Complete system protection and management solutions from Texas Instruments deliver high system reliability. Analog and digital hot swap controllers provide both current and power limiting to dynamically adjust the current limit at large VDS to ensure the MOSFET stays in the Safe Operating Area (SOA) — maximizing long-term system reliability and robustness. The new family of intelligent hot swap devices feature system diagnostic and telemetry reporting which enables the system to take immediate action to control or optimize power delivery. The family of ORing FET controllers allows MOSFETs to replace diode rectifiers in power distribution networks and reduce both power loss and voltage drops while providing best-in-class reverse current protection.
System Protection and Management Portfolio
Communications Infrastructure, Merchant Power, Industrial, Automotive Applications
80V
60V
20V
10V
5V
3V
-10V
-80V
-100V
VIN
Hot Swap Control Multi-OutputHot Swap + OR-ing
OR-ing FET Control MeasurementProtection and
Control
LM5069TPS249x
LM5067/8
TPS235xTPS245x
LM5050TPS241x
LM5066PMBus
TPS248xTPS249x
LM25066PMBus
LM5064PMBusTPS239x
LM5051
LM25061/9TPS233xTPS242x
TPS247xxTPS25xxUC391x
LM25056PMBus
PowerMeasurement
220 VAC
220 VAC
DC Recti�er
A B
SMBus
Hot Swap
ORing
DC Recti�er
IBC
POL
LDO
PMBus POL
PMBusHot Swap
Loads:1V, 90A1.8V, 60A1.2V, 20A1.5V, 15A2.5V, 15A5V, 10A0.9V, 3A2.8V, 0.5A
Line Card
Peripheral Card
-48V
IN-B
IN-A
RTN-B
RTN-A
Reverse Current Protection
ORing
POL
PMBus POL
Typical System Application
Front-End System Protection & Power Management SolutionsIncreased System Reliability and Efficiency
1Q 2012www.ti.com
Hot Swap Protection and Measurement
Hot swap controllers are the power gate keepers that control the flow of power into the board, monitor for fault conditions, and protect against undesirable events. TI’s hot swap controller and high-side protection solutions provide robust front end protection for a range of communication infrastructure, merchant power, industrial, and automotive applications.
Typical Application CircuitTI’s PMBus-enabled system protection and management products combine hot swap control with embedded telemetry measurement, intelligence, and digital communications which enable them to deliver accurate power usage data back to the system to optimize power consumption, reduce operating expenses, and increase reliability.
Features• Hot swap/In-rush control• Adjustable input current and input power limiting enable use of
smallest MOSFETs• Circuit breaker for over-current events• Programmable under-voltage and over-voltage thresholds• Fast response to fault current conditions
Power Limiting ProtectionTo ensure system reliability, MOSFET drivers must operate within the SOA in order to avoid FET failure. Most hot swap controllers control only the current, but when the FET is turning on, the voltage across it can still be large and the power through the FET can cause it to exceed its SOA curve unless the design accounts to over-size the FET, which adds both cost and size. TI’s hot swap controllers provide both current and power limiting to dynamically adjust the current limit at large VDS and ensure the MOSFET stays in the SOA at all conditions. This technique enables the use of smaller and lower cost MOSFETs.
