the coarse screen which pre-filters the
water to protect the cleaning mechanism from large debris. The water then passes through the inner surface of the
fine screen where dirt particles are trapped and accumulate inside the filter, while clean water flows through the filter
outlet. The gradual buildup of dirt on the inner screen surface causes a filter cake to develop which causes an increase
in the pressure differential across the screen.
The Self-Cleaning Process
When the pressure differential across the screen reaches a pre-set level of 0.5 bar (7 psi), the M100 or MG filter starts
the self-cleaning process by opening the internal flush valve. This results in the release of a back-flush stream flowing
through the nozzles out of the hollow suction-scanner shaft to the turbine and to the drainage pipe.
Inlet
Outlet
Coarse Screen
Suction-scannerShaft
Fine Screen
Turbine
Drainage Pipe
Suction Nozzles
Scan to watch the Filtomat M100 Operation Video
M100 Models
Available as a stand alone or as filter bank assembly, with a single control system (AC/DC).
Amiad’s Filtomat M100 Series consists of the following models:
M102C/M103C for up to 40 m³/h (176 gpm)
M103CL/M104C for up to 80 m³/h (350 gpm)
M104CL for up to 100 m3/h (440 gpm)
M104LPN/M106LP for up to 180 m³/h (793 gpm)
M104XLP/M106XLP/M108LP/M110P for up to 400 m³/h (1,760 gpm)
MG Models
Modular configuration, available as a stand alone or as filter bank assembly, with a single control system (AC/DC).
The MG modules are delivered fully assembled, requiring a single connection to the inlet, outlet and drain.
Amiad’s Filtomat MG Series consists of the following models:
MG110 (2 x 108LP) for up to 400 m3/h (1,760 gpm)
MG112 (3 x 108LP) for up to 600 m3/h (2,640 gpm)
MG114 (4 x 108LP) for up to 800 m3/h (3,520 gpm)
Inlet
Outlet
Suction Nozzles
Turbine
Suction-scanner Shaft
Drainage Pipe
Screen
M104CL
M102C/M103C
M103CL /M104C
M100 Models:
14.0
2.0
PSI
4.0
3.0
5.0
7.0
0.5
0.7
0.3
0.2
0.4
1.4
6 10 20 40 60 200 100
0.2
0.04
0.060.08
0.02
0.1
2 4
BAR
0.80.6
1.0
0.4
20 10 6 50
4000 1000 400 2000
200 100 500 1000
GPMM³/H 1
M103CL
M104C
14.0
2.0
PSI
4.0
3.0
5.0
7.0
0.5
0.7
0.3
0.2
0.4
1.4
6 10 20 40 60 200 100
0.2
0.04
0.060.08
0.02
0.1
2 4
BAR
0.80.6
1.0
0.4
20 10 6 50
4000 1000 400 2000
200 100 500 1000
GPMM³/H 1
M102C
M103C
Ø 330 (13")
531
(21”
) *68
4 (2
7”)
710
(28”
) *96
5 (3
8”)
Ø 330 (13")
Head Loss Graphs (in clean water)Typical Dimensional Drawing
315
(12.
4")
811
(32"
) *1
090
(43"
) 346
235
192.5
327
432
508
1 1/2" BSP/NPT
OUTLET
INLE
T
FLUSHING
* Approx. height required for maintenance
REV. DATE DESCRIPTION ECO NO. NAME
F
M100-2250 4" (M104CL) DC Control
SHEET 1 OF 1
SUBJECT/PROJECT:
PART NAME/TITLE:
M100-2250 FILTER CAT. NO.:MATERIAL:
DRAWN
APPROVED
NAME DATE
Confidential property information. DRW. NO.: REV.:
SCALE: 1:8
Amiad Water Systems Ltd.reserves the rights to make changes.
