FPC Connector1.25mm Pitch B Product Specification Issued Date

2013-11-19

Document No:TWVM-RD010 Product Name: WTB CONN.1 of 5

Prepared By： G.X

Rechecked By：G.X

Approved By：LIUPENG

Update List:Item Update Description Rev. Issued Date Revisor1 New Edit A 2011/06/06 G.X2 Update the product code B 2013/11/19 G.X

FPC Connector1.25mm Pitch B Product Specification Issued Date

2013-11-19

Document No:TWVM-RD010 Product Name: WTB CONN.2 of 5

1. SCOPE1.1 Contents

This specification covers the performance, tests and quality requirements for the 1.25P WTB R/A SMTType Connector.

1.2 QualificationWhen tests are performed on the subject product line, the procedures specified in VM inspection plan andproduct drawings.

2. ORDERING INFORMATIONPART NO.：WTB 12 34 xx RX TA x x x

1 2 3 4 5 6 7 8 9

1 Series name WTB Connector

2 Pitch between contacts 12=1.25mmPitch

3 Height of product 34=3.4mm

4 Number of terminals 02~30

5 Assembly style Right angle contact type

6 Packaging TA=Tape reel

7 Plating type 0=Tin G=Gold flash 1=Au:1u’” 5=Au:5u’’

8 Environment number H＝HF；G＝GP；R＝ROHS

9 Other

3. CONNECTOR DIMENSIONSSee attached drawings.

4. MATERIAL

Housing : LCPColor : White

Flammability Rating (UL94V-0)

Terminal: Brass

Peg: Brass

Terminal Plating: See Ordering Information

Peg Plating: Tin over Nickel

5. ACCOMMODATED P.C.B. LAYOUTSee attached drawings.

FPC Connector1.25mm Pitch B Product Specification Issued Date

2013-11-19

Document No:TWVM-RD010 Product Name: WTB CONN.3 of 5

6.RATING.

ITEM STANDARD

Operating Voltage (Max.) 125V AC/DC

Current Rating (Max.) 1.0A AC/DC

Operating Temperature -25°C ~ +85°C (Including terminal temperature rise)

7. PERFORMANCE

ITEM TEST CONDITION REQUIRMENT

Examination of Product Visual inspection.NO physical damage.Meets requirements of productdrawing .

ELECTRICAL PERFORMANCE

Contact Resistance

Mate applicable W.T.B and measure by dry

circuit, 20mV Max, 10mA.

(JIS C5402 5.4)30 mΩ Max.

Insulation Resistance

Measure by applying test potential between theadjacent contacts ,and between the contacts andground in the method 302,(500 V DC±10%).

100 MΩ Min.

Dielectric Strength

Measure by applying test potential between theadjacent contacts ,Current Voltage:250V/AC rms.for 1 minute. MIL-STD-202, Method301.

No evidence of break-down andflashover

MECHANICAL PERFORMANCE

Terminal/Housing retention forceApply axial pull out force at the speed rate of 2±3mm/Min.on the terminal assembled in the housing

0.5kgf(5.0N)Min

Insertion Force ＆ RetentionForce

Pull out force at a speed of 25±3mm perminute Refer to paragrah

FPC Connector1.25mm Pitch B Product Specification Issued Date

2013-11-19

Document No:TWVM-RD010 Product Name: WTB CONN.4 of 5

ITEM TEST CONDITION REQUIRMENT

ENVIRONMENTAL PERFORMANCE AND OTHERS

Temperature Rise

Measure the temperature rise of contact when the

maximum AC

rated current is passed. (UL498)

Temperature

rise30°C Max.

Life testWhen mated up to 30cycles repeatedly (the rate is 10cycles per minute).

Contact

Resistance40 mΩ Max.

Vibration

Mate connectors and subject to the following

vibration conditions, for period of 2 hours in each of

3 mutually perpendicular axes, passing DC 1mA

during the test. Amplitude : 1.5mm P-P

Frequency : 10~55~10 Hz in 1 minute.

Duration : 2 hours in each of X,Y,Z axes.

(MIL-STD-202 Method 201)

Appearance No Damage

Contact

Resistance40 mΩ Max.

Discontinuity 1 μ sec Max.

Shock

Subject to the following shock conditions. 3 times of

shocks shall be applied for each 6 directions along

3 mutually perpendicular axes, passing DC 1 mA

current during the test. (Total of 18 shocks)

Peak value : 490m/s2 50G

(JIS C0041 / MIL-STD-202 Method 213)

Appearance No Damage

Contact

Resistance 40 mΩ Max.

