adalet offers a range of fittings and accessories for use in general purpose or industrial locations. these
fittings and accessories are used in conjunction with our industrial electrical enclosures.
Jag FITTInGsused in wet or dry locations, adalet Jag fittings provide a complete solution for terminating metal clad cables
in general or industrial locations. Constructed from copper-free aluminum alloys, the adalet Jag fittings is a
single connector which allows for easy, slip-on installation with no disassembly required. adalet offers a wide
range of sizes to provide the most precise fit with a water-tight seal
COnDUit Ventilating Cable SuPPortS & VentilatorStemperature extremes, along with rodents, can cause costly damage to conduit and cabling – resulting in
losses in the millions of dollars, thousands of hours of downtime and countless interruptions in daily life and
commerce nationwide. adalet’s line of conduit ventilating cable supports and conduit ventilators are simple,
low-cost devices that improve the service life and load-carrying capacity of cable within conduit risers. easy to
install, they protect the cable from rodents and their razor-sharp teeth while allowing ample circulation to cool
the conduit.
SKY-tie™ buS-DroP Cable ClaMPSSimple, effective, and incredibly easy-to0install, the adalet Sky-tie™ quarter bend cable clamp is the perfect
solution to eliminate electrical and trip hazards from your shop floor. the Sky-tie™ is used as both a support
and as an anchor in installations where bus-drop cables transmits power from bus-duct to machine tools and is
also ideal for suspending portable tools, air lines, and water lines.
• Slip-on design with no disassembly for easy installation • Neoprene bushing for raintight seal • Locknuts, bushings and flange gasket included – no additional materials to purchase • Flange gasket prevents moisture penetration through threads • Fits broad range – .351-4.62 cable O.D. • Determine satisfactory fit by checking cable dimensions A and B. If cable dimensions do not fall within acceptable range, consult factory.
DIA. OVER JACKET MAX CABLE CONDUIT FITTING LENGTH SHIP DRILL A CORE DIA. SIZE O.D. OVERALL WEIGHT CLEARANCE CAT. NUMBER MIN. MAX. b C D E (lbs.) HOLE DIA.
CONDUIT MAX CABLE O.D. SHIP SIZE b WEIGHT CAT. NUMBER A ONE HOLE THREE HOLE* C D (lbs.)
CV20 2 1.60 .74 4 11/16 2 5/8 2 1/2
CV25 2 1/2 1.91 .93 5 5/32 2 5/8 2 1/2
CV30 3 2.37 1.19 5 13/16 2 3/4 3
CV35 3 1/2 2.75 1.41 6 3/16 2 3/4 3 1/2
CV40 4 3.12 1.63 6 13/16 2 7/8 4
CV50 5 3.82 2.13 8 1/8 3 3/8 5
CV60 6 4.42 2.55 9 5/8 3 3/4 6
TO OrDEr: 1. Select catalog number of fitting 2. Indicate number and diameter of cables 3. Where used with interlocked armored cable, specify whether gasket to fit over jacket or over armor
* Additional holes can be supplied-consult factory
• Helps reduce temperatures in conduit, improving service life and load carrying capacity of the cable• Neoprene gasket provides watertight seal and cable support• Set screws secure the ventilator to conduit• For supporting and sealing cable risers and allowing escape of heated air from conduit • Type CV Supports are designed for use at top of conduit where cable extends into air
• Used in conduit system to allow air to enter conduit riser• Castings are aluminum, anodized and Teflon sealed for maximum corrosion resistance• Helps reduce temperature in conduit riser, improving service life and load carrying capacity of the cable
• Used where existing XLP or EPR cables are installed in conduit• Split to permit installation after cable has been pulled or where cable extends some distance from ventilator mounting• Neoprene gasket provides watertight seal. Gasket slit to allow installation.
TO OrDEr: 1. Select catalog number of fitting 2. Indicate number and diameter of cables 3. Where used with interlocked armored cable, specify whether gasket to fit over jacket or over armor
* Additional hole can be supplied-consult factory
VentilatORS
STANDARD FEATURES
CONDUIT MAX CABLE O.D. SHIP SIZE b WEIGHT CAT. NUMBER A ONE HOLE THREE HOLE* C D (lbs.)
Keyhole slots permit assembly on cable without removalof bolts or threading of cable through fitting.
SHSHD
SHS
Lugs prevent nuts from turning.
Bus-Drop Cable Clamps - Sky-Tie™
MAX. CARTON STD. PKG CAT. NUMBER SPRING LOAD QTY. WEIGHT QTY. WEIGHT
SHS-50 60 lbs. 10 2.2 50 11
SHS-75 70 lbs. 10 2.7 50 14
SHS-1125 160 lbs. 10 11 10 11
lbs.lbs.
• Supports cable up to 1-1/8" diameter. Uniform “lap” design of each clamp-half results in support along the entire quarter bend.
• Anchors cable for 90° angle transitions using a simple, two- piece construction of interchangeable clamp-halves.
• Loops excess cable for convenient handling and out-of-the-way storage, via the Sky-Tie™ SHD Duplex Converter. The SHD reduces the need to cut cable when machines are moved to new locations. The SHD converter simply fits between the two halves of the Sky-Tie™ SH cable clamps.
• Uses: Machine Tools, Portable Tools, Air Lines, Other heavy-cable support applications.
• Sky-Tie™ Springs Heavy-duty Sky-Tie™ Springs insure tautness of the cable, while absorbing vibrations and shocks. Each spring slips into the Sky-Tie™ clamp at its outside bend (or, if using the SHD Duplex, the converter’s outside bend), and ties back to a structural member. Three spring models with maximum load capacities of 60, 70 and 160 pounds.