All copy rights reserved to Amiad Water Systems Ltd. SIZE: A4
E
D
File Name:M104C New for 2250 SQ_CM DC Control
3 2 14
AVarious
Elad.k
13 24
D
B
E
C
A
F
UNLESS OTHERWISE SPECIFIED:DIMENSIONS ARE IN MILLIMETERS
WEIGHT: 49 KG
01/06/2016
0KHG3.H040F.001-GA
432 (17”)
Ø 330 (13")
14.0
2.0
PSI
4.0
3.0
5.0
7.0
0.5
0.7
0.3
0.2
0.4
1.4
6 10 20 40 60 200 100
0.2
0.04
0.060.08
0.02
0.1
2 4
BAR
0.80.6
1.0
0.4
20 10 6 50
4000 1000 400 2000
200 100 500 1000
GPMM³/H 1
M104CL
*Approx. length required for maintenanceDim: mm (inch)
M104LPN/M106LP
M104XLP/M106XLP/M108LP/M110P
M100 Models:
50
200 20 10 6 60 40 100
4
0.23.0
0.1
0.02
0.080.06
0.04
1.4
0.4
0.2
0.3
0.7
0.5
2.0
2
0.4
1.0
0.60.8
BAR
7.0
5.04.0
PSI14.0
6 10 20
400 2000 1000
500 100 200 1000 1
GPMM³/H
M104LPN
M106LP
50
200 20 GPM 10 6 60 40 100
4
0.23.0
0.1
0.02
0.080.06
0.04
M³/H
1.4
0.4
0.2
0.3
0.7
0.5
2.0
2
0.4
1.0
0.60.8
BAR
7.0
5.04.0
PSI14.0
6 10 20
400 2000 1000
500 100 200 1000 1
M104XLP
M106XLP
M108LP
M110P
(35.4") (18.4”)
2088 *150
22.3(8.8”)
*1025
INLET OUTLET
DRAIN900 467
(40.4”) (5.9”)(82.2”)
2683
383(35.43”) (38.15”) (15.08”)
900 969
INLET OUTLET
DRAIN
(105.63”) 1575
(42.3”) 160
(6.3”)
Head Loss Graphs (in clean water)Typical Dimensional Drawing
*Approx. length required for maintenanceDim: mm (inch)
MG114
MG110
MG112
MG Models:
2685(105.7”)
(15.08”)383
(43.3”)1100
(30.26”)769
INLET OUTLET
DRAIN
1575(42.3”)
160(6.3”)
2685(105.7”)
(15.08”)383
(43.3”)1100
(30.26”)769
INLET OUTLET
DRAIN
1575(42.3”)
160(6.3”)
2685(105.7”)
(15.08”)383
(43.3”)1100
(30.26”)769
INLET OUTLET
DRAIN
1575(42.3”)
160(6.3”)
Head Loss Graphs (in clean water)Typical Dimensional Drawing
*Approx. length required for maintenanceDim: mm (inch)
0.23.0
0.1
0.02
0.080.06
0.04
1.4
0.4
0.2
0.3
0.7
0.5
2.0
0.4
1.0
0.60.8
BAR
7.0
5.04.0
PSI14.0
GPMM³/H 500
2000 200 100 60 600 400 1000
4020 60 100 200
4000 20000 10000
5000 1000 2000 10000 1
40000
10” MG110
0.23.0
0.1
0.02
0.080.06
0.04
1.4
0.4
0.2
0.3
0.7
0.5
2.0
0.4
1.0
0.60.8
BAR
7.0
5.04.0
PSI14.0
GPMM³/H 500
2000 200 100 60 600 400 1000
4020 60 100 200
4000 20000 10000
5000 1000 2000 10000 1
40000
12” MG112
0.23.0
0.1
0.02
0.080.06
0.04
1.4
0.4
0.2
0.3
0.7
0.5
2.0
0.4
1.0
0.60.8
BAR
7.0
5.04.0
PSI14.0
GPMM³/H
2000 200 100 60 600 400 1000 4000 20000 10000 40000
500 4020 60 100 200 5000 1000 2000 10000 1
14” MG114
Filter Model M102CM103C
M103CLM104C M104CL M104LPN
M106LP
M104XLPM106XLPM108LPM110P
General Data
Maximum flow rate*40 m³/h
(175 gpm)80 m³/h
(350 gpm)100 m³/h (440 gpm)
180 m³/h (793 gpm)
400 m³/h(1,760 gpm)
Inlet/Outlet diameter2” (50 mm)3” (80 mm)
3” (80 mm)4” (100 mm)
4” 100 (mm)4” 100 (mm)6” 150 (mm)
4” (100 mm)6” (150 mm)8” (200 mm)10” (250 mm)
Standard filtration degrees
500, 300, 200, 130, 100, 80 micron
Minimum working pressure
2 bar (30 psi)For lower pressure please consult Amiad
Maximum working pressure
8 bar (116 psi) 10 bar (150 psi)
Maximum working temperature
55°C (131°F)
Weight [empty]2” 22 kg (48.5 lb)3” 25 kg (55 lb)
3” 30 kg (66 lb)4” 35 kg (77 lb)
4” 50 kg (110 lb)4” 90 kg (198 lb)6” 115 kg (253.5 lb)
4” 110 kg (242.5 lb)6” 120 kg (264.5 lb)8” 140 kg (308.6 lb)10” 158 kg (348 lb)
* Consult Amiad for optimum flow depending on filtration degree and water quality.
