Frame Technical Data - Steel Dor of...

iIndex

FRAME TECHNICAL DATANovember 1, 2004ASSA ABLOY, the global leader

in door opening solutions

DESCRIPTION PAGE(S)

Anchors – Drywall FrameBase Anchor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35Compression Anchor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34, 36, 39Multipurpose Anchor Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17Steel Channel Anchor Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126Security Anchor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Anchors – Flush Frame (Masonry)Ceiling Strut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18Conduit Compatible . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75-76Existing Wall Anchors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9, 11, 12Floor Anchor (Foot Clip) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-7Loose Spline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128Masonry Anchors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-10Mullion Stirrup Anchor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18Multipurpose Anchor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16Steel Stud Anchor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13-14Wire Truss Anchor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Wood Stud Anchor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Borrowed Lite Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41-42Cabinet Jamb Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90CCW Stick Length Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109-120Communicating Frames/Mullion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96CURRIElum Emergency Egress Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132Curriseal Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92-93Currisound Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94-95Custom Frame Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121-122Double Egress Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2, 107Drywall Frames

Corner Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32-33Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36-38Throat Filler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Erection Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129-130ElectroLynx System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131Fabricaton Frame Corner Details

Cutting and Notching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27-31Field Splice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24Welded Corner Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-23

Flush Masonry FramesCorner Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5

iiIndexFRAME TECHNICAL DATAJuly, 2007 ASSA ABLOY, the global leader


DESCRIPTION PAGE(S)

Grout Hole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85Hardware

Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44-48Preparations

•Automatic Flush Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87•Closer Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77-81•Coordinator Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84•Deadlock Strike Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67•Electric Strike Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74, 88, 89•Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68-71

Exit Device Preparations•Rim Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73•Vertical Rod Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72

Flush Bolt Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86-87Hinge Preparations

•4-1/2" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50•5" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51•Anchor Hinge Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58•Continuous Hinge Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55•Electric Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52, 57•Double Acting Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59•Full width Hinge Reinforcement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54•High Frequency Hinge Reinforcement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53•Pocket Pivot Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60•Security Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

Mullion (Hardware Removable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83Pivots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63, 64Strikes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61, 65, 66, 70Surface Bolt Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83

Hospital Stops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100Lead Lined Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108Mullion

Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103Removable Mullion Vertical / Horzontal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104-105

Pocket Door Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97-98Rabbet Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49Rescue Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62Rough Buck Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91Security Sidelite Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .133Silencers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127Spats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99Stainless Steel Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25, 26StormPro® 361 Frame Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125Thermal Break Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101-102Transom Frame Removable Panel Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134Wall construction Details

Masonry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

1Flush Masonry KD Miter Corner Joint

FRAME TECHNICAL DATAApril 1, 2002

L

ASSA ABLOY, the global leaderin door opening solutions

#8 SCREW(REQUIRED ON ALL FIRERATED KD FRAMES)

HEAD

JAMB

SPOT WELDS

BREAK–OFF TOOL

JAMB

JAMB

BEND TABS

HEAD

CORNER ASSEMBLY2" (50.8) HEAD

BREAK AWAYCORNER CLIP

2-7/16"(61.9)

1-13/16"(46)

USING THE BREAK-OFF TOOL, BENDCLIP BACK AND FORTH TOWARD OPPOSITE FACE OF FRAME.DO NOT BEND PAST THE OUTSIDE FACE TO AVOID DEFORMING THE FACE.

NOTE: USING PLIERS TO BREAK OFFTHE CORNER CLIP MAY RESULT INDAMAGE TO THE FACE OF FRAME

2Masonry KD 4" Face HeadFRAME TECHNICAL DATAApril 1, 2002

L


Masonry KD Double Egress Frame

L


HEAD FILLERCORNER CLIP

BEND TABS


BEND TABS

* 5-3/4" (146.1) JAMB DEPTH HAS 7/16" (11.1) RETURN

4-3/4" - 14"(120.6) - (355.6)

1/2"*(12.7)

2-5/8"(66.7)

1-3/8"(34.9)

JAMBDEM

HEADGE 2-5/8"

(66.7)

4-3/4" - 14"(120.6) - (355.6)1/2"*

(12.7)

2"(50.8)

3Masonry KD “G” Profile - Corner Details


L


JAMBHEAD

CORNER ASSEMBLY

BEND TABS

Masonry KD 2" Face Flush Frame Unequal Rabbet

L1-15/16"(49.2)

VARIES 1-9/16"(39.7)

5/8"(15.9)

2"(50.8)

1/2"(12.7)

M

KD “M” TYPE FLUSHGAUGE - 18 GA. (1.2), 16 GA. (1.4), 14 GA. (1.9)VARIABLE SOFFITJAMB DEPTH 4-1/2" (114.3) THRU 14" (355.6) (1/8"(3.2) INCREMENTS)AVAILABLE WITH 4" (101.6) FACE HEADSNOTE: 5-3/4" (146.1) JAMB DEPTH STANDARD WITH 7/16" (11.1) RETURNSTO PROVIDE 4-7/8" (123.8) THROAT OPENING


4Masonry 1", 1-1/4", 1-1/2", 1-3/4", Face Flush KD FrameUnequal RabbetFRAME TECHNICAL DATAApril 1, 2002

L


1-15/16"(49.2)

VARIES 1-9/16"(39.7)

5/8"(15.9)

1" (25.4), 1-1/4" (31.8)1-1/2" (38.1), 1-3/4" (44.5)

1/2"(12.7)

KD “M” TYPE FLUSHGAUGE - 18 GA. (1.2), 16 GA. (1.4), 14 GA. (1.9)VARIABLE SOFFITJAMB DEPTH 4-1/2" (114.3) THRU 14" (355.6) (1/8"(3.2) INCREMENTS)NOT AVAILABLE WITH 4" (101.6) FACE HEADSNOTE: WHEN CCW MATERIAL IS USED IN CONJUNCTION WITH ABOVE, COORDINATE RABBET AND FACE DIMENSIONS 5-3/4" (146.1) JAMB DEPTH STANDARD WITH7/16" (11.1) RETURNS TO PROVIDE 4-7/8" (123.8) THROAT OPENING.

M

Masonry Flush KD Frame Equal Rabbet

L

VARIES

5/8"(15.9)

1" (25.4), 1-1/4" (31.8)1-1/2" (38.1), 1-3/4" (44.5)

2" (50.8)

1/2"(12.7)

M

1-15/16" (49.2)OR

1-9/16" (39.7)

1-15/16" (49.2)OR

1-9/16" (39.7)

KD “M” TYPE FLUSHGAUGE - 18 GA. (1.2), 16 GA. (1.4), 14 GA. (1.9) VARIABLE SOFFITJAMB DEPTH 4-7/8" (114.3) THRU 14" (355.6) (1/8"(3.2) INCREMENTS)AVAILABLE WITH 4" (101.6) FACE HEADS WITH 2" FACE JAMBS ONLYNOTE: WHEN CCW MATERIAL IS USED IN CONJUNCTION WITH ABOVE, COORDINATE RABBET AND FACE DIMENSIONS. 5-3/4" (146.1) JAMB DEPTH STANDARD WITH7/16" (11.1) RETURNS TO PROVIDE 4-7/8" (123.8) THROAT OPENING.

5Masonry Face Flush KD Frame

Cased Opening FRAME TECHNICAL DATA

April 1, 2002

L


VARIES3" (76.2) MINIMUM

1" (25.4)1-1/4" (31.8)1-1/2" (30.1)1-3/4" (44.5)

2" (50.8)

1/2"(12.7)

MK

KD “MK” TYPE FLUSHGAUGE - 18 GA. (1.2), 16 GA. (1.4), 14 GA. (1.9)JAMB DEPTH 3" (76.2) THRU 14" (355.6) (1/8" (3.2) INCREMENTS)NOTE: AVAILABLE WITH 4" (101.6) FACE HEAD WITH 4-1/2" (114.3) MINIMUM JAMB DEPTH 5-3/4" (146.1) JAMB DEPTH STANDARD WITH 7/16" (11.1) RETURNSTO PROVIDE 4-7/8" (123.8) THROAT OPENING.

Masonry Flush KD “G” Profile Frame

L

G

VARIES

2"(50.8)

1/2"(12.7)

1-15/16" (49.2)OR

1-9/16" (39.7)5/8"

(15.9)

2-5/8"(66.7)

KD “G” TYPE FLUSHGAUGE - 18 GA. (1.2), 16 GA. (1.4), 14 GA. (1.9)JAMB DEPTH 3" (76.2) THRU 14" (355.6) (1/8" (3.2) INCREMENTS)MIN. 4" JAMB DEPTH FOR LABELED FRAME WITH 1-15/16" RABBET AND 3-1/4" JAMB DEPTH FOR 1-9/16" RABBET.NOTE: 2" (50.8) AND 2-5/8" (66.7) FACE ON JAMBSAVAILABLE WITH 4" (101.6) FACE HEAD WITH 4-1/2" (114.3) MINIMUM JAMB DEPTH. 5-3/4" (146.1) JAMB DEPTH STANDARD WITH 7/16" (11.1) RETURNSTO PROVIDE 4-7/8" (123.8) THROAT OPENING.

*

* TOTAL DOOR ONLY MAY BE LABELED

6Standard Foot ClipsFRAME TECHNICAL DATAApril 1, 2002

L


2" (50.8)STANDARD

2" (50.8)

FACE MINUS 3/8" (9.5)LABEL REQUIREMENTS: FACEMINUS 1/2" (12.7) MAXIMUM

9/32" (7.1) DIA.

P0030STANDARD FOOT CLIP16 GA. (1.4)

P0081DOUBLE EGRESSFOOT CLIPS

P0030C TYPE FRAME

FACE MINUS 3/8" (9.5)LABEL REQUIREMENTS: FACEMINUS 1/2" (12.7) MAXIMUM

P0080G PROFILEJAMB DEPTH 4" (101.6) OR LESS

P0081G PROFILEGREATER THAN 4" (101.6) JAMB DEPTH

P0216 - 16 GA.FOR FACE WIDTH OVER 4"P0281 - 14 GA.P0284 - 12 GA.

7Adjustable Foot Clip


L


Adjustable Foot Clip - Cased Opening

L

FOOT CLIP SHIPPED LOOSE WITH 2-#12 SHEET METAL SCREWS

ANCHOR PART NUMBER: P0078

5/8" (15.7)3/4" (19.1)

16 GA. (1.4)

1/2" (12.7)

3-5/8" (92)

1/4" (6.4)4-5/8"

(117.5)

PER FACE DIMENSION16 GA. (1.4)

PER JAMB DEPTH

9/32" (7.1) DIA.

5/8" (15.7)3/4" (19.1)

16 GA. (1.4)

1/2" (12.7)

3-5/8" (92)

1/4" (6.4)4-5/8"

(117.5)

PER FACE DIMENSION16 GA. (1.4)

PER JAMB DEPTH

9/32" (7.1) DIA.

FOOT CLIP SHIPPED LOOSE WITH 2-#12 SHEET METAL SCREWS


8Common Walls For Masonry AnchorFRAME TECHNICAL DATAApril 1, 2002

L


BUTTED MASONRY-BRICK-TILE OR CONCRETE BLOCK

EXISTING MASONRY OR POURED CONCRETE.

WRAP MASONRY-BRICK-TILE OR CONCRETE BLOCK.

BUTTED MASONRY-BRICK-TILE OR CONCRETE BLOCK.

BUTTED MASONRY-BRICK-TILE OR CONCRETE BLOCK

9Masonry Wire Anchor


L


Concealed Existing Opening Anchor

L

ANCHOR PART NUMBER: P0098ORDER CODE LOOSE: MW

WIRE DIA. 3/16" (4.8) GALV.ANCHOR MAY BE BENTTO SUIT JAMB DEPTH

9" (228.6)

5-5/8"(142.9)

1-7/8"(47.6)

1-1/16"(27)

COUNTERSINK HOLE FOR3/8" (9.5) F.H. BOLT

9/16" (14.3) DIA.

ANCHOR PART NUMBER: CF004557100 ANCHORS W/PLASTIC PLUG

PLASTIC PLUG PART NUMBER: MS002600100 PLASTIC PLUGS

PLASTIC PLUG

3/4" (19.1) HOLE INCENTER OF SOFFIT

NOT DRILLED BY CURRIES

3/8" (9.5) BOLT & EXPANSION SHELL(NOT PROVIDED)

NOTE: ANCHORS AVAILABLE FOR 5-3/4" (146.1) JAMB DEPTH 2" FACE ONLY AVAILABLE AS SHIP LOOSE PART ONLY

2-1/2"(63.5)

10Masonry “T” AnchorFRAME TECHNICAL DATAApril 1, 2002

L


Weld in Type Masonry Anchor

L

ANCHOR PART NUMBER: P0069ORDER CODE LOOSE: M

10-3/4" (273.1)

2" (50.8)

16 GA. (1.4)

ANCHOR PART NUMBER: P0002ORDER CODE LOOSE: MLORDER CODE WELDED: WML

10-3/4" (273.1)

2" (50.8)

16 GA. (1.4)

11EWA Anchor

FRAME TECHNICAL DATANovember, 2004

L


FOR STANDARD RABBETED FRAMES 1-15/16" (49.2) X 1-9/16" (39.7)THE EWA ANCHOR IS AVAILABLE IN 5-1/2" (139.7) & 8-1/2" (215.9) SIZES TOFIT 5-3/4" (146.1) & 8-3/4" (222.3) STANDARD RABBETED FRAMES RESPECTIVELY.3/8" FLAT HEAD BOLT RECOMMENDED.

ANCHOR PART NUMBER: P0070ORDER CODE LOOSE: EWAORDER CODE WELDED: WEWA

-AVAILABLE AS SHIP-LOOSE ANCHOR-AVAILABLE FROM WAREHOUSE AS STOCK #CF004896-SPECIFY 5-1/2" (139.7) OR 8-1/2" (215.9) SIZE

1-1/2" MIN. 18, 16, 14 GA. (38.1)

MINIMUM

5-3/4" (146.1)8-3/4" (222.3)

ARCWELD

5-3/4" (146.1)8-3/4" (222.3)

5-1/2" (139.7)8-1/2" (215.9)

2-15/16" (74.6)4-7/16" (112.7)

2-9/16" (65.1)4-1/16" (103.2)

2-9/16"(65.1)

15/16"(23.8)

1"(25.4)

THE EWA ANCHOR MAY BE TRIMMED TO FIT ANY FRAME OF STANDARD RABBET OR SINGLE RABBET 8-3/4" (222.3) OR LESS IN JAMB DEPTHAND EQUAL RABBET 8-3/8" (212.7) OR LESS IN JAMB DEPTH

* 1-1/2" MINIMUM 12 GA.

NOTE: 1-7/8 MIN. STOP WIDTH FOR QM PROFILE

DIAMETER 3/8" (9.5) X 1-3/4" (44.5)EMBEDMENT LENGTH OR STEELEXPANSION SHELL OR 3/8" (9.5)FLATHEAD BOLT

12Pipe Spacer AnchorFRAME TECHNICAL DATAApril 1, 2002

L


Spacing Bracket Anchor

L

ANCHOR PART NUMBER: P0044ORDER CODE LOOSE: PSORDER CODE WELDED: WPS

NOTE: FACE DIMENSION FOR PROFILE MUST BE EQUAL

DIAMETER 3/8" (9.5) X 1-3/4" (44.5)EMBEDMENT LENGTH OR STEEL EXPANSION SHELL OR 3/8" (9.5) FLATHEAD BOLT

3/4" I.D.(19.1)

1"(25.4)

1-1/4" (31.7) MIN. 18, 16, 14 GA.*

COUNTERSUNK FLATHEAD BOLT

ARC WELD

ANCHOR PART NUMBER: P0146ORDER CODE LOOSE: SBORDER CODE WELDED: WSB

DIAMETER 3/8" (9.5) X 1-3/4" (44.5)EMBEDMENT LENGTH OR STEEL EXPANSION SHELL OR 3/8" (9.5) FLATHEAD BOLT

1-1/4" (31.7) MIN. 18, 16, 14 GA.*

COUNTERSUNK FLATHEAD BOLT

VARIES

1-13/64"(30.6)

1-13/64"(30.6)

1/2" (12.7) DIA.

16 GA. (1.4)

* 1-1/2" MIN. FOR12 GA.

