Finepix S1000 Service Manual

Condential: FUJIFILM Service Center Use Only

DIGITAL CAMERA

FinePix S1000fdUS/EU/E1/EG/EE/CH-model

SERVICE MANUAL

CAUTION BECAUSE THIS PRODUCTIS RoHS LEAD-FREE COMPLIANT, USE THE DESIGNATED AFTER-SELES PARTS AND THE DESIGNATED LEAD-FREE SOLDER WHEN PERFORMING REPAIRS. (Refer to page 3 to page 5)

WARNING THE COMPONENTS IDENTIFIED WITH THE MARK " " ON THE SCHEMATIC DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR SAFETY. PLEASE REPLACE ONLY WITH THE COMPONENTS SPECIFIED ON THE SCHEMATIC DIAGRAM AND IN THE PARTS LIST. IF YOU USE PARTS NOT SPECIFIED, IT MAY RESULT IN A FIRE AND AN ELECTRICAL SHOCK.

Ref.No.: ZM00722-101

Printed in Japan 2008.12

Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual

SAFETY CHECK-OUTAfter correcting the original problem, perform the following safety check before return the product to the customer.1. Check the area of your repair for unsoldered or poorly soldered connections. Check the entire board surface for solder splasher and bridges. 2. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. 3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. 4. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 5. Check the B + voltage to see it is at the values specied. 6. Make leakage - current measurements to determine that exposed parts are acceptably insulated from the supply circuit before returning the product to the customer.RISK OF FIREREPLACE FUSE AS MARKED

7.

CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH SAME TYPE 2.5 AMPERES 125V FUSE. ATTENTION: AFIN D'ASSURER UNE PROTECTION PERMANENTE CONTRE LES RISQUES D'INCENDIE, REMPLACER UNIQUEMENT PAR UN FUSIBLE DE MEME, TYPE 2.5 AMPERES, 125 VOLTS. WARNING: TO REDUCE THE ELECTRIC SHOCK, BE CAREFUL TO TOUCH THE PARTS.

2.5A 125V2.5A 125V

8.

WARNING!HIGH VOLTAGE

2


RoHS lead-free complianceBecause this product is RoHS lead-free compliant, use the designated after-sales parts and the designated lead-free solder when performing repairs.

With the exception of parts and materials expressly excluded from the RoHS directive(*1), all the internal connections and component parts and materials used in this product are lead-free compliant(*2) under the European RoHS directive. *1: Excluded items (list of the main lead-related items) Lead included in glass used in uorescent tubes, electronic components and cathode-ray tubes Lead in high-melting-point solder (i.e. tin-lead solder alloys that contain 85% lead or more) Lead in ceramic electronic parts (piezo-electronic devices) Mercury contained in uorescent tubes is also excluded. *2: Denition of lead-free A lead content ratio of 0.1 wt% or less in the applicable locations (solder, terminals, electronic components, etc.) RoHS: Designated substances (6):

The name of a directive issued by the European Parliament aimed at restricting the use of certain designated hazardous substances included in electrical and electronic equipment. Lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBBs) and polybrominated diphenyl ether (PBDE)

When carrying out repairs, use a designated lead-free solder, bearing in mind the differing work practices for conventional solder (eutectic) and lead-free solder.

Differences in the soldering work for lead-free and eutectic solder

When the soldering work practices for eutectic solder and lead-free solder are compared, the main differences are as shown below. In particular, when lead-free solder is used, the solder tends to be less workable than when eutectic solder is used. Accordingly, the soldering techniques used must take that into account. Difference Countermeasure The initial melting point of lead-free solder is high, so you have to get used to it. Move the tip of the soldering iron around to heat the entire connection to the melting temperature and assist wetting. Use the solder (wire) diameter and soldering iron that are best suited to connection being soldered. First apply solder to the area immediately around the through hold and then feed the solder into the hole. Use a suitable wicking wire (with a suitable method and heating) and a suction tool. Either put solder onto the soldering iron tip after completing the work, or turn the iron off frequently. Learn to recognize the appearance of the surface. The solder starts melting later. Poor wetting Solder feed rate is difcult to control. Wetting the insides of through holes is especially difcult. During repairs (or modications) removing solder from inside through holes is difcult. There is serious carbonization of the soldering iron. The surface is not glossy.

1 2 3 4 5 6 7

3

Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual Setting temperature during lead-free soldering Lead-free solder melting temperature The melting point of eutectic (Sn-Pb) solder is 183C, while the melting point of lead-free solder (Sn-Ag-Cu) is 30C higher at 220C.

Soldering iron tip temperature The temperature setting for the soldering iron used should be such that the tip of the soldering iron is at the correct bonding temperature for the connection. This temperature is normally set at around 100C higher than the melting point of the solder. However, the actual temperature should take into account the shape and size of the soldering iron tip, the heat tolerance of the connection and the workability of that temperature. Correct bonding temperature The correct bonding temperature refers not to the temperature of the heat source, but to the bonding temperature that will give the best bond strength.

Precautions when soldering with lead-free solder

Soldering iron maintenance Because of the high soldering iron temperature in lead-free soldering, there is rapid carbonization of the ux adhering to the tip of the soldering iron. (1) Always cover the tip of the soldering iron with solder when it is not being used. (2) If the tip is black from carbonization, wipe it gently with a paper towel soaked in alcohol until the solder will wet.

Uniform heating of the board and components To ensure that the lead-free solder wets the entire surface of the pattern and the lands despite its poor wetting characteristics, you must move the tip of the soldering iron over a wide area to raise the temperature of the entire connection.

Soldering iron

A soldering iron with a temperature control is best.

4

Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual Solder wire (thread)Use the lead-free solders specied below. Solder type: Sn96.5Ag3Cu0.5 (Displayed symbol: SnAgCu) Wire diameter: 0.6, 0.8 or 1.0 mm Sample:

lead-free

Wire diameter 0.8mm Solder type (Displayed symbol) SnAgCu

Flux

Conventional ux can be used.

Solder application wires (mesh, wicking wire, etc.)Conventional application wires can be used.

5


MEMO

6


CONTENTS

CONTENTS1. General ....................................................... 1-1 3. Schematics ................................................. 3-1

1-1. Product specication............................................1-1 1-2. Explanation of Terms ...........................................1-5 1-3. Names of External Components ..........................1-6

2. Disassembly ............................................... 2-12-1. 2-2. 2-3. 2-4. 2-5.

Names of internal Components ...........................2-1 Removing the BACK COVER CONST ................2-2 Disassembling the BACK COVER CONST .........2-2 Removing the LCD and TOP COVER CONST ....2-3 Disassembling the TOP COVER CONST ............2-5 2-5-1. Removing the MODE DIAL and other operation buttons ...................................2-5 2-5-2. Removing the EVF and FLASH unit.......2-7 2-6. Removing the MAIN PWB ASSY .........................2-9 2-7. Removing the LENS CONST...............................2-9 2-8. Removing the BATTERY PWB ASSY and main capacitor ...................................................2-10 2-9. Disassembling the FRONT COVER CONST ..... 2-11 2-10. Installation locations for the SEAL and MYLAR .......................................2-12 2-10-1. Attaching the KEY SHEET METAL MYLAR to the KEY SHEET METAL ......................2-12 2-10-2. Attaching the TOP COVER MYLAR to the TOP FPC UNIT ..............................2-12 2-10-3. Attaching the FLASH DETECT WIRE MYLAR to the FLASH DETECT WIRE UNIT ........2-13 2-10-4. Attaching the FLASH SPONGE to the TOP COVER ..................................2-13 2-10-5. Attaching the CAP. MYLAR B to the MAIN FRAME.................................2-13 2-10-6. Attaching the CAP. MYLAR A and BATTERY SEAL to the BATTERY PWB ASSY ...................2-14 2-10-7. Afxing the LCD HOLDER MYLAR to the LCD HOLDER ................................2-14 2-10-8. Attaching the CAP. MYLAR A to the LCD ................................................2-14 2-10-9. Attaching the BATTERY SEAL, LENS FPC SPONGE and TAPE GASKET to the MAIN PWB ASSY...........................2-15 2-10-10. Attaching the DUST PROOF SPONGE to the LENS RING ....................................2-15

