AL5310An attractive range of smalllow cost floodlights withsix beam distributions.Ideal for façade,architectural, areafloodlighting andsecurity lighting.
Lamps up to 150W SON-TD or MBI.
AL5400A range of doubleasymmetric distributionfloodlights, speciallydesigned to provideefficient lighting oflarge open areas,airports, docks,motorway intersectionsand industrialcomplexes.
Lamps up to 2 x 400W MBI; 2 x 400W SONP-T; 1 x 1000W MBI; 1 x 1000W SONP-T.
AM5000A versatile range offloodlights available with 3 beamdistributions,including a flat glassversion with a beamemergence of 60˚ Suitable for allgeneral purposeexterior floodlightingapplications.
Lamps up to 400W MBI; 400W SON-T.
AL5100A double asymmetricdistribution floodlightrange designed forgeneral purpose use.
Lamps up to 400WSON-T or MBI.
AL5210A versatile doubleasymmetric beamfloodlight offering lowlight pollution control.Ideally suited to thelighting of multi-usesports areas, tenniscourts and generalexterior applications.
Lamps up to 1000W SON-T; 1000W MBI.
IP65Page 4.4
IP65 Page 4.6
4.1
floodlighting - index
Page 4.9IP65
Page 4.7
Page 4.10
Page 4.12IP65
AL5600Floodlight for use with HID lamps up to2000W. Suitable forlighting sports fields,dock yards,marshalling yardsand most large arealighting applications.
Lamps up to 2000W SON-T; 2000W HQI
AM5011/12 ONLY
IP65
IP65
AL5700 Challenger ®1A double asymmetricdistribution floodlightrange, speciallydesigned for lightingoutdoor sportsgrounds, smallersports stadiums andlarge open areaswhere light pollutioncontrol is an essentialrequirement.
Lamps up to 600W SON-T, 1000W SON-TD, 2000W MHN-TD
AL5800 Challenger ®2An asymmetric distributionfloodlight range usedprimarily for sidelighting sportssystems includingroof mounting instadiums.
Lamps up to 2000WHQI; 2000W MHD.
AL5900 Challenger ®3A symmetrical distributionfloodlight range, speciallydesigned for lightinglarge sports stadiausing corner mastsystems. Of highperformance andcompact design,these floodlightsprovide precisionoptical control coupledwith reduced weight andwindage compared toconventional stadium floodlighting.
Lamps up to 2000W HQI; 2000W MHD.
Page 4.14
4.2
GUIDE TO LOGOS
The following logos are provided toassist the customer towards making aninformal decision over the specificationof the luminaire.
SECURITY
Luminaires denoted with this logo are ideally suited to securityapplications.
ULOR
Floodlights; the % of upward lightproduced is given at the specificelevation stated and is themaximum working elevation thatthe floodlight would be set to innormal practice.
ABACUS LIGHTCONTROL SYSTEM
Floodlight ranges that are denotedwith this logo possess specificdesign characteristics thateffectively control the three keyforms of obtrusive light, these beingupward light, overspill and glare.
IP RATING
The IP rating indicates the level ofprotection against ingress ofmoisture or dust and is definedby 2 digits. The first digit relatesto dust protection, the seconddigit relates to water protection.
IP65
National Inspection Council forElectrical Installation Contracting
APPROVED CONTRACTOR
Page 4.20IP65
IP65
Page 4.18IP65
®
4.3
floodlighting - ordering details
5 Quantity of floodlights required.
6 Floodlight reference number –
made up as the example below.
7 Supply voltage and frequency.
8 Abacus floodlights are supplied in
either integral or remote control
gear versions. For floodlights
supplied with remote control gear
this can be provided either as
loose components or pre-wired on
gear trays (extra cost). Please
specify which is required.
When ordering floodlights the
following information will enable us
to identify the product you require
both quickly and accurately. By using
our reference numbering system,
errors can be avoided ensuring that
the right products are delivered to
the correct address.
1 Your company name, contact
name and telephone number.
2 Your order number.
3 Invoice address.
4 Delivery address (if different
to above) and, if notification of
delivery is required in advance,
contact name and telephone
number.
9 Most floodlights are provided
with non cut-out ignitors and
standard ballasts.
Ballasts protected with internal
thermal overload switches and
ignitors with cut-out facility are
available at extra cost. Please
specify which is required.
*Please refer to product pages which show details of choices available.