* 1-1/2" MIN. FOR 12 GA.

13Steel Stud Channel Anchor

FRAME TECHNICAL DATAJuly 15, 2003

L


Steel Stud Channel Anchor - Double Egress

ANCHOR PART NUMBER: P0149ORDER CODE LOOSE: SCSLIP IN STEEL STUD ANCHOR“M” & “C” SERIES FRAME

ANCHOR PART NUMBER: P0169ORDER CODE LOOSE: WSCWELD IN STEEL STUD ANCHOR

ANCHOR PART NUMBER: P0149ORDER CODE LOOSE: SCSLIP IN STEEL STUD ANCHOR“M” SERIES FRAME

ANCHOR PART NUMBER: P0169ORDER CODE LOOSE: WSCWELD IN STEEL STUD ANCHOR

1-1/2"(38.1)

5/16"(7.9)

5/16"(7.9)

9/16"(14.3)

NOTE: MINIMUM FACE OF 1-1/4" (31.8) REQUIRED FOR THIS ANCHOR TYPE

3/4"(19.1)

3/8"(9.5)

19/32"(15.1)

5/8"(15.9)

1-11/16"(42.9)

1-1/4"(31.8)

ANCHOR PART NUMBER: P0259ORDER CODE LOOSE: FLUSH SLIP IN STEEL STUD ANCHOR“M” & “C” SERIES FRAME

14Flush Steel Stud AnchorFRAME TECHNICAL DATAJuly 1, 2003

L


ANCHOR PART NUMBER: P0243ORDER CODE WELDED: WSCFWELD IN CHANNEL TYPE STEEL STUD ANCHOR (DOUBLE STUD)(SPECIFY STUD SIZE) OR 3/4" DRYWALL CLEARANCE STANDARD.

1-3/16" (30.2)

1-3/16" (30.2)

16 GA. (1.4)

15Wood Stud Anchor


L


Wood Stud Anchors - Double Egress

L

SLIP IN WOOD STUD ANCHOR - “M” SERIES FRAME ONLYORDER CODE LOOSE: WS “A” DIMENSIONSANCHOR PART NUMBER: P0152 3-1/2" (88.9) STUD(SPECIFY STUD SIZE) P0152 3-5/8" (92.1) STUD

P0152 5-1/2" (139.7) STUDP0152 5-5/8" (142.9) STUD

WELD IN WOOD STUD ANCHOR ORDER CODE LOOSE: WWS “A” DIMENSIONSANCHOR PART NUMBER: P0148 3-1/2" (88.9) STUD(SPECIFY STUD SIZE) P0140 3-5/8" (92.1) STUD

P0142 5-1/2" (139.7) STUDP0144 5-5/8" (142.9) STUD

1" (25.4)

A

9/64" (3.6) DIA.

16 GA. (1.4)

1" (25.4)

A

9/64" (3.6) DIA.

16 GA. (1.4)

1" (25.4)

A

9/64" (3.6) DIA.

16 GA. (1.4)

3-1/4" (82.6)

1" (25.4)

A

9/64" (3.6) DIA.

16 GA. (1.4)

SLIP IN WOOD STUD ANCHOR ORDER CODE LOOSE: WS “A” DIMENSIONSANCHOR PART NUMBER: P0152 3-1/2" (88.9) STUD(SPECIFY STUD SIZE) P0152 3-5/8" (92.1) STUD

P0152 5-1/2" (139.7) STUDP0152 5-5/8" (142.9) STUD

WELD IN WOOD STUD ANCHOR ORDER CODE LOOSE: WWS “A” DIMENSIONSANCHOR PART NUMBER: P0148 3-1/2" (88.9) STUD(SPECIFY STUD SIZE) P0148 3-5/8" (92.1) STUD

P0148 5-1/2" (139.7) STUDP0148 5-5/8" (142.9) STUD

NOTE: SPECIFY JAMB OR HEAD ANCHOR WHEN ORDERING

16Adjustable Multipurpose AnchorFRAME TECHNICAL DATAApril 1, 2006 ASSA ABLOY, the global leader


ANCHOR PART NUMBER: P0027ANCHOR CODE: AMP

“A” DIMENSION = JAMB DEPTHS OF 4-3/8" (111.1) THRU 6-3/4" (171.5)2" (50.8) FACE FLUSH “M” SERIES OR DRYWALL “C” SERIESFIELD ADJUSTED TO JAMB DEPTH. AVAILABLE AS SHIP LOOSE PART ONLY

FOR USE AS:WOOD STUD ANCHORWIRE TRUSS ANCHORSTEEL CHANNEL ANCHOR

ANCHOR PART NUMBER: P0045ANCHOR CODE: MP

JAMB DEPTHS OF 4-3/4" (120.7) THRU 9-3/4" (247.6)2" (50.8) FACE FLUSH “M” SERIES OR DRYWALL “C” SERIES

Multipurpose Anchor

L

#12-24 X 1/2" (12.7)SLOTTED HEX WASHER HEAD

1/8" (3.2) DIA.

16 GA. (1.4)

A

BEND OR TRIM LEGS TO SUIT WALL CONDITIONS

BEND OR TRIM LEGS TO SUIT WALL CONDITIONS

NUMBER OF STIFFENERSDEPEND ON JAMB DEPTHS

5/32" (4) DIA.

18 GA. (1.4)

UNEQUAL RABBETS ONLY ON MASONRY WALLS

17Multi-Purpose Anchor Installation - Drywall Return Frame

FRAME TECHNICAL DATANovember, 2004

L


2. INSERT ANCHOR INTO FRAME THROAT TILTED AT APPROXIMATELYA 50˚ ANGLE AS SHOWN IN DETAIL “B”.

3. THE ANCHOR MUST ALSO BE INSERTED AT APPROXIMATELYA 20˚ ANGLE FROM THE RABBETS OF THE FRAME AS SHOWN IN DETAIL “B”. THE FLANGES ON THE ANCHOR MUST CLEAR THE BACKBEND RETURNS.

4. TWIST THE ANCHOR INTO PLACE BY APPLYING PRESSURE IN THE OPPOSITE DIRECTIONS TO EACH SIDE OF THE ANCHOR AS SHOWNIN DETAIL “C”.

5. ONCE THE ANCHOR HAS SNAPPED INTO PLACE, DETAIL “D”, TURN IT UP INTO THE CORRECT POSITION AS SHOWN IN DETAIL “E” LEGS SHOULD BE BENT BACK TO THE ORIGINAL POSITION IF NECESSARY.

1. BEND LEGS OF ANCHOR 90˚ AS SHOWN IN DETAIL “A” (LEGS MAY HAVE TO BE BENT FURTHER IN LATER STEPS).

DETAIL “A”

DETAIL “B”

DETAIL “C”

DETAIL “D”

DETAIL “E”

50˚

20˚

PUSH

PUSH LIFT UP

P0045

18Ceiling Strut AnchorFRAME TECHNICAL DATASeptember 1, 2005

L


Mullion Stirrup Anchor

L

ANCHOR PART NUMBER: P01594" (101.6)

1" (25.4)

3/8" (9.5) DIA.2 PLS.

VARIES

1/4" (6.4)

STRUT1/4" (6.4) X 1" (25.4) STEEL BAR1 REQ’D

WEDGES

1/4" (6.4)1/16" (1.6)

1-1/4" (31.8)WEDGE

1-1/8" (28.6)

VARIES

STRUT GUIDE16 GA. (1.4)

2 REQ’D

1-1/8" (28.6)

1-9/16" (39.7)


DIMENSION “B” VARIES WITH FACE DIMENSION2" (50.8) FACE MULLION “B” EQUALS 1-1/2" (38.1)

B9/32" (7.1) DIA.

1-1/2" (38.1)

VARIES WITHJAMB DEPTH

12 GA. (2.6)FIELD INSTALL #8 SMSMINIMUM EACH FACE

19Full Weld KD


L


CONTINUOUS WELD FACE SEAMGRIND AND FINISH SMOOTH

CONTINUOUS WELD JOINTSOF RABBET AND SOFFIT

WELD CODE FW

20Seam Weld Flush KD FRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


L

Saw Miter Weld

L

BEND TABS

CONTINUOUS WELD FACE SEAMGRIND AND FINISH SMOOTH

CONTINUOUS WELD INSIDE OF MITER

GRIND FACE AND FINISH SMOOTH

WELD CODE SW (KD)

GRIND FACE AND FINISH SMOOTH

TACK WELD RABBETAND SOFFIT

WELD CODE SMWWELD CODE SMT

21Saw Butt Weld


L


WELD CODE BEW (<3) WELD CODE BET (<3)

WELD CODE SBW (>3) WELD CODE SBT (>3)

22Corner WeldsFRAME TECHNICAL DATAJuly 1, 2003

L


WELD CODE BEF 10

23Splice Joints


L


Saw Miter Only

LNOTE: PREPARED FOR DISTRIBUTOR WELDING

WELD CODE FSP WELD CODE WSP

WELD CODE SMO

WELD CODE EBE

EXACTNO NOTCH

WELD CODE SBE

EXACTNOTCH TOP JAMBSNOTCH BOTH ENDS.(BLANK OR HEADS)

NOTE: FACTORY WELDEDFRAMES EXCEEDING 9' X 14'WILL BE PROVIDED WITHFIELD SPLICES

24Field Splice FramesFRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


FRAMES FACTORY WELDED AT CURRIES:

PROVIDE FIELD SPLICES FOR FRAMES THAT EXCEED OVERALL SIZE SHOWN.

FRAMES FACTORY WELDED AT REGIONAL SERVICE CENTERS:

14'0"(4267)WIDTH

9'0" (2743)HEIGHT

9'0" (2743)WIDTH

14'0"(4267)HEIGHT

14'0"(4267)WIDTH

8'0" (2438)HEIGHT

8'0" (2438)WIDTH

14'0"(4267)HEIGHT

25Saw Butt Weld Stainless Steel

FRAME TECHNICAL DATAApril 1, 2002ASSA ABLOY, the global leader


L

JAMB DEPTH+1/8" (3.2)

THROAT OPENING1" (25.4) LESS THANJAMB DEPTH

RETURN FILLERS

BACKWELD SEAM

1/8" (3.2)

JAMBHEAD

304 STAINLESS STEEL#4 FINISH SATIN GRAIN

THROAT OPENING1" (25.4) LESS THANJAMB DEPTH

JAMB DEPTH -1/8" (3.2)

NOTE: HEAD IS RECESSED 1/8" (3.2)WITH HAIRLINE SEAM EXPOSED

NOTE: GRAIN PATTERN IS VERTICAL ON HORIZONTALFRAME MEMBERS UNDER 4' (1219.2) LONG,OVER 4' (1219.2) LONG, GRAIN PATTERN IS HORIZONTAL

26Stainless Steel Sidelight FrameFRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


L

NOTE: HEAD IS RECESSED 1/8" (3.2)WITH HAIRLINE SEAM EXPOSED

NOTE: #1 GRAIN PATTERN IS VERTICAL ON HORIZONTAL MEMBERS UNDER 4' (1219.2) LONG#2 OVER 4' (1219.2) LONG, GRAIN PATTERN IS HORIZONTAL

NOTE: VERTICAL MEMBERS MUST RUN FULL HEIGHT

HORIZONTAL MEMBERSUNDERSIZED 1/8" (3.2)

VERTICAL MEMBERSOVERSIZED 1/8" (3.2)

304 STAINLESS STEEL#4 FINISH SATIN GRAIN

#1 #2

3' (914.4) 6' (1828.8)

JAMB DEPTH + 1/8" (3.2)

1/8" (3.2)

WELDEDJAMB DEPTH - 1/8" (3.2)

27Half Sidelight Window Option

FRAME TECHNICAL DATAJuly 15, 2003ASSA ABLOY, the global leader


OPTION BMOST COMMON

REMOVE BACKSIDEOF MULLION

L

OPTION AAS REQUIRED

L

SPLICE WELD SECTION TO MULLIONFILL AND GROUND SMOOTH,LABELED WHEN FULLY WELDED.

OPTION CAS REQUIRED

L

FILLER PLATEWITH STOP

NOTE: MAY BE LABELED WHENPROPERLY WELDED.

EXPOSED SEAMUNLESS FACTORYWELDED SEAM

28Cut and Notch OptionsFRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


L

CORNER: KD STANDARD WHEN POSSIBLEMUST MEET KD PARAMETERS

SAW MITER:* IF FACES OF HEAD AND JAMB ARE EQUAL

1. EXCEPT: 4" (101.6) FACE HEAD TO2" (50.8) FACE JAMB

BUTT END:* IF FACES ARE UNEQUAL

* SMO OR SBE MUST BE NOTED IN CONSTRUCTION COLUMN.

NOTE: MAY BE LABELED WHEN PROPERLY WELDED

NOTE: MAY BE LABELED WHEN FACE WELDED

SAW MITER

BUTT END

KD

29Cut and Notch Options



L

STRIKE MULLION: NOTCH TOPEXCEPTION: WILL RUN THROUGH HEAD IF HEAD PROFILE IS

DIFFERENT ON GLASS SIDEEXAMPLE: “M” PROFILE AT DOOR OPENING

“G” PROFILE AT WINDOW SIDERUN MULLION THROUGH IF HEAD FACES ARE DIFFERENT FROM DOOR SIDE TO GLASS SIDEOR IF FIELD SPLICE IS REQUIRED


NOTE: PROVIDES ACCESS FOR ELECTRICALCONDUIT OR GROUT

30Cut and Notch OptionsFRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


L

HORIZONTAL MULLION: NOTCH BOTH ENDS TO BUTTBETWEEN VERTICAL MEMBERSIS STANDARD PREPARATION


NOTCH STOP OFJAMB TO RECEIVE MULLION

TYPICAL REMOVABLEMULLION PREPARATION

OPTIONAL STANDARD

31Cut and Notch Options



L

MULLION:NOTCH TOP AND BOTTOM, WILLRUN THROUGH FROM HEAD TOTOP OF SILL

1. EXCEPTION: WILL RUN MULLIONTHROUGH TO FLOOR RATHER THANSPLICE 2 SECTIONS OF SILL TOGETHER

2. EXCEPTION: RUN MULLION THROUGH HEAD AND SILL IF FIELD SPLICEIS REQUIRED

NOTE: MAY BY LABELED WHEN PROPERLY WELDED

SILLS:NOTCH BOTH ENDS TO BUTT BETWEENVERTICAL MEMBERS

OPTIONALSTANDARD STANDARD

32Saw Butt EndFRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


L

Drywall KD “CG” Profile Corner Details


#8 SCREW(REQUIRED ON ALL FIRE RATED FRAMES)

L

WALL NOTCH JAMB FOR DRYWALL WALL CONSTRUCTION

OPTIONAL STANDARD

33Drywall KD Frame Corner Clip Detail



L

3-1/2" (88.9)

JAMB

HEAD2" FACE

2-3/8" (60.3)

2-3/8" (60.3)

#8 SCREW(REQUIRED ON ALLFIRE RATED FRAMES)

HEAD2" (50.8) FACE

SPOT WELDSBY CURRIES

*RETURN FILLER: P0071

HEAD4" (101.6) FACE

JAMB

WELDPROJECTIONS

C PROFILE CORNER

34Security AnchorFRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


L

Drywall Frame Compression Anchor

L

COMPRESSIONANCHOR

SECURITYANCHOR

45" (1143) TYPICAL

BOTTOM OF FRAME

PER JAMBDEPTH

VARIES

1-1/8" (28.6)

1-1/8" (28.6)

3-1/2" (88.9)16 GA. (1.4)


5/8" (15.8)MAXIMUM TRAVEL

ANCHOR PART NUMBER: P0026 (2" FACE)ANCHOR PART NUMBER: P0018 (1-1/2" TO 1-3/4" FACE)

COMPRESSIONANCHOR

3-1/2" (88.9)1" (25.4)MIN.

35Drywall KD Frame Standard Base Anchor

FRAME TECHNICAL DATANovember, 2004ASSA ABLOY, the global leader


L

Drywall KD Frame Optional Base Anchor

L

3/4" (19.1)

5/8" (15.9)

2" (50.8)

ANCHOR HOLESCOUNTERSUNK

#6 SCREWBOTH SIDES

3-1/4" (82.6)

1" (25.4)

7/8" (22.2)

1/2" (12.7)

1/2" (12.7)

3/16" (4.8) DIA.