LM25066
VSYS V OUT
PowerGood
GND
UVLO
SCL
PWRGNDTIMER
PGD
OUTVIN SENSE GATE
SMBusInterface SDA
SMBA
ADR0ADR1ADR2
AUX
D+
VDD
OVLO
V AUX
FB V PG
RETRY
CLCB
VREF
Features• Hot swap with current and power limiting• Adjustable current limit, circuit breaker thresholds• Measure voltage, current, power, and temperature •Simultaneoussamplingofcurrentandvoltagefortruepower
measurement• Peak and programmable average power capture• Dynamic configuration of fault and warning levels • I2C/SMBus interface with PMBus compliance
1 10 100 1000
VDS , Drain-to-Source Voltage [V]
0.1
1
10
100
1000I D
, Dra
in-t
o-So
urce
Cur
rent
[A]
100 µsec
1 msec
10 msecMOSFET Safe Operating Area (SOA)
Current Limit OnlyCurrent Limit
Power Limit
TI’s Current and Power Limiting Protection
VIN VOUT
PowerGOOD
UVLO
OVLO
PWR GNDTIMER
PGD
OUTVIN SENSE GATE
LM5069
Typical Application Circuit
System Protection and Power Management Texas Instruments 1Q 2012
Hot Swap Protection and Measurement Hot Swap Protection and Measurement
Hot Swap/In-Rush Current Controllers
System Protection and Power Management Texas Instruments 1Q 2012
Device VINRange(V)Enable/
Shutdown UV OV Fault PG LatchAuto Retry Ramp
Power Limiting Package(s)
TPS2400 2to100 1H ✔ ✔ ✔ — No 5-pinSOT-23
TPS24700/01 2.5to18 1H ✔ ✔ ✔ Current No 8-pinMSOP
TPS24710 2.5to18 1H ✔ L L ✔ Current Yes 10-pinMSOP
TPS24711 2.5to18 1H ✔ L L ✔ Current Yes 10-pinMSOP
TPS24712/13 2.5to18 1H ✔ H H ✔ Current Yes 10-pinMSOP
TPS24720 2.5to18 1H ✔ ✔ ✔ ✔ S2 S2 Current Yes 16-pinSON
LM25069 2.9to17 1H ✔ ✔ ✔ H -1 -2 Current Yes 10-pinMSOP
LM25061 2.9to17 1H ✔ ✔ H -1 -2 Current Yes 10-pinMSOP
LM25066/A 2.9to17 1H ✔ ✔ ✔ ✔ Prog Prog Current Yes 24-pinLLP
UCC3919 3to8 1H ✔ S1 S1 Current No 16-pinSOIC/TSSOP
TPS2330/31 3to13 1L/1H ✔ ✔ ✔ ✔ Voltage No 14-pinSOIC/TSSOP
TPS2300/01 3to13/3to5.5 1L/1H ✔ ✔ ✔ ✔ Voltage No 20-pinTSSOP
TPS2310/11 3to13/3to5.5 1L/1H ✔ ✔ ✔ ✔ Voltage No 20-pinTSSOP
TPS2320/21 3to13/3to5.5 1L/1H ✔ ✔ ✔ ✔ Voltage No 16-pinSOIC/TSSOP
TPS2363 3.3Vaux,3.3,+12 1L ✔ ✔ ✔ ✔ Voltage No 48-pinQFP
TPS2342 3.3,Vaux,VIO,5,+12,–12 1L ✔ ✔ ✔ Voltage No 80-pinHTQFP
TPS2343 3.3,Vaux,VIO,5,+12,–12 1L ✔ ✔ ✔ Voltage No 80-pinHTVSOP
LM5060/Q 5.5to65 1H ✔ ✔ ✔ L ✔ Voltage No 10-pinMSOP
TPS2456 8.5to15 2H ✔ ✔ ✔ ✔ Current No 36-pinQFN
TPS2458/59 8.5to15 1L ✔ ✔ ✔ ✔ Current No 32-pinQFN
TPS2358 8.5to17 2L ✔ ✔ ✔ ✔ Current No 48-pinQFN
TPS2359 8.5to17 1H/1L ✔ ✔ ✔ ✔ S1 S1 Current No 36-pinQFN
TPS2480/81 9to80 1H ✔ ✔ ✔ Current Yes 20-pinTSSOP
TPS2490/91 9to80 1H ✔ ✔ ✔ Current Yes 10-pinMSOP
TPS2492/93 9to80 1H ✔ ✔ ✔ ✔ ✔ Current Yes 14-pinTSSOP
LM5069 9to80 1H ✔ ✔ ✔ H -1 -2 Current Yes 10-pinMSOP
LM5067 -9to-80 1H ✔ ✔ ✔ H -1 -2 Current Yes 10-pinMSOP,10-pinLLP
LM5066 10to80 1H ✔ ✔ ✔ ✔ Prog Prog Current Yes 28-pineTSSOP
LM5064 -10to-80 1H ✔ ✔ ✔ ✔ Prog Prog Current Yes 28-pineTSSOP
LM5068 -10to-90 1H ✔ ✔ ✔ H/H/L/L -1/-3 -2/-4 Current No 8-pinMSOP
TPS2350 –12to–80 1H ✔ ✔ ✔ ✔ ✔ Current No 14-pinSOIC/TSSOP
TPS2394 –12to–80 1H ✔ ✔ ✔ ✔ ✔ Current No 14-pinTSSOP
TPS2395 –12to–80 1H ✔ ✔ ✔ ✔ ✔ Current No 20-pinTSSOP
TPS2392 –20to–80 1H ✔ ✔ ✔ ✔ ✔ Current No 14-pinTSSOP
TPS2393/A –20to–80 1H ✔ ✔ ✔ ✔ ✔ Current No 14/44-pinTSSOP
TPS2390 –36to–80 1H ✔ ✔ Current No 8-pinMSOP
TPS2391 –36to–80 1H ✔ ✔ Current No 8-pinMSOP
TPS2398 –36to–80 1H ✔ ✔ Current No 8-pinMSOP
TPS2399 –36to–80 1H ✔ ✔ Current No 8-pinMSOP
Design Tools
USB
to PMBus
Eval Board Software
Design & Evaluation Tools
TI offers a full suite of design resources and evaluation tools, such as application notes, reference designs, demo videos, a hot swap component calculator, WEBENCH® Power Architect, PowerLab, and other design tools.
