Publication 1794-IN002G-EN-P - January 2004 Installation Instructions FlexLogix Controller System Catalog numbers 1794-L33, 1794-L34, 1794-FLA Use this document as a guide for installing your FlexLogix ™ controller system. This document provides installation instructions for both the FlexLogix controller (1794-L33, -L34) and the FlexLogix extended-local I/O adapter (1794-FLA). You should already be familiar with the FlexLogix system components. See the documentation references for additional information. You must FLASH upgrade the firmware on your FlexLogix controller before you can use it. The controller ships with firmware revision 1.x but must be upgraded to match the version of RSLogix 5000 that you are using (e.g. if you are using RSLogix 5000 V11, you must upgrade your FlexLogix controller firmware to revision 11.x before using it). For more information on upgrading your controller’s firmware, see page 22. Tools That You Need You need the following tools to install your FlexLogix controller system. • slotted screwdriver • phillips screwdriver • mounting hardware (for mounting a DIN rail) • drill (for mounting a DIN rail) • needle-nose pliers Obtain a User Manual This product also has a user manual (pub. no. 1794-UM001). To view it, visit: www.theautomationbookstore.com. To purchase a manual, you can: • contact your local distributor or Rockwell Automation representative • visit www.theautomationbookstore.com and place an order • call 800.963.9548 (USA/Canada) or 001.320.725.1574 (outside USA/Canada)
Transcript
Installation Instructions
FlexLogix Controller System
Catalog numbers 1794-L33 1794-L34 1794-FLA
Use this document as a guide for installing your FlexLogixtrade controller system This document provides installation instructions for both the FlexLogix controller (1794-L33 -L34) and the FlexLogix extended-local IO adapter (1794-FLA) You should already be familiar with the FlexLogix system components See the documentation references for additional information
You must FLASH upgrade the firmware on your FlexLogix controller before you can use it The controller ships with firmware revision 1x but must be upgraded to match the version of RSLogix 5000 that you are using (eg if you are using RSLogix 5000 V11 you must upgrade your FlexLogix controller firmware to revision 11x before using it) For more information on upgrading your controllerrsquos firmware see page 22
Tools That You NeedYou need the following tools to install your FlexLogix controller system
bull slotted screwdriver
bull phillips screwdriver
bull mounting hardware (for mounting a DIN rail)
bull drill (for mounting a DIN rail)
bull needle-nose pliers
Obtain a User ManualThis product also has a user manual (pub no 1794-UM001) To view it visit wwwtheautomationbookstorecom To purchase a manual you can
bull contact your local distributor or Rockwell Automation representative
bull visit wwwtheautomationbookstorecom and place an order
bull call 8009639548 (USACanada) or 0013207251574 (outside USACanada)
Publication 1794-IN002G-EN-P - January 2004
2 FlexLogix Controller System
Important User Information
Solid state equipment has operational characteristics differing from those of electromechanical equipment Safety Guidelines for the Application Installation and Maintenance of Solid State Controls (Publication SGI-11 available from your local Rockwell Automation sales office or online at httpwwwabcommanualsgi) describes some important differences between solid state equipment and hard-wired electromechanical devices Because of this difference and also because of the wide variety of uses for solid state equipment all persons responsible for applying this equipment must satisfy themselves that each intended application of this equipment is acceptable
In no event will Rockwell Automation Inc be responsible or liable for indirect or consequential damages resulting from the use or application of this equipment
The examples and diagrams in this manual are included solely for illustrative purposes Because of the many variables and requirements associated with any particular installation Rockwell Automation Inc cannot assume responsibility or liability for actual use based on the examples and diagrams
No patent liability is assumed by Rockwell Automation Inc with respect to use of information circuits equipment or software described in this manual
Reproduction of the contents of this manual in whole or in part without written permission of Rockwell Automation Inc is prohibited
Throughout this manual we use notes to make you aware of safety considerations
WARNINGIdentifies information about practices or circumstances that can cause an explosion in a hazardous environment which may lead to personal injury or death property damage or economic loss
IMPORTANT Identifies information that is critical for successful application and understanding of the product
ATTENTION Identifies information about practices or circumstances that can lead to personal injury or death property damage or economic loss Attentions help you
bull identify a hazard
bull avoid a hazard
bull recognize the consequence
SHOCK HAZARD Labels may be located on or inside the drive to alert people that dangerous voltage may be present
BURN HAZARD Labels may be located on or inside the drive to alert people that surfaces may be dangerous temperatures
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 3
Environment and Enclosure
Prevent Electrostatic Discharge
ATTENTION This equipment is intended for use in a Pollution Degree 2 industrial environment in overvoltage Category II applications (as defined in IEC publication 60664-1) at altitudes up to 2000 meters without derating
This equipment is considered Group 1 Class A industrial equipment according to IECCISPR Publication 11 Without appropriate precautions there may be potential difficulties ensuring electromagnetic compatibility in other environments due to conducted as well as radiated disturbance
This equipment is supplied as open type equipment It must be mounted within an enclosure that is suitably designed for those specific environmental conditions that will be present and appropriately designed to prevent personal injury resulting from accessibility to live parts The interior of the enclosure must be accessible only by the use of a tool Subsequent sections of this publication may contain additional information regarding specific enclosure type ratings that are required to comply with certain product safety certifications
NOTE See NEMA Standards publication 250 and IEC publication 60529 as applicable for explanations of the degrees of protection provided by different types of enclosure Also see the appropriate sections in this publication as well as the Allen-Bradley publication 1770-41 (Industrial Automation Wiring and Grounding Guidelines) for additional installation requirements pertaining to this equipment
ATTENTION This equipment is sensitive to electrostatic discharge which can cause internal damage and affect normal operation Follow these guidelines when you handle this equipment
bull Touch a grounded object to discharge potential static
bull Wear an approved grounding wriststrap
bull Do not touch connectors or pins on component boards
bull Do not touch circuit components inside the equipment
bull If available use a static-safe workstation
bull When not in use store the equipment in appropriate static-safe packaging
Publication 1794-IN002G-EN-P - January 2004
4 FlexLogix Controller System
European Hazardous Location Approval
European Zone 2 Certification (The following applies when the product bears the EEx Marking)
This equipment is intended for use in potentially explosive atmospheres as defined by European Union Directive 949EC
The LCIE (Laboratoire Central des Industries Electriques) certifies that this equipment has been found to comply with the Essential Health and Safety Requirements relating to the design and construction of Category 3 equipment intended for use in potentially explosive atmospheres given in Annex II to this Directive The examination and test results are recorded in confidential report No 28 682 010
Compliance with the Essential Health and Safety Requirements has been assured by compliance with EN 50021
IMPORTANT When using this product also consider the following
bull This equipment is not resistant to sunlight or other sources of UV radiation
bull The secondary of a current transformer shall not be open-circuited when applied in Class I Zone 2 environments
bull Equipment of lesser Enclosure Type Rating must be installed in an enclosure providing at least IP54 protection when applied in Class I Zone 2 environments
bull This equipment shall be used within its specified ratings defined by Allen-Bradley
bull Provision shall be made to prevent the rated voltage from being exceeded by transient disturbances of more than 40 when applied in Class I Zone 2 environments
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 5
North American Hazardous Location ApprovalThe following information applies when operating this equipment in hazardous locations
Informations sur lrsquoutilisation de cet eacutequipement en environnements dangereux
Products marked ldquoCL I DIV 2 GP A B C Drdquo are suitable for use in Class I Division 2 Groups A B C D Hazardous Locations and nonhazardous locations only Each product is supplied with markings on the rating nameplate indicating the hazardous location temperature code When combining products within a system the most adverse temperature code (lowest ldquoTrdquo number) may be used to help determine the overall temperature code of the system Combinations of equipment in your system are subject to investigation by the local Authority Having Jurisdiction at the time of installation
Les produits marqueacutes CL I DIV 2 GP A B C D ne conviennent qursquoagrave une utilisation en environnements de Classe I Division 2 Groupes A B C D dangereux et non dangereux Chaque produit est livreacute avec des marquages sur sa plaque drsquoidentification qui indiquent le code de tempeacuterature pour les environnements dangereux Lorsque plusieurs produits sont combineacutes dans un systegraveme le code de tempeacuterature le plus deacutefavorable (code de tempeacuterature le plus faible) peut ecirctre utiliseacute pour deacuteterminer le code de tempeacuterature global du systegraveme Les combinaisons drsquoeacutequipements dans le systegraveme sont sujettes agrave inspection par les autoriteacutes locales qualifieacutees au moment de lrsquoinstallation
Publication 1794-IN002G-EN-P - January 2004
6 FlexLogix Controller System
WARNING EXPLOSION HAZARD
bull Do not disconnect equipment unless power has been removed or the area is known to be nonhazardous
bull Do not disconnect connections to this equipment unless power has been removed or the area is known to be nonhazardous Secure any external connections that mate to this equipment by using screws sliding latches threaded connectors or other means provided with this product
bull Substitution of components may impair suitability for Class I Division 2
bull If this product contains batteries they must only be changed in an area known to be nonhazardous
AVERTISSEMENT RISQUE DrsquoEXPLOSION
bull Couper le courant ou srsquoassurer que lrsquoenvironnement est classeacute non dangereux avant de deacutebrancher leacutequipement
bull Couper le courant ou sassurer que lrsquoenvironnement est classeacute non dangereux avant de deacutebrancher les connecteurs Fixer tous les connecteurs externes relieacutes agrave cet eacutequipement agrave laide de vis loquets coulissants connecteurs fileteacutes ou autres moyens fournis avec ce produit
bull La substitution de composants peut rendre cet eacutequipement inadapteacute agrave une utilisation en environnement de Classe I Division 2
bull Srsquoassurer que lrsquoenvironnement est classeacute non dangereux avant de changer les piles
The following information applies when operating this equipment in hazardous locations
Informations sur lrsquoutilisation de cet eacutequipement en environnements dangereux
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 7
Removal and Insertion Under PowerThe FlexLogix controller the extended-local IO adapter the communication daughtercards and the IO terminal bases cannot be removed or inserted under power
However you can remove and insert FLEX IO modules while backplane power is applied and the system is operating
Be sure that power is removed or the area is nonhazardous before proceeding
Other Considerations
WARNING If you insert or remove the module while backplane power is on an electrical arc can occur This could cause an explosion in hazardous location installations
ATTENTION Also consider the following before you install your FlexLogix controller
bull This product is grounded through the DIN rail to chassis ground Use zinc plated yellow-chromate steel DIN rail to assure proper grounding The use of other DIN rail materials (eg aluminum plastic etc) that can corrode oxidize or are poor conductors can result in improper or intermittent grounding
bull Power connection length should be less than 10 meters
Publication 1794-IN002G-EN-P - January 2004
8 FlexLogix Controller System
What You Need to DoBefore you can install a FlexLogix controller or extended-local adapter you must
Install steel 35 x 755mm DIN rails (A-B part number 199-DR1 46277-3) where you want to place the FlexLogix system components
The DIN rails for all FlexLogix system components including all local and extended-local IO modules must be mounted on a common conductive surface to ensure proper electromagnetic interference (EMI) performance See 24 and 25 for approximate mounting dimensions and mounting clearances
For more information about mounting DIN rails and splitting IO across DIN rails see the FLEX IO Product Data publication 1794-21
Use DIN rail locks (A-B catalog number 1492-EA35) to meet the shock and vibrations specifications listed on 26 A pair of DIN locks comes with the controller
Mount an appropriate power supply on an appropriate DIN rail See the specifications on 26
To install a FlexLogix controller
Step 1 Verify That You Have All the Components see page 9
Step 2 Install the Battery see page 10
Step 3 Install Communication Daughtercards (optional) see page 11
Step 4 Install the Controller see page 12
Step 5 Install the Extended-Local Adapter (optional) see page 15
After you install the FlexLogix controller you can
Make an RS-232 Connection to the Controller see page 18
Select the Operating Mode of the Controller see page 21
Monitor the Controller LEDs see page 22
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 9
Step 1 Verify That You Have All the ComponentsThese components ship with the FlexLogix controller
bull 1756-BA1 battery and label
bull key
bull one spring-clip connector plug for 24V power connection
bull one screw-terminal connector plug for 24V power connection
bull two 1492-EA35 DIN rail locks
The system components you have depend on your application You might have
FlexLogix System Component Description
1788-CNC -CNCR for ControlNet communications1788-CNF -CNFR for ControlNet communications1788-DNBO for DeviceNet communications1788-ENBT for EtherNetIP communications
1756-CP3You can also use the 1747-CP3 cable from the SLC product family
1794-FLA
1794-CE1 (1 foot)1794-CE3 (3 foot)
communication card
serial cable
FlexLogix extended-local adapter
extended- local IO cable
Publication 1794-IN002G-EN-P - January 2004
10 FlexLogix Controller System
Step 2 Install the Battery
For Safety information on the handling of lithium batteries including handling and disposal of leaking batteries see Guidelines for Handling Lithium Batteries publication AG 5-4
1 Install a 1756-BA1 battery
2 Attach the battery label
a Write on the battery label the date you install the battery
b Attach the label to the inside of the battery compartment
ATTENTION Only install a 1756-BA1 battery If you install a different battery you may damage the controller
WARNING For safety information on the handling of lithium batteries in-cluding the handling and disposal of leaking batteries see Guide-lines for Handling Lithium Batteries publication AG-54Store batteries in a cool dry environment We recommend 25degC with 40 to 60 relative humidity You may store batteries for up to 30 days between -45deg to 85degC such as during transporta-tion To avoid possible leakage do not store batteries above 60degC for more than 30 days
When you connect or disconnect the battery an electrical arc can occur This could cause an explosion in hazardous location in-stallations Be sure that power is removed or the area is nonhaz-ardous before proceeding
Attach battery here
top red lead (+)
middle black lead (-)
bottom no connection
Attach label here
This jumper is for service use only Do not use this jumper
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 11
Step 3 Install Communication Daughtercards (optional)
For specific information about configuring the communication card (such as setting a node address) see the installation instructions for the communication card
1 Turn off power to the controller
2 If necessary remove the blank cover from the communication slot
3 Slide the communication card into the communication slot Be sure to line up the card with the card guides in the controller
4 Record which slot you use for the communication card You need the slot number when you develop your controller application
5 Secure the card with the screws to ensure proper grounding Do not over-tighten the screws The maximum torque for the card screws is 48 to 52 inch pounds (05 to 06 Nm)
6 After the controller is installed (see page 12) connect the network cable
Removing a Communication CardIf you need to remove a communication card from the controller
1 Turn off power to the controller
2 Disconnect all cables from the communication card
3 Loosen the card screws from the communication card
4 Remove the card from the controller
5 Replace the card with a blank cover or a different communication card
WARNING If you insert or remove the card while host power is on an electrical arc can occur This could cause an explosion in haz-ardous location installations
31032-M
slot 1slot 2
Publication 1794-IN002G-EN-P - January 2004
12 FlexLogix Controller System
Step 4 Install the Controller
1 Position the FlexLogix controller on the DIN rail at a 5deg angle and rotate the controller onto the DIN rail
2 Press the controller down onto the DIN rail until flush The locking tabs will snap into position and lock the controller onto the DIN rail
If the controller does not lock in place use a screwdriver or similar device to move the locking tabs down while pressing the controller onto the DIN rail Release the locking tabs to lock the controller in place If necessary push up on the locking tabs to lock
3 Ground the controller The DIN rail and the common conductive surface behind the DIN rail provide functional ground for the controller Use the grounding stud to meet safety ground requirements
For information about wiring and grounding see the Industrial Automation Wiring and Grounding Guidelines publication 1770-41
IMPORTANT You can mount the FlexLogix controller either vertically or horizontally (as shown)
A
A
locking tabs
grounding stud
Equipment grounding conductor (ground lug with 208 sq mm [14 AWG] wire) to ground bus
nuts with captive star washer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 13
4 Make sure power is not applied to the power supply
5 Connect the power supply to the controller The graphic below and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the top of the controller connector terminal A to the bottom left power connector terminal G
b Connect -24V common to top controller connector terminal B to the top left power connector terminal E
c Use connections C and D on the controller and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the controller to meet the requirements for installations in Class I Division 2 locations
WARNING If you connect or disconnect wiring while the field-side power is on an electrical arc can occur This could cause an explosion in hazardous location installations Be sure that power is re-moved or the area is nonhazardous before proceeding
+
+
A
B
C
D
FE
HG
_
_
Publication 1794-IN002G-EN-P - January 2004
14 FlexLogix Controller System
6 Mount the IO terminal bases on the DIN rail
For information about IO terminal bases see the FLEX IO Terminal Base Installation Instructions publication 1794-IN092
7 Install the IO modules
To install an IO module see the installation instructions for that module
Removing the controllerIf you need to remove the controller follow these steps
1 Turn off power to the controller
2 Disconnect all cables from the controller
3 Remove the IO module that is adjacent to the controller
4 On the terminal base adjacent to the controller slide the FLEXBUS connector away from the controller and remove the IO terminal base
5 Remove the controller from the DIN rail
B
A
A
31036-M
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 15
Step 5 Install the Extended-Local Adapter (optional)
1 Position the 1794-FLA extended-local IO adapter on the DIN rail at a 30deg angle and rotate the adapter onto the DIN rail
2 Press the adapter down onto the DIN rail until flush The locking tab will snap into position and lock the adapter onto the DIN rail
If the adapter does not lock in place use a screwdriver or similar device to move the locking tab down while pressing the adapter onto the DIN rail Release the locking tab to lock the adapter in place If necessary push up on the locking tab to lock
3 Ground the adapter The adapter is grounded through the steel DIN rail and the common conductive surface behind the DIN rail Additionally use the grounding stud
grounding stud
Equipment grounding conductor (ground lug with 208 sq mm [14 AWG] wire) to ground bus
nuts with captive star washer
Publication 1794-IN002G-EN-P - January 2004
16 FlexLogix Controller System
4 Make sure power is not applied to the power supply Connect the power supply to the adapter This diagram and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the left adapter connector terminal A to the bottom left power connector terminal G
b Connect -24V common to left adapter connector terminal B to the top left power connector terminal E
c Use connections C and D on the adapter and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the adapter to meet the requirements for installations in Class I Division 2 locations
5 Connect IO terminal bases and IO modules to the adapter the same way you connect them to the controller
6 Remove the plastic spacer from both ends of the extended-local IO cable (1794-CE1 or 1794-CE3)
plastic spacer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 17
7 Connect the adapter to the controller
The following diagram shows how you can also use the 1794-CE1 -CE3 cable to split a rail of IO You can split each rail only once You can split a rail right after the controller (or adapter) or after any IO module For more information about the 1794-CE1 -CE3 cables see the Interconnect Cable Installation Instructions publication 1794-512
Removing the extended-local adapterIf you need to remove the adapter follow these steps
1 Turn off power to the adapter
2 Disconnect all cables from the adapter
3 Remove the IO module that is adjacent to the adapter
4 On the terminal base adjacent to the adapter slide the FLEXBUS connector away from the adapter and remove the IO terminal base
5 Remove the adapter from the DIN rail
31039-M
1794-CE1 or 1794-CE3 cable
LOCAL rail
LOCAL2 rail
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
Publication 1794-IN002G-EN-P - January 2004
18 FlexLogix Controller System
Make an RS-232 Connection to the ControllerThe RS-232 port is a non-isolated serial port built-in to the front of the controller
To connect to the serial port
1 Determine whether you need an optical isolator
If you connect the controller to a device outside of the systemrsquos enclosure consider installing an isolator between the controller and device
One possible isolator is the 1761-NET-AIC interface converter
serial port
port 1 DB-9 RS-232 DTE
baud rate selector switch
port 2 mini-DIN 8 RS-232
dc power source selector switch
terminals for external 24V dc power supply
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 19
2 Select the appropriate cable
Are you using an isolator
Use this cable
no The 1756-CP3 cable attaches the controller directly to the controller
If you make your own cable it must be shielded and the shields must be tied to the metal shell (that surrounds the pins) on both ends of the cableYou can also use a 1747-CP3 cable (from the SLC product family) This cable has a taller right-angle connector housing than the 1756-CP3 cable
yes The 1761-CBL-AP00 cable (right-angle connector to controller) or the 1761-CBL-PM02 cable (straight connector to the controller) attaches the controller to port 2 on the 1761-NET-AIC isolator The mini-DIN connector is not commercially available so you cannot make this cable
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
DB-9 right-angle or straight cable end 8-pin mini-DIN cable end
Pin DB-9 end Mini-DIN end1 DCD DCD
2 RxD RxD
3 TxD TxD
4 DTR DTR
5 ground ground
6 DSR DSR
7 RTS RTS
8 CTS CTS
9 na na
1 2
34
5
6 7867
8
9
1
2
3
4
5
Publication 1794-IN002G-EN-P - January 2004
20 FlexLogix Controller System
3 Connect the appropriate cable to the serial port on the controller
Be sure that power is removed or the area is nonhazardous before proceeding
4 If necessary attach the controller to the isolator
WARNING If you connect or disconnect the serial cable with power applied to this module or the serial device on the other end of the cable an electrical arc can occur This could cause an explosion in hazardous location installations
modem
1761-NET-AIC isolator
user-supplied modem cable
1761 cable
system enclosure
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 21
Select the Operating Mode of the Controller
1 Use this table to determine the operating mode of the controller
2 Turn the key on the front panel of the controller to select the mode
If you want to Select one of these modes
Run Program Remote
Run Program Test
turn outputs to the state commanded by the logic of the project
YES YES
turn outputs to their configured state for Program mode
YES YES YES
execute (scan) tasks YES YES YES
change the mode of the controller through software
YES YES YES
download a project YES YES
schedule a ControlNet network YES YES
while online edit the project YES YES YES YES
To select Turn the key to
Remote Run RUN and then to REM
Remote Program PROG and then to REM
Remote Test REM and then go online and select Test mode via the programming software
keyswitch
Publication 1794-IN002G-EN-P - January 2004
22 FlexLogix Controller System
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware RevisionTo update the firmware of a controller first install a firmware upgrade kit
bull An upgrade kit ships on a supplemental CD along with RSLogix 5000 software
bull To download an upgrade kit go to httpsupportrockwellautomationcom Choose Firmware Updates
Indicator Color Description
RUN off bull no task(s) running
bull controller in Program mode
green bull one or more tasks are running
bull controller is in Run mode
OK off no power applied
red flashing after initially installing the controller - the controller requires a FLASH upgrade to the proper firmware revision see belowafter the controller is operating - recoverable fault
red bull controller faulted
bull clear faults clear memory or replace the controller
green controller OK
BATTERY off battery will support memory
red bull battery may not support memory
bull replace battery
IO off bull controller project not downloaded (the condition after power up)
bull no IO or communications configured
green communicating to all devices
green flashing one or more devices are not responding
LOCALandLOCAL2
off rail is inhibited
green communicating to all devices on that rail
green flashing one or more devices on that rail not responding
red flashing no modules exist on that rail
RS232 off no activity
green data being received or transmitted
FORCE off no forces present
amber forces present
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 23
Update the Controller
1 Connect the controller to the same network as your workstation
2 Start ControlFLASH software
3 Choose Next gt
4 Select the catalog number of the controller and choose Next gt
5 Expand the network until you see the controller If the required network is not shown first configure a driver for the network in RSLinx software
6 Select the controller and choose OK
7 Select the revision level to which you want to update the controller and choose Next gt
8 To start the update of the controller choose Finish and then Yes
After the controller is updated the status box displays Update complete
9 Choose OK
10 To close ControlFLASH software choose Cancel and then Yes
TIP RSLogix 5000 software revision 100 or later lets you update controller firmware as part of the download sequence To update the controller download your project and follow the prompts of the software
IMPORTANT If the Revision list is empty download a new upgrade kit Some older upgrade kits do not work with new controllers
weight 1794-L33 71 kg (156 lbs oz)1794-L34 75 g (166 lbs)(no communication cards installed)
28 kg (62 lbs)
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 27
power supply 1794-PS3 or 1794-PS13 ndash In applications that must be compliant with CSA requirements use a Separated Extra-Low Voltage (SELV) power supply that is compliant with IEC 610101 Annex H
power conductors 60deg C (140deg F) minimum copper22 to 14 AWG (0324 to 208 sq mm) stranded364 inch (12mm) insulation maximumlength 10m or less
category 3(2)
power connector torque 5 to 7 inch-pounds (06 to 08Nm)
battery 1756-BA1 (AB part number 94194801)059g lithium
na
serial cable 1761-CBLPM02 to 1761-NET-AIC 1761-CBLPA00 to 1761-NET-AIC1756-CP3 directly to controller1747-CP3 directly to controller
DIN rail steel 35 x 755mm DIN railA-B part number 199-DR1 46277-3 EN 50022
operating temperature IEC 60068-2-1 (Test Ad Operating Cold)IEC 60068-2-2 (Test Bd Operating Dry Heat)IEC 60068-2-14 (Test Nb Operating Thermal Shock)0 to 60degC (32 to 140degF)
storage temperature IEC 60068-2-1 (Test Ab Un-packaged Non-operating Cold)IEC 60068-2-2 (Test Bb Un-packaged Non-operating Dry Heat)IEC 60068-2-14 (Test Na Un-packaged Non-operating Thermal Shock)ndash40 to 85degC (ndash40 to 185degF)
relative humidity IEC 60068-2-30 (Test Db Un-packaged Non-operating Damp Heat)5 to 95 non-condensing
vibration(3) IEC60068-2-6 (Test Fc Operating) 5g 10-500Hz
shock(3)
operatingnon-operating
IEC60068-2-27 (Test Ea Unpackaged shock)
30g50g
emissions CISPR 11Group 1 Class A (with appropriate enclosure)
ESD immunity IEC 61000-4-26kV contact discharges8kV air discharges
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
RA-QR005C-EN-E 608
2 FlexLogix Controller System
Important User Information
Solid state equipment has operational characteristics differing from those of electromechanical equipment Safety Guidelines for the Application Installation and Maintenance of Solid State Controls (Publication SGI-11 available from your local Rockwell Automation sales office or online at httpwwwabcommanualsgi) describes some important differences between solid state equipment and hard-wired electromechanical devices Because of this difference and also because of the wide variety of uses for solid state equipment all persons responsible for applying this equipment must satisfy themselves that each intended application of this equipment is acceptable
In no event will Rockwell Automation Inc be responsible or liable for indirect or consequential damages resulting from the use or application of this equipment
The examples and diagrams in this manual are included solely for illustrative purposes Because of the many variables and requirements associated with any particular installation Rockwell Automation Inc cannot assume responsibility or liability for actual use based on the examples and diagrams
No patent liability is assumed by Rockwell Automation Inc with respect to use of information circuits equipment or software described in this manual
Reproduction of the contents of this manual in whole or in part without written permission of Rockwell Automation Inc is prohibited
Throughout this manual we use notes to make you aware of safety considerations
WARNINGIdentifies information about practices or circumstances that can cause an explosion in a hazardous environment which may lead to personal injury or death property damage or economic loss
IMPORTANT Identifies information that is critical for successful application and understanding of the product
ATTENTION Identifies information about practices or circumstances that can lead to personal injury or death property damage or economic loss Attentions help you
bull identify a hazard
bull avoid a hazard
bull recognize the consequence
SHOCK HAZARD Labels may be located on or inside the drive to alert people that dangerous voltage may be present
BURN HAZARD Labels may be located on or inside the drive to alert people that surfaces may be dangerous temperatures
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 3
Environment and Enclosure
Prevent Electrostatic Discharge
ATTENTION This equipment is intended for use in a Pollution Degree 2 industrial environment in overvoltage Category II applications (as defined in IEC publication 60664-1) at altitudes up to 2000 meters without derating
This equipment is considered Group 1 Class A industrial equipment according to IECCISPR Publication 11 Without appropriate precautions there may be potential difficulties ensuring electromagnetic compatibility in other environments due to conducted as well as radiated disturbance
This equipment is supplied as open type equipment It must be mounted within an enclosure that is suitably designed for those specific environmental conditions that will be present and appropriately designed to prevent personal injury resulting from accessibility to live parts The interior of the enclosure must be accessible only by the use of a tool Subsequent sections of this publication may contain additional information regarding specific enclosure type ratings that are required to comply with certain product safety certifications
NOTE See NEMA Standards publication 250 and IEC publication 60529 as applicable for explanations of the degrees of protection provided by different types of enclosure Also see the appropriate sections in this publication as well as the Allen-Bradley publication 1770-41 (Industrial Automation Wiring and Grounding Guidelines) for additional installation requirements pertaining to this equipment
ATTENTION This equipment is sensitive to electrostatic discharge which can cause internal damage and affect normal operation Follow these guidelines when you handle this equipment
bull Touch a grounded object to discharge potential static
bull Wear an approved grounding wriststrap
bull Do not touch connectors or pins on component boards
bull Do not touch circuit components inside the equipment
bull If available use a static-safe workstation
bull When not in use store the equipment in appropriate static-safe packaging
Publication 1794-IN002G-EN-P - January 2004
4 FlexLogix Controller System
European Hazardous Location Approval
European Zone 2 Certification (The following applies when the product bears the EEx Marking)
This equipment is intended for use in potentially explosive atmospheres as defined by European Union Directive 949EC
The LCIE (Laboratoire Central des Industries Electriques) certifies that this equipment has been found to comply with the Essential Health and Safety Requirements relating to the design and construction of Category 3 equipment intended for use in potentially explosive atmospheres given in Annex II to this Directive The examination and test results are recorded in confidential report No 28 682 010
Compliance with the Essential Health and Safety Requirements has been assured by compliance with EN 50021
IMPORTANT When using this product also consider the following
bull This equipment is not resistant to sunlight or other sources of UV radiation
bull The secondary of a current transformer shall not be open-circuited when applied in Class I Zone 2 environments
bull Equipment of lesser Enclosure Type Rating must be installed in an enclosure providing at least IP54 protection when applied in Class I Zone 2 environments
bull This equipment shall be used within its specified ratings defined by Allen-Bradley
bull Provision shall be made to prevent the rated voltage from being exceeded by transient disturbances of more than 40 when applied in Class I Zone 2 environments
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 5
North American Hazardous Location ApprovalThe following information applies when operating this equipment in hazardous locations
Informations sur lrsquoutilisation de cet eacutequipement en environnements dangereux
Products marked ldquoCL I DIV 2 GP A B C Drdquo are suitable for use in Class I Division 2 Groups A B C D Hazardous Locations and nonhazardous locations only Each product is supplied with markings on the rating nameplate indicating the hazardous location temperature code When combining products within a system the most adverse temperature code (lowest ldquoTrdquo number) may be used to help determine the overall temperature code of the system Combinations of equipment in your system are subject to investigation by the local Authority Having Jurisdiction at the time of installation
Les produits marqueacutes CL I DIV 2 GP A B C D ne conviennent qursquoagrave une utilisation en environnements de Classe I Division 2 Groupes A B C D dangereux et non dangereux Chaque produit est livreacute avec des marquages sur sa plaque drsquoidentification qui indiquent le code de tempeacuterature pour les environnements dangereux Lorsque plusieurs produits sont combineacutes dans un systegraveme le code de tempeacuterature le plus deacutefavorable (code de tempeacuterature le plus faible) peut ecirctre utiliseacute pour deacuteterminer le code de tempeacuterature global du systegraveme Les combinaisons drsquoeacutequipements dans le systegraveme sont sujettes agrave inspection par les autoriteacutes locales qualifieacutees au moment de lrsquoinstallation
Publication 1794-IN002G-EN-P - January 2004
6 FlexLogix Controller System
WARNING EXPLOSION HAZARD
bull Do not disconnect equipment unless power has been removed or the area is known to be nonhazardous
bull Do not disconnect connections to this equipment unless power has been removed or the area is known to be nonhazardous Secure any external connections that mate to this equipment by using screws sliding latches threaded connectors or other means provided with this product
bull Substitution of components may impair suitability for Class I Division 2
bull If this product contains batteries they must only be changed in an area known to be nonhazardous
AVERTISSEMENT RISQUE DrsquoEXPLOSION
bull Couper le courant ou srsquoassurer que lrsquoenvironnement est classeacute non dangereux avant de deacutebrancher leacutequipement
bull Couper le courant ou sassurer que lrsquoenvironnement est classeacute non dangereux avant de deacutebrancher les connecteurs Fixer tous les connecteurs externes relieacutes agrave cet eacutequipement agrave laide de vis loquets coulissants connecteurs fileteacutes ou autres moyens fournis avec ce produit
bull La substitution de composants peut rendre cet eacutequipement inadapteacute agrave une utilisation en environnement de Classe I Division 2
bull Srsquoassurer que lrsquoenvironnement est classeacute non dangereux avant de changer les piles
The following information applies when operating this equipment in hazardous locations
Informations sur lrsquoutilisation de cet eacutequipement en environnements dangereux
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 7
Removal and Insertion Under PowerThe FlexLogix controller the extended-local IO adapter the communication daughtercards and the IO terminal bases cannot be removed or inserted under power
However you can remove and insert FLEX IO modules while backplane power is applied and the system is operating
Be sure that power is removed or the area is nonhazardous before proceeding
Other Considerations
WARNING If you insert or remove the module while backplane power is on an electrical arc can occur This could cause an explosion in hazardous location installations
ATTENTION Also consider the following before you install your FlexLogix controller
bull This product is grounded through the DIN rail to chassis ground Use zinc plated yellow-chromate steel DIN rail to assure proper grounding The use of other DIN rail materials (eg aluminum plastic etc) that can corrode oxidize or are poor conductors can result in improper or intermittent grounding
bull Power connection length should be less than 10 meters
Publication 1794-IN002G-EN-P - January 2004
8 FlexLogix Controller System
What You Need to DoBefore you can install a FlexLogix controller or extended-local adapter you must
Install steel 35 x 755mm DIN rails (A-B part number 199-DR1 46277-3) where you want to place the FlexLogix system components
The DIN rails for all FlexLogix system components including all local and extended-local IO modules must be mounted on a common conductive surface to ensure proper electromagnetic interference (EMI) performance See 24 and 25 for approximate mounting dimensions and mounting clearances
For more information about mounting DIN rails and splitting IO across DIN rails see the FLEX IO Product Data publication 1794-21
Use DIN rail locks (A-B catalog number 1492-EA35) to meet the shock and vibrations specifications listed on 26 A pair of DIN locks comes with the controller
Mount an appropriate power supply on an appropriate DIN rail See the specifications on 26
To install a FlexLogix controller
Step 1 Verify That You Have All the Components see page 9
Step 2 Install the Battery see page 10
Step 3 Install Communication Daughtercards (optional) see page 11
Step 4 Install the Controller see page 12
Step 5 Install the Extended-Local Adapter (optional) see page 15
After you install the FlexLogix controller you can
Make an RS-232 Connection to the Controller see page 18
Select the Operating Mode of the Controller see page 21
Monitor the Controller LEDs see page 22
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 9
Step 1 Verify That You Have All the ComponentsThese components ship with the FlexLogix controller
bull 1756-BA1 battery and label
bull key
bull one spring-clip connector plug for 24V power connection
bull one screw-terminal connector plug for 24V power connection
bull two 1492-EA35 DIN rail locks
The system components you have depend on your application You might have
FlexLogix System Component Description
1788-CNC -CNCR for ControlNet communications1788-CNF -CNFR for ControlNet communications1788-DNBO for DeviceNet communications1788-ENBT for EtherNetIP communications
1756-CP3You can also use the 1747-CP3 cable from the SLC product family
1794-FLA
1794-CE1 (1 foot)1794-CE3 (3 foot)
communication card
serial cable
FlexLogix extended-local adapter
extended- local IO cable
Publication 1794-IN002G-EN-P - January 2004
10 FlexLogix Controller System
Step 2 Install the Battery
For Safety information on the handling of lithium batteries including handling and disposal of leaking batteries see Guidelines for Handling Lithium Batteries publication AG 5-4
1 Install a 1756-BA1 battery
2 Attach the battery label
a Write on the battery label the date you install the battery
b Attach the label to the inside of the battery compartment
ATTENTION Only install a 1756-BA1 battery If you install a different battery you may damage the controller
WARNING For safety information on the handling of lithium batteries in-cluding the handling and disposal of leaking batteries see Guide-lines for Handling Lithium Batteries publication AG-54Store batteries in a cool dry environment We recommend 25degC with 40 to 60 relative humidity You may store batteries for up to 30 days between -45deg to 85degC such as during transporta-tion To avoid possible leakage do not store batteries above 60degC for more than 30 days
When you connect or disconnect the battery an electrical arc can occur This could cause an explosion in hazardous location in-stallations Be sure that power is removed or the area is nonhaz-ardous before proceeding