16 GA. (1.4)


NOTE: REQUIRED ON 1-1/2" (38.1), 1-3/4" (44.5) FACE DRYWALL FRAMES. 3", 3-1/8", 3-1/4", JAMB DEPTHS.

2" FACEONLY

3/4" (19)

FLOOR

CL

MINIMUM JAMB DEPTH 3-3/8 (85.7)

36Drywall CG ProfilesFRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


L

Compression Anchor System Narrow Jamb Depth

L

3" (76.2) – 14" (355.6)

VARIES1-15/16" (49.2)

OR1-9/16" (39.7)

JAMB DEPTHS

2-5/8" (66.7)2" (50.8)

5/8" (25.9)

1/2" (12.7)

3/8" (9.5)

1/2" (12.7)

3/8" (9.5)

GAUGE - 18 GA. (1.2), 16 GA. (1.4)NOTE: AVAILABLE WITH 4" (101.6) FACE HEAD WITH 4-1/2" (114.3) MINIMUM JAMB DEPTH

CG PROFILE *1-3/8" (34.9) DOOR - 3" (76.2) JAMB DEPTH1-3/4" (44.5) DOOR - 3" (76.2), 3-1/8" (79.4), 3-1/4" (82.6), 3-3/8" (85.7) JAMB DEPTH

ROUGH OPENING WIDTHEQUALS NOMINAL DOOROPENING: PLUS 2-13/16" (71.4)

ROUGH OPENING HEIGHTEQUALS NOMINAL DOOROPENING: PLUS 3/4" - 1" MAX

(19.1) - (25.4)

STRAP BASE ANCHOR

3/4" (19.1)

-COMPRESSION ANCHORS 3-1/2" (88.9)CL

STROKE

* “CG” PROFILE JAMB DEPTHS NOT LISTED ABOVE USE STD. DRYWALL ROUGH OPENING DIMENSIONS

CG

37Drywall KD Frame Unequal Rabbet



L

Drywall KD Frame Equal Rabbet

L

1-1/2" (38.1)1-3/4" (44.5)

2" (50.8)

5/8" (15.9)

1-15/16"(49.2)

1-9/16"(39.7)

VARIES

3/8" (9.5)

1/2"(12.7)

KD DRYWALLGAUGE - 18 GA. (1.2), 16 GA. (1.4), 14 GA. (1.9) *UNEQUAL RABBETJAMB DEPTH 4-1/2" (114.3) THRU 14" (355.6) (1/8" (3.2) INCREMENTS)2" (50.8) FACE AVAILABLE WITH 4" (101.6) HEADSNOTE: 14 GA. AVAILABLE WITH 2" (50.8) FACE ONLY

1-1/2" (38.1)1-3/4" (44.5)

2" (50.8)

5/8" (15.9)

1-15/16" (49.2)OR

1-9/16" (39.7)VARIES

3/8" (9.5)

1/2"(12.7)

1-15/16" (49.2)OR

1-9/16" (39.7)OR OR

C

C

KD DRYWALLGAUGE - 18 GA. (1.2), 16 GA. (1.4), 14 GA. (1.9) *UNEQUAL RABBETJAMB DEPTH 4-7/8" (123.8) THRU 14" (355.6) (1/8" (3.2) INCREMENTS)2" (50.8) FACE AVAILABLE WITH 4" (101.6) HEADSAVAILABLE IN COMMUNICATING FRAMESNOTE: 14 GA. AVAILABLE WITH 2" (50.8) FACE ONLY

38Drywall KD Frame Cased OpeningFRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


L

Drywall KD “CG” Profile Frame

L

VARIES3" (76.2) MINIMUM

1-1/2" (38.1)1-3/4" (44.45)

2" (50.8)

3/8" (9.5)

1/2" (12.7)

KD DRYWALLGAUGE - 18 GA. (1.2), 16 GA. (1.4), 14 GA. (1.9)JAMB DEPTH 3" (76.2) THRU 14" (355.6) (1/8" (3.2) INCREMENTS)14 GA. AVAILABLE W/2" FACE ONLY

NOTE: AVAILABLE WITH 4" (101.6) FACE HEAD WITH 4-1/2" (114.3) MINIMUM JAMB DEPTHWITH 2" FACE JAMBS ONLY.

VARIES

2" (50.8)

3/8" (9.5)

1/2" (12.7)

1-15/16" (49.2)

1-9/16" (39.7)OR

5/8" (50.8)

2-5/8" (66.7)

KD “CG” PROFILE DRYWALLGAUGE - 18 GA. (1.2), 16 GA. (1.4)JAMB DEPTH 3" (76.2) THRU 14" (355.6) (1/8" (3.2) INCREMENTS)NOTE: 2" (50.8) AND 2-5/8" (66.7) FACE ONLY

CK

CG

39Drywall Cased Opening Compression Anchor



L

CM Profile Frames

L

2" (50.8) LEG

STIFFENER PART NUMBER: P0093

16 GA. (1.4)

VARIES2" (50.8)

3/4" (19.1)

NOTE: STIFFENER ADDED TO PREVENT DISTORTION OF FRAME WHEN TIGHTENING ANCHOR

FOOTCLIPS

CM 3-1/2" (88.9) - 14" (355.6)CMG 3" (76.2) - 14" (355.6)

2" (50.8) CM CMG

CM PROFILE FRAMES DO NOT HAVE THE COMPRESSION BARNOR BASE ANCHORS. THEY DO HAVE FOOTCLIPS WELDED INAND ARE FURNISHED WITH LOOSE M.P. OR WIRE ANCHOR.WELDED IN ANCHORS ARE OPTIONAL. SAME K.D. CORNERCAPABILITIES AS THE C FRAME. THESE FRAME PROFILES ARE TO BE WELDED CORNER CONSTRUCTION WHEN INSTALLED.

* MAY BE LABEL APPROVED WITH PROPERLY WELDED FRAME CORNERS.

40Drywall KD Frame (“C” Profile) Installation InstructionsFRAME TECHNICAL DATASeptember, 2006 ASSA ABLOY, the global leader


3

4

2

57 6 7

8

9

1. CONSTRUCT WALL WITH ROUGH OPENING HEIGHT EQUAL TO FINISHED OPENING HEIGHT PLUS 3/4" (19.1) TO 1" (25.4)MAX., ROUGH OPENING WIDTH IS AS FOLLOWS:A) FOR 2" (50.8) FACE FRAMES-OPENING WIDTH PLUS 2-1/8" (54.0) TO 2-3/8" (60.3)B) FOR 1-3/4" (44.5) AND 1-1/2" (38.1) FACE FRAMES-OPENING WIDTH PLUS 2" (50.8)C) FOR “C” AND “CG” PROFILES, 3" (76.2) JAMB DEPTH 1-9/16" (39.7) RABBET AND 3" (76.2), 3-1/8" (79.4),

3-1/4" (82.6) AND 3-3/8" (85.7) JAMB DEPTH 1-15/16" (49.2) RABBET FRAMES-OPENING WIDTH PLUS2-13/16" (71.4), ALL OTHER “C” AND “CG” PROFILE FRAMES-OPENING WIDTH PLUS 2-1/8" (54.0) TO2-3/8" (60.3)

d) FOR 2" (508) FACE CASED OPENING - OPENING WIDTH PLUS 2-1/4" (572)

2. IF WRAP-AROUND BASE ANCHOR IS USED, NOTCH DRYWALL IN THAT AREA.

3. RETRACT COMPRESSION BARS IN THE JAMBS AND INSTALL ONE JAMB IN POSITION ON WALL.

4. INSERT FRAME HEAD UNDER THE CORNER CLIPS OF THE JAMB AND RAISE INTO POSITION.

5. INSERT THE CORNER CLIPS OF THE REMAINING JAMB INTO THE OPPOSITE END OF THE HEAD AND POSITION JAMB ON WALL.

6. LOCATE A REMOVABLE FRAME SPACING BAR AT BASE OF CENTERED FRAME TO MAINTAIN PROPER OPENING WIDTH DURING INSTALLATION.

7. SQUARE AND PLUMB FRAME AND INSTALL BASE ANCHOR SCREWS THROUGH COUNTERSINK HOLES IN FRAME FACE AND INTO FLOOR PLATE.

8. SQUARE TOP OF FRAME AND TIGHTEN COMPRESSION BARS. (DO NOT OVER TIGHTEN).

9. INSTALL (4) NO. 8 X 1/2" (12.7) SHEET METAL SCREWS AT THE CORNERS OF THE HEAD TO ATTACH HEAD TO JAMBS (REQUIRED FOR FIRE RATED FRAMES).

L


41Drywall KD Borrowed Lite

FRAME TECHNICAL DATAJuly, 2007

L

OVERALL FRAMEWIDTH

NOTE A: ROUGH OPENING HEIGHT FOR 2" (50.8) FACE FRAMES EQUALSGLASS OPENING SIZE PLUS 2-1/2" (63.5) INCLUDING CASED OPENINGNOTE A: ROUGH OPENING HEIGHT FOR 1-1/2" (38.1) & 1-3/4" (44.5) FACE FRAMESEQUALS GLASS OPENING SIZE PLUS 2" (50.8)

NOTE B: ROUGH OPENING WIDTH FOR 2" (50.8) FACE FRAMES EQUALSGLASS OPENING SIZE PLUS 2-1/2" (63.5) INCLUDING CASED OPENINGROUGH OPENING WIDTH FOR 1-1/2" (38.1) & 1-3/4" (44.5) FACE FRAMESEQUALS GLASS OPENING SIZE PLUS 2" (50.8)

NOTE:5/8" (15.8) X 5/8" (15.8) GLASS STOPSARE PUNCHED AND CUT TO LENGTH REMOVABLE STOPS MATCH FIXED STOPLENGTH AND ARE SHIPPED LOOSE

KD BORROWED LITE (DRYWALL FRAME ONLY)ORDER OF INSTALLATION - A) PLACE RIGHT SIDE VERTICAL JAMB MEMBER INTO OPENING; B) INSTALL SILLMEMBER AND ASSEMBLE CORNER #1; C) THEN INSTALL HEAD MEMBER AND ASSEMBLE CORNER #2 D) WHILEINSTALLING THE REMAINING LEFT VERTICAL JAMB MEMBER IT MAY BE NECESSARY TO EXTEND THE HEAD(CORNER #3) AND SILL (CORNER #4) TO THEIR ROUGH OPENING LIMITATIONS FOR EASIER INSTALLATION; E)THEN ASSEMBLE CORNER #3 AND FINALLY SNAP INTO POSITION THE REMAINING CORNER #4; F) INSTALLSCREWS THROUGH FRAME RETURNS INTO CORNER CLIPS; G) ADJUST COMPRESSION BARS UNTIL LEVEL ANDPLUMB.

GLASS OPENING1'6" (457.2) MINIMUM

ROUGH OPENINGHEIGHT

SEE NOTE A

OVERALL FRAMEHEIGHT

GLASSOPENING

VARIABLEFACE

ROUGH OPENING WIDTHSEE NOTE B

CL

CL

COMP.BAR

STD.

CL

CL

COMP.BAR

STD.

33

44 1

1

22

4" (101.6) FACE HEADS & SILLSARE NOT AVAILABLE.

“CG” PROFILE - SEE NEXT PAGE

VARIABLEFACE


42Single Rabbet Drywall KD Borrowed LiteFRAME TECHNICAL DATAJuly, 2007

An ASSA ABLOY Group company ASSA ABLOY

L

OVERALL FRAMEWIDTH

“CG” PROFILE - COMPRESSION BAR RABBET MOUNTED.JAMB DEPTHS INCLUDE 3" (76.2), 3-1/8" (79.4), 3-1/4" (82.5), 3-3/8" (85.7) X 1-15/16" (49.2) RABBETAND 3" (76.2) X 1-9/16" (39.7) RABBET

NOTE A: ROUGH OPENING HEIGHT FOR 2" (50.8) FACE FRAMES EQUALSGLASS OPENING SIZE PLUS 2-3/4" (69.8)

NOTE B: ROUGH OPENING WIDTH FOR 2" (50.8) FACE FRAMES EQUALSGLASS OPENING SIZE PLUS 2-1/2" (63.5)

KD BORROWED LITE (DRYWALL FRAME ONLY)ORDER OF INSTALLATION - A) PLACE RIGHT SIDE VERTICAL JAMB MEMBER INTO OPENING; B) INSTALL SILLMEMBER AND ASSEMBLE CORNER #1; C) THEN INSTALL HEAD MEMBER AND ASSEMBLE CORNER #2 D) WHILEINSTALLING THE REMAINING LEFT VERTICAL JAMB MEMBER IT MAY BE NECESSARY TO EXTEND THE HEAD(CORNER #3) AND SILL (CORNER #4) TO THEIR ROUGH OPENING LIMITATIONS FOR EASIER INSTALLATION; E)THEN ASSEMBLE CORNER #3 AND FINALLY SNAP INTO POSITION THE REMAINING CORNER #4; F) INSTALLSCREWS THROUGH FRAME RETURNS INTO CORNER CLIPS. G) ADJUST COMPRESSION BARS UNTIL LEVEL ANDPLUMB.

GLASS OPENING1'6" (457.2) MINIMUM

HEIGHTWIDTH

SEE NOTE A

OVERALL FRAMEHEIGHT

GLASSOPENING

VARIABLEFACE

ROUGH OPENING WIDTHSEE NOTE B

CL

CL

COMP.BAR

CL

CL

COMP.BAR

33

44 1

1

22

4"(101.6)

4"(101.6) #8 SHEET

METAL SCREW(8 PLACES)

VARIABLEFACE

43Throat Filler for Drywall Frames



L

INSTALLATION

1. FOR BEST RESULTS INSTALL FRAME IN OPENINGFIRST. DO NOT TIGHTEN COMPRESSION ANCHORS.

2. CUT JAMB FILLER STRIPS TO OVERALL LENGTHOF JAMB BACKBEND. CUT HEAD FILLER STRIP1" (25.4) UNDER OVERALL LENGTH OF HEAD BACKBEND.

3. REMOVE PROTECTIVE FILM FROM ADHESIVE TAPEAND APPLY FILLER STRIPS TO FRAME BACKBENDSWITH 1/8" (3.2) THICK LEG BETWEEN BACKBENDRETURN AND WALL. APPLY PRESSURE TO SEAT FIRMLY.

4. SQUARE FRAME, TIGHTEN COMPRESSION ANCHORS, INSTALL BASE ANCHORS AND RESEAT FILLERSTRIPS IF NECESSARY.

FILLER EQUALS OVERALL LENGTH OF BACKBEND

1/2"(12.7)

1/2"(12.7)LENGTH OF

HEAD FILLER

OVERALL LENGTH OF HEAD BACKBEND

THROAT FILLER STRIPS ARE MADE OF WHITE RIGID PVC WITH RESILIENT DOUBLE FACE TAPE FOR APPLICATION TO THEFRAME BACKBEND OR AFTER THE FRAME HAS BEEN INSTALLED.

SUPPLIED IN LENGTHS OF 7 FT. 3 IN. (2209.8) TO ACCOMMODATE MOST JAMB HEIGHTS WITH A CONTINUOUS STRIP.

NOTE: THROAT FILLER IS NOT ALLOWED ON LABEL FRAMES

THROAT REDUCEDBY 1/8" (3.2)

ONE FILLER STRIP

THROAT REDUCEDBY 1/4" (6.4)

TWO FILLER STRIPS

1/8" (3.2)DOUBLE FACE TAPE

FULL SIZE

44CURRIES Standard Hinge & Strike Locations for 1-3/4" FramesFRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


L

* STRIKE BACKSET: 5/16" (7.9) FOR 1-3/4" (44.5) DOOR1/2" (12.7) FOR 2" (50.8) DOOR

CL

CL

CL

CL

A

B

B

C

40" (1016) STANDARD

HINGE SIZE MAY VARY LOCATION REMAINS THE SAME.HINGE BACKSET: 5/16" (7.9) FOR 1-3/4" (44.5) DOOR.

5/8" (15.9) FOR 2" (50.8) DOORDOOR RABBETS: 1-15/16" (49.2) FOR 1-3/4" (44.5) DOOR.