*Lamp Type
THD TUNGSTEN HALOGEN
SE SON-E
ST SON-T
SPT SON P-T
STD SON T-D
CMD CMD-TD
MU MBF-U
MI MBI
MIF MBIF
MIL MBIL
HQI HQI-TS2000 WDS
HQI-TS1000 WDS
MHN/LA MHN-LA-2000
MHN/SA MHN-SA-2000
HQI/NL HQI-TS2000WNL
*Lamp Wattage*Basic Model Number
AM5006 400 ST
4.4
floodlighting - AM5000 series
A versatile range of floodlights available in 3
beam distributions for use with high pressure
discharge lamps up to 400W. Suitable for
use in all general purpose exterior lighting
applications.
Featuring:
• High pressure die-cast aluminium
body and front cover frame, finished
light grey (RAL 7032) polyester powder
coating.
• Electropolished, anodised and sealed
aluminium reflector.
• E-40 lamp holder with adjustable assembly
for centralising the lamp within the
floodlight.
• Toughened front glass
• Galvanised steel stirrup with protractor for
setting elevation angle.
• Access to lamps and control gear via
opening the hinged front cover.
• Integral gear versions incorporate a
galvanised steel control gear tray
that is removable for ease of
maintenance.
• Versions AM5009/10, AM5006/8 include
a baffle above the lamp to reduce glare
and improve performance.
• Versions AM5011/12 are Flat Glass with a
beam emergence of +60˚ for low light
pollution applications.
Accessories available:
- Cowl AM9007 for reduced light pollution.
- Front guard AM9005.
- Vertical louvres AM9006 (0.77kg).
- Polycarbonate front shield AM9040
N.B: Accessories only allow single fitting to
each floodlight.
IP65
AM5006/8
AM5011/12
AM5009/5010
AM5011/12
floodlighting - AM5000 series
4.5
AM5000 series floodlights are available in 3 beam distributions:-
The large range of beam options allows complete versatility of application from
lighting areas to floodlighting buildings.
Double Asymmetric Wide Medium Symmetric Narrow
Double Asymmetric Wide AM5011/12Asymmetric Medium 5009/10Symmetric Narrow AM5006/8
Narrow SymmetricAM5006/8
Medium AsymmetricAM5009/10
Double Asymmetric WideAM5011/12
Vertical Adjustment
Ipk
Floodlight Elevation = Medium/NarrowFloodlight Elevation = -60° Double Asymmetric Wide
60°Ipk
°140° 140°
°
°°
Dimensions in mm
175
435
600
540
150
2 x 15Ø 21Ø
Model Lamp Wattage and Type Lamp Holder Description Weight (kg)
AM5006 150W SON-T E-40 Narrow symmetric 14.0250W SON-T E-40 beam/ 15.0400W SON-T E-40 integral gear 17.0250W MBI E-40 15.0400W MBI E-40 15.0
AM5008 150/250/400W SON-T E-40 Narrow symmetric beam/ 9.0250/400W MBI loose gear 9.0
AM5009 150W SON-T E-40 13.0250W SON-T E-40 15.0400W SON-T E-40 16.0250W MBI E-40 15.0400W MBI E-40 15.0
AM5010 150/250/400W SON-T E-40 Medium beam/ 9.0250/400W MBI E-40 loose gear 9.0
AM5011 150W SON-T E-40 Double asymmetric, 13.0250W SON-T E-40 wide beam (60˚) 15.0400W SON-T E-40 /integral gear 16.0250W MBI E-40 15.0400W MBI E-40 15.0
AM5012 150/250/400W SON-T E-40 Double asymmetric, wide 9.0250/400W MBI E-40 beam (60˚)/loose gear 9.0
Please specify mains voltage requirements. Weights shown include control gear. Windage 0.230m2
4.6
IP65
floodlighting - AL5100 series
A double asymmetric distribution floodlight
range designed for general purpose use.
Lamp versions; 100W, 150W, 250W,
400W SONP-T or MBI
Featuring:
• Die cast aluminium body finished in
black polyester powder coating.
• Toughened front glass secured by
stainless steel screws and extruded
aluminium clips.
• Integral rear gear box.
• Double asymmetric reflector system.
• Sealed to IP65.
Product Ref Lamp Wattage and Type Lamp Holder Beam Type Description Weight (Kg)
AL5104 100W SONP-T E-40 Double Asymmetric Integral rear Gear Box 7.5150W SONP-T E-40 Double Asymmetric Integral rear Gear Box 7.6
AL5107 250W SONP-T/MBI E-40 Double Asymmetric Integral rear Gear Box 9.2400W SONP-T/MBI E-40 Double Asymmetric Integral rear Gear Box 10.3
Please specify mains voltage and requirements. Weights shown include control gear. Windage 0.12m2.
