Date post: | 03-Jan-2016 |
Category: |
Documents |
Upload: | scaner-man |
View: | 79 times |
Download: | 3 times |
[233]W E L D I N G C O N S U M A B L E S C A T A L O G
SUBMERGED ARC
CONSUMABLESSAW
68281_233_288_ACG.indd 233 3/30/10 2:20 PM
[234] T H E L I N C O L N E L E C T R I C C O M P A N Y
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Submerged Arc (SAW) FluxProduct Name& AWS Class Key Features Packaging Available
700 Series Active Flux PaperBag
PlasticBag
SteelDrum
Lincolnweld® 760(EN 760 – S A MS 1; EN 760 – S A CS 1)
•Highly active flux for handling rust and mill scale•Helps resist porosity caused by arc blow•Slow freezing slag for good weld appearance
Lincolnweld® 761(EN 760 – S A MS 1; EN 760 – S A CS 1)
•Manganese alloying and carbon reducing flux designed to provide superior crack resistance•Slow freezing slag for a wide, flat weld•Excellent resistance to cracking in single pass applications
Lincolnweld® 780(EN 760 – S A AB 1; EN 760 – S A AR 1)
•Industry standard for submerged arc welding applications•Fast freezing slag for easy removal and minimized spilling
on circumferential welds•When paired with Lincolnweld® L-61 it is recommended
for up to three pass welding applications
Lincolnweld® 781(EN 760 – S A ZS 1)
•Features fast follow characteristics that allow for uniform welds at high speeds without undercut or voids•Recommended for high speed, limited pass welding on
clean plate and sheet steel
800 Series Neutral Flux PaperBag
PlasticBag
SteelDrum
Lincolnweld® 860(EN 760 – S A AB 1)
•Industry standard for submerged arc welding applications•Excellent operating characteristics in a variety of general
welding applications •Capable of producing weld deposits with impact toughness exceeding27J(20ft•lbf)at-40°C(-40°F)with Lincolnweld® L-61
Lincolnweld® 865(EN 760 – S A AR 1; EN 760 – S A AB 1)
•General purpose flux designed to weld butt joints and flat and horizontal fillets•When used with Lincolnweld® L-50 or L-61, it is capable of producing480MPa(70ksi)tensilestrengthafterstressrelief•Small loss of strength when used in the stress-relieved
condition
Lincolnweld® 880(EN 760 – S A AS 1; EN 760 – S A FB 1)
•Can be used for both joining and hardfacing welding•Optimal bead appearance when used with solid low alloy
steel electrodes with a minimum of 0.20% silicon•Use with both solid and flux cored wires
Lincolnweld® 880M(EN 760 – S A FB 1)
•A basic flux which features industry proven results in multiple pass applications•Recommended for welding with solid mild steel and low
alloy electrodes, as well as Lincoln’s LAC series of low alloy flux-cored electrodes•Good deep groove slag removal
Selection Guidesubmerged arc
68281_233_288_ACG.indd 234 3/30/10 2:20 PM
[235]W E L D I N G C O N S U M A B L E S C A T A L O G
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Submerged Arc (SAW) FluxProduct Name& AWS Class Key Features Packaging Available
800 Series Neutral Flux PaperBag
PlasticBag
Hermetically Sealed Pail
Lincolnweld® 882(EN 760 – S A AS 1; EN 760 – S A AS 2)
•Designed for a variety of welding applications and is known for providing consistent mechanical properties•Recommended for stainless steel welding and can be
paired with both mild and low alloy steel electrodes
Lincolnweld® 888(EN 760 – S A FB 1)
•Designed for use in critical applications•Recommended for joining mild steel and low alloy
steels in as-welded and stress-relieved applications•LowH4diffusiblehydrogenlevels
Lincolnweld® 8500(EN 760 - S A FB 1)
•Capable of providing impact properties necessary for thick weld joints from root to cap pass •Operates well on AC and multiple arcs with good
resistance to nitrogen porosity •Capable of producing weld deposits with impact propertiesexceeding27J(20ft•lbf)at-62°C(-80°F)
Lincolnweld® MIL800-H(EN 760 - S A CS 1; EN 760 - S A FB 1)
•Capable of providing industry leading H2 diffusible hydrogen levels•Designed for low temperature applications•Recommended for both single and multiple arc
welding of both butt and fillet welds
Special Neutral Flux PaperBag
PlasticBag
Hermetically Sealed Pail
Lincolnweld® 960(EN 760 - S A AB 1)
•Low cost, general purpose flux designed to weld butt joints and both single and multiple pass fillets•Recommended for automatic and semiautomatic
submerged arc welding•A versatile, cost-effective flux that can be used with
many alloy systems
Lincolnweld® 980(EN 760 - S A AB 1; EN 60 - S A AR 1)
•Combines many of the features of the 700 and 800 series fluxes and is ideal for semiautomatic submerged arc welding•Exceptional resistance to flash-through and porosity
caused by arc blow in a variety of applications•Especially high productivity when used with
Lincolnweld® LC-72 wire
Lincolnweld® WTX(EN 760 SA AB 1)
•Neutral submerged arc welding flux designed to meet the specific requirements of wind tower welding applications •Recommended for use with Lincolnweld® L-61
electrode on both longitudinal and circumferential seam welds •Capable of producing weld deposits with impact propertiesexceeding27J(20ft•lbf)at-62°C(-80°F)
Selection Guidesubmerged arc
68281_233_288_ACG.indd 235 3/30/10 2:20 PM
[236] T H E L I N C O L N E L E C T R I C C O M P A N Y
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Submerged Arc (SAW) FluxProduct Name& AWS Class Key Features Packaging Available
Flux for Seam Welding of Pipe PaperBag
PlasticBag
Hermetically Sealed Pail
Bulk Bag
Lincolnweld® 761-Pipe(EN 760 S A MS 1; EN 760 S A CS 1)
•Features the chemical composition of 761 with a particle size optimized for seam welding•Low-melting slag system produces wide flat welds
with superior resistance to cracks and pockmarking•Can handle up to 5 arcs or 5,000 amps
Lincolnweld® P223(EN 760 - S A AB 1)
•Industry standard for pipe welding on up to X80 grade pipe•Fast freezing and easily removable slag for excellent
bead profile•Can be used for welding with up to three arcs
Lincolnweld® SPX80(EN 760 SA AB 1)
•Designed to meet the specific requirements of spiral pipe seam welding of up to API X80 grade pipe •High speed welding capability for increased productivity•Capable of producing weld deposits with impact propertiesexceeding27J(20ft•lbf)at-51°C(-60°F)with Lincolnweld® LA-81
Lincolnweld® 995N(EN 760 - S A AB 1)
•A nitrogen limiting flux designed for seam welding of pipe•Recommended for automatic single pass welding
with up to five arcs•Produces welds with minimal buildup and good
penetration
High Performance / Alloy Flux PaperBag
PlasticBag
Hermetically Sealed Pail
Bulk Bag
Lincolnweld® AXXX-10 •An alloy flux designed to produce a 1% nickel-bearing weld deposit•Recommended for use on ASTM A533 Class 1 and
A588 weathering steels when combined with Lincolnweld® L-61
Lincolnweld® MIL800-HPNi(EN 760 - S A CS 1; EN 760 - S A FB 1)
•When used with Lincolnweld® LA-85 the nickel content will increase from a nominal 1% to a minimum 1%•Use on high performance steel applications, including
HPS70W or HPS100W•Capable of producing ultra low H2 diffusible hydrogen
levels on HPS steels
Selection Guidesubmerged arc
68281_233_288_ACG.indd 236 3/30/10 2:20 PM
[237]W E L D I N G C O N S U M A B L E S C A T A L O G
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Submerged Arc (SAW) Solid WireProduct Name& AWS Class Key Features
Diameters Availablein (mm)
Mild Steel 1/16(1.6)
5/64(2.0)
3/32(2.4)
1/8(3.2)
5/32(4.0)
3/16(4.8)
Lincolnweld® L-50(EM13K)
•A low carbon, medium manganese, medium silicon wire•Pair it with Lincolnweld® 980 flux for the best flux/wire
combination when semiautomatic submerged arc welding
Lincolnweld® L-56(EH11K)
•A low carbon, high manganese, very high silicon wire•Can be used with Lincolnweld® 800 series fluxes on weldsrequiring480MPa(70ksi)tensilestrengthinstress relieved conditions
Lincolnweld® L-60(EL12; EN 756: S 1)
•A low carbon, low manganese, low silicon general purpose electrode•Provides the lowest hardness and is best suited for
use with the Lincolnweld® 700 series of active fluxes
Lincolnweld® L-61(EM12K; EN 756: S 2Si)
•Industry standard for submerged arc welding applications•A low carbon, medium manganese, low silicon general
purpose submerged arc electrode
Lincolnweld® L-S3(EH12K; EN 756: S 3Si)
•A low carbon, high manganese, medium silicon electrode designed for use with the Lincolnweld® 800 series of neutral fluxes •Capable of producing weld deposits with impact propertiesexceeding27J(20ft•lbf)at-62°C(-80°F)when used with Lincolnweld® 888, 8500, and MIL800-H neutral fluxes
Lincolnweld® LA-71(EM14K)
•A low carbon, medium manganese, medium silicon electrode containing approximately 0.1% titanium•Small addition of titanium allows deposits to be
stress-relieved with little loss of strength, even with extended stress relief times
Low Alloy 1/16(1.6)
5/64(2.0)
3/32(2.4)
1/8(3.2)
5/32(4.0)
3/16(4.8)
Lincolnweld® L-70(EA1; EN 756: S 2Mo)
•A low carbon, medium manganese, low silicon, 1/2% molybdenum wire used for single or multiple pass welds•A standard choice for pipe fabrication and other limited
pass applications
Lincolnweld® LA-75(ENi1K)
•A low carbon, medium manganese, high silicon, nickel-bearing electrode designed for use with Lincolnweld® neutral fluxes•Suitable for use in applications requiring less than
1% Ni wire composition
Selection Guidesubmerged arc
68281_233_288_ACG.indd 237 3/30/10 2:20 PM
[238] T H E L I N C O L N E L E C T R I C C O M P A N Y
FL
UX
-CO
RE
DS
UB
ME
RG
ED
AR
CS
TA
INL
ES
S &
NIC
KE
LH
AR
DF
AC
ING
Submerged Arc (SAW) Solid WireProduct Name& AWS Class Key Features
Diameters Availablein (mm)
Low Alloy 1/16(1.6)
5/64(2.0)
3/32(2.4)
1/8(3.2)
5/32(4.0)
3/16(4.8)
Lincolnweld® LA-81(EG)
• A low carbon, medium manganese, low silicon, 1/2% molybdenum wire containing small additions of titanium and boron for improved fracture toughness
• Generally used in two run applications for arctic grade line pipe
Lincolnweld® LA-82(EF2)
• Designed especially for high strength applications• Recommended when over 620 MPa (90 ksi) tensile
strength is required in the as-welded condition or when low temperature impact toughness is required in the stress-relieved condition
Lincolnweld® LA-84(EF3; EN 756: S3 Ni1Mo)
• A nickel-bearing electrode with 1/2% molybdenum• Can be used for higher strength weldments where
impact properties exceeding 27 J (20 ft•lbf) at -62°C (-80°F) are required
Lincolnweld® LA-85(ENi5)
• A nickel-bearing wire with 0.2% molybdenum designed for use on weathering steels
• Capable of producing weld deposits exceeding 480-550 MPa (70-80 ksi) tensile strength in the as-welded and stress-relieved conditions
Lincolnweld® LA-90(EA3K)
• A low carbon, high manganese, high silicon, 1/2% molybdenum special purpose wire
• Recommended for seam welding of pipe and for the general welding of high strength plate
Lincolnweld® LA-92(EB2R; EN 12070: Cr Mo1)
• Designed for welding 1 1/4% chromium, 1/2% molybdenum steels in high temperature service applications such as pressure vessels or piping
• The AWS R designator denotes ultra low residuals which will result in a low Bruscato factor (X-factor)
Lincolnweld® LA-93(EB3R; EN 12070: Cr Mo2)
• Designed for high temperature applications such as pressure vessels and piping for 2 1/4% chromium, 1% molybdenum steels
• The AWS R designator denotes ultra low residuals which will result in a low Bruscato factor (X-factor)
Lincolnweld® LA-100(EM2)
• A low carbon, high manganese wire with nickel and molybdenum designed to weld high strength steels such as HY-80 and HSLA-80
• Delivers yield strength greater than 690 MPa (100 ksi)
Selection GuideSUBMERGED ARC
[239]W E L D I N G C O N S U M A B L E S C A T A L O G
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Submerged Arc (SAW) Cored WireProduct Name& AWS Class Key Features
Diameters Availablein (mm)
Mild Steel 5/64(2.0)
3/32(2.4)
1/8(3.2)
5/32(4.0)
Lincolnweld® LC-72(EC1)
•A cored wire designed to increase deposition rates 10-30% when used with 980 flux•Designed to provide optimal bead shape, penetration, and
slag removal in semiautomatic submerged arc welding
Low Alloy 5/64(2.0)
3/32(2.4)
1/8(3.2)
5/32(4.0)
Lincolnweld® LAC-B2(ECB2)
•A cored wire designed to weld with either single or tandem arcs using a neutral flux•Acost-effectivechoicewhenwelding11/4%chromium,
1/2% molybdenum steels where a low Bruscato factor (X-factor)isnotrequired
Lincolnweld® LAC-M2(ECM2)
•Capableofdelivering690MPa(100ksi)yieldstrengthwhenwelded with Lincolnweld® 880, 880M, 888 or MIL800-H fluxes
Lincolnweld® LAC-Ni2(ECNi2)
•A 2% nickel electrode used primarily in weathering steel applications •When used with 888 flux, it can produce impact properties exceeding27J(20ft•lbf)at-73ºC(-100°F)
Selection Guidesubmerged arc
68281_233_288_ACG.indd 239 3/30/10 2:20 PM
[240] T H E L I N C O L N E L E C T R I C C O M P A N Y
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® 760submerged arc (saW) Flux
Recommended Wires
Typical Applications
For Mild Steel Lincolnweld® L-50, L-60, and L-61
�Single pass welding of mild steel
�Flat fillet welds with constant voltage power source
�Highly active flux for handling rust and mill scale
�Helps resist porosity caused by arc blow
�Slow freezing slag for good weld appearance
Product Information
Basicity Index: 0.8Density: 1.2 g/cm3
700 Series Active FluxEN 760 – S A MS 1; EN 760 – S A CS 1
Key Features
FLUX COMPOSITION(1)
%SiO2 %MnO %MgO %CaF2 %Na2O %Al2O3 %CaO % Metal Alloys
Lincolnweld® 760 47 33 17 5 2 2 1 6 max.