Attach battery here
top red lead (+)
middle black lead (-)
bottom no connection
Attach label here
This jumper is for service use only Do not use this jumper
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 11
Step 3 Install Communication Daughtercards (optional)
For specific information about configuring the communication card (such as setting a node address) see the installation instructions for the communication card
1 Turn off power to the controller
2 If necessary remove the blank cover from the communication slot
3 Slide the communication card into the communication slot Be sure to line up the card with the card guides in the controller
4 Record which slot you use for the communication card You need the slot number when you develop your controller application
5 Secure the card with the screws to ensure proper grounding Do not over-tighten the screws The maximum torque for the card screws is 48 to 52 inch pounds (05 to 06 Nm)
6 After the controller is installed (see page 12) connect the network cable
Removing a Communication CardIf you need to remove a communication card from the controller
1 Turn off power to the controller
2 Disconnect all cables from the communication card
3 Loosen the card screws from the communication card
4 Remove the card from the controller
5 Replace the card with a blank cover or a different communication card
WARNING If you insert or remove the card while host power is on an electrical arc can occur This could cause an explosion in haz-ardous location installations
31032-M
slot 1slot 2
Publication 1794-IN002G-EN-P - January 2004
12 FlexLogix Controller System
Step 4 Install the Controller
1 Position the FlexLogix controller on the DIN rail at a 5deg angle and rotate the controller onto the DIN rail
2 Press the controller down onto the DIN rail until flush The locking tabs will snap into position and lock the controller onto the DIN rail
If the controller does not lock in place use a screwdriver or similar device to move the locking tabs down while pressing the controller onto the DIN rail Release the locking tabs to lock the controller in place If necessary push up on the locking tabs to lock
3 Ground the controller The DIN rail and the common conductive surface behind the DIN rail provide functional ground for the controller Use the grounding stud to meet safety ground requirements
For information about wiring and grounding see the Industrial Automation Wiring and Grounding Guidelines publication 1770-41
IMPORTANT You can mount the FlexLogix controller either vertically or horizontally (as shown)
A
A
locking tabs
grounding stud
Equipment grounding conductor (ground lug with 208 sq mm [14 AWG] wire) to ground bus
nuts with captive star washer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 13
4 Make sure power is not applied to the power supply
5 Connect the power supply to the controller The graphic below and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the top of the controller connector terminal A to the bottom left power connector terminal G
b Connect -24V common to top controller connector terminal B to the top left power connector terminal E
c Use connections C and D on the controller and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the controller to meet the requirements for installations in Class I Division 2 locations
WARNING If you connect or disconnect wiring while the field-side power is on an electrical arc can occur This could cause an explosion in hazardous location installations Be sure that power is re-moved or the area is nonhazardous before proceeding
+
+
A
B
C
D
FE
HG
_
_
Publication 1794-IN002G-EN-P - January 2004
14 FlexLogix Controller System
6 Mount the IO terminal bases on the DIN rail
For information about IO terminal bases see the FLEX IO Terminal Base Installation Instructions publication 1794-IN092
7 Install the IO modules
To install an IO module see the installation instructions for that module
Removing the controllerIf you need to remove the controller follow these steps
1 Turn off power to the controller
2 Disconnect all cables from the controller
3 Remove the IO module that is adjacent to the controller
4 On the terminal base adjacent to the controller slide the FLEXBUS connector away from the controller and remove the IO terminal base
5 Remove the controller from the DIN rail
B
A
A
31036-M
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 15
Step 5 Install the Extended-Local Adapter (optional)
1 Position the 1794-FLA extended-local IO adapter on the DIN rail at a 30deg angle and rotate the adapter onto the DIN rail
2 Press the adapter down onto the DIN rail until flush The locking tab will snap into position and lock the adapter onto the DIN rail
If the adapter does not lock in place use a screwdriver or similar device to move the locking tab down while pressing the adapter onto the DIN rail Release the locking tab to lock the adapter in place If necessary push up on the locking tab to lock
3 Ground the adapter The adapter is grounded through the steel DIN rail and the common conductive surface behind the DIN rail Additionally use the grounding stud
grounding stud
Equipment grounding conductor (ground lug with 208 sq mm [14 AWG] wire) to ground bus
nuts with captive star washer
Publication 1794-IN002G-EN-P - January 2004
16 FlexLogix Controller System
4 Make sure power is not applied to the power supply Connect the power supply to the adapter This diagram and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the left adapter connector terminal A to the bottom left power connector terminal G
b Connect -24V common to left adapter connector terminal B to the top left power connector terminal E
c Use connections C and D on the adapter and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the adapter to meet the requirements for installations in Class I Division 2 locations
5 Connect IO terminal bases and IO modules to the adapter the same way you connect them to the controller
6 Remove the plastic spacer from both ends of the extended-local IO cable (1794-CE1 or 1794-CE3)
plastic spacer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 17
7 Connect the adapter to the controller
The following diagram shows how you can also use the 1794-CE1 -CE3 cable to split a rail of IO You can split each rail only once You can split a rail right after the controller (or adapter) or after any IO module For more information about the 1794-CE1 -CE3 cables see the Interconnect Cable Installation Instructions publication 1794-512
Removing the extended-local adapterIf you need to remove the adapter follow these steps
1 Turn off power to the adapter
2 Disconnect all cables from the adapter
3 Remove the IO module that is adjacent to the adapter
4 On the terminal base adjacent to the adapter slide the FLEXBUS connector away from the adapter and remove the IO terminal base
5 Remove the adapter from the DIN rail
31039-M
1794-CE1 or 1794-CE3 cable
LOCAL rail
LOCAL2 rail
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
Publication 1794-IN002G-EN-P - January 2004
18 FlexLogix Controller System
Make an RS-232 Connection to the ControllerThe RS-232 port is a non-isolated serial port built-in to the front of the controller
To connect to the serial port
1 Determine whether you need an optical isolator
If you connect the controller to a device outside of the systemrsquos enclosure consider installing an isolator between the controller and device
One possible isolator is the 1761-NET-AIC interface converter
serial port
port 1 DB-9 RS-232 DTE
baud rate selector switch
port 2 mini-DIN 8 RS-232
dc power source selector switch
terminals for external 24V dc power supply
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 19
2 Select the appropriate cable
Are you using an isolator
Use this cable
no The 1756-CP3 cable attaches the controller directly to the controller
If you make your own cable it must be shielded and the shields must be tied to the metal shell (that surrounds the pins) on both ends of the cableYou can also use a 1747-CP3 cable (from the SLC product family) This cable has a taller right-angle connector housing than the 1756-CP3 cable
yes The 1761-CBL-AP00 cable (right-angle connector to controller) or the 1761-CBL-PM02 cable (straight connector to the controller) attaches the controller to port 2 on the 1761-NET-AIC isolator The mini-DIN connector is not commercially available so you cannot make this cable
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
DB-9 right-angle or straight cable end 8-pin mini-DIN cable end
Pin DB-9 end Mini-DIN end1 DCD DCD
2 RxD RxD
3 TxD TxD
4 DTR DTR
5 ground ground
6 DSR DSR
7 RTS RTS
8 CTS CTS
9 na na
1 2
34
5
6 7867
8
9
1
2
3
4
5
Publication 1794-IN002G-EN-P - January 2004
20 FlexLogix Controller System
3 Connect the appropriate cable to the serial port on the controller
Be sure that power is removed or the area is nonhazardous before proceeding
4 If necessary attach the controller to the isolator
WARNING If you connect or disconnect the serial cable with power applied to this module or the serial device on the other end of the cable an electrical arc can occur This could cause an explosion in hazardous location installations
modem
1761-NET-AIC isolator
user-supplied modem cable
1761 cable
system enclosure
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 21
Select the Operating Mode of the Controller
1 Use this table to determine the operating mode of the controller
2 Turn the key on the front panel of the controller to select the mode
If you want to Select one of these modes
Run Program Remote
Run Program Test
turn outputs to the state commanded by the logic of the project
YES YES
turn outputs to their configured state for Program mode
YES YES YES
execute (scan) tasks YES YES YES
change the mode of the controller through software
YES YES YES
download a project YES YES
schedule a ControlNet network YES YES
while online edit the project YES YES YES YES
To select Turn the key to
Remote Run RUN and then to REM
Remote Program PROG and then to REM
Remote Test REM and then go online and select Test mode via the programming software
keyswitch
Publication 1794-IN002G-EN-P - January 2004
22 FlexLogix Controller System
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware RevisionTo update the firmware of a controller first install a firmware upgrade kit
bull An upgrade kit ships on a supplemental CD along with RSLogix 5000 software
bull To download an upgrade kit go to httpsupportrockwellautomationcom Choose Firmware Updates
Indicator Color Description
RUN off bull no task(s) running
bull controller in Program mode
green bull one or more tasks are running
bull controller is in Run mode
OK off no power applied
red flashing after initially installing the controller - the controller requires a FLASH upgrade to the proper firmware revision see belowafter the controller is operating - recoverable fault
red bull controller faulted
bull clear faults clear memory or replace the controller
green controller OK
BATTERY off battery will support memory
red bull battery may not support memory
bull replace battery
IO off bull controller project not downloaded (the condition after power up)
bull no IO or communications configured
green communicating to all devices
green flashing one or more devices are not responding
LOCALandLOCAL2
off rail is inhibited
green communicating to all devices on that rail
green flashing one or more devices on that rail not responding
red flashing no modules exist on that rail
RS232 off no activity
green data being received or transmitted
FORCE off no forces present
amber forces present
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 23
Update the Controller
1 Connect the controller to the same network as your workstation
2 Start ControlFLASH software
3 Choose Next gt
4 Select the catalog number of the controller and choose Next gt
5 Expand the network until you see the controller If the required network is not shown first configure a driver for the network in RSLinx software
6 Select the controller and choose OK
7 Select the revision level to which you want to update the controller and choose Next gt
8 To start the update of the controller choose Finish and then Yes
After the controller is updated the status box displays Update complete
9 Choose OK
10 To close ControlFLASH software choose Cancel and then Yes
TIP RSLogix 5000 software revision 100 or later lets you update controller firmware as part of the download sequence To update the controller download your project and follow the prompts of the software
IMPORTANT If the Revision list is empty download a new upgrade kit Some older upgrade kits do not work with new controllers
weight 1794-L33 71 kg (156 lbs oz)1794-L34 75 g (166 lbs)(no communication cards installed)
28 kg (62 lbs)
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 27
power supply 1794-PS3 or 1794-PS13 ndash In applications that must be compliant with CSA requirements use a Separated Extra-Low Voltage (SELV) power supply that is compliant with IEC 610101 Annex H
power conductors 60deg C (140deg F) minimum copper22 to 14 AWG (0324 to 208 sq mm) stranded364 inch (12mm) insulation maximumlength 10m or less
category 3(2)
power connector torque 5 to 7 inch-pounds (06 to 08Nm)
battery 1756-BA1 (AB part number 94194801)059g lithium
na
serial cable 1761-CBLPM02 to 1761-NET-AIC 1761-CBLPA00 to 1761-NET-AIC1756-CP3 directly to controller1747-CP3 directly to controller
DIN rail steel 35 x 755mm DIN railA-B part number 199-DR1 46277-3 EN 50022
operating temperature IEC 60068-2-1 (Test Ad Operating Cold)IEC 60068-2-2 (Test Bd Operating Dry Heat)IEC 60068-2-14 (Test Nb Operating Thermal Shock)0 to 60degC (32 to 140degF)
storage temperature IEC 60068-2-1 (Test Ab Un-packaged Non-operating Cold)IEC 60068-2-2 (Test Bb Un-packaged Non-operating Dry Heat)IEC 60068-2-14 (Test Na Un-packaged Non-operating Thermal Shock)ndash40 to 85degC (ndash40 to 185degF)
relative humidity IEC 60068-2-30 (Test Db Un-packaged Non-operating Damp Heat)5 to 95 non-condensing
vibration(3) IEC60068-2-6 (Test Fc Operating) 5g 10-500Hz
shock(3)
operatingnon-operating
IEC60068-2-27 (Test Ea Unpackaged shock)
30g50g
emissions CISPR 11Group 1 Class A (with appropriate enclosure)
ESD immunity IEC 61000-4-26kV contact discharges8kV air discharges
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
RA-QR005C-EN-E 608
FlexLogix Controller System 3
Environment and Enclosure
Prevent Electrostatic Discharge
ATTENTION This equipment is intended for use in a Pollution Degree 2 industrial environment in overvoltage Category II applications (as defined in IEC publication 60664-1) at altitudes up to 2000 meters without derating
This equipment is considered Group 1 Class A industrial equipment according to IECCISPR Publication 11 Without appropriate precautions there may be potential difficulties ensuring electromagnetic compatibility in other environments due to conducted as well as radiated disturbance
This equipment is supplied as open type equipment It must be mounted within an enclosure that is suitably designed for those specific environmental conditions that will be present and appropriately designed to prevent personal injury resulting from accessibility to live parts The interior of the enclosure must be accessible only by the use of a tool Subsequent sections of this publication may contain additional information regarding specific enclosure type ratings that are required to comply with certain product safety certifications
NOTE See NEMA Standards publication 250 and IEC publication 60529 as applicable for explanations of the degrees of protection provided by different types of enclosure Also see the appropriate sections in this publication as well as the Allen-Bradley publication 1770-41 (Industrial Automation Wiring and Grounding Guidelines) for additional installation requirements pertaining to this equipment
ATTENTION This equipment is sensitive to electrostatic discharge which can cause internal damage and affect normal operation Follow these guidelines when you handle this equipment
bull Touch a grounded object to discharge potential static
bull Wear an approved grounding wriststrap
bull Do not touch connectors or pins on component boards
bull Do not touch circuit components inside the equipment
bull If available use a static-safe workstation
bull When not in use store the equipment in appropriate static-safe packaging
Publication 1794-IN002G-EN-P - January 2004
4 FlexLogix Controller System
European Hazardous Location Approval
European Zone 2 Certification (The following applies when the product bears the EEx Marking)
This equipment is intended for use in potentially explosive atmospheres as defined by European Union Directive 949EC
The LCIE (Laboratoire Central des Industries Electriques) certifies that this equipment has been found to comply with the Essential Health and Safety Requirements relating to the design and construction of Category 3 equipment intended for use in potentially explosive atmospheres given in Annex II to this Directive The examination and test results are recorded in confidential report No 28 682 010
Compliance with the Essential Health and Safety Requirements has been assured by compliance with EN 50021
IMPORTANT When using this product also consider the following
bull This equipment is not resistant to sunlight or other sources of UV radiation
bull The secondary of a current transformer shall not be open-circuited when applied in Class I Zone 2 environments
bull Equipment of lesser Enclosure Type Rating must be installed in an enclosure providing at least IP54 protection when applied in Class I Zone 2 environments
bull This equipment shall be used within its specified ratings defined by Allen-Bradley
bull Provision shall be made to prevent the rated voltage from being exceeded by transient disturbances of more than 40 when applied in Class I Zone 2 environments
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 5
North American Hazardous Location ApprovalThe following information applies when operating this equipment in hazardous locations
Informations sur lrsquoutilisation de cet eacutequipement en environnements dangereux
Products marked ldquoCL I DIV 2 GP A B C Drdquo are suitable for use in Class I Division 2 Groups A B C D Hazardous Locations and nonhazardous locations only Each product is supplied with markings on the rating nameplate indicating the hazardous location temperature code When combining products within a system the most adverse temperature code (lowest ldquoTrdquo number) may be used to help determine the overall temperature code of the system Combinations of equipment in your system are subject to investigation by the local Authority Having Jurisdiction at the time of installation
Les produits marqueacutes CL I DIV 2 GP A B C D ne conviennent qursquoagrave une utilisation en environnements de Classe I Division 2 Groupes A B C D dangereux et non dangereux Chaque produit est livreacute avec des marquages sur sa plaque drsquoidentification qui indiquent le code de tempeacuterature pour les environnements dangereux Lorsque plusieurs produits sont combineacutes dans un systegraveme le code de tempeacuterature le plus deacutefavorable (code de tempeacuterature le plus faible) peut ecirctre utiliseacute pour deacuteterminer le code de tempeacuterature global du systegraveme Les combinaisons drsquoeacutequipements dans le systegraveme sont sujettes agrave inspection par les autoriteacutes locales qualifieacutees au moment de lrsquoinstallation
Publication 1794-IN002G-EN-P - January 2004
6 FlexLogix Controller System
WARNING EXPLOSION HAZARD
bull Do not disconnect equipment unless power has been removed or the area is known to be nonhazardous
bull Do not disconnect connections to this equipment unless power has been removed or the area is known to be nonhazardous Secure any external connections that mate to this equipment by using screws sliding latches threaded connectors or other means provided with this product
bull Substitution of components may impair suitability for Class I Division 2
bull If this product contains batteries they must only be changed in an area known to be nonhazardous
AVERTISSEMENT RISQUE DrsquoEXPLOSION
bull Couper le courant ou srsquoassurer que lrsquoenvironnement est classeacute non dangereux avant de deacutebrancher leacutequipement
bull Couper le courant ou sassurer que lrsquoenvironnement est classeacute non dangereux avant de deacutebrancher les connecteurs Fixer tous les connecteurs externes relieacutes agrave cet eacutequipement agrave laide de vis loquets coulissants connecteurs fileteacutes ou autres moyens fournis avec ce produit
bull La substitution de composants peut rendre cet eacutequipement inadapteacute agrave une utilisation en environnement de Classe I Division 2
bull Srsquoassurer que lrsquoenvironnement est classeacute non dangereux avant de changer les piles
The following information applies when operating this equipment in hazardous locations
Informations sur lrsquoutilisation de cet eacutequipement en environnements dangereux
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 7
Removal and Insertion Under PowerThe FlexLogix controller the extended-local IO adapter the communication daughtercards and the IO terminal bases cannot be removed or inserted under power
However you can remove and insert FLEX IO modules while backplane power is applied and the system is operating
Be sure that power is removed or the area is nonhazardous before proceeding
Other Considerations
WARNING If you insert or remove the module while backplane power is on an electrical arc can occur This could cause an explosion in hazardous location installations
ATTENTION Also consider the following before you install your FlexLogix controller
bull This product is grounded through the DIN rail to chassis ground Use zinc plated yellow-chromate steel DIN rail to assure proper grounding The use of other DIN rail materials (eg aluminum plastic etc) that can corrode oxidize or are poor conductors can result in improper or intermittent grounding
bull Power connection length should be less than 10 meters
Publication 1794-IN002G-EN-P - January 2004
8 FlexLogix Controller System
What You Need to DoBefore you can install a FlexLogix controller or extended-local adapter you must
Install steel 35 x 755mm DIN rails (A-B part number 199-DR1 46277-3) where you want to place the FlexLogix system components
The DIN rails for all FlexLogix system components including all local and extended-local IO modules must be mounted on a common conductive surface to ensure proper electromagnetic interference (EMI) performance See 24 and 25 for approximate mounting dimensions and mounting clearances
For more information about mounting DIN rails and splitting IO across DIN rails see the FLEX IO Product Data publication 1794-21
Use DIN rail locks (A-B catalog number 1492-EA35) to meet the shock and vibrations specifications listed on 26 A pair of DIN locks comes with the controller
Mount an appropriate power supply on an appropriate DIN rail See the specifications on 26
To install a FlexLogix controller
Step 1 Verify That You Have All the Components see page 9
Step 2 Install the Battery see page 10
Step 3 Install Communication Daughtercards (optional) see page 11
Step 4 Install the Controller see page 12
Step 5 Install the Extended-Local Adapter (optional) see page 15
After you install the FlexLogix controller you can
Make an RS-232 Connection to the Controller see page 18
Select the Operating Mode of the Controller see page 21
Monitor the Controller LEDs see page 22
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 9
Step 1 Verify That You Have All the ComponentsThese components ship with the FlexLogix controller
bull 1756-BA1 battery and label
bull key
bull one spring-clip connector plug for 24V power connection
bull one screw-terminal connector plug for 24V power connection
bull two 1492-EA35 DIN rail locks
The system components you have depend on your application You might have
FlexLogix System Component Description
1788-CNC -CNCR for ControlNet communications1788-CNF -CNFR for ControlNet communications1788-DNBO for DeviceNet communications1788-ENBT for EtherNetIP communications
1756-CP3You can also use the 1747-CP3 cable from the SLC product family
1794-FLA
1794-CE1 (1 foot)1794-CE3 (3 foot)
communication card
serial cable
FlexLogix extended-local adapter
extended- local IO cable
Publication 1794-IN002G-EN-P - January 2004
10 FlexLogix Controller System
Step 2 Install the Battery
For Safety information on the handling of lithium batteries including handling and disposal of leaking batteries see Guidelines for Handling Lithium Batteries publication AG 5-4
1 Install a 1756-BA1 battery
2 Attach the battery label
a Write on the battery label the date you install the battery
b Attach the label to the inside of the battery compartment
ATTENTION Only install a 1756-BA1 battery If you install a different battery you may damage the controller
WARNING For safety information on the handling of lithium batteries in-cluding the handling and disposal of leaking batteries see Guide-lines for Handling Lithium Batteries publication AG-54Store batteries in a cool dry environment We recommend 25degC with 40 to 60 relative humidity You may store batteries for up to 30 days between -45deg to 85degC such as during transporta-tion To avoid possible leakage do not store batteries above 60degC for more than 30 days
When you connect or disconnect the battery an electrical arc can occur This could cause an explosion in hazardous location in-stallations Be sure that power is removed or the area is nonhaz-ardous before proceeding
Attach battery here
top red lead (+)
middle black lead (-)
bottom no connection
Attach label here
This jumper is for service use only Do not use this jumper
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 11
Step 3 Install Communication Daughtercards (optional)
For specific information about configuring the communication card (such as setting a node address) see the installation instructions for the communication card
1 Turn off power to the controller
2 If necessary remove the blank cover from the communication slot
3 Slide the communication card into the communication slot Be sure to line up the card with the card guides in the controller
4 Record which slot you use for the communication card You need the slot number when you develop your controller application
5 Secure the card with the screws to ensure proper grounding Do not over-tighten the screws The maximum torque for the card screws is 48 to 52 inch pounds (05 to 06 Nm)
6 After the controller is installed (see page 12) connect the network cable
Removing a Communication CardIf you need to remove a communication card from the controller
1 Turn off power to the controller
2 Disconnect all cables from the communication card
3 Loosen the card screws from the communication card
4 Remove the card from the controller
5 Replace the card with a blank cover or a different communication card
WARNING If you insert or remove the card while host power is on an electrical arc can occur This could cause an explosion in haz-ardous location installations
31032-M
slot 1slot 2
Publication 1794-IN002G-EN-P - January 2004
12 FlexLogix Controller System
Step 4 Install the Controller
1 Position the FlexLogix controller on the DIN rail at a 5deg angle and rotate the controller onto the DIN rail
2 Press the controller down onto the DIN rail until flush The locking tabs will snap into position and lock the controller onto the DIN rail
If the controller does not lock in place use a screwdriver or similar device to move the locking tabs down while pressing the controller onto the DIN rail Release the locking tabs to lock the controller in place If necessary push up on the locking tabs to lock
3 Ground the controller The DIN rail and the common conductive surface behind the DIN rail provide functional ground for the controller Use the grounding stud to meet safety ground requirements
For information about wiring and grounding see the Industrial Automation Wiring and Grounding Guidelines publication 1770-41
IMPORTANT You can mount the FlexLogix controller either vertically or horizontally (as shown)
A
A
locking tabs
grounding stud
Equipment grounding conductor (ground lug with 208 sq mm [14 AWG] wire) to ground bus
nuts with captive star washer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 13
4 Make sure power is not applied to the power supply
5 Connect the power supply to the controller The graphic below and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the top of the controller connector terminal A to the bottom left power connector terminal G
b Connect -24V common to top controller connector terminal B to the top left power connector terminal E
c Use connections C and D on the controller and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the controller to meet the requirements for installations in Class I Division 2 locations
WARNING If you connect or disconnect wiring while the field-side power is on an electrical arc can occur This could cause an explosion in hazardous location installations Be sure that power is re-moved or the area is nonhazardous before proceeding
+
+
A
B
C
D
FE
HG
_
_
Publication 1794-IN002G-EN-P - January 2004
14 FlexLogix Controller System
6 Mount the IO terminal bases on the DIN rail
For information about IO terminal bases see the FLEX IO Terminal Base Installation Instructions publication 1794-IN092
7 Install the IO modules
To install an IO module see the installation instructions for that module
Removing the controllerIf you need to remove the controller follow these steps
1 Turn off power to the controller
2 Disconnect all cables from the controller
3 Remove the IO module that is adjacent to the controller
4 On the terminal base adjacent to the controller slide the FLEXBUS connector away from the controller and remove the IO terminal base
5 Remove the controller from the DIN rail
B
A
A
31036-M
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 15
Step 5 Install the Extended-Local Adapter (optional)
1 Position the 1794-FLA extended-local IO adapter on the DIN rail at a 30deg angle and rotate the adapter onto the DIN rail
2 Press the adapter down onto the DIN rail until flush The locking tab will snap into position and lock the adapter onto the DIN rail
If the adapter does not lock in place use a screwdriver or similar device to move the locking tab down while pressing the adapter onto the DIN rail Release the locking tab to lock the adapter in place If necessary push up on the locking tab to lock
3 Ground the adapter The adapter is grounded through the steel DIN rail and the common conductive surface behind the DIN rail Additionally use the grounding stud
grounding stud
Equipment grounding conductor (ground lug with 208 sq mm [14 AWG] wire) to ground bus
nuts with captive star washer
Publication 1794-IN002G-EN-P - January 2004
16 FlexLogix Controller System
4 Make sure power is not applied to the power supply Connect the power supply to the adapter This diagram and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the left adapter connector terminal A to the bottom left power connector terminal G
b Connect -24V common to left adapter connector terminal B to the top left power connector terminal E
c Use connections C and D on the adapter and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the adapter to meet the requirements for installations in Class I Division 2 locations
5 Connect IO terminal bases and IO modules to the adapter the same way you connect them to the controller
6 Remove the plastic spacer from both ends of the extended-local IO cable (1794-CE1 or 1794-CE3)
plastic spacer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 17
7 Connect the adapter to the controller
The following diagram shows how you can also use the 1794-CE1 -CE3 cable to split a rail of IO You can split each rail only once You can split a rail right after the controller (or adapter) or after any IO module For more information about the 1794-CE1 -CE3 cables see the Interconnect Cable Installation Instructions publication 1794-512
Removing the extended-local adapterIf you need to remove the adapter follow these steps
1 Turn off power to the adapter
2 Disconnect all cables from the adapter
3 Remove the IO module that is adjacent to the adapter
4 On the terminal base adjacent to the adapter slide the FLEXBUS connector away from the adapter and remove the IO terminal base
5 Remove the adapter from the DIN rail
31039-M
1794-CE1 or 1794-CE3 cable
LOCAL rail
LOCAL2 rail
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
Publication 1794-IN002G-EN-P - January 2004
18 FlexLogix Controller System
Make an RS-232 Connection to the ControllerThe RS-232 port is a non-isolated serial port built-in to the front of the controller
To connect to the serial port
1 Determine whether you need an optical isolator
If you connect the controller to a device outside of the systemrsquos enclosure consider installing an isolator between the controller and device
One possible isolator is the 1761-NET-AIC interface converter
serial port
port 1 DB-9 RS-232 DTE
baud rate selector switch
port 2 mini-DIN 8 RS-232
dc power source selector switch
terminals for external 24V dc power supply
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 19
2 Select the appropriate cable
Are you using an isolator
Use this cable
no The 1756-CP3 cable attaches the controller directly to the controller
If you make your own cable it must be shielded and the shields must be tied to the metal shell (that surrounds the pins) on both ends of the cableYou can also use a 1747-CP3 cable (from the SLC product family) This cable has a taller right-angle connector housing than the 1756-CP3 cable
yes The 1761-CBL-AP00 cable (right-angle connector to controller) or the 1761-CBL-PM02 cable (straight connector to the controller) attaches the controller to port 2 on the 1761-NET-AIC isolator The mini-DIN connector is not commercially available so you cannot make this cable
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
DB-9 right-angle or straight cable end 8-pin mini-DIN cable end
Pin DB-9 end Mini-DIN end1 DCD DCD
2 RxD RxD
3 TxD TxD
4 DTR DTR
5 ground ground
6 DSR DSR
7 RTS RTS
8 CTS CTS
9 na na
1 2
34
5
6 7867
8
9
1
2
3
4
5
Publication 1794-IN002G-EN-P - January 2004
20 FlexLogix Controller System
3 Connect the appropriate cable to the serial port on the controller
Be sure that power is removed or the area is nonhazardous before proceeding
4 If necessary attach the controller to the isolator
WARNING If you connect or disconnect the serial cable with power applied to this module or the serial device on the other end of the cable an electrical arc can occur This could cause an explosion in hazardous location installations
modem
1761-NET-AIC isolator
user-supplied modem cable
1761 cable
system enclosure
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 21
Select the Operating Mode of the Controller
1 Use this table to determine the operating mode of the controller
2 Turn the key on the front panel of the controller to select the mode
If you want to Select one of these modes
Run Program Remote
Run Program Test
turn outputs to the state commanded by the logic of the project
YES YES
turn outputs to their configured state for Program mode
YES YES YES
execute (scan) tasks YES YES YES
change the mode of the controller through software
YES YES YES
download a project YES YES
schedule a ControlNet network YES YES
while online edit the project YES YES YES YES
To select Turn the key to
Remote Run RUN and then to REM
Remote Program PROG and then to REM
Remote Test REM and then go online and select Test mode via the programming software
keyswitch
Publication 1794-IN002G-EN-P - January 2004
22 FlexLogix Controller System
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware RevisionTo update the firmware of a controller first install a firmware upgrade kit
bull An upgrade kit ships on a supplemental CD along with RSLogix 5000 software
bull To download an upgrade kit go to httpsupportrockwellautomationcom Choose Firmware Updates
Indicator Color Description
RUN off bull no task(s) running
bull controller in Program mode
green bull one or more tasks are running
bull controller is in Run mode
OK off no power applied
red flashing after initially installing the controller - the controller requires a FLASH upgrade to the proper firmware revision see belowafter the controller is operating - recoverable fault
red bull controller faulted
bull clear faults clear memory or replace the controller
green controller OK
BATTERY off battery will support memory
red bull battery may not support memory
bull replace battery
IO off bull controller project not downloaded (the condition after power up)
bull no IO or communications configured
green communicating to all devices
green flashing one or more devices are not responding
LOCALandLOCAL2
off rail is inhibited
green communicating to all devices on that rail
green flashing one or more devices on that rail not responding
red flashing no modules exist on that rail
RS232 off no activity
green data being received or transmitted
FORCE off no forces present
amber forces present
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 23
Update the Controller
1 Connect the controller to the same network as your workstation
2 Start ControlFLASH software
3 Choose Next gt
4 Select the catalog number of the controller and choose Next gt
5 Expand the network until you see the controller If the required network is not shown first configure a driver for the network in RSLinx software
6 Select the controller and choose OK
7 Select the revision level to which you want to update the controller and choose Next gt
8 To start the update of the controller choose Finish and then Yes
After the controller is updated the status box displays Update complete
9 Choose OK
10 To close ControlFLASH software choose Cancel and then Yes
TIP RSLogix 5000 software revision 100 or later lets you update controller firmware as part of the download sequence To update the controller download your project and follow the prompts of the software
IMPORTANT If the Revision list is empty download a new upgrade kit Some older upgrade kits do not work with new controllers
weight 1794-L33 71 kg (156 lbs oz)1794-L34 75 g (166 lbs)(no communication cards installed)
28 kg (62 lbs)
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 27
power supply 1794-PS3 or 1794-PS13 ndash In applications that must be compliant with CSA requirements use a Separated Extra-Low Voltage (SELV) power supply that is compliant with IEC 610101 Annex H
power conductors 60deg C (140deg F) minimum copper22 to 14 AWG (0324 to 208 sq mm) stranded364 inch (12mm) insulation maximumlength 10m or less
category 3(2)
power connector torque 5 to 7 inch-pounds (06 to 08Nm)
battery 1756-BA1 (AB part number 94194801)059g lithium
na
serial cable 1761-CBLPM02 to 1761-NET-AIC 1761-CBLPA00 to 1761-NET-AIC1756-CP3 directly to controller1747-CP3 directly to controller
DIN rail steel 35 x 755mm DIN railA-B part number 199-DR1 46277-3 EN 50022
operating temperature IEC 60068-2-1 (Test Ad Operating Cold)IEC 60068-2-2 (Test Bd Operating Dry Heat)IEC 60068-2-14 (Test Nb Operating Thermal Shock)0 to 60degC (32 to 140degF)
storage temperature IEC 60068-2-1 (Test Ab Un-packaged Non-operating Cold)IEC 60068-2-2 (Test Bb Un-packaged Non-operating Dry Heat)IEC 60068-2-14 (Test Na Un-packaged Non-operating Thermal Shock)ndash40 to 85degC (ndash40 to 185degF)
relative humidity IEC 60068-2-30 (Test Db Un-packaged Non-operating Damp Heat)5 to 95 non-condensing
vibration(3) IEC60068-2-6 (Test Fc Operating) 5g 10-500Hz
shock(3)
operatingnon-operating
IEC60068-2-27 (Test Ea Unpackaged shock)
30g50g
emissions CISPR 11Group 1 Class A (with appropriate enclosure)
ESD immunity IEC 61000-4-26kV contact discharges8kV air discharges
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
RA-QR005C-EN-E 608
4 FlexLogix Controller System
European Hazardous Location Approval
European Zone 2 Certification (The following applies when the product bears the EEx Marking)
This equipment is intended for use in potentially explosive atmospheres as defined by European Union Directive 949EC
The LCIE (Laboratoire Central des Industries Electriques) certifies that this equipment has been found to comply with the Essential Health and Safety Requirements relating to the design and construction of Category 3 equipment intended for use in potentially explosive atmospheres given in Annex II to this Directive The examination and test results are recorded in confidential report No 28 682 010
Compliance with the Essential Health and Safety Requirements has been assured by compliance with EN 50021
IMPORTANT When using this product also consider the following
bull This equipment is not resistant to sunlight or other sources of UV radiation
bull The secondary of a current transformer shall not be open-circuited when applied in Class I Zone 2 environments
bull Equipment of lesser Enclosure Type Rating must be installed in an enclosure providing at least IP54 protection when applied in Class I Zone 2 environments
bull This equipment shall be used within its specified ratings defined by Allen-Bradley
bull Provision shall be made to prevent the rated voltage from being exceeded by transient disturbances of more than 40 when applied in Class I Zone 2 environments
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 5
North American Hazardous Location ApprovalThe following information applies when operating this equipment in hazardous locations
Informations sur lrsquoutilisation de cet eacutequipement en environnements dangereux
Products marked ldquoCL I DIV 2 GP A B C Drdquo are suitable for use in Class I Division 2 Groups A B C D Hazardous Locations and nonhazardous locations only Each product is supplied with markings on the rating nameplate indicating the hazardous location temperature code When combining products within a system the most adverse temperature code (lowest ldquoTrdquo number) may be used to help determine the overall temperature code of the system Combinations of equipment in your system are subject to investigation by the local Authority Having Jurisdiction at the time of installation
Les produits marqueacutes CL I DIV 2 GP A B C D ne conviennent qursquoagrave une utilisation en environnements de Classe I Division 2 Groupes A B C D dangereux et non dangereux Chaque produit est livreacute avec des marquages sur sa plaque drsquoidentification qui indiquent le code de tempeacuterature pour les environnements dangereux Lorsque plusieurs produits sont combineacutes dans un systegraveme le code de tempeacuterature le plus deacutefavorable (code de tempeacuterature le plus faible) peut ecirctre utiliseacute pour deacuteterminer le code de tempeacuterature global du systegraveme Les combinaisons drsquoeacutequipements dans le systegraveme sont sujettes agrave inspection par les autoriteacutes locales qualifieacutees au moment de lrsquoinstallation
Publication 1794-IN002G-EN-P - January 2004
6 FlexLogix Controller System
WARNING EXPLOSION HAZARD
bull Do not disconnect equipment unless power has been removed or the area is known to be nonhazardous
bull Do not disconnect connections to this equipment unless power has been removed or the area is known to be nonhazardous Secure any external connections that mate to this equipment by using screws sliding latches threaded connectors or other means provided with this product
bull Substitution of components may impair suitability for Class I Division 2
bull If this product contains batteries they must only be changed in an area known to be nonhazardous
AVERTISSEMENT RISQUE DrsquoEXPLOSION
bull Couper le courant ou srsquoassurer que lrsquoenvironnement est classeacute non dangereux avant de deacutebrancher leacutequipement
bull Couper le courant ou sassurer que lrsquoenvironnement est classeacute non dangereux avant de deacutebrancher les connecteurs Fixer tous les connecteurs externes relieacutes agrave cet eacutequipement agrave laide de vis loquets coulissants connecteurs fileteacutes ou autres moyens fournis avec ce produit
bull La substitution de composants peut rendre cet eacutequipement inadapteacute agrave une utilisation en environnement de Classe I Division 2
bull Srsquoassurer que lrsquoenvironnement est classeacute non dangereux avant de changer les piles
