1
QDrum Heater M Material: Silicon Rubber Part Number W (Electric Power) V (Voltage) Weight (kg) Attaching Object Unit Price Type No. MDRHL 1 2000 200 5.0 Drum (200l) 2 560 3.0 Pail (20l) 3 700 4.0 18 liter metal can (18l) * Power Cable included (1.0m/MDRHL1: With Ground Wire, 3 conductors; MDRHL2, 3: No Ground Wire, 2 Conductors) * The setting range of the thermostat is at 30°C~110°C. Part Number MDRHL2 QPrecautions for Use 1Do not use it in flammable atmospheres. 2Install the heater below the fluid level. (Installation at the bottom of the drum is recommended.) 3To avoid burn injury, do not touch the heater when the power supply is on or immediately after the use. 4Do not use in places with rain fall. Standardized thermostat (30°C~110°C) and thermal fuse (184°C) prevents unexpected accidents. Q Features Drum Heaters are silicon rubber heaters for drums, pails and 18 liter metal cans. Liquid viscosity and the temperature can be properly controlled by the equipped temperature adjuster (liquid expansion type). It is lightweight, and can be installed and removed by a single person. Available for material preheating, viscosity control for high viscosity fluid and freeze prevention for liquid. QDrum Heater Temperature Change 80 70 60 50 40 30 20 1200V 4000W (2 Heaters) Surface Size of Rubber Heater 250x1780 Actual Heat Rise 50°C Water 200L ON 2200V 2000W (1 Heater) Temperature (°C) Hrs (h) 1 2 3 4 5 6 7 8 9 EMaximum Operating Temperature: 184°C EElectrical power plug is not included. EMDRHL2 and MDRHL3 don't have handles. MDRHL (Single-Phase 200V) (130) 40 1780 36 21 (1.5) 70 90 15 250 200 (200) 100 (100) Silicon Rubber Heater t1.5 Heat Plate Lead Wire 1,000mm Fastener Handle Clamp Mount Base Temperature Controller Stand Sensor Pocket Analog Temperature Adjuster Silicon Rubber Heater t1.5 Lead Wire Sensor Pocket Analog Temperature Adjuster 1.5 (60) Support Stand Power Cord (9) Spring Hook Lead Bushing 20 (100) 75 75 5.6842° 20 (60) (130) 100 860 R8601.59 R8411.59 200 190 (10) Silicon Rubber Heater t1.5 Stainless Steel Plate 1.5 Temperature Controller Stand Sensor Pocket Analog Temperature Adjuster (70) 80 150 75 150 75 150 80 (70) 250 900 (Low Heat-Generating Section) Spring Hook 20 20 (212) (10) Power Cord (60) 140 130 100 40 40 60 Configure Online -1529 2 -1530 2 Ribbon Heater Part Number L W (Electric Power) V (Voltage) Electrical Power Density (W/cm 2 ) Unit Price Type No. MRBH MRBHF MRBH MRBHF 1 1000 100 100 0.5 2 2000 200 3 1000 100 200 4 2000 200 5 3000 300 Type MMaterial Element Lead Wire Lead Wire Film MRBH Glass Cloth Nickel (Ni) Glass Lead MRBHF Glass Cloth (Fluorine Coating) Copper (Cu) Fluorine Lead QRibbon Heater 20 (60) L 40 10 Lead Wire (500) For 200V For 100V Element 2-Attachment String MRBH (Standard) MRBHF (Fluorine Coating Type) (100V, 200V / Single-phase) EMaximum Operating Temperature Standard Type : 350°C Fluorine Coating Type: 200°C EPlug is included with MRBH, MRBHF1-2 (for 100V). Part Number MRBH5 Ribbon Heater Heating Flask Nickel-Chrome Wire Glass Cloth Nickel-Chrome Wire Glass Cloth Heat Generator Outer Sheath Heat Generator Outer Sheath Fluorine Coating Ribbon Heater P P= L2 n n= L1 2 -L2 2 (πD) 2 ØD Length of Tube: L2 Length of Heater: L1 n: Number of Winds QFeature: Belt-shaped heaters easily attachable to piping and tanks. · Standard · Excels in heat resistance as the sheathing of the heater is glass cloth. QBasic Structure · This is a heater that has glass cloth covering the heat generating body. As for the fluorine coating type, the heat generating body is covered with glass cloth with a fluorine coating. QBasic Structure Diagram QHow to Mount · After winding over a pipe, fasten the heater with the mounting strap. · Fluorine Coating Type · As the fluorine coating has been applied on the glass cloth sheathing, particle generation is controlled. QPrecautions for Use EDo not let heater run idle in the atmosphere. It may cause fires and broken wire. Ensure the heater is closely contacted with a heated object when using. EPrevent the use of heaters from getting wet by water, oil or humidity, as the surface is glass cloth sheathing. EDo not install by overlapping the heater. EDo not use over the rated voltage (V). EWhen removing the heater from the heated object, make sure the power is turned off.Do not touch the heater immediately after the power is turned off. EUse the temperature controller for safety. QHow to Determine the Number of Winding Drum Heater Economy Type Configure Online Configure Online For Pricing and Days to Ship,Please Configure Online.
