FL-2000 Manual

Copyright © 2010 Shenzhen C2S Technology Co., Ltd. All rights reserved.

Fleet Vehicle GSM/GPRS/GPS Tracker FL-2000G User’s Manual


Table of Content

1. Statement ............................................................................................................................................ 3 2. Product Introduction: .......................................................................................................................... 3

2.1 Brief Description ........................................................................................................................ 3 2.2 Applications ................................................................................................................................ 3

2.2.1 Application Diagram ................................................................................................... 3 2.2.2 Application Range........................................................................................................ 3

2.3 Features ........................................................................................................................................ 4 2.4 Specification ............................................................................................................................... 4

3. Hardware Knowledge ......................................................................................................................... 5 3.1 Model and Standard package Kits...................................................................................... 5 3.2 Mainframe ................................................................................................................................... 6

3.2.1 Mainframe Sockets: ..................................................................................................... 6 3.2.2 LED Indications: ............................................................................................................ 6

4. Installations: ........................................................................................................................................... 6 4.1 Insert Simcard ............................................................................................................................ 6 4.2 Install Power and I/O Cable .................................................................................................. 7

4.2.1 Power/GND .................................................................................................................... 7 4.2.2 Digital Inputs/Outputs ............................................................................................... 8 4.2.3 Analog Inputs ................................................................................................................ 9

4.3 Install Fuel Level Sensor ....................................................................................................... 10 4.4 Install Dispatch Navigator Display (RS232 Interface) ................................................ 10 4.5 Install LED ADS display (RS232) ......................................................................................... 10 4.6 Install GSM/GPS antenna ..................................................................................................... 10

4.6.1 Install GSM antenna .................................................................................................. 10 4.6.2 Install GPS antenna .................................................................................................... 10

4.7 Install Microphone and Speaker ....................................................................................... 11 5. Unit Configuration ............................................................................................................................. 11

5.1 Configuration Knowledge .................................................................................................... 11 5.2 Configure Device by PC Virtual Handset Software ..................................................... 12

5.2.1 Connect FL-2000G to PC Serial Port: ................................................................... 12 5.2.2 Setup Parameter by VHandset.ext tool. ............................................................. 13

5.3 Configure Device by Navigator Display .......................................................................... 13


1. STATEMENT

Thanks for your selection of FL-2000 series Fleets vehicle tracking Terminal from C2STEK Please read this user’s guide carefully and make sure you will use the original accessories provided by C2STEK in avoid of any unexpected damage for this product.

Please kindly be attention that this user guide may be changed at any time without prior notification.

In no event shall C2STEK be liable for direct, indirect, special, incidental, or consequential damages (including but not limited to economic loss, personal injury, and loss of asset and property) arising out of the use or inability or illegality to use the product or documentation.

2. PRODUCT INTRODUCTION:

2.1 BRIEF DESCRIPTION

FL-2000 series AVL devices are well-defined GPS/GPRS/SMS tracking device for fleet management Application. It featured with small size, easy installation and satisfies most features expectations from solution integrators. It equipped with 50Channel Industrial High sensitivity GPS module and State-of-art GSM/GPRS module, harsh-weather and shock resistant PCB design. It has outstanding multiple inputs and outputs: Door Lock/Unlock, Cut Relay, taxi Odometer , fuels level sensor, One-Key call help, Navigator Dispatch display integrated functions for optional.

FL-2000 series devices are designed as universal application for any vehicles with power system 9-36V DC.