3-1. Cautions...............................................................3-1 3-2. Basic Block Names and Functions ......................3-1 3-3. Description of Main Block Functions....................3-2 3-3-1. Technical Overview ................................3-2 3-3-2. Explanation of each block ......................3-2 3-4. Block Diagram .....................................................3-3 3-5. Overall connection Diagram ................................3-4 3-6. Circuit Diagrams ..................................................3-5 3-6-1. BATT BOARD BLOCK ...........................3-5 3-6-2. CCD 3 in 1 BLOCK ................................3-6 3-6-3. CCD FPC BLOCK ..................................3-7 3-6-4. DDR+NAND/SD CARD BLOCK .............3-8 3-6-5. DSP BLOCK ...........................................3-9 3-6-6. KEY FPC BLOCK .................................3-10 3-6-7. LCD EVF USB LED AUDIO IN PORT BLOCK ................................. 3-11 3-6-8. MOTOR BLOCK ...................................3-12 3-6-9. POWER BLOCK ..................................3-13 3-6-10. TOP FPC BLOCK ................................3-14 3-7. Mounted Parts Diagrams ...................................3-15 3-7-1. BATTERY BOARD ASSY .....................3-15 3-7-2. AF LED ASSY ......................................3-17 3-7-3. CCD FPC ASSY ...................................3-17 3-7-4. MAIN BOARD ASSY ............................3-18 3-7-5. FLASH BOARD ASSY .........................3-20 3-7-6. TRIGGER BOARD ASSY.....................3-20 3-7-7. KEY FPC ASSY ...................................3-20 3-7-8. TOP FPC ASSY ...................................3-21

7

CONTENTS


CONTENTS4. Adjustments ............................................... 4-1 5. Inspection ................................................... 5-1

4-1. Important point before adjustment .......................4-1 4-1-1. The handling of image les in internal memory .....................................4-1 4-1-2. Adjustment when replacing major parts..............................4-2 4-2. Measuring instruments used................................4-2 4-3. Use jig list ............................................................4-2 4-4. Calibration method of pattern box........................4-3 4-5. Preparation of Adjustment Software ....................4-4 4-5-1. Various downloading software decompressions, preservation methods, and notes ...........4-4 4-5-2. Explanation of the "MENU" Adjustment Software ..........4-5 4-6. MAIN PWB Initialize.............................................4-7 4-7. Self test & Lens test .............................................4-9 4-8. End Voltage Adjustment..................................... 4-11 4-9. AF Adjustment ...................................................4-13 4-10. Shutter Adjustment ............................................4-16 4-11. ISO Sensitivity Adjustment.................................4-18 4-12. CCD Defect Correction ......................................4-20 4-13. Color Correction.................................................4-22 4-14. Flash Adjustment ...............................................4-24 4-15. Preparation of FxS1000fd USB ID Writing Software .................4-26 4-15-1. Various downloading software decompressions, preservation methods, and notes .........4-26 4-16. USB_ID Writing ..................................................4-27 4-17. Langeuage Setting.............................................4-34

5-1. Required Measuring Equipment ..........................5-1 5-2. Connection of Measuring Equipment...................5-1 5-3. Inspection and Factory Settings ..........................5-2

6. Parts List .................................................... 6-1

6-1. Packing and Accessories .....................................6-1 6-1-1. US-model ...............................................6-1 6-1-2. EU-model ...............................................6-2 6-1-3. E1-model ................................................6-3 6-1-4. EG-model ...............................................6-4 6-1-5. EE-model ...............................................6-5 6-1-6. CH-model ...............................................6-6 6-2. FRONT COVER CONST .....................................6-7 6-3. BATTERY COVER CONST .................................6-8 6-4. MECHANICAL BLOCK ........................................6-9 6-5. TOP COVER CONST ........................................6-10 6-6. Electrical parts ................................................... 6-11

7. Appendix .................................................... 7-1

7-1. List of Related Technical Updates Issued ............7-1

8


1. General

1. General1-1.System

Product specicationDigital camera FinePix S1000fd 10.0 million pixels 1/2.3-inch CCD Internal memory (approx. 24 MB)/xD-Picture Card (16/32/64/128/256/512 MB/1 GB/2 GB)/ SD/SDHC Memory Card (FUJIFILM recommendation) Still image: DCF-compliant Compressed: Exif ver.2.2 JPEG, DPOF-compatible *Design rule for Camera File System compliant/DPOF compatible Movie: AVI format, Motion JPEG Audio: WAVE format, Monaural sound

Model Effective pixels CCD Storage media File format

Number of recorded pixels

Still image: 3648 2736 pixels/3648 2432 pixels/2592 1944 pixels/2048 1536 pixels 1600 1200 pixels/640 480 pixels ( /%/[/3/2/`)

Lens Focal length Digital zoom Aperture Focal range (from lens surface)

Fujinon 12 optical zoom lens F2.8 (Wide-angle)-F5.0 (Telephoto) f=5.9 mm-70.8 mm (Equivalent to approx. 33 mm-396 mm on a 35 mm camera) Approx. 5.7 (12 optical zoom lens is used together: Max. zoom scale: approx. 68.4) F2.8-F6.4 (Wide-angle) to F5.0-F8.0 (Telephoto) in 1/3 EV increments Manual/ Auto selectable Normal: Wide-angle: approx. 40 cm (1.3 ft.) to infinity (In High-speed shooting mode: approx. 1.5 m (4.9 ft.) to infinity) Telephoto: Macro: approx. 1.5 m (4.9 ft.) to infinity (In High-speed shooting mode: approx. 2.0 m (4.9 ft.) to infinity) Wide-angle: 5 cm to 3.0 m (11.7 in. to 9.9 ft.) Telephoto: 80 cm to 9.9 m (2.6 ft. to 11.5 ft.)