Discontinuity 1 μ sec Max.

Heat Resistance

Expose to 85±2°C for 96 hours. Upon completion of

the exposure period, the test specimens shall be

conditioned at ambient room conditions for 1 to 2

hours, after which the specified measurements

shall be performed. (JIS C0021 / MIL-STD-202

Method108)

Appearance No Damage

Contact

Resistance40 mΩ Max.

Cold Resistance

Expose to -40±2°C for 96 hours.Upon completion ofthe exposure period, the test specimens shall beconditioned at ambient room conditions for 1 to 2hours, after which the specified measurements shallbe performed.(JIS C0020)

Appearance No Damage

ContactResistance

40 mΩ Max.

FPC Connector1.25mm Pitch B Product Specification Issued Date

2013-11-19

Document No:TWVM-RD010 Product Name: WTB CONN.5 of 5

ITEM TEST CONDITION REQUIRMENT

Humidity

Expose to 40 ± 2°C, relative humidity 90 to 95% for96 hours.Upon completion of the exposure period, the testspecimens shall be conditioned at ambient roomconditions for 1 to 2 hours, after which the specifiedmeasurements shall be performed.(JIS C0022 / MIL-STD-202 Method 103)

Appearance No Damage

ContactResistance

40 mΩ Max.

DielectricStrength

No Breakdown

InsulationResistance

50 MΩ Min.

Temperature Cycling

Subject to the following conditions for 5 cycles.Upon completionof the exposure period, the test specimens shall beconditioned at ambient room conditions for 1 to 2hours, after which the specified measurements shalbe performed.1 cycle a) -55±3°C 30minutes

b)+85±3°C 30minutes(Transit time shall be with in 3 minutes)(JIS C0025)

Appearance No Damage

ContactResistance 40 mΩ Max.

Salt Spray

Expose to the following salt mist conditions. Uponcompletion ofthe exposure period, salt deposits shall be removedby a gentle wash or dip in running water, afterwhich the specified measurements shall beperformed.NaCl solutionConcentration : 5 ± 1%Spray time : 48 ± 4 hoursAmbient temperature : 35 ± 2°C(JIS C0023 / MIL-STD-202 Method 101)

Appearance No Damage

ContactResistance

40 mΩ Max.

Solder abilitySolder Temperature: 245 ±5°CImmersion Period: 5±0.5sec

The test area shall be coveredmore than 95% of immersedarea with fresh solder.

Resistance toSoldering Heat

When reflowing…Refer to paragraph 8.Soldering iron method

Soldering time : 3 ±0.5seconds Max.Solder temperature : 380±5°C

Appearance No Damage

FPC Connector1.25mm Pitch B Product Specification Issued Date

2013-11-19

Document No:TWVM-RD010 Product Name: WTB CONN.6 of 5

8. INFRARED REFLOW CONDITION

NOTE: Please check the re-flow soldering condition by your own devices beforehand .Because the condition changes by the soldering devices, p.c. boards, and so on.

9. TAPE AND REEL PACKAGE SPECIFICATION9-1.Tape and Reel Dimensions：See attached drawings.9-2.SpecificationNo. ofContacts

At Initial At 30th No.ofContacts

At Initial At 30th

I.F.(MAX.) R.F.(MIN.) R.F.(MIN.) I.F.(MAX.) R.F.(MIN.) R.F.(MIN.)

02 2.00 0.28 0.18 11 6.50 0.62 0.52

03 2.50 0.30 0.20 12 7.00 0.65 0.55

04 3.00 0.33 0.23 13 7.50 0.68 0.58

05 3.50 0.38 0.28 14 8.00 0.71 0.61

06 4.00 0.43 0.33 15 8.50 0.74 0.64

08 5.00 0.53 0.43 20 11.00 0.89 0.79

09 5.50 0.56 0.46 25 13.50 1.04 0.94

10 6.00 0.59 0.49 30 16.00 1.19 1.09

10. TAPE AND REEL PACKAGE SPECIFICATION10-1. Tape and Reel Dimensiongs : See attached drawings.10.-2 Specification

No.of Terminals Width ?Pcs/Reel ？Reels/Carton

02~09 16 2000/1 12/1

10~14 24 2000/1 10/1

15 32 2000/1 8/1

Export Carton Layer : 3 Layers Carton Size : 350×350×34mm

0

50

100

150

200

230

250°C MAX.(Peak Temp.)3Sec. or less

230°C MIN. / 20～40Sec.°C

Start

60 Sec. 60～90 Sec. 30 Sec.

Time(sec.)