The following information applies when operating this equipment in hazardous locations
Informations sur lrsquoutilisation de cet eacutequipement en environnements dangereux
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 7
Removal and Insertion Under PowerThe FlexLogix controller the extended-local IO adapter the communication daughtercards and the IO terminal bases cannot be removed or inserted under power
However you can remove and insert FLEX IO modules while backplane power is applied and the system is operating
Be sure that power is removed or the area is nonhazardous before proceeding
Other Considerations
WARNING If you insert or remove the module while backplane power is on an electrical arc can occur This could cause an explosion in hazardous location installations
ATTENTION Also consider the following before you install your FlexLogix controller
bull This product is grounded through the DIN rail to chassis ground Use zinc plated yellow-chromate steel DIN rail to assure proper grounding The use of other DIN rail materials (eg aluminum plastic etc) that can corrode oxidize or are poor conductors can result in improper or intermittent grounding
bull Power connection length should be less than 10 meters
Publication 1794-IN002G-EN-P - January 2004
8 FlexLogix Controller System
What You Need to DoBefore you can install a FlexLogix controller or extended-local adapter you must
Install steel 35 x 755mm DIN rails (A-B part number 199-DR1 46277-3) where you want to place the FlexLogix system components
The DIN rails for all FlexLogix system components including all local and extended-local IO modules must be mounted on a common conductive surface to ensure proper electromagnetic interference (EMI) performance See 24 and 25 for approximate mounting dimensions and mounting clearances
For more information about mounting DIN rails and splitting IO across DIN rails see the FLEX IO Product Data publication 1794-21
Use DIN rail locks (A-B catalog number 1492-EA35) to meet the shock and vibrations specifications listed on 26 A pair of DIN locks comes with the controller
Mount an appropriate power supply on an appropriate DIN rail See the specifications on 26
To install a FlexLogix controller
Step 1 Verify That You Have All the Components see page 9
Step 2 Install the Battery see page 10
Step 3 Install Communication Daughtercards (optional) see page 11
Step 4 Install the Controller see page 12
Step 5 Install the Extended-Local Adapter (optional) see page 15
After you install the FlexLogix controller you can
Make an RS-232 Connection to the Controller see page 18
Select the Operating Mode of the Controller see page 21
Monitor the Controller LEDs see page 22
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 9
Step 1 Verify That You Have All the ComponentsThese components ship with the FlexLogix controller
bull 1756-BA1 battery and label
bull key
bull one spring-clip connector plug for 24V power connection
bull one screw-terminal connector plug for 24V power connection
bull two 1492-EA35 DIN rail locks
The system components you have depend on your application You might have
FlexLogix System Component Description
1788-CNC -CNCR for ControlNet communications1788-CNF -CNFR for ControlNet communications1788-DNBO for DeviceNet communications1788-ENBT for EtherNetIP communications
1756-CP3You can also use the 1747-CP3 cable from the SLC product family
1794-FLA
1794-CE1 (1 foot)1794-CE3 (3 foot)
communication card
serial cable
FlexLogix extended-local adapter
extended- local IO cable
Publication 1794-IN002G-EN-P - January 2004
10 FlexLogix Controller System
Step 2 Install the Battery
For Safety information on the handling of lithium batteries including handling and disposal of leaking batteries see Guidelines for Handling Lithium Batteries publication AG 5-4
1 Install a 1756-BA1 battery
2 Attach the battery label
a Write on the battery label the date you install the battery
b Attach the label to the inside of the battery compartment
ATTENTION Only install a 1756-BA1 battery If you install a different battery you may damage the controller
WARNING For safety information on the handling of lithium batteries in-cluding the handling and disposal of leaking batteries see Guide-lines for Handling Lithium Batteries publication AG-54Store batteries in a cool dry environment We recommend 25degC with 40 to 60 relative humidity You may store batteries for up to 30 days between -45deg to 85degC such as during transporta-tion To avoid possible leakage do not store batteries above 60degC for more than 30 days
When you connect or disconnect the battery an electrical arc can occur This could cause an explosion in hazardous location in-stallations Be sure that power is removed or the area is nonhaz-ardous before proceeding
Attach battery here
top red lead (+)
middle black lead (-)
bottom no connection
Attach label here
This jumper is for service use only Do not use this jumper
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 11
Step 3 Install Communication Daughtercards (optional)
For specific information about configuring the communication card (such as setting a node address) see the installation instructions for the communication card
1 Turn off power to the controller
2 If necessary remove the blank cover from the communication slot
3 Slide the communication card into the communication slot Be sure to line up the card with the card guides in the controller
4 Record which slot you use for the communication card You need the slot number when you develop your controller application
5 Secure the card with the screws to ensure proper grounding Do not over-tighten the screws The maximum torque for the card screws is 48 to 52 inch pounds (05 to 06 Nm)
6 After the controller is installed (see page 12) connect the network cable
Removing a Communication CardIf you need to remove a communication card from the controller
1 Turn off power to the controller
2 Disconnect all cables from the communication card
3 Loosen the card screws from the communication card
4 Remove the card from the controller
5 Replace the card with a blank cover or a different communication card
WARNING If you insert or remove the card while host power is on an electrical arc can occur This could cause an explosion in haz-ardous location installations
31032-M
slot 1slot 2
Publication 1794-IN002G-EN-P - January 2004
12 FlexLogix Controller System
Step 4 Install the Controller
1 Position the FlexLogix controller on the DIN rail at a 5deg angle and rotate the controller onto the DIN rail
2 Press the controller down onto the DIN rail until flush The locking tabs will snap into position and lock the controller onto the DIN rail
If the controller does not lock in place use a screwdriver or similar device to move the locking tabs down while pressing the controller onto the DIN rail Release the locking tabs to lock the controller in place If necessary push up on the locking tabs to lock
3 Ground the controller The DIN rail and the common conductive surface behind the DIN rail provide functional ground for the controller Use the grounding stud to meet safety ground requirements
For information about wiring and grounding see the Industrial Automation Wiring and Grounding Guidelines publication 1770-41
IMPORTANT You can mount the FlexLogix controller either vertically or horizontally (as shown)
A
A
locking tabs
grounding stud
Equipment grounding conductor (ground lug with 208 sq mm [14 AWG] wire) to ground bus
nuts with captive star washer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 13
4 Make sure power is not applied to the power supply
5 Connect the power supply to the controller The graphic below and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the top of the controller connector terminal A to the bottom left power connector terminal G
b Connect -24V common to top controller connector terminal B to the top left power connector terminal E
c Use connections C and D on the controller and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the controller to meet the requirements for installations in Class I Division 2 locations
WARNING If you connect or disconnect wiring while the field-side power is on an electrical arc can occur This could cause an explosion in hazardous location installations Be sure that power is re-moved or the area is nonhazardous before proceeding
+
+
A
B
C
D
FE
HG
_
_
Publication 1794-IN002G-EN-P - January 2004
14 FlexLogix Controller System
6 Mount the IO terminal bases on the DIN rail
For information about IO terminal bases see the FLEX IO Terminal Base Installation Instructions publication 1794-IN092
7 Install the IO modules
To install an IO module see the installation instructions for that module
Removing the controllerIf you need to remove the controller follow these steps
1 Turn off power to the controller
2 Disconnect all cables from the controller
3 Remove the IO module that is adjacent to the controller
4 On the terminal base adjacent to the controller slide the FLEXBUS connector away from the controller and remove the IO terminal base
5 Remove the controller from the DIN rail
B
A
A
31036-M
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 15
Step 5 Install the Extended-Local Adapter (optional)
1 Position the 1794-FLA extended-local IO adapter on the DIN rail at a 30deg angle and rotate the adapter onto the DIN rail
2 Press the adapter down onto the DIN rail until flush The locking tab will snap into position and lock the adapter onto the DIN rail
If the adapter does not lock in place use a screwdriver or similar device to move the locking tab down while pressing the adapter onto the DIN rail Release the locking tab to lock the adapter in place If necessary push up on the locking tab to lock
3 Ground the adapter The adapter is grounded through the steel DIN rail and the common conductive surface behind the DIN rail Additionally use the grounding stud
grounding stud
Equipment grounding conductor (ground lug with 208 sq mm [14 AWG] wire) to ground bus
nuts with captive star washer
Publication 1794-IN002G-EN-P - January 2004
16 FlexLogix Controller System
4 Make sure power is not applied to the power supply Connect the power supply to the adapter This diagram and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the left adapter connector terminal A to the bottom left power connector terminal G
b Connect -24V common to left adapter connector terminal B to the top left power connector terminal E
c Use connections C and D on the adapter and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the adapter to meet the requirements for installations in Class I Division 2 locations
5 Connect IO terminal bases and IO modules to the adapter the same way you connect them to the controller
6 Remove the plastic spacer from both ends of the extended-local IO cable (1794-CE1 or 1794-CE3)
plastic spacer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 17
7 Connect the adapter to the controller
The following diagram shows how you can also use the 1794-CE1 -CE3 cable to split a rail of IO You can split each rail only once You can split a rail right after the controller (or adapter) or after any IO module For more information about the 1794-CE1 -CE3 cables see the Interconnect Cable Installation Instructions publication 1794-512
Removing the extended-local adapterIf you need to remove the adapter follow these steps
1 Turn off power to the adapter
2 Disconnect all cables from the adapter
3 Remove the IO module that is adjacent to the adapter
4 On the terminal base adjacent to the adapter slide the FLEXBUS connector away from the adapter and remove the IO terminal base
5 Remove the adapter from the DIN rail
31039-M
1794-CE1 or 1794-CE3 cable
LOCAL rail
LOCAL2 rail
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
Publication 1794-IN002G-EN-P - January 2004
18 FlexLogix Controller System
Make an RS-232 Connection to the ControllerThe RS-232 port is a non-isolated serial port built-in to the front of the controller
To connect to the serial port
1 Determine whether you need an optical isolator
If you connect the controller to a device outside of the systemrsquos enclosure consider installing an isolator between the controller and device
One possible isolator is the 1761-NET-AIC interface converter
serial port
port 1 DB-9 RS-232 DTE
baud rate selector switch
port 2 mini-DIN 8 RS-232
dc power source selector switch
terminals for external 24V dc power supply
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 19
2 Select the appropriate cable
Are you using an isolator
Use this cable
no The 1756-CP3 cable attaches the controller directly to the controller
If you make your own cable it must be shielded and the shields must be tied to the metal shell (that surrounds the pins) on both ends of the cableYou can also use a 1747-CP3 cable (from the SLC product family) This cable has a taller right-angle connector housing than the 1756-CP3 cable
yes The 1761-CBL-AP00 cable (right-angle connector to controller) or the 1761-CBL-PM02 cable (straight connector to the controller) attaches the controller to port 2 on the 1761-NET-AIC isolator The mini-DIN connector is not commercially available so you cannot make this cable
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
DB-9 right-angle or straight cable end 8-pin mini-DIN cable end
Pin DB-9 end Mini-DIN end1 DCD DCD
2 RxD RxD
3 TxD TxD
4 DTR DTR
5 ground ground
6 DSR DSR
7 RTS RTS
8 CTS CTS
9 na na
1 2
34
5
6 7867
8
9
1
2
3
4
5
Publication 1794-IN002G-EN-P - January 2004
20 FlexLogix Controller System
3 Connect the appropriate cable to the serial port on the controller
Be sure that power is removed or the area is nonhazardous before proceeding
4 If necessary attach the controller to the isolator
WARNING If you connect or disconnect the serial cable with power applied to this module or the serial device on the other end of the cable an electrical arc can occur This could cause an explosion in hazardous location installations
modem
1761-NET-AIC isolator
user-supplied modem cable
1761 cable
system enclosure
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 21
Select the Operating Mode of the Controller
1 Use this table to determine the operating mode of the controller
2 Turn the key on the front panel of the controller to select the mode
If you want to Select one of these modes
Run Program Remote
Run Program Test
turn outputs to the state commanded by the logic of the project
YES YES
turn outputs to their configured state for Program mode
YES YES YES
execute (scan) tasks YES YES YES
change the mode of the controller through software
YES YES YES
download a project YES YES
schedule a ControlNet network YES YES
while online edit the project YES YES YES YES
To select Turn the key to
Remote Run RUN and then to REM
Remote Program PROG and then to REM
Remote Test REM and then go online and select Test mode via the programming software
keyswitch
Publication 1794-IN002G-EN-P - January 2004
22 FlexLogix Controller System
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware RevisionTo update the firmware of a controller first install a firmware upgrade kit
bull An upgrade kit ships on a supplemental CD along with RSLogix 5000 software
bull To download an upgrade kit go to httpsupportrockwellautomationcom Choose Firmware Updates
Indicator Color Description
RUN off bull no task(s) running
bull controller in Program mode
green bull one or more tasks are running
bull controller is in Run mode
OK off no power applied
red flashing after initially installing the controller - the controller requires a FLASH upgrade to the proper firmware revision see belowafter the controller is operating - recoverable fault
red bull controller faulted
bull clear faults clear memory or replace the controller
green controller OK
BATTERY off battery will support memory
red bull battery may not support memory
bull replace battery
IO off bull controller project not downloaded (the condition after power up)
bull no IO or communications configured
green communicating to all devices
green flashing one or more devices are not responding
LOCALandLOCAL2
off rail is inhibited
green communicating to all devices on that rail
green flashing one or more devices on that rail not responding
red flashing no modules exist on that rail
RS232 off no activity
green data being received or transmitted
FORCE off no forces present
amber forces present
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 23
Update the Controller
1 Connect the controller to the same network as your workstation
2 Start ControlFLASH software
3 Choose Next gt
4 Select the catalog number of the controller and choose Next gt
5 Expand the network until you see the controller If the required network is not shown first configure a driver for the network in RSLinx software
6 Select the controller and choose OK
7 Select the revision level to which you want to update the controller and choose Next gt
8 To start the update of the controller choose Finish and then Yes
After the controller is updated the status box displays Update complete
9 Choose OK
10 To close ControlFLASH software choose Cancel and then Yes
TIP RSLogix 5000 software revision 100 or later lets you update controller firmware as part of the download sequence To update the controller download your project and follow the prompts of the software
IMPORTANT If the Revision list is empty download a new upgrade kit Some older upgrade kits do not work with new controllers
weight 1794-L33 71 kg (156 lbs oz)1794-L34 75 g (166 lbs)(no communication cards installed)
28 kg (62 lbs)
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 27
power supply 1794-PS3 or 1794-PS13 ndash In applications that must be compliant with CSA requirements use a Separated Extra-Low Voltage (SELV) power supply that is compliant with IEC 610101 Annex H
power conductors 60deg C (140deg F) minimum copper22 to 14 AWG (0324 to 208 sq mm) stranded364 inch (12mm) insulation maximumlength 10m or less
category 3(2)
power connector torque 5 to 7 inch-pounds (06 to 08Nm)
battery 1756-BA1 (AB part number 94194801)059g lithium
na
serial cable 1761-CBLPM02 to 1761-NET-AIC 1761-CBLPA00 to 1761-NET-AIC1756-CP3 directly to controller1747-CP3 directly to controller
DIN rail steel 35 x 755mm DIN railA-B part number 199-DR1 46277-3 EN 50022
operating temperature IEC 60068-2-1 (Test Ad Operating Cold)IEC 60068-2-2 (Test Bd Operating Dry Heat)IEC 60068-2-14 (Test Nb Operating Thermal Shock)0 to 60degC (32 to 140degF)
storage temperature IEC 60068-2-1 (Test Ab Un-packaged Non-operating Cold)IEC 60068-2-2 (Test Bb Un-packaged Non-operating Dry Heat)IEC 60068-2-14 (Test Na Un-packaged Non-operating Thermal Shock)ndash40 to 85degC (ndash40 to 185degF)
relative humidity IEC 60068-2-30 (Test Db Un-packaged Non-operating Damp Heat)5 to 95 non-condensing
vibration(3) IEC60068-2-6 (Test Fc Operating) 5g 10-500Hz
shock(3)
operatingnon-operating
IEC60068-2-27 (Test Ea Unpackaged shock)
30g50g
emissions CISPR 11Group 1 Class A (with appropriate enclosure)
ESD immunity IEC 61000-4-26kV contact discharges8kV air discharges
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
RA-QR005C-EN-E 608
FlexLogix Controller System 5
North American Hazardous Location ApprovalThe following information applies when operating this equipment in hazardous locations
Informations sur lrsquoutilisation de cet eacutequipement en environnements dangereux
Products marked ldquoCL I DIV 2 GP A B C Drdquo are suitable for use in Class I Division 2 Groups A B C D Hazardous Locations and nonhazardous locations only Each product is supplied with markings on the rating nameplate indicating the hazardous location temperature code When combining products within a system the most adverse temperature code (lowest ldquoTrdquo number) may be used to help determine the overall temperature code of the system Combinations of equipment in your system are subject to investigation by the local Authority Having Jurisdiction at the time of installation
Les produits marqueacutes CL I DIV 2 GP A B C D ne conviennent qursquoagrave une utilisation en environnements de Classe I Division 2 Groupes A B C D dangereux et non dangereux Chaque produit est livreacute avec des marquages sur sa plaque drsquoidentification qui indiquent le code de tempeacuterature pour les environnements dangereux Lorsque plusieurs produits sont combineacutes dans un systegraveme le code de tempeacuterature le plus deacutefavorable (code de tempeacuterature le plus faible) peut ecirctre utiliseacute pour deacuteterminer le code de tempeacuterature global du systegraveme Les combinaisons drsquoeacutequipements dans le systegraveme sont sujettes agrave inspection par les autoriteacutes locales qualifieacutees au moment de lrsquoinstallation
Publication 1794-IN002G-EN-P - January 2004
6 FlexLogix Controller System
WARNING EXPLOSION HAZARD
bull Do not disconnect equipment unless power has been removed or the area is known to be nonhazardous
bull Do not disconnect connections to this equipment unless power has been removed or the area is known to be nonhazardous Secure any external connections that mate to this equipment by using screws sliding latches threaded connectors or other means provided with this product
bull Substitution of components may impair suitability for Class I Division 2
bull If this product contains batteries they must only be changed in an area known to be nonhazardous
AVERTISSEMENT RISQUE DrsquoEXPLOSION
bull Couper le courant ou srsquoassurer que lrsquoenvironnement est classeacute non dangereux avant de deacutebrancher leacutequipement
bull Couper le courant ou sassurer que lrsquoenvironnement est classeacute non dangereux avant de deacutebrancher les connecteurs Fixer tous les connecteurs externes relieacutes agrave cet eacutequipement agrave laide de vis loquets coulissants connecteurs fileteacutes ou autres moyens fournis avec ce produit
bull La substitution de composants peut rendre cet eacutequipement inadapteacute agrave une utilisation en environnement de Classe I Division 2
bull Srsquoassurer que lrsquoenvironnement est classeacute non dangereux avant de changer les piles
The following information applies when operating this equipment in hazardous locations
Informations sur lrsquoutilisation de cet eacutequipement en environnements dangereux
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 7
Removal and Insertion Under PowerThe FlexLogix controller the extended-local IO adapter the communication daughtercards and the IO terminal bases cannot be removed or inserted under power
However you can remove and insert FLEX IO modules while backplane power is applied and the system is operating
Be sure that power is removed or the area is nonhazardous before proceeding
Other Considerations
WARNING If you insert or remove the module while backplane power is on an electrical arc can occur This could cause an explosion in hazardous location installations
ATTENTION Also consider the following before you install your FlexLogix controller
bull This product is grounded through the DIN rail to chassis ground Use zinc plated yellow-chromate steel DIN rail to assure proper grounding The use of other DIN rail materials (eg aluminum plastic etc) that can corrode oxidize or are poor conductors can result in improper or intermittent grounding
bull Power connection length should be less than 10 meters
Publication 1794-IN002G-EN-P - January 2004
8 FlexLogix Controller System
What You Need to DoBefore you can install a FlexLogix controller or extended-local adapter you must
Install steel 35 x 755mm DIN rails (A-B part number 199-DR1 46277-3) where you want to place the FlexLogix system components
The DIN rails for all FlexLogix system components including all local and extended-local IO modules must be mounted on a common conductive surface to ensure proper electromagnetic interference (EMI) performance See 24 and 25 for approximate mounting dimensions and mounting clearances
For more information about mounting DIN rails and splitting IO across DIN rails see the FLEX IO Product Data publication 1794-21
Use DIN rail locks (A-B catalog number 1492-EA35) to meet the shock and vibrations specifications listed on 26 A pair of DIN locks comes with the controller
Mount an appropriate power supply on an appropriate DIN rail See the specifications on 26
To install a FlexLogix controller
Step 1 Verify That You Have All the Components see page 9
Step 2 Install the Battery see page 10
Step 3 Install Communication Daughtercards (optional) see page 11
Step 4 Install the Controller see page 12
Step 5 Install the Extended-Local Adapter (optional) see page 15
After you install the FlexLogix controller you can
Make an RS-232 Connection to the Controller see page 18
Select the Operating Mode of the Controller see page 21
Monitor the Controller LEDs see page 22
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 9
Step 1 Verify That You Have All the ComponentsThese components ship with the FlexLogix controller
bull 1756-BA1 battery and label
bull key
bull one spring-clip connector plug for 24V power connection
bull one screw-terminal connector plug for 24V power connection
bull two 1492-EA35 DIN rail locks
The system components you have depend on your application You might have
FlexLogix System Component Description
1788-CNC -CNCR for ControlNet communications1788-CNF -CNFR for ControlNet communications1788-DNBO for DeviceNet communications1788-ENBT for EtherNetIP communications
1756-CP3You can also use the 1747-CP3 cable from the SLC product family
1794-FLA
1794-CE1 (1 foot)1794-CE3 (3 foot)
communication card
serial cable
FlexLogix extended-local adapter
extended- local IO cable
Publication 1794-IN002G-EN-P - January 2004
10 FlexLogix Controller System
Step 2 Install the Battery
For Safety information on the handling of lithium batteries including handling and disposal of leaking batteries see Guidelines for Handling Lithium Batteries publication AG 5-4
1 Install a 1756-BA1 battery
2 Attach the battery label
a Write on the battery label the date you install the battery
b Attach the label to the inside of the battery compartment
ATTENTION Only install a 1756-BA1 battery If you install a different battery you may damage the controller
WARNING For safety information on the handling of lithium batteries in-cluding the handling and disposal of leaking batteries see Guide-lines for Handling Lithium Batteries publication AG-54Store batteries in a cool dry environment We recommend 25degC with 40 to 60 relative humidity You may store batteries for up to 30 days between -45deg to 85degC such as during transporta-tion To avoid possible leakage do not store batteries above 60degC for more than 30 days
When you connect or disconnect the battery an electrical arc can occur This could cause an explosion in hazardous location in-stallations Be sure that power is removed or the area is nonhaz-ardous before proceeding
Attach battery here
top red lead (+)
middle black lead (-)
bottom no connection
Attach label here
This jumper is for service use only Do not use this jumper
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 11
Step 3 Install Communication Daughtercards (optional)
For specific information about configuring the communication card (such as setting a node address) see the installation instructions for the communication card
1 Turn off power to the controller
2 If necessary remove the blank cover from the communication slot
3 Slide the communication card into the communication slot Be sure to line up the card with the card guides in the controller
4 Record which slot you use for the communication card You need the slot number when you develop your controller application
5 Secure the card with the screws to ensure proper grounding Do not over-tighten the screws The maximum torque for the card screws is 48 to 52 inch pounds (05 to 06 Nm)
6 After the controller is installed (see page 12) connect the network cable
Removing a Communication CardIf you need to remove a communication card from the controller
1 Turn off power to the controller
2 Disconnect all cables from the communication card
3 Loosen the card screws from the communication card
4 Remove the card from the controller
5 Replace the card with a blank cover or a different communication card
WARNING If you insert or remove the card while host power is on an electrical arc can occur This could cause an explosion in haz-ardous location installations
31032-M
slot 1slot 2
Publication 1794-IN002G-EN-P - January 2004
12 FlexLogix Controller System
Step 4 Install the Controller
1 Position the FlexLogix controller on the DIN rail at a 5deg angle and rotate the controller onto the DIN rail
2 Press the controller down onto the DIN rail until flush The locking tabs will snap into position and lock the controller onto the DIN rail
If the controller does not lock in place use a screwdriver or similar device to move the locking tabs down while pressing the controller onto the DIN rail Release the locking tabs to lock the controller in place If necessary push up on the locking tabs to lock
3 Ground the controller The DIN rail and the common conductive surface behind the DIN rail provide functional ground for the controller Use the grounding stud to meet safety ground requirements
For information about wiring and grounding see the Industrial Automation Wiring and Grounding Guidelines publication 1770-41
IMPORTANT You can mount the FlexLogix controller either vertically or horizontally (as shown)
A
A
locking tabs
grounding stud
Equipment grounding conductor (ground lug with 208 sq mm [14 AWG] wire) to ground bus
nuts with captive star washer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 13
4 Make sure power is not applied to the power supply
5 Connect the power supply to the controller The graphic below and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the top of the controller connector terminal A to the bottom left power connector terminal G
b Connect -24V common to top controller connector terminal B to the top left power connector terminal E
c Use connections C and D on the controller and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the controller to meet the requirements for installations in Class I Division 2 locations
WARNING If you connect or disconnect wiring while the field-side power is on an electrical arc can occur This could cause an explosion in hazardous location installations Be sure that power is re-moved or the area is nonhazardous before proceeding
+
+
A
B
C
D
FE
HG
_
_
Publication 1794-IN002G-EN-P - January 2004
14 FlexLogix Controller System
6 Mount the IO terminal bases on the DIN rail
For information about IO terminal bases see the FLEX IO Terminal Base Installation Instructions publication 1794-IN092
7 Install the IO modules
To install an IO module see the installation instructions for that module
Removing the controllerIf you need to remove the controller follow these steps
1 Turn off power to the controller
2 Disconnect all cables from the controller
3 Remove the IO module that is adjacent to the controller
4 On the terminal base adjacent to the controller slide the FLEXBUS connector away from the controller and remove the IO terminal base
5 Remove the controller from the DIN rail
B
A
A
31036-M
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 15
Step 5 Install the Extended-Local Adapter (optional)
1 Position the 1794-FLA extended-local IO adapter on the DIN rail at a 30deg angle and rotate the adapter onto the DIN rail
2 Press the adapter down onto the DIN rail until flush The locking tab will snap into position and lock the adapter onto the DIN rail
If the adapter does not lock in place use a screwdriver or similar device to move the locking tab down while pressing the adapter onto the DIN rail Release the locking tab to lock the adapter in place If necessary push up on the locking tab to lock
3 Ground the adapter The adapter is grounded through the steel DIN rail and the common conductive surface behind the DIN rail Additionally use the grounding stud
grounding stud
Equipment grounding conductor (ground lug with 208 sq mm [14 AWG] wire) to ground bus
nuts with captive star washer
Publication 1794-IN002G-EN-P - January 2004
16 FlexLogix Controller System
4 Make sure power is not applied to the power supply Connect the power supply to the adapter This diagram and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the left adapter connector terminal A to the bottom left power connector terminal G
b Connect -24V common to left adapter connector terminal B to the top left power connector terminal E
c Use connections C and D on the adapter and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the adapter to meet the requirements for installations in Class I Division 2 locations
5 Connect IO terminal bases and IO modules to the adapter the same way you connect them to the controller
6 Remove the plastic spacer from both ends of the extended-local IO cable (1794-CE1 or 1794-CE3)
plastic spacer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 17
7 Connect the adapter to the controller
The following diagram shows how you can also use the 1794-CE1 -CE3 cable to split a rail of IO You can split each rail only once You can split a rail right after the controller (or adapter) or after any IO module For more information about the 1794-CE1 -CE3 cables see the Interconnect Cable Installation Instructions publication 1794-512
Removing the extended-local adapterIf you need to remove the adapter follow these steps
1 Turn off power to the adapter
2 Disconnect all cables from the adapter
3 Remove the IO module that is adjacent to the adapter
4 On the terminal base adjacent to the adapter slide the FLEXBUS connector away from the adapter and remove the IO terminal base
5 Remove the adapter from the DIN rail
31039-M
1794-CE1 or 1794-CE3 cable
LOCAL rail
LOCAL2 rail
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
Publication 1794-IN002G-EN-P - January 2004
18 FlexLogix Controller System
Make an RS-232 Connection to the ControllerThe RS-232 port is a non-isolated serial port built-in to the front of the controller
To connect to the serial port
1 Determine whether you need an optical isolator
If you connect the controller to a device outside of the systemrsquos enclosure consider installing an isolator between the controller and device
One possible isolator is the 1761-NET-AIC interface converter
serial port
port 1 DB-9 RS-232 DTE
baud rate selector switch
port 2 mini-DIN 8 RS-232
dc power source selector switch
terminals for external 24V dc power supply
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 19
2 Select the appropriate cable
Are you using an isolator
Use this cable
no The 1756-CP3 cable attaches the controller directly to the controller
If you make your own cable it must be shielded and the shields must be tied to the metal shell (that surrounds the pins) on both ends of the cableYou can also use a 1747-CP3 cable (from the SLC product family) This cable has a taller right-angle connector housing than the 1756-CP3 cable
yes The 1761-CBL-AP00 cable (right-angle connector to controller) or the 1761-CBL-PM02 cable (straight connector to the controller) attaches the controller to port 2 on the 1761-NET-AIC isolator The mini-DIN connector is not commercially available so you cannot make this cable
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
DB-9 right-angle or straight cable end 8-pin mini-DIN cable end
Pin DB-9 end Mini-DIN end1 DCD DCD
2 RxD RxD
3 TxD TxD
4 DTR DTR
5 ground ground
6 DSR DSR
7 RTS RTS
8 CTS CTS
9 na na
1 2
34
5
6 7867
8
9
1
2
3
4
5
Publication 1794-IN002G-EN-P - January 2004
20 FlexLogix Controller System
3 Connect the appropriate cable to the serial port on the controller
Be sure that power is removed or the area is nonhazardous before proceeding
4 If necessary attach the controller to the isolator
WARNING If you connect or disconnect the serial cable with power applied to this module or the serial device on the other end of the cable an electrical arc can occur This could cause an explosion in hazardous location installations
modem
1761-NET-AIC isolator
user-supplied modem cable
1761 cable
system enclosure
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 21
Select the Operating Mode of the Controller
1 Use this table to determine the operating mode of the controller
2 Turn the key on the front panel of the controller to select the mode
If you want to Select one of these modes
Run Program Remote
Run Program Test
turn outputs to the state commanded by the logic of the project
YES YES
turn outputs to their configured state for Program mode
YES YES YES
execute (scan) tasks YES YES YES
change the mode of the controller through software
YES YES YES
download a project YES YES
schedule a ControlNet network YES YES
while online edit the project YES YES YES YES
To select Turn the key to
Remote Run RUN and then to REM
Remote Program PROG and then to REM
Remote Test REM and then go online and select Test mode via the programming software
keyswitch
Publication 1794-IN002G-EN-P - January 2004
22 FlexLogix Controller System
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware RevisionTo update the firmware of a controller first install a firmware upgrade kit
bull An upgrade kit ships on a supplemental CD along with RSLogix 5000 software
bull To download an upgrade kit go to httpsupportrockwellautomationcom Choose Firmware Updates
Indicator Color Description
RUN off bull no task(s) running
bull controller in Program mode
green bull one or more tasks are running
bull controller is in Run mode
OK off no power applied
red flashing after initially installing the controller - the controller requires a FLASH upgrade to the proper firmware revision see belowafter the controller is operating - recoverable fault
red bull controller faulted
bull clear faults clear memory or replace the controller
green controller OK
BATTERY off battery will support memory
red bull battery may not support memory
bull replace battery
IO off bull controller project not downloaded (the condition after power up)
bull no IO or communications configured
green communicating to all devices
green flashing one or more devices are not responding
LOCALandLOCAL2
off rail is inhibited
green communicating to all devices on that rail
green flashing one or more devices on that rail not responding
red flashing no modules exist on that rail
RS232 off no activity
green data being received or transmitted
FORCE off no forces present
amber forces present
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 23
Update the Controller
1 Connect the controller to the same network as your workstation
2 Start ControlFLASH software
3 Choose Next gt
4 Select the catalog number of the controller and choose Next gt
5 Expand the network until you see the controller If the required network is not shown first configure a driver for the network in RSLinx software
6 Select the controller and choose OK
7 Select the revision level to which you want to update the controller and choose Next gt
8 To start the update of the controller choose Finish and then Yes
After the controller is updated the status box displays Update complete
9 Choose OK
10 To close ControlFLASH software choose Cancel and then Yes
TIP RSLogix 5000 software revision 100 or later lets you update controller firmware as part of the download sequence To update the controller download your project and follow the prompts of the software
IMPORTANT If the Revision list is empty download a new upgrade kit Some older upgrade kits do not work with new controllers
weight 1794-L33 71 kg (156 lbs oz)1794-L34 75 g (166 lbs)(no communication cards installed)
28 kg (62 lbs)
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 27
power supply 1794-PS3 or 1794-PS13 ndash In applications that must be compliant with CSA requirements use a Separated Extra-Low Voltage (SELV) power supply that is compliant with IEC 610101 Annex H
power conductors 60deg C (140deg F) minimum copper22 to 14 AWG (0324 to 208 sq mm) stranded364 inch (12mm) insulation maximumlength 10m or less
category 3(2)
power connector torque 5 to 7 inch-pounds (06 to 08Nm)
battery 1756-BA1 (AB part number 94194801)059g lithium
na
serial cable 1761-CBLPM02 to 1761-NET-AIC 1761-CBLPA00 to 1761-NET-AIC1756-CP3 directly to controller1747-CP3 directly to controller
DIN rail steel 35 x 755mm DIN railA-B part number 199-DR1 46277-3 EN 50022
operating temperature IEC 60068-2-1 (Test Ad Operating Cold)IEC 60068-2-2 (Test Bd Operating Dry Heat)IEC 60068-2-14 (Test Nb Operating Thermal Shock)0 to 60degC (32 to 140degF)
storage temperature IEC 60068-2-1 (Test Ab Un-packaged Non-operating Cold)IEC 60068-2-2 (Test Bb Un-packaged Non-operating Dry Heat)IEC 60068-2-14 (Test Na Un-packaged Non-operating Thermal Shock)ndash40 to 85degC (ndash40 to 185degF)
relative humidity IEC 60068-2-30 (Test Db Un-packaged Non-operating Damp Heat)5 to 95 non-condensing
vibration(3) IEC60068-2-6 (Test Fc Operating) 5g 10-500Hz
shock(3)
operatingnon-operating
IEC60068-2-27 (Test Ea Unpackaged shock)
30g50g
emissions CISPR 11Group 1 Class A (with appropriate enclosure)
ESD immunity IEC 61000-4-26kV contact discharges8kV air discharges
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
RA-QR005C-EN-E 608
6 FlexLogix Controller System
WARNING EXPLOSION HAZARD
bull Do not disconnect equipment unless power has been removed or the area is known to be nonhazardous
bull Do not disconnect connections to this equipment unless power has been removed or the area is known to be nonhazardous Secure any external connections that mate to this equipment by using screws sliding latches threaded connectors or other means provided with this product
bull Substitution of components may impair suitability for Class I Division 2
bull If this product contains batteries they must only be changed in an area known to be nonhazardous
AVERTISSEMENT RISQUE DrsquoEXPLOSION
bull Couper le courant ou srsquoassurer que lrsquoenvironnement est classeacute non dangereux avant de deacutebrancher leacutequipement
bull Couper le courant ou sassurer que lrsquoenvironnement est classeacute non dangereux avant de deacutebrancher les connecteurs Fixer tous les connecteurs externes relieacutes agrave cet eacutequipement agrave laide de vis loquets coulissants connecteurs fileteacutes ou autres moyens fournis avec ce produit
bull La substitution de composants peut rendre cet eacutequipement inadapteacute agrave une utilisation en environnement de Classe I Division 2
bull Srsquoassurer que lrsquoenvironnement est classeacute non dangereux avant de changer les piles
The following information applies when operating this equipment in hazardous locations
Informations sur lrsquoutilisation de cet eacutequipement en environnements dangereux
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 7
Removal and Insertion Under PowerThe FlexLogix controller the extended-local IO adapter the communication daughtercards and the IO terminal bases cannot be removed or inserted under power
However you can remove and insert FLEX IO modules while backplane power is applied and the system is operating
Be sure that power is removed or the area is nonhazardous before proceeding
Other Considerations
WARNING If you insert or remove the module while backplane power is on an electrical arc can occur This could cause an explosion in hazardous location installations
ATTENTION Also consider the following before you install your FlexLogix controller
bull This product is grounded through the DIN rail to chassis ground Use zinc plated yellow-chromate steel DIN rail to assure proper grounding The use of other DIN rail materials (eg aluminum plastic etc) that can corrode oxidize or are poor conductors can result in improper or intermittent grounding
bull Power connection length should be less than 10 meters
Publication 1794-IN002G-EN-P - January 2004
8 FlexLogix Controller System
What You Need to DoBefore you can install a FlexLogix controller or extended-local adapter you must
Install steel 35 x 755mm DIN rails (A-B part number 199-DR1 46277-3) where you want to place the FlexLogix system components
The DIN rails for all FlexLogix system components including all local and extended-local IO modules must be mounted on a common conductive surface to ensure proper electromagnetic interference (EMI) performance See 24 and 25 for approximate mounting dimensions and mounting clearances
For more information about mounting DIN rails and splitting IO across DIN rails see the FLEX IO Product Data publication 1794-21
Use DIN rail locks (A-B catalog number 1492-EA35) to meet the shock and vibrations specifications listed on 26 A pair of DIN locks comes with the controller