(1)See test results disclaimer on pg. 9. (2)Measured with 0.2% offset. NOTE: For the most up-to-date AWS certificates of conformances please visit www.lincolnelectric.com
AWS TEST RESULTS(1)
Flux/Wire Combination
Weld Condition
Yield Strength(2)
Tensile Strength Elongation
(%)Charpy V-Notch
AWS Classification (A5.17/A5.23)MPa (ksi) MPa (ksi) J (ft•lbf) @ °C (°F)
L-50L-60L-61
As-weldedAs-weldedAs-welded
440390410
(64)(57)(59)
550490530
(80)(71)(77)
303028
539869
(39)(72)(51)
-18-29-29
(0)(-20)(-20)
F7A0-EM13KF6A2-EL12
F7A2-EM12K
Packaging
50lb(22.7kg)PlasticBag ED032799
68281_233_288_ACG.indd 240 3/30/10 2:20 PM
[241]W E L D I N G C O N S U M A B L E S C A T A L O G
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
submerged arc (saW) Flux
(1)See test results disclaimer on pg. 9. (2)Measured with 0.2% offset. NOTE: For the most up-to-date AWS certificates of conformances please visit www.lincolnelectric.com
Lincolnweld ® 761
Recommended Wires
Typical Applications
For Mild Steel Lincolnweld® L-50, L-60, and L-61For Low Alloy Steel Lincolnweld® L-70
�Single pass welding of mild steel
�Large fillets with constant current power sources
�Manganese alloying and carbon reducing flux designed to provide superior crack resistance
�Slow freezing slag for a wide, flat weld
�Excellent resistance to cracking in single pass applications
Product Information
Basicity Index: 0.8Density: 1.2 g/cm3
700 Series Active FluxEN 760 – S A MS 1; EN 760 – S A CS 1
Key Features
FLUX COMPOSITION(1)
%SiO2 %MnO %MgO %CaF2 %Na2O %Al2O3 %TiO2 %FeO % Metal Alloys
Lincolnweld® 761 45 19 22 5 2 2 2 1 6 max.
AWS TEST RESULTS(1)
Flux/Wire Combination
Weld Condition
Yield Strength(2)
Tensile Strength Elongation
(%)Charpy V-Notch
AWS Classification (A5.17/A5.23)MPa (ksi) MPa (ksi) J (ft•lbf) @ °C (°F)
L-50L-60L-61L-70
As-weldedAs-weldedAs-weldedAs-welded
480440480550
(69)(64)(70)(80)
590530590640
(85)(75)(85)(93)
29292824
45645458
(33)(47)(40)(43)
-29-29-29-18
(-20)(-20)(-20)(0)
F7A2-EM13K-H8F7A2-EL12
F7A2-EM12K-H8F9A0-EA1-G
Packaging
50lb(22.7kg)PlasticBag ED032765
68281_233_288_ACG.indd 241 3/30/10 2:20 PM
[242] T H E L I N C O L N E L E C T R I C C O M P A N Y
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® 780submerged arc (saW) Flux
Recommended Wires
Typical Applications
For Mild Steel Lincolnweld® L-50, L-60 and L-61
�Single pass welding of mild steel
�Roundabouts with minimal spillage
�Horizontal position welding
� Industry standard for submerged arc welding applications
�Fast freezing slag for easy removal and minimized spilling on circumferential welds
�When paired with Lincolnweld® L-61 it is recommended for up to three pass welding applications
�Excellent bead shape and slag removal
�Good resistance to moisture contamination for reduced porosity
Product Information
Basicity Index: 0.7Density: 1.4g/cm3
700 Series Active FluxEN 760 – S A AB 1; EN 760 – S A AR 1
Key Features
FLUX COMPOSITION(1)
%SiO2 %MnO %MgO %CaF2 %Na2O %Al2O3 %CaO %TiO2 % Metal Alloys
Lincolnweld® 780 9 16 2 11 2 45 1 9 6 max.
AWS TEST RESULTS(1)
Flux/Wire Combination
Weld Condition
Yield Strength(2)
Tensile Strength Elongation
(%)Charpy V-Notch
AWS Classification (A5.17/A5.23)MPa (ksi) MPa (ksi) J (ft•lbf) @ °C (°F)
L-50L-60L-61
As-weldedAs-weldedAs-welded
520440530
(75)(64)(77)
600520600
(87)(76)(87)
273027
658846
(48)(65)(34)
-18-18-29
(0)(0)(-20)
F7A0-EM13KF7A0-EL12-H8
F7A2-EM12K-H8(1)See test results disclaimer on pg. 9. (2)Measured with 0.2% offset. NOTE: For the most up-to-date AWS certificates of conformances please visit www.lincolnelectric.com
Packaging
50lb(22.7kg)Bag550lb(249.5kg)SteelDrum
ED019586ED032007
68281_233_288_ACG.indd 242 3/30/10 2:20 PM
[243]W E L D I N G C O N S U M A B L E S C A T A L O G
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® 781submerged arc (saW) Flux
Recommended Wires
Typical Applications
For Mild Steel Lincolnweld® L-50, L-60, and L-61For Low Alloy Steel Lincolnweld® L-70
�Single pass welding – on clean plate and sheetmetalupto48mm(3/16in)inthickness
�Hot water tanks, metal buildings and other applications requiring high speed welds
�Features fast follow characteristics that allow for uniform welds at high speeds without undercut or voids
�Recommended for high speed, limited pass welding on clean plate and sheet steel
�Good wetting action
Product InformationBasicity Index: 0.8Density: 1.5 g/cm3
700 Series Active FluxEN 760 – S A ZS 1
Key Features
FLUX COMPOSITION(1)
%SiO2 %MnO %MgO %CaF2 %Na2O %Al2O3 %ZrO2 %TiO2 %CaO % Metal Alloys
Lincolnweld® 781 21 17 14 5 2 4 21 12 1 3 max.
AWS TEST RESULTS(1)
Flux/Wire Combination
Weld Condition
Yield Strength(2)
Tensile Strength Elongation
(%)Charpy V-Notch
AWS Classification (A5.17/A5.23)MPa (ksi) MPa (ksi) J (ft•lbf) @ °C (°F)
L-50L-60L-61L-70
As-weldedAs-weldedAs-weldedAs-welded
530460530590
(77)(67)(77)(85)
610550610660
(89)(80)(89)(96)
29292825
38423135
(28)(31)(23)(26)
-18-18-18-18
(0)(0)(0)(0)
F7A0-EM13KF7A0-EL12
F7A0-EM12KF9A0-EA1-G
(1)See test results disclaimer on pg. 9. (2)Measured with 0.2% offset. NOTE: For the most up-to-date AWS certificates of conformances please visit www.lincolnelectric.com
Packaging
50lb(22.7kg)Bag ED019587
68281_233_288_ACG.indd 243 3/30/10 2:20 PM
[244] T H E L I N C O L N E L E C T R I C C O M P A N Y
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® 860submerged arc (saW) Flux
Recommended Wires
Typical Applications
For Mild Steel Lincolnweld® L-50, L-56, L-60, L-61, LA-71, L-S3For Low Alloy Steel Lincolnweld® L-70, LA-75, LA-82, LA-85
�AASHTO Fracture Critical applications with Lincolnweld® L-61 wire
�Pipe and other double ending applications
�General purpose structural and multiple pass welds
�Storage tanks using L-61 or LA-85
�May be used in as-welded or stress-relieved applications
� Industry standard for submerged arc welding applications
�Excellent operating characteristics in a variety of general welding applications
�Capable of producing weld deposits with impacttoughnessexceeding27J(20ft•lbf) at-40°C(-40°F)withLincolnweld® L-61
Product Information
Basicity Index: 1.1Density: 1.4g/cm3
800 Series Neutral FluxEN 760 – S A AB 1
Key Features
Packaging
50lb(22.7kg)Bag ED019589
68281_233_288_ACG.indd 244 3/30/10 2:20 PM
[245]W E L D I N G C O N S U M A B L E S C A T A L O G
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® 860submerged arc (saW) Flux
(EN 760 – S A AB 1)
(1)See test results disclaimer on pg. 9. (2)Measured with 0.2% offset. (3)Stress-relieved for 1 hour at 621°C (1150°F). NOTE: For the most up-to-date AWS certificates of conformances please visit www.lincolnelectric.com
AWS TEST RESULTS(1)
Flux/Wire Combination
Weld Condition
Yield Strength(2)
Tensile Strength Elongation
(%)Charpy V-Notch
AWS Classification (A5.17/A5.23)MPa (ksi) MPa (ksi) J (ft•lbf) @ °C (°F)
L-50L-56L-56L-60L-61L-61L-S3LA-71LA-71L-70L-70LA-75LA-75LA-82LA-85
As-weldedAs-welded
Stress-relieved(3)
As-weldedAs-welded
Stress-relieved(3)
As-weldedAs-welded
Stress relieved(3)
As-weldedStress-relieved(3)
As-weldedStress-relieved(3)
As-weldedAs-welded
430470440370410340500450400450430460410660520
(62)(68)(64)(54)(59)(49)(73)(65)(58)(65)(62)(66)(60)(96)(75)
520590570450500440590540520550520550540740600
(75)(86)(82)(65)(72)(64)(86)(78)(75)(80)(76)(80)(79)(107)(87)
302829343137283032283132302426
846180
13858
22252
1101195447
107995038
(62)(45)(59)(102)(43)(164)(38)(81)(88)(40)(35)(79)(73)(37)(28)
-29-29-29-29-40-46-29-29-29-29-29-29-29-40-40
(-20)(-20)(-20)(-20)(-40)(-50)(-20)(-20)(-20)(-20)(-20)(-20)(-20)(-40)(-40)
F7A2-EM13K-H8F7A2-EH11KF7P2-EH11K
F6A2-EL12-H8F7A4-EM12K-H8F6P5-EM12K-H8
F7A2-EH12KF7A2-EM14K-H8F7P2-EM14K-H8F7A2-EA1-A2-H8F7P2-EA1-A2-H8
F7A2-ENi1K-Ni1-H8F7P2-ENi1K-Ni1-H8F9A4-EF2-F2-H8E8A4-ENi5-Ni5-H8
FLUX COMPOSITION(1)
%SiO2 %MnO %MgO %CaF2 %Na2O %Al2O3 %CaO %TiO2 % Metal Alloys
Lincolnweld® 860 19 11 17 12 2 32 2 2 3 max.