Super macro: Approx. 2 cm to 10 cm (0.4 in. to 3.9 in.) Focal length: fixed to approx. 60 mm (35 mm camera equivalent) Sensitivity Photometry Exposure control Scene position [AUTO]/[AUTO(400)]/[AUTO(800)]/Equivalent to ISO [64]/[100]/[200]/[400]/[800]/[1600]/ [3200] (max. number of recorded pixels:3) (Standard output sensitivity) TTL 256-zones metering Multi, Spot, Average Program AE (When using P mode : Program Shift is enabled)/Shutter priority AE/Aperture priority AE/Manual exposure ([NATURAL LIGHT]), H ([PORTRAIT]), , ([LANDSCAPE]), . ([SPORT]), / ([NIGHT]), ([MUSEUM]), Intelligent Face Detection Exposure compensation Available 2 EV to +2 EV in 1/3 EV-step increments (N, To prevent accidental erasure, carry out this step not only when the MAIN PWB ASSY is replaced but in all cases. *Note For PTP-connected cameras, carry out the procedure in "ii. Procedure for PTP-connected cameras and images that cannot be downloaded to a PC". I. Procedure when images can be downloaded to a PC * If an xD-Picture card is inserted, data in the internal memory cannot be backed up. (1) Back up the images stored in internal memory. Create a folder (named and located so as to avoid any confusion with the user's images). Without inserting an xD-Picture card, connect the camera to a PC and copy the image les on the removable disk recognized by the PC to the folder created in the previous step. Check that the images can be displayed correctly on the PC. (2) Return the backed up image les from the PC to the camera. Turn the camera on without an xD-Picture card inserted and format the camera's internal memory. Without inserting an xD-Picture card, connect the camera to the PC and copy the image les from the folder containing the images backed up in the previous step onto the removable disk recognized by the PC. Check that the images can be displayed correctly on the camera. Delete the backup les created on the PC in step (1) (the user's image les). II. Procedure when images cannot be downloaded to a PC (1) Back up the images stored in internal memory. Insert an xD-Picture card to be used for image backup into the camera and format the card. From the SETUP menu, reset the frame numbers. Select image copying from the playback menu, select "Camera -> Card" for all the frames and then copy the images. Check that the images can be displayed correctly on the camera. (2) Return the backed up image les from the xD-Picture card to the camera. Before inserting the card, format the camera's internal memory. Insert the xD-Picture card containing the backed up copies of the user's image les. From the SETUP menu, reset the frame numbers. Select image copying from the playback menu, select "Card -> Camera" for all the frames and then copy the images. Remove the xD-Picture card and check that the images can be displayed correctly on the camera. From the SETUP menu, set the frame numbers to the default sequence. If the image le numbers have changed, always notify the user in writing that the image le numbers have changed. III. Procedure for PTP-connected cameras and images that cannot be downloaded to a PC (Images can only be backed up to a PC. * Normally, back up images using procedure II.) (1) Back up the images stored in the camera's built-in memory. Create an FAIS receive number folder (to ensure error-free user image management). Without inserting an xD-Picture card, connect the camera to the PC and check the image les in the camera on the PC. Then copy those les to the folder described on the previous page. Check that the images can be viewed successfully on the PC. (2) Return the backup image les from the PC to the camera. With no xD-Picture card inserted, turn the camera on and format the built-in memory. Using a card reader or similar device, check the xD-Picture card to be used for image le backup on your PC. Copy the image les from the image le backup folder on the previous page into the "DCIM\100_FUJI\" folder on the image le backup xD-Picture card. Using a safe procedure, remove the image le backup xD-Picture card from your PC. Load the image le backup xD-Picture card into the camera. Select "Copy image" in the Playback menu, select all the frames in "Card -> Camera" and then copy the images. Remove the xD-Picture card and check that the images can be viewed successfully. Delete the backup les (user image les) created on the PC in step (1).

4-1

4. Adjustments4-1-2. Adjustment when replacing major partsReplacing parts Adjustment item MAIN PWB Initialize * Self test & Lens test End Voltage Adjustment AF Adjustment Shutter Adjustment ISO Sensitivity Adjustment CCD Defect Correction Color Correction Flash Adjustment USB_ID Writing Language Setting


Adjust the item shown by in the table below at the part replacement of LENS CONST, MAIN PWB ASSY, BATTERY PWB ASSY, FLASH BOTTOM ASSY (Other part replacements need not be adjusted). No. 0 1 2 3 4 5 6 7 8 9 10 LENS CONST MAIN PWB ASSY BATTERY PWB ASSY FLASH BOTTOM ASSY

* If the MAIN PWB ASSY has been replaced, upgrade the MAIN PWB Initialize before carrying out all the adjustments. Because the internal memory is formatted during the "MAIN PWB Initialize" procedure, take particular not to erase customer data when working on repair products.

4-2.

Measuring instruments usedRemarks For adjustment Used for USB ID Write and operation checks (PC-AT compatible) OS: Win 2000, XP LS-110 (Minolta) or equivalent Color Meter IIIF (Minolta) or equivalent PTB450F

Measuring equipment Regulated power supply PC Brightness meter Color temperature meter Pattern box

4-3.

Use jig listName LB140 lter EFA chart Close_up lens (f=500mm) Power Cable Jig DC COUPLER CP-04 Gray chart FinePixS1000fd_USB_ID FinePixS1000fd W PC Soft Ver.1.00 Lens holder Stand X-Y stage for AF adjustment Screw Driver (D3LUFX88G(2X20)) LB140 lter holder kit for X-Y stage Discharger AF solid chart USB cable Comment ISO Sensitivity Adjustment AWB Adjustment AF Adjustment AF Adjustment General sdjustment General sdjustment Flash Adjustment USB_ID Writing General sdjustment AF Adjustment AF Adjustment General sdjustment General repair General sdjustment Discharger for FLASH UNIT General sdjustment USB_ID Writing Remarks Common with the DS-30/DS-20/DS-7 Common with the FinePix A345/ FinePix A350/FinePix A370 Common with the FinePix F402 Common with the FinePix S304 New jig Common with the FinePix A345/ FinePix A350/FinePix A370 New jig (downloaded from WEB.) New jig (downloaded from WEB.) Common with the FinePix M603 Common with the FinePix M603 Common with the FinePix M603 Common with the FinePix M603 Common with the FinePix M700 Common with the FinePix S304 Common with the FinePix S2Pro This is bundled to the product

Pats.No ZJ00006-100 DC-R-J ZJ00615-100 ZJ00580-100 CR0130900U9 DC-R-K ZJ01692-100 ZJ01169-100 ZJ00008-100 ZJ00009-100 ZJ00611-100 ZJ00583-100 ZJ00653-100 ZJ00581-100 ZJ00553-100 CR013084899

4-2


4. Adjustments

4-4.

Turn on the power supply in the pattern box. Afterwards, wait for about ten minutes so that the source of light may stabilize.

Calibration method of pattern box

Pattern BOX (All white)

(1) Brightness 160 5 cd/m2 (with LB140 lter) No chart, center of pattern box Minolta brightness meter LS-110 or equivalent * Calibration method Place the lter (LB140) against the pattern box. With the lter (LB140) in contact with the brightness meter, adjust the pattern box brightness to 160 5 cd/m2.

LB140

(2) Color temperature 6100 50 K (with LB140 lter) No chart, center of pattern box Minolta color meter IIIF or equivalent * Calibration method Place the lter (LB140) against the pattern box. With the lter (LB140) in contact with the color temperature meter, adjust the pattern box color temperature to 6100 50 K.

4-3

4. Adjustments4-5.4-5-1.The PC adjustment softwares are in a specied Web server, and both of these are the compression of ZIP form les. Therefore, after downloading these compression les from the Web server, the decompression of the le is necessary. In the decompression software, if the decompression of the ZIP form can be done, any software is OK. (Please prepare each one for the decompression software.) The decompression and the preservation method of the PC adjustment software and the rmware are described to the following. * The adjustment soft decompression and set up the adjustment card. The adjustment software is downloaded from WEB, and software is installed in the PC. We have uploaded the ZJ01169-100.zip on our website: (https://denhin.fujilm.co.jp/csg_en/index.htm).


Preparation of Adjustment Software

Various downloading software decompressions, preservation methods, and notes

FinePixS1000fd W PC Soft Ver.1.00

ZJ01169-100.zip

Screen

ZJ01169-100 is a compression of ZIP type le.(Figure. 4-5-2). Copy the "menu" le and "Firmware" folder in the "ZJ01169-100" folder to an xD-Picture card.(Figure. 4-5-3).

My Computer 3.5inch FD(A:) (C:) ZJ01169-100 menu Firmware Firmware.bin

My Computer 3.5inch FD(A:) (C:) Removable disk menu Firmware Firmware.bin

4-4

Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual4-5-2. Explanation of the "MENU" Adjustment Software

4. Adjustments

Use the adjustment xD-Picture card created in section 4-5-1 above to carry out adjustments on this model. Insert the adjustment xD-Picture card containing the "MENU" adjustment software into the camera's card slot and turn the camera on. The adjustment software launches automatically. [Operation guide] 4-way button: Selects items to be adjusted. MENU/OK button: Executes an adjustment. [Note] Only the adjustments shown in to are used. Do not select or execute any other adjustments.

MAIN PWB Initialize Self test & Lens test

End Voltage Adjustment

AF Adjustment

4-5

4. AdjustmentsShutter Adjustment ISO Sensitivity Adjustment CCD Defect Correction Color Correction Flash Adjustment


Language Setting (US-model) Language Setting (EU/EG/EE-model) Language Setting (CH-model)

USB_ID Write

4-6


4. Adjustments

4-6.