1503x Ø9
300
40
min
500
min 10min 90°
min 300
330
480
400
max 180°
Dimensions in mm
Stirrup Mount (M8 Fixing)
250W / 400W ST
floodlighting - AL5210 series
4.7
IP65
• Steel stirrup with secure locking
system and general elevation
protractor. Stirrup adjustment 180°
max.
• FLAT GLASS operation with beam
emergence at +45° forward throw.
• Remote control gear with integral
ignitor.
• Anti-vacuum device system fitted
to 1KW versions as standard.
• Optional Cowl accessory (AL5299).
A versatile double asymmetric beam
floodlight offering low light pollution
control. Ideally suited to the lighting of
multi-use sports areas, tennis courts
and general exterior applications.
Designed for use with single ended
metal halide lamps or high pressure
sodium lamps up to 1000W max.
Featuring:
• Body of high pressure die cast
aluminium, finished in light grey
polyester powder coating (RAL 9006)
• Toughened front glass secured by six
extruded aluminium clips
• Silicone rubber gaskets for ingress
protection to IP65
• Double Asymmetric Reflector systems
(Medium & Wide) in polished and
anodised aluminium.
• Integral baffle, ensuring excellent
glare limitation and increased
performance.
• Rear mounted electrical
connection box.
AL5218AL5216
4.8
floodlighting - AL5210 series
Product Ref Lamp Wattage and Type Lamp Holder Description Weight (Kg)
AL5216 400/600/1000W SON-T E-40 Double Asymmetric Medium 9.9400/1000W MBI 9.9
AL5218 400/600/1000W SON-T E-40 Double Asymmetric Wide 9.9400/1000W MBI 9.9
Weight excludes lamp and control gear. Windage 0.12m2
Easy access for re-lampingvia opening front glass
Max 150°
Max 60°
Max 180°
Max 180°
Min 90°
Min 500
663
429
556
M8 fixing
293
Dimensions in mmDimensions in mm
Stirrup Mount (M8 Fixing)
4.9
floodlighting - AL5310 series
IP65
Product Ref Lamp Wattage and Type Lamp Holder Description Lamp Position Reflector Weight (kg)
AL5311 35W/70W/150W HCI-T G12 Double Horizontal 7.5*70W/150W HCI-TS RX7s Asymmetric 70W/150W HQI-TS RX7s Reflector (Matt)70W/150W SONT-D RX7s
AL5312 35W/70W/150W HCI-T G12 Double Horizontal 7.5*70W/150W HCI-TS RX7s Asymmetric 70W/150W HQI-TS RX7s Reflector (Bright)70W/150W SONT-D RX7s
AL5313 35W/70W/150W HCI-T G12 Asymmetric Horizontal 7.5*70W/150W HCI-TS RX7s Reflector (Matt)70W/150W HQI-TS RX7s70W/150W SONT-D RX7s
AL5314 35W/70W/150W HCI-T G12 Asymmetric Horizontal 7.5*70W/150W HCI-TS RX7s Reflector (Bright)70W/150W HQI-TS RX7s70W/150W SONT-D RX7s
AL5315 35W/70W/150W HCI-T G12 Symmetric Vertical 7.5*Reflector
AL5316 35W/70W/150W HCI-T G12 Symmetric Horizontal 7.5*70W/150W HCI-TS RX7s Reflector70W/150W HQI-TS RX7s70W/150W SONT-D RX7s
*Weight includes lamp and control gear (maximum weight in range). Windage 0.123m2
280
330
436
366
An extensive range of high quality, lowwattage floodlights designed for generallighting of small areas, architecturalfeatures, facades and securityapplications
Available with a range of lamp typesincluding High Pressure Sodium, MetalHalide and HCI-T / HCI-TS up to amaximum of 150W.• Three reflector versions (symmetric,
asymmetric and double asymmetric)• High pressure die-cast body and frame
made from aluminium alloy with apolyester grey finish (RAL7035)
• Toughened front glass, sealed withsilicone gasket
• M20 electrical cable gland• Galvanised steel control gear tray• Anodised and sealed aluminum reflector• Extruded aluminium stirrup• Elevation aiming protractor• Integral control gear• Sealed to IP65
Accessories:
AL5399 Aluminium anti-glare louvre inpolyester grey (RAL7035).
151
280
330
436 36
6
151
Dimensions in mm
IP65
4.10
floodlighting - AL5400 series
A range of double asymmetric distribution
floodlights, specially designed to provide
efficient lighting of large open areas,
airports, docks, motorway intersections and
industrial complexes.