Mount an appropriate power supply on an appropriate DIN rail See the specifications on 26
To install a FlexLogix controller
Step 1 Verify That You Have All the Components see page 9
Step 2 Install the Battery see page 10
Step 3 Install Communication Daughtercards (optional) see page 11
Step 4 Install the Controller see page 12
Step 5 Install the Extended-Local Adapter (optional) see page 15
After you install the FlexLogix controller you can
Make an RS-232 Connection to the Controller see page 18
Select the Operating Mode of the Controller see page 21
Monitor the Controller LEDs see page 22
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 9
Step 1 Verify That You Have All the ComponentsThese components ship with the FlexLogix controller
bull 1756-BA1 battery and label
bull key
bull one spring-clip connector plug for 24V power connection
bull one screw-terminal connector plug for 24V power connection
bull two 1492-EA35 DIN rail locks
The system components you have depend on your application You might have
FlexLogix System Component Description
1788-CNC -CNCR for ControlNet communications1788-CNF -CNFR for ControlNet communications1788-DNBO for DeviceNet communications1788-ENBT for EtherNetIP communications
1756-CP3You can also use the 1747-CP3 cable from the SLC product family
1794-FLA
1794-CE1 (1 foot)1794-CE3 (3 foot)
communication card
serial cable
FlexLogix extended-local adapter
extended- local IO cable
Publication 1794-IN002G-EN-P - January 2004
10 FlexLogix Controller System
Step 2 Install the Battery
For Safety information on the handling of lithium batteries including handling and disposal of leaking batteries see Guidelines for Handling Lithium Batteries publication AG 5-4
1 Install a 1756-BA1 battery
2 Attach the battery label
a Write on the battery label the date you install the battery
b Attach the label to the inside of the battery compartment
ATTENTION Only install a 1756-BA1 battery If you install a different battery you may damage the controller
WARNING For safety information on the handling of lithium batteries in-cluding the handling and disposal of leaking batteries see Guide-lines for Handling Lithium Batteries publication AG-54Store batteries in a cool dry environment We recommend 25degC with 40 to 60 relative humidity You may store batteries for up to 30 days between -45deg to 85degC such as during transporta-tion To avoid possible leakage do not store batteries above 60degC for more than 30 days
When you connect or disconnect the battery an electrical arc can occur This could cause an explosion in hazardous location in-stallations Be sure that power is removed or the area is nonhaz-ardous before proceeding
Attach battery here
top red lead (+)
middle black lead (-)
bottom no connection
Attach label here
This jumper is for service use only Do not use this jumper
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 11
Step 3 Install Communication Daughtercards (optional)
For specific information about configuring the communication card (such as setting a node address) see the installation instructions for the communication card
1 Turn off power to the controller
2 If necessary remove the blank cover from the communication slot
3 Slide the communication card into the communication slot Be sure to line up the card with the card guides in the controller
4 Record which slot you use for the communication card You need the slot number when you develop your controller application
5 Secure the card with the screws to ensure proper grounding Do not over-tighten the screws The maximum torque for the card screws is 48 to 52 inch pounds (05 to 06 Nm)
6 After the controller is installed (see page 12) connect the network cable
Removing a Communication CardIf you need to remove a communication card from the controller
1 Turn off power to the controller
2 Disconnect all cables from the communication card
3 Loosen the card screws from the communication card
4 Remove the card from the controller
5 Replace the card with a blank cover or a different communication card
WARNING If you insert or remove the card while host power is on an electrical arc can occur This could cause an explosion in haz-ardous location installations
31032-M
slot 1slot 2
Publication 1794-IN002G-EN-P - January 2004
12 FlexLogix Controller System
Step 4 Install the Controller
1 Position the FlexLogix controller on the DIN rail at a 5deg angle and rotate the controller onto the DIN rail
2 Press the controller down onto the DIN rail until flush The locking tabs will snap into position and lock the controller onto the DIN rail
If the controller does not lock in place use a screwdriver or similar device to move the locking tabs down while pressing the controller onto the DIN rail Release the locking tabs to lock the controller in place If necessary push up on the locking tabs to lock
3 Ground the controller The DIN rail and the common conductive surface behind the DIN rail provide functional ground for the controller Use the grounding stud to meet safety ground requirements
For information about wiring and grounding see the Industrial Automation Wiring and Grounding Guidelines publication 1770-41
IMPORTANT You can mount the FlexLogix controller either vertically or horizontally (as shown)
A
A
locking tabs
grounding stud
Equipment grounding conductor (ground lug with 208 sq mm [14 AWG] wire) to ground bus
nuts with captive star washer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 13
4 Make sure power is not applied to the power supply
5 Connect the power supply to the controller The graphic below and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the top of the controller connector terminal A to the bottom left power connector terminal G
b Connect -24V common to top controller connector terminal B to the top left power connector terminal E
c Use connections C and D on the controller and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the controller to meet the requirements for installations in Class I Division 2 locations
WARNING If you connect or disconnect wiring while the field-side power is on an electrical arc can occur This could cause an explosion in hazardous location installations Be sure that power is re-moved or the area is nonhazardous before proceeding
+
+
A
B
C
D
FE
HG
_
_
Publication 1794-IN002G-EN-P - January 2004
14 FlexLogix Controller System
6 Mount the IO terminal bases on the DIN rail
For information about IO terminal bases see the FLEX IO Terminal Base Installation Instructions publication 1794-IN092
7 Install the IO modules
To install an IO module see the installation instructions for that module
Removing the controllerIf you need to remove the controller follow these steps
1 Turn off power to the controller
2 Disconnect all cables from the controller
3 Remove the IO module that is adjacent to the controller
4 On the terminal base adjacent to the controller slide the FLEXBUS connector away from the controller and remove the IO terminal base
5 Remove the controller from the DIN rail
B
A
A
31036-M
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 15
Step 5 Install the Extended-Local Adapter (optional)
1 Position the 1794-FLA extended-local IO adapter on the DIN rail at a 30deg angle and rotate the adapter onto the DIN rail
2 Press the adapter down onto the DIN rail until flush The locking tab will snap into position and lock the adapter onto the DIN rail
If the adapter does not lock in place use a screwdriver or similar device to move the locking tab down while pressing the adapter onto the DIN rail Release the locking tab to lock the adapter in place If necessary push up on the locking tab to lock
3 Ground the adapter The adapter is grounded through the steel DIN rail and the common conductive surface behind the DIN rail Additionally use the grounding stud
grounding stud
Equipment grounding conductor (ground lug with 208 sq mm [14 AWG] wire) to ground bus
nuts with captive star washer
Publication 1794-IN002G-EN-P - January 2004
16 FlexLogix Controller System
4 Make sure power is not applied to the power supply Connect the power supply to the adapter This diagram and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the left adapter connector terminal A to the bottom left power connector terminal G
b Connect -24V common to left adapter connector terminal B to the top left power connector terminal E
c Use connections C and D on the adapter and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the adapter to meet the requirements for installations in Class I Division 2 locations
5 Connect IO terminal bases and IO modules to the adapter the same way you connect them to the controller
6 Remove the plastic spacer from both ends of the extended-local IO cable (1794-CE1 or 1794-CE3)
plastic spacer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 17
7 Connect the adapter to the controller
The following diagram shows how you can also use the 1794-CE1 -CE3 cable to split a rail of IO You can split each rail only once You can split a rail right after the controller (or adapter) or after any IO module For more information about the 1794-CE1 -CE3 cables see the Interconnect Cable Installation Instructions publication 1794-512
Removing the extended-local adapterIf you need to remove the adapter follow these steps
1 Turn off power to the adapter
2 Disconnect all cables from the adapter
3 Remove the IO module that is adjacent to the adapter
4 On the terminal base adjacent to the adapter slide the FLEXBUS connector away from the adapter and remove the IO terminal base
5 Remove the adapter from the DIN rail
31039-M
1794-CE1 or 1794-CE3 cable
LOCAL rail
LOCAL2 rail
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
Publication 1794-IN002G-EN-P - January 2004
18 FlexLogix Controller System
Make an RS-232 Connection to the ControllerThe RS-232 port is a non-isolated serial port built-in to the front of the controller
To connect to the serial port
1 Determine whether you need an optical isolator
If you connect the controller to a device outside of the systemrsquos enclosure consider installing an isolator between the controller and device
One possible isolator is the 1761-NET-AIC interface converter
serial port
port 1 DB-9 RS-232 DTE
baud rate selector switch
port 2 mini-DIN 8 RS-232
dc power source selector switch
terminals for external 24V dc power supply
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 19
2 Select the appropriate cable
Are you using an isolator
Use this cable
no The 1756-CP3 cable attaches the controller directly to the controller
If you make your own cable it must be shielded and the shields must be tied to the metal shell (that surrounds the pins) on both ends of the cableYou can also use a 1747-CP3 cable (from the SLC product family) This cable has a taller right-angle connector housing than the 1756-CP3 cable
yes The 1761-CBL-AP00 cable (right-angle connector to controller) or the 1761-CBL-PM02 cable (straight connector to the controller) attaches the controller to port 2 on the 1761-NET-AIC isolator The mini-DIN connector is not commercially available so you cannot make this cable
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
DB-9 right-angle or straight cable end 8-pin mini-DIN cable end
Pin DB-9 end Mini-DIN end1 DCD DCD
2 RxD RxD
3 TxD TxD
4 DTR DTR
5 ground ground
6 DSR DSR
7 RTS RTS
8 CTS CTS
9 na na
1 2
34
5
6 7867
8
9
1
2
3
4
5
Publication 1794-IN002G-EN-P - January 2004
20 FlexLogix Controller System
3 Connect the appropriate cable to the serial port on the controller
Be sure that power is removed or the area is nonhazardous before proceeding
4 If necessary attach the controller to the isolator
WARNING If you connect or disconnect the serial cable with power applied to this module or the serial device on the other end of the cable an electrical arc can occur This could cause an explosion in hazardous location installations
modem
1761-NET-AIC isolator
user-supplied modem cable
1761 cable
system enclosure
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 21
Select the Operating Mode of the Controller
1 Use this table to determine the operating mode of the controller
2 Turn the key on the front panel of the controller to select the mode
If you want to Select one of these modes
Run Program Remote
Run Program Test
turn outputs to the state commanded by the logic of the project
YES YES
turn outputs to their configured state for Program mode
YES YES YES
execute (scan) tasks YES YES YES
change the mode of the controller through software
YES YES YES
download a project YES YES
schedule a ControlNet network YES YES
while online edit the project YES YES YES YES
To select Turn the key to
Remote Run RUN and then to REM
Remote Program PROG and then to REM
Remote Test REM and then go online and select Test mode via the programming software
keyswitch
Publication 1794-IN002G-EN-P - January 2004
22 FlexLogix Controller System
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware RevisionTo update the firmware of a controller first install a firmware upgrade kit
bull An upgrade kit ships on a supplemental CD along with RSLogix 5000 software
bull To download an upgrade kit go to httpsupportrockwellautomationcom Choose Firmware Updates
Indicator Color Description
RUN off bull no task(s) running
bull controller in Program mode
green bull one or more tasks are running
bull controller is in Run mode
OK off no power applied
red flashing after initially installing the controller - the controller requires a FLASH upgrade to the proper firmware revision see belowafter the controller is operating - recoverable fault
red bull controller faulted
bull clear faults clear memory or replace the controller
green controller OK
BATTERY off battery will support memory
red bull battery may not support memory
bull replace battery
IO off bull controller project not downloaded (the condition after power up)
bull no IO or communications configured
green communicating to all devices
green flashing one or more devices are not responding
LOCALandLOCAL2
off rail is inhibited
green communicating to all devices on that rail
green flashing one or more devices on that rail not responding
red flashing no modules exist on that rail
RS232 off no activity
green data being received or transmitted
FORCE off no forces present
amber forces present
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 23
Update the Controller
1 Connect the controller to the same network as your workstation
2 Start ControlFLASH software
3 Choose Next gt
4 Select the catalog number of the controller and choose Next gt
5 Expand the network until you see the controller If the required network is not shown first configure a driver for the network in RSLinx software
6 Select the controller and choose OK
7 Select the revision level to which you want to update the controller and choose Next gt
8 To start the update of the controller choose Finish and then Yes
After the controller is updated the status box displays Update complete
9 Choose OK
10 To close ControlFLASH software choose Cancel and then Yes
TIP RSLogix 5000 software revision 100 or later lets you update controller firmware as part of the download sequence To update the controller download your project and follow the prompts of the software
IMPORTANT If the Revision list is empty download a new upgrade kit Some older upgrade kits do not work with new controllers
weight 1794-L33 71 kg (156 lbs oz)1794-L34 75 g (166 lbs)(no communication cards installed)
28 kg (62 lbs)
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 27
power supply 1794-PS3 or 1794-PS13 ndash In applications that must be compliant with CSA requirements use a Separated Extra-Low Voltage (SELV) power supply that is compliant with IEC 610101 Annex H
power conductors 60deg C (140deg F) minimum copper22 to 14 AWG (0324 to 208 sq mm) stranded364 inch (12mm) insulation maximumlength 10m or less
category 3(2)
power connector torque 5 to 7 inch-pounds (06 to 08Nm)
battery 1756-BA1 (AB part number 94194801)059g lithium
na
serial cable 1761-CBLPM02 to 1761-NET-AIC 1761-CBLPA00 to 1761-NET-AIC1756-CP3 directly to controller1747-CP3 directly to controller
DIN rail steel 35 x 755mm DIN railA-B part number 199-DR1 46277-3 EN 50022
operating temperature IEC 60068-2-1 (Test Ad Operating Cold)IEC 60068-2-2 (Test Bd Operating Dry Heat)IEC 60068-2-14 (Test Nb Operating Thermal Shock)0 to 60degC (32 to 140degF)
storage temperature IEC 60068-2-1 (Test Ab Un-packaged Non-operating Cold)IEC 60068-2-2 (Test Bb Un-packaged Non-operating Dry Heat)IEC 60068-2-14 (Test Na Un-packaged Non-operating Thermal Shock)ndash40 to 85degC (ndash40 to 185degF)
relative humidity IEC 60068-2-30 (Test Db Un-packaged Non-operating Damp Heat)5 to 95 non-condensing
vibration(3) IEC60068-2-6 (Test Fc Operating) 5g 10-500Hz
shock(3)
operatingnon-operating
IEC60068-2-27 (Test Ea Unpackaged shock)
30g50g
emissions CISPR 11Group 1 Class A (with appropriate enclosure)
ESD immunity IEC 61000-4-26kV contact discharges8kV air discharges
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
RA-QR005C-EN-E 608
FlexLogix Controller System 7
Removal and Insertion Under PowerThe FlexLogix controller the extended-local IO adapter the communication daughtercards and the IO terminal bases cannot be removed or inserted under power
However you can remove and insert FLEX IO modules while backplane power is applied and the system is operating
Be sure that power is removed or the area is nonhazardous before proceeding
Other Considerations
WARNING If you insert or remove the module while backplane power is on an electrical arc can occur This could cause an explosion in hazardous location installations
ATTENTION Also consider the following before you install your FlexLogix controller
bull This product is grounded through the DIN rail to chassis ground Use zinc plated yellow-chromate steel DIN rail to assure proper grounding The use of other DIN rail materials (eg aluminum plastic etc) that can corrode oxidize or are poor conductors can result in improper or intermittent grounding
bull Power connection length should be less than 10 meters
Publication 1794-IN002G-EN-P - January 2004
8 FlexLogix Controller System
What You Need to DoBefore you can install a FlexLogix controller or extended-local adapter you must
Install steel 35 x 755mm DIN rails (A-B part number 199-DR1 46277-3) where you want to place the FlexLogix system components
The DIN rails for all FlexLogix system components including all local and extended-local IO modules must be mounted on a common conductive surface to ensure proper electromagnetic interference (EMI) performance See 24 and 25 for approximate mounting dimensions and mounting clearances
For more information about mounting DIN rails and splitting IO across DIN rails see the FLEX IO Product Data publication 1794-21
Use DIN rail locks (A-B catalog number 1492-EA35) to meet the shock and vibrations specifications listed on 26 A pair of DIN locks comes with the controller
Mount an appropriate power supply on an appropriate DIN rail See the specifications on 26
To install a FlexLogix controller
Step 1 Verify That You Have All the Components see page 9
Step 2 Install the Battery see page 10
Step 3 Install Communication Daughtercards (optional) see page 11
Step 4 Install the Controller see page 12
Step 5 Install the Extended-Local Adapter (optional) see page 15
After you install the FlexLogix controller you can
Make an RS-232 Connection to the Controller see page 18
Select the Operating Mode of the Controller see page 21
Monitor the Controller LEDs see page 22
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 9
Step 1 Verify That You Have All the ComponentsThese components ship with the FlexLogix controller
bull 1756-BA1 battery and label
bull key
bull one spring-clip connector plug for 24V power connection
bull one screw-terminal connector plug for 24V power connection
bull two 1492-EA35 DIN rail locks
The system components you have depend on your application You might have
FlexLogix System Component Description
1788-CNC -CNCR for ControlNet communications1788-CNF -CNFR for ControlNet communications1788-DNBO for DeviceNet communications1788-ENBT for EtherNetIP communications
1756-CP3You can also use the 1747-CP3 cable from the SLC product family
1794-FLA
1794-CE1 (1 foot)1794-CE3 (3 foot)
communication card
serial cable
FlexLogix extended-local adapter
extended- local IO cable
Publication 1794-IN002G-EN-P - January 2004
10 FlexLogix Controller System
Step 2 Install the Battery
For Safety information on the handling of lithium batteries including handling and disposal of leaking batteries see Guidelines for Handling Lithium Batteries publication AG 5-4
1 Install a 1756-BA1 battery
2 Attach the battery label
a Write on the battery label the date you install the battery
b Attach the label to the inside of the battery compartment
ATTENTION Only install a 1756-BA1 battery If you install a different battery you may damage the controller
WARNING For safety information on the handling of lithium batteries in-cluding the handling and disposal of leaking batteries see Guide-lines for Handling Lithium Batteries publication AG-54Store batteries in a cool dry environment We recommend 25degC with 40 to 60 relative humidity You may store batteries for up to 30 days between -45deg to 85degC such as during transporta-tion To avoid possible leakage do not store batteries above 60degC for more than 30 days
When you connect or disconnect the battery an electrical arc can occur This could cause an explosion in hazardous location in-stallations Be sure that power is removed or the area is nonhaz-ardous before proceeding
Attach battery here
top red lead (+)
middle black lead (-)
bottom no connection
Attach label here
This jumper is for service use only Do not use this jumper
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 11
Step 3 Install Communication Daughtercards (optional)
For specific information about configuring the communication card (such as setting a node address) see the installation instructions for the communication card
1 Turn off power to the controller
2 If necessary remove the blank cover from the communication slot
3 Slide the communication card into the communication slot Be sure to line up the card with the card guides in the controller
4 Record which slot you use for the communication card You need the slot number when you develop your controller application
5 Secure the card with the screws to ensure proper grounding Do not over-tighten the screws The maximum torque for the card screws is 48 to 52 inch pounds (05 to 06 Nm)
6 After the controller is installed (see page 12) connect the network cable
Removing a Communication CardIf you need to remove a communication card from the controller
1 Turn off power to the controller
2 Disconnect all cables from the communication card
3 Loosen the card screws from the communication card
4 Remove the card from the controller
5 Replace the card with a blank cover or a different communication card
WARNING If you insert or remove the card while host power is on an electrical arc can occur This could cause an explosion in haz-ardous location installations
31032-M
slot 1slot 2
Publication 1794-IN002G-EN-P - January 2004
12 FlexLogix Controller System
Step 4 Install the Controller
1 Position the FlexLogix controller on the DIN rail at a 5deg angle and rotate the controller onto the DIN rail
2 Press the controller down onto the DIN rail until flush The locking tabs will snap into position and lock the controller onto the DIN rail
If the controller does not lock in place use a screwdriver or similar device to move the locking tabs down while pressing the controller onto the DIN rail Release the locking tabs to lock the controller in place If necessary push up on the locking tabs to lock
3 Ground the controller The DIN rail and the common conductive surface behind the DIN rail provide functional ground for the controller Use the grounding stud to meet safety ground requirements
For information about wiring and grounding see the Industrial Automation Wiring and Grounding Guidelines publication 1770-41
IMPORTANT You can mount the FlexLogix controller either vertically or horizontally (as shown)
A
A
locking tabs
grounding stud
Equipment grounding conductor (ground lug with 208 sq mm [14 AWG] wire) to ground bus
nuts with captive star washer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 13
4 Make sure power is not applied to the power supply
5 Connect the power supply to the controller The graphic below and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the top of the controller connector terminal A to the bottom left power connector terminal G
b Connect -24V common to top controller connector terminal B to the top left power connector terminal E
c Use connections C and D on the controller and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the controller to meet the requirements for installations in Class I Division 2 locations
WARNING If you connect or disconnect wiring while the field-side power is on an electrical arc can occur This could cause an explosion in hazardous location installations Be sure that power is re-moved or the area is nonhazardous before proceeding
+
+
A
B
C
D
FE
HG
_
_
Publication 1794-IN002G-EN-P - January 2004
14 FlexLogix Controller System
6 Mount the IO terminal bases on the DIN rail
For information about IO terminal bases see the FLEX IO Terminal Base Installation Instructions publication 1794-IN092
7 Install the IO modules
To install an IO module see the installation instructions for that module
Removing the controllerIf you need to remove the controller follow these steps
1 Turn off power to the controller
2 Disconnect all cables from the controller
3 Remove the IO module that is adjacent to the controller
4 On the terminal base adjacent to the controller slide the FLEXBUS connector away from the controller and remove the IO terminal base
5 Remove the controller from the DIN rail
B
A
A
31036-M
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 15
Step 5 Install the Extended-Local Adapter (optional)
1 Position the 1794-FLA extended-local IO adapter on the DIN rail at a 30deg angle and rotate the adapter onto the DIN rail
2 Press the adapter down onto the DIN rail until flush The locking tab will snap into position and lock the adapter onto the DIN rail
If the adapter does not lock in place use a screwdriver or similar device to move the locking tab down while pressing the adapter onto the DIN rail Release the locking tab to lock the adapter in place If necessary push up on the locking tab to lock
3 Ground the adapter The adapter is grounded through the steel DIN rail and the common conductive surface behind the DIN rail Additionally use the grounding stud
grounding stud
Equipment grounding conductor (ground lug with 208 sq mm [14 AWG] wire) to ground bus
nuts with captive star washer
Publication 1794-IN002G-EN-P - January 2004
16 FlexLogix Controller System
4 Make sure power is not applied to the power supply Connect the power supply to the adapter This diagram and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the left adapter connector terminal A to the bottom left power connector terminal G
b Connect -24V common to left adapter connector terminal B to the top left power connector terminal E
c Use connections C and D on the adapter and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the adapter to meet the requirements for installations in Class I Division 2 locations
5 Connect IO terminal bases and IO modules to the adapter the same way you connect them to the controller
6 Remove the plastic spacer from both ends of the extended-local IO cable (1794-CE1 or 1794-CE3)
plastic spacer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 17
7 Connect the adapter to the controller
The following diagram shows how you can also use the 1794-CE1 -CE3 cable to split a rail of IO You can split each rail only once You can split a rail right after the controller (or adapter) or after any IO module For more information about the 1794-CE1 -CE3 cables see the Interconnect Cable Installation Instructions publication 1794-512
Removing the extended-local adapterIf you need to remove the adapter follow these steps
1 Turn off power to the adapter
2 Disconnect all cables from the adapter
3 Remove the IO module that is adjacent to the adapter
4 On the terminal base adjacent to the adapter slide the FLEXBUS connector away from the adapter and remove the IO terminal base
5 Remove the adapter from the DIN rail
31039-M
1794-CE1 or 1794-CE3 cable
LOCAL rail
LOCAL2 rail
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
Publication 1794-IN002G-EN-P - January 2004
18 FlexLogix Controller System
Make an RS-232 Connection to the ControllerThe RS-232 port is a non-isolated serial port built-in to the front of the controller
To connect to the serial port
1 Determine whether you need an optical isolator
If you connect the controller to a device outside of the systemrsquos enclosure consider installing an isolator between the controller and device
One possible isolator is the 1761-NET-AIC interface converter
serial port
port 1 DB-9 RS-232 DTE
baud rate selector switch
port 2 mini-DIN 8 RS-232
dc power source selector switch
terminals for external 24V dc power supply
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 19
2 Select the appropriate cable
Are you using an isolator
Use this cable
no The 1756-CP3 cable attaches the controller directly to the controller
If you make your own cable it must be shielded and the shields must be tied to the metal shell (that surrounds the pins) on both ends of the cableYou can also use a 1747-CP3 cable (from the SLC product family) This cable has a taller right-angle connector housing than the 1756-CP3 cable
yes The 1761-CBL-AP00 cable (right-angle connector to controller) or the 1761-CBL-PM02 cable (straight connector to the controller) attaches the controller to port 2 on the 1761-NET-AIC isolator The mini-DIN connector is not commercially available so you cannot make this cable
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
DB-9 right-angle or straight cable end 8-pin mini-DIN cable end
Pin DB-9 end Mini-DIN end1 DCD DCD
2 RxD RxD
3 TxD TxD
4 DTR DTR
5 ground ground
6 DSR DSR
7 RTS RTS
8 CTS CTS
9 na na
1 2
34
5
6 7867
8
9
1
2
3
4
5
Publication 1794-IN002G-EN-P - January 2004
20 FlexLogix Controller System
3 Connect the appropriate cable to the serial port on the controller
Be sure that power is removed or the area is nonhazardous before proceeding
4 If necessary attach the controller to the isolator
WARNING If you connect or disconnect the serial cable with power applied to this module or the serial device on the other end of the cable an electrical arc can occur This could cause an explosion in hazardous location installations
modem
1761-NET-AIC isolator
user-supplied modem cable
1761 cable
system enclosure
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 21
Select the Operating Mode of the Controller
1 Use this table to determine the operating mode of the controller
2 Turn the key on the front panel of the controller to select the mode
If you want to Select one of these modes
Run Program Remote
Run Program Test
turn outputs to the state commanded by the logic of the project
YES YES
turn outputs to their configured state for Program mode
YES YES YES
execute (scan) tasks YES YES YES
change the mode of the controller through software
YES YES YES
download a project YES YES
schedule a ControlNet network YES YES
while online edit the project YES YES YES YES
To select Turn the key to
Remote Run RUN and then to REM
Remote Program PROG and then to REM
Remote Test REM and then go online and select Test mode via the programming software
keyswitch
Publication 1794-IN002G-EN-P - January 2004
22 FlexLogix Controller System
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware RevisionTo update the firmware of a controller first install a firmware upgrade kit
bull An upgrade kit ships on a supplemental CD along with RSLogix 5000 software
bull To download an upgrade kit go to httpsupportrockwellautomationcom Choose Firmware Updates
Indicator Color Description
RUN off bull no task(s) running
bull controller in Program mode
green bull one or more tasks are running
bull controller is in Run mode
OK off no power applied
red flashing after initially installing the controller - the controller requires a FLASH upgrade to the proper firmware revision see belowafter the controller is operating - recoverable fault
red bull controller faulted
bull clear faults clear memory or replace the controller
green controller OK
BATTERY off battery will support memory
red bull battery may not support memory
bull replace battery
IO off bull controller project not downloaded (the condition after power up)
bull no IO or communications configured
green communicating to all devices
green flashing one or more devices are not responding
LOCALandLOCAL2
off rail is inhibited
green communicating to all devices on that rail
green flashing one or more devices on that rail not responding
red flashing no modules exist on that rail
RS232 off no activity
green data being received or transmitted
FORCE off no forces present
amber forces present
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 23
Update the Controller
1 Connect the controller to the same network as your workstation
2 Start ControlFLASH software
3 Choose Next gt
4 Select the catalog number of the controller and choose Next gt
5 Expand the network until you see the controller If the required network is not shown first configure a driver for the network in RSLinx software
6 Select the controller and choose OK
7 Select the revision level to which you want to update the controller and choose Next gt
8 To start the update of the controller choose Finish and then Yes
After the controller is updated the status box displays Update complete
9 Choose OK
10 To close ControlFLASH software choose Cancel and then Yes
TIP RSLogix 5000 software revision 100 or later lets you update controller firmware as part of the download sequence To update the controller download your project and follow the prompts of the software
IMPORTANT If the Revision list is empty download a new upgrade kit Some older upgrade kits do not work with new controllers
weight 1794-L33 71 kg (156 lbs oz)1794-L34 75 g (166 lbs)(no communication cards installed)
28 kg (62 lbs)
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 27
power supply 1794-PS3 or 1794-PS13 ndash In applications that must be compliant with CSA requirements use a Separated Extra-Low Voltage (SELV) power supply that is compliant with IEC 610101 Annex H
power conductors 60deg C (140deg F) minimum copper22 to 14 AWG (0324 to 208 sq mm) stranded364 inch (12mm) insulation maximumlength 10m or less
category 3(2)
power connector torque 5 to 7 inch-pounds (06 to 08Nm)
battery 1756-BA1 (AB part number 94194801)059g lithium
na
serial cable 1761-CBLPM02 to 1761-NET-AIC 1761-CBLPA00 to 1761-NET-AIC1756-CP3 directly to controller1747-CP3 directly to controller
DIN rail steel 35 x 755mm DIN railA-B part number 199-DR1 46277-3 EN 50022
operating temperature IEC 60068-2-1 (Test Ad Operating Cold)IEC 60068-2-2 (Test Bd Operating Dry Heat)IEC 60068-2-14 (Test Nb Operating Thermal Shock)0 to 60degC (32 to 140degF)
storage temperature IEC 60068-2-1 (Test Ab Un-packaged Non-operating Cold)IEC 60068-2-2 (Test Bb Un-packaged Non-operating Dry Heat)IEC 60068-2-14 (Test Na Un-packaged Non-operating Thermal Shock)ndash40 to 85degC (ndash40 to 185degF)
relative humidity IEC 60068-2-30 (Test Db Un-packaged Non-operating Damp Heat)5 to 95 non-condensing
vibration(3) IEC60068-2-6 (Test Fc Operating) 5g 10-500Hz
shock(3)
operatingnon-operating
IEC60068-2-27 (Test Ea Unpackaged shock)
30g50g
emissions CISPR 11Group 1 Class A (with appropriate enclosure)
ESD immunity IEC 61000-4-26kV contact discharges8kV air discharges
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
RA-QR005C-EN-E 608
8 FlexLogix Controller System
What You Need to DoBefore you can install a FlexLogix controller or extended-local adapter you must
Install steel 35 x 755mm DIN rails (A-B part number 199-DR1 46277-3) where you want to place the FlexLogix system components
The DIN rails for all FlexLogix system components including all local and extended-local IO modules must be mounted on a common conductive surface to ensure proper electromagnetic interference (EMI) performance See 24 and 25 for approximate mounting dimensions and mounting clearances
For more information about mounting DIN rails and splitting IO across DIN rails see the FLEX IO Product Data publication 1794-21
Use DIN rail locks (A-B catalog number 1492-EA35) to meet the shock and vibrations specifications listed on 26 A pair of DIN locks comes with the controller
Mount an appropriate power supply on an appropriate DIN rail See the specifications on 26
To install a FlexLogix controller
Step 1 Verify That You Have All the Components see page 9
Step 2 Install the Battery see page 10
Step 3 Install Communication Daughtercards (optional) see page 11
Step 4 Install the Controller see page 12
Step 5 Install the Extended-Local Adapter (optional) see page 15
After you install the FlexLogix controller you can
Make an RS-232 Connection to the Controller see page 18
Select the Operating Mode of the Controller see page 21
Monitor the Controller LEDs see page 22
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 9
Step 1 Verify That You Have All the ComponentsThese components ship with the FlexLogix controller
bull 1756-BA1 battery and label
bull key
bull one spring-clip connector plug for 24V power connection
bull one screw-terminal connector plug for 24V power connection
bull two 1492-EA35 DIN rail locks
The system components you have depend on your application You might have
FlexLogix System Component Description
1788-CNC -CNCR for ControlNet communications1788-CNF -CNFR for ControlNet communications1788-DNBO for DeviceNet communications1788-ENBT for EtherNetIP communications
1756-CP3You can also use the 1747-CP3 cable from the SLC product family
1794-FLA
1794-CE1 (1 foot)1794-CE3 (3 foot)
communication card
serial cable
FlexLogix extended-local adapter
extended- local IO cable
Publication 1794-IN002G-EN-P - January 2004
10 FlexLogix Controller System
Step 2 Install the Battery
For Safety information on the handling of lithium batteries including handling and disposal of leaking batteries see Guidelines for Handling Lithium Batteries publication AG 5-4
1 Install a 1756-BA1 battery
2 Attach the battery label
a Write on the battery label the date you install the battery
b Attach the label to the inside of the battery compartment
ATTENTION Only install a 1756-BA1 battery If you install a different battery you may damage the controller
WARNING For safety information on the handling of lithium batteries in-cluding the handling and disposal of leaking batteries see Guide-lines for Handling Lithium Batteries publication AG-54Store batteries in a cool dry environment We recommend 25degC with 40 to 60 relative humidity You may store batteries for up to 30 days between -45deg to 85degC such as during transporta-tion To avoid possible leakage do not store batteries above 60degC for more than 30 days
When you connect or disconnect the battery an electrical arc can occur This could cause an explosion in hazardous location in-stallations Be sure that power is removed or the area is nonhaz-ardous before proceeding
Attach battery here
top red lead (+)
middle black lead (-)
bottom no connection
Attach label here
This jumper is for service use only Do not use this jumper
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 11
Step 3 Install Communication Daughtercards (optional)
For specific information about configuring the communication card (such as setting a node address) see the installation instructions for the communication card
1 Turn off power to the controller
2 If necessary remove the blank cover from the communication slot
3 Slide the communication card into the communication slot Be sure to line up the card with the card guides in the controller
4 Record which slot you use for the communication card You need the slot number when you develop your controller application
5 Secure the card with the screws to ensure proper grounding Do not over-tighten the screws The maximum torque for the card screws is 48 to 52 inch pounds (05 to 06 Nm)
6 After the controller is installed (see page 12) connect the network cable
Removing a Communication CardIf you need to remove a communication card from the controller
1 Turn off power to the controller
2 Disconnect all cables from the communication card
3 Loosen the card screws from the communication card
4 Remove the card from the controller
5 Replace the card with a blank cover or a different communication card
WARNING If you insert or remove the card while host power is on an electrical arc can occur This could cause an explosion in haz-ardous location installations
31032-M
slot 1slot 2
Publication 1794-IN002G-EN-P - January 2004
12 FlexLogix Controller System
Step 4 Install the Controller
1 Position the FlexLogix controller on the DIN rail at a 5deg angle and rotate the controller onto the DIN rail
2 Press the controller down onto the DIN rail until flush The locking tabs will snap into position and lock the controller onto the DIN rail
If the controller does not lock in place use a screwdriver or similar device to move the locking tabs down while pressing the controller onto the DIN rail Release the locking tabs to lock the controller in place If necessary push up on the locking tabs to lock
3 Ground the controller The DIN rail and the common conductive surface behind the DIN rail provide functional ground for the controller Use the grounding stud to meet safety ground requirements
For information about wiring and grounding see the Industrial Automation Wiring and Grounding Guidelines publication 1770-41
IMPORTANT You can mount the FlexLogix controller either vertically or horizontally (as shown)
A
A
locking tabs
grounding stud
Equipment grounding conductor (ground lug with 208 sq mm [14 AWG] wire) to ground bus
nuts with captive star washer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 13
4 Make sure power is not applied to the power supply
5 Connect the power supply to the controller The graphic below and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the top of the controller connector terminal A to the bottom left power connector terminal G
b Connect -24V common to top controller connector terminal B to the top left power connector terminal E
c Use connections C and D on the controller and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the controller to meet the requirements for installations in Class I Division 2 locations
WARNING If you connect or disconnect wiring while the field-side power is on an electrical arc can occur This could cause an explosion in hazardous location installations Be sure that power is re-moved or the area is nonhazardous before proceeding
+
+
A
B
C
D
FE
HG
_
_
Publication 1794-IN002G-EN-P - January 2004
14 FlexLogix Controller System
6 Mount the IO terminal bases on the DIN rail
For information about IO terminal bases see the FLEX IO Terminal Base Installation Instructions publication 1794-IN092
7 Install the IO modules
To install an IO module see the installation instructions for that module
Removing the controllerIf you need to remove the controller follow these steps
1 Turn off power to the controller
2 Disconnect all cables from the controller
3 Remove the IO module that is adjacent to the controller
4 On the terminal base adjacent to the controller slide the FLEXBUS connector away from the controller and remove the IO terminal base
5 Remove the controller from the DIN rail
B
A
A
31036-M
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 15
Step 5 Install the Extended-Local Adapter (optional)
1 Position the 1794-FLA extended-local IO adapter on the DIN rail at a 30deg angle and rotate the adapter onto the DIN rail
2 Press the adapter down onto the DIN rail until flush The locking tab will snap into position and lock the adapter onto the DIN rail
If the adapter does not lock in place use a screwdriver or similar device to move the locking tab down while pressing the adapter onto the DIN rail Release the locking tab to lock the adapter in place If necessary push up on the locking tab to lock
3 Ground the adapter The adapter is grounded through the steel DIN rail and the common conductive surface behind the DIN rail Additionally use the grounding stud