2-3/16" (55.6) FOR 2" (50.8) DOOR.

FOR USE WITH THREE HINGES4-1/2" (114.3) OR 5" (127)

*

4-7/8" (123.8)STRIKE

SIZE A B C6’8” (2032) 7-1/4” (184.2) 30-1/4” (768.4) 12-1/4” (311.2)

6’10” (2082.8) 7-1/4” (184.2) 31-1/4” (793.8) 12-1/4” (311.2)7’0” (2133.6) 7-1/4” (184.2) 32-1/4” (819.2) 12-1/4” (311.2)7’2” (2184.4) 7-1/4” (184.2) 33-1/4” (844.6) 12-1/4” (311.2)7’10” (2387.6) 7-1/4” (184.2) 37-1/4” (946.2) 12-1/4” (311.2)8’0” (2438.4) 7-1/4” (184.2) 38-1/4” (971.6) 12-1/4” (311.2)

LLLLL

CL

45CURRIES Standard Hinge & Strike Locations for 1-3/4" Frames



LSIZE A B C

6'8" (2032) 7-1/4" (184.2) 20-1/8" (511.2) 12-3/8" (314.3)6'10" (2082.8) 7-1/4" (184.2) 20-7/8" (530.2) 12-1/8" (308)7'0" (2133.6) 7-1/4" (184.2) 21-1/2" (546.1) 12-1/4" (311.2)7'2" (2184.4) 7-1/4" (184.2) 22-1/8" (562) 12-3/8" (314.3)7'10" (2387.6) 7-1/4" (184.2) 24-7/8" (631.8) 12-1/8" (308)8'0" (2438.4) 7-1/4" (184.2) 25-1/2" (647.7) 12-1/4" (311.2)9'0" (2743.2) 7-1/4" (184.2) 29-1/2" (749.3) 12-1/4" (311.2)10'0" (3048) 7-1/4" (184.2) 33-1/2" (850.9) 12-1/4" (311.2)

LLLLLLL

* STRIKE BACKSET: 5/16" (7.9) FOR 1-3/4" (44.5) DOOR1/2" (12.7) FOR 2" (50.8) DOOR

CL

CL

CL

CL

CL

A

B

B

C

40" (1016) STANDARD

HINGE SIZE MAY VARY LOCATION REMAINS THE SAME.HINGE BACKSET: 5/16" (7.9) FOR 1-3/4" (44.5) DOOR.

5/8" (15.9) FOR 2" (50.8) DOORDOOR RABBETS: 1-15/16" (49.2) FOR 1-3/4" (44.5) DOOR.

2-3/16" (55.6) FOR 2" (50.8) DOOR.

FOR USE WITH FOUR HINGES4-1/2" (114.3) OR 5" (127)

*

4-7/8" (123.8)STRIKE

B

CL

46CURRIES Standard Hinge & Strike Locations for 1-3/8" FramesFRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


LSIZE A B C

6'8" (2032) 9-3/4" (247.7) 59-7/8" (1520.8) 10-3/8" (263.5)6'10" (2082.8) 9-3/4" (247.7) 61-7/8" (1571.6) 10-3/8" (263.5)7'0" (2133.6) 9-3/4" (247.7) 63-7/8" (1622.4) 10-3/8" (263.5)7'2" (2184.4) 9-3/4" (247.7) 65-7/8" (1673.2) 10-3/8" (263.5)

CL

CL

CL

A

B

C

40-5/16" (1023.9) STANDARD

HINGE BACKSET: 5/16" (7.9)

FOR USE WITH TWO HINGES 1-3/8" (34.9) DOOR3-1/2" (88.9) OR 4" (101.6)

STRIKE BACKSET 3/16" (4.8)

2-3/4" (69.9)

STRIKE

LLL

HINGE SIZE MAY VARY, LOCATION REMAINS THE SAME.CL

47CURRIES Standard Hinge & Strike Locations for 1-3/8" Frame



LL

SIZE A B C6'8" (2032) 9-3/4" (247.7) 29-15/16" (760.4) 10-3/8" (263.5)6'10" (2082.8) 9-3/4" (247.7) 30-15/16" (785.8) 10-3/8" (263.5)7'0" (2133.6) 9-3/4" (247.7) 31-15/16" (811.2) 10-3/8" (263.5)7'2" (2184.4) 9-3/4" (247.7) 32-15/16" (836.6) 10-3/8" (263.5)

CL

CL

CL CL

A

B

C

40-5/16" (1023.9) STANDARD


FOR USE WITH THREE HINGES 1-3/8" (34.9) DOOR3-1/2" (88.9) OR 4" (101.6)


2-3/4" (69.9)

STRIKE

LLL

B


48CURRIES Standard Hinge & Strike Locations for 1-3/4" Dutch FrameFRAME TECHNICAL DATANovember, 2004 ASSA ABLOY, the global leader


L

LSIZE A B C D E

6'8" (2032) 7-1/4" (184.2) 24-1/4" (616) 13-1/2" (342.9) 22-3/4" (577.9) 12-1/4" (311.2)6'10" (2082.8) 7-1/4" (184.2) 26-1/4" (666.6) 13-1/2" (342.9) 22-3/4" (577.9) 12-1/4" (311.2)7'0" (2133.6) 7-1/4" (184.2) 28-1/4" (717.6) 13-1/2" (342.9) 22-3/4" (577.9) 12-1/4" (311.2)7'2" (2184.4) 7-1/4" (184.2) 30-1/4" (768.4) 13-1/2" (342.9) 22-3/4" (577.9) 12-1/4" (311.2)7'10" (2387.6) 7-1/4" (184.2) 35-1/4" (895.4) 16-1/2" (419.1) 22-3/4" (577.9) 12-1/4" (311.2)8'0" (2438.4) 7-1/4" (184.2) 37-1/4" (946.2) 16-1/2" (419.1) 22-3/4" (577.9) 12-1/4" (311.2)9'0" (2743.2) 7-1/4" (184.2) 49-1/4" (1251) 16-1/2" (419.1) 22-3/4" (577.9) 12-1/4" (311.2)10”0" (3048) 7-1/4" (184.2) 61-1/4" (1555.8) 16-1/2" (419.1) 22-3/4" (577.9) 12-1/4" (311.2)

CL

CL

CL

CLCL

CL

A

B

E

35" (889) STANDARD


DUTCH DOOR4-1/2" (114.3) OR 5" (127)


4-7/8" (123.8)STRIKE

LLLL

D

C

50" (1270) STANDARD

SHELF HEIGHT IS42" (1066.8) STANDARD

NOTE:MAXIMUM FIRE LABELWIDTH: 3'8" (1117.6)

LLL


PLEASE INDICATE WHENADA COMPLIANCE ISREQUIRED. 48" CL IS NOTPRACTICAL WITH SOMEDEADLOCKS.

* *

49Frame Standard Rabbet Dimensions



L

DOUBLE RABBET

SINGLE RABBET

MULLION

2" (50.8)

5/8" (15.8)

VARIES

1/2" (12.7)

DOORTHICKNESS DIMENSIONS

1-3/8" 1-15/16" (49.2)1-3/4" 1-9/16" (39.7)

2"* 1-9/16" (39.7)2-1/4"* 1-9/16" (39.7)


1-3/8" 1-9/16" (39.7)1-3/4" 1-15/16" (49.2)

2"* 2-3/16" (55.5)2-1/4"* 2-7/16"

2" (50.8)

5/8" (15.8)

VARIES

1/2" (12.7)


1-3/8" 1-9/16" (39.7)1-3/4" 1-15/16" (49.2)

2"* 2-3/16" (55.5)2-1/4"* 2-7/16"

2" (50.8)

5/8" (15.8)

VARIES


1-3/8" 1-15/16" (49.2)1-3/4" 1-9/16" (39.7)

2"* 1-9/16" (39.7)2-1/4"* 1-9/16" (39.7)


1-3/8" 1-9/16" (39.7)1-3/4" 1-15/16" (49.2)

2"* 2-3/16" (55.5)2-1/4"* 2-7/16"

* NOT AVAILABLEKNOCKDOWN (KD)

504-1/2" Ultima Hinge ReinforcementFRAME TECHNICAL DATANovember 15, 2004 ASSA ABLOY, the global leader


L

TO REMOVE SHIM PLATE, INSERT FLAT SCREWDRIVER BETWEEN SHIMAND REINFORCEMENT, AND PRY SHIM AWAY FROM REINFORCEMENT.

NOTE: IF SHIM IS REMOVED, PRIME PAINT HINGE REINFORCEMENT.

DRILLED AND TAPPED PER HINGE TEMPLATE

PROJECTIONS FOR RESISTANCE WELDING

5-9/16" (141.3)

9" (228.6)

1-19/64" (32.9)

18 GA. (1.2) STEEL SHIM PLATE

7 GA. (4.5) STEEL

MUDCAP STANDARD ON “M” SERIES FRAME

OFFSET IN 16 GA. (1.4) FRAMEWITH SHIM PLATE .134" (3.4)WITHOUT SHIM PLATE .180 (4.6)

.134" (3.4) .180" (4.6)

515" Hinge Reinforcement



L

Heavy 5" Hinge Reinforcement

L

DRILLED AND TAPPED PERHINGE TEMPLATESTD. 12-24

PROJECTIONS FORRESISTANCE WELDING

5-9/16" (141.3)

9" (228.6)

7 GA. (4.5) STEEL

PROJECTIONS FORRESISTANCE WELDING

INDICATES HEAVY WEIGHT HINGE REINFORCEMENT

DRILLED AND TAPPED PERHINGE TEMPLATESTD. 12-24

NOTE: ELECTRICAL HINGE PREPARATIONAVAILABLE PER TEMPLATE

5-9/16" (141.3)

9" (228.6)

7 GA. (4.5) STEEL

1-5/8"(41.3)

1-5/8"(41.3)

52EH - Electric HingesFRAME TECHNICAL DATAJuly 1,2003 ASSA ABLOY, the global leader


SIZE AND LOCATIONPER TEMPLATE

PER TEMPLATE

PER TEMPLATE

53HFG Hinge Strap Reinforcement



L

ARC WELD AS SHOWN

7 GA. (4.5) X 1-29/32" (40.4) X 10" (254)HINGE REINFORCEMENT.DRILLED AND TAPPED FOR 12-24 UNC (STANDARD)(1/4-20 UNC OPTIONAL)

HOLE FOR ABUSE-RESISTANT STUD(OPTIONAL)

HIGH FREQUENCY HINGE REINFORCEMENT STRAPS12 GA. (2.6) REINFORCEMENT

COVERBOX

54Full Width Hinge ReinforcementFRAME TECHNICAL DATANovember, 2004 ASSA ABLOY, the global leader


L

ARC WELD FULL WIDTH ALONG EACH END IN RABBETS (ONLY WHEN SPECIFIED).STANDARD WELDS INDICATED WITH AT END.

7 GA. (4.5) X JAMB DEPTH MINUS 1/2" (12.7) X 10"(254) HINGE REINFORCEMENT.DRILLED AND TAPPED FOR 12-24 UNC (STANDARD)(1/4-20 UNC OPTIONAL)

HOLE FOR ABUSE-RESISTANT STUD(OPTIONAL)

COVERBOX

55Continuous Hinge Reinforcement

FRAME TECHNICAL DATASeptember 1, 2005ASSA ABLOY, the global leader


L

3/4" (19.1)

12 GA. (2.6)REINFORCING

1/4" (6.4)

1/4" (6.4)

3/4" (19.1)

12 GA. (2.6)REINFORCING

SURFACE MOUNTED TYPE CONCEALED MOUNTED TYPE

HGCF CODE

NOTE: HINGE MANUFACTURERS RECOMMEND REINFORCEMENTS ON 20, 18, 16 GAUGE FRAMES.

HGCR CODE

56Security Hinge and Grout GuardFRAME TECHNICAL DATANovember, 2004 ASSA ABLOY, the global leader


L

ARC WELD FULL WIDTH ALONG EACH END

PROJECTIONS FOR RESISTANCE WELDING

7 GA. (4.5) X 1-19/32" (40.4) X 9" (228.6)HINGE REINFORCEMENT.DRILLED AND TAPPED FOR 12-24 UNC (STANDARD)(1/4-20 UNC OPTIONAL)OFFSET PER HINGE THICKNESS

HOLE FOR ABUSE-RESISTANT STUDPER TEMPLATE AS REQUIRED.

16 GA. (1.4) COVERBOX SPOT WELDED OVER HINGE REINFORCING.

57Electric Hinge and Grout Guard



LARC WELD FULL WIDTH ALONG EACH END(OPTIONAL)

WELD PROJECTIONS FOR RESISTANCE WELDING

7 GA. (4.5) X 1-19/32" (40.4) X 9" (228.6)HINGE REINFORCEMENT.DRILLED AND TAPPED FOR 12-24 UNC (STANDARD)(1/4-20 UNC OPTIONAL)OFFSET PER HINGE THICKNESS

ELECTRICAL CONDUIT KNOCKOUT

16 GA. (1.4) GROUT GUARDCOVERBOX SPOT WELDEDOVER HINGE REINFORCING.

#8 PAN HEAD SCREWELECTRICAL HINGE WIREACCESS HOLE PER TEMPLATE.

NOTE: JUNCTION BOXES ARE NOT CAULKED AT THEFACTORY. TO BE FIELD CAULKED BY INSTALLATIONCONTRACTOR.

58HGA - Anchor Hinge Preparation FRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


L

7 GA. (4.5) HINGE REINF.

CURRIES DOES NOT DRILL AND TAPFOR HINGE SCREWS, UNLESS FRAME ISFACTORY WELDED AND PHYSICALSAMPLES ARE PROVIDED.

IF FRAME IS STICK OR KD THE PARTS ARESHIPPED LOOSE AND ARE NOT WELDEDTOGETHER, DRILL AND TAP IN FIELD.

ARC WELD

DOOR RABBET IS 1-15/16" (49.2)

59HGD - Hinge - Double ActingFRAME TECHNICAL DATA

April 1, 2002ASSA ABLOY, the global leaderin door opening solutions

L12 GA. (2.6)REINFORCING

.25 (6.4)

VERTICAL JAMB LINE

2.25 (57.2)

3.375(85.7)

NOMINALDOOR HEIGHT

60Pocket Pivot PreparationFRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


L

5/8" (15.9) STOP HEIGHTIF USING COVERBOX

7 GA. (4.5) REINF. TAB

PREPARATION:SIZE, DRILL AND TAP PER TEMPLATE

16 GA. (1.4) COVERBOX

PER TEMPLATE

PER TEMPLATE

NOTE: SOME POCKET PIVOTS REQUIRE FRAME FACE DIMENSIONS GREATER THAN 2" (50.8) - KD FRAMES NOT AVAILABLE OVER 2" FACE.

61SDL - Strike - Double Lip



L

PER TEMPLATE

PER TEMPLATE

12 GA. (2.6)REINFORCING TABS

NOTE: CONTACT FACTORY ONAVAILABILITY WHEN USEDWITH “C” TYPE COMPRESSIONANCHOR KD FRAMES.

62Rescue Hardware FrameFRAME TECHNICAL DATANovember, 2004 ASSA ABLOY, the global leader


L

12 GA. (2.6) REINFORCEMENT

PER TEMPLATE

PER TEMPLATE


DOUBLE LIP LATCH STRIKE12 GA. (2.6) REINFORCEMENT

COVERBOX

2" (50.8) MINIMUM FACE REQUIRED FOR COVERBOX

7-3/4"(196.9)

PERTEMPLATE

FLOORLINE

CL

CL

EMERGENCY STOP STRIKE SIDE

NOTE: CONTACT FACTORY ON AVAILABILITY WHEN USEDWITH “C” TYPE COMPRESSION ANCHOR KD FRAMES.

63Frame Pivots - Top, Bottom - Center Hung

FRAME TECHNICAL DATADecember, 2006ASSA ABLOY, the global leader


TOP PIVOT7 GA. (4.5) REINF.

COVERBOX

MUDCAP

MUDCAP

CENTER HUNGCASED OPENING

TOP AND BOTTOM DOUBLE ACTING PIVOT


BOTTOM PIVOT7 GA. (4.5) REINF.