For use with 2x400W or 1KW High Pressure
Discharge lamps (SONP-T:MBI), with remote
control gear (integral ignitor).
Optimum mounting heights 15m to 30m
Featuring:
• Available in 2 beam distributions, narrow
and medium
• Double asymmetric distribution. Beam
emittance angle at +60° when installed
with front glass horizontal
• Die-cast aluminium body, polyester powder
coated over zinc chromate substrate.
Finish metallic grey RAL9006
• Front glass sealed to IP65 via 2 part
silicone gasket
• Tempered safety front glass, hinged to the
body and secured via captive screws and
INOX springs. Glass may be quickly
opened and closed for easy maintenance
• Anti-vacuum device fitted
to body to prevent mechanical stress on
front glass during cooling.
• High performance reflector
in polished and anodised aluminium
• Stirrup in hot galvanised steel. Fixing
ensures flat glass
+/-10° elevation adjustment
• All external screws INOX A2
• Separate connection chamber / ignitor
housing, connected to rear/top of
floodlight body (polyamide 66)
• 2 x 400W lamp versions as standard,
provide added safety should 1 lamp fail
• Max. ambient temperature +40°C in use
4.11
floodlighting - AL5400 series
1140
max 90º
AL5400 floodlight with double
Asymmetric light distribution
Electrical installation via rear/top
connection box.
Connection box houses ignitor
Electrical installation via rear/top
connection box.
Connection box houses ignitor
680 770
260680 820
320
10º max
10º max
Product Ref Lamp Wattage and Type Lamp Holder Description Weight (Kg)
AL5401 2x400W SONP-T or MBI E-40 Narrow 23.0
AL5402 2x400W SONP-T or MBI E-40 Medium 23.0
AL5403 1000W SONP-T or MBI E-40 Narrow 23.0
AL5404 1000W SONP-T or MBI E-40 Medium 23.0
Please specify mains voltage and requirements. Weights shown include ignitor. Windage 0.12m2.
Floodlight elevation
Horizontal +/- 10˚
2 x 400W SONP-T
680 770
680
320
1140
820
260
Dimensions in mm
420
4.12
floodlighting - AL5600 series
Floodlight for use with HID lamps (1000W &
2000W). Suitable for lighting sports fields,
dock yards, marshalling yards and most large
area lighting applications.
Lamps: 1000W SON-T. (Vs 240V)
1000W HQI / 2000W HQI. (Vs 415V)
Optimum mounting heights 15m to 30m
Featuring:
• Body and rear cover in pressure die cast
aluminium, finished in grey polyester
powder.
• Hot dipped galvanised steel stirrup.
• Toughened front glass, retained with
stainless steel clips.
• Silicone gasket sealing.
• Thermoplastic high temperature lamp
holder.
• Electrical connection box (nylon) mounted
on stirrup.
• Aluminium reflector 99.85% pure,
brightened and anodised.
• Side elevation protractor.
• IP65.
IP65
Asymmetric Beam
Double Asymmetric Beam Symmetric Beam
4.13
floodlighting - AL5600 series
Model References Lamp Wattage and Type Lamp Holder Description Weight (kg)
AL5601 2KW HPI-T E40 Asymmetric Beam 19.0
AL5602 1KW HPI-T E40 Asymmetric Beam 19.0
AL5603 HQI-TS2000WNL K12s-7 Asymmetric Beam 19.0
AL5604 MHN-LA1000/842 X528 cable Asymmetric Beam 19.0
AL5605 1KW SON-T E40 Asymmetric Beam 19.0
AL5606 2KW HPI-T E40 Double Asymmetric Beam 19.0
AL5607 1KW HPI-T E40 Double Asymmetric Beam 19.0
AL5608 HQI-TS2000WNL K12s-7 Double Asymmetric Beam 19.0
AL5609 MHN-LA1000/842 X528 cable Double Asymmetric Beam 19.0
AL5610 1KW SON-T E40 Double Asymmetric Beam 19.0
AL5611 HQI-TS2000WDS K12s-7 Symmetric Beam 19.0
AL5612 HQI-TS1000WDS K12s-7 Symmetric Beam 19.0
Please specify mains voltage and requirements. Weights shown include ignitor. Windage 0.238m2.
Dimensions in mm
4.14
floodlighting - Challenger ®1 AL5700 series
A double asymmetric distribution, Flat Glass
floodlight range, specially designed for
lighting outdoor sports grounds, smaller
sports stadiums and large open areas where
light pollution control is an essential
requirement.
For use with double ended 2KW or 1KW
Metal Halide; double ended lamps or single
ended up to 600W.