68281_233_288_ACG.indd 245 3/30/10 2:20 PM
[246] T H E L I N C O L N E L E C T R I C C O M P A N Y
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® 865submerged arc (saW) Flux
Recommended Wires
Typical Applications
For Mild Steel Lincolnweld® L-50, L-61, LA-71For Low Alloy Steel Lincolnweld® LA-75
�Butt joints and flat and horizontal fillets
�Pair with Lincolnweld® L-61 on A516 steels
�General purpose flux designed to weld butt joints and flat and horizontal fillets
�When used with Lincolnweld® L-50 or L-61, itiscapableofproducing480MPa(70ksi)tensile strength after stress relief
�Small loss of strength when used in the stress-relieved condition Product Information
Basicity Index: 1.0Density: 1.3 g/cm3
800 Series Neutral FluxEN 760 – S A AR 1; EN 760 – S A AB 1
Key Features
FLUX COMPOSITION(1)
%SiO2 %MnO %MgO %CaF2 %Na2O %Al2O3 %TiO2 % Metal Alloys
Lincolnweld® 865 11 1 14 19 2 37 12 3 max.
AWS TEST RESULTS(1)
Flux/Wire Combination
Weld Condition
Yield Strength(2)
Tensile Strength Elongation
(%)Charpy V-Notch
AWS Classification (A5.17/A5.23)MPa (ksi) MPa (ksi) J (ft•lbf) @ °C (°F)
L-50L-50L-61L-61LA-71LA-75LA-75
As-weldedStress-relieved(3)
As-weldedStress-relieved(3)
As-weldedAs-welded
Stress-relieved(3)
500440480450540520500
(72)(64)(70)(65)(78)(76)(73)
580550570550630600610
(84)(80)(83)(80)(91)(87)(88)
27302230262327
532885
117737779
(39)(21)(63)(86)(54)(57)(58)
-29-46-29-29-29-29-29
(-20)(-50)(-20)(-20)(-20)(-20)(-20)
F7A2-EM13K-H8F7P5-EM13K-H8F7A2-EM12K-H8F7P2-EM12K-H8F7A2-EM14K-H8F8A2-ENi1K-G-H8F8P2-ENi1K-G-H8
(1)See test results disclaimer on pg. 9. (2)Measured with 0.2% offset. (3)Stress-relieved for 1 hour at 621°C (1150°F).NOTE: For the most up-to-date AWS certificates of conformances please visit www.lincolnelectric.com
Packaging
50lb(22.7kg)Bag EDS27857
68281_233_288_ACG.indd 246 3/30/10 2:20 PM
[247]W E L D I N G C O N S U M A B L E S C A T A L O G
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
submerged arc (saW) Flux
Lincolnweld ® 880
Recommended Wires
Typical Applications
For Low Alloy Steel Lincolnweld® LA-75, LA-90, LA-100, LAC-B2, LAC-M2, LAC-Ni2
�Applications requiring smooth bead appearance
�Hardfacing applications
�Can be used for both joining and hardfacing welding
�Optimal bead appearance when used with solid low alloy steel electrodes with a minimum of 0.20% silicon
�Use with both solid and flux cored wires Product Information
Basicity Index: 2.0Density: 1.4g/cm3
800 Series Neutral FluxEN 760 – S A AS 1; EN 760 – S A FB 1
Key Features
Packaging
50lb(22.7kg)Bag550lb(249.5kg)SteelDrum
ED027866 ED028322
FLUX COMPOSITION(1)
%SiO2 %MnO %CaF2 %Na2O %Al2O3 %CaO %ZrO2 % Metal Alloys
Lincolnweld® 880 17 27 27 2 16 2 7 5 max.
AWS TEST RESULTS(1)
Flux/Wire Combination
Weld Condition
Yield Strength(2)
Tensile Strength Elongation
(%)Charpy V-Notch
AWS Classification (A5.17/A5.23)MPa (ksi) MPa (ksi) J (ft•lbf) @ °C (°F)
LA-75LA-90LA-100LAC-B2LAC-M2LAC-Ni2LAC-Ni2
As-weldedAs-weldedAs-welded
Stress relieved(4)
As-weldedAs-welded
Stress relieved(3)
430540630480730460430
(62)(79)(92)(70)(106)(66)(63)
530640700590820540540
(77)(93)(101)(85)(119)(79)(78)
30282826182930
986153
13572140
95
(72)(45)(39)(100)(53)(103)(70)
-62-40-40-29-51-51-73
(-80)(-40)(-40)(-20)(-60)(-60) (-100)
F7A8-ENi1K-Ni1-H8F8A4-EA2K-A4-H8F9A4-EM2-M2-H8F8P2-ECB2-B2-H8
F11A6-ECM2-M2-H8F7A6-ECNi2-Ni2-H8F7P10-ECNi2-Ni2-H8
(1)See test results disclaimer on pg. 9. (2)Measured with 0.2% offset. (3)Stress-relieved for 1 hour at 621°C (1150°F). (4)Stress-relieved for 1 hour at 691°C (1275°F).NOTE: For the most up-to-date AWS certificates of conformances please visit www.lincolnelectric.com
68281_233_288_ACG.indd 247 3/30/10 2:20 PM
[248] T H E L I N C O L N E L E C T R I C C O M P A N Y
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® 880Msubmerged arc (saW) Flux
Recommended Wires
Typical Applications
For Mild Steel Lincolnweld® L-50, L-56, LA-71, L-S3For Low Alloy Steel Lincolnweld® LA-75, LA-85, LA-90, LA-92, LA-93, LA-100, LAC-B2, LAC-M2, LAC-Ni2
�Tandem arc applications for offshore fabrication
�Jobsrequiring480MPa(70ksi)tensilestrength after stress relief when used with L-56, L-S3, or LA-71
�A basic flux which features industry proven results in multiple pass applications
�Recommended for welding with solid mild steel and low alloy electrodes, as well as Lincoln’s LAC series of low alloy flux-cored electrodes
�Good deep groove slag removal
�Excellent choice for single arc AC submerged arc welding
Product Information
Basicity Index: 3.3Density: 1.2 g/cm3
800 Series Neutral FluxEN 760 – S A FB 1
Key Features
Packaging
50lb(22.7kg)PlasticBag ED031853
68281_233_288_ACG.indd 248 3/30/10 2:20 PM
[249]W E L D I N G C O N S U M A B L E S C A T A L O G
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® 880Msubmerged arc (saW) Flux
(EN 760 – S A FB 1)
FLUX COMPOSITION(1)
%SiO2 %MnO %MgO %CaF2 %Na2O %Al2O3 %CaO %K2O % Metal Alloys
Lincolnweld® 880M 12 1 29 29 1 18 8 1 1 max.
AWS TEST RESULTS(1)
Flux/Wire Combination
Weld Condition
Yield Strength(2)
Tensile Strength Elongation
(%)Charpy V-Notch
AWS Classification (A5.17/A5.23)MPa (ksi) MPa (ksi) J (ft•lbf) @ °C (°F)
L-50L-56L-56L-S3LA-71LA-71LA-75LA-85LA-85LA-90LA-90LA-92LA-93LA-100LAC-B2LAC-M2LAC-Ni2LAC-Ni2
As-weldedAs-welded
Stress-relieved(3)
As-weldedAs-welded
Stress-relieved(3)
As-weldedAs-welded
Stress-relieved(3)
As-weldedStress-relieved(3)
Stress-relieved(4)
Stress-relieved(4)
As-weldedStress-relieved(4)
As-weldedAs-welded
Stress-relieved(3)
410480400400480430440520490580520460510680500760510480
(59)(69)(58)(58)(70)(63)(64)(76)(71)(84)(75)(66)(74)(98)(72)(110)(73)(69)
510580540510570550550610590680630570610730600820600570
(74)(85)(78)(74)(82)(80)(80)(88)(85)(99)(91)(82)(88)(106)(87)(119)(87)(83)
323132322931312427262828262525232228
263121158264143164167
57145
68145178214129144
8377
103
(194)(89)(116)(195)(105)(121)(123)(42)(107)(50)(107)(131)(158)(95)(106)(61)(57)(76)
-62-51-51-51-62-62-62-51-62-51-62-29-18-51-29-51-73-73
(-80)(-60)(-60)(-60)(-80)(-80)(-80)(-60)(-80)(-60)(-80)(-20)(0)(-60)(-20)(-60)(-100)(-100)
F7A8-EM13K-H8F7A6-EH11K-H8F7P6-EH11K-H8F7A6-EH12K-H8F7A8-EM14K-H8F7P8-EM14K-H8
F7A8-ENi1K-Ni1-H8F7A6-ENi5-Ni5-H8F7P8-ENi5-Ni5-H8F9A6-EA3K-A3-H8F8P8-EA3K-A3-H8F7P2-EB2R-B2-H8F7P0-EB3R-B3-H8F9A6-EM2-M2-H8F8P2-ECB2-B2-H8
F11A6-ECM2-M2-H8F7A10-ECNi2-Ni2-H8F7P10-ECNi2-Ni2-H8
(1)See test results disclaimer on pg. 9. (2)Measured with 0.2% offset. (3)Stress-relieved for 1 hour at 621°C (1150°F). (4)Stress-relieved for 1 hour at 691°C (1275°F).NOTE: For the most up-to-date AWS certificates of conformances please visit www.lincolnelectric.com
68281_233_288_ACG.indd 249 3/30/10 2:20 PM
[250] T H E L I N C O L N E L E C T R I C C O M P A N Y
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® 882submerged arc (saW) Flux
Recommended Wires
Typical Applications
For Mild Steel Lincolnweld® L-50, L-56, L-60, L-61, LA-71, L-S3For Low Alloy Steel Lincolnweld® L-70, LA-75, LA-82, LA-85, LA-92, LA-93, LAC-Ni2
�Single wire or tandem welding
�Used for welding of stainless, mild and low alloy steel
�Excellent for multiple pass fillet welds
�Designed for a variety of welding applications and is known for providing consistent mechanical properties
�Recommended for stainless steel welding and can be paired with both mild and low alloy steel electrodes
�Smooth bead appearance
Product InformationBasicity Index: 1.6Density: 1.2 g/cm3
800 Series Neutral FluxEN 760 – S A AS 1; EN 760 – S A AS 2
Key Features
Packaging
50lb(22.7kg)Bag ED027859
68281_233_288_ACG.indd 250 3/30/10 2:20 PM
[251]W E L D I N G C O N S U M A B L E S C A T A L O G
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® 882submerged arc (saW) Flux
(EN 760 – S A AS 1; EN 760 – S A AS 2)
FLUX COMPOSITION(1)
%SiO2 %MnO %MgO %CaF2 %Na2O %Al2O3 %CaO %ZrO2 % Metal Alloys
Lincolnweld® 882 16 1 22 24 2 24 1 7 3 max.