grounding stud
Equipment grounding conductor (ground lug with 208 sq mm [14 AWG] wire) to ground bus
nuts with captive star washer
Publication 1794-IN002G-EN-P - January 2004
16 FlexLogix Controller System
4 Make sure power is not applied to the power supply Connect the power supply to the adapter This diagram and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the left adapter connector terminal A to the bottom left power connector terminal G
b Connect -24V common to left adapter connector terminal B to the top left power connector terminal E
c Use connections C and D on the adapter and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the adapter to meet the requirements for installations in Class I Division 2 locations
5 Connect IO terminal bases and IO modules to the adapter the same way you connect them to the controller
6 Remove the plastic spacer from both ends of the extended-local IO cable (1794-CE1 or 1794-CE3)
plastic spacer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 17
7 Connect the adapter to the controller
The following diagram shows how you can also use the 1794-CE1 -CE3 cable to split a rail of IO You can split each rail only once You can split a rail right after the controller (or adapter) or after any IO module For more information about the 1794-CE1 -CE3 cables see the Interconnect Cable Installation Instructions publication 1794-512
Removing the extended-local adapterIf you need to remove the adapter follow these steps
1 Turn off power to the adapter
2 Disconnect all cables from the adapter
3 Remove the IO module that is adjacent to the adapter
4 On the terminal base adjacent to the adapter slide the FLEXBUS connector away from the adapter and remove the IO terminal base
5 Remove the adapter from the DIN rail
31039-M
1794-CE1 or 1794-CE3 cable
LOCAL rail
LOCAL2 rail
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
Publication 1794-IN002G-EN-P - January 2004
18 FlexLogix Controller System
Make an RS-232 Connection to the ControllerThe RS-232 port is a non-isolated serial port built-in to the front of the controller
To connect to the serial port
1 Determine whether you need an optical isolator
If you connect the controller to a device outside of the systemrsquos enclosure consider installing an isolator between the controller and device
One possible isolator is the 1761-NET-AIC interface converter
serial port
port 1 DB-9 RS-232 DTE
baud rate selector switch
port 2 mini-DIN 8 RS-232
dc power source selector switch
terminals for external 24V dc power supply
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 19
2 Select the appropriate cable
Are you using an isolator
Use this cable
no The 1756-CP3 cable attaches the controller directly to the controller
If you make your own cable it must be shielded and the shields must be tied to the metal shell (that surrounds the pins) on both ends of the cableYou can also use a 1747-CP3 cable (from the SLC product family) This cable has a taller right-angle connector housing than the 1756-CP3 cable
yes The 1761-CBL-AP00 cable (right-angle connector to controller) or the 1761-CBL-PM02 cable (straight connector to the controller) attaches the controller to port 2 on the 1761-NET-AIC isolator The mini-DIN connector is not commercially available so you cannot make this cable
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
DB-9 right-angle or straight cable end 8-pin mini-DIN cable end
Pin DB-9 end Mini-DIN end1 DCD DCD
2 RxD RxD
3 TxD TxD
4 DTR DTR
5 ground ground
6 DSR DSR
7 RTS RTS
8 CTS CTS
9 na na
1 2
34
5
6 7867
8
9
1
2
3
4
5
Publication 1794-IN002G-EN-P - January 2004
20 FlexLogix Controller System
3 Connect the appropriate cable to the serial port on the controller
Be sure that power is removed or the area is nonhazardous before proceeding
4 If necessary attach the controller to the isolator
WARNING If you connect or disconnect the serial cable with power applied to this module or the serial device on the other end of the cable an electrical arc can occur This could cause an explosion in hazardous location installations
modem
1761-NET-AIC isolator
user-supplied modem cable
1761 cable
system enclosure
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 21
Select the Operating Mode of the Controller
1 Use this table to determine the operating mode of the controller
2 Turn the key on the front panel of the controller to select the mode
If you want to Select one of these modes
Run Program Remote
Run Program Test
turn outputs to the state commanded by the logic of the project
YES YES
turn outputs to their configured state for Program mode
YES YES YES
execute (scan) tasks YES YES YES
change the mode of the controller through software
YES YES YES
download a project YES YES
schedule a ControlNet network YES YES
while online edit the project YES YES YES YES
To select Turn the key to
Remote Run RUN and then to REM
Remote Program PROG and then to REM
Remote Test REM and then go online and select Test mode via the programming software
keyswitch
Publication 1794-IN002G-EN-P - January 2004
22 FlexLogix Controller System
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware RevisionTo update the firmware of a controller first install a firmware upgrade kit
bull An upgrade kit ships on a supplemental CD along with RSLogix 5000 software
bull To download an upgrade kit go to httpsupportrockwellautomationcom Choose Firmware Updates
Indicator Color Description
RUN off bull no task(s) running
bull controller in Program mode
green bull one or more tasks are running
bull controller is in Run mode
OK off no power applied
red flashing after initially installing the controller - the controller requires a FLASH upgrade to the proper firmware revision see belowafter the controller is operating - recoverable fault
red bull controller faulted
bull clear faults clear memory or replace the controller
green controller OK
BATTERY off battery will support memory
red bull battery may not support memory
bull replace battery
IO off bull controller project not downloaded (the condition after power up)
bull no IO or communications configured
green communicating to all devices
green flashing one or more devices are not responding
LOCALandLOCAL2
off rail is inhibited
green communicating to all devices on that rail
green flashing one or more devices on that rail not responding
red flashing no modules exist on that rail
RS232 off no activity
green data being received or transmitted
FORCE off no forces present
amber forces present
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 23
Update the Controller
1 Connect the controller to the same network as your workstation
2 Start ControlFLASH software
3 Choose Next gt
4 Select the catalog number of the controller and choose Next gt
5 Expand the network until you see the controller If the required network is not shown first configure a driver for the network in RSLinx software
6 Select the controller and choose OK
7 Select the revision level to which you want to update the controller and choose Next gt
8 To start the update of the controller choose Finish and then Yes
After the controller is updated the status box displays Update complete
9 Choose OK
10 To close ControlFLASH software choose Cancel and then Yes
TIP RSLogix 5000 software revision 100 or later lets you update controller firmware as part of the download sequence To update the controller download your project and follow the prompts of the software
IMPORTANT If the Revision list is empty download a new upgrade kit Some older upgrade kits do not work with new controllers
weight 1794-L33 71 kg (156 lbs oz)1794-L34 75 g (166 lbs)(no communication cards installed)
28 kg (62 lbs)
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 27
power supply 1794-PS3 or 1794-PS13 ndash In applications that must be compliant with CSA requirements use a Separated Extra-Low Voltage (SELV) power supply that is compliant with IEC 610101 Annex H
power conductors 60deg C (140deg F) minimum copper22 to 14 AWG (0324 to 208 sq mm) stranded364 inch (12mm) insulation maximumlength 10m or less
category 3(2)
power connector torque 5 to 7 inch-pounds (06 to 08Nm)
battery 1756-BA1 (AB part number 94194801)059g lithium
na
serial cable 1761-CBLPM02 to 1761-NET-AIC 1761-CBLPA00 to 1761-NET-AIC1756-CP3 directly to controller1747-CP3 directly to controller
DIN rail steel 35 x 755mm DIN railA-B part number 199-DR1 46277-3 EN 50022
operating temperature IEC 60068-2-1 (Test Ad Operating Cold)IEC 60068-2-2 (Test Bd Operating Dry Heat)IEC 60068-2-14 (Test Nb Operating Thermal Shock)0 to 60degC (32 to 140degF)
storage temperature IEC 60068-2-1 (Test Ab Un-packaged Non-operating Cold)IEC 60068-2-2 (Test Bb Un-packaged Non-operating Dry Heat)IEC 60068-2-14 (Test Na Un-packaged Non-operating Thermal Shock)ndash40 to 85degC (ndash40 to 185degF)
relative humidity IEC 60068-2-30 (Test Db Un-packaged Non-operating Damp Heat)5 to 95 non-condensing
vibration(3) IEC60068-2-6 (Test Fc Operating) 5g 10-500Hz
shock(3)
operatingnon-operating
IEC60068-2-27 (Test Ea Unpackaged shock)
30g50g
emissions CISPR 11Group 1 Class A (with appropriate enclosure)
ESD immunity IEC 61000-4-26kV contact discharges8kV air discharges
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
RA-QR005C-EN-E 608
FlexLogix Controller System 9
Step 1 Verify That You Have All the ComponentsThese components ship with the FlexLogix controller
bull 1756-BA1 battery and label
bull key
bull one spring-clip connector plug for 24V power connection
bull one screw-terminal connector plug for 24V power connection
bull two 1492-EA35 DIN rail locks
The system components you have depend on your application You might have
FlexLogix System Component Description
1788-CNC -CNCR for ControlNet communications1788-CNF -CNFR for ControlNet communications1788-DNBO for DeviceNet communications1788-ENBT for EtherNetIP communications
1756-CP3You can also use the 1747-CP3 cable from the SLC product family
1794-FLA
1794-CE1 (1 foot)1794-CE3 (3 foot)
communication card
serial cable
FlexLogix extended-local adapter
extended- local IO cable
Publication 1794-IN002G-EN-P - January 2004
10 FlexLogix Controller System
Step 2 Install the Battery
For Safety information on the handling of lithium batteries including handling and disposal of leaking batteries see Guidelines for Handling Lithium Batteries publication AG 5-4
1 Install a 1756-BA1 battery
2 Attach the battery label
a Write on the battery label the date you install the battery
b Attach the label to the inside of the battery compartment
ATTENTION Only install a 1756-BA1 battery If you install a different battery you may damage the controller
WARNING For safety information on the handling of lithium batteries in-cluding the handling and disposal of leaking batteries see Guide-lines for Handling Lithium Batteries publication AG-54Store batteries in a cool dry environment We recommend 25degC with 40 to 60 relative humidity You may store batteries for up to 30 days between -45deg to 85degC such as during transporta-tion To avoid possible leakage do not store batteries above 60degC for more than 30 days
When you connect or disconnect the battery an electrical arc can occur This could cause an explosion in hazardous location in-stallations Be sure that power is removed or the area is nonhaz-ardous before proceeding
Attach battery here
top red lead (+)
middle black lead (-)
bottom no connection
Attach label here
This jumper is for service use only Do not use this jumper
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 11
Step 3 Install Communication Daughtercards (optional)
For specific information about configuring the communication card (such as setting a node address) see the installation instructions for the communication card
1 Turn off power to the controller
2 If necessary remove the blank cover from the communication slot
3 Slide the communication card into the communication slot Be sure to line up the card with the card guides in the controller
4 Record which slot you use for the communication card You need the slot number when you develop your controller application
5 Secure the card with the screws to ensure proper grounding Do not over-tighten the screws The maximum torque for the card screws is 48 to 52 inch pounds (05 to 06 Nm)
6 After the controller is installed (see page 12) connect the network cable
Removing a Communication CardIf you need to remove a communication card from the controller
1 Turn off power to the controller
2 Disconnect all cables from the communication card
3 Loosen the card screws from the communication card
4 Remove the card from the controller
5 Replace the card with a blank cover or a different communication card
WARNING If you insert or remove the card while host power is on an electrical arc can occur This could cause an explosion in haz-ardous location installations
31032-M
slot 1slot 2
Publication 1794-IN002G-EN-P - January 2004
12 FlexLogix Controller System
Step 4 Install the Controller
1 Position the FlexLogix controller on the DIN rail at a 5deg angle and rotate the controller onto the DIN rail
2 Press the controller down onto the DIN rail until flush The locking tabs will snap into position and lock the controller onto the DIN rail
If the controller does not lock in place use a screwdriver or similar device to move the locking tabs down while pressing the controller onto the DIN rail Release the locking tabs to lock the controller in place If necessary push up on the locking tabs to lock
3 Ground the controller The DIN rail and the common conductive surface behind the DIN rail provide functional ground for the controller Use the grounding stud to meet safety ground requirements
For information about wiring and grounding see the Industrial Automation Wiring and Grounding Guidelines publication 1770-41
IMPORTANT You can mount the FlexLogix controller either vertically or horizontally (as shown)
A
A
locking tabs
grounding stud
Equipment grounding conductor (ground lug with 208 sq mm [14 AWG] wire) to ground bus
nuts with captive star washer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 13
4 Make sure power is not applied to the power supply
5 Connect the power supply to the controller The graphic below and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the top of the controller connector terminal A to the bottom left power connector terminal G
b Connect -24V common to top controller connector terminal B to the top left power connector terminal E
c Use connections C and D on the controller and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the controller to meet the requirements for installations in Class I Division 2 locations
WARNING If you connect or disconnect wiring while the field-side power is on an electrical arc can occur This could cause an explosion in hazardous location installations Be sure that power is re-moved or the area is nonhazardous before proceeding
+
+
A
B
C
D
FE
HG
_
_
Publication 1794-IN002G-EN-P - January 2004
14 FlexLogix Controller System
6 Mount the IO terminal bases on the DIN rail
For information about IO terminal bases see the FLEX IO Terminal Base Installation Instructions publication 1794-IN092
7 Install the IO modules
To install an IO module see the installation instructions for that module
Removing the controllerIf you need to remove the controller follow these steps
1 Turn off power to the controller
2 Disconnect all cables from the controller
3 Remove the IO module that is adjacent to the controller
4 On the terminal base adjacent to the controller slide the FLEXBUS connector away from the controller and remove the IO terminal base
5 Remove the controller from the DIN rail
B
A
A
31036-M
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 15
Step 5 Install the Extended-Local Adapter (optional)
1 Position the 1794-FLA extended-local IO adapter on the DIN rail at a 30deg angle and rotate the adapter onto the DIN rail
2 Press the adapter down onto the DIN rail until flush The locking tab will snap into position and lock the adapter onto the DIN rail
If the adapter does not lock in place use a screwdriver or similar device to move the locking tab down while pressing the adapter onto the DIN rail Release the locking tab to lock the adapter in place If necessary push up on the locking tab to lock
3 Ground the adapter The adapter is grounded through the steel DIN rail and the common conductive surface behind the DIN rail Additionally use the grounding stud
grounding stud
Equipment grounding conductor (ground lug with 208 sq mm [14 AWG] wire) to ground bus
nuts with captive star washer
Publication 1794-IN002G-EN-P - January 2004
16 FlexLogix Controller System
4 Make sure power is not applied to the power supply Connect the power supply to the adapter This diagram and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the left adapter connector terminal A to the bottom left power connector terminal G
b Connect -24V common to left adapter connector terminal B to the top left power connector terminal E
c Use connections C and D on the adapter and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the adapter to meet the requirements for installations in Class I Division 2 locations
5 Connect IO terminal bases and IO modules to the adapter the same way you connect them to the controller
6 Remove the plastic spacer from both ends of the extended-local IO cable (1794-CE1 or 1794-CE3)
plastic spacer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 17
7 Connect the adapter to the controller
The following diagram shows how you can also use the 1794-CE1 -CE3 cable to split a rail of IO You can split each rail only once You can split a rail right after the controller (or adapter) or after any IO module For more information about the 1794-CE1 -CE3 cables see the Interconnect Cable Installation Instructions publication 1794-512
Removing the extended-local adapterIf you need to remove the adapter follow these steps
1 Turn off power to the adapter
2 Disconnect all cables from the adapter
3 Remove the IO module that is adjacent to the adapter
4 On the terminal base adjacent to the adapter slide the FLEXBUS connector away from the adapter and remove the IO terminal base
5 Remove the adapter from the DIN rail
31039-M
1794-CE1 or 1794-CE3 cable
LOCAL rail
LOCAL2 rail
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
Publication 1794-IN002G-EN-P - January 2004
18 FlexLogix Controller System
Make an RS-232 Connection to the ControllerThe RS-232 port is a non-isolated serial port built-in to the front of the controller
To connect to the serial port
1 Determine whether you need an optical isolator
If you connect the controller to a device outside of the systemrsquos enclosure consider installing an isolator between the controller and device
One possible isolator is the 1761-NET-AIC interface converter
serial port
port 1 DB-9 RS-232 DTE
baud rate selector switch
port 2 mini-DIN 8 RS-232
dc power source selector switch
terminals for external 24V dc power supply
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 19
2 Select the appropriate cable
Are you using an isolator
Use this cable
no The 1756-CP3 cable attaches the controller directly to the controller
If you make your own cable it must be shielded and the shields must be tied to the metal shell (that surrounds the pins) on both ends of the cableYou can also use a 1747-CP3 cable (from the SLC product family) This cable has a taller right-angle connector housing than the 1756-CP3 cable
yes The 1761-CBL-AP00 cable (right-angle connector to controller) or the 1761-CBL-PM02 cable (straight connector to the controller) attaches the controller to port 2 on the 1761-NET-AIC isolator The mini-DIN connector is not commercially available so you cannot make this cable
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
DB-9 right-angle or straight cable end 8-pin mini-DIN cable end
Pin DB-9 end Mini-DIN end1 DCD DCD
2 RxD RxD
3 TxD TxD
4 DTR DTR
5 ground ground
6 DSR DSR
7 RTS RTS
8 CTS CTS
9 na na
1 2
34
5
6 7867
8
9
1
2
3
4
5
Publication 1794-IN002G-EN-P - January 2004
20 FlexLogix Controller System
3 Connect the appropriate cable to the serial port on the controller
Be sure that power is removed or the area is nonhazardous before proceeding
4 If necessary attach the controller to the isolator
WARNING If you connect or disconnect the serial cable with power applied to this module or the serial device on the other end of the cable an electrical arc can occur This could cause an explosion in hazardous location installations
modem
1761-NET-AIC isolator
user-supplied modem cable
1761 cable
system enclosure
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 21
Select the Operating Mode of the Controller
1 Use this table to determine the operating mode of the controller
2 Turn the key on the front panel of the controller to select the mode
If you want to Select one of these modes
Run Program Remote
Run Program Test
turn outputs to the state commanded by the logic of the project
YES YES
turn outputs to their configured state for Program mode
YES YES YES
execute (scan) tasks YES YES YES
change the mode of the controller through software
YES YES YES
download a project YES YES
schedule a ControlNet network YES YES
while online edit the project YES YES YES YES
To select Turn the key to
Remote Run RUN and then to REM
Remote Program PROG and then to REM
Remote Test REM and then go online and select Test mode via the programming software
keyswitch
Publication 1794-IN002G-EN-P - January 2004
22 FlexLogix Controller System
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware RevisionTo update the firmware of a controller first install a firmware upgrade kit
bull An upgrade kit ships on a supplemental CD along with RSLogix 5000 software
bull To download an upgrade kit go to httpsupportrockwellautomationcom Choose Firmware Updates
Indicator Color Description
RUN off bull no task(s) running
bull controller in Program mode
green bull one or more tasks are running
bull controller is in Run mode
OK off no power applied
red flashing after initially installing the controller - the controller requires a FLASH upgrade to the proper firmware revision see belowafter the controller is operating - recoverable fault
red bull controller faulted
bull clear faults clear memory or replace the controller
green controller OK
BATTERY off battery will support memory
red bull battery may not support memory
bull replace battery
IO off bull controller project not downloaded (the condition after power up)
bull no IO or communications configured
green communicating to all devices
green flashing one or more devices are not responding
LOCALandLOCAL2
off rail is inhibited
green communicating to all devices on that rail
green flashing one or more devices on that rail not responding
red flashing no modules exist on that rail
RS232 off no activity
green data being received or transmitted
FORCE off no forces present
amber forces present
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 23
Update the Controller
1 Connect the controller to the same network as your workstation
2 Start ControlFLASH software
3 Choose Next gt
4 Select the catalog number of the controller and choose Next gt
5 Expand the network until you see the controller If the required network is not shown first configure a driver for the network in RSLinx software
6 Select the controller and choose OK
7 Select the revision level to which you want to update the controller and choose Next gt
8 To start the update of the controller choose Finish and then Yes
After the controller is updated the status box displays Update complete
9 Choose OK
10 To close ControlFLASH software choose Cancel and then Yes
TIP RSLogix 5000 software revision 100 or later lets you update controller firmware as part of the download sequence To update the controller download your project and follow the prompts of the software
IMPORTANT If the Revision list is empty download a new upgrade kit Some older upgrade kits do not work with new controllers
weight 1794-L33 71 kg (156 lbs oz)1794-L34 75 g (166 lbs)(no communication cards installed)
28 kg (62 lbs)
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 27
power supply 1794-PS3 or 1794-PS13 ndash In applications that must be compliant with CSA requirements use a Separated Extra-Low Voltage (SELV) power supply that is compliant with IEC 610101 Annex H
power conductors 60deg C (140deg F) minimum copper22 to 14 AWG (0324 to 208 sq mm) stranded364 inch (12mm) insulation maximumlength 10m or less
category 3(2)
power connector torque 5 to 7 inch-pounds (06 to 08Nm)
battery 1756-BA1 (AB part number 94194801)059g lithium
na
serial cable 1761-CBLPM02 to 1761-NET-AIC 1761-CBLPA00 to 1761-NET-AIC1756-CP3 directly to controller1747-CP3 directly to controller
DIN rail steel 35 x 755mm DIN railA-B part number 199-DR1 46277-3 EN 50022
operating temperature IEC 60068-2-1 (Test Ad Operating Cold)IEC 60068-2-2 (Test Bd Operating Dry Heat)IEC 60068-2-14 (Test Nb Operating Thermal Shock)0 to 60degC (32 to 140degF)
storage temperature IEC 60068-2-1 (Test Ab Un-packaged Non-operating Cold)IEC 60068-2-2 (Test Bb Un-packaged Non-operating Dry Heat)IEC 60068-2-14 (Test Na Un-packaged Non-operating Thermal Shock)ndash40 to 85degC (ndash40 to 185degF)
relative humidity IEC 60068-2-30 (Test Db Un-packaged Non-operating Damp Heat)5 to 95 non-condensing
vibration(3) IEC60068-2-6 (Test Fc Operating) 5g 10-500Hz
shock(3)
operatingnon-operating
IEC60068-2-27 (Test Ea Unpackaged shock)
30g50g
emissions CISPR 11Group 1 Class A (with appropriate enclosure)
ESD immunity IEC 61000-4-26kV contact discharges8kV air discharges
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
RA-QR005C-EN-E 608
10 FlexLogix Controller System
Step 2 Install the Battery
For Safety information on the handling of lithium batteries including handling and disposal of leaking batteries see Guidelines for Handling Lithium Batteries publication AG 5-4
1 Install a 1756-BA1 battery
2 Attach the battery label
a Write on the battery label the date you install the battery
b Attach the label to the inside of the battery compartment
ATTENTION Only install a 1756-BA1 battery If you install a different battery you may damage the controller
WARNING For safety information on the handling of lithium batteries in-cluding the handling and disposal of leaking batteries see Guide-lines for Handling Lithium Batteries publication AG-54Store batteries in a cool dry environment We recommend 25degC with 40 to 60 relative humidity You may store batteries for up to 30 days between -45deg to 85degC such as during transporta-tion To avoid possible leakage do not store batteries above 60degC for more than 30 days
When you connect or disconnect the battery an electrical arc can occur This could cause an explosion in hazardous location in-stallations Be sure that power is removed or the area is nonhaz-ardous before proceeding
Attach battery here
top red lead (+)
middle black lead (-)
bottom no connection
Attach label here
This jumper is for service use only Do not use this jumper
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 11
Step 3 Install Communication Daughtercards (optional)
For specific information about configuring the communication card (such as setting a node address) see the installation instructions for the communication card
1 Turn off power to the controller
2 If necessary remove the blank cover from the communication slot
3 Slide the communication card into the communication slot Be sure to line up the card with the card guides in the controller
4 Record which slot you use for the communication card You need the slot number when you develop your controller application
5 Secure the card with the screws to ensure proper grounding Do not over-tighten the screws The maximum torque for the card screws is 48 to 52 inch pounds (05 to 06 Nm)
6 After the controller is installed (see page 12) connect the network cable
Removing a Communication CardIf you need to remove a communication card from the controller
1 Turn off power to the controller
2 Disconnect all cables from the communication card
3 Loosen the card screws from the communication card
4 Remove the card from the controller
5 Replace the card with a blank cover or a different communication card
WARNING If you insert or remove the card while host power is on an electrical arc can occur This could cause an explosion in haz-ardous location installations
31032-M
slot 1slot 2
Publication 1794-IN002G-EN-P - January 2004
12 FlexLogix Controller System
Step 4 Install the Controller
1 Position the FlexLogix controller on the DIN rail at a 5deg angle and rotate the controller onto the DIN rail
2 Press the controller down onto the DIN rail until flush The locking tabs will snap into position and lock the controller onto the DIN rail
If the controller does not lock in place use a screwdriver or similar device to move the locking tabs down while pressing the controller onto the DIN rail Release the locking tabs to lock the controller in place If necessary push up on the locking tabs to lock
3 Ground the controller The DIN rail and the common conductive surface behind the DIN rail provide functional ground for the controller Use the grounding stud to meet safety ground requirements
For information about wiring and grounding see the Industrial Automation Wiring and Grounding Guidelines publication 1770-41
IMPORTANT You can mount the FlexLogix controller either vertically or horizontally (as shown)
A
A
locking tabs
grounding stud
Equipment grounding conductor (ground lug with 208 sq mm [14 AWG] wire) to ground bus
nuts with captive star washer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 13
4 Make sure power is not applied to the power supply
5 Connect the power supply to the controller The graphic below and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the top of the controller connector terminal A to the bottom left power connector terminal G
b Connect -24V common to top controller connector terminal B to the top left power connector terminal E
c Use connections C and D on the controller and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the controller to meet the requirements for installations in Class I Division 2 locations
WARNING If you connect or disconnect wiring while the field-side power is on an electrical arc can occur This could cause an explosion in hazardous location installations Be sure that power is re-moved or the area is nonhazardous before proceeding
+
+
A
B
C
D
FE
HG
_
_
Publication 1794-IN002G-EN-P - January 2004
14 FlexLogix Controller System
6 Mount the IO terminal bases on the DIN rail
For information about IO terminal bases see the FLEX IO Terminal Base Installation Instructions publication 1794-IN092
7 Install the IO modules
To install an IO module see the installation instructions for that module
Removing the controllerIf you need to remove the controller follow these steps
1 Turn off power to the controller
2 Disconnect all cables from the controller
3 Remove the IO module that is adjacent to the controller
4 On the terminal base adjacent to the controller slide the FLEXBUS connector away from the controller and remove the IO terminal base
5 Remove the controller from the DIN rail
B
A
A
31036-M
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 15
Step 5 Install the Extended-Local Adapter (optional)
1 Position the 1794-FLA extended-local IO adapter on the DIN rail at a 30deg angle and rotate the adapter onto the DIN rail
2 Press the adapter down onto the DIN rail until flush The locking tab will snap into position and lock the adapter onto the DIN rail
If the adapter does not lock in place use a screwdriver or similar device to move the locking tab down while pressing the adapter onto the DIN rail Release the locking tab to lock the adapter in place If necessary push up on the locking tab to lock
3 Ground the adapter The adapter is grounded through the steel DIN rail and the common conductive surface behind the DIN rail Additionally use the grounding stud
grounding stud
Equipment grounding conductor (ground lug with 208 sq mm [14 AWG] wire) to ground bus
nuts with captive star washer
Publication 1794-IN002G-EN-P - January 2004
16 FlexLogix Controller System
4 Make sure power is not applied to the power supply Connect the power supply to the adapter This diagram and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the left adapter connector terminal A to the bottom left power connector terminal G
b Connect -24V common to left adapter connector terminal B to the top left power connector terminal E
c Use connections C and D on the adapter and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the adapter to meet the requirements for installations in Class I Division 2 locations
5 Connect IO terminal bases and IO modules to the adapter the same way you connect them to the controller
6 Remove the plastic spacer from both ends of the extended-local IO cable (1794-CE1 or 1794-CE3)
plastic spacer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 17
7 Connect the adapter to the controller
The following diagram shows how you can also use the 1794-CE1 -CE3 cable to split a rail of IO You can split each rail only once You can split a rail right after the controller (or adapter) or after any IO module For more information about the 1794-CE1 -CE3 cables see the Interconnect Cable Installation Instructions publication 1794-512
Removing the extended-local adapterIf you need to remove the adapter follow these steps
1 Turn off power to the adapter
2 Disconnect all cables from the adapter
3 Remove the IO module that is adjacent to the adapter
4 On the terminal base adjacent to the adapter slide the FLEXBUS connector away from the adapter and remove the IO terminal base
5 Remove the adapter from the DIN rail
31039-M
1794-CE1 or 1794-CE3 cable
LOCAL rail
LOCAL2 rail
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
Publication 1794-IN002G-EN-P - January 2004
18 FlexLogix Controller System
Make an RS-232 Connection to the ControllerThe RS-232 port is a non-isolated serial port built-in to the front of the controller
To connect to the serial port
1 Determine whether you need an optical isolator
If you connect the controller to a device outside of the systemrsquos enclosure consider installing an isolator between the controller and device
One possible isolator is the 1761-NET-AIC interface converter
serial port
port 1 DB-9 RS-232 DTE
baud rate selector switch
port 2 mini-DIN 8 RS-232
dc power source selector switch
terminals for external 24V dc power supply
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 19
2 Select the appropriate cable
Are you using an isolator
Use this cable
no The 1756-CP3 cable attaches the controller directly to the controller
If you make your own cable it must be shielded and the shields must be tied to the metal shell (that surrounds the pins) on both ends of the cableYou can also use a 1747-CP3 cable (from the SLC product family) This cable has a taller right-angle connector housing than the 1756-CP3 cable
yes The 1761-CBL-AP00 cable (right-angle connector to controller) or the 1761-CBL-PM02 cable (straight connector to the controller) attaches the controller to port 2 on the 1761-NET-AIC isolator The mini-DIN connector is not commercially available so you cannot make this cable
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
DB-9 right-angle or straight cable end 8-pin mini-DIN cable end
Pin DB-9 end Mini-DIN end1 DCD DCD
2 RxD RxD
3 TxD TxD
4 DTR DTR
5 ground ground
6 DSR DSR
7 RTS RTS
8 CTS CTS
9 na na
1 2
34
5
6 7867
8
9
1
2
3
4
5
Publication 1794-IN002G-EN-P - January 2004
20 FlexLogix Controller System
3 Connect the appropriate cable to the serial port on the controller
Be sure that power is removed or the area is nonhazardous before proceeding
4 If necessary attach the controller to the isolator
WARNING If you connect or disconnect the serial cable with power applied to this module or the serial device on the other end of the cable an electrical arc can occur This could cause an explosion in hazardous location installations
modem
1761-NET-AIC isolator
user-supplied modem cable
1761 cable
system enclosure
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 21
Select the Operating Mode of the Controller
1 Use this table to determine the operating mode of the controller
2 Turn the key on the front panel of the controller to select the mode
If you want to Select one of these modes
Run Program Remote
Run Program Test
turn outputs to the state commanded by the logic of the project
YES YES
turn outputs to their configured state for Program mode
YES YES YES
execute (scan) tasks YES YES YES
change the mode of the controller through software
YES YES YES
download a project YES YES
schedule a ControlNet network YES YES
while online edit the project YES YES YES YES
To select Turn the key to
Remote Run RUN and then to REM
Remote Program PROG and then to REM
Remote Test REM and then go online and select Test mode via the programming software
keyswitch
Publication 1794-IN002G-EN-P - January 2004
22 FlexLogix Controller System
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware RevisionTo update the firmware of a controller first install a firmware upgrade kit
bull An upgrade kit ships on a supplemental CD along with RSLogix 5000 software
bull To download an upgrade kit go to httpsupportrockwellautomationcom Choose Firmware Updates
Indicator Color Description
RUN off bull no task(s) running
bull controller in Program mode
green bull one or more tasks are running
bull controller is in Run mode
OK off no power applied
red flashing after initially installing the controller - the controller requires a FLASH upgrade to the proper firmware revision see belowafter the controller is operating - recoverable fault
red bull controller faulted
bull clear faults clear memory or replace the controller
green controller OK
BATTERY off battery will support memory
red bull battery may not support memory
bull replace battery
IO off bull controller project not downloaded (the condition after power up)
bull no IO or communications configured
green communicating to all devices
green flashing one or more devices are not responding
LOCALandLOCAL2
off rail is inhibited
green communicating to all devices on that rail
green flashing one or more devices on that rail not responding
red flashing no modules exist on that rail
RS232 off no activity
green data being received or transmitted
FORCE off no forces present
amber forces present
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 23
Update the Controller
1 Connect the controller to the same network as your workstation
2 Start ControlFLASH software
3 Choose Next gt
4 Select the catalog number of the controller and choose Next gt
5 Expand the network until you see the controller If the required network is not shown first configure a driver for the network in RSLinx software
6 Select the controller and choose OK
7 Select the revision level to which you want to update the controller and choose Next gt
8 To start the update of the controller choose Finish and then Yes
After the controller is updated the status box displays Update complete
9 Choose OK
10 To close ControlFLASH software choose Cancel and then Yes
TIP RSLogix 5000 software revision 100 or later lets you update controller firmware as part of the download sequence To update the controller download your project and follow the prompts of the software
IMPORTANT If the Revision list is empty download a new upgrade kit Some older upgrade kits do not work with new controllers
weight 1794-L33 71 kg (156 lbs oz)1794-L34 75 g (166 lbs)(no communication cards installed)
28 kg (62 lbs)
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 27
power supply 1794-PS3 or 1794-PS13 ndash In applications that must be compliant with CSA requirements use a Separated Extra-Low Voltage (SELV) power supply that is compliant with IEC 610101 Annex H
power conductors 60deg C (140deg F) minimum copper22 to 14 AWG (0324 to 208 sq mm) stranded364 inch (12mm) insulation maximumlength 10m or less
category 3(2)
power connector torque 5 to 7 inch-pounds (06 to 08Nm)
battery 1756-BA1 (AB part number 94194801)059g lithium
na
serial cable 1761-CBLPM02 to 1761-NET-AIC 1761-CBLPA00 to 1761-NET-AIC1756-CP3 directly to controller1747-CP3 directly to controller
DIN rail steel 35 x 755mm DIN railA-B part number 199-DR1 46277-3 EN 50022
operating temperature IEC 60068-2-1 (Test Ad Operating Cold)IEC 60068-2-2 (Test Bd Operating Dry Heat)IEC 60068-2-14 (Test Nb Operating Thermal Shock)0 to 60degC (32 to 140degF)
storage temperature IEC 60068-2-1 (Test Ab Un-packaged Non-operating Cold)IEC 60068-2-2 (Test Bb Un-packaged Non-operating Dry Heat)IEC 60068-2-14 (Test Na Un-packaged Non-operating Thermal Shock)ndash40 to 85degC (ndash40 to 185degF)
relative humidity IEC 60068-2-30 (Test Db Un-packaged Non-operating Damp Heat)5 to 95 non-condensing
vibration(3) IEC60068-2-6 (Test Fc Operating) 5g 10-500Hz
shock(3)
operatingnon-operating
IEC60068-2-27 (Test Ea Unpackaged shock)
30g50g
emissions CISPR 11Group 1 Class A (with appropriate enclosure)
ESD immunity IEC 61000-4-26kV contact discharges8kV air discharges
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
RA-QR005C-EN-E 608
FlexLogix Controller System 11
Step 3 Install Communication Daughtercards (optional)
For specific information about configuring the communication card (such as setting a node address) see the installation instructions for the communication card
1 Turn off power to the controller
2 If necessary remove the blank cover from the communication slot
3 Slide the communication card into the communication slot Be sure to line up the card with the card guides in the controller
4 Record which slot you use for the communication card You need the slot number when you develop your controller application
5 Secure the card with the screws to ensure proper grounding Do not over-tighten the screws The maximum torque for the card screws is 48 to 52 inch pounds (05 to 06 Nm)
6 After the controller is installed (see page 12) connect the network cable
Removing a Communication CardIf you need to remove a communication card from the controller
1 Turn off power to the controller
2 Disconnect all cables from the communication card
3 Loosen the card screws from the communication card
4 Remove the card from the controller
5 Replace the card with a blank cover or a different communication card
WARNING If you insert or remove the card while host power is on an electrical arc can occur This could cause an explosion in haz-ardous location installations
31032-M
slot 1slot 2
Publication 1794-IN002G-EN-P - January 2004
12 FlexLogix Controller System
Step 4 Install the Controller
1 Position the FlexLogix controller on the DIN rail at a 5deg angle and rotate the controller onto the DIN rail
2 Press the controller down onto the DIN rail until flush The locking tabs will snap into position and lock the controller onto the DIN rail
If the controller does not lock in place use a screwdriver or similar device to move the locking tabs down while pressing the controller onto the DIN rail Release the locking tabs to lock the controller in place If necessary push up on the locking tabs to lock
3 Ground the controller The DIN rail and the common conductive surface behind the DIN rail provide functional ground for the controller Use the grounding stud to meet safety ground requirements
For information about wiring and grounding see the Industrial Automation Wiring and Grounding Guidelines publication 1770-41
IMPORTANT You can mount the FlexLogix controller either vertically or horizontally (as shown)
A
A
locking tabs
grounding stud
Equipment grounding conductor (ground lug with 208 sq mm [14 AWG] wire) to ground bus
nuts with captive star washer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 13
4 Make sure power is not applied to the power supply
5 Connect the power supply to the controller The graphic below and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the top of the controller connector terminal A to the bottom left power connector terminal G
b Connect -24V common to top controller connector terminal B to the top left power connector terminal E
c Use connections C and D on the controller and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the controller to meet the requirements for installations in Class I Division 2 locations
WARNING If you connect or disconnect wiring while the field-side power is on an electrical arc can occur This could cause an explosion in hazardous location installations Be sure that power is re-moved or the area is nonhazardous before proceeding