Featuring:
• Body of high-pressure die cast aluminium,
finished in light grey (RAL7035), Polyester
powder coating
• Medium and wide beam, asymmetric light
distributions.
• Reflector system of high purity, polished
and anodised aluminium. Incorporating an
internal baffle to improve efficiency and
reduce glare.
• Toughened front glass, secured by
extruded and anodised aluminium clips.
• Galvanised steel stirrup, with additional
locking screws.
• IP65; with silicone rubber gasketing.
• Electrical connection box (IP65) housing
Ignitor, located on side of stirrup.
• Easy access for re-lamping via opening of
the rear cover. Positive closure via large
stainless steel catch.
• Designed to accept a large range of
double ended 2KW & 1KW lamps.
• Variable COWL accessory AL5721 (light
grey) to limit overspill and prevent Sky
Glow. Variable COWL accessory AL5722
(black) for additional backward overspill
control. Variable cowls provide Flat Glass
at 65°/70°/75° beam elevations.
IP65®
4.15
floodlighting - Challenger ®1 AL5700 series
Abacus Light Control System
A combination of efficient lighting
design and careful floodlight design has
rewarded Abacus with an international
reputation for pioneering high
performance floodlighting combined
with effective control of light pollution.
Specific to Challenger® 1 the
Abacus Light Control System consists
of a series of complementary measures
to effectively control light pollution.
1. Double Asymmetric Reflector
The double asymmetric reflector is
designed to ensure full flow of light over
the lit area from each floodlight. With
the main beam emitted from the
floodlight at an angle of 45˚ forward
from the normal to the front glass, it
results in a flatter appearance (FIG 1).
The benefit is that less of the reflector is
visible to spectators and onlookers,
resulting in low glare to the surrounding
locality.
2. Internal Baffle
The internal baffle re-directs upward
stray light back into the floodlight beam,
providing increased efficiency. At angles
above the beam baffle shields direct
lamp glare. (FIG 2)
3. Optional Cowl (Skirt) Accessory
The final element of the light control
system, an adjustable cowl fitting,
provides additional control of upward
light and direct limitation of overspill.
The floodlight and cowl combined
achieves an effective Flat Glass profile
at a beam elevation of 65˚/70˚/75˚.
(FIG 3) This effectively provides full cut
off at the horizontal.
Using a cowl achieves better
management of overspill. However,
cowls will produce a marginal increase
in backward illumination due to
reflectance off the back edge. This
effect is eliminated by the use of a black
surface finish to the cowl. (FIG 4)
45°
IPK
65°/70°/75°
HORIZONTAL
HORIZONTAL
BACKWARD LIGHTBLACK
INNER FACE
FIG 1
FIG 3
FIG 2
FIG 4
®
Lamp technical data (2KW) OSRAM PHILIPS PHILIPS
Lamp Ref: HQI-TS2000WNL MHN-LA2KW400V/842 MHN-LA2KW400V/956
Colour Temperature: 4100K 4200K 5600K
Lamp Lumen Output: (Initial lm) 225,000 l.Lm 220,000 l.Lm 190,000 l.Lm
Lamp Current: 10.7A 9.6A 10.3A
Supply Circuit 3-Phase: 380/400/415V 380/400/415V 380/400/415V
Supply Current: Starting: 13A 8.3A 8.3A
Running: 6.5A 5.6A 5.6A
Total Circuit Power: 2180W 2105W 2113W
RA: 65 85 90
4.16
floodlighting - Challenger ®1 AL5700 series
267
280
Model No. Lamp Wattage and Type Lamp Manufacturer Lamp Holder/support Description
AL5706 HQI-TS2000WNL Osram K12s-7 cable Medium Beam
AL5707 2KW MHN-LA / 842 & 956 Philips X528 cable Medium Beam
AL5709 1KW MHN-LA / 842 & 956 Philips X528 cable Medium Beam
AL5711 600W SONP-T Osram (plus)
Philips (super) E40 Medium Beam
AL5713 600W SONP-T Osram (plus)
Philips (super) E40 Wide Beam
AL5714 HQI-TS2000WNL Osram K12s-7 cable Wide Beam
AL5715 2KW MHN-LA / 842 & 956 Philips X528 cable Wide Beam
AL5717 1KW MHN-LA / 842 & 956 Philips X528 cable Wide Beam
Weight: 16.87 Kg (with ignitor and without lamp) Windage: 0.136 m2 @ 75° elevation
Lamp Illustrations
MHN-LA SON-PT HQI
IP65
Dimensions in mm
®
341 268
132
21mm
4.17
floodlighting - Challenger ®1 AL5700 series
Simple lamp changing via opening back cover using a clip system ensures ease of maintenance.