AWS TEST RESULTS(1)
Flux/Wire Combination
Weld Condition
Yield Strength(2)
Tensile Strength Elongation
(%)Charpy V-Notch
AWS Classification (A5.17/A5.23)MPa (ksi) MPa (ksi) J (ft•lbf) @ °C (°F)
L-50L-56L-56L-60L-61L-S3L-S3LA-71LA-71L-70LA-75LA-82LA-85LA-85LA-92LA-93LAC-Ni2LAC-Ni2
As-weldedAs-welded
Stress-relieved(3)
As-weldedAs-weldedAs-welded
Stress-relieved(3)
As-weldedStress-relieved(3)
Stress-relieved(3)
As-weldedAs-weldedAs-welded
Stress-relieved(3)
Stress-relieved(4)
Stress-relieved(4)
As-weldedStress-relieved(3)
420500420370400410410480430450430660510500520610570500
(61)(73)(61)(54)(58)(60)(59)(69)(62)(65)(62)(95)(74)(73)(75)(88)(83)(73)
520600560460500520510570550550540740610590610700660600
(76)(87)(81)(67)(72)(76)(78)(82)(80)(80)(79)(108)(88)(86)(89)(101)(95)(87)
292830323128323132303226252627232025
1309247
207190130115
617076
1335688
10283214
72100
(96)(68)(35)(153)(140)(96)(85)(45)(52)(56)(98)(41)(65)(75)(61)(158)(53)(74)
-51-40-46-51-51-51-62-51-51-40-40-51-40-40-29-18-40-40
(-60)(-40)(-50)(-60)(-60)(-60)(-80)(-60)(-60)(-40)(-40)(-60)(-40)(-40)(-20)(0)(-40)(-40)
F7A6-EM13K-H8F7A4-EH11K-H8F7P5-EH11K-H8F6A6-EL12-H8
F7A6-EM12K-H8F7A6-EH12K-H8F7P8-EH12K-H8F7A6-EM14K-H8F7P6-EM14K-H8F7P4-EA1-A2-H8F7A4-ENi1K-Ni1-H8F10A6-EF2-F2-H8F7A4-ENi5-Ni5-H8F7P4-ENi5-Ni5-H8F7P2-EB2R-B2-H8F9P0-EB3R-B3-H8F8A4-ECNi2-Ni2-H8F7P4-ECNi2-Ni2-H8
(1)See test results disclaimer on pg. 9. (2)Measured with 0.2% offset. (3)Stress-relieved for 1 hour at 621°C (1150°F). (4)Stress-relieved for 1 hour at 691°C (1275°F).NOTE: For the most up-to-date AWS certificates of conformances please visit www.lincolnelectric.com
68281_233_288_ACG.indd 251 3/30/10 2:20 PM
[252] T H E L I N C O L N E L E C T R I C C O M P A N Y
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® 888submerged arc (saW) Flux
Recommended Wires
Typical Applications
For Mild Steel Lincolnweld® L-50, L-56, L-S3, L-61, LA-71For Low Alloy Steel Lincolnweld®L-70,LA-75,LA-82,LA-84, LA-85, LA-90, LA-100, LAC-Ni2, LAC-M2, LAC-B2
�Excellent operation with multiple arcs
�Offshore
�Structural fabrication
�Shipbuilding
�Designed for deep groove slag removal in critical applications
�Recommended for joining mild steel and low alloy steels in as-welded and stress-relieved applications
�LowH4diffusiblehydrogenlevels
�Moisture resistant packaging
�Charpy V-Notch and CTOD test results available for most alloy systems Product Information
Basicity Index: 2.2Density: 1.3 g/cm3
800 Series Neutral FluxEN 760 – S A FB 1
Key Features
Packaging
50lb(22.7kg)PlasticBag ED031596
68281_233_288_ACG.indd 252 3/30/10 2:20 PM
[253]W E L D I N G C O N S U M A B L E S C A T A L O G
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® 888Submerged Arc (SAW) Flux
(EN 760 – S A FB 1)
FLUX COMPOSITION(1)
%SiO2 %MnO %MgO %CaF2 %Na2O %Al2O3 %CaO %FeO %K2O % Metal Alloys
Lincolnweld® 888 18 1 27 25 2 19 5 1 2 3 max.
AWS TEST RESULTS(1)
Flux/Wire Combination
Weld Condition
Yield Strength(2)
Tensile Strength Elongation
(%)Charpy V-Notch
AWS Classification (A5.17/A5.23)MPa (ksi) MPa (ksi) J (ft•lbf) @ °C (°F)
L-50L-50L-56L-56L-61L-S3L-S3LA-71LA-71L-70L-70LA-75LA-82LA-82LA-84LA-84LA-85LA-85LA-90LA-100LAC-B2LAC-M2LAC-Ni2LAC-Ni2
As-weldedStress-relieved(3)
As-weldedStress-relieved(3)
As-weldedAs-welded
Stress-relieved(3)
As-weldedStress-relieved(3)
As-weldedStress-relieved(3)
As-weldedAs-welded
Stress-relieved(3)
As-weldedStress-relieved(3)
As-weldedStress-relieved(3)
As-weldedAs-welded
Stress-relieved(4)
As-weldedAs-welded
Stress-relieved(3)
430370510410420480370520410510470470690600630580540500610690520860540480
(62)(53)(74)(59)(61)(70)(54)(75)(60)(74)(69)(68)(99)(87)(92)(84)(78)(72)(89)(100)(76)(124)(78)(70)
540510610540520570510610540600570580780700720670640590700760620930630580
(78)(74)(88)(79)(75)(83)(74)(89)(78)(87)(83)(84)(113)(102)(105)(98)(92)(86)(102)(111)(90)(135)(92)(84)
313229323133332832293131232523262627262524152027
122187
71118121
70165
68134
60126122
707977347976566182635664
(90)(138)(52)(87)(89)(52)(122)(50)(99)(45)(93)(90)(52)(58)(57)(25)(58)(56)(41)(45)(60)(46)(42)(47)
-62-62-51-62-51-62-62-51-62-40-40-62-62-51-62-51-51-51-51-40-40-62-62-73
(-80)(-80)(-60)(-80)(-60)(-80)(-80)(-60)(-80)(-40)(-40)(-80)(-80)(-60)(-80)(-60)(-60)(-60)(-60)(-40)(-40)(-80)(-80)(-100)
F7A8-EM13K-H4F6P8-EM13K-H4F8A6-EH11K-H4F7P8-EH11K-H4F7A6-EM12K-H4F7A8-EH12K-H4F6P8-EH12K-H4F7A6-EM14K-H4F7P8-EM14K-H4F7A4-EA1-A2-H4F7P4-EA1-A2-H4
F7A8-ENi1K-Ni1-H4F10A8-EF2-F2-H4F9P6-EF2-F2-H4F9A8-EF3-F3-H4F8P6-EF3-F3-H4
F8A6-ENi5-Ni5-H4F7P6-ENi5-Ni5-H4F9A6-EA3K-A3-H4F10A4-EM2-M2-H4F8P4-ECB2-B2-H8F12A8-ECG-G-H8
F8A8-ECNi2-Ni2-H8F7P10-ECNi2-Ni2-H8
(1)See test results disclaimer on pg. 9. (2)Measured with 0.2% offset. (3)Stress-relieved for 1 hour at 621°C (1150°F). (4)Stress-relieved for 1 hour at 691°C (1275°F).NOTE: For the most up-to-date AWS certificates of conformances please visit www.lincolnelectric.com
68281_233_288_ACG.indd 253 4/6/10 9:32 AM
[254] T H E L I N C O L N E L E C T R I C C O M P A N Y
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® 8500submerged arc (saW) Flux
Recommended Wires
Typical Applications
For Mild Steel Lincolnweld® L-50, L-56, L-61, L-S3, LA-71For Low Alloy Steel Lincolnweld® LA-82, LA-85, LA-90, LA-92
�Fabrication of offshore drilling platforms
�Multiple pass welding
�Single and multiple arc welding
�Capable of providing impact properties necessary for thick weld joints from root to cap pass
�Operates well on AC and multiple arcs with good resistance to nitrogen porosity
�Capable of producing weld deposits with impactpropertiesexceeding27J(20ft•lbf) at-62°C(-80°F)
�CTOD data available for this flux with many alloy systems
Product Information
Basicity Index: 2.9Density: 1.3 g/cm3
800 Series Neutral FluxEN 760 - S A FB 1
Key Features
Packaging
50lb(22.7kg)PlasticBag ED031854
Note �This product contains micro-alloying elements. Additional information available upon request.
68281_233_288_ACG.indd 254 3/30/10 2:20 PM
[255]W E L D I N G C O N S U M A B L E S C A T A L O G
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® 8500submerged arc (saW) Flux
(EN 760 - S A FB 1)
AWS TEST RESULTS(1)
Flux/Wire Combination
Weld Condition
Yield Strength(2)
Tensile Strength Elongation
(%)Charpy V-Notch
AWS Classification (A5.17/A5.23)MPa (ksi) MPa (ksi) J (ft•lbf) @ °C (°F)
L-50L-56L-56L-61L-S3LA-71LA-71LA-82LA-82LA-85LA-85LA-90LA-92
As-weldedAs-welded
Stress-relieved(3)
As-weldedAs-weldedAs-welded
Stress-relieved(3)
As-weldedStress-relieved(3)
As-weldedStress-relieved(3)
As-weldedStress-relieved(4)
430470430400460450420660610510500670550
(63)(68)(62)(58)(67)(66)(61)(95)(89)(74)(72)(97)(80)
520570540480570550520740700590590590640
(76)(82)(79)(70)(82)(80)(75)(108)(102)(86)(85)(85)(93)
32313331293032222429282426
129132151168
91155220
8783
15513484
209
(95)(97)(111)(124)(67)(115)(162)(64)(61)(114)(99)(62)(154)
-62-62-62-51-62-62-62-51-51-62-51-29-18
(-80)(-80)(-80)(-60)(-80)(-80)(-80)(-60)(-60)(-80)(-60)(-20)(0)
F7A8-EM13K-H8F7A8-EH11KF7P8-EH11K
F7A6-EM12K-H8F7A8-EH12K-H8F7A8-EM14K-H8F7P8-EM14K-H8F9A6-EF2-F2-H8F9P6-EF2-F2-H8
F8A8-ENi5-Ni5-H8F7P6-ENi5-Ni5-H8F9A2-EA3K-A3-H8F8P0-EB2-B2-H8
(1)See test results disclaimer on pg. 9. (2)Measured with 0.2% offset. (3)Stress-relieved for 1 hour at 621°C (1150°F). (4)Stress-relieved for 1 hour at 691°C (1275°F).NOTE: For the most up-to-date AWS certificates of conformances please visit www.lincolnelectric.com
FLUX COMPOSITION(1)
%SiO2 %MnO %MgO %CaF2 %Na2O %Al2O3 %CaO %K2O %TiO2 % Metal Alloys
Lincolnweld® 8500 13 1 30 24 2 19 8 1 1 1 max.
68281_233_288_ACG.indd 255 3/30/10 2:20 PM
[256] T H E L I N C O L N E L E C T R I C C O M P A N Y
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® MIL800-Hsubmerged arc (saW) Flux
Recommended Wires
Typical Applications
For Mild Steel Lincolnweld® L-S3, LA-71For Low Alloy Steel Lincolnweld® LA-75, LA-82, LA-85, LA-90, LA-93, LA-100
�HY-80 and HSLA-80 steels with Lincolnweld® LA-100 wire
�Horizontal and flat fillet welds
�Single and multiple arc welding
�High strength or highly restrained weldments where delayed cracking is a concern
�Capable of providing industry leading H2 diffusible hydrogen levels
�Designed for low temperature applications
�Recommended for both single and multiple arc welding of both butt and fillet welds
Product InformationBasicity Index: 3.2Density: 1.3 g/cm3
800 Series Neutral FluxEN 760 - S A CS 1; EN 760 - S A FB 1
Key Features
Packaging
50lb(22.7kg) Hermetically Sealed Pail ED020925
68281_233_288_ACG.indd 256 3/30/10 2:20 PM
[257]W E L D I N G C O N S U M A B L E S C A T A L O G
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® MIL800-Hsubmerged arc (saW) Flux
(EN 760 - S A CS 1; EN 760 - S A FB 1)
AWS TEST RESULTS(1)
Flux/Wire Combination
Weld Condition
Yield Strength(2)
Tensile Strength Elongation
(%)Charpy V-Notch
AWS Classification (A5.17/A5.23)MPa (ksi) MPa (ksi) J (ft•lbf) @ °C (°F)
L-S3L-S3LA-71LA-71LA-75LA-82LA-82LA-85LA-85LA-90LA-90LA-93LA-100
As-weldedStress-relieved(3)
As-weldedStress-relieved(3)
As-weldedAs-welded
Stress-relieved(3)
As-weldedStress-relieved(3)
As-weldedStress-relieved(3)
Stress-relieved(4)
As-welded
500570570540560800740660630710690690780
(73)(64)(68)(61)(67)(102)(95)(82)(78)(90)(86)(84)(97)
610570570540560800740660630710690690780
(88)(82)(82)(79)(82)(116)(108)(95)(92)(103)(100)(99)(112)
27303032302125252626262325
76118163193156
9176
10883778434
107
(56)(87)(120)(140)(115)(67)(56)(80)(61)(57)(62)(25)(79)
-62-62-51-51-62-51-51-62-62-51-51-29-51
(-80)(-80)(-60)(-60)(-80)(-60)(-60)(-80)(-80)(-60)(-60)(-20)(-60)
F7A8-EH12K-H2F7P8-EH12K-H2F7A6-EM14K-H2F7P6-EM14K-H2
F7A8-ENi1K-Ni1-H2F10A6-EF2-F2-H2F10P6-EF2-F2-H2F8A8-ENi5-Ni5-H2F8P8-ENi5-Ni5-H2F9A6-EA3K-A3-H2F9P6-EA3K-A3-H2F9P2-EB3R-B3-H2F10A6-EM2-M2-H2
(1)See test results disclaimer on pg. 9. (2)Measured with 0.2% offset. (3)Stress-relieved for 1 hour at 621°C (1150°F). (4)Stress-relieved for 1 hour at 691°C (1275°F).NOTE: For the most up-to-date AWS certificates of conformances please visit www.lincolnelectric.com
FLUX COMPOSITION(1)
%SiO2 %MnO %MgO %CaF2 %Na2O %Al2O3 %CaO %K2O % Metal Alloys
Lincolnweld® MIL800-H 13 1 34 23 1 16 8 1 1 max.