2.2 APPLICATIONS

2.2.1 APPLICATION DIAGRAM

2.2.2 APPLICATION RANGE


Vehicle Real Time Tracking Car Security/Anti-Hijack Fleet Management

2.3 FEATURES

Ublox LEA_5x series GPS and Quad Band GSM 850/900/1800/1900Mhz Track by SMS/GPRS （C2STEK Protocol） Lock/Unlock door (Optional) Track on Demand Track by Time Interval Track on Mobile Phone Listen-in or Two-way Audio (Optional) Internal Flash Memory (4M) store more than 40000way points for GSM Null zone Internal Backup Battery SOS Alarm Working Time limit and alarm ACC ON/Off report Geo-fence Alarm Engine Idle behavior alert Speeding Alarm Tow Alarm External Power temper Alarm Mileage Report Engine Cut (Engine immobilization) Camera (optional) Fuel Level Sensor (Optional) RFID Reader (optional) LED Advertisement Display (optional) Dispatch Navigator Display (optional)

2.4 SPECIFICATION Data Communication

GPRS Modem Huawei EM310/ Huawei MG323

GSM Frequency 900MHz/1800MHz, or 850/900/1800/1900MHz

GPRS Data GPRS Class 10

Coding Schemes CS1-CS4

SMS Point-to-Point mobile originated & mobile terminated

Cell Broadcast

RF Power EGSM900 Class4(2W)

GSM1800 Class1(1W)

Antenna Connection SMA

Sensitivity <-106dBm


Navigation

GPS Receiver 50Channels Ublox NEO-5Q

Frequency L1 1.57442Ghz

Acquisition

Time TTFF

Cold Start 29S

Hot Start <1S

Accuracy 2.5-5 Meters (50% probable)

10 Meters (95% probable)

Sensitivity

Tracking -160dBm

Reacquisition -160dBm

Cold Start -143dBm

Antenna Passive patch Antenna with SMA

connection

Physical

Outside Casing Size 101.3MMx74.8MMx29.5MM

Weight(Mainframe Only) 0.3Kg

Casing Materia Aluminum

Electrical

Power Supply 9-36V DC

Internal Battery 500mAh-1600mAh(optional)

Working Temperature -20℃-75℃

Average tracking power (GPS

full power, GPRS connected)

175 mW tracking: GPS always on, gprs active, gprs session open.

Approx. 9 W peak during data transmission.

3. HARDWARE KNOWLEDGE

3.1 MODEL AND STANDARD PACKAGE KITS 1) Tracker Unit 2) Microphone 3) Engine cut relay 4) GPS Antenna 5) GSM Antenna 6) 20Pin Harness 7) SOS button


8) Dispatch Navigator Display 9) Camera 10) Fuel Level Sensor 11) LED Ads Board

3.2 MAINFRAME 3.2.1 MAINFRAME SOCKETS:

3.2.2 LED INDICATIONS: After the Power ON, please check with the diagnostic LED the correct behavior of the GPS tracker following these Specifications:

4. INSTALLATIONS:

4.1 INSERT SIMCARD


1) Using screwdriver to SIM card Slot spring up button 2) Slide out the drawer 3) Put the SIM card to the drawer 4) Slid back the drawer with SIM card to slot. Note: - FL-2000 tracker is using only in GSM network. - The SIM card should be enabled with GPRS service, and with no Pin code for access. - The SIM card should be with Incoming call Number Show function enabled - If you want to track by SMS, then the SIM card should be SMS service enabled too. 4.2 INSTALL POWER AND I/O CABLE 4.2.1 POWER/GND 1) Plug the 20-Pins Molex Connector into the back of the device, using the outlet marked as L2 2) The GPS tracker has a fuse holder already connected to the power cable provided. Just connect the Red/White and Black/White Wires to the Vehicle's Power supply of 12V or 24V. Please connect: - The red/white wire to the positive (+) pole - The black/white wire to the Negative (-) pole

Note: The power source must be permanent. The GPS device must be powered even when the vehicle's engine is turned off. This is not dangerous for the vehicle's security, given the device's very low absorption. The GPS tracker has an internal backup battery that, if


connected to NON PERMANENT power supply (example: cigarette lighter), would be damaged in a few months.