TOP PIVOT7 GA. (4.5) REINF.1/8" INSET OR EDGE HUNG

COVERBOX

EDGE HUNGCASED OPENING

TOP AND BOTTOM SINGLE ACTING PIVOT



EDGE HUNGNOTE: NOT ALL BOTTOM PIVOTS REQUIRE A FRAME PREP.

64Frame Pivots - Top, Intermediate, Bottom - Single ActingFRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


L


INTERMEDIATE PIVOT7 GA. (4.5) REINF.

TOP PIVOT7 GA. (4.5) REINF.

COVERBOX

MUDCAP

65E1 Strike Reinf. (ANSI A115) 1-1/4" x 4-7/8"



L

E2 Strike Reinf. (ANSI A115) 1-1/8" x 2-3/4"

L

16 GA. (1.4) REINF.COVER BOX1-1/16" (27) DEEP

1-1/4" (31.8)

4-7/8"(123.8)

40" (1016) TO STANDARD ON 1-3/4" (44.5) DOOR

CL

STANDARD STRIKEBACKSET 5/16" (7.9)

SCREW HOLES ARE EXTRUDEDTO PROVIDE THREAD DEPTH

EQUAL TO 12 GA. (2.6) PLATE

16 GA. (1.4) REINF.COVER BOX1" (25.4) DEEP

1-1/8" (28.6)

2-3/4"(69.9)


40-5/16" TO STANDARD ON 1-3/8" DOOR

CL

STANDARD STRIKEBACKSET 3/8" (9.5)

1-3/4" DOORBACKSET 3/16"

1-3/8" DOOR



SIZE AND TAP PER ANSI 115.2

SIZE AND TAP PER ANSI 115.1 AND 115.2

CL

66E1B - Strike Reinf. - 1-1/4" x 4-7/8" - No LipFRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


L

4-7/8"(123.8)

1-1/4"(31.8)

40" (1016) TOSTANDARD ON 1-3/4" (44.5) DOOR

CL

12 GA. (2.6)REINF. TABS

PER TEMPLATE

67E3 Deadlock Strike Reinf. (ANSI/A115) 1-1/8" X 3-1/2"



L

E4 Deadlock Strike Reinf. (ANSI/A115) 1-1/8" x 2-3/4" No Lip

L

16 GA. (1.4) REINF. COVER BOX1-1/16" (27) DEEP

1-1/8" (28.6)

3-1/2"(88.9)


CL




16 GA. (1.4) REINF. COVER BOX1" (25.4) DEEP

1-1/8" (28.6)

2-3/4"(69.9)


CL





68EJ2 - Jamb Lock - 2" (50.8) FaceFRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


L

PERTEMPLATE

PERTEMPLATE

PERTEMPLATE

REINF. TABSPER TEMPLATE

PERTEMPLATE

2" (50.8) MIN. FACE3-1/16" (77.8) MIN. FACEON DRYWALL FRAME

40" (1016)

CL

69EJ4, EJ8, EJ12 - Jamb Lock



L

PERTEMPLATE

COVERPLATE

PERTEMPLATE

CUTOUTSPER

TEMPLATE

4" (101.6) STANDARD8" (203.2) STANDARD12" (304.8) STANDARD

STRIKE40" (1016)

CL

70E30 - Strike - Pocket LockFRAME TECHNICAL DATAJuly 1,2003 ASSA ABLOY, the global leader


L

PER TEMPLATE

PER TEMPLATE

7 GA. (4.5)REINF. TABS

40" (1016)

CL

71MAG - Magnetic Lock



L

PER TEMPLATE

PER TEMPLATE

REINF. TABSPER TEMPLATE

72E5 Rim Vertical Rod Surface Strike Reinf.FRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


L

G20 Vertical Rod Exit Mortise Strike Preparation

L

1-3/4" (44.5)

12 GA. (2.6)

10" (254)

CL

12 GA. (2.6) REINF. WELDEDTO INSIDE OF SOFFIT TIGHTTO DOOR RABBET STOP

G20 PREPARED FOR MORTISE STRIKES PERTEMPLATE OF HARDWARE MANUFACTURER

SPECIFY EXIT DEVICE AND STRIKE BEING USED WHEN ORDERING

E5 REINFORCING IS LOCATED ON CENTERLINE OF HEAD FOR PAIR FRAMESAND ADJACENT TO STRIKE JAMB ON SINGLE SWING FRAMES.

DOOR RABBET

HEADS

DOOR

73E8 Rim Exit Reinforcement



L

12 GA. (2.6)REINF. WELDEDTO INSIDE OFSOFFIT TIGHT TODOOR RABBETSTOP

41" (1041.4) TO STANDARD

CL

8" (203.2)

1-1/4" (31.8)*

12 GA. (2.6)

DOOR

* THE REINFORCEMENT WIDTH WILL BE EQUAL TO THE SOFFIT WIDTH WHEN LESSTHAN 1-1/4" (31.8). CUSTOMER SHOULD VERIFY HARDWARE COMPATIBILITYBEFORE ORDERING NARROW SOFFITS.

74E9 Electric StrikesFRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


L

NOTE: FIRE RATED FRAMES INCORPORATING AN ELECTRIC STRIKE WITH A COVERBOX, REQUIRE THAT THE WALL BOARD PENETRATE THE THROAT OF THE FRAME BY 1/2" (12.7) MINIMUM. ELECTRIC STRIKE MUST BE LISTED FOR USE WITH FIRE RATED OPENINGS.

16 GA. (1.4) REMOVABLECOVER BOX

CONFIGURATION OF CUTOUT VARIESPER HARDWARE MFG. TEMPLATE

SPECIFY STRIKE BEING USED WHEN ORDERING

STRIKECL

VERTICAL LOCATION OF ELECTRICSTRIKE WILL VARY WITH THE HARD-WARE MANUFACTURER, WHENORDERING FRAMES PREPARED FORAN ELECTRIC STRIKE, SPECIFY THETYPE OF LOCK BEING USED ALONGWITH CENTERLINE DIMENSIONREQUIRED OF THE LOCK.

7/8" (22.2) DIA.KNOCKOUT FOR ELECTRIC CONNECTOR


75Conduit - Coverbox Clearance Dimensions

FRAME TECHNICAL DATASeptember1, 2005ASSA ABLOY, the global leader


L1-1/8" (28.6) OR 7/8" (22.2) DIA.KNOCKOUT

RABBET CL

FACE

END VIEW OF FRAME AND COVERBOX

REMOVABLE COVER

AS REQUIRED

CL

CL

DEPTH

WIDTH

COVERBOX

1/2" (12.7) CONDUIT CONNECTOR LOCKNUTBY OTHERS1/2" (12.7) CONDUIT CONNECTOR

BY OTHERS

SIDE VIEW OF COVERBOX

LOCKNUT

1-1/8" (28.6)*

MINIMUM INSIDE DEPTH DIMENSION REQUIREDTO ACCOMODATE THE LOCKNUT.

* 1-1/2" (38.1) FOR 3/4" CONDUIT CONNECTOR

1/2" CONDUIT CONNECTORS ARE FOR 7/8” KNOCKOUT / 1-1/8” HIGH COVERBOX3/4" CONDUIT CONNECTORS ARE FOR 1-1/8" KNOCKOUT / 1-1/2" HIGH COVERBOX

DOUBLE KNOCKOUT FOR 1/2" AND 3/4"

CONDUIT CONNECTORS ARE FOR THE 1-1/2" HIGH COVER BOX ONLY

1-1/8" HIGH COVERBOX HAS 7/8" KNOCKOUTONLY FOR 1/2" CONDUIT CONNECTOR

1/2"(12.7)

3/4"(19.1)

76Conduit Preparation (RW-3)FRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


L

6.00" + 1.00"

TOP

JAMB MULLION

HEAD MULLION

LOCK SIDE

6.00" + 1.00"

1/2" STEEL FLEXIBLE CONDUITFACTORY INSTALLED WHEN REQUESTED(MULLION ONLY)

77E10 Standard Mtg. 14 ga. Closer Reinf.

FRAME TECHNICAL DATAJanuary 1, 2005ASSA ABLOY, the global leader


L

E11 Parallel Arm Mtg. 14 ga. Closer Reinf.

L

14 GA. (1.9)

1-3/4" (44.5)10" (254)

7" (177.8)

14 GA. (1.9)

1-1/4" (31.8)

20" (508)


DOOR

HINGE SIDE

HINGE SIDEDOOR

NOTE: WHEN SOFFIT WIDTH IS LESS THAN 1" - E16 WILL BE USED

78E12 Top Jamb Mtg. 14 ga. Closer Reinf.FRAME TECHNICAL DATANovember 15, 2004 ASSA ABLOY, the global leader


L

14 GA. (1.9)

2" (50.8)

16" (406.4)

1-3/4" (44.5)2-3/4" (69.9)

DOOR

HINGE SIDE

79E13 Corner Bkt. Mtg. 14 ga. Closer Reinf.

FRAME TECHNICAL DATAJanuary 1, 2005ASSA ABLOY, the global leader


L

Double Egress Frame Closer Reinforcements

L

14 GA. (1.9)

1-1/4" (31.8)

8" (203.2)

8" (203.2)


E11 ------------------PARALLEL ARM MOUNTING------------------14 GA. (1.9)20" (508) LONG

E10 ------------------REGULAR MOUNTING --------------------------14 GA. (1.9)10" (254) LONG

E12 ------------------TOP JAMB MOUNTING ------------------------14 GA. (1.9)16" (406.4) LONG

E17A ----------------FULL SLEEVE --------------------------------------14 GA. (1.9)REGULAR, TOP JAMB 16" (406.4) LONGPARALLEL ARM MOUNTINGS

E18 ------------------HALF SLEEVE --------------------------------------14 GA. (1.9)REGULAR AND 16" (406.4) LONGPARALLEL ARM MOUNTINGS

REGULARTOP

JAMB

DOOR

HINGE SIDE

80E15 Electric-Door Holder -Release/Closer 14 ga. Reinf.FRAME TECHNICAL DATANovember 15 , 2004 ASSA ABLOY, the global leader


L

E16 Double Parallel Arm 14 ga. Closer Reinf.

L

14 GA. (1.9)

*PER TEMPLATE

*PER TEMPLATE

14 GA. (1.9)

VARIES PER SOFFIT WIDTHUP TO 1-5/8" (41.3)

1-1/4" (31.8)

14 GA. (1.9) ADDITIONAL REINF. ADDEDWHEN SOFFIT IS UNDER 2" (50.8) IN WIDTH

20" (508)

20" (508)

14 GA. (1.9) ADDITIONAL REINF. WELDEDTO INSIDE OF SOFFIT TIGHT TO DOORRABBET STOP

DOOR

DOOR

* SPECIFY MANUFACTURER AND MODEL NUMBER WHEN ORDERINGADVISE POWER SOURCE LOCATION IF REQUIRED

HINGE SIDE

HINGE SIDE

81E17 14 Ga. Full Sleeve Closer Reinforcement

FRAME TECHNICAL DATANovember 15 ,2004ASSA ABLOY, the global leader


L

E18 14 ga. Formed Half Sleeve Closer Reinf.

L

14 GA. (1.9)

1-3/4" (44.5)

16" (406.4)

1" (25.4) MIN.

1-3/4" (44.5)

14 GA. (1.9)

2-3/8" (60.3)

1" (25.4) MIN.

1-3/4" (44.5)

HINGEJAMBLINE

16" (406.4)

NOTE: FULL SLEEVE CLOSER REINF. ARE BUILT TO MATCH FRAME PROFILES

16" (406.4)14 GA. (1.9)

1-3/4" (44.5)

1-3/8" (34.9) NOTE 13/4" (19.1) NOTE 2

5/8" (15.9)

1-15/16" (49.2) FOR 1-3/4" (44.5) DOOROR

1-9/16" (39.7) FOR 1-3/8" (34.9) DOOR

NOTE:1) 1-1/2" (38.1) MINIMUM SOFFIT REQ’D2) 1" (25.4) MINIMUM SOFFIT REQ’D

NOTE: HALF SLEEVE CLOSER REINF. ARE BUILT TO MATCH FRAME PROFILES

DOORHINGE SIDE

82EPT - Electronic Power TransferFRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


L

TOP HINGE

PER TEMPLATE

6" (152.4)*STANDARD

12 GA. (2.6)REINFORCINGTABS

PERTEMPLATE

PER TEMPLATE

* WOOD DOORS MAY REQUIRE OTHER LOCATION - CONTACT DOOR MANUFACTURER

83G21 - G22 Removable Hardware Mullion



L

H3A - H3B Surface Bolt Preparation

L

MULLION TOP BRACKET MOUNTING SCREWS TO BE DRILLED ANDTAPPED IN FIELD BY HARDWARE INSTALLER.

G21 PLATE REINFORCEMENTUSED WHEN SOFFIT IS 3" (76.2)WIDE OR GREATER.

G21

G22 PLATE REINFORCEMENTUSED WHEN SOFFIT IS LESS THAN3" (76.2).

G22

5/8" (15.9) C.R.S. FILLER BLOCK ISFURNISHED WHEN SOFFIT WIDTH IS TOONARROW TO APPLY HARDWARE TO SOFFIT

PLUG WELDED ONLY

WELDEDDOORDOOR HARDWARE MULLIONASSEMBLY

H3B-12 GA. (2.6)

H3A-12 GA. (2.6)

1-3/4" (44.5)

1-3/4" (44.5)

10" (254)

10" (254)

H3A FACE PREP.12 GA. (2.6) REINF. WELDEDTO INSIDE OF FRAME FACE

CLHEAD AND REINFORCEMENT

H3B SOFFIT PREP.12 GA. (2.6) REINF. WELDEDTO INSIDE OF SOFFIT TIGHT

TO DOOR RABBET STOP

NOTE: WHEN ORDERING SPECIFYEITHER H3A OR H3B REINFORCING

12 GA. (2.6)

DOOR

OF DOORS

DOOR SIDE

84G24 Coordinator ReinforcementFRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


L

12 GA. (2.6)

1-3/8" (34.9) 10" (254)

CL

12 GA. (2.6) REINF. WELDEDTO INSIDE OF FRAME FACE.

DOOR

OF DOORSCL

OF PAIR

2" (51)

85Grout Hole



L

RABBET PREPARATION(OPPOSITE DOOR RABBET STANDARD)

FACE PREPARATION(DOOR FACE STANDARD)

12 GA. (2.6) REINF. PLATE1-3/8" (35) DIA.HOLE IN REINF. PLATE

12 GA. (2.6) REINF. PLATE1-3/8" (35) DIA.HOLE IN REINF. PLATE

FILLER PLATESAME GAUGE AS FRAME.SHIPPED LOOSE.1-3/8" X 1-3/8"(35 X 35)

FILLER PLATESAME GAUGE AS FRAME.SHIPPED LOOSE.1-3/8" X 1-3/8"(35 X 35)

86H1 Flush Bolt ReinforcementFRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


L

H2 Flush Bolt Prep. and Reinf. (ANSI)

L

1-1/4" (31.8)12 GA. (2.6)

8" (203.2)

OF OPENING AND REINFORCEMENTCL

12 GA. (2.6) REINF. WELDED IN CENTER OF DOOR RABBETCL

12 GA. (2.6) 16 GA. (1.4) REINF. COVER BOX1-1/16" (27) DEEP

2-1/4" (57.2)

CL

CL

OF DOORS

CUTOUT

INACTIVE DOOR

13/16" (20.6)

15/16" (23.8)

15/32" (11.9) BACKSET


DOOR

DOOR

87H4 Auto Flush Bolt



L

H5 Non-handed Flush Bolt

L

PREPARATION FOR AUTOMATIC FLUSH BOLT IS PER HARDWARE MANUFACTURER’S TEMPLATE.

PLEASE SPECIFY MANUFACTURER AND MODEL NUMBER WHEN ORDERING.

LABELED IF HARDWARE IS APPROVED AND PREPPED TO TEMPLATE.

3-7/8" (98.4)

12 GA. (2.6) REINF.

15/16" (23.8)

OF DOORSCL

NOTE: STRIKE PLATE INSTALLEDFILLER PLATE MAY BE PURCHASEDSEPARATELY IN PACKAGES OF50 PIECES WITH SCREWS.