68281_233_288_ACG.indd 257 3/30/10 2:20 PM
[258] T H E L I N C O L N E L E C T R I C C O M P A N Y
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® 960submerged arc (saW) Flux
Recommended Wires
Typical Applications
For Mild Steel Lincolnweld® L-50, L-61, LA-71For Low Alloy Steel Lincolnweld® LA-75, LA-85, LA-93, LA-100
�Single and multiple pass welding
�Fillet and butt welds with unlimited plate thickness
�Can weld steel with heavy scale or rust when used with Lincolnweld® L-50 wire
�Weathering steels when used with Lincolnweld® LA-75 wire
�Low cost, general purpose flux designed to weld butt joints and both single and multiple pass fillets
�Recommended for automatic and semiautomatic submerged arc welding
�A versatile, cost-effective flux that can be used with many alloy systems
�Can be used on A588 weathering steels when combined with Lincolnweld® LA-75
Product InformationBasicity Index: 1.1Density: 1.4g/cm3
Special Neutral FluxEN 760 - S A AB 1
Key Features
Packaging
50lb(22.7kg)Bag ED022412
AWS D1.8 and FEMA 353Approved when paired with the following wires:• 1/8in(3.2mm)Lincolnweld® L-61• 1/8in(3.2mm)Lincolnweld®LA-84• 1/8in(3.2mm)Lincolnweld® LA-85
Structural Welding Code Seismic Supplement
68281_233_288_ACG.indd 258 3/30/10 2:20 PM
[259]W E L D I N G C O N S U M A B L E S C A T A L O G
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® 960submerged arc (saW) Flux
(EN 760 - S A AB 1)
AWS TEST RESULTS(1)
Flux/Wire Combination
Weld Condition
Yield Strength(2)
Tensile Strength Elongation
(%)Charpy V-Notch
AWS Classification (A5.17/A5.23)MPa (ksi) MPa (ksi) J (ft•lbf) @ °C (°F)
L-50L-61LA-71LA-71LA-75LA-75LA-85LA-85LA-93LA-100
As-weldedAs-weldedAs-welded
Stress-relieved(3)
As-weldedStress-relieved(3)
As-weldedStress-relieved(3)
Stress-relieved(4)
As-welded
460420460420480420520500580680
(66)(61)(66)(61)(69)(61)(76)(73)(84)(99)
570520570540600550640610680740
(83)(75)(82)(79)(87)(80)(93)(88)(98)(108)
27322931302924252225
581254489765357396533
(43)(92)(32)(66)(56)(39)(42)(29)(48)(24)
-29-29-29-29-29-51-29-46-18-40
(-20)(-20)(-20)(-20)(-20)(-60)(-20)(-50)(0)(-40)
F7A2-EM13K-H8F7A2-EM12K-H8F7A2-EM14K-H8F7P2-EM14K-H8
F8A2-ENi1K-Ni1-H8F7P6-ENi1K-Ni1-H8
F8A2-ENi5-G-H8F7P5-ENi5-G-H8F9P0-EB3R-G-H8F10A4-EM2-G-H8
(1)See test results disclaimer on pg. 9. (2)Measured with 0.2% offset. (3)Stress-relieved for 1 hour at 621°C (1150°F). (4)Stress-relieved for 1 hour at 691°C (1275°F).NOTE: For the most up-to-date AWS certificates of conformances please visit www.lincolnelectric.com
FLUX COMPOSITION(1)
%SiO2 %MnO %MgO %CaF2 %Na2O %Al2O3 %CaO %TiO2 % Metal Alloys
Lincolnweld® 960 21 10 21 10 2 31 1 1 3 max.
68281_233_288_ACG.indd 259 3/30/10 2:20 PM
[260] T H E L I N C O L N E L E C T R I C C O M P A N Y
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® 980submerged arc (saW) Flux
Recommended Wires
Typical Applications
For Mild Steel Lincolnweld® L-50, L-61, LC-72For Low Alloy Steel Lincolnweld® LA-75, LAC-Ni2
�Semiautomatic, single and multiple pass submerged arc welding
�General purpose fabrication
�Fillet welds
�Combines many of the features of the 700 and 800 series fluxes and is ideal for semiautomatic submerged arc welding
�Exceptional resistance to flash-through and porosity caused by arc blow in a variety of applications
�Especially high productivity when used with Lincolnweld® LC-72 wire
Product Information
Basicity Index: 0.6Density: 1.4g/cm3
Special Neutral FluxEN 760 - S A AB 1; EN 760 - S A AR 1
Key Features
Packaging
50lb(22.7kg)Bag ED027861
AWS TEST RESULTS(1)
Flux/Wire Combination
Weld Condition
Yield Strength(2)
Tensile Strength Elongation
(%)Charpy V-Notch
AWS Classification (A5.17/A5.23)MPa (ksi) MPa (ksi) J (ft•lbf) @ °C (°F)
L-50L-61LC-72LA-75LAC-Ni2
As-weldedAs-weldedAs-weldedAs-weldedAs-welded
430430450510540
(63)(63)(65)(74)(79)
540530540600630
(78)(77)(78)(87)(91)
3131282825
43374361
110
(32)(27)(32)(45)(81)
-29-29-29-29-29
(-20)(-20)(-20)(-20)(-20)
F7A2-EM13K-H8F7A2-EM12K-H8
F7A2-EC1-H8F7A2-ENi1K-Ni1-H8F8A2-ECNi2-Ni2-H8
(1)See test results disclaimer on pg. 9. (2)Measured with 0.2% offset. NOTE: For the most up-to-date AWS certificates of conformances please visit www.lincolnelectric.com
FLUX COMPOSITION(1)
%SiO2 %MnO %MgO %CaF2 %Na2O %Al2O3 %TiO2 % Metal Alloys
Lincolnweld® 980 11 14 2 12 2 47 7 4max.
68281_233_288_ACG.indd 260 3/30/10 2:20 PM
[261]W E L D I N G C O N S U M A B L E S C A T A L O G
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
submerged arc (saW) Flux
Lincolnweld ® WTX
Recommended Wires
Typical Applications
For Mild Steel Lincolnweld® L-61For Low Alloy Steel Lincolnweld® L-70
�Wind tower base
�Wind tower door frame
�Neutral submerged arc welding flux designed to meet the specific requirements of wind tower welding applications
�Recommended for use with Lincolnweld® L-61 electrode on both longitudinal and circumferential seam welds
�Capable of producing weld deposits with impactpropertiesexceeding27J(20ft•lbf) at-62°C(-80°F)
�Smooth bead profile to achieve excellent toe angles, tie-in, and bead appearance on interior and exterior applications
Product Information
BasicityIndex: 1.4Density: 1.2 g/cm3
Special Neutral FluxEN 760 SA AB 1
Key Features
Packaging
50lb(22.7kg)PlasticBag ED032990
AWS TEST RESULTS(1)
Flux/Wire Combination
Weld Condition
Yield Strength(2)
Tensile Strength Elongation
(%)Charpy V-Notch
AWS Classification (A5.17/A5.23)MPa (ksi) MPa (ksi) J (ft•lbf) @ °C (°F)
L-61L-70
As-weldedAs-welded
430500
(63)(73)
540610
(78)(88)
3125
8446(62)(34)
-62-40
(-80)(-40)
F7A8-EM12K-H8F8A4-EA1-A3-H8
(1)See test results disclaimer on pg. 9. (2)Measured with 0.2% offset. NOTE: For the most up-to-date AWS certificates of conformances please visit www.lincolnelectric.com
FLUX COMPOSITION(1)
%SiO2 %MnxOy %MgO %CaF2 %NaO %Al2O3 %CaO %ZrO2 %FeO %K2O %TiO2
Lincolnweld® WTX 21 9 23 13 2 25 5 1 2 1 1
68281_233_288_ACG.indd 261 3/30/10 2:20 PM
[262] T H E L I N C O L N E L E C T R I C C O M P A N Y
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® 761-Pipesubmerged arc (saW) Flux
Recommended Wires
Typical Applications
For Mild Steel Lincolnweld® L-61For Low Alloy Steel Lincolnweld® L-70
�Single and multiple arc welding
�Longitudinal seam welding of API grade pipe
�Spiral seam welding of API grade or water pipe
�Features the chemical composition of 761 with a particle size optimized for seam welding
�Low-melting slag system produces wide flat welds with superior resistance to cracks and pockmarking
�Can handle up to 5 arcs or 5,000 amps Product Information
Basicity Index: 0.8Density: 1.2 g/cm3
Flux for Seam Welding of PipeEN 760 S A MS 1; EN 760 S A CS 1
Key Features
Packaging
50lb(22.7kg)PlasticBag ED032797
AWS TEST RESULTS(1)
Flux/Wire Combination
Weld Condition
Yield Strength(2)
Tensile Strength Elongation
(%)Charpy V-Notch
AWS Classification (A5.17/A5.23)MPa (ksi) MPa (ksi) J (ft•lbf) @ °C (°F)
L-61L-70
As-weldedAs-welded
490550
(70)(80)
580640
(85)(93)
2824
5458(40)(43)
-29-18
(-20)(0)
F7A2-EM12K-H8F9A0-EA1-G
(1)See test results disclaimer on pg. 9. (2)Measured with 0.2% offset. NOTE: For the most up-to-date AWS certificates of conformances please visit www.lincolnelectric.com
FLUX COMPOSITION(1)
%SiO2 %MnxOy %MgO %CaF2 %NaO %Al2O3 %TiO2 %FeO % Metal Alloys
Lincolnweld® 761-Pipe 45 19 22 5 2 2 2 1 6 max.
68281_233_288_ACG.indd 262 3/30/10 2:20 PM
[263]W E L D I N G C O N S U M A B L E S C A T A L O G
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
submerged arc (saW) Flux
Lincolnweld ® P223
Recommended Wires
Typical Applications
For Mild Steel Lincolnweld® L-56, L-61, LA-71, L-S3For Low Alloy Steel Lincolnweld® L-70, LA-90
�Pipe welding up to X80 grade pipe
�Two run welding applications for pipe fabrication
�Multiple pass welding for general construction
� Industry standard for pipe welding on up to X80 grade pipe
�Fast freezing and easily removable slag for excellent bead profile
�Can be used for welding with up to three arcsProduct Information
Basicity Index: 1.5Density: 1.2 g/cm3
Flux for Seam Welding of Pipe EN 760 - S A AB 1
Key Features
Packaging
50lb(22.7kg)PlasticBag2600lb(1179kg)BulkBag
ED032764ED032767
AWS TEST RESULTS(1)
Flux/Wire Combination
Weld Condition
Yield Strength(2)
Tensile Strength Elongation
(%)Charpy V-Notch
AWS Classification (A5.17/A5.23)MPa (ksi) MPa (ksi) J (ft•lbf) @ °C (°F)
L-56L-56L-61LA-71LA-71L-S3L-S3L-70LA-90
As-weldedStress-relieved(3)
As-weldedAs-welded
Stress-relieved(3)
As-weldedStress-relieved(3)
As-weldedAs-welded
500540430480410460410550630
(73)(65)(63)(69)(60)(67)(60)(80)(91)
620580530570540570540650720
(90)(84)(77)(83)(78)(82)(78)(94)(105)
303031293230322525
6866
126947688
1035360
(50)(49)(93)(69)(56)(65)(76)(39)(44)
-51-51-40-40-51-62-62-29-18
(-60)(-60)(-40)(-40)(-60)(-80)(-80)(-20)(0)
F7A6-EH11K-H8F7P6-EH11K-H8F7A4-EM12KF7A4-EM14K-H8F7P6-EM14K-H8F7A8-EH12K-H8F7P8-EH12K-H8
F8A2-EA1-A2F9A0-EA3K-G
(1)See test results disclaimer on pg. 9. (2)Measured with 0.2% offset. (3)Stress-relieved for 1 hour at 621°C (1150°F).NOTE: For the most up-to-date AWS certificates of conformances please visit www.lincolnelectric.com
FLUX COMPOSITION(1)
%SiO2 %MnO %MgO %CaF2 %NaO %Al2O3 %CaO %TiO2 %K2O %FeO % Metal Alloys
Lincolnweld® P223 23 4 21 21 2 20 4 2 1 1 3 max.