Two aiming methods:1. In-built line of sight aiming feature2. Separate aiming protractor ensures optimum targeting of individual floodlights to
achieve the desired lighting levels.
Aiming
Relamping
line of sight
Austria RegD No 38431
Benelux RegD No 32055-01
Canada RegD No 92129
China RegD No 00301204.2
Denmark RegD No MR2000796
Eire RegD No D13051
France RegD No 001139
Germany RegD No 49911610.0
Greece RegD No 6000682
Hong Kong RegD No 9911680.2M001
India RegD No 182049
Spain RegD No 147.552
Sweden RegD No 66654
Switzerland RegD No 126663
UK RegD No 2086396
USA Patent No D441889
Registered design in the
following countries
4.18
floodlighting - Challenger ®2 AL5800 series
An asymmetric distribution floodlight range
used primarily for side lighting sports
systems including roof mounting in stadiums.
• Body of high-pressure die cast aluminium,
finished in light grey (RAL7035),
Polyester powder coating.
• Reflector system of high purity, polished
and anodised aluminium. Incorporating an
internal baffle to improve efficiency and
reduce glare.
• Toughened front glass, secured by
extruded and anodised aluminium clips
with silicone rubber pads.
• Galvanised steel stirrup, with additional
locking screws.
• IP65; with silicone rubber gasketing.
• Electrical connection box (IP65) housing
Ignitor, located on side of stirrup.
• Easy access for re-lamping via opening of
the rear cover.
• Positive closure via large stainless steel catch.
• Designed to accept double ended, short
arc 2KW & 1KW Metal Halide lamps.
• Dual provision on side of floodlight body to
attach a Gun Sight aiming device to allow
accurate beam alignment.
Aiming
line of sight
Optical gun sight fixings are incorporated ensuring simplealignment and attachment of gun sight.
IP65
Visor accessory AL5922 to reduceupward light and glare.
4.19
floodlighting - Challenger ®2 AL5800 series
541
270
361
70
484
360
276
484
370 252
622
Dimensions in mm
Model No. Lamp Wattage and Type Lamp Manufacturer Lamp Holder Support Description
AL5801 HQI-TS2000WNL Osram K12s-7 Narrow
AL5802 HQI-TS2000WNL Osram K12s-7 Medium
AL5803 HQI-TS2000WNL Osram K12s-7 Wide
AL5804 MHN-LA2KW/842 & 956 Philips X528 Cable Narrow
AL5805 MHN-LA2KW/842 & 956 Philips X528 Cable Medium
AL5806 MHN-LA2KW/842 & 956 Philips X528 Cable Wide
AL5807 MHN-LA1KW/842 & 956 Philips X528 Cable Narrow
AL5808 MHN-LA1KW/842 & 956 Philips X528 Cable Medium
AL5809 MHN-LA1KW/842 & 956 Philips X528 Cable Wide
Weight 15.28kg (with ignitor & without lamp). Windage 0.196m2 @70˚elevation.
Lamp technical data (2KW) OSRAM PHILIPS PHILIPS
Lamp Ref: HQI-TS2000WNL MHN-LA2KW400V/842 MHN-LA2KW400V/956
Colour Temperature: 4100K 4200K 5600K
Lamp Lumen Output: (Initial lm) 225,000 l.Lm 220,000 l.Lm 190,000 l.Lm
Lamp Current: 10.7A 9.6A 10.3A
Supply Circuit 3-Phase: 380/400/415V 380/400/415V 380/400/415V
Supply Current: Starting: 13A 8.3A 8.3A
Running: 6.5A 5.6A 5.6A
Total Circuit Power: 2180W 2105W 2113W
RA: 65 85 90
Challenger® 2 is a Registered Design (see section 4.23)
4.20
floodlighting - Challenger ®3 AL5900 series
A symmetrical distribution floodlight range,
specially designed for lighting large sports stadia
using corner mast systems. Of high performance
and compact design, these floodlights provide
precision optical control coupled with reduced
weight and windage compared to conventional
stadium floodlighting.
Suitable for use on masts at heights
above 20m, it is an ideal choice for use in new
stadia or in upgrading existing installations.
For use with double ended 2KW or 1KW Metal
Halide lamps.
Featuring:-
• Body of high-pressure die cast aluminium,
finished in light grey (RAL7035),
Polyester powder coating.
• Extra Narrow, Narrow, Medium and Wide
beam light distributions.