3-1/4" (82.6) 16 GA. (1.4) GALV. FILLER PLATEPART #CF004637

16 GA. (1.4) GALV. FILLER PLATEPART #CF001257

C' SUNK FOR #8-32 X 5/8" (15.9)FLAT HEAD HARDWARE SCREW

HEADCLCL

7/8" (22.2)

CL

5/8" (15.9)1-1/8" (28.6)

88Electric Magnetic Door Position SwitchFRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


L

16 GA. (1.4) GROUT GUARD COVERBOX ENDS SPOTWELDED OVER PREPARATION.

ELECTRICAL CONDUITKNOCKOUT AS REQUIRED.

#8 PAN HEAD SCREW.

CUTOUT SIZE AND LOCATIONPER HARDWARE TEMPLATE

12 GA. (2.6)REINFORCING TAB.

NOTE: JUNCTION BOXES ARE NOT CAULKED AT THE FACTORY. TO BE FIELDCAULKED BY INSTALLATION CONTRACTOR.

89Electric Fully-Concealed Door Position Switch



L

16 GA. (1.4) GROUT GUARD COVERBOX SPOTWELDED OVER PREPARATION.

ELECTRICAL CONDUITKNOCKOUT AS REQUIRED.

#8 PAN HEAD SCREW.

CUTOUT SIZE AND LOCATIONPER HARDWARE TEMPLATE

12 GA. (2.6)REINFORCING TAB.

NOTE: JUNCTION BOXES ARE NOT CAULKED AT THE FACTORY. TO BE FIELDCAULKED BY INSTALLATION CONTRACTOR.

90Cabinet Jamb FrameFRAME TECHNICAL DATAApril 1, 2002


L

DOOR OPENING

ROUGH OPENING

DOOR OPENING

ROUGH OPENING

NOT U.L. LISTEDS.M.W. JAMB SECTIONBUCKS SHIP LOOSE SQUARE BUTT ENDFIELD ASSEMBLED WITH SCREWSOR WELDED

1-3/4" (44.5)1" (25.4)

1-7/8" (47.6)

ROUGH OPENING DETERMINESTHE LENGTH OF THE BUCK LEGS

MACH SCREW#8 X 1/2" PAN HEAD

7/8" (22.2)

91Rough Buck Frame



L

2-1/2" (63.5) MIN.3" (76.2) MAX.

2-1/2" (63.5) MIN. TYP.3" (76.2) MAX. TYP.

DOOROPENING

ROUGHOPENING

DOOR OPENING

ROUGH OPENING

U.L. LISTED ROUGH BUCK FRAMESBUCKS SHIPPED LOOSE SQUARE BUTT END.FULLY PREPARED FOR INSTALLATIONWITH MOUNTING HOLES.

FINISH BUCK16 GA. (1.4) OR 14 GA. (1.9)

HINGE OR STRIKE REINF.1/4-20 NC X 1-1/4"FLAT HEAD MACH SCREW

2" (50.8)

2" (50.8)

#8 x 1/2"PAN HEADMACH SCREW

12 GA. (2.6) REINF. SUB-CHANNELU.L. FRAME ONLY

SUB-BUCK14 GA. (1.9) ONLY FOR LABEL

2" (50.8)

2" (50.8)

CORNER DETAILCORNER IS NOTCHED FOR FIELD INSTALLATIONFINISH BUCK CAN NOT BE WELDED PRIOR TOINSTALLATION.

NOTE: LABEL FRAMES FURNISHED WITH ATTACHING SCREWS AND BOLTS FOR ASSEMBLY

92Curriseal Frame Flush KD - WM - WGFRAME TECHNICAL DATASeptember, 2003 ASSA ABLOY, the global leader


L

K.D. “M” TYPE FLUSHGAUGE - 18 GA. (1.2), 16 GA. (2.4), 14 GA. (1.9)JAMB DEPTHS:

DOUBLE RABBET (WM) 5-1/4" (133.4) - 14" (355.6) (1/8" (3.2) INCREMENTS)SINGLE RABBET (WG) 4-1/8" (104.8) - 14" (355.6) (1/8" (3.2) INCREMENTS)

AVAILABLE WITH 4" (101.6) FACE HEADSDOUBLE RABBET AVAILABLE IN COMMUNICATING FRAMESWITH A 6-1/2" (165.1) MIN. JAMB DEPTH

HARDWARE RESTRICTIONSNOT RECOMMENDED- CLOSERS WITH REMOVABLE STOPS- VERTICAL ROD DEVICES WITH STRIKES MORTISED IN THE STOP- STOP ACTIVATED VERTICAL ROD DEVICES

NOTE: SOFFIT MOUNTED SURFACE HARDWARE MAY REQUIRE+_ 1/8" (3.2) ADJUSTMENT OF MOUNTING HOLES TO ACCOMODATEWEATHERSTRIP AND ENSURE NORMAL DOOR OPERATION.

CURRISEALACTUAL SIZE

COLOR: DARK BROWN

2-1/8"(54.0)

1-9/16" (39.7)

1-15/16" (49.2)ORVARIES

5/8" (15.9)ONLY

1" (25.4)1-1/4" (31.8)1-1/2" (38.1)1-3/4" (44.5)

2" (50.8)

1/2" (12.7)*

2-5/8" (66.7)ONLYWG

WM/WG

1-3/4" DOOR(44.5)

1/4" (6.3)

1/8" (3.2)

5-3/4" (146.1) JAMB DEPTH AVAILABLE WITH 7/16" (11.1) RETURNSTO PROVIDE A 4-7/8" (123.8) THROAT OPENING

CURRISEAL FRAME IS DESIGNED FOR USE WITH THE CURRISEAL ONLY

*KD CORNER

93Curriseal Frame KD Drywall - WC - WCG

FRAME TECHNICAL DATASeptember, 2003ASSA ABLOY, the global leader


L

K.D. “C” TYPE DRYWALLGAUGE - 18 GA. (1.2), 16 GA. (2.4), 14 GA. (1.9)JAMB DEPTHS:

DOUBLE RABBET (WC) 5-1/4" (133.4) - 14" (355.6) (1/8" (3.2) INCREMENTS)SINGLE RABBET (WCG) 4-1/8" (104.8) - 14" (355.6) (1/8" (3.2) INCREMENTS)

DOUBLE RABBET AVAILABLE IN COMMUNICATING FRAMESWITH A 6-1/2" (165.1) MIN. JAMB DEPTH

HARDWARE RESTRICTIONSNOT RECOMMENDED- CLOSERS WITH REMOVABLE STOPS- VERTICAL ROD DEVICES WITH STRIKES MORTISED IN THE STOP- STOP ACTIVATED VERTICAL ROD DEVICES

NOTE: SOFFIT MOUNTED SURFACE HARDWARE MAY REQUIRE+_ 1/8" (3.2) ADJUSTMENT OF MOUNTING HOLES TO ACCOMODATEWEATHERSTRIP AND ENSURE NORMAL DOOR OPERATION.

CURRISEALACTUAL SIZE

COLOR: DARK BROWN

2-1/8"(54.0)

1-9/16" (39.7)

1-15/16" (49.2)ORVARIES

5/8" (15.9)ONLY

1-1/2" (38.1)1-3/4" (44.5)

2" (50.8)

1/2" (12.7)

2-5/8" (66.7)ONLYWC/WCG

1-3/4" DOOR(44.5)

1/4" (6.3)

1/8" (3.2)

CURRISEAL FRAME IS DESIGNED FOR USE WITH THE CURRISEAL ONLY

KD CORNER

3/8" (9.5)

94NotesFRAME TECHNICAL DATAJanuary, 2007 ASSA ABLOY, the global leader


95Notes

FRAME TECHNICAL DATAJanurary, 2007ASSA ABLOY, the global leader


96Communicating FrameFRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


L

NOTE:U.L. AND W.H.I. LABELED FRAMES MAY BE PROVIDEDWITH COMPRESSION TYPE ANCHORING SYSTEM.

“M” PROFILE FLUSH K.D. “C” & “CM” PROFILE DRYWALL

EQUAL RABBET1-15/16" (49.2) FOR 1-3/4" (44.5) DOORS4-7/8" (117.5) THRU 14" (355.6) JAMB DEPTH

UNEQUAL RABBET1-15/16" (49.2) X 1-9/16" (39.7) FOR1-3/4" (44.5) X 1-3/8" (34.9) DOORS4-1/2" (114.3) THRU 14" (355.6) JAMB DEPTH



UNEQUAL RABBET1-15/16" (49.2) X 1-9/16" (39.7) FOR1-3/4" (44.5) X 1-3/8" (34.9) DOORS4-1/2" (114.3) THRU 14" (355.6) JAMB DEPTH


97Pocket Door Frame - Standard 1-3/8" or 1-3/4" Door Single

FRAME TECHNICAL DATAJune, 2006 ASSA ABLOY, the global leader


L

2"(50.8)

2" (50.8)FINISH OPENING

**

1

32

NOMINALDOOR

OPENING HEIGHT

*

2" (50.8)

NOMINALDOOR

OPENING HEIGHT

*

5/8" (15.9)

5/8" (15.9)

DOOR

1

VERIFY HARDWARE ADAPTABILITYFRAME MUST BE INSTALLED AND

HARDWARE TRACK MUST BE HUNGPRIOR TO FINISH WALL STUDS BEING SET.

AVAILABLE IN 18 GA. (1.2) AND 16 GA.(1.4) STEEL.

2" (50.8)

2" (50.8)FINISH OPENING WIDTH

**1/2" (12.7)

1/2" (12.7)

2

5/8" (15.9)

2" POCKET(50.8)

1-3/4" (44.5) DOOR 3

NOTE: 1-3/8" (34.9) DOORFRAME HAS 1-5/8" (41.3) POCKET

EQUAL

EQUAL

1" (25.4)DOOR

POCKET

1/2" (12.7)

1/2" (12.7)

4" (101.6) MIN.12" (304.8) MAX.

ANCHORSUSED FOR METAL STUDOR WOOD STUD WALL

1" (25.4)

4-1/4" (107.9)

VARIES WITH JAMB DEPTH & STUD SIZE.SPECIFY STUD SIZE WHEN ORDERING.

FINISH OPENING WIDTH IS 1" (25.4) LESSTHAN A STANDARD OPENING WIDTH.EXAMPLE: A 3'0" (914.4) POCKET FRAME WILLHAVE FINISH OPENING WIDTH OF 2'11" (889).THIS ALLOWS THE USE OF STANDARD DOOR WIDTHS.

FINISH OPENING HEIGHT IS NOMINAL DOOR HEIGHTUSING CURRIES STANDARD DOOR UNDERCUT.

**

*

TRACK HARDWARE &REINFORCEMENT

PROVIDED BY OTHERS

98Pocket Door Frame-Saw Mitered-Welded for 1-3/4" or 1-3/8" DoorsFRAME TECHNICAL DATAJune, 2006 ASSA ABLOY, the global leader


L

1. MITER HEAD AND JAMB AT 45˚2. CLAMP AND TACK WELD AT BACKBEND AND FACE.3. CONTINUOUS WELD INSIDE SEAM.4. GRIND AND FINISH OUTSIDE SURFACES.

SPLIT HEAD AND HINGE JAMB

A

B

C

A

B

C

STRIKE JAMB

FLOOR ANCHOR

99Stainless Steel Slip-On Type Spats



L

STAINLESS STEEL SLIP-ON SPATSTANDARD PROFILE IS MANUFACTUREDTO FIT OVER JAMB PROFILE.SPECIFY JAMB PROFILE WHEN ORDERING

20 GA. (.91) #304 STAINLESS STEEL#4 SATIN GRAIN FINISH

NOTE:SPATS ARE LABELED UP TOA HEIGHT OF 8" (203.2)

4" (101.6)STANDARD

4" (101.6)STANDARD

HOSPITAL TYPE SPATSTANDARD PROFILE IS MANUFACTURED

TO FIT OVER JAMB BELOW STOP.SPECIFY JAMB PROFILE WHEN ORDERING

20 GA. (.91) #304 STAINLESS STEEL#4 SATIN GRAIN FINISH

NOTE:HOSPITAL TYPE SPATS

ARE LABELED UP TOA HEIGHT OF 6" (152.4)

100Hospital StopFRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


L

ANCHOR PART NUMBER: P0079FILLER & BACKING PLATEUSED ON FRAMES NOT REQUIRING A FOOT CLIP ORFRAMES THAT HAVE SOME OTHER BASE ANCHORING METHOD.

ANCHOR PART NUMBER: P0077FILLER & COMBINATION BACKING PLATE-FOOT CLIPUSED ON FRAMES REQUIRING A FOOT CLIP.

NOTE: FOOTCLIP REQUIREDFOR LABEL

VARIES

STOP CUT AWAY ON 45˚ ANGLE TO RECEIVE FILLER

4" (101.6)STANDARD

FILLER SIZES AVAILABLEUP TO 9" (228.6) HIGH

CHOOSE EITHER P0077 OR P0079BACKING PLATE.WELD BACKING PLATE BEHINDCUTOUT.WELD FILLER INTO CUTOUT, GRIND,FILL AND FINISH SMOOTH.

4" (101.6) STANDARDFROM FACTORY

*

HEIGHTS AVAILABLE UP TO 9" (228.6) HIGH6" (152.4) HIGH MAXIMUM ON FIRE RATED FRAMESFACTORY INSTALLED OR BY SECOND LOCATION SHOP

*

45˚ CUT

101Thermal Break Frame KD Flush Profile



L

14 GA. (1.9) AND 16 GA. (1.4) GALVANEALED STEEL

#8 X 1/2" (12.7) PAN HEAD S.M.S.

2" (50.8) OR 4" (101.6) FACE HEAD

DOOR RABBET

5-1/2" (139.7)THRU 10-3/4" (273.1)

JAMB DEPTH

2" (50.8) FACE

STEEL POP RIVETS IN PAIRSON 12" (305) CENTERS MAXIMUM

CLOSED CELL POLYETHYLENE FOAM

DOOR RABBET

THERMAL BREAK FRAME PROVIDES A 57% REDUCTION IN THERMAL CONDUCTIVITY.PUNCH FOR SILENCERS NOT AVAILABLE.

102Thermal Break Frame CCW Stick ComponentsFRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


L

16 GA. (1.4) AND 14 GA. (1.9) GALVANEALED STEEL ONLY5/8" (15.9) HIGH STOPS ONLY BUTT END JOINTS ONLYNOT LABELED

5-1/2" (139.7)THRU 10-3/4" (273.1)

JAMB DEPTH

2" (50.8) OR 4" (101.6) FACE

DO

OR

RA

BB

ET

DO

OR

RA

BB

ET CLOSED CELL POLYETHYLENE FOAM

STEEL POP RIVETS ON 12" (305) CENTERS MAXIMUM

MULLION - 16 GA. (1.4) AND 14 GA. (1.9) 2" (50.8) FACE ONLY.PUNCH FOR SILENCERS NOT AVAILABLE.

2" MAX.(50.8)

103CCW - Drip Cap CCW 112 - 10'6-5/8" Lengths



L

Mullion Construction

L

10'6-5/8" (3216.3)

1" (25.4)

3/4" (19)

45˚DRIP CAP

C.C.W. 112

16 GA. (1.4) GALVANEAL

104Removable Vertical Mullion / BracketFRAME TECHNICAL DATAAugust 20, 2003 ASSA ABLOY, the global leader


L

MULLION BRACKET IS USED AT THE TOP AND BOTTOM OF FRAME

ATTACH MULLION BRACKET TO FRAME

NOTCH MULLION FACE TO ALLOW DIMENSION “D” TO PASS THRU.

SLIDE MULLION IN PLACE

DIM. “B” = JAMB DEPTH - FRAME GAUGE THICKNESSDIM. “D” = DETERMINED BY FACE DIMENSION

*

*

EQUAL TO FACE DIM. MINUS 1/4" (6.4)

2"(50.8)

1" (25.4)

“D”

ARC WELD2 PLACES MINIMUM

DIM “B”

DRILL 3/16" (4.8)2 HOLES

12-24 TAPSCREWS

INSTALLED

*


NOTE: THE MULLION WILL BE REMOVABLE FROM THE FACE OPPOSITE THE DOOR RABBET.