[Note] Only when the MAIN PWB ASSY has been replaced,always carry out the "MAIN PWB Initialize" procedure before performing any other adjustments. Because the internal memory is formatted during the "MAIN PWB Initialize" procedure, take particular not to erase customer data when working on repair products. (Because the inspection image from the MAIN PWB ASSY manufacturing process may be contained in the internal memory, check that the memory has been erased after "MAIN PWB Initialize".)

MAIN PWB Initialize

FinePix S1000fd

DC COUPLER CP-04

AC Power Adapter

Insert the adjustment xD-Picture card into the camera, set the Mode dial to "AUTO" and then turn the camera on. When the screen shown on the right appears, press the Right button.

4-7

4. Adjustments


Press the Down button to select "UPdate FW" and then press the MENU/OK button.

When the screen shown on the right appears, press the Up button.

The indicator lamp starts ashing green and when MAIN PWB Initialize ends, the camera turns off. [Note] Do not turn the camera off while the indicator lamp is ashing. --> MAIN PWB Initialize ends.

4-8


4. Adjustments

4-7.

Position the camera and the Gray chart so that the chart is180 20 mm from the front of the camera lens. Gray chart

Self test & Lens test

Insert the adjustment xD-Picture card into the camera, set the Mode dial to "AUTO" and then turn the camera on. When the screen shown on the right appears, press the Right button.

Camera

Center

180mm20mm

4-9

4. Adjustments Press the Down button to select "Self Test" and then press the MENU/OK button.


If the "PASS" screen appears, turn the camera off and remove the xD-Picture card. If "FAIL" appears, check the settings and carry out the adjustments again.

-->Self test & Lens test ends.

4-10


4. Adjustments

4-8.

FinePix S1000fd

End Voltage Adjustment

DC COUPLER CP-04 Regurated Power supply

Digital voltmeter

POWER CABLE JIG

Set the digital voltmeter to voltage measurement mode and then connect it to the Power Cable Jig clip. After checking the digital voltmeter and setting the regulated power supply to 5.0 V, plug the DC COUPLER into the camera. Insert the adjustment xD-Picture card into the camera, set the Mode dial to "AUTO" and then turn the camera on. Adjust the voltage from the regulated power supply until 4.44V0.02V is displayed on the digital voltmeter.

4-11

4. Adjustments When the screen shown on the right appears, press the Right.


Press the Down button to select "Batt Check" and then press the MENU/OK button.

If the screen shown below (Figure. 4-8-1) appears, turn the camera off and remove the adjustment xD-Picture card. If "FAIL" (Figure. 4-8-2) appears, check the settings and carry out the adjustments again.

--> End Voltage Ajdustment ends.

4-12


4. Adjustments

4-9.

(1) Set up the EFA chart and conversion lens so that they are 500 5 mm apart. (2) Position the chart so that the brightness of the chart surface is between 1000 200 LUX. (3) Position the 500 mm conversion lens 25 2 mm from the front end of the lens.Lens Holder Attention when conversion lens is used. Convex side : Subject side. Plane : Camera lens side.

AF Adjustment

252 mm with the zoom set to wide. Note that the camera lens should not touch the conversion lens.Fluorescent light stand EFA chart

Lens Stand

Washer (Plastic)Lens Base Plate

Fixed Ring

Center

Insert the adjustment xD-Picture card into the camera, set the Mode dial to "AUTO" and then turn the camera on.

Camera

500mm conversion lens

500 5 mm

4-13

4. Adjustments When the screen shown on the right appears, press the Down button to change to "2".


When the screen shown on the right appears, press the Right button.

Press the Down button to select "EFA In" and then press the MENU/OK button.

4-14

Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual If the "PASS" screen appears, turn the camera off and remove the xD-Picture card. If "FAIL" appears, check the settings and carry out the adjustments again.

4. Adjustments

--> AF Adjustment ends.

4-15

4. Adjustments4-10. Shutter Adjustment


[Notes] Darken the surroundings during calibration (a darkroom environment is ideal). Alternatively, prepare a box that is painted black on the inside and perform the adjustments with the camera enclosed in the box. Calibrate the pattern box before the adjustment. Any soiling on the pattern box dispersion plate or reective plate will result in unevenness in the lighting and cause errors during adjustment. Take care to carry out periodic pattern box cleaning and testing. Maximum 5mm

Centerline

Insert the adjustment xD-Picture card into the camera, set the Mode dial to "AUTO" and then turn the camera on. When the screen shown on the right appears, press the Down button to change to "5".

Camera

Pattern box

Remove the LB140 lter.

4-16

Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual When the screen shown on the right appears, press the Right button.

4. Adjustments

Select "Cali Shutter" and press the MENU/OK button.


-->Shutter Adjustment ends.

4-17

4. Adjustments4-11. ISO Sensitivity Adjustment


[Notes] Darken the surroundings during calibration (a darkroom environment is ideal). Alternatively, prepare a box that is painted black on the inside and perform the adjustments with the camera enclosed in the box. Calibrate the pattern box before the adjustment. Any soiling on the pattern box dispersion plate or reective plate will result in unevenness in the lighting and cause errors during adjustment. Take care to carry out periodic pattern box cleaning and testing. Maximum 5mm

Centerline


Camera

Pattern box

LB140

4-18


4. Adjustments

Press the Down button to select "ISO" and then press the MENU/OK button.


-->ISO Sensitivity Adjustment ends.

4-19

4. Adjustments4-12. CCD Defect Correction


[Note] Darken the surroundings during calibration (a darkroom environment is ideal). Alternatively, prepare a box that is painted black on the inside and perform the adjustments with the camera enclosed in the box. Calibrate the pattern box before the adjustment. Any soiling on the pattern box dispersion plate or reective plate will result in unevenness in the lighting and cause errors during adjustment. Take care to carry out periodic pattern box cleaning and testing. Maximum 5mm

Centerline


Camera

Pattern box

Remove the LB140 lter.

4-20


4. Adjustments

Press the Down button to select "Bad Pixel" and then press the MENU/OK button.


--> CCD Defect Correction ends.

4-21

4. Adjustments4-13. Color Correction


[Note] Darken the surroundings during calibration (a darkroom environment is ideal). Alternatively, prepare a box that is painted black on the inside and perform the adjustments with the camera enclosed in the box. Calibrate the pattern box before the adjustment. Any soiling on the pattern box dispersion plate or reective plate will result in unevenness in the lighting and cause errors during adjustment. Take care to carry out periodic pattern box cleaning and testing. Maximum 5mm

Centerline


Camera

Pattern box

LB140

4-22


4. Adjustments

Press the Down button to select "Color" and then press the MENU/OK button.


--> Color Correction ends.

4-23

4. Adjustments4-14. Flash Adjustment


[Note] Darken the surroundings during calibration (a darkroom environment is ideal). Adjust the positions so that the distance from the gray chart to the camera's ash unit is 280 10 mm.

280 10 mm

Centerline


Camera

Gray chart

4-24


4. Adjustments

Press the Down button to select "Cali Flash" and then press the MENU/OK button.


--> Flash Adjustment ends.

4-25

4. Adjustments4-15.4-15-1.The PC adjustment softwares are in a specied Web server, and both of these are the compression of ZIP form les. Therefore, after downloading these compression les from the Web server, the decompression of the le is necessary. In the decompression software, if the decompression of the ZIP form can be done, any software is OK. (Please prepare each one for the decompression software.) The decompression and the preservation method of the PC adjustment software and the rmware are described to the following. * The adjustment soft decompression and set up the adjustment card. The adjustment software is downloaded from WEB, and software is installed in the PC. We have uploaded the ZJ01692-100.zip on our website: (https://denhin.fujilm.co.jp/csg_en/index.htm). ZJ01692-100 is a compression of ZIP type le.