68281_233_288_ACG.indd 263 3/30/10 2:20 PM
[264] T H E L I N C O L N E L E C T R I C C O M P A N Y
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® SPX80submerged arc (saW) Flux
Recommended Wires
Typical Applications
For Mild Steel Lincolnweld® L-61
For Low Alloy Steel Lincolnweld® L-70, LA-81, LA-90
�Spiral pipe mills
�Two run welding applications
�Weld up to API X80 pipe
�Designed to meet the specific requirements of spiral pipe seam welding of up to API X80 grade pipe
�High speed welding capability for increased productivity
�Capable of producing weld deposits with impactpropertiesexceeding27J(20ft•lbf) at-51°C(-60°F)withLincolnweld® LA-81
� Smooth bead profile achieves optimal appearance on both inner and outer diameter welds
� Self-peeling slag allows for clean and easy slag removal for reliable non-destructive testing results
Product Information
Basicity Index: 1.3Density: 1.2 g/cm3
Flux for Seam Welding of PipeEN 760 SA AB 1
Key Features
Packaging
50lb(22.7kg)PlasticBag ED032960
68281_233_288_ACG.indd 264 3/30/10 2:20 PM
[265]W E L D I N G C O N S U M A B L E S C A T A L O G
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® SPX80submerged arc (saW) Flux
(EN 760 SA AB 1)
AWS TEST RESULTS(1) - MULTI-PASS
Flux/Wire Combination
Weld Condition
Yield Strength(2)
Tensile Strength Elongation
(%)Charpy V-Notch
AWS Classification (A5.17/A5.23)MPa (ksi) MPa (ksi) J (ft•lbf) @ °C (°F)
L-61L-70LA-90
As-WeldedAs-WeldedAs-Welded
430530610
(62)(77)(89)
543620720
(79)(89)(105)
312525
946839
(69)(50)(29)
-46-40-40
(-50)(-40)(-40)
F7A5-EM12K-H8F8A4-EA1-A4-H8F8A4-EA1-A4-H8
FLUX COMPOSITION(1)
%SiO2 %MnO %MgO %CaF2 %NaO %Al2O3 %CaO %ZrO2 %FeO %TiO2
Lincolnweld® SPX80 23 9 21 14 2 25 2 2 1 1
AWS TEST RESULTS(1) - TWO RUN
Flux/Wire Combination
SteelType
Weld Condition
Yield Strength(2)
Tensile Strength Elongation
(%)Charpy V-Notch
AWS Classification (A5.17/A5.23)MPa (ksi) MPa (ksi) J (ft•lbf) @ °C (°F)
L-61L-70L-70LA-81LA-81LA-90LA-90LA-90
A131A131X65X65X80X65X70X80
As-weldedAs-weldedAs-weldedAs-weldedAs-weldedAs-weldedAs-weldedAs-welded
460500560580630590580630
(67)(72)(82)(84)(92)(86)(85)(93)
600620650680690690700690
(87)(89)(94)(98)(101)(101)(102)(100)
3027262526242727
4538884311437
11372
(33)(28)(65)(32)(84)(27)(83)(53)
-18-40-40-40-51-51-40-40
(0)(-40)(-40)(-40)(-60)(-60)(-40)(-40)
F7TA0-EM12KF7TA4-EA1F8TA4G-EA1F9TA4G-EGF9TA6G-EG
F9TA6G-EA3KF9TA4G-EA3KF9TA4G-EA3K
(1)See test results disclaimer on pg. 9. (2)Measured with 0.2% offset. NOTE: For the most up-to-date AWS certificates of conformances please visit www.lincolnelectric.com
68281_233_288_ACG.indd 265 3/30/10 2:20 PM
[266] T H E L I N C O L N E L E C T R I C C O M P A N Y
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® 995Nsubmerged arc (saW) Flux
Recommended Wires
Typical Applications
For Mild Steel Lincolnweld® L-61For Low Alloy Steel Lincolnweld® L-70, LA-81, LA-90
�Automatic, single pass welding
�Single or multiple arc welding
�High speed longitudinal seam welding on a range of pipe steels
�One side welding requiring impact properties
�A nitrogen limiting flux designed for seam welding of pipe
�Recommended for automatic single pass welding with up to five arcs
�Produces welds with minimal buildup and good penetration
�Capable of producing Charpy V-Notch test results required for arctic grade service
Product Information
Basicity Index: 1.3Density: 1.0 g/cm3
Flux for Seam Welding of PipeEN 760 - S A AB 1
Key Features
Packaging
50lb(22.7kg)PlasticBag ED032831
AWS TEST RESULTS(1)
Flux/Wire Combination
Weld Condition
Yield Strength(2)
Tensile Strength Elongation
(%)Charpy V-Notch
AWS Classification (A5.17/A5.23)MPa (ksi) MPa (ksi) J (ft•lbf) @ °C (°F)
L-61L-70LA-81LA-90
As-weldedAs-weldedAs-weldedAs-welded
430510590600
(63)(74)(96)(87)
540610660700
(79)(88)(96)(102)
29242625
83735854
(61)(54)(43)(40)
-40-29-29-29
(-40)(-20)(-20)(-20)
F7A4-EM12K-H8F8A2-EA1-A4F9A2-EG-G
F9A2-EA3K-G
FLUX COMPOSITION(1)
%SiO2 %MnO %MgO %CaF2 %Na2O %Al2O3 %CaO %ZrO2 %FeO %TiO2 % Metal Alloys
Lincolnweld® 995N 19 11 16 14 3 27 5 2 1 1 3 max.
(1)See test results disclaimer on pg. 9. (2)Measured with 0.2% offset. NOTE: For the most up-to-date AWS certificates of conformances please visit www.lincolnelectric.com
68281_233_288_ACG.indd 266 3/30/10 2:20 PM
[267]W E L D I N G C O N S U M A B L E S C A T A L O G
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
submerged arc (saW) Flux
Lincolnweld ® AXXX-10
Recommended Wires
Typical Applications
For Low Alloy Lincolnweld® L-61
�Welding of A588 weathering steels and ASTM A533-Class 1
�An alloy flux designed to produce a 1% nickel-bearing weld deposit
�Recommended for use on ASTM A533 Class 1 and A588 weathering steels when combined with Lincolnweld® L-61
Product Information
Basicity Index: 1.0Density: 1.4g/cm3
High Performance / Alloy Flux
Key Features
Packaging
50lb(22.7kg)Bag ED027862
AWS TEST RESULTS(1)
Flux/Wire Combination
Weld Condition
Yield Strength(2)
Tensile Strength Elongation
(%)Charpy V-Notch
AWS Classification (A5.17/A5.23)MPa (ksi) MPa (ksi) J (ft•lbf) @ °C (°F)
L-61 As-welded 460 (67) 570 (83) 30 85 (63) -40 (-40) F7A4-EM12K-Ni1-H8
FLUX COMPOSITION(1)
%SiO2 %MnO %MgO %CaF2 %Na2O %Al2O3 %ZrO2 %TiO2 % Metal Alloys
Lincolnweld® AXXX-10 18 5 22 11 2 19 22 1 5 max.
(1)See test results disclaimer on pg. 9. (2)Measured with 0.2% offset. NOTE: For the most up-to-date AWS certificates of conformances please visit www.lincolnelectric.com
Notes
�Since the alloy level in the weld deposit depends upon the arc voltage, and thus the arc length, always maintain a consistent arc voltage. If more flexibility in procedure is necessary, use 960 flux and LA-75 electrode.
68281_233_288_ACG.indd 267 3/30/10 2:20 PM
[268] T H E L I N C O L N E L E C T R I C C O M P A N Y
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® MIL800-HPNisubmerged arc (saW) Flux
Recommended Wires
Typical Applications
For Low Alloy Steel Lincolnweld® LA-75, LA-85, LA-100
�Bridge fabrication with HPS70W steel, when used with LA-85 wire
�Single or multiple wire arc welding
�Butt and fillet welds on low alloy steels
�When used with Lincolnweld® LA-85 the nickel content will increase from a nominal 1% to a minimum 1%
�Use on high performance steel applications, including HPS70W or HPS100W
�Capable of producing ultra low H2 diffusible hydrogen levels on HPS steels
Product Information
Basicity Index: 3.1Density: 1.3 g/cm3
High Performance / Alloy FluxEN 760 - S A CS 1; EN 760 - S A FB 1
Key Features
Packaging
50lb(22.7kg) Hermetically Sealed Pail ED028657
AWS TEST RESULTS(1)
Flux/Wire Combination
Weld Condition
Yield Strength(2)
Tensile Strength Elongation
(%)Charpy V-Notch
AWS Classification (A5.17/A5.23)MPa (ksi) MPa (ksi) J (ft•lbf) @ °C (°F)
LA-75LA-85LA-100
As-weldedAs-weldedAs-welded
560600800
(81)(88)(116)
640690850
(93)(100)(123)
282523
145143
91
(107)(105)(67)
-51-40-40
(-60)(-40)(-40)
F8A6-ENi1K-G-H2F9A4-ENi5-G-H2F11A4-EM2-G-H2
FLUX COMPOSITION(1)
%SiO2 %MgO %CaF2 %Na2O %Al2O3 %CaO %TiO2 %K2O %FeO % Metal Alloys
Lincolnweld® MIL800-HPNi 13 34 22 1 16 8 2 1 1 3 max.
(1)See test results disclaimer on pg. 9. (2)Measured with 0.2% offset. NOTE: For the most up-to-date AWS certificates of conformances please visit www.lincolnelectric.com
68281_233_288_ACG.indd 268 3/30/10 2:20 PM
[269]W E L D I N G C O N S U M A B L E S C A T A L O G
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
submerged arc (saW) electrode
WIRE COMPOSITION(1) - As Required per AWS A5.17/A5.17M:1997
%C %Mn %Si %S %P %Cu
Lincolnweld® L-50 0.06 - 0.16 0.90-1.40 0.35 - 0.75 0.030 0.030 0.35
Lincolnweld ® L-50
Recommended FluxesLincolnweld® 760, 761, 780, 781, 860, 865, 880M, 882, 888™, 8500, 960, 980, P223
�A low carbon, medium manganese, medium silicon wire
�Pair it with Lincolnweld® 980 flux for the best flux/wire combination when semiautomatic submerged arc welding
Mild Steel Solid ElectrodeAWS EM13K
Key Features
DIAMETERS / PACKAGING
Diameter 60 lb (27.2 kg)Coil
600 lb (272 kg)Speed Feed® Drum
1000 lb (453 kg)Speed Feed® Drum
1000 lb (453 kg)Accu-Trak® Drum
2200 lb (998 kg)Speed Feed® Stemin. (mm)
1/165/643/32
1/85/32
(1.6)(2.0)(2.4)(3.2)(4.0)
ED011317ED011335ED011328ED011323ED011332
ED011316ED011334ED011327ED011322ED011331
ED029083
ED032997
ConformancesEM13KMIL-70S-3
AWS A5.17/A5.17M: 1997MIL-E-23765/1D &1E:
(1)Single values are maximums.
