Part No 1125061 1 Formula™TRE Setup Instructions

For more information regarding Invacare products, parts, and services, please visit www.invacare.com

Formula™TRE Setup Instructions

NOTE: Check all parts for shipping damage. In case of damage, DO NOT use. Contact Carrier/Invacare for further instructions.

SAFETY SUMMARYTo ensure the safe and proper setup of the Formula TRE seating system, these instructions MUST be followed:

� WARNINGDO NOT install this equipment without first reading and understanding this instruction sheet, the MK5™EX™and TT-EX™Electronics Service manual, part number 1114808 and the TDX™Owner’s Manual, part number 1114809. If you are unable to understand the warnings, cautions and instructions, contact a healthcare professional, dealer or technical personnel if applicable, before attempting to install this equipment - otherwise, injury or damage may occur.

� INSTALLATION WARNINGThis adjustment MUST be performed by a qualified technician.These adjustment instructions DO NOT apply to Elevate Only systems.After ANY adjustments, repair or service and BEFORE use, make sure that all attaching hardware is tightened securely.

Tool needed - 7/16 inch wrenchNOTE: For seating system operating instructions, refer to the Owner’s Manual, part number 1114809.NOTE: For remote programmer operating instructions, refer to the Electronics Service Manual, part number 1114808.

ADJUSTING THE DRIVE LOCKOUT LIMIT ANGLE

� WARNINGNEVER operate the wheelchair while in any tilted/reclined/back angle posi-tion over 20° RELATIVE TO THE VERTICAL POSITION. Drive lockout MUST not be adjusted beyond 20°.

NOTE: For this procedure, refer to FIGURE 1.1. Tilt or recline the seating system to the desired drive lockout limit angle below

20° relative to the vertical position.2. Plug the remote programmer into the controller.

Assembly, Installation and Operating Instructions

SAVE THESE INSTRUCTIONS

Formula™TRE Setup Instructions 2 Part No 1125061

3. Select ADVANCED MENU.4. Select CURRENT STATUS MENU.5. Scroll down to DRIVE LOCKOUT.6. Loosen the locknut securing the drive lockout clamp to the controller bracket.7. Move the drive lockout clamp in the following manner until the programmer

changes from FALSE to TRUE:• Towards the front of the wheelchair - Decreases the drive lockout angle.• Towards the rear of the wheelchair - Increases the drive lockout angle.

8. Tighten the locknut to secure the drive lockout clamp in the desired position.

FIGURE 1 - ADJUSTING THE DRIVE LOCKOUT LIMIT ANGLE

ADJUSTING THE TILT LIMIT ANGLENOTE: For this procedure, refer to FIGURE 2.

Drive Lockout Limit Switch

Locknut

Drive Lockout Clamp

Drive Lockout Limit Switch

DETAIL “A” - REAR VIEW

CONTOURA BACK

STANDARD BACK

Drive Lockout Limit Switch

LocknutDrive Lockout

Clamp

Controller Bracket

Controller Bracket

DETAIL “A” - REAR VIEW

Part No 1125061 3 Formula™TRE Setup Instructions

1. Tilt the seating system to the desired tilt limit angle.NOTE: This procedure is for adjusting the tilt down limit.2. Plug the remote programmer into the controller.3. Select ADVANCED MENU.4. Select CURRENT STATUS MENU.5. Scroll down to TILT DOWN LIMIT.6. Loosen the locknut securing the tilt limit switch clamp to the large limit switch

bracket.7. Move the tilt limit switch clamp in the following manner until the programmer

changes from FALSE to TRUE:• Towards the front of the wheelchair - Increases the tilt limit angle.• Towards the rear of the wheelchair - Decreases the tilt limit angle.

8. Tighten the locknut to secure the tilt limit switch clamp in the desired position.

FIGURE 2 - ADJUSTING THE TILT LIMIT ANGLE

CONTOURA BACK

Tilt Limit Switch

Locknut

Tilt Limit Switch Clamp

Large Limit Switch Bracket

STANDARD BACK

Tilt Limit Switch

Tilt Limit Switch Clamp

Locknut

Large Limit Switch Bracket

DETAIL “A” - SIDE VIEW

ADJUSTING THE RECLINE LIMIT ANGLENOTE: For this procedure, refer to FIGURE 3.1. Recline the seating system to the desired recline limit angle.NOTE: This procedure is for adjusting the recline down limit.2. Plug the remote programmer into the controller.3. Select ADVANCED MENU.4. Select CURRENT STATUS MENU.5. Scroll down to RECLINE DOWN LIMIT.6. Loosen the locknut securing the recline limit switch clamp to the controller

bracket.7. Move the recline limit switch clamp in the following manner until the

programmer changes from FALSE to TRUE:• Towards the front of the wheelchair - Decreases the recline limit angle.• Towards the rear of the wheelchair - Increases the recline limit angle.

8. Tighten the locknut to secure the recline limit angle bracket in the desired position.

FIGURE 3 - ADJUSTING THE RECLINE LIMIT ANGLE

Recline Limit SwitchRecline Limit Switch Clamp

LocknutController Bracket

DETAIL “A” - SIDE VIEW

CONTOURA BACK

STANDARD BACK

Recline Limit Switch

LocknutRecline Limit Switch Clamp

Controller Bracket

Invacare Corporation www.invacare.com

USAOne Invacare WayElyria, Ohio USA44036-2125800-333-6900

Canada570 Matheson Blvd E Unit 8Mississauga OntarioL4Z 4G4 Canada800-668-5324

Invacare is a registered trademark of Invacare Corporation.TDX, MK5, EX, TT-EX, Formula and Yes, you can. are trademarks of Invacare Corporation© 2004 Invacare Corporation

Part No 1125061

Rev A - 06/04