Preparation of FxS1000fd USB ID Writing Software

Various downloading software decompressions, preservation methods, and notes

FxS1000fd USB ID Writing Software

ZJ01692-100.zip

Screen

The FinePixS1000fd_USB_ID folder can be done by extracting it by Compression software. Copy the FinePixS1000fd_USB_ID folder to the C drive on the Adjustment PC.

My Computer 3.5inch FD(A:) (C:) ZJ01692-100 FinePixS1000fd_USB_ID

My Computer 3.5inch FD(A:) (C:) ZJ01692-100 FinePixS1000fd_USB_ID

4-26


4. Adjustments

4-16.

Double-click "tool.exe" in the C:\FinePixS1000fd_USB_ID folder.

USB_ID Writing

When the window shown below appears, click the "OK" button.

The software shown below starts up.

4-27

4. Adjustments When the screen shown on the right appears, press the Down button to change to "8".


Insert the adjustment xD-Picture card into the camera, set the Mode dial to "AUTO" and then turn the camera on.

When the screen shown on the right appears, press the Right button. select "USB SERIAL NUMBER", and press the MENU/OK button.

When the screen shown on the right appears, connect the USB cable to the PC.

4-28


4. Adjustments

In the "Welcome to the Found New Hardware Wizard" window, select "Install from a list or specic location (Advanced)" and then click "Next".

When the detection wizard window appears, click "Browse" button.

4-29

4. Adjustments


When the "Browse Folder" window appears, select one of the following and click the "OK" button. In Windows XP, select the C:\FinePixS1000fd_USB_ID > Driver > winme_xp folder containing the installed adjustment software. In Windows 2000, select the C:\FinePixS1000fd_USB_ID > Driver > win98_2k folder containing the installed adjustment software.

When the detection wizard window reappears, click "Next".

4-30

Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual When the install conrmation window appears, click [Continue Anyway].

4. Adjustments

When the install conrmation window appears, click [Continue Anyway].

4-31

4. Adjustments When the completion window appears, click "Finish".


Check that "Camera connect ok!!" is displayed in the software launched in , enter the serial number (8 digits) and then click "Start".

When the window shown below appears, click the "OK" button.

4-32

Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual When the window shown below appears, click the "Cancel" button.

4. Adjustments

The window shown below appears and the camera turns off. Click "Exit" and remove the xD-Picture card.

--> USB_ID Writing ends.

4-33

4. Adjustments4-17. Langeuage Setting



When the screen shown on the right appears, press the Right button.

4-34


4. Adjustments

Check the third number or letter from the left in the serial number and use the Down button to select the applicable model (Figure. 4-17-1). Then press the MENU/OK button. Model US-model EU/EG/EE-model CH-model 3rd digit in serial no. A~H,J,K Q~V W~Z Language Ship Area US Ship Area EX Ship Area CH

If "Set ** OK" appears on the screen, turn the camera off and remove the adjustment xD-Picture card. "**" shows the selected language. The screen shows the display that appears when "Ship Area US" is selected.

--> Langeuage Setting ends.

4-35

4. AdjustmentsMEMO


4-36


5. Inspection

5. Inspection5-1. Required Measuring EquipmentMeasuring equipment Power supply Digital voltmeter Ammeter xD-Picture card TV Monitor DC COUPLER CP-04 POWER CABLE JIG Macro Chart LCD Inspection Data Face Detection Test Chart SD CARD ULTRA2 1GB Remarks AC adapter (AC-5V), Regurated power supply For general use For general use (able to measure 1mA or less) For general use TV monitor, minimum resolution 600 lines Common with adjustment JIG Common with adjustment JIG Resolution conrmation For LCD inspection (downloaded from WEB.) Checking face detection operation To check SD card recording Parts number

CR0130900U9 ZJ00580-100 ZJ00525-100 ZJ00885-100 ZJ01021-100 ZPU0512-100

5-2.

Use DC COUPLER CP-04 and POWER CABLE JIG. The output current of the Regurated power supply must not become 2.5A or more. FinePix S1000fd

Connection of Measuring Equipment

DC COUPLER CP-04 Regurated Power supply

Digital voltmeter Ammeter

POWER CABLE JIG

5-1

5. Inspection5-3.Sequemnce 1 Item External visual check Mode


Inspection and Factory SettingsPreparations for adjustment Method of adjustment Measuring Measurement points (measurement points, subject, other) (VRs, waveforms, required values) equipment and jigs (VRs, positions) (1) Observe the camera. (1) Check for damage to the outer casing (Inventory repairs only). (2) Check for problems with the clicking or sliding movement of switches. (3) Check for dust or fogging in the Finder. (4) Check for dust or fogging in the LCD. (1) Plug the DC COUPLER CR0130900U9 CP-04 into the camera and connect the AC-5V. (2) xD card for recording (2) Insert a xD card. (3) Select the mode dial setting. (4) Set the power switch to ON. (5) If a message appears asking for the language and date to be set, press the specication button on the right. (6) Check the LCD screen display status. (7) Press the < EVF/LCD> button. (8) Check for blemishes in the CCD live image. checking. (3) Mode: AUTO (4) Check that the camera beeps. (5) < BACK>

2

Power switch check

Auto mode

LCD-ON

EVF-ON

3

Zoom operation check

Auto mode LCD-ON

4

Shock noise check Auto mode in Auto mode LCD-ON

(6) Check that the live image and text is displayed. (7) Check that the live image is displayed. (8) Monitor a very bright subject and check that the live image does not dim or darken. (1) Zoom drive noise. (1) Check that there is no abnormal noise. (2) LCD screen. (2) Check that there is no edge blurringCheck that the screen display accurately tracks zooming. (3) Zoom operation (T W). (3) Check that the zoom moves smoothly. (1) Apply a shock to the (1) Check for problems on the camera using the shock jig. LCD monitor. (2) Check that the camera recovers from synchronicity disruption. (Note) Do not apply shocks directly to the lens or card cover.

5-2

Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service ManualSequemnce 5 Item Resolution check Focusing check Mode

5. Inspection

6

Movie/audio recording check

7

Movie/audio playback check

8

Playback mode check

Preparations for adjustment Method of adjustment Measuring Measurement points (measurement points, subject, other) (VRs, waveforms, required values) equipment and jigs (VRs, positions) Auto mode (1) Use a macro resolution ZJ00525-100 LCD-ON chart as the subject. (2) Set the camera to Macro (2) Press the 4-way button mode. (left) and check that the Macro icon (tulip) appears on the LCD monitor. (3) Set the camera up so that the chart lls the screen from corner to corner. (4) Press the shutter button to (4) The indicator lamp take a picture. lightsgreen -> Intermittently lights orange or green (recording) -> Turns off. (1) Check that STANDBY Movie mode (1) Select the mode dial to Movie shooting mode. appears on the LCD monitor. LCD-ON (2) Press S1 -> S2 and then (2) Check that movie/audio release S2 -> S1. recording begins. Check that REC appears on the LCD monitor. (3) After 5 seconds, press and (3) Check that movie/audio then release S1. recording ends and that the data is recorded on the xD card. Playback (1) Set the camera to Playback mode. (2) Press the 4-way button (2) Check that the movie is (down) to play back the played back on the LCD movie. monitor. Check that the sound is played back through the speaker. Playback (1) Plug the AV cable into the (1) The LCD monitor image disappears and the indicator lamp lights green. (2) Check images shot at (2) Where the horizontal macro resolutions (manual resolution is as follows: photography). 350 TV lines or better at the center and 300 TV lines or better at the periphery (NTSC). 300 TV lines or better at the center and 250 TV lines or better at the periphery (PAL). (3) Disconnect the AV cable from the camera. Turn the camera off camera.