Component Calculator Design and Evaluation GUI tool
Evaluate solutions for your system with an easy-to-use design calculator and PMBus configuration
software that includes real-time data logging.
© 2012 Texas Instruments IncorporatedPrinted in U.S.A. by (Almaden Press, San Jose, CA)
The platform bar, E2E, and PowerLab are trademarks of Texas Instruments. WEBENCH is a registered trademarkAll other trademarks are the property of their respective owners.
SLPB011A
ORing MOSFET Controllers
High-side ORing MOSFET controllers improve redundant power supply reliability by delivering ideal diode response to reverse current. Using LM5050 to control MOSFETs as a replacement for a Schottky ORing diode also improves the efficiency of the redundant power supplies. An ultra-fast 50 ns shut off significantly limits the flow of reverse current.
Hot Swap Protection and Measurement
Device VIN Range (V) Enable/
Shutdown UV OV Fault PG ORing Linear Gate Drive?
On/Off ORing Function? Package(s)
TPS2410 0.8 to 16.5 1H ✔ ✔ ✔ ✔ ✔ 14-pin TSSOP
TPS2411 0.8 to 16.5 1H ✔
TPS2412 0.8 to 16.5 ✔ 8-pin SOIC, 8-pin TSSOP
TPS2413 0.8 to 16.5 ✔ 8-pin SOIC, 8-pin TSSOP
TPS2419 3 to 16.5 1H ✔ ✔ 8-pin SOIC
LM5050-1 5 to 80 L ✔ ✔ 6-pin TSOT
LM5051 –6 to –100 L ✔ ✔ ✔ 8-pin SOIC
LM5050-2 6 to 80 L ✔ ✔ ✔ 6-pin TSOT
TPS2456 8.5 to 15 2H ✔ ✔ ✔ ✔ 36-pin QFN
TPS2358 8.5 to 15 2L 48-pin QFN
TPS2359 8.5 to 15 Via I2C 36-pin QFN
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,and other changes to its products and services at any time and to discontinue any product or service without notice. Customers shouldobtain the latest relevant information before placing orders and should verify that such information is current and complete. All products aresold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standardwarranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except wheremandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products andapplications using TI components. To minimize the risks associated with customer products and applications, customers should provideadequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Informationpublished by TI regarding third-party products or services does not constitute a license from TI to use such products or services or awarranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectualproperty of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompaniedby all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptivebusiness practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additionalrestrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids allexpress and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is notresponsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonablybe expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governingsuch use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, andacknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their productsand any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may beprovided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products insuch safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products arespecifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet militaryspecifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely atthe Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products aredesignated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designatedproducts in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265Copyright © 2012, Texas Instruments Incorporated