+ All Categories
Home > Documents > Flame Eye FE2020 - Credfeld Ltd

Flame Eye FE2020 - Credfeld Ltd

Date post: 17-Feb-2022
Category:
Upload: others
View: 0 times
Download: 0 times
Share this document with a friend
1
For Supervision of all types of Flames in Industrial Multi-Burner Boilers, Process Fired Heaters and Incinerators Flame Eye FE2020 Advanced Flame Monitoring System T +44 (0)23 8045 4359 F +44 (0)23 8045 4399 E [email protected] W www.credfeld.uk.com Reg. Office. 13 HYS, Port Hamble, Satchell Lane, Hamble, Southampton SO31 4QD. UK Features Excellent discrimination between adjacent or opposite burner Fully fail-safe self-checking design Easy to use and set up Continuous readout of flame and threshold levels Electronic head testing – no mechanical shutter Based on infra-red (IR) detectors sensing the high frequency flicker in the flame Low power consumption (10 Watt) 4 Selectable high pass filter characteristics for improved discrimination Constant flame signal over wide turndown range due to use of high frequency flicker flame Easily adjustable gain and threshold Easy access to viewing head lens for cleaning Quick disconnect plug at viewing head Available in 115VAC / 230VAC / 24VDC SIL 2 Certificate of testing D009_SV001 Rev2 to EIC 61508 CE Approval General Description The Flame Eye Flame monitoring system consists of a viewing head, which is mounted on the burner front and powered by remote signal processor unit. The signal processor unit is housed in an IP65 enclosure and consists of signal processing circuitry, display drive, Flame “On/Off” relays, Fault relay and 4–20mA analogue output for remote Flame indicator. How It Works The viewing head uses a solid-state photo detector that responds to the high frequency flicker in the flame. This fluctuating signal is then converted to balance signal lines for transmission to the signal processor unit. The use of balanced signal lines enables a high rejection of electrical interference to be achieved. Specifications Electric Power Input AC Model – 115/230 VAC +10%–20%, 50/60Hz, 12VA DC Model – 24 VDC +10%–10%, 10 Watt Optical Silicon Viewing Head (Type FM2020SI) Spectral Response – 300nm to 1100nm Environmental Ambient Temp. Control Unit 0°C–70°C Viewing Head (FM2020SI) 0°C–125°C Case Temp. Viewing Head Housing 0°C–85°C Cable (between Viewing Head & Control Unit) 2 twisted pair overall braided screen Outputs from Control Unit Flame on Relay – 1 Changeover contacts rate at 2A @ 230VAC Fault Relay – 1 Changeover contacts rate 2A @ 230VAC Analogue Flame Signal – 4–20mA for remote signals Time Delay Settings Flame on delay time fixed at 1 second Flame off delay time fixed at 2 seconds Flame Filter Characteristics Channel 1 18Hz Channel 2 36Hz Channel 3 72Hz Channel 4 144Hz Self-Check Time Periodic self check every 5 seconds Error Code E1 Internal fault E2 Flame on delay driver fault E3 Electronic shutter fault
Transcript

For Supervision of all types of Flames in Industrial Multi-Burner Boilers, Process Fired Heaters and Incinerators

Flame Eye FE2020Advanced Flame Monitoring System

T +44 (0)23 8045 4359 F +44 (0)23 8045 4399 E [email protected] W www.credfeld.uk.com Reg. Office. 13 HYS, Port Hamble, Satchell Lane, Hamble, Southampton SO31 4QD. UK

Features

• Excellent discrimination between adjacent or opposite burner

• Fully fail-safe self-checking design

• Easy to use and set up

• Continuous readout of flame and threshold levels

• Electronic head testing – no mechanical shutter

• Based on infra-red (IR) detectors sensing the high frequency flicker in the flame

• Low power consumption (10 Watt)

• 4 Selectable high pass filter characteristics for improved discrimination

• Constant flame signal over wide turndown range due to use of high frequency flicker flame

• Easily adjustable gain and threshold

• Easy access to viewing head lens for cleaning

• Quick disconnect plug at viewing head

• Available in 115VAC / 230VAC / 24VDC

• SIL 2 Certificate of testing D009_SV001 Rev2 to EIC 61508

• CE Approval

General Description

The Flame Eye Flame monitoring system consists of aviewing head, which is mounted on the burner front andpowered by remote signal processor unit. The signalprocessor unit is housed in an IP65 enclosure andconsists of signal processing circuitry, display drive,Flame “On/Off” relays, Fault relay and 4–20mAanalogue output for remote Flame indicator.

How It Works

The viewing head uses a solid-state photo detector thatresponds to the high frequency flicker in the flame. Thisfluctuating signal is then converted to balance signallines for transmission to the signal processor unit. Theuse of balanced signal lines enables a high rejection ofelectrical interference to be achieved.

Specifications

Electric Power Input AC Model – 115/230 VAC +10%–20%, 50/60Hz, 12VADC Model – 24 VDC +10%–10%, 10 WattOptical Silicon Viewing Head (Type FM2020SI)Spectral Response – 300nm to 1100nmEnvironmentalAmbient Temp. Control Unit 0°C–70°CViewing Head (FM2020SI) 0°C–125°CCase Temp. Viewing Head Housing 0°C–85°C

Cable (between Viewing Head & Control Unit)2 twisted pair overall braided screenOutputs from Control UnitFlame on Relay –1 Changeover contacts rate at 2A @ 230VACFault Relay –1 Changeover contacts rate 2A @ 230VACAnalogue Flame Signal –4–20mA for remote signalsTime Delay SettingsFlame on delay time fixed at 1 secondFlame off delay time fixed at 2 seconds

Flame Filter CharacteristicsChannel 1 18HzChannel 2 36HzChannel 3 72HzChannel 4 144HzSelf-Check TimePeriodic self check every 5 secondsError CodeE1 Internal faultE2 Flame on delay driver faultE3 Electronic shutter fault

Recommended