5-3

5. InspectionSequemnce 9 Item Playback mode check Mode Playback

Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service ManualPreparations for adjustment Method of adjustment Measuring Measurement points (measurement points, subject, other) (VRs, waveforms, required values) equipment and jigs (VRs, positions) (1) Start up in playback mode. (1) Press the button. (2) If a message prompting (2) the user to set the dateappears, press the buttonspecied on the right. (3) Check the playback image. (3) Check that the last imageshot appears, regardlessof whether it is automaticor manual.Check that the date is displayed in the YYYY.MM.DD forma. (1) Check that an erase (1) Select Erase -> Erase all from the menu and then press the OK button. message such as the following appears: Japan: OK? Overseas: ERASE ALL OK? China: OK? (2) Check that the recorded images are erased.

10

Erase mode check Erase

11

SD card recording check Flash operation check

Auto mode

(2) Select "OK" and press the OK button. (3) Turn the camera off. Disconnect the xD card from the camera. (1) Insert a SD card. (2) Select the mode dial setting. (3) Set the power switch to ON. (4) If a message appears asking for the language and date to be set, press the specication button on the right. (5) Press the ash pop-up button to open the ash. (6) Set the ash mode to Forced Flash.

(1) SD Card for recording checking. (2) Mode: AUTO

ZPU0512-100

(4)

(7) Focus on any subject and press the shutter button to take a picture.

(6) Press the 4-way button (right) and check that the Forced Flash icon appears on the LCD monitor. Press the ash lamp unit down approximately 1 cm and check that the Forced Flash icon appears when the lamp is gently released. (7) The indicator lamp lights green -> Intermittently lights orange or green (recording) -> Turns off.

5-4

Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service ManualSequemnce 12 Item Mode Preparations for adjustment (measurement points, subject, other) (1) Press the Intelligent Face Detection button. (2) Set up the camera facing the face detection chart at a distance of 30 to 40 cm. (3) Press the S1 button.

5. InspectionMethod of adjustment Measuring Measurement points (VRs, waveforms, required values) equipment and jigs (VRs, positions) (1) Set Face Detection to ZJ01021-100 ON. (2) Check that the Face Detection icon is displayed on the LCD monitor. (3) Check that the focusing target is aligned with a face that has the Face Detection icon. (4) Set Face Detection to OFF.

Checking face Auto mode detection operation LCD-ON

13

SD card playback check

Playback

14

Erase mode check Erase

(4) Press the face detection button. (1) Press the button. (2) Check the playback image. (2) Check that the photographed image is displayed. (1) Select Erase -> Erase all from the menu and then press the OK button. (2) Select "OK" and press the (2) Check that the recorded OK button. (3) Disconnect the SD card from the camera. Turn the camera off. (1) Insert the LCD monitor inspection card. (2) Start up the camera in Playback mode. (3) Play back a completely black image. images are erased.

15

LCD dust/defect check

Playback

ZJ00885-100 (2) Press the

button. (3) Check that there are no noticeable dust ecks or stains (bright spots, etc.) on the screen. (4) Play back a completely (4) Check that there are no white (75%) image. noticeable dust ecks or stains (smears, ashing points, etc.) on the screen. (5) Change the setting with the (5) Play the above 2 frames EVF/LCD button. and perform the same checks. (6) Set the power switch to OFF. (7) Disconnect the LCD monitor inspection card.

5-5

5. InspectionSequemnce 16 Item Battery low check Backup check Mode Auto mode

Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service ManualPreparations for adjustment (measurement points, subject, other) (1) Insert the xD-Picture card and set the DC COUPLER CP-04 and POWER CABLE JIG to the camera. (2) Set the power supply voltage. (3) Set the Mode dial to AUTO mode and turn the camera on. (4) Check that the pop-up ash opens and closes and check the backup. Method of adjustment Measuring Measurement points (VRs, waveforms, required values) equipment and jigs (VRs, positions) CR0130900U9 ZJ00580-100

(2) 5.00V 0.1 V (3) Check that the camera start up nomally. (4) Press the ash pop-up button to pop up the ash unit. Check that forced ash ring is displayed. Check that the ash mode reverts to AUTO when the 4-way key (right) is pressed after checking. (5) 4.86 V 0.05 V Check that the battery-low warning appears. (6) 4.40 V 0.05 V Check that the camera turns off.

LCD-ON

(5) Set the pre-end voltage.

(6) Set the end voltage.

17

Current Auto mode consumption check

LCD-ON

(1) Insert the xD-Picture card CR0130900U9 and set the DC COUPLER ZJ00580-100 CP-04 and POWER CABLE JIG to the camera. (2) Set the power supply (2) 5.00 V 0.05 V voltage. (3) Set the Mode dial to AUTO mode and turn the camera on. (4) After the LCD monitor live (4) 500 mA or less. image appears, check the (Stable state => When current consumption. the IRIS/FOCUS is not operating.) If the current consumption exceeds the above value, it is OK if the current drops into the standard range within 10 seconds. If the current is still outside the standard range after 10 seconds,the camera is faulty. (5) Set the power switch to OFF. (6) Disconnect the xD card

18

Checking standby current

Power off

from the camera. (1) Set the DC COUPLER CP-04 and POWER CABLE JIG to the camera. (2) Set the power supply (2) 5.00 V 0.05 V voltage. (3) Check the standby current (3) 0.5 mA or less when the power is turned OFF.

CR0130900U9 ZJ00580-100

5-6

Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service ManualSequemnce 19 Item Shipping inspection (Inventory repairs only) Mode

5. Inspection

Preparations for adjustment Method of adjustment Measuring Measurement points (measurement points, subject, other) (VRs, waveforms, required values) equipment and jigs (VRs, positions) (1) Mode dial. (1) AUTO mode (2) SETUP frame no. (2) New: The default SETUP frame No. setting is Continuous, but to clear the number of frames in the frame number memory to zero, you should always change the setting to New before turning the camera off. (3) Flash. (3) Pop down (4) Battery and cards not (4) Normal inserted. (5) Internal memory. (5) Check that the internal memory is formatted. * Excluding customers camera. (6) Battery cover. (6) Closed (7) Power off. (7) The power supply is stopped after the camera's shutdown sequence ends.

5-7

5. InspectionMEMO


5-8


6. Parts List

6. Parts List6-1.6-1-1.

Packing and AccessoriesUS-modelA107 A116 A117

*

or A122 A123 A124

*

A118A119 A120 A121

A126

A104A125

A108

A103

A105

A109 A110 A115 A106

A111

A113

A112 A102

* Partway through the production process, units were added for which the instruction manual was provided on a CDROM, and the items bundled were changed. Supply of the old parts (Ref.A118-A121) ends when becoming out of stock. After stocks run out, use combinations of the new parts (Ref. A122-125).

A101

A114

Ref No. A101 A102 A103 A104 A105 A106 A107 A108 A109 A110 A111 A112 A113 A114 A115

Parts No. CR013085199 CR013080599 CR013080499 CR074181499 CR013082099 CR013084499 CR013051299 FZ06957-200 CR0130999U9 CR013080699 CR013084899 CR013084999 FZ04792-100 CC013099899 CR173284999

Description UNITARY BOX PARTITION PAD B PARTITION PAD A INSTRUCTION PE BAG CAMERA WRAPPER BAG RATING LABEL US LENS COVER STRING CD ROM (SOFT WARE) LENS COVER SHOULDER BELT USB CABLE AV CABLE ALKALINE BATTERY DESTINATION LABEL US CAMERA OFFICIAL SEAL

Comment Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness Commonness

Ref No. A116 A117 A118 A119 A120 A121 A122 A123 A124 A125 A126

Parts No. CR013085999 CR013081499 CR013081899 CR013081299 CR013081399 CR013080999 CR013088399 CR013088499 CR013088599 FZ07269-101 CC013099699

Description CARD (US) WARRANTY U SAFETY INSTRUCTION BASIC MANUAL E BASIC MANUAL S MANUAL E BASIC MANUAL ENGLISH BASIC MANUAL FRENCH BASIC MANUAL SPANISH CD ROM(SEVEN LANGUAGE MANUAL) LEAFLET

Comment Commonness Commonness Old Old Old Old New New New New Commonness

6-1

6. Parts List6-1-2. EU-model


A104 A107

A103 A108 A105

A109 A110 A115

A106

A111

A113

A112 A102

A101

A114



Description UNITARY BOX PARTITION PAD B PARTITION PAD A INSTRUCTION PE BAG CAMERA WRAPPER BAG RATING LABEL WEEE LENS COVER STRING CD ROM (SOFT WARE) LENS COVER SHOULDER BELT USB CABLE AV CABLE ALKALINE BATTERY DESTINATION LABEL CAMERA OFFICIAL SEAL

Comment

Ref No. Parts No.