+
+
A
B
C
D
FE
HG
_
_
Publication 1794-IN002G-EN-P - January 2004
14 FlexLogix Controller System
6 Mount the IO terminal bases on the DIN rail
For information about IO terminal bases see the FLEX IO Terminal Base Installation Instructions publication 1794-IN092
7 Install the IO modules
To install an IO module see the installation instructions for that module
Removing the controllerIf you need to remove the controller follow these steps
1 Turn off power to the controller
2 Disconnect all cables from the controller
3 Remove the IO module that is adjacent to the controller
4 On the terminal base adjacent to the controller slide the FLEXBUS connector away from the controller and remove the IO terminal base
5 Remove the controller from the DIN rail
B
A
A
31036-M
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 15
Step 5 Install the Extended-Local Adapter (optional)
1 Position the 1794-FLA extended-local IO adapter on the DIN rail at a 30deg angle and rotate the adapter onto the DIN rail
2 Press the adapter down onto the DIN rail until flush The locking tab will snap into position and lock the adapter onto the DIN rail
If the adapter does not lock in place use a screwdriver or similar device to move the locking tab down while pressing the adapter onto the DIN rail Release the locking tab to lock the adapter in place If necessary push up on the locking tab to lock
3 Ground the adapter The adapter is grounded through the steel DIN rail and the common conductive surface behind the DIN rail Additionally use the grounding stud
grounding stud
Equipment grounding conductor (ground lug with 208 sq mm [14 AWG] wire) to ground bus
nuts with captive star washer
Publication 1794-IN002G-EN-P - January 2004
16 FlexLogix Controller System
4 Make sure power is not applied to the power supply Connect the power supply to the adapter This diagram and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the left adapter connector terminal A to the bottom left power connector terminal G
b Connect -24V common to left adapter connector terminal B to the top left power connector terminal E
c Use connections C and D on the adapter and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the adapter to meet the requirements for installations in Class I Division 2 locations
5 Connect IO terminal bases and IO modules to the adapter the same way you connect them to the controller
6 Remove the plastic spacer from both ends of the extended-local IO cable (1794-CE1 or 1794-CE3)
plastic spacer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 17
7 Connect the adapter to the controller
The following diagram shows how you can also use the 1794-CE1 -CE3 cable to split a rail of IO You can split each rail only once You can split a rail right after the controller (or adapter) or after any IO module For more information about the 1794-CE1 -CE3 cables see the Interconnect Cable Installation Instructions publication 1794-512
Removing the extended-local adapterIf you need to remove the adapter follow these steps
1 Turn off power to the adapter
2 Disconnect all cables from the adapter
3 Remove the IO module that is adjacent to the adapter
4 On the terminal base adjacent to the adapter slide the FLEXBUS connector away from the adapter and remove the IO terminal base
5 Remove the adapter from the DIN rail
31039-M
1794-CE1 or 1794-CE3 cable
LOCAL rail
LOCAL2 rail
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
Publication 1794-IN002G-EN-P - January 2004
18 FlexLogix Controller System
Make an RS-232 Connection to the ControllerThe RS-232 port is a non-isolated serial port built-in to the front of the controller
To connect to the serial port
1 Determine whether you need an optical isolator
If you connect the controller to a device outside of the systemrsquos enclosure consider installing an isolator between the controller and device
One possible isolator is the 1761-NET-AIC interface converter
serial port
port 1 DB-9 RS-232 DTE
baud rate selector switch
port 2 mini-DIN 8 RS-232
dc power source selector switch
terminals for external 24V dc power supply
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 19
2 Select the appropriate cable
Are you using an isolator
Use this cable
no The 1756-CP3 cable attaches the controller directly to the controller
If you make your own cable it must be shielded and the shields must be tied to the metal shell (that surrounds the pins) on both ends of the cableYou can also use a 1747-CP3 cable (from the SLC product family) This cable has a taller right-angle connector housing than the 1756-CP3 cable
yes The 1761-CBL-AP00 cable (right-angle connector to controller) or the 1761-CBL-PM02 cable (straight connector to the controller) attaches the controller to port 2 on the 1761-NET-AIC isolator The mini-DIN connector is not commercially available so you cannot make this cable
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
DB-9 right-angle or straight cable end 8-pin mini-DIN cable end
Pin DB-9 end Mini-DIN end1 DCD DCD
2 RxD RxD
3 TxD TxD
4 DTR DTR
5 ground ground
6 DSR DSR
7 RTS RTS
8 CTS CTS
9 na na
1 2
34
5
6 7867
8
9
1
2
3
4
5
Publication 1794-IN002G-EN-P - January 2004
20 FlexLogix Controller System
3 Connect the appropriate cable to the serial port on the controller
Be sure that power is removed or the area is nonhazardous before proceeding
4 If necessary attach the controller to the isolator
WARNING If you connect or disconnect the serial cable with power applied to this module or the serial device on the other end of the cable an electrical arc can occur This could cause an explosion in hazardous location installations
modem
1761-NET-AIC isolator
user-supplied modem cable
1761 cable
system enclosure
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 21
Select the Operating Mode of the Controller
1 Use this table to determine the operating mode of the controller
2 Turn the key on the front panel of the controller to select the mode
If you want to Select one of these modes
Run Program Remote
Run Program Test
turn outputs to the state commanded by the logic of the project
YES YES
turn outputs to their configured state for Program mode
YES YES YES
execute (scan) tasks YES YES YES
change the mode of the controller through software
YES YES YES
download a project YES YES
schedule a ControlNet network YES YES
while online edit the project YES YES YES YES
To select Turn the key to
Remote Run RUN and then to REM
Remote Program PROG and then to REM
Remote Test REM and then go online and select Test mode via the programming software
keyswitch
Publication 1794-IN002G-EN-P - January 2004
22 FlexLogix Controller System
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware RevisionTo update the firmware of a controller first install a firmware upgrade kit
bull An upgrade kit ships on a supplemental CD along with RSLogix 5000 software
bull To download an upgrade kit go to httpsupportrockwellautomationcom Choose Firmware Updates
Indicator Color Description
RUN off bull no task(s) running
bull controller in Program mode
green bull one or more tasks are running
bull controller is in Run mode
OK off no power applied
red flashing after initially installing the controller - the controller requires a FLASH upgrade to the proper firmware revision see belowafter the controller is operating - recoverable fault
red bull controller faulted
bull clear faults clear memory or replace the controller
green controller OK
BATTERY off battery will support memory
red bull battery may not support memory
bull replace battery
IO off bull controller project not downloaded (the condition after power up)
bull no IO or communications configured
green communicating to all devices
green flashing one or more devices are not responding
LOCALandLOCAL2
off rail is inhibited
green communicating to all devices on that rail
green flashing one or more devices on that rail not responding
red flashing no modules exist on that rail
RS232 off no activity
green data being received or transmitted
FORCE off no forces present
amber forces present
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 23
Update the Controller
1 Connect the controller to the same network as your workstation
2 Start ControlFLASH software
3 Choose Next gt
4 Select the catalog number of the controller and choose Next gt
5 Expand the network until you see the controller If the required network is not shown first configure a driver for the network in RSLinx software
6 Select the controller and choose OK
7 Select the revision level to which you want to update the controller and choose Next gt
8 To start the update of the controller choose Finish and then Yes
After the controller is updated the status box displays Update complete
9 Choose OK
10 To close ControlFLASH software choose Cancel and then Yes
TIP RSLogix 5000 software revision 100 or later lets you update controller firmware as part of the download sequence To update the controller download your project and follow the prompts of the software
IMPORTANT If the Revision list is empty download a new upgrade kit Some older upgrade kits do not work with new controllers
weight 1794-L33 71 kg (156 lbs oz)1794-L34 75 g (166 lbs)(no communication cards installed)
28 kg (62 lbs)
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 27
power supply 1794-PS3 or 1794-PS13 ndash In applications that must be compliant with CSA requirements use a Separated Extra-Low Voltage (SELV) power supply that is compliant with IEC 610101 Annex H
power conductors 60deg C (140deg F) minimum copper22 to 14 AWG (0324 to 208 sq mm) stranded364 inch (12mm) insulation maximumlength 10m or less
category 3(2)
power connector torque 5 to 7 inch-pounds (06 to 08Nm)
battery 1756-BA1 (AB part number 94194801)059g lithium
na
serial cable 1761-CBLPM02 to 1761-NET-AIC 1761-CBLPA00 to 1761-NET-AIC1756-CP3 directly to controller1747-CP3 directly to controller
DIN rail steel 35 x 755mm DIN railA-B part number 199-DR1 46277-3 EN 50022
operating temperature IEC 60068-2-1 (Test Ad Operating Cold)IEC 60068-2-2 (Test Bd Operating Dry Heat)IEC 60068-2-14 (Test Nb Operating Thermal Shock)0 to 60degC (32 to 140degF)
storage temperature IEC 60068-2-1 (Test Ab Un-packaged Non-operating Cold)IEC 60068-2-2 (Test Bb Un-packaged Non-operating Dry Heat)IEC 60068-2-14 (Test Na Un-packaged Non-operating Thermal Shock)ndash40 to 85degC (ndash40 to 185degF)
relative humidity IEC 60068-2-30 (Test Db Un-packaged Non-operating Damp Heat)5 to 95 non-condensing
vibration(3) IEC60068-2-6 (Test Fc Operating) 5g 10-500Hz
shock(3)
operatingnon-operating
IEC60068-2-27 (Test Ea Unpackaged shock)
30g50g
emissions CISPR 11Group 1 Class A (with appropriate enclosure)
ESD immunity IEC 61000-4-26kV contact discharges8kV air discharges
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
RA-QR005C-EN-E 608
12 FlexLogix Controller System
Step 4 Install the Controller
1 Position the FlexLogix controller on the DIN rail at a 5deg angle and rotate the controller onto the DIN rail
2 Press the controller down onto the DIN rail until flush The locking tabs will snap into position and lock the controller onto the DIN rail
If the controller does not lock in place use a screwdriver or similar device to move the locking tabs down while pressing the controller onto the DIN rail Release the locking tabs to lock the controller in place If necessary push up on the locking tabs to lock
3 Ground the controller The DIN rail and the common conductive surface behind the DIN rail provide functional ground for the controller Use the grounding stud to meet safety ground requirements
For information about wiring and grounding see the Industrial Automation Wiring and Grounding Guidelines publication 1770-41
IMPORTANT You can mount the FlexLogix controller either vertically or horizontally (as shown)
A
A
locking tabs
grounding stud
Equipment grounding conductor (ground lug with 208 sq mm [14 AWG] wire) to ground bus
nuts with captive star washer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 13
4 Make sure power is not applied to the power supply
5 Connect the power supply to the controller The graphic below and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the top of the controller connector terminal A to the bottom left power connector terminal G
b Connect -24V common to top controller connector terminal B to the top left power connector terminal E
c Use connections C and D on the controller and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the controller to meet the requirements for installations in Class I Division 2 locations
WARNING If you connect or disconnect wiring while the field-side power is on an electrical arc can occur This could cause an explosion in hazardous location installations Be sure that power is re-moved or the area is nonhazardous before proceeding
+
+
A
B
C
D
FE
HG
_
_
Publication 1794-IN002G-EN-P - January 2004
14 FlexLogix Controller System
6 Mount the IO terminal bases on the DIN rail
For information about IO terminal bases see the FLEX IO Terminal Base Installation Instructions publication 1794-IN092
7 Install the IO modules
To install an IO module see the installation instructions for that module
Removing the controllerIf you need to remove the controller follow these steps
1 Turn off power to the controller
2 Disconnect all cables from the controller
3 Remove the IO module that is adjacent to the controller
4 On the terminal base adjacent to the controller slide the FLEXBUS connector away from the controller and remove the IO terminal base
5 Remove the controller from the DIN rail
B
A
A
31036-M
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 15
Step 5 Install the Extended-Local Adapter (optional)
1 Position the 1794-FLA extended-local IO adapter on the DIN rail at a 30deg angle and rotate the adapter onto the DIN rail
2 Press the adapter down onto the DIN rail until flush The locking tab will snap into position and lock the adapter onto the DIN rail
If the adapter does not lock in place use a screwdriver or similar device to move the locking tab down while pressing the adapter onto the DIN rail Release the locking tab to lock the adapter in place If necessary push up on the locking tab to lock
3 Ground the adapter The adapter is grounded through the steel DIN rail and the common conductive surface behind the DIN rail Additionally use the grounding stud
grounding stud
Equipment grounding conductor (ground lug with 208 sq mm [14 AWG] wire) to ground bus
nuts with captive star washer
Publication 1794-IN002G-EN-P - January 2004
16 FlexLogix Controller System
4 Make sure power is not applied to the power supply Connect the power supply to the adapter This diagram and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the left adapter connector terminal A to the bottom left power connector terminal G
b Connect -24V common to left adapter connector terminal B to the top left power connector terminal E
c Use connections C and D on the adapter and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the adapter to meet the requirements for installations in Class I Division 2 locations
5 Connect IO terminal bases and IO modules to the adapter the same way you connect them to the controller
6 Remove the plastic spacer from both ends of the extended-local IO cable (1794-CE1 or 1794-CE3)
plastic spacer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 17
7 Connect the adapter to the controller
The following diagram shows how you can also use the 1794-CE1 -CE3 cable to split a rail of IO You can split each rail only once You can split a rail right after the controller (or adapter) or after any IO module For more information about the 1794-CE1 -CE3 cables see the Interconnect Cable Installation Instructions publication 1794-512
Removing the extended-local adapterIf you need to remove the adapter follow these steps
1 Turn off power to the adapter
2 Disconnect all cables from the adapter
3 Remove the IO module that is adjacent to the adapter
4 On the terminal base adjacent to the adapter slide the FLEXBUS connector away from the adapter and remove the IO terminal base
5 Remove the adapter from the DIN rail
31039-M
1794-CE1 or 1794-CE3 cable
LOCAL rail
LOCAL2 rail
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
Publication 1794-IN002G-EN-P - January 2004
18 FlexLogix Controller System
Make an RS-232 Connection to the ControllerThe RS-232 port is a non-isolated serial port built-in to the front of the controller
To connect to the serial port
1 Determine whether you need an optical isolator
If you connect the controller to a device outside of the systemrsquos enclosure consider installing an isolator between the controller and device
One possible isolator is the 1761-NET-AIC interface converter
serial port
port 1 DB-9 RS-232 DTE
baud rate selector switch
port 2 mini-DIN 8 RS-232
dc power source selector switch
terminals for external 24V dc power supply
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 19
2 Select the appropriate cable
Are you using an isolator
Use this cable
no The 1756-CP3 cable attaches the controller directly to the controller
If you make your own cable it must be shielded and the shields must be tied to the metal shell (that surrounds the pins) on both ends of the cableYou can also use a 1747-CP3 cable (from the SLC product family) This cable has a taller right-angle connector housing than the 1756-CP3 cable
yes The 1761-CBL-AP00 cable (right-angle connector to controller) or the 1761-CBL-PM02 cable (straight connector to the controller) attaches the controller to port 2 on the 1761-NET-AIC isolator The mini-DIN connector is not commercially available so you cannot make this cable
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
DB-9 right-angle or straight cable end 8-pin mini-DIN cable end
Pin DB-9 end Mini-DIN end1 DCD DCD
2 RxD RxD
3 TxD TxD
4 DTR DTR
5 ground ground
6 DSR DSR
7 RTS RTS
8 CTS CTS
9 na na
1 2
34
5
6 7867
8
9
1
2
3
4
5
Publication 1794-IN002G-EN-P - January 2004
20 FlexLogix Controller System
3 Connect the appropriate cable to the serial port on the controller
Be sure that power is removed or the area is nonhazardous before proceeding
4 If necessary attach the controller to the isolator
WARNING If you connect or disconnect the serial cable with power applied to this module or the serial device on the other end of the cable an electrical arc can occur This could cause an explosion in hazardous location installations
modem
1761-NET-AIC isolator
user-supplied modem cable
1761 cable
system enclosure
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 21
Select the Operating Mode of the Controller
1 Use this table to determine the operating mode of the controller
2 Turn the key on the front panel of the controller to select the mode
If you want to Select one of these modes
Run Program Remote
Run Program Test
turn outputs to the state commanded by the logic of the project
YES YES
turn outputs to their configured state for Program mode
YES YES YES
execute (scan) tasks YES YES YES
change the mode of the controller through software
YES YES YES
download a project YES YES
schedule a ControlNet network YES YES
while online edit the project YES YES YES YES
To select Turn the key to
Remote Run RUN and then to REM
Remote Program PROG and then to REM
Remote Test REM and then go online and select Test mode via the programming software
keyswitch
Publication 1794-IN002G-EN-P - January 2004
22 FlexLogix Controller System
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware RevisionTo update the firmware of a controller first install a firmware upgrade kit
bull An upgrade kit ships on a supplemental CD along with RSLogix 5000 software
bull To download an upgrade kit go to httpsupportrockwellautomationcom Choose Firmware Updates
Indicator Color Description
RUN off bull no task(s) running
bull controller in Program mode
green bull one or more tasks are running
bull controller is in Run mode
OK off no power applied
red flashing after initially installing the controller - the controller requires a FLASH upgrade to the proper firmware revision see belowafter the controller is operating - recoverable fault
red bull controller faulted
bull clear faults clear memory or replace the controller
green controller OK
BATTERY off battery will support memory
red bull battery may not support memory
bull replace battery
IO off bull controller project not downloaded (the condition after power up)
bull no IO or communications configured
green communicating to all devices
green flashing one or more devices are not responding
LOCALandLOCAL2
off rail is inhibited
green communicating to all devices on that rail
green flashing one or more devices on that rail not responding
red flashing no modules exist on that rail
RS232 off no activity
green data being received or transmitted
FORCE off no forces present
amber forces present
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 23
Update the Controller
1 Connect the controller to the same network as your workstation
2 Start ControlFLASH software
3 Choose Next gt
4 Select the catalog number of the controller and choose Next gt
5 Expand the network until you see the controller If the required network is not shown first configure a driver for the network in RSLinx software
6 Select the controller and choose OK
7 Select the revision level to which you want to update the controller and choose Next gt
8 To start the update of the controller choose Finish and then Yes
After the controller is updated the status box displays Update complete
9 Choose OK
10 To close ControlFLASH software choose Cancel and then Yes
TIP RSLogix 5000 software revision 100 or later lets you update controller firmware as part of the download sequence To update the controller download your project and follow the prompts of the software
IMPORTANT If the Revision list is empty download a new upgrade kit Some older upgrade kits do not work with new controllers
weight 1794-L33 71 kg (156 lbs oz)1794-L34 75 g (166 lbs)(no communication cards installed)
28 kg (62 lbs)
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 27
power supply 1794-PS3 or 1794-PS13 ndash In applications that must be compliant with CSA requirements use a Separated Extra-Low Voltage (SELV) power supply that is compliant with IEC 610101 Annex H
power conductors 60deg C (140deg F) minimum copper22 to 14 AWG (0324 to 208 sq mm) stranded364 inch (12mm) insulation maximumlength 10m or less
category 3(2)
power connector torque 5 to 7 inch-pounds (06 to 08Nm)
battery 1756-BA1 (AB part number 94194801)059g lithium
na
serial cable 1761-CBLPM02 to 1761-NET-AIC 1761-CBLPA00 to 1761-NET-AIC1756-CP3 directly to controller1747-CP3 directly to controller
DIN rail steel 35 x 755mm DIN railA-B part number 199-DR1 46277-3 EN 50022
operating temperature IEC 60068-2-1 (Test Ad Operating Cold)IEC 60068-2-2 (Test Bd Operating Dry Heat)IEC 60068-2-14 (Test Nb Operating Thermal Shock)0 to 60degC (32 to 140degF)
storage temperature IEC 60068-2-1 (Test Ab Un-packaged Non-operating Cold)IEC 60068-2-2 (Test Bb Un-packaged Non-operating Dry Heat)IEC 60068-2-14 (Test Na Un-packaged Non-operating Thermal Shock)ndash40 to 85degC (ndash40 to 185degF)
relative humidity IEC 60068-2-30 (Test Db Un-packaged Non-operating Damp Heat)5 to 95 non-condensing
vibration(3) IEC60068-2-6 (Test Fc Operating) 5g 10-500Hz
shock(3)
operatingnon-operating
IEC60068-2-27 (Test Ea Unpackaged shock)
30g50g
emissions CISPR 11Group 1 Class A (with appropriate enclosure)
ESD immunity IEC 61000-4-26kV contact discharges8kV air discharges
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
RA-QR005C-EN-E 608
FlexLogix Controller System 13
4 Make sure power is not applied to the power supply
5 Connect the power supply to the controller The graphic below and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the top of the controller connector terminal A to the bottom left power connector terminal G
b Connect -24V common to top controller connector terminal B to the top left power connector terminal E
c Use connections C and D on the controller and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the controller to meet the requirements for installations in Class I Division 2 locations
WARNING If you connect or disconnect wiring while the field-side power is on an electrical arc can occur This could cause an explosion in hazardous location installations Be sure that power is re-moved or the area is nonhazardous before proceeding
+
+
A
B
C
D
FE
HG
_
_
Publication 1794-IN002G-EN-P - January 2004
14 FlexLogix Controller System
6 Mount the IO terminal bases on the DIN rail
For information about IO terminal bases see the FLEX IO Terminal Base Installation Instructions publication 1794-IN092
7 Install the IO modules
To install an IO module see the installation instructions for that module
Removing the controllerIf you need to remove the controller follow these steps
1 Turn off power to the controller
2 Disconnect all cables from the controller
3 Remove the IO module that is adjacent to the controller
4 On the terminal base adjacent to the controller slide the FLEXBUS connector away from the controller and remove the IO terminal base
5 Remove the controller from the DIN rail
B
A
A
31036-M
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 15
Step 5 Install the Extended-Local Adapter (optional)
1 Position the 1794-FLA extended-local IO adapter on the DIN rail at a 30deg angle and rotate the adapter onto the DIN rail
2 Press the adapter down onto the DIN rail until flush The locking tab will snap into position and lock the adapter onto the DIN rail
If the adapter does not lock in place use a screwdriver or similar device to move the locking tab down while pressing the adapter onto the DIN rail Release the locking tab to lock the adapter in place If necessary push up on the locking tab to lock
3 Ground the adapter The adapter is grounded through the steel DIN rail and the common conductive surface behind the DIN rail Additionally use the grounding stud
grounding stud
Equipment grounding conductor (ground lug with 208 sq mm [14 AWG] wire) to ground bus
nuts with captive star washer
Publication 1794-IN002G-EN-P - January 2004
16 FlexLogix Controller System
4 Make sure power is not applied to the power supply Connect the power supply to the adapter This diagram and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the left adapter connector terminal A to the bottom left power connector terminal G
b Connect -24V common to left adapter connector terminal B to the top left power connector terminal E
c Use connections C and D on the adapter and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the adapter to meet the requirements for installations in Class I Division 2 locations
5 Connect IO terminal bases and IO modules to the adapter the same way you connect them to the controller
6 Remove the plastic spacer from both ends of the extended-local IO cable (1794-CE1 or 1794-CE3)
plastic spacer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 17
7 Connect the adapter to the controller
The following diagram shows how you can also use the 1794-CE1 -CE3 cable to split a rail of IO You can split each rail only once You can split a rail right after the controller (or adapter) or after any IO module For more information about the 1794-CE1 -CE3 cables see the Interconnect Cable Installation Instructions publication 1794-512
Removing the extended-local adapterIf you need to remove the adapter follow these steps
1 Turn off power to the adapter
2 Disconnect all cables from the adapter
3 Remove the IO module that is adjacent to the adapter
4 On the terminal base adjacent to the adapter slide the FLEXBUS connector away from the adapter and remove the IO terminal base
5 Remove the adapter from the DIN rail
31039-M
1794-CE1 or 1794-CE3 cable
LOCAL rail
LOCAL2 rail
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
Publication 1794-IN002G-EN-P - January 2004
18 FlexLogix Controller System
Make an RS-232 Connection to the ControllerThe RS-232 port is a non-isolated serial port built-in to the front of the controller
To connect to the serial port
1 Determine whether you need an optical isolator
If you connect the controller to a device outside of the systemrsquos enclosure consider installing an isolator between the controller and device
One possible isolator is the 1761-NET-AIC interface converter
serial port
port 1 DB-9 RS-232 DTE
baud rate selector switch
port 2 mini-DIN 8 RS-232
dc power source selector switch
terminals for external 24V dc power supply
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 19
2 Select the appropriate cable
Are you using an isolator
Use this cable
no The 1756-CP3 cable attaches the controller directly to the controller
If you make your own cable it must be shielded and the shields must be tied to the metal shell (that surrounds the pins) on both ends of the cableYou can also use a 1747-CP3 cable (from the SLC product family) This cable has a taller right-angle connector housing than the 1756-CP3 cable
yes The 1761-CBL-AP00 cable (right-angle connector to controller) or the 1761-CBL-PM02 cable (straight connector to the controller) attaches the controller to port 2 on the 1761-NET-AIC isolator The mini-DIN connector is not commercially available so you cannot make this cable
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
DB-9 right-angle or straight cable end 8-pin mini-DIN cable end
Pin DB-9 end Mini-DIN end1 DCD DCD
2 RxD RxD
3 TxD TxD
4 DTR DTR
5 ground ground
6 DSR DSR
7 RTS RTS
8 CTS CTS
9 na na
1 2
34
5
6 7867
8
9
1
2
3
4
5
Publication 1794-IN002G-EN-P - January 2004
20 FlexLogix Controller System
3 Connect the appropriate cable to the serial port on the controller
Be sure that power is removed or the area is nonhazardous before proceeding
4 If necessary attach the controller to the isolator
WARNING If you connect or disconnect the serial cable with power applied to this module or the serial device on the other end of the cable an electrical arc can occur This could cause an explosion in hazardous location installations
modem
1761-NET-AIC isolator
user-supplied modem cable
1761 cable
system enclosure
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 21
Select the Operating Mode of the Controller
1 Use this table to determine the operating mode of the controller
2 Turn the key on the front panel of the controller to select the mode
If you want to Select one of these modes
Run Program Remote
Run Program Test
turn outputs to the state commanded by the logic of the project
YES YES
turn outputs to their configured state for Program mode
YES YES YES
execute (scan) tasks YES YES YES
change the mode of the controller through software
YES YES YES
download a project YES YES
schedule a ControlNet network YES YES
while online edit the project YES YES YES YES
To select Turn the key to
Remote Run RUN and then to REM
Remote Program PROG and then to REM
Remote Test REM and then go online and select Test mode via the programming software
keyswitch
Publication 1794-IN002G-EN-P - January 2004
22 FlexLogix Controller System
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware RevisionTo update the firmware of a controller first install a firmware upgrade kit
bull An upgrade kit ships on a supplemental CD along with RSLogix 5000 software
bull To download an upgrade kit go to httpsupportrockwellautomationcom Choose Firmware Updates
Indicator Color Description
RUN off bull no task(s) running
bull controller in Program mode
green bull one or more tasks are running
bull controller is in Run mode
OK off no power applied
red flashing after initially installing the controller - the controller requires a FLASH upgrade to the proper firmware revision see belowafter the controller is operating - recoverable fault
red bull controller faulted
bull clear faults clear memory or replace the controller
green controller OK
BATTERY off battery will support memory
red bull battery may not support memory
bull replace battery
IO off bull controller project not downloaded (the condition after power up)
bull no IO or communications configured
green communicating to all devices
green flashing one or more devices are not responding
LOCALandLOCAL2
off rail is inhibited
green communicating to all devices on that rail
green flashing one or more devices on that rail not responding
red flashing no modules exist on that rail
RS232 off no activity
green data being received or transmitted
FORCE off no forces present
amber forces present
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 23
Update the Controller
1 Connect the controller to the same network as your workstation
2 Start ControlFLASH software
3 Choose Next gt
4 Select the catalog number of the controller and choose Next gt
5 Expand the network until you see the controller If the required network is not shown first configure a driver for the network in RSLinx software
6 Select the controller and choose OK
7 Select the revision level to which you want to update the controller and choose Next gt
8 To start the update of the controller choose Finish and then Yes
After the controller is updated the status box displays Update complete
9 Choose OK
10 To close ControlFLASH software choose Cancel and then Yes
TIP RSLogix 5000 software revision 100 or later lets you update controller firmware as part of the download sequence To update the controller download your project and follow the prompts of the software
IMPORTANT If the Revision list is empty download a new upgrade kit Some older upgrade kits do not work with new controllers
weight 1794-L33 71 kg (156 lbs oz)1794-L34 75 g (166 lbs)(no communication cards installed)
28 kg (62 lbs)
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 27
power supply 1794-PS3 or 1794-PS13 ndash In applications that must be compliant with CSA requirements use a Separated Extra-Low Voltage (SELV) power supply that is compliant with IEC 610101 Annex H
power conductors 60deg C (140deg F) minimum copper22 to 14 AWG (0324 to 208 sq mm) stranded364 inch (12mm) insulation maximumlength 10m or less
category 3(2)
power connector torque 5 to 7 inch-pounds (06 to 08Nm)
battery 1756-BA1 (AB part number 94194801)059g lithium
na
serial cable 1761-CBLPM02 to 1761-NET-AIC 1761-CBLPA00 to 1761-NET-AIC1756-CP3 directly to controller1747-CP3 directly to controller
DIN rail steel 35 x 755mm DIN railA-B part number 199-DR1 46277-3 EN 50022
operating temperature IEC 60068-2-1 (Test Ad Operating Cold)IEC 60068-2-2 (Test Bd Operating Dry Heat)IEC 60068-2-14 (Test Nb Operating Thermal Shock)0 to 60degC (32 to 140degF)
storage temperature IEC 60068-2-1 (Test Ab Un-packaged Non-operating Cold)IEC 60068-2-2 (Test Bb Un-packaged Non-operating Dry Heat)IEC 60068-2-14 (Test Na Un-packaged Non-operating Thermal Shock)ndash40 to 85degC (ndash40 to 185degF)
relative humidity IEC 60068-2-30 (Test Db Un-packaged Non-operating Damp Heat)5 to 95 non-condensing
vibration(3) IEC60068-2-6 (Test Fc Operating) 5g 10-500Hz
shock(3)
operatingnon-operating
IEC60068-2-27 (Test Ea Unpackaged shock)
30g50g
emissions CISPR 11Group 1 Class A (with appropriate enclosure)
ESD immunity IEC 61000-4-26kV contact discharges8kV air discharges
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
RA-QR005C-EN-E 608
14 FlexLogix Controller System
6 Mount the IO terminal bases on the DIN rail
For information about IO terminal bases see the FLEX IO Terminal Base Installation Instructions publication 1794-IN092
7 Install the IO modules
To install an IO module see the installation instructions for that module
Removing the controllerIf you need to remove the controller follow these steps
1 Turn off power to the controller
2 Disconnect all cables from the controller
3 Remove the IO module that is adjacent to the controller
4 On the terminal base adjacent to the controller slide the FLEXBUS connector away from the controller and remove the IO terminal base
5 Remove the controller from the DIN rail
B
A
A
31036-M
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 15
Step 5 Install the Extended-Local Adapter (optional)
1 Position the 1794-FLA extended-local IO adapter on the DIN rail at a 30deg angle and rotate the adapter onto the DIN rail
2 Press the adapter down onto the DIN rail until flush The locking tab will snap into position and lock the adapter onto the DIN rail
If the adapter does not lock in place use a screwdriver or similar device to move the locking tab down while pressing the adapter onto the DIN rail Release the locking tab to lock the adapter in place If necessary push up on the locking tab to lock
3 Ground the adapter The adapter is grounded through the steel DIN rail and the common conductive surface behind the DIN rail Additionally use the grounding stud
grounding stud
Equipment grounding conductor (ground lug with 208 sq mm [14 AWG] wire) to ground bus
nuts with captive star washer
Publication 1794-IN002G-EN-P - January 2004
16 FlexLogix Controller System
4 Make sure power is not applied to the power supply Connect the power supply to the adapter This diagram and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the left adapter connector terminal A to the bottom left power connector terminal G
b Connect -24V common to left adapter connector terminal B to the top left power connector terminal E
c Use connections C and D on the adapter and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the adapter to meet the requirements for installations in Class I Division 2 locations
5 Connect IO terminal bases and IO modules to the adapter the same way you connect them to the controller
6 Remove the plastic spacer from both ends of the extended-local IO cable (1794-CE1 or 1794-CE3)
plastic spacer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 17
7 Connect the adapter to the controller
The following diagram shows how you can also use the 1794-CE1 -CE3 cable to split a rail of IO You can split each rail only once You can split a rail right after the controller (or adapter) or after any IO module For more information about the 1794-CE1 -CE3 cables see the Interconnect Cable Installation Instructions publication 1794-512
Removing the extended-local adapterIf you need to remove the adapter follow these steps
1 Turn off power to the adapter
2 Disconnect all cables from the adapter
3 Remove the IO module that is adjacent to the adapter
4 On the terminal base adjacent to the adapter slide the FLEXBUS connector away from the adapter and remove the IO terminal base
5 Remove the adapter from the DIN rail
31039-M
1794-CE1 or 1794-CE3 cable
LOCAL rail
LOCAL2 rail
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
Publication 1794-IN002G-EN-P - January 2004
18 FlexLogix Controller System
Make an RS-232 Connection to the ControllerThe RS-232 port is a non-isolated serial port built-in to the front of the controller
To connect to the serial port
1 Determine whether you need an optical isolator
If you connect the controller to a device outside of the systemrsquos enclosure consider installing an isolator between the controller and device
One possible isolator is the 1761-NET-AIC interface converter
serial port
port 1 DB-9 RS-232 DTE
baud rate selector switch
port 2 mini-DIN 8 RS-232
dc power source selector switch
terminals for external 24V dc power supply
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 19
2 Select the appropriate cable
Are you using an isolator
Use this cable
no The 1756-CP3 cable attaches the controller directly to the controller
If you make your own cable it must be shielded and the shields must be tied to the metal shell (that surrounds the pins) on both ends of the cableYou can also use a 1747-CP3 cable (from the SLC product family) This cable has a taller right-angle connector housing than the 1756-CP3 cable
yes The 1761-CBL-AP00 cable (right-angle connector to controller) or the 1761-CBL-PM02 cable (straight connector to the controller) attaches the controller to port 2 on the 1761-NET-AIC isolator The mini-DIN connector is not commercially available so you cannot make this cable
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
DB-9 right-angle or straight cable end 8-pin mini-DIN cable end
Pin DB-9 end Mini-DIN end1 DCD DCD
2 RxD RxD
3 TxD TxD
4 DTR DTR
5 ground ground
6 DSR DSR
7 RTS RTS
8 CTS CTS
9 na na
1 2
34
5
6 7867
8
9
1
2
3
4
5
Publication 1794-IN002G-EN-P - January 2004
20 FlexLogix Controller System
3 Connect the appropriate cable to the serial port on the controller
Be sure that power is removed or the area is nonhazardous before proceeding
4 If necessary attach the controller to the isolator
WARNING If you connect or disconnect the serial cable with power applied to this module or the serial device on the other end of the cable an electrical arc can occur This could cause an explosion in hazardous location installations
modem
1761-NET-AIC isolator
user-supplied modem cable
1761 cable
system enclosure
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 21
Select the Operating Mode of the Controller
1 Use this table to determine the operating mode of the controller
2 Turn the key on the front panel of the controller to select the mode
If you want to Select one of these modes
Run Program Remote
Run Program Test
turn outputs to the state commanded by the logic of the project
YES YES
turn outputs to their configured state for Program mode
YES YES YES
execute (scan) tasks YES YES YES
change the mode of the controller through software
YES YES YES
download a project YES YES
schedule a ControlNet network YES YES
while online edit the project YES YES YES YES
To select Turn the key to
Remote Run RUN and then to REM
Remote Program PROG and then to REM
Remote Test REM and then go online and select Test mode via the programming software
keyswitch
Publication 1794-IN002G-EN-P - January 2004
22 FlexLogix Controller System
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware RevisionTo update the firmware of a controller first install a firmware upgrade kit
bull An upgrade kit ships on a supplemental CD along with RSLogix 5000 software
bull To download an upgrade kit go to httpsupportrockwellautomationcom Choose Firmware Updates
Indicator Color Description
RUN off bull no task(s) running
bull controller in Program mode
green bull one or more tasks are running
bull controller is in Run mode
OK off no power applied
red flashing after initially installing the controller - the controller requires a FLASH upgrade to the proper firmware revision see belowafter the controller is operating - recoverable fault
red bull controller faulted
bull clear faults clear memory or replace the controller
green controller OK
BATTERY off battery will support memory
red bull battery may not support memory
bull replace battery
IO off bull controller project not downloaded (the condition after power up)
bull no IO or communications configured
green communicating to all devices
green flashing one or more devices are not responding
LOCALandLOCAL2
off rail is inhibited
green communicating to all devices on that rail
green flashing one or more devices on that rail not responding
red flashing no modules exist on that rail
RS232 off no activity
green data being received or transmitted
FORCE off no forces present
amber forces present
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 23
Update the Controller
1 Connect the controller to the same network as your workstation
2 Start ControlFLASH software
3 Choose Next gt
4 Select the catalog number of the controller and choose Next gt
5 Expand the network until you see the controller If the required network is not shown first configure a driver for the network in RSLinx software
6 Select the controller and choose OK
7 Select the revision level to which you want to update the controller and choose Next gt
8 To start the update of the controller choose Finish and then Yes
After the controller is updated the status box displays Update complete
9 Choose OK
10 To close ControlFLASH software choose Cancel and then Yes
TIP RSLogix 5000 software revision 100 or later lets you update controller firmware as part of the download sequence To update the controller download your project and follow the prompts of the software
IMPORTANT If the Revision list is empty download a new upgrade kit Some older upgrade kits do not work with new controllers
weight 1794-L33 71 kg (156 lbs oz)1794-L34 75 g (166 lbs)(no communication cards installed)
28 kg (62 lbs)
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 27
power supply 1794-PS3 or 1794-PS13 ndash In applications that must be compliant with CSA requirements use a Separated Extra-Low Voltage (SELV) power supply that is compliant with IEC 610101 Annex H