• Reflector system of high purity, polished and
anodised aluminium. Incorporating an internal
baffle to improve efficiency and reduce glare in
Narrow/Medium/Wide versions.
• Toughened front glass, secured by an
aluminium clamping frame.
• Galvanised steel stirrup, with additional locking
screws.
• IP65; with silicone rubber gasketing.
• Electrical connection box (IP65) housing
Ignitor, located on side of stirrup.
• Easy access for re-lamping via opening of the
rear cover. Positive closure via large stainless
steel catch.
• Designed to accept double ended, short arc
2KW & 1KW Metal Halide lamps.
• Dual provision on side of floodlight body to
attach a Gun Sight aiming device to allow
accurate beam alignment.
• A choice of visor accessories, AL5921 half
concentric louvre to reduce upward light,
overspill and glare and AL5922 single
blade visor.
IP65
AL5921Half concentric louvre
AL5922Single Blade Visor
4.21
floodlighting - Challenger ®3 AL5900 series
Lamp technical data OSRAM PHILIPS
Lamp Ref: HQI-TS2000/D/S MHN-SA 2KW 400 V/956
Colour Temperature: 5600K 5600K
Lamp Lumen Output: 200,000 l.Lm 200,000 I.Lm
Lamp Current: 10.3A 11.3A
Supply Circuit 3-Phase: 380/400/415V 380/400/415V
Supply Current:
Starting: 9A 11A
Running: 6A 6.6A
Total Circuit Power: 2105W 2136W
RA: 93 90
4.22
floodlighting - Challenger ®3 AL5900 series
IP65
Model No. Lamp Wattage and Type Lamp Manufacturer Lamp Holder/support Description
AL5901 2KW HQI-TS 2000WDS Radium / Osram K12s-7 cable Narrow Beam
AL5902 2KW HQI-TS 2000WDS Radium / Osram K12s-7 cable Medium Beam
AL5903 2KW HQI-TS 2000WDS Radium / Osram K12s-7 cable Wide Beam
AL5904 1KW HQI-TS 1000WDS Radium / Osram K12s-7 cable Narrow Beam
AL5905 1KW HQI-TS 1000WDS Radium / Osram K12s-7 cable Medium Beam
AL5906 1KW HQI-TS 1000WDS Radium / Osram K12s-7 cable Wide Beam
AL5907 MHN-SA 2KW 400 V/956 Philips X830/rod Narrow Beam
AL5908 MHN-SA 2KW 400 V/956 Philips X830/rod Medium Beam
AL5909 MHN-SA 2KW 400 V/956 Philips X830/rod Wide Beam
AL5910 MHN-SA 2KW 400 V/956 Philips X830/rod Extra Narrow Beam
Weight: 15.28 Kg (with ignitor and without lamp) Windage: 0.196 m2 @ 70° elevation
Lamp IllustrationsHQI-TS MHN-SA
484
370 252
622
276
541
360
Dimensions in mm
AL5921
Half Concentric Louvre
AL5922
Single Blade Visor
AL5931
Gunsight Aiming Unit
(Gunsight, mounting block & fixings)
4.23
Aiming
Optical gun sight fixings are incorporated ensuring simple alignment
and attachment of AL5931 gun sight aiming unit.
Relamping
Simple lamp changing via opening back cover using
a clip system ensures ease of maintenance
line of sight
Austria RegD No 38432
Benelux RegD No 32055-02
Canada RegD No 92130
China RegD No 00301207.7
Denmark RegD No MR2000813
Eire RegD No D13052
France RegD No 001139
Germany RegD No 49911610.0
Greece RegD No 600682
Hong Kong RegD No 9911680.2M002
India RegD No 182048
Italy RegD No 80.023
Korea RegD No 271533
Portugal RegD No 29416
Spain RegD No 147.552
Sweden RegD No 66653
Switzerland RegD No 126663
UK RegD No 2086397
USA Patent No D440338
Registered design in the
following countries
(Challenger ®2 & Challenger ®3 )
Accessories
floodlighting - Challenger ®3 AL5900 series
AL5921Half concentric louvre