Description

Comment

6-2

Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual6-1-3. E1-modelA107 A104

6. Parts List

A116 A117 A118

A103 A119 A108 A106 A115 A105

A109 A110

A111

A113

A112 A102

A101

A114




Comment

Ref No. A116 A117 A118 A119

Parts No. CR013088499 CR013088699 CR013088799 FZ07269-101

Description Comment BASIC MANUAL FRENCH BASIC MANUAL GERMAN BASIC MANUAL DUTCH CD ROM(SEVEN LANGUAGE MANUAL)

6-3

6. Parts List6-1-4. EG-modelA107 A116


* A117 A118 A119

or

* A120

A122

A121

A104

A103A108

A105

A109 A110 A115

A106

A111

A113

A112 A102


A101

A114





Ref No. A116 A117 A118 A119 A120 A121 A122

Parts No. CR173281399 CR013081899 CR013081299 CR013080999 CR013088399 FZ07269-101 CC013099699

Description WARRANTY EG SAFETY INSTRUCTION BASIC MANUAL E MANUAL E BASIC MANUAL ENGLISH

Comment Commonness Old Old Old New

CD ROM(SEVEN LANGUAGE MANUAL) New LEAFLET Commonness

6-4

Condential: FUJIFILM Service Center Use Only FinePix S1000fd Service Manual6-1-5. EE-modelA107

6. Parts List

*A116 A117 A118

or

*

A121

A119

A104A120

A103A108

A105

A109 A110 A115

A106

A111

A113

A112 A102


A101

A114



escription UNITARY BOX PARTITION PAD B PARTITION PAD A INSTRUCTION PE BAG CAMERA WRAPPER BAG RATING LABEL WEEE LENS COVER STRING CD ROM (SOFT WARE) LENS COVER SHOULDER BELT USB CABLE AV CABLE ALKALINE BATTERY DESTINATION LABEL CAMERA OFFICIAL SEAL


Ref No. A116 A117 A118 A119 A120 A121

Parts No. CR013081899 CR013081299 CR013080999 CR013088399 FZ07269-101 CC013099699

escription SAFETY INSTRUCTION BASIC MANUAL E MANUAL E BASIC MANUAL ENGLISH CD ROM(SEVEN LANGUAGE MANUAL) LEAFLET

Comment Old Old Old New New Commonness

6-5

6. Parts List6-1-6. CH-modelA107 A115 A119 A116


A120

A104

A103 A108 A117 A106 A105

A109 A110

A111

A113

A112 A102

A118

A101

A114



Description UNITARY BOX C PARTITION PAD B PARTITION PAD A INSTRUCTION PE BAG CAMERA WRAPPER BAG RATING LABEL CH LENS COVER STRING CD ROM (SOFT WARE) LENS COVER SHOULDER BELT USB CABLE AV CABLE ALKALINE BATTERY DESTINATION LABEL WARRANTY CH

Comment

Ref No. A116 A117 A118 A119 A120

Parts No. CR013081099 CR173283999 CC173299799 CR013087999 CC013099699

Description MANUAL C CERTIFICATE REGULATION SEAL SAFETY INSTRUCTION CH LEAFLET

Comment

6-6


6. Parts List

6-2.

FRONT COVER CONSTM201 M207 M209

M210

M202 M206

M208

M204

N.S. M203

M205

M209

N.S.=Not SupplyRef No. M201 M202 M203 M204 M205 M206 M207 M208 M209 M210 Parts No. CR0130100U9 CR0130996U9 CR013010599 CR013010199 CR173210699 CR013010499 CR013010299 CR511154299 CR013040899 CR511154599 Description FRONT COVER CONST LENS RING UNIT DUST PROOF SPONGE FRONT COVER ISOLATION PIECE BATTERY SPRING HAND GRIP SCREW M1.4XL2 SCREW M1.7XL2.0 SCREW M1.7XL3.5 Comment Ref No. Parts No. Description Comment

6-7

6. Parts List6-3. BATTERY COVER CONST


M301

M310

M309

M308

M306 M305 M304 M303 M307 M302

Ref No. M301 M302 M303 M304 M305 M306 M307 M308 M309 M310

Parts No. CR0130200U9 CR013020199 CR013020299 CR013020599 CR013020499 CR013020899 CR013020399 CR013020699 CR013020799 CR013040599

Description Comment BATTERY COVER CONST BATTERY COVER BATTERY LATCH BATTERY COVER SPRING BACK BATTERY COVER SPRING FRONT BATTERY COVER SPONGE BATTERY LATCH SPRING BATTERY SHEET METAL 1 BATTERY SHEET METAL 2 SCREW M1.4X2.0

Ref No. Parts No.

Description

Comment

6-8


6. Parts List6-4.M435 M436 M434 N.S. M430 M440 M429 M428 M427 M425 M433 M423 M416 M441 M441 M417 M406 M405 M402 M411 M419 M418 M437 M422 M421 M424 M438 M431Ref No. M401 M402 M403 M404 M405 M406 M407 M408 M409 M410 M411 M412 M413 M414 M415 M416 M417 M418 M419 M420 M421 M422 M423 M424 M425 M426 M427 M428 M429 M430 M431 M432 M433 M434 M435 M436 M437 M438 M439 M440 M441 M442 M443 Parts No. CR013019199 ESP3002169 CR511120699 EMI3003069 CR074169099 CR013012199 CR013012299 ECA0197019 CR013031299 CR0130302U9 CR013050299 CR511156099 EWI5111129 EWI5111139 CR013019499 CR0130309U9 CR0130400U9 CR0130301U9 CR013050199 CR013012699 CR013012599 CR013012099 FZ07059-100 CR0130110U9 CR0130997U9 CR013011999 CR013011499 CR013011399 CR013011299 CR013011599 CR013011799 CR013011199 CR013012499 CR013011699 CR013040199 CR511154599 CR511154399 CR013040999 CR511154799 CR013040299 CR511154499 CR013040699 CR511154299

MECHANICAL BLOCKDescription MAIN FRAME SPEAKER TRIPOD MIC XD CARD LABEL STRAP LEFT STRAP RIGHT CAP. CAP. MYLAR B BATTERY PWB ASSY BATTERY SEAL CAP. MYLAR A AF WIRE RED AF WIRE BLACK LED SILICONE AF LED PWB ASSY LENS CONST MAIN PWB ASSY LENS FPC SPONGE TAPE GASKET LCD HOLDER MYLAR LCD HOLDER LCD BACK COVER CONST KEY FPC UNIT LCD SPONGE OK BUTTON 4 WAY BUTTON 2 BUTTON 3 BUTTON USB COVER BACK COVER KEY SHEET METAL MYLAR FAKE BATTERY COVER SCREW M1.7XL4.5 SCREW M1.7XL3.5 SCREW M1.4XL3 SCREW M1.7XL3.5 SCREW M1.7XL2.5 SCREW M1.7XL3.0 SCREW M1.7XL4.5 SCREW M1.7XL3.5 SCREW M1.4XL2 Comment

M437

M437 M411

M412 M411 M410 M409 M408 M407 M435 M415 M437 M441 M437 M420

M412 M436 M443

N.S.