power conductors 60deg C (140deg F) minimum copper22 to 14 AWG (0324 to 208 sq mm) stranded364 inch (12mm) insulation maximumlength 10m or less
category 3(2)
power connector torque 5 to 7 inch-pounds (06 to 08Nm)
battery 1756-BA1 (AB part number 94194801)059g lithium
na
serial cable 1761-CBLPM02 to 1761-NET-AIC 1761-CBLPA00 to 1761-NET-AIC1756-CP3 directly to controller1747-CP3 directly to controller
DIN rail steel 35 x 755mm DIN railA-B part number 199-DR1 46277-3 EN 50022
operating temperature IEC 60068-2-1 (Test Ad Operating Cold)IEC 60068-2-2 (Test Bd Operating Dry Heat)IEC 60068-2-14 (Test Nb Operating Thermal Shock)0 to 60degC (32 to 140degF)
storage temperature IEC 60068-2-1 (Test Ab Un-packaged Non-operating Cold)IEC 60068-2-2 (Test Bb Un-packaged Non-operating Dry Heat)IEC 60068-2-14 (Test Na Un-packaged Non-operating Thermal Shock)ndash40 to 85degC (ndash40 to 185degF)
relative humidity IEC 60068-2-30 (Test Db Un-packaged Non-operating Damp Heat)5 to 95 non-condensing
vibration(3) IEC60068-2-6 (Test Fc Operating) 5g 10-500Hz
shock(3)
operatingnon-operating
IEC60068-2-27 (Test Ea Unpackaged shock)
30g50g
emissions CISPR 11Group 1 Class A (with appropriate enclosure)
ESD immunity IEC 61000-4-26kV contact discharges8kV air discharges
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
RA-QR005C-EN-E 608
FlexLogix Controller System 15
Step 5 Install the Extended-Local Adapter (optional)
1 Position the 1794-FLA extended-local IO adapter on the DIN rail at a 30deg angle and rotate the adapter onto the DIN rail
2 Press the adapter down onto the DIN rail until flush The locking tab will snap into position and lock the adapter onto the DIN rail
If the adapter does not lock in place use a screwdriver or similar device to move the locking tab down while pressing the adapter onto the DIN rail Release the locking tab to lock the adapter in place If necessary push up on the locking tab to lock
3 Ground the adapter The adapter is grounded through the steel DIN rail and the common conductive surface behind the DIN rail Additionally use the grounding stud
grounding stud
Equipment grounding conductor (ground lug with 208 sq mm [14 AWG] wire) to ground bus
nuts with captive star washer
Publication 1794-IN002G-EN-P - January 2004
16 FlexLogix Controller System
4 Make sure power is not applied to the power supply Connect the power supply to the adapter This diagram and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the left adapter connector terminal A to the bottom left power connector terminal G
b Connect -24V common to left adapter connector terminal B to the top left power connector terminal E
c Use connections C and D on the adapter and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the adapter to meet the requirements for installations in Class I Division 2 locations
5 Connect IO terminal bases and IO modules to the adapter the same way you connect them to the controller
6 Remove the plastic spacer from both ends of the extended-local IO cable (1794-CE1 or 1794-CE3)
plastic spacer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 17
7 Connect the adapter to the controller
The following diagram shows how you can also use the 1794-CE1 -CE3 cable to split a rail of IO You can split each rail only once You can split a rail right after the controller (or adapter) or after any IO module For more information about the 1794-CE1 -CE3 cables see the Interconnect Cable Installation Instructions publication 1794-512
Removing the extended-local adapterIf you need to remove the adapter follow these steps
1 Turn off power to the adapter
2 Disconnect all cables from the adapter
3 Remove the IO module that is adjacent to the adapter
4 On the terminal base adjacent to the adapter slide the FLEXBUS connector away from the adapter and remove the IO terminal base
5 Remove the adapter from the DIN rail
31039-M
1794-CE1 or 1794-CE3 cable
LOCAL rail
LOCAL2 rail
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
Publication 1794-IN002G-EN-P - January 2004
18 FlexLogix Controller System
Make an RS-232 Connection to the ControllerThe RS-232 port is a non-isolated serial port built-in to the front of the controller
To connect to the serial port
1 Determine whether you need an optical isolator
If you connect the controller to a device outside of the systemrsquos enclosure consider installing an isolator between the controller and device
One possible isolator is the 1761-NET-AIC interface converter
serial port
port 1 DB-9 RS-232 DTE
baud rate selector switch
port 2 mini-DIN 8 RS-232
dc power source selector switch
terminals for external 24V dc power supply
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 19
2 Select the appropriate cable
Are you using an isolator
Use this cable
no The 1756-CP3 cable attaches the controller directly to the controller
If you make your own cable it must be shielded and the shields must be tied to the metal shell (that surrounds the pins) on both ends of the cableYou can also use a 1747-CP3 cable (from the SLC product family) This cable has a taller right-angle connector housing than the 1756-CP3 cable
yes The 1761-CBL-AP00 cable (right-angle connector to controller) or the 1761-CBL-PM02 cable (straight connector to the controller) attaches the controller to port 2 on the 1761-NET-AIC isolator The mini-DIN connector is not commercially available so you cannot make this cable
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
DB-9 right-angle or straight cable end 8-pin mini-DIN cable end
Pin DB-9 end Mini-DIN end1 DCD DCD
2 RxD RxD
3 TxD TxD
4 DTR DTR
5 ground ground
6 DSR DSR
7 RTS RTS
8 CTS CTS
9 na na
1 2
34
5
6 7867
8
9
1
2
3
4
5
Publication 1794-IN002G-EN-P - January 2004
20 FlexLogix Controller System
3 Connect the appropriate cable to the serial port on the controller
Be sure that power is removed or the area is nonhazardous before proceeding
4 If necessary attach the controller to the isolator
WARNING If you connect or disconnect the serial cable with power applied to this module or the serial device on the other end of the cable an electrical arc can occur This could cause an explosion in hazardous location installations
modem
1761-NET-AIC isolator
user-supplied modem cable
1761 cable
system enclosure
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 21
Select the Operating Mode of the Controller
1 Use this table to determine the operating mode of the controller
2 Turn the key on the front panel of the controller to select the mode
If you want to Select one of these modes
Run Program Remote
Run Program Test
turn outputs to the state commanded by the logic of the project
YES YES
turn outputs to their configured state for Program mode
YES YES YES
execute (scan) tasks YES YES YES
change the mode of the controller through software
YES YES YES
download a project YES YES
schedule a ControlNet network YES YES
while online edit the project YES YES YES YES
To select Turn the key to
Remote Run RUN and then to REM
Remote Program PROG and then to REM
Remote Test REM and then go online and select Test mode via the programming software
keyswitch
Publication 1794-IN002G-EN-P - January 2004
22 FlexLogix Controller System
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware RevisionTo update the firmware of a controller first install a firmware upgrade kit
bull An upgrade kit ships on a supplemental CD along with RSLogix 5000 software
bull To download an upgrade kit go to httpsupportrockwellautomationcom Choose Firmware Updates
Indicator Color Description
RUN off bull no task(s) running
bull controller in Program mode
green bull one or more tasks are running
bull controller is in Run mode
OK off no power applied
red flashing after initially installing the controller - the controller requires a FLASH upgrade to the proper firmware revision see belowafter the controller is operating - recoverable fault
red bull controller faulted
bull clear faults clear memory or replace the controller
green controller OK
BATTERY off battery will support memory
red bull battery may not support memory
bull replace battery
IO off bull controller project not downloaded (the condition after power up)
bull no IO or communications configured
green communicating to all devices
green flashing one or more devices are not responding
LOCALandLOCAL2
off rail is inhibited
green communicating to all devices on that rail
green flashing one or more devices on that rail not responding
red flashing no modules exist on that rail
RS232 off no activity
green data being received or transmitted
FORCE off no forces present
amber forces present
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 23
Update the Controller
1 Connect the controller to the same network as your workstation
2 Start ControlFLASH software
3 Choose Next gt
4 Select the catalog number of the controller and choose Next gt
5 Expand the network until you see the controller If the required network is not shown first configure a driver for the network in RSLinx software
6 Select the controller and choose OK
7 Select the revision level to which you want to update the controller and choose Next gt
8 To start the update of the controller choose Finish and then Yes
After the controller is updated the status box displays Update complete
9 Choose OK
10 To close ControlFLASH software choose Cancel and then Yes
TIP RSLogix 5000 software revision 100 or later lets you update controller firmware as part of the download sequence To update the controller download your project and follow the prompts of the software
IMPORTANT If the Revision list is empty download a new upgrade kit Some older upgrade kits do not work with new controllers
weight 1794-L33 71 kg (156 lbs oz)1794-L34 75 g (166 lbs)(no communication cards installed)
28 kg (62 lbs)
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 27
power supply 1794-PS3 or 1794-PS13 ndash In applications that must be compliant with CSA requirements use a Separated Extra-Low Voltage (SELV) power supply that is compliant with IEC 610101 Annex H
power conductors 60deg C (140deg F) minimum copper22 to 14 AWG (0324 to 208 sq mm) stranded364 inch (12mm) insulation maximumlength 10m or less
category 3(2)
power connector torque 5 to 7 inch-pounds (06 to 08Nm)
battery 1756-BA1 (AB part number 94194801)059g lithium
na
serial cable 1761-CBLPM02 to 1761-NET-AIC 1761-CBLPA00 to 1761-NET-AIC1756-CP3 directly to controller1747-CP3 directly to controller
DIN rail steel 35 x 755mm DIN railA-B part number 199-DR1 46277-3 EN 50022
operating temperature IEC 60068-2-1 (Test Ad Operating Cold)IEC 60068-2-2 (Test Bd Operating Dry Heat)IEC 60068-2-14 (Test Nb Operating Thermal Shock)0 to 60degC (32 to 140degF)
storage temperature IEC 60068-2-1 (Test Ab Un-packaged Non-operating Cold)IEC 60068-2-2 (Test Bb Un-packaged Non-operating Dry Heat)IEC 60068-2-14 (Test Na Un-packaged Non-operating Thermal Shock)ndash40 to 85degC (ndash40 to 185degF)
relative humidity IEC 60068-2-30 (Test Db Un-packaged Non-operating Damp Heat)5 to 95 non-condensing
vibration(3) IEC60068-2-6 (Test Fc Operating) 5g 10-500Hz
shock(3)
operatingnon-operating
IEC60068-2-27 (Test Ea Unpackaged shock)
30g50g
emissions CISPR 11Group 1 Class A (with appropriate enclosure)
ESD immunity IEC 61000-4-26kV contact discharges8kV air discharges
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
RA-QR005C-EN-E 608
16 FlexLogix Controller System
4 Make sure power is not applied to the power supply Connect the power supply to the adapter This diagram and its related instructions describe a 1794-PS13 power supply
a Connect +24V dc input to the left adapter connector terminal A to the bottom left power connector terminal G
b Connect -24V common to left adapter connector terminal B to the top left power connector terminal E
c Use connections C and D on the adapter and connection F and H on the power supply to pass 24V dc power and common to the next module in the series if required
Use the screw-terminal connector plug that comes with the adapter to meet the requirements for installations in Class I Division 2 locations
5 Connect IO terminal bases and IO modules to the adapter the same way you connect them to the controller
6 Remove the plastic spacer from both ends of the extended-local IO cable (1794-CE1 or 1794-CE3)
plastic spacer
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 17
7 Connect the adapter to the controller
The following diagram shows how you can also use the 1794-CE1 -CE3 cable to split a rail of IO You can split each rail only once You can split a rail right after the controller (or adapter) or after any IO module For more information about the 1794-CE1 -CE3 cables see the Interconnect Cable Installation Instructions publication 1794-512
Removing the extended-local adapterIf you need to remove the adapter follow these steps
1 Turn off power to the adapter
2 Disconnect all cables from the adapter
3 Remove the IO module that is adjacent to the adapter
4 On the terminal base adjacent to the adapter slide the FLEXBUS connector away from the adapter and remove the IO terminal base
5 Remove the adapter from the DIN rail
31039-M
1794-CE1 or 1794-CE3 cable
LOCAL rail
LOCAL2 rail
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
Publication 1794-IN002G-EN-P - January 2004
18 FlexLogix Controller System
Make an RS-232 Connection to the ControllerThe RS-232 port is a non-isolated serial port built-in to the front of the controller
To connect to the serial port
1 Determine whether you need an optical isolator
If you connect the controller to a device outside of the systemrsquos enclosure consider installing an isolator between the controller and device
One possible isolator is the 1761-NET-AIC interface converter
serial port
port 1 DB-9 RS-232 DTE
baud rate selector switch
port 2 mini-DIN 8 RS-232
dc power source selector switch
terminals for external 24V dc power supply
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 19
2 Select the appropriate cable
Are you using an isolator
Use this cable
no The 1756-CP3 cable attaches the controller directly to the controller
If you make your own cable it must be shielded and the shields must be tied to the metal shell (that surrounds the pins) on both ends of the cableYou can also use a 1747-CP3 cable (from the SLC product family) This cable has a taller right-angle connector housing than the 1756-CP3 cable
yes The 1761-CBL-AP00 cable (right-angle connector to controller) or the 1761-CBL-PM02 cable (straight connector to the controller) attaches the controller to port 2 on the 1761-NET-AIC isolator The mini-DIN connector is not commercially available so you cannot make this cable
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
DB-9 right-angle or straight cable end 8-pin mini-DIN cable end
Pin DB-9 end Mini-DIN end1 DCD DCD
2 RxD RxD
3 TxD TxD
4 DTR DTR
5 ground ground
6 DSR DSR
7 RTS RTS
8 CTS CTS
9 na na
1 2
34
5
6 7867
8
9
1
2
3
4
5
Publication 1794-IN002G-EN-P - January 2004
20 FlexLogix Controller System
3 Connect the appropriate cable to the serial port on the controller
Be sure that power is removed or the area is nonhazardous before proceeding
4 If necessary attach the controller to the isolator
WARNING If you connect or disconnect the serial cable with power applied to this module or the serial device on the other end of the cable an electrical arc can occur This could cause an explosion in hazardous location installations
modem
1761-NET-AIC isolator
user-supplied modem cable
1761 cable
system enclosure
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 21
Select the Operating Mode of the Controller
1 Use this table to determine the operating mode of the controller
2 Turn the key on the front panel of the controller to select the mode
If you want to Select one of these modes
Run Program Remote
Run Program Test
turn outputs to the state commanded by the logic of the project
YES YES
turn outputs to their configured state for Program mode
YES YES YES
execute (scan) tasks YES YES YES
change the mode of the controller through software
YES YES YES
download a project YES YES
schedule a ControlNet network YES YES
while online edit the project YES YES YES YES
To select Turn the key to
Remote Run RUN and then to REM
Remote Program PROG and then to REM
Remote Test REM and then go online and select Test mode via the programming software
keyswitch
Publication 1794-IN002G-EN-P - January 2004
22 FlexLogix Controller System
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware RevisionTo update the firmware of a controller first install a firmware upgrade kit
bull An upgrade kit ships on a supplemental CD along with RSLogix 5000 software
bull To download an upgrade kit go to httpsupportrockwellautomationcom Choose Firmware Updates
Indicator Color Description
RUN off bull no task(s) running
bull controller in Program mode
green bull one or more tasks are running
bull controller is in Run mode
OK off no power applied
red flashing after initially installing the controller - the controller requires a FLASH upgrade to the proper firmware revision see belowafter the controller is operating - recoverable fault
red bull controller faulted
bull clear faults clear memory or replace the controller
green controller OK
BATTERY off battery will support memory
red bull battery may not support memory
bull replace battery
IO off bull controller project not downloaded (the condition after power up)
bull no IO or communications configured
green communicating to all devices
green flashing one or more devices are not responding
LOCALandLOCAL2
off rail is inhibited
green communicating to all devices on that rail
green flashing one or more devices on that rail not responding
red flashing no modules exist on that rail
RS232 off no activity
green data being received or transmitted
FORCE off no forces present
amber forces present
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 23
Update the Controller
1 Connect the controller to the same network as your workstation
2 Start ControlFLASH software
3 Choose Next gt
4 Select the catalog number of the controller and choose Next gt
5 Expand the network until you see the controller If the required network is not shown first configure a driver for the network in RSLinx software
6 Select the controller and choose OK
7 Select the revision level to which you want to update the controller and choose Next gt
8 To start the update of the controller choose Finish and then Yes
After the controller is updated the status box displays Update complete
9 Choose OK
10 To close ControlFLASH software choose Cancel and then Yes
TIP RSLogix 5000 software revision 100 or later lets you update controller firmware as part of the download sequence To update the controller download your project and follow the prompts of the software
IMPORTANT If the Revision list is empty download a new upgrade kit Some older upgrade kits do not work with new controllers
weight 1794-L33 71 kg (156 lbs oz)1794-L34 75 g (166 lbs)(no communication cards installed)
28 kg (62 lbs)
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 27
power supply 1794-PS3 or 1794-PS13 ndash In applications that must be compliant with CSA requirements use a Separated Extra-Low Voltage (SELV) power supply that is compliant with IEC 610101 Annex H
power conductors 60deg C (140deg F) minimum copper22 to 14 AWG (0324 to 208 sq mm) stranded364 inch (12mm) insulation maximumlength 10m or less
category 3(2)
power connector torque 5 to 7 inch-pounds (06 to 08Nm)
battery 1756-BA1 (AB part number 94194801)059g lithium
na
serial cable 1761-CBLPM02 to 1761-NET-AIC 1761-CBLPA00 to 1761-NET-AIC1756-CP3 directly to controller1747-CP3 directly to controller
DIN rail steel 35 x 755mm DIN railA-B part number 199-DR1 46277-3 EN 50022
operating temperature IEC 60068-2-1 (Test Ad Operating Cold)IEC 60068-2-2 (Test Bd Operating Dry Heat)IEC 60068-2-14 (Test Nb Operating Thermal Shock)0 to 60degC (32 to 140degF)
storage temperature IEC 60068-2-1 (Test Ab Un-packaged Non-operating Cold)IEC 60068-2-2 (Test Bb Un-packaged Non-operating Dry Heat)IEC 60068-2-14 (Test Na Un-packaged Non-operating Thermal Shock)ndash40 to 85degC (ndash40 to 185degF)
relative humidity IEC 60068-2-30 (Test Db Un-packaged Non-operating Damp Heat)5 to 95 non-condensing
vibration(3) IEC60068-2-6 (Test Fc Operating) 5g 10-500Hz
shock(3)
operatingnon-operating
IEC60068-2-27 (Test Ea Unpackaged shock)
30g50g
emissions CISPR 11Group 1 Class A (with appropriate enclosure)
ESD immunity IEC 61000-4-26kV contact discharges8kV air discharges
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
RA-QR005C-EN-E 608
FlexLogix Controller System 17
7 Connect the adapter to the controller
The following diagram shows how you can also use the 1794-CE1 -CE3 cable to split a rail of IO You can split each rail only once You can split a rail right after the controller (or adapter) or after any IO module For more information about the 1794-CE1 -CE3 cables see the Interconnect Cable Installation Instructions publication 1794-512
Removing the extended-local adapterIf you need to remove the adapter follow these steps
1 Turn off power to the adapter
2 Disconnect all cables from the adapter
3 Remove the IO module that is adjacent to the adapter
4 On the terminal base adjacent to the adapter slide the FLEXBUS connector away from the adapter and remove the IO terminal base
5 Remove the adapter from the DIN rail
31039-M
1794-CE1 or 1794-CE3 cable
LOCAL rail
LOCAL2 rail
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
1794-CE1 or 1794-CE3 cable
Publication 1794-IN002G-EN-P - January 2004
18 FlexLogix Controller System
Make an RS-232 Connection to the ControllerThe RS-232 port is a non-isolated serial port built-in to the front of the controller
To connect to the serial port
1 Determine whether you need an optical isolator
If you connect the controller to a device outside of the systemrsquos enclosure consider installing an isolator between the controller and device
One possible isolator is the 1761-NET-AIC interface converter
serial port
port 1 DB-9 RS-232 DTE
baud rate selector switch
port 2 mini-DIN 8 RS-232
dc power source selector switch
terminals for external 24V dc power supply
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 19
2 Select the appropriate cable
Are you using an isolator
Use this cable
no The 1756-CP3 cable attaches the controller directly to the controller
If you make your own cable it must be shielded and the shields must be tied to the metal shell (that surrounds the pins) on both ends of the cableYou can also use a 1747-CP3 cable (from the SLC product family) This cable has a taller right-angle connector housing than the 1756-CP3 cable
yes The 1761-CBL-AP00 cable (right-angle connector to controller) or the 1761-CBL-PM02 cable (straight connector to the controller) attaches the controller to port 2 on the 1761-NET-AIC isolator The mini-DIN connector is not commercially available so you cannot make this cable
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
DB-9 right-angle or straight cable end 8-pin mini-DIN cable end
Pin DB-9 end Mini-DIN end1 DCD DCD
2 RxD RxD
3 TxD TxD
4 DTR DTR
5 ground ground
6 DSR DSR
7 RTS RTS
8 CTS CTS
9 na na
1 2
34
5
6 7867
8
9
1
2
3
4
5
Publication 1794-IN002G-EN-P - January 2004
20 FlexLogix Controller System
3 Connect the appropriate cable to the serial port on the controller
Be sure that power is removed or the area is nonhazardous before proceeding
4 If necessary attach the controller to the isolator
WARNING If you connect or disconnect the serial cable with power applied to this module or the serial device on the other end of the cable an electrical arc can occur This could cause an explosion in hazardous location installations
modem
1761-NET-AIC isolator
user-supplied modem cable
1761 cable
system enclosure
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 21
Select the Operating Mode of the Controller
1 Use this table to determine the operating mode of the controller
2 Turn the key on the front panel of the controller to select the mode
If you want to Select one of these modes
Run Program Remote
Run Program Test
turn outputs to the state commanded by the logic of the project
YES YES
turn outputs to their configured state for Program mode
YES YES YES
execute (scan) tasks YES YES YES
change the mode of the controller through software
YES YES YES
download a project YES YES
schedule a ControlNet network YES YES
while online edit the project YES YES YES YES
To select Turn the key to
Remote Run RUN and then to REM
Remote Program PROG and then to REM
Remote Test REM and then go online and select Test mode via the programming software
keyswitch
Publication 1794-IN002G-EN-P - January 2004
22 FlexLogix Controller System
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware RevisionTo update the firmware of a controller first install a firmware upgrade kit
bull An upgrade kit ships on a supplemental CD along with RSLogix 5000 software
bull To download an upgrade kit go to httpsupportrockwellautomationcom Choose Firmware Updates
Indicator Color Description
RUN off bull no task(s) running
bull controller in Program mode
green bull one or more tasks are running
bull controller is in Run mode
OK off no power applied
red flashing after initially installing the controller - the controller requires a FLASH upgrade to the proper firmware revision see belowafter the controller is operating - recoverable fault
red bull controller faulted
bull clear faults clear memory or replace the controller
green controller OK
BATTERY off battery will support memory
red bull battery may not support memory
bull replace battery
IO off bull controller project not downloaded (the condition after power up)
bull no IO or communications configured
green communicating to all devices
green flashing one or more devices are not responding
LOCALandLOCAL2
off rail is inhibited
green communicating to all devices on that rail
green flashing one or more devices on that rail not responding
red flashing no modules exist on that rail
RS232 off no activity
green data being received or transmitted
FORCE off no forces present
amber forces present
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 23
Update the Controller
1 Connect the controller to the same network as your workstation
2 Start ControlFLASH software
3 Choose Next gt
4 Select the catalog number of the controller and choose Next gt
5 Expand the network until you see the controller If the required network is not shown first configure a driver for the network in RSLinx software
6 Select the controller and choose OK
7 Select the revision level to which you want to update the controller and choose Next gt
8 To start the update of the controller choose Finish and then Yes
After the controller is updated the status box displays Update complete
9 Choose OK
10 To close ControlFLASH software choose Cancel and then Yes
TIP RSLogix 5000 software revision 100 or later lets you update controller firmware as part of the download sequence To update the controller download your project and follow the prompts of the software
IMPORTANT If the Revision list is empty download a new upgrade kit Some older upgrade kits do not work with new controllers
weight 1794-L33 71 kg (156 lbs oz)1794-L34 75 g (166 lbs)(no communication cards installed)
28 kg (62 lbs)
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 27
power supply 1794-PS3 or 1794-PS13 ndash In applications that must be compliant with CSA requirements use a Separated Extra-Low Voltage (SELV) power supply that is compliant with IEC 610101 Annex H
power conductors 60deg C (140deg F) minimum copper22 to 14 AWG (0324 to 208 sq mm) stranded364 inch (12mm) insulation maximumlength 10m or less
category 3(2)
power connector torque 5 to 7 inch-pounds (06 to 08Nm)
battery 1756-BA1 (AB part number 94194801)059g lithium
na
serial cable 1761-CBLPM02 to 1761-NET-AIC 1761-CBLPA00 to 1761-NET-AIC1756-CP3 directly to controller1747-CP3 directly to controller
DIN rail steel 35 x 755mm DIN railA-B part number 199-DR1 46277-3 EN 50022
operating temperature IEC 60068-2-1 (Test Ad Operating Cold)IEC 60068-2-2 (Test Bd Operating Dry Heat)IEC 60068-2-14 (Test Nb Operating Thermal Shock)0 to 60degC (32 to 140degF)
storage temperature IEC 60068-2-1 (Test Ab Un-packaged Non-operating Cold)IEC 60068-2-2 (Test Bb Un-packaged Non-operating Dry Heat)IEC 60068-2-14 (Test Na Un-packaged Non-operating Thermal Shock)ndash40 to 85degC (ndash40 to 185degF)
relative humidity IEC 60068-2-30 (Test Db Un-packaged Non-operating Damp Heat)5 to 95 non-condensing
vibration(3) IEC60068-2-6 (Test Fc Operating) 5g 10-500Hz
shock(3)
operatingnon-operating
IEC60068-2-27 (Test Ea Unpackaged shock)
30g50g
emissions CISPR 11Group 1 Class A (with appropriate enclosure)
ESD immunity IEC 61000-4-26kV contact discharges8kV air discharges
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
RA-QR005C-EN-E 608
18 FlexLogix Controller System
Make an RS-232 Connection to the ControllerThe RS-232 port is a non-isolated serial port built-in to the front of the controller
To connect to the serial port
1 Determine whether you need an optical isolator
If you connect the controller to a device outside of the systemrsquos enclosure consider installing an isolator between the controller and device
One possible isolator is the 1761-NET-AIC interface converter
serial port
port 1 DB-9 RS-232 DTE
baud rate selector switch
port 2 mini-DIN 8 RS-232
dc power source selector switch
terminals for external 24V dc power supply
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 19
2 Select the appropriate cable
Are you using an isolator
Use this cable
no The 1756-CP3 cable attaches the controller directly to the controller
If you make your own cable it must be shielded and the shields must be tied to the metal shell (that surrounds the pins) on both ends of the cableYou can also use a 1747-CP3 cable (from the SLC product family) This cable has a taller right-angle connector housing than the 1756-CP3 cable
yes The 1761-CBL-AP00 cable (right-angle connector to controller) or the 1761-CBL-PM02 cable (straight connector to the controller) attaches the controller to port 2 on the 1761-NET-AIC isolator The mini-DIN connector is not commercially available so you cannot make this cable
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
DB-9 right-angle or straight cable end 8-pin mini-DIN cable end
Pin DB-9 end Mini-DIN end1 DCD DCD
2 RxD RxD
3 TxD TxD
4 DTR DTR
5 ground ground
6 DSR DSR
7 RTS RTS
8 CTS CTS
9 na na
1 2
34
5
6 7867
8
9
1
2
3
4
5
Publication 1794-IN002G-EN-P - January 2004
20 FlexLogix Controller System
3 Connect the appropriate cable to the serial port on the controller
Be sure that power is removed or the area is nonhazardous before proceeding
4 If necessary attach the controller to the isolator
WARNING If you connect or disconnect the serial cable with power applied to this module or the serial device on the other end of the cable an electrical arc can occur This could cause an explosion in hazardous location installations
modem
1761-NET-AIC isolator
user-supplied modem cable
1761 cable
system enclosure
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 21
Select the Operating Mode of the Controller
1 Use this table to determine the operating mode of the controller
2 Turn the key on the front panel of the controller to select the mode
If you want to Select one of these modes
Run Program Remote
Run Program Test
turn outputs to the state commanded by the logic of the project
YES YES
turn outputs to their configured state for Program mode
YES YES YES
execute (scan) tasks YES YES YES
change the mode of the controller through software
YES YES YES
download a project YES YES
schedule a ControlNet network YES YES
while online edit the project YES YES YES YES
To select Turn the key to
Remote Run RUN and then to REM
Remote Program PROG and then to REM
Remote Test REM and then go online and select Test mode via the programming software
keyswitch
Publication 1794-IN002G-EN-P - January 2004
22 FlexLogix Controller System
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware RevisionTo update the firmware of a controller first install a firmware upgrade kit
bull An upgrade kit ships on a supplemental CD along with RSLogix 5000 software
bull To download an upgrade kit go to httpsupportrockwellautomationcom Choose Firmware Updates
Indicator Color Description
RUN off bull no task(s) running
bull controller in Program mode
green bull one or more tasks are running
bull controller is in Run mode
OK off no power applied
red flashing after initially installing the controller - the controller requires a FLASH upgrade to the proper firmware revision see belowafter the controller is operating - recoverable fault
red bull controller faulted
bull clear faults clear memory or replace the controller
green controller OK
BATTERY off battery will support memory
red bull battery may not support memory
bull replace battery
IO off bull controller project not downloaded (the condition after power up)
bull no IO or communications configured
green communicating to all devices
green flashing one or more devices are not responding
LOCALandLOCAL2
off rail is inhibited
green communicating to all devices on that rail
green flashing one or more devices on that rail not responding
red flashing no modules exist on that rail
RS232 off no activity
green data being received or transmitted
FORCE off no forces present
amber forces present
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 23
Update the Controller
1 Connect the controller to the same network as your workstation
2 Start ControlFLASH software
3 Choose Next gt
4 Select the catalog number of the controller and choose Next gt
5 Expand the network until you see the controller If the required network is not shown first configure a driver for the network in RSLinx software
6 Select the controller and choose OK
7 Select the revision level to which you want to update the controller and choose Next gt
8 To start the update of the controller choose Finish and then Yes
After the controller is updated the status box displays Update complete
9 Choose OK
10 To close ControlFLASH software choose Cancel and then Yes
TIP RSLogix 5000 software revision 100 or later lets you update controller firmware as part of the download sequence To update the controller download your project and follow the prompts of the software
IMPORTANT If the Revision list is empty download a new upgrade kit Some older upgrade kits do not work with new controllers
weight 1794-L33 71 kg (156 lbs oz)1794-L34 75 g (166 lbs)(no communication cards installed)
28 kg (62 lbs)
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 27
power supply 1794-PS3 or 1794-PS13 ndash In applications that must be compliant with CSA requirements use a Separated Extra-Low Voltage (SELV) power supply that is compliant with IEC 610101 Annex H
power conductors 60deg C (140deg F) minimum copper22 to 14 AWG (0324 to 208 sq mm) stranded364 inch (12mm) insulation maximumlength 10m or less
category 3(2)
power connector torque 5 to 7 inch-pounds (06 to 08Nm)
battery 1756-BA1 (AB part number 94194801)059g lithium
na
serial cable 1761-CBLPM02 to 1761-NET-AIC 1761-CBLPA00 to 1761-NET-AIC1756-CP3 directly to controller1747-CP3 directly to controller
DIN rail steel 35 x 755mm DIN railA-B part number 199-DR1 46277-3 EN 50022
operating temperature IEC 60068-2-1 (Test Ad Operating Cold)IEC 60068-2-2 (Test Bd Operating Dry Heat)IEC 60068-2-14 (Test Nb Operating Thermal Shock)0 to 60degC (32 to 140degF)
storage temperature IEC 60068-2-1 (Test Ab Un-packaged Non-operating Cold)IEC 60068-2-2 (Test Bb Un-packaged Non-operating Dry Heat)IEC 60068-2-14 (Test Na Un-packaged Non-operating Thermal Shock)ndash40 to 85degC (ndash40 to 185degF)
relative humidity IEC 60068-2-30 (Test Db Un-packaged Non-operating Damp Heat)5 to 95 non-condensing
vibration(3) IEC60068-2-6 (Test Fc Operating) 5g 10-500Hz
shock(3)
operatingnon-operating
IEC60068-2-27 (Test Ea Unpackaged shock)
30g50g
emissions CISPR 11Group 1 Class A (with appropriate enclosure)
ESD immunity IEC 61000-4-26kV contact discharges8kV air discharges
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
RA-QR005C-EN-E 608
FlexLogix Controller System 19
2 Select the appropriate cable
Are you using an isolator
Use this cable
no The 1756-CP3 cable attaches the controller directly to the controller
If you make your own cable it must be shielded and the shields must be tied to the metal shell (that surrounds the pins) on both ends of the cableYou can also use a 1747-CP3 cable (from the SLC product family) This cable has a taller right-angle connector housing than the 1756-CP3 cable
yes The 1761-CBL-AP00 cable (right-angle connector to controller) or the 1761-CBL-PM02 cable (straight connector to the controller) attaches the controller to port 2 on the 1761-NET-AIC isolator The mini-DIN connector is not commercially available so you cannot make this cable
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
2 RDX
3 TXD
4 DTR
COMMON
6 DSR
7 RTS
8 CTS
9
1 CD
DB-9 right-angle or straight cable end 8-pin mini-DIN cable end
Pin DB-9 end Mini-DIN end1 DCD DCD
2 RxD RxD
3 TxD TxD
4 DTR DTR
5 ground ground
6 DSR DSR
7 RTS RTS
8 CTS CTS
9 na na
1 2
34
5
6 7867
8
9
1
2
3
4
5
Publication 1794-IN002G-EN-P - January 2004
20 FlexLogix Controller System
3 Connect the appropriate cable to the serial port on the controller
Be sure that power is removed or the area is nonhazardous before proceeding
4 If necessary attach the controller to the isolator
WARNING If you connect or disconnect the serial cable with power applied to this module or the serial device on the other end of the cable an electrical arc can occur This could cause an explosion in hazardous location installations
modem
1761-NET-AIC isolator
user-supplied modem cable
1761 cable
system enclosure
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 21
Select the Operating Mode of the Controller
1 Use this table to determine the operating mode of the controller
2 Turn the key on the front panel of the controller to select the mode
If you want to Select one of these modes
Run Program Remote
Run Program Test
turn outputs to the state commanded by the logic of the project
YES YES
turn outputs to their configured state for Program mode
YES YES YES
execute (scan) tasks YES YES YES
change the mode of the controller through software
YES YES YES
download a project YES YES
schedule a ControlNet network YES YES
while online edit the project YES YES YES YES
To select Turn the key to
Remote Run RUN and then to REM
Remote Program PROG and then to REM
Remote Test REM and then go online and select Test mode via the programming software
keyswitch
Publication 1794-IN002G-EN-P - January 2004
22 FlexLogix Controller System
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware RevisionTo update the firmware of a controller first install a firmware upgrade kit
bull An upgrade kit ships on a supplemental CD along with RSLogix 5000 software
bull To download an upgrade kit go to httpsupportrockwellautomationcom Choose Firmware Updates
Indicator Color Description
RUN off bull no task(s) running
bull controller in Program mode
green bull one or more tasks are running
bull controller is in Run mode
OK off no power applied
red flashing after initially installing the controller - the controller requires a FLASH upgrade to the proper firmware revision see belowafter the controller is operating - recoverable fault
red bull controller faulted
bull clear faults clear memory or replace the controller
green controller OK
BATTERY off battery will support memory
red bull battery may not support memory
bull replace battery
IO off bull controller project not downloaded (the condition after power up)
bull no IO or communications configured
green communicating to all devices
green flashing one or more devices are not responding
LOCALandLOCAL2
off rail is inhibited
green communicating to all devices on that rail
green flashing one or more devices on that rail not responding
red flashing no modules exist on that rail
RS232 off no activity
green data being received or transmitted
FORCE off no forces present
amber forces present
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 23
Update the Controller
1 Connect the controller to the same network as your workstation
2 Start ControlFLASH software
3 Choose Next gt
4 Select the catalog number of the controller and choose Next gt
5 Expand the network until you see the controller If the required network is not shown first configure a driver for the network in RSLinx software
6 Select the controller and choose OK
7 Select the revision level to which you want to update the controller and choose Next gt
8 To start the update of the controller choose Finish and then Yes
After the controller is updated the status box displays Update complete
9 Choose OK
10 To close ControlFLASH software choose Cancel and then Yes
TIP RSLogix 5000 software revision 100 or later lets you update controller firmware as part of the download sequence To update the controller download your project and follow the prompts of the software
IMPORTANT If the Revision list is empty download a new upgrade kit Some older upgrade kits do not work with new controllers
weight 1794-L33 71 kg (156 lbs oz)1794-L34 75 g (166 lbs)(no communication cards installed)
28 kg (62 lbs)
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 27
power supply 1794-PS3 or 1794-PS13 ndash In applications that must be compliant with CSA requirements use a Separated Extra-Low Voltage (SELV) power supply that is compliant with IEC 610101 Annex H
power conductors 60deg C (140deg F) minimum copper22 to 14 AWG (0324 to 208 sq mm) stranded364 inch (12mm) insulation maximumlength 10m or less
category 3(2)
power connector torque 5 to 7 inch-pounds (06 to 08Nm)
battery 1756-BA1 (AB part number 94194801)059g lithium
na
serial cable 1761-CBLPM02 to 1761-NET-AIC 1761-CBLPA00 to 1761-NET-AIC1756-CP3 directly to controller1747-CP3 directly to controller
DIN rail steel 35 x 755mm DIN railA-B part number 199-DR1 46277-3 EN 50022
operating temperature IEC 60068-2-1 (Test Ad Operating Cold)IEC 60068-2-2 (Test Bd Operating Dry Heat)IEC 60068-2-14 (Test Nb Operating Thermal Shock)0 to 60degC (32 to 140degF)
storage temperature IEC 60068-2-1 (Test Ab Un-packaged Non-operating Cold)IEC 60068-2-2 (Test Bb Un-packaged Non-operating Dry Heat)IEC 60068-2-14 (Test Na Un-packaged Non-operating Thermal Shock)ndash40 to 85degC (ndash40 to 185degF)
relative humidity IEC 60068-2-30 (Test Db Un-packaged Non-operating Damp Heat)5 to 95 non-condensing
vibration(3) IEC60068-2-6 (Test Fc Operating) 5g 10-500Hz
shock(3)
operatingnon-operating
IEC60068-2-27 (Test Ea Unpackaged shock)
30g50g
emissions CISPR 11Group 1 Class A (with appropriate enclosure)
ESD immunity IEC 61000-4-26kV contact discharges8kV air discharges
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
RA-QR005C-EN-E 608
20 FlexLogix Controller System
3 Connect the appropriate cable to the serial port on the controller
Be sure that power is removed or the area is nonhazardous before proceeding
4 If necessary attach the controller to the isolator
WARNING If you connect or disconnect the serial cable with power applied to this module or the serial device on the other end of the cable an electrical arc can occur This could cause an explosion in hazardous location installations
modem
1761-NET-AIC isolator
user-supplied modem cable
1761 cable
system enclosure
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 21
Select the Operating Mode of the Controller
1 Use this table to determine the operating mode of the controller
2 Turn the key on the front panel of the controller to select the mode
If you want to Select one of these modes
Run Program Remote
Run Program Test
turn outputs to the state commanded by the logic of the project
YES YES
turn outputs to their configured state for Program mode
YES YES YES
execute (scan) tasks YES YES YES
change the mode of the controller through software
YES YES YES
download a project YES YES
schedule a ControlNet network YES YES
while online edit the project YES YES YES YES
To select Turn the key to
Remote Run RUN and then to REM
Remote Program PROG and then to REM
Remote Test REM and then go online and select Test mode via the programming software
keyswitch
Publication 1794-IN002G-EN-P - January 2004
22 FlexLogix Controller System
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware RevisionTo update the firmware of a controller first install a firmware upgrade kit
bull An upgrade kit ships on a supplemental CD along with RSLogix 5000 software
bull To download an upgrade kit go to httpsupportrockwellautomationcom Choose Firmware Updates