AL5922Single Blade Visor
4.24
floodlighting - photometric details
AM5011/12 400W ST
AM5009/10 400W ST AL5107 250W ST
0
(cd/
K.L
m)
100
200
300
400
500
600
700
800
H V
Luminous Intensity Diagram Peak Intensity : 745 cd/K.Lm
-90° -70° -50° -30° -10° 0° 10° 30° 50° 70° 90°
0° - 90° 100° - 270°
0-90° -60° -30° 0° 30° 60° 90°
cd/K
.Lm
200
400
600
800
1000
1200
1400
1600
1800
2000
0° - 180° 90° - 270°
AM5006/8 400W ST
0-90° -60° -30° 0° 30° 60° 90°
cd/K
.Lm
200
300
700
800
900
600
500
400
100
600
400
200
0-90 -30 30
cd/K
Lm
Angles
-60 600 90
0° - 180° 90° - 270°
Medium
90° - 270° 0° - 180°(Through ipk)
+
-
- +
90°
0°
270°
180°
+
-
- +
90°
0°
270°
180°
+
-
- +
90°
0°
270°
180°
+
-
- +
90°
0°
270°
180°
4.25
floodlighting - photometric details
AL5107 400W ST AL5218 400W MBI
600
400
200
100
0-90 -50 -30 0 10 70 90
cd/K
Lm
Angles
300
500
-70 5030-10
600
400
200
0-90 -30 30
cd/K
Lm
Angles
-60 600 90
0° - 180° 90° - 270°
AL5401 2x400W ST AL5603 1 x 2kW HQI-TS 2000WNL
AL5402 2x400W ST
cd/Klm
600
400
200
-60º -30º 0º 30º 60º
MediumST 2x400W
800
90° - 270° 0° - 180°(Through ipk)
90° - 270° 0° - 180°(Through ipk)
-60º -30º 0º 30º 60º
750
500
250
1000
cd/KlmNarrowST 2x400W
+
-
- +
90°
0°
270°
180°
+
-
- +
90°
0°
270°
180°
+
-
- +
90°
0°
270°
180°
Applies to both AL5401 and AL5402
90°
0°
270°
180°
90° - 270° 0° - 180°(Through ipk)
0-90° -50° -30° 0° 30° 50° 90°
cd/K
.Lm
100
200
300
400
500
600
700
800
-10° 10°-70° 70°
4.26
floodlighting - photometric details
AL5715 HQI-TS 2000WNL/MHN-LA 2000W AL5707 HQI-TS 2000WNL/MHN-LA 2000W
0° - 180° 90° - 270°
1200
800
400
200
0-90 -50 -30 0 10 70 90
cd/K
Lm
Angles
600
1000
-70 50
V
H
30-10
0° - 180° 90° - 270°
1200
800
400
200
0-90 -50 -30 0 10 70 90
cd/K
Lm
Angles
600
1000
-70 5030-10
V
H
Asymmetric Beam-MediumSymmetric Beam-Wide
AL5903 HQI-TS 2000W/MHN-SA 2KW
AL5901 HQI-TS 2000W/MHN-SA 2KW
AL5801 HQI-TS 2000WNL/MHN-LA 2KW842&956
AL5802 HQI-TS 2000WNL/MHN-LA 2KW842&956
300
0-90 -50 -30 0 10 70 90
cd/K
Lm
Angles
2100
-70 50
V
H
30-10
600
900
1200
1500
1800
2400
2700
0° - 180° 90° - 270°
1300
0-90 -50 -30 0 10 70
9100
-70 50
V
H
30-10
2600
3900
5200
6500
7800
10400
11700
cd/K
Lm
Angles
90
Symmetric Beam-Narrow
Symmetric Beam-Narrow
Symmetric Beam-Narrow
AL5803 HQI-TS 2000WNL/MHN-LA 2KW842&956
Symmetric Beam-Narrow
90°
0°
270°
180°
+
-
- +
90°
0°
270°
180°
+
-
- +
90°
0°
270°
180°
90°
0°
270°
180°
90° - 270° 0° - 180°(Through ipk)
-90° -50° -30° 0° 30° 50° 90°-10° 10°-70° 70°0
200
400
600
800
1000
1200
1400
1600
cd/K
.Lm
0
200
400
600
800
1000
1200
-90° -50° -30° 0° 30° 50° 90°-10° 10°-70° 70°
cd/K
.Lm
-90° -50° -30° 0° 30° 50° 90°-10° 10°-70° 70°0
cd/K
.Lm
100
200
300
400
500
600
700
800
900
Abacus Lighting Limited, Sutton-in-Ashfield, Nottinghamshire NG17 5FT, England.
Telephone: (+44) 01623 511111. Fax: (+44) 01623 552133.
Email: [email protected] http://www.abacuslighting.com
©04/2004 Abacus Lighting Limited Flood/3M/McC
As Abacus maintains a policy of continuous development and improvement of its products,
the right to amend any part of the specifications is strictly reserved.
National Inspection Council forElectrical Installation Contracting
APPROVED CONTRACTOR
BS EN ISO 9001:2000BS EN ISO 14001 :1996