M432 M439

M436

M426

M414 M413 M437

M436

M401 M404

M440

M403 M442

M436 M439

N.S.=Not Supply

6-9

6. Parts List6-5. TOP COVER CONSTM501


M517 M513

Ref No. M501 M501 M502 M503 M504 M505 M506 M507 M508 M509 M510 M511 M512 M513 M514 M515 M516 M517 M518 M518 M519 M520 M521 M522 M523 M524 M524 M525 M526 M527 M528 M528A M529 M530 M531 M532 M533 M534 M535 M536 M537 M538 M539 M540 M541 M542 M543 M544 M545 M546 M547 M548

Parts No. CR0130130U9 N.S. CR013018899 CR0130300U9 CR013018399 CR013018499 CR013015599 CR013013899 CR013013699 CR511156399 ELC6001009 CR013016299 CR013016199 CR013015399 CR511155899 CR013015199 CR511150999 CR013017599 CR0130170U9 CR0130196U9 CR0130308U9 CR013017399 CR0130303U9 CR013017699 CR0130171U9 CR013017299 CR013019699 CR013017499 CR013017799 CR013019799 CR013017899 CR013013199 CR013019599 CR013018599 CR013018999 CR013019099 CR013013999 CR013014099 CR013015299 CR013015499 CR511153699 CR013018199 CR511153399 CR511154899 CR013050499 CR0130304U9 CR0130307U9 CR013018299 CR511154299 CR511154399 CR511154599 CR013040499 CR511154199

Description TOP COVER CONST TOP COVER CONST TOP COVER MYLAR TOP FPC UNIT TOP COVER BUTTON STATUS LED POWER KNOB WT BUTTON SHUTTER BUTTON SHUTTER SPRING EVF EYE RING EYE CUP MODE DIAL COVER MODE DIAL STICKER MODE DIAL CAP MODE DIAL SPRING FLASH TOP COVER FLASH BOTTOM ASSY FLASH BOTTOM ASSY FLASH WIRE UNIT FLASH FIX FLASH DETECT PWB ASSY FLASH ADHESIVE FLASH UNIT FLASH BOTTOM COVER FLASH BOTTOM COVER FLASH HINGE FLASH SPRING FLASH SPRING FLASH SPONGE TOP COVER TOP COVER FUJI LOGO AF LENS AF LENS ADHESIVE WT SPRING WT SLIDER MODE DIAL STOPPER MODE DIAL SWITCH COVER FLASH LOCK FLASH LOCK PLATE FLASH LOCK SPRING FLASH LOCK PUSHER FLASH DETECT WIRE MYLAR FLASH BOARD FLASH DETECT WIRE UNIT FLASH BUTTON SCREW M1.4XL2 SCREW M1.4XL3 SCREW M1.7XL3.5 SCREW M2.0XL5.0 SCREW M1.4XL2

Comment

M519 M545

M514 M515 M521 M522 M526

M520 M518 M523 M525

M512

M516

M525

M511 M524

M544

M545 M510 M546

M506 M507 M508M509

M527

M528AM529 M540 M531

M528

M526

M505 M544 M548 M533 N.S.

M532

M534 M535 M545

M530 M536 M537 M543 M544 M547

M541 M542 M545

M504 M503

N.S. N.S. N.S. M538 M539 M548

M544

M502

N.S.=Not Supply

Revised: 03, Dec. 2008

6-10


6. Parts List

6-6.[NOTE]

Electrical parts* Due to standardization, replacement in the parts list may be different from the parts list specied in the circuit or the components used on the set.

The components indicated by mark are critical for safety. When indicated parts by reference number, please include the board name.Ref No. Parts No. Description Comment PWB diagram

BATTERY PWB ASSY[FUSE] F1 EFU3001059 FUSE F-2

[CONNECTOR] J1 ECN3071819

JACK

KEY FPC UNIT[SWITCH] SW1 ESW4022009 SW2 ESW4022009 SW3 ESW4022009 SW4 ESW4022009 SW5 ESW4022009 SW6 SW7 SW8 SW9 SW10 ESW4022009 ESW4022009 ESW4022009 ESW4022009 ESW4022009 SWITCH SWITCH SWITCH SWITCH SWITCH SWITCH SWITCH SWITCH SWITCH SWITCH

MAIN PWB ASSY[BATTERY] GC200 ECA2009049 [CONNECTOR] CON301 ECN3071029 CON302 ECN3071029 CON304 ECN4225009 CON305 ECN3071809 CON306 ECN4296049 CON600 ECN1921059 J100 FGY107-0201 J500 ECN4296029 [JACK] J300 BACKUP BATTERY

CONNECTOR CONNECTOR CONNECTOR CONNECTOR CONNECTOR CONNECTOR CONNECTOR CONNECTOR

ECN3071589

JACK

[SWITCH] SW100 ESW3017009

DETECTOR SWITCH

FLASH BOARD[SWITCH] ESW3017009 SWA1 DETECTOR SWITCH

6-11

6. Parts ListMEMO


6-12


7. Appendix

7. Appendix7-1.To ensure that after-sales srevice is performed accuratety, keep a record here of the technical updates issued that cover this device.

List of Related Technical Updates IssuedDate 03, Dec. 2008 Title Preventive measure for "Flash pop-up failure" and Service Manual revisions

Technical Update No. 2008-144

Details/Other Revised pages: P6-10

7-1

Midtown West, 7-3, Akasaka 9-chome, Minato-ku, Tokyo 107-0052, Japan

Date post:	30-Oct-2014
Category:	Documents
Author:	anon523999402
View:	231 times
Download:	10 times

Finepix S1000 Service Manual

Documents

intermittently lights orange

removable disk recognized

main pwb assy

main pwb initialize

fujifilm service center

dc coupler cp

face detection icon

battery pwb assy

Fuji Finepix 602

Finepix s4200-s4500

DN-S1000 - Gothic Maine

Multi-Tech S1000 / S1000-Ultra Air Purifier...Multi-Tech S1000 / S1000-Ultra Air Purifier Instruction Manual (Please read before using air purifier) Surround Air Division Indoor Purification

Fujifilm FinePix HS10

FINEPIX S9900W Series FINEPIX S9800 Series First Steps ... · Wireless Networks DIGITAL CAMERA FINEPIX S9900W Series FINEPIX S9800 Series FINEPIX S9700 Series Owner’s Manual Thank

FUJIFILM FINEPIX JX680

FinePix E550 Manual -

Siemens Acuson S1000 Brochure

IZT S1000 / IZT S1010 Options Version 1 · IZT S1000-410 DRM30/DRM+ Modulator 0 1 IZT S1000-410a DRM30/DRM+ Modulator for MDI Input 0 1 IZT S1000-410b DRM30/DRM+ Modulator Bundle

Adobe Photoshop Camera Raw 4.6 Read Me · PowerShot Pro1 Contax N Digital Epson R-D1 R-D1s Fujifilm FinePix E900 FinePix F700 FinePix IS-1 FinePix IS Pro FinePix S100FS Nikon D1 D1H

FinePix S5200/FinePix S5600 Manual - FujifilmProduct Name: FUJIFILM DIGITAL CAMERA FinePix S5200 / FinePix S5600 Manufacture’s Name: Fuji Photo Film Co., Ltd. Manufacture’s Address:

FINEPIX XP170 FINEPIX XP150/XP160 FINEPIX XP100 - Fujifilm

PDF FinePix A400 / FinePix A500 Manual – Home - Fujifilm · OWNER’S MANUAL This manual will show you how to use your FUJIFILM DIGITAL CAMERA FinePix A400 / FinePix A500 correctly.

FINEPIX X100

Finepix s5500 Manual

finepix A610_A800OwnersManual

FINEPIX S9400W Series FINEPIX S9200 Series First Steps ...