Date post: | 04-Jun-2018 |
Category: |
Documents |
Upload: | nguyenkien |
View: | 250 times |
Download: | 2 times |
Fokker Dr.I
F36
1.5mmx175mm Carbon Rod
F46 F15F13
F12
F35
F37
F38F39
1.5mmx250mmCarbon Rod
F41
F44
F45
F17
F16
F22F40 F22-1
F21F43
F20
F19
F18
F5 F7
F6
F3
A5
A3
A2
A7
A1
A6
A4
A8
C5
C3
C3 C1C2
C6
C7
C4
C8
1.5mmx155mmCarbon Rod
C2C1
C7
W10
W9W71.5mmx347mm
Carbon Rod
W11
W43W3
W6
W18
W36
W37
W7
W39W40
W34W29
W34 W29
W30W30
W30
W29
W29
W29W42
W41W29
W29W30
W39-1
W21
W22
W6
W12
W13
W2W4
W3
W1
Outer:6x50mm Carbon TubeInner:3x98mm Carbon Tube
Install the aileron onto the upper wing by paper hinges.
3. Assemble the upper wing
1.Assemble the Fuselage 2.Assemble the wing of landing gear
3.1. Assemble the Aileron
BALSA WOOD AIRPLANEInstruction Manual
F25F8
F10
F11 F30
F32
F8
F9
F4F48
F35
F33
F26
F47
F23F1F22
F29
F34
F28
F2
F8-1
SpecificationWingspan:770mmLength:630mmNet weight:≈650g
Suggested EquipmentMotor: 2212 800-1000KVESC:20AServo:2.5g *2 & 5g *2 Propeller:7-8 inchBattery:2-3S 1300-1800mAh Radio≥3CH
W11
W14
W15
W7W6
W35W31
W31
W31
W31
W49
W57
W51
W52
W57
W29
W29
W29
W29
W29
W29
W29 W47
W48W46
W44W45
W7
W23
W20
W33
W32
W19
W29 W28W9
W10 W7
Inner:6x37mm Carbon Tube
Outer:3x77mm Carbon Tube
1.5mmx327mmCarbon Rod
W11
W10
W9
W8
W36W29
W29
W29
W29
W29
W29
W29
W29
W29
W55
W31
W31
W31W31
W31
W31
W56
W54
W25W24
W53
W26
W7
W16
W17
W27W7
W58
W50W50
Inner:6x37mm Carbon Tube
Outer:3x77mm Carbon Tube
1.5mmx294mmCarbon Rod
T7
T2
T6
T5
T4
T3
T1
T10
T14 T15T15
T17
T20T20
T17
T16
T18T18T18 T18T19T19
T11 T11
T12 T12
T13 T13
6.2. Assemble the wing
6.3 Install the landing gear and wing of langing gear.
6.3.3 Assemble and install the wheel.
6.3.1 Install the landing gear onto the fuselage.
6.3.2 Assemble the wing of landing gear.
Insert the steel wire rod
6.4 Assemble the cowling and scale parts.
7.1 Assemble the motor and motor mounting base.7.2 Assemble the servo and push rod for aileron.
7.3 Assemble the elevator rudder.
7.4 Assemble the servo horn and push rod for elevator and rudder.
8. Adjust the C.G
6.2.1. Plug and assemble together the middle wing,then install onto the fuselage.
Fix the horizontal tail with glue.
Glue the reinforcing bar here. Assemble the vertical tail onto the fuselage by paper hinges.
6.2.3. Plug and assemble together the lower wing,then install onto the fuselage.
6.2.4. Connect the upper,middle and lower wing by aluminum rod (as▲marked)
6.1Install the horizontal and vertical tail onto the fuselage.
5.1. Assemble the horizontal tail
screw
screw
screw
screwscrew
▲Insert through the preserve slots and fix with glue.
screw
screw
screwscale machine gun
rubber ring//wind shield
scale engine
cowling
carbon rod
Carbon fiber strip+screw
wheel stopper
7. Assemble the power system
B3
B2
B4
Diagram for push rod inside the fuselage
4. Assemble the middle wing
5. Assemble the lower wing
5.2. Assemble the vertical tail
6. Assemble the other components
T8
T9
6.2.2. Plug and assemble together the upper wing,then install onto the fuselage by aluminum rod and fix with screws.
125mmC.G