105Removable Horizontal Mullion / Bracket



L

ATTACH MULLION BRACKET TO FRAME

NOTCH MULLION FACE TO ALLOWDIMENSION “D” TO PASS THRU.

SLIDE MULLION IN PLACE

DIM. “B” = JAMB DEPTH - FRAME GAUGE THICKNESSDIM. “D” = DETERMINED BY FACE DIMENSION

*

*

*

2 HOLES 3/16" (4.8)12-24 TAP PAN HEAD 1/2"SCREWS INSTALLED

“D”

1" (25.4)2"

(50.8)

EQUAL TO FACE DIM. MINUS 1/4" (6.4)

SPOT WELD2 PLACES MINIMUM

DIM “B”

12 GA. (2.6)


NOTE: INDICATE APPROPRIATE HAND OF ELEVATION AND WHICH SIDE OF ELEVATION MULLIONSHOULD BE REMOVABLE FROM.

106Splice Connection Head or JambFRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


L

Field Splice Connection with Bracket

L

1. FIT SPLICING SLEEVE REINF. HALFWAY INTO ONE SIDE AND TACK WELD IN PLACE.2. SLIP OTHER SIDE OVER SPLICING SLEEVE REINF. AND ALIGN SEAMS FOR STRAIGHTNESS.3. TACK WELD SPLICING SLEEVE REINF. INSIDE AND TACK WELD OUTSIDE SEAM AT BOTH FACES.4. CONTINUOUS WELD SEAM - GRIND AND FINISH SMOOTH.

12" (304.8)

12 GA. (1.9) SPLICING REINF.


12 GA. (2.6)FIELD SPLICING SLEEVE

ARC WELD INSIDE

ARC WELD INSIDE

FIELD SPLICE WITH BRACKETFIELD WELD & FASTEN WITH SCREWS

3" (76.2)


NOTES FOR LABELING PURPOSES:1) NOTCH SOFFIT OF ADJOINING PIECE.2) ARC WELD SPLICING SLEEVE BRACKET TO MULLION.3) FULL WELD FACES OF BOTH PIECES TOGETHER, OR

ATTACH WITH 3 #10 SCREWS THROUGH FACE INTO FIELD SPLICING SLEEVE BRACKET.

107KD Double Egress Frame Standards

FRAME TECHNICAL DATAOctober, 2007ASSA ABLOY, the global leader


LHANDING

LHRRH LH

RHR

DOUBLE RIGHT HAND SWING(STANDARD)

2

1

3 MEETING EDGE

5-3/4" (146.1) JAMB DEPTH HAS 7/16" (11.1) RETURN 18, 16, 14 GA.12 GA. 1/2" RETURN NO KD

2-5/8"(79.4)

4-3/4" (120.7) MIN.14" (355.6) MAX.

EQUAL

1-15/16"(49.2)

EQUAL

THROATOPENING

*1/2" (12.7)

*1/2" (12.7)

2" (50.8)

1-3/8" (34.9) 5/8" (15.9)

FINISHOPENINGWIDTH

1 JAMB

2 HEAD

THROATOPENING

1/2"(12.7)

1/2"(12.7)

2-5/8"(79.4)

4" (101.6) MIN.14" (355.6) MAX.

2"(50.8)

5/8" (15.9)

* *

*

M - FLUSH SERIES KDC - DRYWALL KD NOT AVAILABLE

3

3/32" (.094) CL HEAD

3/16" (.188)

SOFFIT STOP IS HELD BACK 3/32" TOPROVIDE PROPER DOOR CLEARANCE

108Lead Line ClipFRAME TECHNICAL DATANovember, 2004 ASSA ABLOY, the global leader


L

S.B.E. Double Egress Frame Corner Joints

L

1" (25.4)

1" (25.4)

1/2"(12.7)

16 GA. (1.4)

DOOR RABBET

16"(406.4)

CL

CL

STEEL CLIP IS BENT OVER TO RETAINLEAD LINING

DOOR RABBET

1-1/8" (28.6) MIN.

RETURN FILLER

RETURN FILLER

WELD

RETURN FILLER

VERTICAL BUTT JOINT(STANDARD)WELDED &GROUND SMOOTH

HORIZONTAL BUTTJOINT(OPTIONAL)WELDED &GROUND SMOOTH

109CCW - Open Back Rail - 10'6-5/8" Lengths



L

6'8" (2032) LOCATION 3 HINGES C.C.W. 247'0" (2133.6) LOCATION 3 HINGES C.C.W. 257'2" (2184.4) LOCATION 3 HINGES C.C.W. 39

OPEN BACK RAILHINGE JAMB

7'10" (2387.6) LOCATION 4 HINGES C.C.W. 628'0" (2438.4) LOCATION 4 HINGES C.C.W. 639'0" (2743.2) LOCATION 4 HINGES C.C.W. 11910'0" (3048) LOCATION 4 HINGES C.C.W. 120

OPEN BACK RAILHINGE JAMB

FOR 1-3/4" (44.5) DOORS ALL STRIKE LOCATIONS 40" (1016)IF PUNCHED - SILENCERS ARE REQUIREDWHEN ORDERING CCW 26 STRIKE JAMB SPECIFY DOOR HEIGHT

OPEN BACK RAILSTRIKE JAMB

CL

NOTE: ANCHORS ARE NOT INCLUDED WITH CCW MATERIAL.CCW MATERIAL MAY BE ORDERED CUT TO LENGTH - EXACT LENGTH - WITHS.M.O. OR S.B.E. CORNER CONFIGURATION.CUSTOM PROFILES AVAILABLE.12 GA. FRAMES ARE CCW. 5-3/4 JAMB DEPTH HAS 1/2" RETURNS.

C.C.W. 26

10'6-5/8" (3216.3)

110CCW - Mullion Closed Section - 10'6-5/8" Lengths FRAME TECHNICAL DATANovember, 2004 ASSA ABLOY, the global leader


L

6'8" (2032) LOCATION 3 HINGES C.C.W. 427'0" (2133.6) LOCATION 3 HINGES C.C.W. 437'2" (2184.4) LOCATION 3 HINGES C.C.W. 44

MULLION - CLOSED SECTIONHINGE JAMB

7'10" (2387.6) LOCATION 4 HINGES C.C.W. 818'0" (2438.4) LOCATION 4 HINGES C.C.W. 829'0" (2743.2) LOCATION 4 HINGES C.C.W. 13310'0" (3048) LOCATION 4 HINGES C.C.W. 134

MULLION -CLOSED SECTIONHINGE JAMB

FOR 1-3/4" (44.5) DOORS ALL STRIKE LOCATIONS 40" (1016)IF PUNCHED - SILENCERS ARE REQUIREDWHEN ORDERING CCW 41 STRIKE JAMB SPECIFY DOOR HEIGHT

MULLION -CLOSED SECTIONSTRIKE JAMB

CL

C.C.W. 41

10'6-5/8" (3216.3)

12 GA. FRAMES ARE CCW

111CCW - Mullion Closed Section - 10'6-5/8" Lengths Communicating Mullion



L

10'6-5/8" (3216.3)

MULLION - CLOSED SECTIONCOMBINATION RAILALL STANDARDDOOR HEIGHTS.

DOUBLE HINGE, DOUBLESTRIKE OR HINGE ANDSTRIKE COMBINATIONS.

6'8" (2032) LOCATION 3 HINGES & STRIKE C.C.W. 457'0" (2133.6) LOCATION 3 HINGES & STRIKE C.C.W. 467'2" (2184.4) LOCATION 3 HINGES & STRIKE C.C.W. 477'10" (2387.6) LOCATION 4 HINGES & STRIKE C.C.W. 838'0" (2438.4) LOCATION 4 HINGES & STRIKE C.C.W. 849'0" (2743.2) LOCATION 4 HINGES & STRIKE C.C.W. 13510'0" (3048) LOCATION OF 4 HINGES & STRIKE C.C.W. 136DOUBLE STRIKE MULLION C.C.W. 85NOTE: WHEN ORDERING CCW 85 SPECIFY DOOR HEIGHT.6'8" (2032) LOCATION 3 (DOUBLE HINGES) C.C.W. 867'0" (2133.6) LOCATION 3 (DOUBLE HINGES) C.C.W. 877'2" (2184.4) LOCATION 3 (DOUBLE HINGES) C.C.W. 887'10" (2387.6) LOCATION 4 (DOUBLE HINGES) C.C.W. 898'0" (2438.4) LOCATION 4 (DOUBLE HINGES) C.C.W. 909'0" (2743.2) LOCATION 4 (DOUBLE HINGES) C.C.W. 13710'0" (3048) LOCATION OF 4 (DOUBLE HINGES) C.C.W. 138

NOTE: WHEN ORDERING COMBINATION MULLION DOUBLE HINGE, DOUBLE STRIKE, OR HINGE AND STRIKE, PROVIDE SECTION DETAIL OF DOOR RABBETLOCATION.

EXAMPLE

12 GAUGE FRAMES ARE CCW

112CCW Sills - CCW 28, 139, 140, 48, 49, 55 - 10'6-5/8" LengthsFRAME TECHNICAL DATANovember, 2004 ASSA ABLOY, the global leader


L

4" (101.6)6" (152.4)8" (203.2)

JAMBDEPTH

FULL JAMB DEPTH 4" (101.6) FACE OR LESS C.C.W. 28FULL JAMB DEPTH 6" (152.4) FACE OR LESS C.C.W. 139FULL JAMB DEPTH 8" (203.2) FACE OR LESS C.C.W. 140

6-13/16" (173)

JAMBDEPTH

FULL JAMB DEPTH 6-13/16" (173) FACE C.C.W. 55

4" (101.6)6" (152.4)8" (203.2)

5/8" (15.9)

1-9/16" (39.7)

SPECIAL 1-9/16" (39.7) THICK C.C.W. 48

4" (101.6)6" (152.4)8" (203.2)

5/8" (15.9)

1-15/16" (49.2)

SPECIAL 1-15/16" (49.2) THICK C.C.W. 49

10'6-5/8" (3216.3)


113CCW - Plain Mullion CCW 16, 17, 18, 50 - 10'6-5/8" Lengths



L

10'6-5/8" (3216.3) 2" (50.8) FACE

JAMB DEPTH

PLAIN MULLION 2" (50.8) FACE C.C.W. 16

4" (101.6) FACE

JAMB DEPTH


6" (152.4) FACE

JAMB DEPTH


8" (203.2) FACE

JAMB DEPTH



114CCW - Plain Rail CCW 21, 23, 115, 117 - 10'6-5/8" LengthsFRAME TECHNICAL DATANovember, 2004 ASSA ABLOY, the global leader


L

10'6-5/8" (3216.3)2" (50.8) FACE

JAMB DEPTH

PLAIN RAIL 2" (50.8) FACE C.C.W. 21

JAMB DEPTH


JAMB DEPTH


4" (101.6) FACE

6" (152.4) FACE

JAMB DEPTH


8" (203.2) FACE


115Sill Reinforcement

FRAME TECHNICAL DATAAugust, 2003ASSA ABLOY, the global leader


LANCHOR PART NUMBER: P320

LOCATED EVERY 18" OF SILL LENGTH WHEN FACE EXCEEDS 5".PROVIDES ADDITIONAL SUPPORT TO PROFILE FACE.

2" (50.8)

1-1/2" (38.1)

12 GA. (2.6)

ONE STIFFENER EVERY 18" OFLENGTH ON FACE DIMENSIONS5" TO 9" FACE DIMENSIONS 9"THRU 16" MAX. REQUIRE TWOSTIFFENERS PER 18" OF LENGTH.

116CCW - Misc. Rail CCW 19, 27, 22, 29 - 10'6-5/8" LengthsFRAME TECHNICAL DATANovember, 2004 ASSA ABLOY, the global leader


L

JAMB DEPTH

COVER PLATECORNER OR FLAT

10'6-5/8" (3216.3)

C.C.W. 19

FILLER PLATE WITHOUT STOP

C.C.W. 27

FILLER PLATE WITH STOP

C.C.W. 22

HEAD CAP

C.C.W. 29

JAMB DEPTH

JAMB DEPTH

JAMB DEPTH

OR

CORNER

FLAT


117CCW - Misc. Rail CCW 91, 92, 40 - 10'6-5/8" Lengths



L

10'6-5/8" (3216.3)

JAMB DEPTH

JAMB DEPTH

JAMB DEPTH

CHANNEL HEAD REINF.

C.C.W. 91

FULL WIDTH HEAD REINF.

C.C.W. 92

CASED OPENING PLAIN RAILCASED OPENING PLAIN RAIL 4" (101.6)

C.C.W. 40 2" FACEC.C.W. 20 4" FACE


118CCW - Corners CCW 51, 52, 53, 54, 10'6-5/8"FRAME TECHNICAL DATANovember, 2004 ASSA ABLOY, the global leader


L

JAMB DEPTH

1-15/16"(49.2)

1-9/16"(39.7)

2 WAY CORNER1-9/16" (39.7) OUTSIDE

C.C.W. 51

JAMB DEPTH

1-15/16"(49.2)

1-9/16"(39.7)

JAMB DEPTH

1-15/16"(49.2)

1-9/16"(39.7)


C.C.W. 52

JAMB DEPTH

1-15/16"(49.2)

1-9/16"(39.7)

JAMB DEPTH

1-15/16"(49.2)

1-9/16"(39.7)


C.C.W. 53

JAMB DEPTH

1-15/16"(49.2)

1-9/16"(39.7)

1-15/16"(49.2)

1-9/16"(39.7)

JAMB DEPTH

1-15/16"(49.2)

1-9/16"(39.7)


C.C.W. 54

JAMB DEPTH

1-15/16"(49.2)

1-9/16"(39.7)

1-15/16"(49.2)

1-9/16"(39.7)


119CCW - Glass Stop



L

CCW# HEIGHT X WIDTH DESCRIPTION93 5/8" (15.9) X 5/8" (15.9) PRIME PAINT - PUNCHED 12" (304.8) ON CENTER97 5/8" (15.9) X 5/8" (15.9) PRIME PAINT - BLANK101 5/8" (15.9) X 5/8" (15.9) NO PAINT - BLANK105 5/8" (15.9) X 5/8" (15.9) NO PAINT - PUNCHED 12" (304.8) ON CENTER

94 5/8" (15.9) X 1" (25.4) PRIME PAINT - PUNCHED 12" (304.8) ON CENTER98 5/8" (15.9) X 1" (25.4) PRIME PAINT - BLANK102 5/8" (15.9) X 1" (25.4) NO PAINT - BLANK106 5/8" (15.9) X 1" (25.4) NO PAINT - PUNCHED 12" (304.8) ON CENTER

95 3/4" (19) x 5/8" (15.9) PRIME PAINT - PUNCHED 12" (304.8) ON CENTER99 3/4" (19) x 5/8" (15.9) PRIME PAINT - BLANK103 3/4" (19) x 5/8" (15.9) NO PAINT - BLANK107 3/4" (19) x 5/8" (15.9) NO PAINT - PUNCHED 12" (304.8) ON CENTER

96 3/4" (19) X 1" (25.4) PRIME PAINT PUNCHED 6" (152.4) ON CENTER100 3/4" (19) X 1" (25.4) PRIME PAINT - BLANK104 3/4" (19) X 1" (25.4) NO PAINT - BLANK108 3/4" (19) X 1" (25.4) NO PAINT - PUNCHED 6" (152.4) ON CENTER

143 1" (25.4) X 1" (25.4) - PRIME PAINT - PUNCHED 6" (152.4) ON CENTER

GLASS STOP IS MANUFACTURED FROM GALVANEALED STEEL. PAINT IS CURRIES STANDARD GRAY PRIME. PUNCHING IS FOR OVAL HEAD SCREWS SIZE #8.

NOTE: HOLE PUNCHING ON GLASS STOP IS STANDARD 12" (304.8) ON CENTER. IF STOP IS TO BE USED FOR LABEL FRAME APPLICATIONS YOU MUST SPECIFY ON ORDER THAT HOLES ARE TO BE 6" (152.4) ON CENTER.