68281_233_288_ACG.indd 269 3/30/10 2:20 PM
[270] T H E L I N C O L N E L E C T R I C C O M P A N Y
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® L-56submerged arc (saW) electrode
Recommended FluxesLincolnweld® 860, 880M, 882, 888, 8500, P223
�A low carbon, high manganese, very high silicon wire
�Can be used with Lincolnweld® 800 series fluxesforweldsrequiring480MPa(70ksi)tensile strength in stress relieved conditions
Mild Steel Solid ElectrodeAWS EH11K
Key Features ConformancesEH11KMIL-70S-6
AWS A5.17/A5.17M: 1997MIL-E-23765/1D & 1E:
WIRE COMPOSITION(1) - As Required per AWS A5.17/A5.17M:1997
%C %Mn %Si %S %P %Cu
Lincolnweld® L-56 0.06 - 0.15 1.40-1.85 0.80 - 1.15 0.030 0.030 0.35
DIAMETERS / PACKAGING
Diameter 60 lb (27.2 kg)Coil
500 lb (227 kg)Accu-Trak®
Drum
1000 lb (453 kg)
Speed Feed® Reel
1000 lb (453 kg)
Speed Feed® Drum
1000 lb (453 kg)
Accu-Trak® Drum
2200 lb (998 kg)
Speed Feed® Stemin. (mm)
1/165/643/32
1/85/32
(1.6)(2.0)(2.4)(3.2)(4.0)
ED011666ED011678ED011674ED011671EDS11677
ED029225EDS01631
ED030425ED030426ED028264
ED029085
ED032998ED032999
(1)Single values are maximums.
68281_233_288_ACG.indd 270 3/30/10 2:20 PM
[271]W E L D I N G C O N S U M A B L E S C A T A L O G
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
submerged arc (saW) electrode
Lincolnweld ® L-60
Recommended FluxesLincolnweld® 760, 761, 780, 781, 860, 882
�A low carbon, low manganese, low silicon general purpose electrode
�Provides the lowest hardness and is best suited for use with the Lincolnweld® 700 series of active fluxes
Mild Steel Solid ElectrodeAWS EL12; EN 756: S 1
Key Features ConformancesEL12S 1MIL-EL12
AWS A5.17/A5.17M: 1997EN 756:MIL-E-23765/4:
WIRE COMPOSITION(1) - As Required per AWS A5.17/A5.17M:1997
%C %Mn %Si %S %P %Cu
Lincolnweld® L-60 0.04-0.14 0.25 - 0.60 0.10 0.030 0.030 0.35
DIAMETERS / PACKAGING
Diameter 60 lb (27.2 kg)Coil
600 lb (272 kg)Speed Feed® Drum
1000 lb (453 kg)Speed Feed® Drumin. (mm)
1/165/643/32
1/85/32
(1.6)(2.0)(2.4)(3.2)(4.0)
ED011762ED011752ED011743ED011758ED011749
EDS11760
EDS11741
ED011761ED011751ED011742ED011757ED011748
(1)Single values are maximums.
68281_233_288_ACG.indd 271 3/30/10 2:20 PM
[272] T H E L I N C O L N E L E C T R I C C O M P A N Y
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® L-61submerged arc (saW) electrode
Recommended FluxesLincolnweld® 760, 761, 780, 781, 860, 865, 882, 888, 761-Pipe, P223, 960, 980, WTX, AXXX-10, 995N, SPX80
� Industry standard for submerged arc welding applications
�A low carbon, medium manganese, low silicon general purpose submerged arc electrode
�A good choice for a wide range of applications with single or multiple pass subarc welding
Mild Steel Solid ElectrodeAWS EM12K; EN 756: S 2Si
Key Features ConformancesEM12KS 2SiMIL-EM12K
AWS A5.17/A5.17M: 1997EN 756:MIL-E-23765/4:
WIRE COMPOSITION(1) - As Required per AWS A5.17/A5.17M:1997
%C %Mn %Si %S %P %Cu
Lincolnweld® L-61 0.05 - 0.15 0.80 - 1.25 0.10 - 0.35 0.030 0.030 0.35
(1)Single values are maximums.
DIAMETERS / PACKAGING
Diameter 60 lb (27.2 kg)Coil
300 lb (136 kg)Speed Feed® Reel
300 lb (136 kg)Speed Feed® Drum
600 lb (272 kg)Speed Feed® Drumin. (mm)
1/16 5/64 3/32 1/8 5/32 3/16
(1.6)(2.0)(2.4)(3.2)(4.0)(4.8)
ED011803ED011825ED011815ED011807ED011821ED011812
ED030412 ED030628
EDS11823EDS11813EDS11805EDS11819
Diameter 750 lb (340 kg)Speed Feed® Reel
1000 lb (453 kg)Speed Feed® Drum
2200 lb (998 kg)Speed Feed® Stemin. (mm)
1/16 5/64 3/32 1/8 5/32 3/16
(1.6)(2.0)(2.4)(3.2)(4.0)(4.8)
ED011826EDS11817EDS11809ED030012
ED011824ED011814ED011806ED011820ED011811
ED032973ED032972ED032994
68281_233_288_ACG.indd 272 3/30/10 2:20 PM
[273]W E L D I N G C O N S U M A B L E S C A T A L O G
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
submerged arc (saW) electrode
Lincolnweld ® L-S3
�A low carbon, high manganese, medium silicon electrode designed for use with the Lincolnweld® 800 series of neutral fluxes
�Capable of producing weld deposits with impactpropertiesexceeding27J(20ft•lbf) at-62°C(-80°F)whenusedwithLincolnweld® 888, 8500, and MIL800-H neutral fluxes
Mild Steel Solid ElectrodeAWS EH12K; EN 756: S 3Si
Key Features
Recommended FluxesLincolnweld® 860, 880M, 882, 888, 8500, MIL800-H, P223
ConformancesEH12KS 3Si
AWS A5.17/A5.17M: 1997EN 756:
WIRE COMPOSITION(1) - As Required per AWS A5.17/A5.17M:1997
%C %Mn %Si %S %P %Cu
Lincolnweld® L-S3 0.06 - 0.15 1.50 - 2.0 0.25 - 0.65 0.025 0.025 0.35
(1)Single values are maximums.
DIAMETERS / PACKAGING
Diameter 60 lb (27.2 kg)Coilin. (mm)
1/85/32
(3.2)(4.0)
ED016767ED016248
68281_233_288_ACG.indd 273 3/30/10 2:20 PM
[274] T H E L I N C O L N E L E C T R I C C O M P A N Y
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® LA-71submerged arc (saW) electrode
�A low carbon, medium manganese, medium silicon electrode containing approximately 0.1% titanium
�Small addition of titanium allows deposits to be stress-relieved with little loss of strength, even with extended stress relief times
�Widely used with neutral basic fluxes in both as-welded and post-weld heat treated conditions
Mild Steel Solid ElectrodeAWS EM14K
Key Features
Recommended FluxesLincolnweld® 860, 865, 880M, 882, 888, 8500, MIL800-H, 960, P223
ConformancesEM14KAWS A5.17/A5.17M: 1997
WIRE COMPOSITION(1) - As Required per AWS A5.17/A5.17M:1997
%C %Mn %Si %Ti %S %P %Cu
Lincolnweld® LA-71 0.06 - 0.19 0.90-1.40 0.35 - 0.75 0.03 - 0.17 0.025 0.025 0.35
(1)Single values are maximums.
DIAMETERS / PACKAGING
Diameter 60 lb (27.2 kg)Coil
1000 lb (453 kg)Speed Feed® Drumin. (mm)
3/321/8
5/32
(2.4)(3.2)(4.0)
ED011052ED011051ED011053
EDS30781EDS30782
68281_233_288_ACG.indd 274 3/30/10 2:20 PM
[275]W E L D I N G C O N S U M A B L E S C A T A L O G
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
submerged arc (saW) electrode
Lincolnweld ® L-70
�A low carbon, medium manganese, low silicon, 1/2% molybdenum wire used for single or multiple pass welds
�A standard choice for pipe fabrication and other limited pass applications
Low Alloy Solid ElectrodeAWS EA1; EN 756: S 2Mo
Key Features
Recommended FluxesLincolnweld® 761, 781, 860, 882, 888, 995N, 761-Pipe, P223, SPX80
ConformancesEA1S 2MoMIL-EA1
AWS A5.23/A5.23M: 2007EN 756:MIL-E-23765/4:
WIRE COMPOSITION(1) - As Required per AWS A5.23/A5.23M:2007
%C %Mn %Si %Mo %S %P %Cu
Lincolnweld® L-70 0.05 - 0.15 0.65 - 1.00 0.20 0.45-0.65 0.025 0.025 0.35
(1)Single values are maximums.
DIAMETERS / PACKAGING
Diameter 60 lb (27.2 kg)Coil
1000 lb (453 kg)Speed Feed® Drum
2200 lb (998 kg)Speed Feed® Stemin. (mm)
5/641/8
5/323/16
(2.0)(3.2)(4.0)(4.8)
ED012054ED012051ED012053ED012052
ED021192ED021193EDS21194
ED032971ED032970ED032996
68281_233_288_ACG.indd 275 3/30/10 2:20 PM
[276] T H E L I N C O L N E L E C T R I C C O M P A N Y
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® LA-75submerged arc (saW) electrode
�A low carbon, medium manganese, high silicon, nickel-bearing electrode designed for use with Lincolnweld® neutral fluxes
�Suitable for use in applications requiring less than 1% Ni wire composition
Low Alloy Solid ElectrodeAWS ENi1K
Key Features
Recommended FluxesLincolnweld® 860, 865, 880, 880M, 882, 888, MIL800-H, MIL800-HPNi, 960, 980
ConformancesENi1KAWS A5.23/A5.23M: 2007
WIRE COMPOSITION(1) - As Required per AWS A5.23/A5.23M:2007
%C %Mn %Si %Ni %S %P %Cu
Lincolnweld® LA-75 0.12 0.80-1.40 0.40-0.80 0.75 - 1.25 0.020 0.020 0.35
(1)Single values are maximums.
DIAMETERS / PACKAGING
Diameter 60 lb (27.2 kg)Coil
1000 lb (453 kg)Speed Feed® Drumin. (mm)
5/643/32
1/85/32
(2.0)(2.4)(3.2)(4.0)
ED011066ED011064ED011062ED011065
ED027225
ED027224
68281_233_288_ACG.indd 276 3/30/10 2:20 PM
[277]W E L D I N G C O N S U M A B L E S C A T A L O G
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
submerged arc (saW) electrode
Lincolnweld ® LA-81
�A low carbon, medium manganese, low silicon, 1/2% molybdenum wire containing small additions of titanium and boron for improved fracture toughness
�Generally used in two run applications for arctic grade line pipe
� It can be used to weld up to API X90 grade pipe
Low Alloy Solid ElectrodeAWS EG
Key Features
Recommended FluxesLincolnweld® 995N, SPX80
ConformancesEGAWS A5.23/A5.23M: 2007
WIRE COMPOSITION - As Required per AWS A5.23/A5.23M:2007
%C %Mn %Si %Mo %Ti %B %Cu
Lincolnweld® LA-81(1) 0.05 1.2 0.2 0.50 0.1 0.01 0.20
(1)No AWS limits. Values are typical.
DIAMETERS / PACKAGING
Diameter 60 lb (27.2 kg)Coil
1000 lb (453 kg)Speed Feed® Drum
2200 lb (998 kg)Speed Feed® Stemin. (mm)
1/85/323/16
(3.2)(4.0)(4.8)
ED023163 EDS31060ED032993ED032992ED032995
68281_233_288_ACG.indd 277 3/30/10 2:20 PM
[278] T H E L I N C O L N E L E C T R I C C O M P A N Y
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® LA-82submerged arc (saW) electrode
�Designed especially for high strength applications
�Recommendedwhenover620MPa(90ksi)tensile strength is required in the as-welded condition or when low temperature impact toughness is required in the stress-relieved condition
Low Alloy Solid ElectrodeAWS EF2
Key Features
Recommended FluxesLincolnweld® 860, 882, 888, 8500, MIL800-H
Conformances
EF2AWS A5.23/A5.23M: 2007
WIRE COMPOSITION(1) - As Required per AWS A5.23/A5.23M:2007
%C %Mn %Si %Ni %Mo %S %P %Cu
Lincolnweld® LA-82 0.10 - 0.18 1.70-2.40 0.2 0.40-0.80 0.40-0.65 0.025 0.025 0.35
(1)Single values are maximums.