4.2.2 DIGITAL INPUTS/OUTPUTS

Item Pin No. Wire Color Function/Specification Description

Digital

Output

Pin16/L2 Grey/White Immobilizer relay control for ignition

Pin6/L1 Black/White Door Unlock, Negative Trigger

Pin7/L1 Green/White Door Lock, Positive Trigger

Dig

ital

Inp

ut

Pin3/L2 Red/White Panic Button, Negative Trigger

Pin6/L2 Orange/White Siren Check, Positive Trigger

Pin7/L2 Brown/White Duty/Empty Check, Positive Trigger

Pin8/L2 Blue/White Call Center, Negative Trigger

Pin18/L2 Yellow/White Ignition (ACC) Check, Positive Trigger

Pin1/L1 N/A Not Defined, Positive Trigger

Pin3/L1 N/A Not Defined, Negative Trigger

Pin4/L1 N/A Negative Trigger

Pin5/L1 N/A Positive Trigger - Ignition Detect To obtain the maximum level of movements notification, to control and report the ENGINE USAGE HOURS, use the Speaking system properly and Fuel consumption reports, it's strongly recommended to connect the tracker to the ignition key, within the yellow/White(Pin18) wire available out of the Molex Connector. You should connect this yellow/White wire to a power source that's equal or greater to 8 Volts with engine started, less than 1.5 Volts with engine stopped.


- Immobilizer Relay Control:

- Install SOS Panic Button and Usage

The provided Panic button is a lock/Unlock type button.

4.2.3 ANALOG INPUTS


Pin No. Wire Color Function/Specification Description

Pin17/L2 Green/White Fuel Sensor Application

Pin2/L1 N/A Temperature Sensor Application

4.3 INSTALL FUEL LEVEL SENSOR Please refer to FL-2000F Fuel Level Sensor Documents

4.4 INSTALL DISPATCH NAVIGATOR DISPLAY (RS232 INTERFACE) Please refer to FL-2000N Navigator Screen Wiring Diagram

4.5 INSTALL LED ADS DISPLAY (RS232) Please refer to FL-2000L LED Ads Board Documents

4.6 INSTALL GSM/GPS ANTENNA

4.6.1 INSTALL GSM ANTENNA The GSM antenna should be installed in an optimum location, to intercept the cellular signals, arriving at slightly above zero degrees from the horizon. Signals will typically penetrate through nonmetal material such as glass, fiberglass, and aluminum. Please refer to the illustrations below:

4.6.2 INSTALL GPS ANTENNA To ensure best reception, install the GPS antenna in a location that provides a clear sky view (Greater than a 90 degree angle view of the sky. Please refer to the following illustration:


4.7 INSTALL MICROPHONE AND SPEAKER Please follow below diagram to install the Microphone and Speaker. It will enable the two way audio conversation by hands freely.

5. UNIT CONFIGURATION

5.1 CONFIGURATION KNOWLEDGE 5.1.1 What’s necessary parameter to enable device working?


- Device ID

This device ID could be any number with you wants, and you need to register this ID number into the server database by Data Manager. It’s the only recognition code can be identified by the Server. Normally we use the Device SIM No. as the device recognition code.

- IP/Port It's for your Server GPRS gateway IP addressed and Port no, which you used for listen vehicle units incoming data in TCP/IP communication

- APN: APN is GPRS Access Point Name from your GSM Network Provider. You should get this name from your GSM Service Provider.

- Server SMS Service NO.: It’s Server SMS service NO. Which use as to receiving SMS data from mobile device. You can treat it as a mobile phone attached to a computer COM port for SMS receiving and sending.

5.2 CONFIGURE DEVICE BY PC VIRTUAL HANDSET SOFTWARE

5.2.1 CONNECT FL-2000G TO PC SERIAL PORT:

Pin No. Wire Color Function/Specification Description

Pin4/L2 Yellow/White RXD, Receive Data

Pin14/L2 Red/White TXD, Transmit Data

Pin15/L2 Black/White GND, Ground If your PC doesn’t have a Serial Interface, you need get one Serial-USB Convert Cable. See as following:


5.2.2 SETUP PARAMETER BY VHANDSET.EXT TOOL. Details please refer to our VHanset.exe tool manual.

5.3 CONFIGURE DEVICE BY NAVIGATOR DISPLAY Please refer to PND-100 Manual.

Date post:	16-Apr-2015
Category:	Documents
Upload:	olesya-borodykhina
View:	88 times
Download:	3 times