Flushing Data
Minimum flowfor flushing (at 2 bar - 30 psi)
15 m³/h(66 gpm)
20 m³/h(88 gpm)
22 m³/h(97 gpm)
26 m³/h(114 gpm)
30 m³/h(132 gpm)
Reject water volume per flush cycle (at 2 bar - 30 psi)
15 liter(4 gallon)
20 liter(5.2 gallon)
28 liter(7.3 gallon)
125 liter(33 gallon)
150 liter(40 gallon)
Flushing cycle time 10 seconds 15 seconds
Exhaust valve 1.5" (40 mm)
Flushing criteria Differential pressure of 0.5 bar (7 psi), time intervals or manual operation
Screen Data
Total filtration area1,300 cm²(202 in²)
2,120 cm²(329 in²)
3,000 cm²(465 in²)
6,150 cm²(953 in²)
8,890 cm²(1,378 in²)
Net filtration area750 cm²(116 in²)
1,500 cm²(232 in²)
2,250 cm²(349 in²)
4,500 cm²(698 in²)
6,800 cm²(1,054 in²)
Screen types Molded weavewire stainless steel 316L
* Construction Materials
Filter housing Epoxy-coated carbon steel 37-2 (stainless steel 316L on request)
Filter lid High density polypropylene, Epoxy coated carbon steel 37-2 (Stainless steel 316L on request)
Cleaning mechanism PVC and stainless steel 316L
Exhaust valve Brass, stainless steel 316L, BUNA-N
Seals BUNA-N
Control Brass, stainless steel 316L, and acetal
* Amiad offers a variety of construction materials. Consult us for specifications.
Technical Specifications - M100 Models
Filter Model MG110 MG112 MG114
General Data
Maximum flow rate* 400 m³/h(1,760 gpm)
600 m³/h(2,640 gpm)
800 m³/h(3,520 gpm)
Inlet/Outlet diameter 10” (250 mm) 12” (300 mm) 14” (350 mm)
Standard filtration degrees 500, 300, 200, 130, 100, 80 micron
Minimum workingpressure
2 bar (30 psi)For lower pressure please consult Amiad
Maximum working pressure 10 bar (150 psi)
Maximum working temperature 55°C (131°F)
Weight [empty]325 kg(717 lb)
480 kg(1,054 lb)
723 kg(1,590 lb)
* Consult Amiad for optimum flow depending on filtration degree and water quality.
Flushing Data
Minimum flow for flushing(at 2 bar - 30 psi)
30 m³/h(132 gpm)
Reject water volumeper flush cycle (at 2 bar - 30 psi)
300 liter(80 gallon)
450 liter(120 gallon)
600 liter(160 gallon)
Flushing cycle time 30 seconds 45 seconds 60 seconds
Exhaust valve 1.5" (40mm)
Flushing criteria Differential pressure of 0.5 bar (7 psi), time intervals or manual operation
Screen Data
Total filtration area17,780 cm²(2,756 in²)
26,670 cm²(4,134 in²)
35,560 cm²(5,512 in²)
Net filtration area13,600 cm²(2,108 in²)
20,400 cm²(3,162 in²)
27,200 cm²(4,216 in²)
Screen types Molded weavewire, stainless steel 316L
* Construction Materials
Filter housing Epoxy-coated carbon steel 37-2 (stainless steel 316L on request)
Filter lid High density polypropylene, Epoxy coated carbon steel 37-2 (Stainless steel 316L on request)
Cleaning mechanism PVC and stainless steel 316L
Exhaust valve Brass, stainless steel 316L, BUNA-N
Seals BUNA-N
Control Brass, stainless steel 316L, and acetal
* Amiad offers a variety of construction materials. Consult us for specifications.