ALL GLASS STOP AND SOFFIT STOP MATERIAL COME IN 10'6" (3200.4) LENGTHS

STAINLESS STEEL GLASS STOP IS 16 GA. (1.4)

5/8"(15.9)

5/8"(15.9)

5/8"(15.9)

1"(25.4)

3/4"(19)

5/8"(15.9)

3/4"(19)

1"(25.4)

1"(25.4)

1"(25.4)

9/32" (7.1)

16 GA.

16 GA.

16 GA.

18 GA.

18 GA.

120CCW - Shipping Spreader Bar CCW 111 - 10'6-5/8"FRAME TECHNICAL DATAApril 1, 2002 ASSA ABLOY, the global leader


L

TACK WELD SHIPPING SPREADER BAR TO BOTTOM OFFRAME RABBET INSIDE NOMINAL FRAME OPENING.

TOP VIEW LOOKING DOWN

3/8" (9.5)

1" (25.4)

NOTE: CURRIES HOLLOW METAL FRAMES HAVE DOUBLE SHIPPING SPREADERBARS WELDED ON THE BOTTOM. THE SPREADER BARS MUST BE REMOVED AND ASETTING SPREADER USED FOR FINAL INSTALLATION. A COLD CHISEL AND HAMMER ARE RECOMMENDED TOOLS TO USE TO REMOVE THESE. THE FRAMEINSTALLER ASSUMES ALL RESPONSIBILITY FOR PLUMB FRAME INSTALLATION.

121Custom Frame Profiles

FRAME TECHNICAL DATAOctober, 2003ASSA ABLOY, the global leader


LCONTACT FACTORY FOR CAPABILITIES

3/4" (19.1)MINIMUM

1" (25.4)MINIMUM

3/8" (9.5)MINIMUM

289 3/4" (19.1)MINIMUM

1" (25.4)MINIMUM

1/2" (12.7)MINIMUM

B

3/8" (9.5)MINIMUM

VARIES

VARIES

1/8" (3.2) 16 GA. (1.4)MINIMUM

F

5/32" (4) 14 GA. (1.9)MINIMUM

NOTE: FOR 12 GA. (2.6) CONTACT FACTORY

122Custom Frame ProfilesFRAME TECHNICAL DATAJuly 1, 2003 ASSA ABLOY, the global leader


L

3/4" (19.1)MINIMUM

1-1/2" (38.1)MINIMUM

2" (50.8)MAXIMUM

H

JAMBDEPTH

1/2" (12.7)MINIMUM

NOTE THROAT OPENINGWHEN ORDERING

1/2" (12.7) RADIUS ONLY

1/2" (12.7)

3/4" (19.1)MINIMUM

1" (25.4)MINIMUM

2" (50.8)MAXIMUM

L

1/2" (12.7)MINIMUM

1/2" (12.7)

3/8" (9.5)MINIMUM

3/4" (19.1)MINIMUM

1" (25.4)MINIMUM

1/8" (3.2) 16 GA. (1.4)3/16" (4.8) 14 GA. (1.9)

I

NOT 12 GA. (2.6)

16 GA. ONLY

1/2" (12.7)ONLY

1/2" RADIUS

1/4" (6.4)ONLY

275

16 GA. ONLY3-1/2" MIN. (88.9)14" MAX. (355.6)

123Notes

FRAME TECHNICAL DATAAugust, 2006ASSA ABLOY, the global leader


124NotesFRAME TECHNICAL DATAAugust, 2006 ASSA ABLOY, the global leader


125StormPro® 361 Frame Construction

FRAME TECHNICAL DATAMay, 2007

L


SINGLE

A

B

B

B

A

C

DOUBLE

2" (50.8)or 4" (101.6)

1/2" (12.7)1/2" (12.7)

2" (50.8)

5-3/4"(146)

OUTSWINGONLY

OUTSWING

ONLY

OU

TSWIN

G

ON

LY

2" (50.8)

1/2" (12.7)1/2" (12.7)

FRAMES ARE 16 GAUGE (1.4) A60, KD ORFACE WELDED CORNER CONSTRUCTION

SARGENT HC980 MULLION REQUIRED ONPAIRS OF DOORS

B

BA

5-3/4" (146) MIN.14" (355.6) MAX.

5-3/4" (146) MIN.14" (355.6) MAX.

FRAMES MUST BE INSTALLED ANDANCHORED PER SHOP DRAWINGS.WALLS CONSTRUCTED AS DESCRIBED INFEMA 361 (DESIGN AND CONSTRUCTIONGUIDANCE FOR COMMUNITY SHELTER)

126Steel Channel Anchor Installation - Drywall Return FrameFRAME TECHNICAL DATAAugust 1, 2002

L


TWIST 45˚ TOCLEAR THE RETURNS.

TWIST THE ANCHORUPRIGHT.

ROTATE THEANCHOR CLOCKWISE TOTIGHTEN IN THEPROFILE.

ROTATE TO GET THEANCHOR LEGSUNDER THE PROFILE RETURNS.

ROTATE ANCHOR 45˚TO CLEAR RETURNS.SLIDE INTO PROFILE.

ANCHOR PART NUMBER: PO149

127Door Silencers

FRAME TECHNICAL DATAOctober 1, 2002ASSA ABLOY, the global leader


TOP OFSTRIKE

CUTOUT

SILENCERS

8" (203.2)

10" (254)

2" (50.8)

SINGLE DOORFRAME

SILENCERS

CL

5" (127)

5" (127)

PAIR OF DOORS FRAME

ADHESIVE TYPE

ADHESIVE BACKED SILENCERSFIELD APPLIED AFTER FINISH PAINTING

PUNCH TYPE

17/64" (6.8) DIA. HOLETO ACCEPT PUSH IN

TYPE SILENCERS

17/64" (6.8) 5/8" (15.9)

ADHESIVEBACKING

128Loose Spline SleeveFRAME TECHNICAL DATASeptember, 2003 ASSA ABLOY, the global leader


JAMB DEPTH-5/16" (7.9)

4" (101.6)

PART #P20016 (1.4) GA.

4 SPOTWELDS

16 GA. (1.4)

PART #P200

L

129Recommended Erection Instructions



NOTE: Shipping bars should not be used asspreader. Remove shipping bar before settingframe.

Plumbing the frameThe contractor should be equipped with a car-penter level, square and spreader. Set the framein desired location and level the header. Squarejambs to header. Shim under jambs if necessary.With frame on line, set spreader and fastenjambs to floor through floor anchors.

BR

AC

ING

FRA

ME

SB

EFO

RE

WA

LLC

ON

STR

UC

TIO

NN

EW

MA

SO

NR

YC

ON

STR

UC

TIO

N

Bracing the frameBrace the frame as shown orshore to a structure above.Brace In The Direction OfIntended Wall. Plumb andsquare jambs. Install verticalbrace to support header foropenings over 4'0" wide.

SpreaderTypical wood spreader must be square and fabricatedfrom lumber no less than 1" thick. Correct length is thedoor opening width between the jambs at the header(i.e., Single Door 3'0" = 36"). Cut clearance notches forframe stops. Spreader must be nearly as wide as framedepth for proper installation.

A A

SPREADER

SECTION A-A

LEVEL

SQUARE

PLU

MB

DOOR OPNG. AT HEADER

FRA

ME

DE

PTH

1. Assemble frame.

2. Set brace and plumb frame.

3. Install anchors. Grout frame in the area of the anchors (see above)as block courses are laid up. Frames may also be supplied withanchors welded in place.

4. A second spreader isrecommended at themid point of the dooropening to maintainthe door openingdimension.

5. Continually checkplumb and square aswall progresses.

WireAnchor

“T”Anchor

90˚ 90˚

SPREADER

NOTE: Anchors in frame heads are not required.

130Recommended Erection InstructionsFRAME TECHNICAL DATAJuly 1, 2003

STE

EL

STU

DW

ALL

CO

NS

TRU

CTI

ON

WO

OD

STU

DC

ON

STR

UC

TIO

NW

OO

DS

TUD

CO

NS

TRU

CTI

ON

(STU

DS

ER

EC

TED

BE

FOR

EFR

AM

E)

Elevation1. Assemble frame.2. Install anchors. Position anchors in frame through the

throat and tap in with a hammer. Frames may also besupplied with anchors welded in place.

3. Square, brace and plumb frame as shown.4. Set spreader. Attach jambs to floor through floor anchor

or floor extension. Install jamb studs to floor and ceilingrunners and tightly against frame anchors.

5. Attach studs to frame anchors as shown.

NOTE: Drywall mustextend at least 1/2"into frame at firerated installations.

Channel type steel studPosition studs in frame throat and attach to anchors with screws orweld. If using screws, the installer should drill from the back side ofthe stud, through both the stud and anchor, then attach with (2)screws per anchor location.NOTE: When attaching header stud to jamb studs, be sure the studis above frame header. This will assure ample room for attachingplaster lath or drywall and will not interfere with installation of hardware attached to frame header. Anchors are not required inframe heads, except fire listed double egress openings.

FRAME

CHANNELTYPEJAMBSTUDS

HEADER STUD

JAMBSTUD

SPREADER

90˚ 90˚

Erect frameAssemble frame. Stand frame up in desired loca-tion. Anchor one jamb to floor and set spreaderon floor from anchored jamb to loose jamb.Position and anchor second jamb. Plumb, leveland square frame, then brace.

NOTE: Drywall must extend at least 1/2" intoframe at fire rated installations.

1. Install anchors. Position anchors in frame throat and tap in with a hammer. Frames may also be sup-plied with anchors welded in place.

2. Set spreader.Attach jambs to floor through floor anchor or

floor extension. Install double jamb studs to floor and ceiling runners and header.

3. Bend anchor tabs around stud leaving desired clearance between frame return and stud for inserting finished wall material.

4. Square and nail top anchor to stud on ONE JAMB ONLY.Check plumb and square and continue to nail balance of anchors to stud. Repeat for opposite jamb.

5. Anchors are not required in frame heads, except fire listed double egress openings.

ANGLEBRACES

SPREADER

FRAME

WOODSTUDS

FLOORRUNNER

JAMBSTUD

HEADER STUD

SPREADER

90˚ 90˚

Rough openingBuild rough opening. Rough openingdimensions for 2" face frames should be 4-1/4" - 4-1/2" larger than door width and2-1/4" - 2-1/2" larger than door height. It isrecommended that double studs be used atjambs and headers.NOTE: Drywall must extend at least 1/2"into frame at fire rated installations.

1. Assemble frame.2. Install anchors. Position

anchors in frame throat and tap in with a hammer.Frames may also be supplied with anchors welded in place. Base anchors may also be used. If base anchor cannot be used add one anchor per jamb at bottom.

3. Place frame in rough stud opening.

4. Bend anchor tabs around stud leaving desired clearance between frame return and stud for inserting finished wall material.

5. Set spreader and level frame. Shim jambs if necessary.6. Square and nail top anchor to stud on ONE JAMB ONLY. Check plumb and

square and continue to nail balance of anchors to stud. Repeat for opposite jamb.

7. Anchors are not required in frame heads, except fire listed double egress openings.

ROUGHOPENING

DIMENSIONS

SPREADER

90˚ 90˚WOODSTUDS

FRAME

JAMB STUD

131ElectroLynxTM System LX Options

FRAME TECHNICAL DATAASSA ABLOY, the global leaderin door opening solutions

May, 2005

The CURRIES LX cable is equipped with the ElectroLynxTM System of “plug-in” connectors for fast, easy, connec-tion to similarly equipped ASSA ABLOY Hardware. The LX cable has 15 conductors of 22 gauge wire in a PVCjacket, with ElectroLynx snap connectors on the hardware prep end only.

KD FRAMES – (LX) are provided with a cover box and a conduit knockout over the electric hingeprep(s), electric strike prep, and junction box in the frame head including a 1" access knockout. ElectroLynx (LX) wiring system cable(s) are included. Conduit option is loose or by others, as specified when ordered.

FACTORY – (LX) are provided with the same cover box options listed above for KD frames, WELD FRAMES conduit is included and the LX cable is installed with the ElectroLynx system in

place as ordered. The frame head junction box has electrical knockout for building wiring, and the frame head rabbet has a 1" knockout for future installation of Door Position Switch under the cover box.

– Check anchor interference with conduit, some loose anchor styles won’t work.– Some electric preps won’t allow 1/2" drywall penetration for fire rated frames.

“Hardwiring Made Easy”

6" 6" 6"CL CL CL

SECONDELECTRICHINGE IFNEEDED

HJ SJ HJ SJ HJ SJ

132CURRIElum Emergency Egress FrameFRAME TECHNICAL DATAMarch 1, 2005 ASSA ABLOY, the global leader


2-13/16"(71.4)

MINIMUMFACE

1-3/4"(44.4)

MINIMUM

NOTE: JAMB DEPTH MUST BE 1-1/8" LARGER THAN THETHROAT OPENING OR WALL THICKNESS. A 4-3/4" WALLWILL REQUIRE A 5-7/8" JAMB DEPTH FRAME.

ELECTROLUMINECENTLAMP

RACEWAY

RACEWAYENDCAP

RACEWAY ACCESSKNOCKOUT

LITEGUIDE ELECTRICALACCESS 1-1/4" (31.7)

“KNOCKOUT”5" (127) CL AFF

HOLE PLUG4"

(101.6)

6" (152.4)

THROAT IS 1-1/8" LESSTHAN JAMB DEPTH

9/16"(14.3)

9/16"(14.3)

DRYWALL RETURNPROFILE 299

MASONRY RETURNPROFILE 301

NOTE: A FULL WIDTH JUNCTION BOX IS PROVIDEDAT THE BOTTOM OF EACH JAMB. USE OF SWING-ING DOOR HARDWARE MOUNTED IN THE BOTTOM10” OF FRAME IS NOT AVAILABLE. HOLE PLUGAND ENDCAPS ARE SHIPPED LOOSE.


133Security Sidelite Door Construction

FRAME TECHNICAL DATAMarch, 2007

FEATURES:

HINGED SECURITY PANELCLOSES TO CREATE A VISUALBARRIER

GLASS POCKETS AVAILABLEFOR UP TO 1” THICK GLASS

PREPARED FOR SELF LATCH-ING DEADBOLT TO MEETPROJECT REQUIREMENTS

STANDARD 4-1/2” X .134HINGE PREPARATIONS

OPTIONS:

AVAILABLE WITH MASONRYAND STUD WALL ANCHORS

FIRE RATING:WARNOCK HERSEY3/4 HOUR RATING. (1-1/2 HOUR WITH SPECIALTYGLAZING)

USES:• CLASSROOMS• POST OFFICES• GOVERNMENT FACILITIES• AIRPORTS

16 OR 14 GA. FRAMES WITHWELDED CORNERS 6-3/4" MINIMUM DEPTH

OPERABLEPANEL

INSIDESECTIONOUTSIDE

GLASS

134Transom Frame Removable Panel InstallationFRAME TECHNICAL DATAJuly, 2007

L


16 GAUGE GUIDECHANNEL

TOP OF PANELNOTCHED FOR GUIDE CHANNELS

BOTH FACE SHEETSWELDED TO VERTICAL END CHANNELS, 6"O.C.

3/8" RETAINER PINS FOR REMOVABLE PANELS:WELDED TO INSIDE OF HEAD.6" FROM ENDS 18" MAX O.C.

TAPPED FOR1/4-20 MS

1/4" STEELPLATE

HORIZONTAL EDGES OFPANEL ARE WELDED TOCONTINUOUS CHANNEL

NOMINAL 1-3/4" THICK

1/4" STEEL PLATEWITH CLEAR HOLE

16 GAUGEGUIDE (END)CHANNELSBOTH SIDES

1/4-20 FHMS (2)

JAMB

TOP OF PANELBOTTOM OF PANEL

1-9/16"

7/8"

DRILL 1/4" AND COUNTERSINK

DOOR OPENING17/32" TO BOTTOMOF PANEL & 1/8"CLEARANCE TO TOPOF DOOR FROM BOTTOM OF PANEL

48" MAX.PANELHEIGHT

HORIZONTAL ASTRAGALREQUIRED.

PANEL - STEEL STIFFENED, MINERALCORE OR HONEYCOMB.

FRAME - 3 HR MAX. RATING11'4" MAX. HEIGHT4' MAX. WIDTH SINGLE8' MAX. WIDTH PAIR

Date post:	07-Apr-2019
Category:	Documents
Upload:	tranthien
View:	213 times
Download:	0 times

Frame Technical Data - Steel Dor of...

Documents