Indicator Color Description
RUN off bull no task(s) running
bull controller in Program mode
green bull one or more tasks are running
bull controller is in Run mode
OK off no power applied
red flashing after initially installing the controller - the controller requires a FLASH upgrade to the proper firmware revision see belowafter the controller is operating - recoverable fault
red bull controller faulted
bull clear faults clear memory or replace the controller
green controller OK
BATTERY off battery will support memory
red bull battery may not support memory
bull replace battery
IO off bull controller project not downloaded (the condition after power up)
bull no IO or communications configured
green communicating to all devices
green flashing one or more devices are not responding
LOCALandLOCAL2
off rail is inhibited
green communicating to all devices on that rail
green flashing one or more devices on that rail not responding
red flashing no modules exist on that rail
RS232 off no activity
green data being received or transmitted
FORCE off no forces present
amber forces present
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 23
Update the Controller
1 Connect the controller to the same network as your workstation
2 Start ControlFLASH software
3 Choose Next gt
4 Select the catalog number of the controller and choose Next gt
5 Expand the network until you see the controller If the required network is not shown first configure a driver for the network in RSLinx software
6 Select the controller and choose OK
7 Select the revision level to which you want to update the controller and choose Next gt
8 To start the update of the controller choose Finish and then Yes
After the controller is updated the status box displays Update complete
9 Choose OK
10 To close ControlFLASH software choose Cancel and then Yes
TIP RSLogix 5000 software revision 100 or later lets you update controller firmware as part of the download sequence To update the controller download your project and follow the prompts of the software
IMPORTANT If the Revision list is empty download a new upgrade kit Some older upgrade kits do not work with new controllers
weight 1794-L33 71 kg (156 lbs oz)1794-L34 75 g (166 lbs)(no communication cards installed)
28 kg (62 lbs)
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 27
power supply 1794-PS3 or 1794-PS13 ndash In applications that must be compliant with CSA requirements use a Separated Extra-Low Voltage (SELV) power supply that is compliant with IEC 610101 Annex H
power conductors 60deg C (140deg F) minimum copper22 to 14 AWG (0324 to 208 sq mm) stranded364 inch (12mm) insulation maximumlength 10m or less
category 3(2)
power connector torque 5 to 7 inch-pounds (06 to 08Nm)
battery 1756-BA1 (AB part number 94194801)059g lithium
na
serial cable 1761-CBLPM02 to 1761-NET-AIC 1761-CBLPA00 to 1761-NET-AIC1756-CP3 directly to controller1747-CP3 directly to controller
DIN rail steel 35 x 755mm DIN railA-B part number 199-DR1 46277-3 EN 50022
operating temperature IEC 60068-2-1 (Test Ad Operating Cold)IEC 60068-2-2 (Test Bd Operating Dry Heat)IEC 60068-2-14 (Test Nb Operating Thermal Shock)0 to 60degC (32 to 140degF)
storage temperature IEC 60068-2-1 (Test Ab Un-packaged Non-operating Cold)IEC 60068-2-2 (Test Bb Un-packaged Non-operating Dry Heat)IEC 60068-2-14 (Test Na Un-packaged Non-operating Thermal Shock)ndash40 to 85degC (ndash40 to 185degF)
relative humidity IEC 60068-2-30 (Test Db Un-packaged Non-operating Damp Heat)5 to 95 non-condensing
vibration(3) IEC60068-2-6 (Test Fc Operating) 5g 10-500Hz
shock(3)
operatingnon-operating
IEC60068-2-27 (Test Ea Unpackaged shock)
30g50g
emissions CISPR 11Group 1 Class A (with appropriate enclosure)
ESD immunity IEC 61000-4-26kV contact discharges8kV air discharges
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
RA-QR005C-EN-E 608
FlexLogix Controller System 21
Select the Operating Mode of the Controller
1 Use this table to determine the operating mode of the controller
2 Turn the key on the front panel of the controller to select the mode
If you want to Select one of these modes
Run Program Remote
Run Program Test
turn outputs to the state commanded by the logic of the project
YES YES
turn outputs to their configured state for Program mode
YES YES YES
execute (scan) tasks YES YES YES
change the mode of the controller through software
YES YES YES
download a project YES YES
schedule a ControlNet network YES YES
while online edit the project YES YES YES YES
To select Turn the key to
Remote Run RUN and then to REM
Remote Program PROG and then to REM
Remote Test REM and then go online and select Test mode via the programming software
keyswitch
Publication 1794-IN002G-EN-P - January 2004
22 FlexLogix Controller System
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware RevisionTo update the firmware of a controller first install a firmware upgrade kit
bull An upgrade kit ships on a supplemental CD along with RSLogix 5000 software
bull To download an upgrade kit go to httpsupportrockwellautomationcom Choose Firmware Updates
Indicator Color Description
RUN off bull no task(s) running
bull controller in Program mode
green bull one or more tasks are running
bull controller is in Run mode
OK off no power applied
red flashing after initially installing the controller - the controller requires a FLASH upgrade to the proper firmware revision see belowafter the controller is operating - recoverable fault
red bull controller faulted
bull clear faults clear memory or replace the controller
green controller OK
BATTERY off battery will support memory
red bull battery may not support memory
bull replace battery
IO off bull controller project not downloaded (the condition after power up)
bull no IO or communications configured
green communicating to all devices
green flashing one or more devices are not responding
LOCALandLOCAL2
off rail is inhibited
green communicating to all devices on that rail
green flashing one or more devices on that rail not responding
red flashing no modules exist on that rail
RS232 off no activity
green data being received or transmitted
FORCE off no forces present
amber forces present
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 23
Update the Controller
1 Connect the controller to the same network as your workstation
2 Start ControlFLASH software
3 Choose Next gt
4 Select the catalog number of the controller and choose Next gt
5 Expand the network until you see the controller If the required network is not shown first configure a driver for the network in RSLinx software
6 Select the controller and choose OK
7 Select the revision level to which you want to update the controller and choose Next gt
8 To start the update of the controller choose Finish and then Yes
After the controller is updated the status box displays Update complete
9 Choose OK
10 To close ControlFLASH software choose Cancel and then Yes
TIP RSLogix 5000 software revision 100 or later lets you update controller firmware as part of the download sequence To update the controller download your project and follow the prompts of the software
IMPORTANT If the Revision list is empty download a new upgrade kit Some older upgrade kits do not work with new controllers
weight 1794-L33 71 kg (156 lbs oz)1794-L34 75 g (166 lbs)(no communication cards installed)
28 kg (62 lbs)
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 27
power supply 1794-PS3 or 1794-PS13 ndash In applications that must be compliant with CSA requirements use a Separated Extra-Low Voltage (SELV) power supply that is compliant with IEC 610101 Annex H
power conductors 60deg C (140deg F) minimum copper22 to 14 AWG (0324 to 208 sq mm) stranded364 inch (12mm) insulation maximumlength 10m or less
category 3(2)
power connector torque 5 to 7 inch-pounds (06 to 08Nm)
battery 1756-BA1 (AB part number 94194801)059g lithium
na
serial cable 1761-CBLPM02 to 1761-NET-AIC 1761-CBLPA00 to 1761-NET-AIC1756-CP3 directly to controller1747-CP3 directly to controller
DIN rail steel 35 x 755mm DIN railA-B part number 199-DR1 46277-3 EN 50022
operating temperature IEC 60068-2-1 (Test Ad Operating Cold)IEC 60068-2-2 (Test Bd Operating Dry Heat)IEC 60068-2-14 (Test Nb Operating Thermal Shock)0 to 60degC (32 to 140degF)
storage temperature IEC 60068-2-1 (Test Ab Un-packaged Non-operating Cold)IEC 60068-2-2 (Test Bb Un-packaged Non-operating Dry Heat)IEC 60068-2-14 (Test Na Un-packaged Non-operating Thermal Shock)ndash40 to 85degC (ndash40 to 185degF)
relative humidity IEC 60068-2-30 (Test Db Un-packaged Non-operating Damp Heat)5 to 95 non-condensing
vibration(3) IEC60068-2-6 (Test Fc Operating) 5g 10-500Hz
shock(3)
operatingnon-operating
IEC60068-2-27 (Test Ea Unpackaged shock)
30g50g
emissions CISPR 11Group 1 Class A (with appropriate enclosure)
ESD immunity IEC 61000-4-26kV contact discharges8kV air discharges
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
RA-QR005C-EN-E 608
22 FlexLogix Controller System
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware RevisionTo update the firmware of a controller first install a firmware upgrade kit
bull An upgrade kit ships on a supplemental CD along with RSLogix 5000 software
bull To download an upgrade kit go to httpsupportrockwellautomationcom Choose Firmware Updates
Indicator Color Description
RUN off bull no task(s) running
bull controller in Program mode
green bull one or more tasks are running
bull controller is in Run mode
OK off no power applied
red flashing after initially installing the controller - the controller requires a FLASH upgrade to the proper firmware revision see belowafter the controller is operating - recoverable fault
red bull controller faulted
bull clear faults clear memory or replace the controller
green controller OK
BATTERY off battery will support memory
red bull battery may not support memory
bull replace battery
IO off bull controller project not downloaded (the condition after power up)
bull no IO or communications configured
green communicating to all devices
green flashing one or more devices are not responding
LOCALandLOCAL2
off rail is inhibited
green communicating to all devices on that rail
green flashing one or more devices on that rail not responding
red flashing no modules exist on that rail
RS232 off no activity
green data being received or transmitted
FORCE off no forces present
amber forces present
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 23
Update the Controller
1 Connect the controller to the same network as your workstation
2 Start ControlFLASH software
3 Choose Next gt
4 Select the catalog number of the controller and choose Next gt
5 Expand the network until you see the controller If the required network is not shown first configure a driver for the network in RSLinx software
6 Select the controller and choose OK
7 Select the revision level to which you want to update the controller and choose Next gt
8 To start the update of the controller choose Finish and then Yes
After the controller is updated the status box displays Update complete
9 Choose OK
10 To close ControlFLASH software choose Cancel and then Yes
TIP RSLogix 5000 software revision 100 or later lets you update controller firmware as part of the download sequence To update the controller download your project and follow the prompts of the software
IMPORTANT If the Revision list is empty download a new upgrade kit Some older upgrade kits do not work with new controllers
weight 1794-L33 71 kg (156 lbs oz)1794-L34 75 g (166 lbs)(no communication cards installed)
28 kg (62 lbs)
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 27
power supply 1794-PS3 or 1794-PS13 ndash In applications that must be compliant with CSA requirements use a Separated Extra-Low Voltage (SELV) power supply that is compliant with IEC 610101 Annex H
power conductors 60deg C (140deg F) minimum copper22 to 14 AWG (0324 to 208 sq mm) stranded364 inch (12mm) insulation maximumlength 10m or less
category 3(2)
power connector torque 5 to 7 inch-pounds (06 to 08Nm)
battery 1756-BA1 (AB part number 94194801)059g lithium
na
serial cable 1761-CBLPM02 to 1761-NET-AIC 1761-CBLPA00 to 1761-NET-AIC1756-CP3 directly to controller1747-CP3 directly to controller
DIN rail steel 35 x 755mm DIN railA-B part number 199-DR1 46277-3 EN 50022
operating temperature IEC 60068-2-1 (Test Ad Operating Cold)IEC 60068-2-2 (Test Bd Operating Dry Heat)IEC 60068-2-14 (Test Nb Operating Thermal Shock)0 to 60degC (32 to 140degF)
storage temperature IEC 60068-2-1 (Test Ab Un-packaged Non-operating Cold)IEC 60068-2-2 (Test Bb Un-packaged Non-operating Dry Heat)IEC 60068-2-14 (Test Na Un-packaged Non-operating Thermal Shock)ndash40 to 85degC (ndash40 to 185degF)
relative humidity IEC 60068-2-30 (Test Db Un-packaged Non-operating Damp Heat)5 to 95 non-condensing
vibration(3) IEC60068-2-6 (Test Fc Operating) 5g 10-500Hz
shock(3)
operatingnon-operating
IEC60068-2-27 (Test Ea Unpackaged shock)
30g50g
emissions CISPR 11Group 1 Class A (with appropriate enclosure)
ESD immunity IEC 61000-4-26kV contact discharges8kV air discharges
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
RA-QR005C-EN-E 608
FlexLogix Controller System 23
Update the Controller
1 Connect the controller to the same network as your workstation
2 Start ControlFLASH software
3 Choose Next gt
4 Select the catalog number of the controller and choose Next gt
5 Expand the network until you see the controller If the required network is not shown first configure a driver for the network in RSLinx software
6 Select the controller and choose OK
7 Select the revision level to which you want to update the controller and choose Next gt
8 To start the update of the controller choose Finish and then Yes
After the controller is updated the status box displays Update complete
9 Choose OK
10 To close ControlFLASH software choose Cancel and then Yes
TIP RSLogix 5000 software revision 100 or later lets you update controller firmware as part of the download sequence To update the controller download your project and follow the prompts of the software
IMPORTANT If the Revision list is empty download a new upgrade kit Some older upgrade kits do not work with new controllers
weight 1794-L33 71 kg (156 lbs oz)1794-L34 75 g (166 lbs)(no communication cards installed)
28 kg (62 lbs)
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 27
power supply 1794-PS3 or 1794-PS13 ndash In applications that must be compliant with CSA requirements use a Separated Extra-Low Voltage (SELV) power supply that is compliant with IEC 610101 Annex H
power conductors 60deg C (140deg F) minimum copper22 to 14 AWG (0324 to 208 sq mm) stranded364 inch (12mm) insulation maximumlength 10m or less
category 3(2)
power connector torque 5 to 7 inch-pounds (06 to 08Nm)
battery 1756-BA1 (AB part number 94194801)059g lithium
na
serial cable 1761-CBLPM02 to 1761-NET-AIC 1761-CBLPA00 to 1761-NET-AIC1756-CP3 directly to controller1747-CP3 directly to controller
DIN rail steel 35 x 755mm DIN railA-B part number 199-DR1 46277-3 EN 50022
operating temperature IEC 60068-2-1 (Test Ad Operating Cold)IEC 60068-2-2 (Test Bd Operating Dry Heat)IEC 60068-2-14 (Test Nb Operating Thermal Shock)0 to 60degC (32 to 140degF)
storage temperature IEC 60068-2-1 (Test Ab Un-packaged Non-operating Cold)IEC 60068-2-2 (Test Bb Un-packaged Non-operating Dry Heat)IEC 60068-2-14 (Test Na Un-packaged Non-operating Thermal Shock)ndash40 to 85degC (ndash40 to 185degF)
relative humidity IEC 60068-2-30 (Test Db Un-packaged Non-operating Damp Heat)5 to 95 non-condensing
vibration(3) IEC60068-2-6 (Test Fc Operating) 5g 10-500Hz
shock(3)
operatingnon-operating
IEC60068-2-27 (Test Ea Unpackaged shock)
30g50g
emissions CISPR 11Group 1 Class A (with appropriate enclosure)
ESD immunity IEC 61000-4-26kV contact discharges8kV air discharges
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
weight 1794-L33 71 kg (156 lbs oz)1794-L34 75 g (166 lbs)(no communication cards installed)
28 kg (62 lbs)
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 27
power supply 1794-PS3 or 1794-PS13 ndash In applications that must be compliant with CSA requirements use a Separated Extra-Low Voltage (SELV) power supply that is compliant with IEC 610101 Annex H
power conductors 60deg C (140deg F) minimum copper22 to 14 AWG (0324 to 208 sq mm) stranded364 inch (12mm) insulation maximumlength 10m or less
category 3(2)
power connector torque 5 to 7 inch-pounds (06 to 08Nm)
battery 1756-BA1 (AB part number 94194801)059g lithium
na
serial cable 1761-CBLPM02 to 1761-NET-AIC 1761-CBLPA00 to 1761-NET-AIC1756-CP3 directly to controller1747-CP3 directly to controller
DIN rail steel 35 x 755mm DIN railA-B part number 199-DR1 46277-3 EN 50022
operating temperature IEC 60068-2-1 (Test Ad Operating Cold)IEC 60068-2-2 (Test Bd Operating Dry Heat)IEC 60068-2-14 (Test Nb Operating Thermal Shock)0 to 60degC (32 to 140degF)
storage temperature IEC 60068-2-1 (Test Ab Un-packaged Non-operating Cold)IEC 60068-2-2 (Test Bb Un-packaged Non-operating Dry Heat)IEC 60068-2-14 (Test Na Un-packaged Non-operating Thermal Shock)ndash40 to 85degC (ndash40 to 185degF)
relative humidity IEC 60068-2-30 (Test Db Un-packaged Non-operating Damp Heat)5 to 95 non-condensing
vibration(3) IEC60068-2-6 (Test Fc Operating) 5g 10-500Hz
shock(3)
operatingnon-operating
IEC60068-2-27 (Test Ea Unpackaged shock)
30g50g
emissions CISPR 11Group 1 Class A (with appropriate enclosure)
ESD immunity IEC 61000-4-26kV contact discharges8kV air discharges
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
weight 1794-L33 71 kg (156 lbs oz)1794-L34 75 g (166 lbs)(no communication cards installed)
28 kg (62 lbs)
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 27
power supply 1794-PS3 or 1794-PS13 ndash In applications that must be compliant with CSA requirements use a Separated Extra-Low Voltage (SELV) power supply that is compliant with IEC 610101 Annex H
power conductors 60deg C (140deg F) minimum copper22 to 14 AWG (0324 to 208 sq mm) stranded364 inch (12mm) insulation maximumlength 10m or less
category 3(2)
power connector torque 5 to 7 inch-pounds (06 to 08Nm)
battery 1756-BA1 (AB part number 94194801)059g lithium
na
serial cable 1761-CBLPM02 to 1761-NET-AIC 1761-CBLPA00 to 1761-NET-AIC1756-CP3 directly to controller1747-CP3 directly to controller
DIN rail steel 35 x 755mm DIN railA-B part number 199-DR1 46277-3 EN 50022
operating temperature IEC 60068-2-1 (Test Ad Operating Cold)IEC 60068-2-2 (Test Bd Operating Dry Heat)IEC 60068-2-14 (Test Nb Operating Thermal Shock)0 to 60degC (32 to 140degF)
storage temperature IEC 60068-2-1 (Test Ab Un-packaged Non-operating Cold)IEC 60068-2-2 (Test Bb Un-packaged Non-operating Dry Heat)IEC 60068-2-14 (Test Na Un-packaged Non-operating Thermal Shock)ndash40 to 85degC (ndash40 to 185degF)
relative humidity IEC 60068-2-30 (Test Db Un-packaged Non-operating Damp Heat)5 to 95 non-condensing
vibration(3) IEC60068-2-6 (Test Fc Operating) 5g 10-500Hz
shock(3)
operatingnon-operating
IEC60068-2-27 (Test Ea Unpackaged shock)
30g50g
emissions CISPR 11Group 1 Class A (with appropriate enclosure)
ESD immunity IEC 61000-4-26kV contact discharges8kV air discharges
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
RA-QR005C-EN-E 608
26 FlexLogix Controller System
Other PublicationsYou can use the following manuals with this product
You can obtain manuals at wwwtheautomationbookstorecom
Specifications
Documents required for installation details Publication number
Industrial Automation Wiring and Grounding Guidelines 1770-41
Flex 1794-PS3 Power Supply Installation Instructions 1794-571
Flex 1794-PS13 Power Supply Installation Instructions 1794-569
Flex IO Terminal Base Installation Instructions 1794-516
weight 1794-L33 71 kg (156 lbs oz)1794-L34 75 g (166 lbs)(no communication cards installed)
28 kg (62 lbs)
Publication 1794-IN002G-EN-P - January 2004
FlexLogix Controller System 27
power supply 1794-PS3 or 1794-PS13 ndash In applications that must be compliant with CSA requirements use a Separated Extra-Low Voltage (SELV) power supply that is compliant with IEC 610101 Annex H
power conductors 60deg C (140deg F) minimum copper22 to 14 AWG (0324 to 208 sq mm) stranded364 inch (12mm) insulation maximumlength 10m or less
category 3(2)
power connector torque 5 to 7 inch-pounds (06 to 08Nm)
battery 1756-BA1 (AB part number 94194801)059g lithium
na
serial cable 1761-CBLPM02 to 1761-NET-AIC 1761-CBLPA00 to 1761-NET-AIC1756-CP3 directly to controller1747-CP3 directly to controller
DIN rail steel 35 x 755mm DIN railA-B part number 199-DR1 46277-3 EN 50022
operating temperature IEC 60068-2-1 (Test Ad Operating Cold)IEC 60068-2-2 (Test Bd Operating Dry Heat)IEC 60068-2-14 (Test Nb Operating Thermal Shock)0 to 60degC (32 to 140degF)
storage temperature IEC 60068-2-1 (Test Ab Un-packaged Non-operating Cold)IEC 60068-2-2 (Test Bb Un-packaged Non-operating Dry Heat)IEC 60068-2-14 (Test Na Un-packaged Non-operating Thermal Shock)ndash40 to 85degC (ndash40 to 185degF)
relative humidity IEC 60068-2-30 (Test Db Un-packaged Non-operating Damp Heat)5 to 95 non-condensing
vibration(3) IEC60068-2-6 (Test Fc Operating) 5g 10-500Hz
shock(3)
operatingnon-operating
IEC60068-2-27 (Test Ea Unpackaged shock)
30g50g
emissions CISPR 11Group 1 Class A (with appropriate enclosure)
ESD immunity IEC 61000-4-26kV contact discharges8kV air discharges
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
RA-QR005C-EN-E 608
FlexLogix Controller System 27
power supply 1794-PS3 or 1794-PS13 ndash In applications that must be compliant with CSA requirements use a Separated Extra-Low Voltage (SELV) power supply that is compliant with IEC 610101 Annex H
power conductors 60deg C (140deg F) minimum copper22 to 14 AWG (0324 to 208 sq mm) stranded364 inch (12mm) insulation maximumlength 10m or less
category 3(2)
power connector torque 5 to 7 inch-pounds (06 to 08Nm)
battery 1756-BA1 (AB part number 94194801)059g lithium
na
serial cable 1761-CBLPM02 to 1761-NET-AIC 1761-CBLPA00 to 1761-NET-AIC1756-CP3 directly to controller1747-CP3 directly to controller
DIN rail steel 35 x 755mm DIN railA-B part number 199-DR1 46277-3 EN 50022
operating temperature IEC 60068-2-1 (Test Ad Operating Cold)IEC 60068-2-2 (Test Bd Operating Dry Heat)IEC 60068-2-14 (Test Nb Operating Thermal Shock)0 to 60degC (32 to 140degF)
storage temperature IEC 60068-2-1 (Test Ab Un-packaged Non-operating Cold)IEC 60068-2-2 (Test Bb Un-packaged Non-operating Dry Heat)IEC 60068-2-14 (Test Na Un-packaged Non-operating Thermal Shock)ndash40 to 85degC (ndash40 to 185degF)
relative humidity IEC 60068-2-30 (Test Db Un-packaged Non-operating Damp Heat)5 to 95 non-condensing
vibration(3) IEC60068-2-6 (Test Fc Operating) 5g 10-500Hz
shock(3)
operatingnon-operating
IEC60068-2-27 (Test Ea Unpackaged shock)
30g50g
emissions CISPR 11Group 1 Class A (with appropriate enclosure)
ESD immunity IEC 61000-4-26kV contact discharges8kV air discharges
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
RA-QR005C-EN-E 608
radiated RF immunity IEC 61000-4-310Vm with 1kHz sine-wave 80AM from 30MHz to 2000MHz10Vm with 200Hz 50 Pulse 100AM at 900Mhz
EFTB immunity IEC 61000-4-4plusmn4kV at 25kHz on power portsplusmn2kV at 5kHz on communications ports
surge transient immunity IEC 61000-4-5plusmn2kV line-earth (CM) on shielded ports
conducted RF immunity IEC 61000-4-610Vrms with 1kHz sine-wave 80AM from 150kHz to 80MHz
enclosure type rating none (open-style)
Certifications(when product is marked)
UL UL Listed Industrial Control Equipmentc-UL-us UL Listed for Class I Division 2 Group ABCD Hazardous
Locations certified for US and CanadaCSA CSA Certified Process Control EquipmentCSA CSA Certified Process Control Equipment for Class I Division 2
C-Tick(5) Australian Radiocommunications Act compliant withASNZS CISPR 11 Industrial Emissions
EEx(5) European Union 949EEC ATEX Directive compliant withEN 50021 Potentially Explosive Atmospheres Protection n (Zone 2)
(1) This specification is also known as Power Consumption(2) This specification is also known as Heat Dissipation(3) To maintain these vibration and shock specifications you must use DIN rail locks(4) Use this Conductor Category information for planning conductor routing Refer to Publication 1770-41 Industrial
Automation Wiring and Grounding Guidelines(5) See the Product Certification link at wwwabcom for Declarations of Conformity Certificates and other certification
details
Category FlexLogix controller(1794-L33 -L34)
FlexLogix extended-local IO adapter (1794-FLA)
Publication 1794-IN002G-EN-P - January 2004 PN 957867-01Supersedes Publication 1794-IN002F-EN-P - October 2002 Copyright copy 2004 Rockwell Automation Inc All rights reserved Printed in the USA
1794-IN002G-EN-P FlexLogix Controller System Installation Instructions
Tools That You Need
Obtain a User Manual
Environment and Enclosure
Prevent Electrostatic Discharge
European Hazardous Location Approval
North American Hazardous Location Approval
Removal and Insertion Under Power
Other Considerations
What You Need to Do
Step 1 Verify That You Have All the Components
Step 2 Install the Battery
Step 3 Install Communication Daughtercards (optional)
Step 4 Install the Controller
Step 5 Install the Extended-Local Adapter (optional)
Make an RS-232 Connection to the Controller
Select the Operating Mode of the Controller
Monitor the Controller LEDs
FLASH Upgrade the Controllerrsquos Firmware Revision
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
Details of the Rockwell Automation Print Specifications sheet
This print specifications sheet is designed with multiple purposes- It is a vehicle to get the most accurate print specifications to RA-approved print vendors- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must completeTo facilitate the most efficient use of this sheet we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specificationsIMPORTANT Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications there are some columns hidden For example the first field you must complete is Column E or Publication Number Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can completeDO NOT delete any hidden columns from the tab you choose to use
Definitions of Each Tab in Sheet
Generic pub print specs
Single sheet with all required columns for necessary specifications None of the columns are completed All must be completed before attaching the sheet to your PDFThis tab has 39 blank fields you must complete via free text type or pull-down menus
IN RN pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to installation instructions (IN) and release notes (RN) However you can use this sheet for other publications that are similar to INs and RNsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
UM RM PM pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to user manuals (UM) reference manuals (RM) and programming manuals (PM) However you can use this sheet for other publications that are similar to UMs RMs and PMsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
AP PP pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to application solutions (AP) and product profiles (PP) However you can use this sheet for other publications that are similar to APs and PPsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
BR pub type specs
Templates with many fields already completed according to typical default settings Use this tab with publications similar to brochures (BR) However you can use this sheet for other publications that are similar to BRsThis sheet has several fields already completed with default values which you can change You must complete the additional fields
Field definitions
Description of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user
Attach Print Specs to PDF
For Acrobat 80 follow these steps1 Open the PDF2 Click on DocumentgtAttach A File A new section appears at the bottom of the PDF3 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 70 follow these steps1 Open the PDF2 Click on the Attachments tab next to the publications bookmarks A new section appears at the bottom of the PDF3 Click on the Add button in the bottom section of the PDF4 Browse to the MS Excel file with the print specs and add it to the PDFFor Acrobat 60 follow these steps1 Open the PDF2 Go to the backcover of the PDF3 Click on the Tools pull-down menu4 Click on this sequence of menu options - Advanced Commenting Attach Attach File Tool A paper clip appears5 Click to put the paper clip somewhere on the backcover The browse window appears6 Browse to the MS Excel file with the print specs and add it to the PDFIMPORTANT If you are using Acrobat 50 or earlier please upgrade
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
Corp
17501
Bill To
69
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
See DocMan for the Cost Center selections associated with each Business Group
RRD must provide this information
RRD must provide this information
RRD must provide this information
RRD must provide this information
IN RN pub type specs
UM RM PM pub type specs
AP PP pub type specs
BR pub type specs
Field definitions
ampL04032006ampRampP
PackagingOrdering Unit Of Measure
EA = Each
PK = Pack
PD = Pad
RL = Roll
BK = Book
CT = Carton
BX = Box
ST = Set
Multiple Order Qty
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
1794-IN002G-EN-P
FlexLogix Controller Installation Instructions
EA
1
1
Marketing Commercial
19021
01232004
5
Black amp White
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
4
28
7
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
55
85
NA
NA
NA
NA
NA
HALF
55 x 85
100
RRD must provide this information
Text Stock = 20 White Opaque BondText Ink = Black
957867-01
UM RM PM pub type specs
AP PP pub type specs
BR pub type specs
Field definitions
ampL04032006ampRampP
PackagingOrdering Unit Of Measure
EA = Each
PK = Pack
PD = Pad
RL = Roll
BK = Book
CT = Carton
BX = Box
ST = Set
Multiple Order Qty
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
EA
1
1
See DocMan for the Cost Center selections associated with each Business Group
Black amp White
B
PERFECT
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
2
PLAIN
20
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
516
3LEFT
NA
NA
NA
NA
RRD must provide this information
Cover Stock = 90 White IndexText Stock = 20 White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF
AP PP pub type specs
BR pub type specs
Field definitions
ampL04032006ampRampP
PackagingOrdering Unit Of Measure
EA = Each
PK = Pack
PD = Pad
RL = Roll
BK = Book
CT = Carton
BX = Box
ST = Set
Multiple Order Qty
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Item Description
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
NA
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
GLOSS TEXT
80
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
NA
85
11
NA
NA
NA
NA
HALF
85 x 11
RRD must provide this information
BR pub type specs
Field definitions
ampL04032006ampRampP
PackagingOrdering Unit Of Measure
EA = Each
PK = Pack
PD = Pad
RL = Roll
BK = Book
CT = Carton
BX = Box
ST = Set
Multiple Order Qty
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool
100 Gloss Text
100 Text
10pt C1S Cover
10pt C2S Cover
10pt C2S Text
10pt Text Stock
110 White Index
12pt C1S Cover
20 White Opaque Bond
50 Colored Offset
50 White Offset
50 White Opaque
60 Cover Stock
60 White Offset
80 Gloss Cover
80 Gloss Text
8pt C1S White
90 White Index
CoverText Ink
Black
Black + 1 PMS color
Type in PMS color
Black + 2 PMS colors
Type in PMS colors
4 color
4 color over black
4 color + 1 PMS color
Type in PMS color
4 color over black + 1 PMS color
Type in PMS color
4 color + 2 PMS colors
Type in PMS colors
4 color + aqueous
4 color + varnish
dPrint
ContentComp
Split Shipment Indicator Flag
WCSS Item Number
Customer Item Number
Cannot use quote symbol that is----
Producing Plant
Job Number
Replenishing Plant
Plant Code
Product Code
PackagingOrdering UOM
Qty per PackagingOrdering UOM
List Price Per Ea
Transfer Cost per Ea
Sell Price per Ea
Standard Cost (per Ea)
Min Order Qty (in eaches)
Multiple Order Qty (in Eaches
Chargeback Price
Item Reference 1
Item Reference 2
Revision Field
Max Order Qty (in eaches)
Sequentially Numbered Item
Sequentially Numbered Item - Details
Priced for Digital or Offset
Content File Location
Item Category Form (F) Book (B)
Item Subtype
Orientation
Sides Printed
CSSJLS Stock Componet
Paper Size Width
Paper Size Length
No of Forms to a Sheet
Page Qty
Sheets Qty
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
of Tabs
Binder Size
Binder Color
Binder Ring Type
Binder Transparency (clearview or matt)
Thermal Tape Color
Trim Size Width
Trim Size Length
Stitching Location
Drilling Size
Drilling Location
Glue Location
Pad
Fold Type
Fold At
Poly
Box
Comments
Cross Reference Item Number 1
Publication Number
Publication Title
PackagingOrdering Unit Of Measure
Qty per PackagingOrdering Unit of Measure
Min Order Qty
Multiple Order Qty
Business Group
Cost Center
Revision Date
Max Order Qty
Black amp Whiteor Color
Item CategoryForm (F) or Book (B)
BindingStitching
Orientation
Sides Printed
Printing Paper Size Width
Printing Paper Size Length
Number of Forms to a Sheet
Page Count of Publication
Number of Sheets Required to Print
CSSJLS Production Stock
Paper Stock Type
Paper Stock Weight
Paper Stock Color
Stack Offset
Tab Size
Number of Tabs Needed
Binder Size
Binder Color
Binder Ring Type
Binder Transparency
Thermal Tape Color
Finished Trim Size Width
Finished Trim Size Length
Stitching Location
Drill Hole Size
Number and Location of Drill Holes
Glue Location
Number of Pages per Pad
Fold Type
Fold At
Number of Pieces per Poly wrap
Number of Pieces per Box
Comments
Part Number
Are these items being setup on dPrint (Yes or No) If yes Inv Mgmt to check Print Management flag on item setup
The contentComp will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item ) The contentcomp must be hardcoded to the Item message Field in WCSS Must be a 10 Digit number that starts with an 8
Required Setting this to yes will allow warehouse product to ship out before the JIT item is completed Setting this to no will hold all warehoused items until the printing of this item is complete Please indicate Y or N Note Each item with a Y will always ship separately even if produced at the same time as like items
Optional 15 Characters Max If the WCSS number provided already exists in the system then Inventory Management will assign a random WCSS number
30 characters maximum
Cannot use quote symbol that is----
Required Which plantPrint Center will produce this item
Required To be provided from the producing plant for JIT su
Required What is the plant code of the plant that has owning rights to the dPrint files If produced at multiple plants there can be only one owning plant
Required What is the plant code of the facility that will produce this item (see Plant and Whse Codes tab below)
Required Enter one of the applicable product
Method of packaging for publication shipmentClick here for explanation of each value in the pull-down
Required This field auto-calculates (transfer cost divided by 5) Used to determine Standard Cost on WCSS (which is 50 of the list price for these product codes)
Required Transfer Cost per orderingpackaging unit of measure
Required Price that will be billed to customer upon order If Price Breaks enter Price Breaks and note them on separate spreadsheet
Required Replacement Cost per Packagingordering UOM
Click here for an explanation of this field otherwise type NA
Optional Used to assist customer with internal Chargebacks to end users (per packagingordering UOM)
IMPORTANT This information must match the DocMan recordClick here for explanation of each value in the pull-down menu
IMPORTANT This information must match the DocMan record
IMPORTANT This information must match the DocMan recordDate on the publication
Click here for explanation of each value in the pull-down menu
Indicate Yes or No Enter Yes if the item is a sequentially numbered item
Describe the details behind the sequentially numbered item such as- Record Sequence Shipped whse will record the sequence numbers that shipped- Ship in Sequence Record required to ship products in particular sequence and the whse records the numbers
Required If PDF is to be retained in the DAS enter DAS in this field if item is part of eCreate or Custom Docs put CUSTOM in this field
Typically a BookClick here for explanation of each value in the pull-down menu
Click here for explanation of each value in the pull-down
Click here for explanation of each value in the pull-down menu
Optional Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book
IMPORTANT Not Trim Size widthThis is the width of the paper on which the publication is printed
IMPORTANT Not Trim Size lengthThis is the length of the paper on which the publication is printed
Click here for explanation of how to determine the information required
Click here for explanation of how to determine the information required
Optional Use when product is being printed on Shell Stock Provide warehoused WCSS Item number of product to be used in the production of JIT item
Click here for explanation of how to determine the information required
The pull-down menu lists the most common choicesClick here for a full list of the available choicesIf you use a choice not in the pull-down list type the value in the cell below the pull-down menu
If item uses tabs otherwise NA
If needed otherwise type NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If item used in a binder otherwise NA
If publication is thermal tape bound otherwise NA
Click here to see the available finished trim sizesThe sizes are listed - width x length
Click here to see the available finished trim sizesThe sizes are listed - width x length
If publication is Book [B] and stapled otherwise NA
Click here for a list of possible drill locations
If publication uses padding otherwise NA
If publication is a notepad or message pad otherwise NA
Click here for explanation of each value in the pull-down menu Folding of final document optional
The location(s) of the fold
Click here for explanation of each value in the pull-down menu
Use this column to list- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine if necessaryAlso use to indicate any other production or finishing requirements not provided in previous columnsClick here for an explanation of the available Cover Stock Cover Ink and Text Ink values
List only if pubication is used in manufacturing otherwise leave blank
PK
1
See DocMan for the Cost Center selections associated with each Business Group
Color
B
SADDLE
PORTRAIT
HEAD2HEAD
RRD must provide this information
RRD must provide this information
White
RRD must provide this information
NA
NA
NA
NA
NA
NA
85
11
SIDE
NA
NA
NA
NA
HALF
85 x 11
50
RRD must provide this information
Field definitions
ampL04032006ampRampP
PackagingOrdering Unit Of Measure
EA = Each
PK = Pack
PD = Pad
RL = Roll
BK = Book
CT = Carton
BX = Box
ST = Set
Multiple Order Qty
Separate methods of ordering same item For example if an item is packaged 50 per pad 5 pads per carton You can set the order qty as 50 each (one pad) or 250 each (1 ctn)
Business Group
The business group that the publication supports Your choice here determines the list you choose from for Cost Center
CorporateBusiness Development
Finance
Human Resources
IT
Logistics
Manufacturing
Marketing Commercial
Marketing Europe
Marketing Other
Operations
Order Services
Other
Process Improvement
Procurement
Quality
Sales
Max Order Quantity
Presale items = 100
Postsale items = 5
NOTE You can use other quantities but the delivery may take a bit longer because a system admin must approve it
Item Category - Form (F) or Book (B)
Form (F) = Any publication that is a single sheet (ie 1 or 2 pages) an envelope or carbonless form
Book (B) = Any publication that contains 3 or more pages
BindingStitching
For a Form (F) use
CARBONLESS
CUTSHEET
ENVELOPE
For a Book (B) use
LOOSE
LOOSE -Loose Leaf
PERFECT
PERFECT - Perfect Bound
PLASTCOIL
PLASTCOIL - Plastic Coil (Coil Bound)
SADDLE
SADDLE - Saddle Stitch
STAPLED1
STAPLED1 -1 position
STAPLED1B
STAPLED1B - bottom 1 position
STAPLED2
STAPLED2 - 2 positions
THERMAL
THERMAL - Thermal bound (Tape bound)
THERMALO
THERMALO - Thermal Bound (Tape bound - offline)
WIRE O
Wire O - Double Wire Bound (offline)
Saddle-Stitch Items
20 sheets max on 20 (text and cover)
19 sheets max on 20 (text) and 24 (cover)
18 sheets max on 24 (text and cover)
All page quantities must be divisible by 4
Tape Bound Items
125 sheets max on 20 no cover
120 sheets max wcover (90 index unless indicated otherwise)
Perfect Bound Items
475 sheets max on 20 no cover
470 sheets max wcover (90 index unless indicated otherwise)
Double Wire Bound Items
40 sheets max on 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Coil Bound Items
290 sheets max of 20 (if adding cover deduct equivalent number of pages to equal cover thickness) (90 index unless indicated otherwise)
Sides Printed
Head2Head = Most common Double-sided printing with headers on both pages lining up at the top of the page
Simplex = Single-sided printing
Head2Toe = Least common Double-sided printing with header on one page lining up with the footer on the other page
Number of Forms to a Sheet
Number of publication pages printed on a sheet of paper at the printerFor example if a 4-page 85 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half the Number of Forms to a Sheet = 4Example 2 If a 4-page 55 x 85 publication is printed on the front and back sides of an 85 x 11 sheet of paper that is folded in half the Number of forms to a Sheet = 4
Number of Sheets Required to Print
Number of sheets of paper required to print the publicationFor example if a 16-page 85 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together the Number of Sheets Required to Print = 4Example 4 If a 4-page 55 x 85 publication is printed on the front and back sides of one 85 x 11 sheet of paper that is folded in half the Number of Sheets Required to Print = 1
Paper Stock Type
Description
PLAIN
Bond
ACNTCVR
Accent Cover
BOND3H
Bond (3-hole)
BOOKENV
Booklet Envelope
C1SGLOSS
C1S Gloss Finish
C1SMATTE
C1S Matt Finish
C2SGLOSS
C2S Gloss Finish
C2SMATTE
C2S Matt Finish
CARD
Card Stock
CATLGENV
Catalog Envelope
CATLGENV6
6 Catalog Envelope
COVERCOLOR
Color Cover Copy
CRCKPEEL
Crack N Peel Label
CUSTOM
Custom
CVRFUTURA
Futura Cover
ENV6x9
Standard 6X9 Envelope
ENV9X12
Standard 9X12 Envelope
ETHCERT
Ethicon Certificate
GLOSSCOVER
Gloss Cover
GLOSSTEXT
Gloss Text
HOTSTEXT
Hots Text
INDEX
Index
LABEL80
80 Up Label
MICROPRT
Micro Print
OFFSET
Offset
PART2
2 Part
PART3
3 Part
PART4
4 Part
PART5
5 Part
PART6
6 Part
PERF
12 inch Perfed
PERMMAT
Perm Mat Ad
PRECUTTAB
Pre-Cut Tab
PREPERF
Pre-Perforated
RECYL
Recycled
SE10ENV
10 Standard Envelope
SE10ITENV
10 Inside Tint Envelope
SE9ENV
9 Stanard Envelope
TAG
Tag
TEXT
Text
TEXTCOLOR
Text Color Copy
TEXTFUTURA
Futura Text
TEXTLASER
Text Laser Print
TRANSPRNCY
Transparencies
VELLUM
Vellum
VELLUM3HP
Vellum 3HP
WE10ENV
10 Window Envelope
WE9ENV
9 Windor Envelope
WE9ITENV
9 Inside Tint Window Envelope
Paper Stock Color
Black
Blue
Buff
Canary
Cherry
Clear
Cream
Custom
Goldrenrod
Gray
Green
Ivory
Lavender
Manilla
NCRPinkCanary
NCRWhiteBlue
NCRWhiteBlueCanary
NCRWhiteCanary
NCRWhiteCanaryPink
NCRWhiteCanaryPinkGoldenrod
NCRWhiteGreen
NCRWhiteGoldenrodYellow
NCRWhitePink
NCRWhiteWhite
Opaque
Orange
Orchid
Peach
Pink
Purple
Salmon
Tan
Violet
White
Finished Trim Sizes (listed - width x length)
11 x 17
18 x 24 Poster
24 x 36 Poster
3 x 5
36 x 24 Poster
4 x 6
475 x 7
475 x 775
55 x 85
6 x 4
7 x 9
7385 x 9 (RSI Std)
85 x 11
825 x 10875
825 x 11 (RA product profile std)
8375 x 10875
9 x 12
A4
A5
Other - Custom size listed below
Drilling Locations
1CENTER
1LEFTTOP
1TOPCENTER
2LEFT
2LEFT2TOP
2TOP
2TOP2LEFT
2TOP3LEFT
2TOP5LEFT
2TOP5RIGHT
3BOTTOM
3LEFT
3LEFT2TOP
3LEFT3TOP
3RIGHT
3TOP
3TOP5LEFT
5BOTTOM
5CENTER
5LEFT
5RIGHT
5RIGHT2TOP
5TOP
For TRI fold - select Z or C type
Description
HALF
Half
C
C Fold
DBLEPARLL
Double Parallel
OFFSETZ
Offset Z
SAMPLE
See Sample
SHORT
Short Fold
V
V Fold
Z
Z Fold
Number of Pieces per Poly Wrap
Publication length
Number per Poly Wrap
77 or more pages
1
33 to 76 pages
25
3 to 32 pages
50
1 or 2 pages
100
Comments
CoverText Stock
Spine
100 Gloss Cover
If your publication uses a spine make note of that in the comments field Be sure to include the spine as the last page of your PDF Do NOT include that page as part of the publication page count Because the addition of a spine will create an odd page count in the PDF contact a Super User to submit your publication via PDFdirect with an exception tool