DIAMETERS / PACKAGING
Diameter 60 lb (27.2 kg)Coilin. (mm)
3/321/8
5/32
(2.4)(3.2)(4.0)
EDS30785ED026958ED026959
68281_233_288_ACG.indd 278 3/30/10 2:20 PM
[279]W E L D I N G C O N S U M A B L E S C A T A L O G
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
submerged arc (saW) electrode
Lincolnweld ® LA-84
�A nickel-bearing electrode with 1/2% molybdenum
�Can be used for higher strength weldments where impact properties exceeding 27 J (20ft•lbf)at-62°C(-80°F)arerequired
�Suitable for use where consumables with less than 1% Ni are required
Low Alloy Solid ElectrodeAWS EF3; EN 756: S3 Ni1Mo
Key Features
Recommended FluxesLincolnweld® 860, 880M, 882, 888, P223, MIL800-H, MIL800-HPNi
Conformances
EF3S3 Ni1Mo
AWS A5.23/A5.23M: 2007EN 756:
DEPOSIT COMPOSITION(1) - As Required per AWS A5.23/A5.23M:2007
%C %Mn %Si %Ni %Mo %S %P %Cu
Lincolnweld®LA-84 0.10 - 0.18 1.75 - 2.20 0.2 0.80 - 1.0 0.45-0.60 0.010 - 0.020 0.010 - 0.020 0.05 - 0.15
(1)Single values are maximums.
DIAMETERS / PACKAGING
Diameter 60 lb (27.2 kg)Coil
1000 lb (453 kg)Speed Feed® Drumin. (mm)
3/32 (2.4) ED031871 ED031872
68281_233_288_ACG.indd 279 3/30/10 2:20 PM
[280] T H E L I N C O L N E L E C T R I C C O M P A N Y
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® LA-85submerged arc (saW) electrode
�A nickel-bearing wire with 0.2% molybdenum designed for use on weathering steels
�Capable of producing weld deposits with 480-550MPa(70-80ksi)tensilestrengthinthe as-welded and stress-relieved conditions
Low Alloy Solid ElectrodeAWS ENi5
Key Features
Recommended FluxesLincolnweld® 860, 880M, 882, 888, 8500, MIL800-H, MIL800-HPNi, 960
Conformances
ENi5AWS A5.23/A5.23M: 2007
WIRE COMPOSITION(1) - As Required per AWS A5.23/A5.23M:2007
%C %Mn %Si %Ni %Mo %S %P %Cu
Lincolnweld® LA-85 0.12 1.20 - 1.60 0.05 - 0.30 0.75 - 1.25 0.10 - 0.30 0.025 0.020 0.35
(1)Single values are maximums.
DIAMETERS / PACKAGING
Diameter 60 lb (27.2 kg)Coil
1000 lb (453 kg)Speed Feed® Drumin. (mm)
3/321/8
5/323/16
(2.4)(3.2)(4.0)(4.8)
ED023166ED023167ED023168ED023169
ED029965
68281_233_288_ACG.indd 280 3/30/10 2:20 PM
[281]W E L D I N G C O N S U M A B L E S C A T A L O G
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
submerged arc (saW) electrode
Lincolnweld ® LA-90
�A low carbon, high manganese, high silicon, 1/2% molybdenum special purpose wire
�Recommended for seam welding of pipe and for the general welding of high strength plate
Low Alloy Solid ElectrodeAWS EA3K
Key Features
Recommended FluxesLincolnweld® 880, 880M, 888, 8500, MIL800-H, 995N, P223, SPX80
Conformances
EA3KAWS A5.23/A5.23M: 2007
WIRE COMPOSITION(1) - As Required per AWS A5.23/A5.23M:2007
%C %Mn %Si %Mo %S %P %Cu
Lincolnweld® LA-90 0.05 - 0.15 1.60 - 2.10 0.50 - 0.80 0.40-0.60 0.025 0.025 0.35
(1)Single values are maximums.
DIAMETERS / PACKAGING
Diameter 60 lb (27.2 kg)Coil
750 lb (340 kg)Speed Feed® Reel
1000 lb (453 kg)Speed Feed® Drumin. (mm)
1/165/643/32
1/85/32
(1.6)(2.0)(2.4)(3.2)(4.0)
ED013999ED011086ED011084EDS11083EDS11085 EDS01154 EDS01152
68281_233_288_ACG.indd 281 3/30/10 2:20 PM
[282] T H E L I N C O L N E L E C T R I C C O M P A N Y
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® LA-92submerged arc (saW) electrode
�Designedforwelding11/4%chromium,1/2% molybdenum steels in high temperature service applications such as pressure vessels or piping
�The AWS R designator denotes ultra low residuals which will result in a low Bruscato factor(X-factor)
Low Alloy Solid ElectrodeAWS EB2R; EN 12070: Cr Mo1
Key Features
Recommended FluxesLincolnweld® 880M, 882, MIL800-H, 960
Conformances
EB2RCr Mo1
AWS A5.23/A5.23M: 2007EN 12070:
DIAMETERS / PACKAGING
Diameter 60 lb (27.2 kg)Coilin. (mm)
3/321/8
5/32
(2.4)(3.2)(4.0)
EDS30783EDS26960EDS26961
WIRE COMPOSITION(1) - As Required per AWS A5.23/A5.23M:2007
%C %Mn %Si %Cr %Mo %S %P %Cu
Lincolnweld® LA-92 0.07 - 0.15 0.45-1.00 0.05 - 0.30 1.00 - 1.75 0.45-0.65 0.025 0.025 0.35
(1)Single values are maximums.
68281_233_288_ACG.indd 282 3/30/10 2:20 PM
[283]W E L D I N G C O N S U M A B L E S C A T A L O G
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
submerged arc (saW) electrode
Lincolnweld ® LA-93
�Designed for high temperature applications such as pressure vessels and piping for 21/4%chromium,1%molybdenumsteels
�The AWS R designator denotes ultra low residuals which will result in a low Bruscatofactor(X-factor)
Low Alloy Solid ElectrodeAWS EB3R; EN 12070: Cr Mo2
Key Features
Recommended FluxesLincolnweld® 880M, 882, MIL800-H, 960
Conformances
EB3RCr Mo2
AWS A5.23/A5.23M: 2007EN 12070:
DIAMETERS / PACKAGING
Diameter 60 lb (27.2 kg)Coil
1000 lb (453 kg)Speed Feed® Drumin. (mm)
3/321/8
5/32
(2.4)(3.2)(4.0)
EDS30784EDS26962EDS26963
ED032185
WIRE COMPOSITION(1) - As Required per AWS A5.23/A5.23M:2007
%C %Mn %Si %Cr %Mo %S %P %Cu
Lincolnweld® LA-93 0.05 - 0.15 0.40-0.80 0.05 - 0.30 2.25 - 3.00 0.90 - 1.10 0.025 0.025 0.35
(1)Single values are maximums.
68281_233_288_ACG.indd 283 3/30/10 2:20 PM
[284] T H E L I N C O L N E L E C T R I C C O M P A N Y
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® LA-100submerged arc (saW) electrode
�A low carbon, high manganese wire with nickel and molybdenum designed to weld high strength steels such as HY-80 and HSLA-80
� Delivers yield strength greater than 690MPa(100ksi)
�Low H2 hydrogen levels can be achieved when used with MIL800-H flux
Low Alloy Solid ElectrodeAWS EM2 & ER100S-G & ER110S-G
Key Features
Recommended FluxesLincolnweld® 880, 880M, 888, MIL800-H, MIL800-HPNi, 960
ConformancesEM2MIL-100S-1 or MIL-100S-2 (withMIL800-H)
AWS A5.23/A5.23M: 2007MIL-E-23765/2D & /2E:*
DIAMETERS / PACKAGING
Diameter 60 lb (27.2 kg)Coilin. (mm)
1/165/643/32
1/85/32
(1.6)(2.0)(2.4)(3.2)(4.0)
ED010996ED011002ED010999ED010998EDS11001
WIRE COMPOSITION(1) - As Required per AWS A5.23/A5.23M:2007
%C %Mn %Si %Cr %Ni %Mo %Ti
Lincolnweld® LA-100 0.10 1.25 - 1.80 0.20 - 0.60 0.30 1.40-2.10 0.25 - 0.55 0.10
%Zr %Al %V %S %P %Cu
Lincolnweld® LA-100 0.10 0.10 0.05 0.015 0.010 0.25
(1)Single values are maximums.
*NAVSEATechnicalPublicationT9074-BC-GIB-010/0200
68281_233_288_ACG.indd 284 3/30/10 2:20 PM
[285]W E L D I N G C O N S U M A B L E S C A T A L O G
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
submerged arc (saW) electrode
Lincolnweld ® LC-72
�A cored wire designed to increase deposition rates 10-30% when used with 980 flux
�Designed to provide optimal bead shape, penetration, and slag removal in semiautomatic submerged arc welding
Mild Steel Cored ElectrodeAWS EC1
Key Features
Recommended FluxesLincolnweld® 980
Conformances
EC1AWS A5.17/A5.17M: 1997
DIAMETERS / PACKAGING
Diameter 50 lb (23 kg)Coil
300 lb (136 kg)Speed Feed® Reel
600 lb (272 kg)Speed Feed® Reel
600 lb (272 kg)Speed Feed® Drumin. (mm)
5/643/32
(2.0)(2.4)
ED011099ED011098 EDS01186 EDS27184 EDS01187
DEPOSIT COMPOSITION - As Required per AWS A5.23/A5.23M:2007
%C %Mn %Si %S %P %Cu
Lincolnweld® LC-72(1) 0.15 1.8 0.9 0.035 0.035 0.35
(1)Limits are for weld metal deposited with a particular flux (Lincolnweld® 980 flux).
68281_233_288_ACG.indd 285 3/30/10 2:20 PM
[286] T H E L I N C O L N E L E C T R I C C O M P A N Y
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® LAC-B2submerged arc (saW) electrode
�Designed to weld with either single or tandem arcs using a neutral flux
�Acost-effectivechoicewhenwelding11/4%chromium, 1/2% molybdenum steels where a lowBruscatofactor(X-factor)isnotrequired
Low Alloy Cored ElectrodeAWS ECB2
Key Features
Recommended FluxesLincolnweld® 880, 880M, 888
Conformances
ECB2AWS A5.23/A5.23M: 2007
DIAMETERS / PACKAGING
Diameter 50 lb (23 kg)Coil
600 lb (272 kg)Speed Feed® Drumin. (mm)
3/325/32
(2.4)(4.0)
ED010954ED010955
ED019581ED019582
68281_233_288_ACG.indd 286 3/30/10 2:20 PM
[287]W E L D I N G C O N S U M A B L E S C A T A L O G
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
submerged arc (saW) electrode
Lincolnweld ® LAC-M2
�Capableofdelivering690MPa(100ksi) yield strength when welded with Lincolnweld® 880, 880M, 888 or MIL800-H fluxes
Low Alloy Cored ElectrodeAWS ECM2
Key Features
Recommended FluxesLincolnweld® 880, 880M, 888, MIL800-H
Conformances
ECM2AWS A5.23/A5.23M: 2007
DIAMETERS / PACKAGING
Diameter 50 lb (23 kg)Coilin. (mm)
3/325/32
(2.4)(4.0)
ED010981ED010982
68281_233_288_ACG.indd 287 3/30/10 2:20 PM
[288] T H E L I N C O L N E L E C T R I C C O M P A N Y
fl
ux
-co
re
ds
ub
me
rg
ed
ar
cs
ta
inl
es
s &
nic
ke
lh
ar
df
ac
ing
Lincolnweld ® LAC-Ni2submerged arc (saW) electrode
�A 2% nickel electrode used primarily in weathering steel applications
�When used with 888 flux, it can produce impactpropertiesexceeding27J(20ft•lbf) at-73ºC(-100°F)
Low Alloy Cored ElectrodeAWS ECNi2
Key Features
Recommended FluxesLincolnweld® 880, 880M, 882, 888, 980
Conformances
ECNi2AWS A5.23/A5.23M: 2007
DIAMETERS / PACKAGING
Diameter 50 lb (23 kg)Coilin. (mm)
3/32 (2.4) ED010986
68281_233_288_ACG.indd 288 3/30/10 2:20 PM