Technical Specifications - MG Models
910101-000392/11.2017
The Americas Amiad USA Inc. Main Office and Manufacturing: 120-J Talbert Road, Mooresville, NC 28117,Tel: +1 704 662 3133, Fax: +1 704 662 3155, Toll Free: +1 800 24 FILTER, E-mail: [email protected] www.amiadusa.com
West Coast Sales Office and Warehouse:1251 Maulhardt Ave, Oxnard, CA 93030Tel: 1 805 988 3323, Fax: 1 805 988 3313, Toll Free: 1 800 969 4055
BrazilAmiad Sistemas de Água Ltda., Rua Funchal, 411, Conj. 42, Vila Olimpia, São Paulo, CEP 04551-060Tel: +55 11 31923824, E-mail: [email protected] Oil & Gas, E-mail: [email protected]
MexicoAmiad México SA DE CV, AV. Jesus del Monte #39B – INT 601, Col. Jesus del Monte, C.P. 52764, Huixquilucan, Estado de México, Tel/Fax: +52 55 636 28122, Mob: +52 1 55 4909 2202E-mail: [email protected]
Irrigation Office: Ing. Ramón Padilla Sanchez 1000 A, Col. Venta del Astillero, Zapopan, C.P. 45221, Jalisco – Mexico, Tel: +52 1 33 3640 0189 / +52 1 33 3641 4943, E-mail: [email protected]
Amiad Water Systems Europe SAS, Ilot No4 ZI La Boitardière, 37530 Chargé, France,Tel: +33 (0) 2 47 23 01 10, Fax: +33 (0) 2 47 23 80 67, E-mail: [email protected] Water Systems Europe SAS (Irrigation Division) 100 avenue de l’Anguillon, Z.I. des Iscles, 13160 Chateaurenard, Tel: +33 (0) 4 32 60 10 01, Fax +33 (0) 4 32 60 60 85
GermanyAmiad Water Systems SAS Europe (German branch office) Zweigniederlassung Deutschland Prinz-Regent-Str. 68 a 44795 Bochum,Tel: +49 (0) 234 588082-0, Fax: +49 (0) 234 588082-10, E-mail: [email protected]
United KingdomAmiad Water Systems UK Limited, Unit 1 Heol Rhosyn, Dafen Business Park, Dafen, Llanelli SA14 8QG,Tel: +44 (0)1792 277290, Fax: +44 (0)1792 797707, E-mail: [email protected]
Europe
IndiaAmiad Filtration India Pvt Limited, 305 Sai Commercial Building, Govandi St Rd, Govandi Mumbai 400 088, Tel: +91 22-67997813/14, Fax: +91 22-67997814, Email: [email protected] China (Yixing Taixing Environtec Co., Ltd.) 70 Baihe Chang, Xingjie Yixing Jiangsu, 214204,Tel: +86 510 87134000, Fax: +86 510 87134999, E-mail: [email protected] AsiaFiltration & Control Systems Pte. Ltd., 22 Sin Ming Lane #07-71 Midview City, Singapore 573969, Tel: +65 6 337 6698, Fax: +65 6 337 8180, E-mail: [email protected]
Asia
Amiad Australia Pty Ltd. 138 Northcorp Boulevard, Broadmeadows, Victoria 3047,Tel: +61 3 93585800, Fax: +61 3 93585888, E-mail: [email protected]
Australia
Amiad Water Systems Ltd. D.N. Galil Elyon 1, 1233500, Israel,Tel: +972 4 690 9500, Fax: +972 4 814 1159,E-mail: [email protected]
Headquarters
www.amiad.com
Copyright © 2013 Amiad Water Systems Ltd. All rights reserved. The contents of this catalogue including without limitation all information and materials, images, illustrations, designs, icons, photographs, graphical presentations, designs, literary works, data, drawings, slogans, phrases, names, trademarks, titles and any other such materials that appear in this catalogue (collectively, the “Contents”) are the sole property of Amiad Water Systems Ltd. (“Amiad”). Amiad has sole and exclusive right, title and interest in the Contents, including any intellectual property rights, whether registered or not, and all know-how contained or embodied therein. You may not reproduce, publish, transmit, distribute, display, modify, create derivative works from, sell or participate in any sale of, or exploit in any way, in whole or in part, any of the Contents or the catalogue. Any use of the catalogue or the Contents, other than for personal use, requires the advanced written permission of Amiad.