Fuel Storage & Control SystemsGenerator Packaging & Enclosures

phoenixproducts™

1727 Bennett Street, Jacksonville, FL 32206 • 904-354-1858 • 904-354-7929 Faxphoenix.sales@phoenixprods.com • www.phoenixprods.com

Options Include: Double-Walled & Fire Rated Tanks,Hurricane Rated & Sound Attenuated Enclosures

fueltanks Aboveground & Sub Base Tanks

Envirovault & Fire-Steel® • UL2085 Protected Aboveground Tanks

True double-wall construction with lightweight concrete filled interstitial spacen UL 2085 listed and labeled – Protected aboveground

tank for flammable and combustible liquidsn Fire, vehicle impact and ballistic ratedn Meets requirements for secondary containment, leak

monitoring, spill containment, and overfill protectionn Inner and outer tanks constructed per UL 142 – Steel

aboveground tanks for flammable and combustible liquidsn Six inches of lightweight concrete protection between inner

and outer tanks provides minimum two-hour fire ratingn High-build polyester epoxy glassflake impregnated coating

used for salt water submersion protection on offshore platforms, 20,000 hour ASTM B117 salt spray tested

n Primary and emergency vents standardn All fittings and protrusions are stainless steeln Steel support channel allow visual tank

bottom inspection and air circulation

Designed to meet or exceed national, state and local codesn No exposed concreten Exceeds liability insurance requirementsn Engineered for seismic IBC standardsn Integral earthquake and hurricane tie downsn Leak detection space providedn Meets NFPA 30 and 30A Options

n Stairs and platforms (aluminum/galvanized steel) meeting OSHA standards with handrails

n Stainless steel inner and outer tanksn Fuel heaters n Stainless steel inner and outer tanksn Multiple internal compartmentsn Stainless steel accessory equipment

boxes and top/remote fill boxesn Fuel monitoring and control systemsn Tank top hand rails approved by OSHAn Day tanks with supply and return pumpsn Custom color matchingn Fuel polishing systemsn Dispensing equipment

PowerTank & Double-Wall • UL142 Secondary Containment Tanks

Steel aboveground tanks for flammable and combustible liquidsn UL 142 listed and labeled – protected aboveground

tank for flammable and combustiblen Meets requirements for secondary containment, leak

monitoring, spill containment, and overfill protectionn No external cross beams or side supports to interfere

with generator placement or stairs and walkwaysn Supports generator sets up to 80,000

pounds, with or without enclosuresn Primary and emergency vents standardn Rounded corners allowing proper adherence

of industrial grade enamel coatingn Steel support channel allow visual tank

bottom inspection and air circulation

Designed to meet or exceed national, state and local codesn NFPA 30, 30A, 37 & 110n True double-wall construction for UL certificationn Exceeds liability insurance requirementsn Engineered for seismic ratingn Earthquake and hurricane tie downsn Leak detection space provided

Optionsn Stairs and platforms (aluminum/galvanized

steel) meeting OSHA standards with handrailsn Fuel heatersn Stainless steel fittings, protrusions and fill boxesn Stainless steel inner and outer tanksn Custom color matchingn Over-fill spill protectionn Fuel polishing systemsn Dispensing equipmentn Fuel monitoring and control systemsn Day tanks with supply and return pumpsn Tank top hand rails approved by OSHAn Manway accessn Remote fill

generatorenclosuresGenset Enclosures

Weather Proof, Sound Attenuated, High Velocity-Hurricane Zone & Agency for Health Care Administration

Fully weather, corrosion and wind load resistant all aluminum enclosuren Interlocking aluminum panels, make a

lightweight and corrosion resistant housingn Standing seam sloped roof, mill-finish aluminumn Fixed intake louvers with expanded

aluminum and gravity dampers on discharge provide water intrusion prevention

n Weather-proof gasket and stainless steel hardware on 36-inch doors with padlocking handles

n Reinforced door and roof structuren Wind load rating 150 MPH Optional 200 MPH

ALL ALUMINUM, CORROSION, WEATHER, WIND & MISSILE-IMPACT

RESISTANT ENCLOSURES

Optional Certificationsn Miami-Dade County Notice of Acceptancen Department of Business and

Professional Regulationsn Florida Building Code

SUPERIOR STRUCTURAL DESIGN & MISSILE IMPACT PROTECTION

Enclosure Optionsn Motorized air intake and discharge dampersn Stainless steel hold-downsn Sound attenuationn Three point door latches with padlocking handlesn Reinforcements at all corners and openingsn 200 MPH wind load constructionn PE signed & sealed drawingsn Interior silencern Interior AC and DC lights with timer switchn Exterior emergency stop stationn Electrical and lighting systemsn Custom paint matchingn AHCA Compliancen High Velocity Hurricane Zone Rating

PROTECTIVE ENCLOSURES FOR ALL GENERATOR SIZES

moreproducts

High quality, economical Fuel Storage and Enclosures

for Generators 300kW and Lower

Falcon Enclosures

& Tanks

n UL 142 Listed, FDEP Compliant – both inner and outer tanks are completely sealed and pressure tested

n Meets requirements for secondary containment, leak monitoring, spill containment, and overfill protection

n Supports generators up to 300KWn Accommodates Phoenix Products and factory generator

enclosures, both weather-proof and sound attenuatedn Fill cap, primary vents and emergency

vents package standardn Steel 2-inch channel supports, allow visual

inspection of tank bottom as well as air movement to prevent condensation induced corrosion

n Black satin industrial grade enamel paint

n Spill containment with spring-loaded drain valven Leak sensor proben Low and high fuel level floatsn Interlocking aluminum panels, make a

lightweight and corrosion resistant housingn Standing seam sloped roof, mill-finish aluminumn Fixed intake louvers with expanded aluminum and gravity

dampers on discharge provide water intrusion preventionn Weather-proof gasket and stainless steel hardware

on 36-inch doors with padlocking handlesn Reinforced door and roof structuren Wind load rating 120 MPH; Optional 150 MPH

Diesel Director Day Tanksn UL 142 double

wall secondary containment tanks

n Optional UL 2085 interstitial concrete filled double wall tanks with 2-hour fire rating

n Supply & return pumpsn Control panel with high

and low level alarmsn Leak sensorn Emergency and

Primary ventsn Gauge stickn Float fuel leveln Mechanical leak sensorn Spare fittings portsn Tank drains with

ball valven Lockable fill capn Phoenix Products

coating systemn Optional OSHPD

certification

Diesel Director Remote Fillport

n Ground level connection to fuel truck fill hosen Single or multiple tanksn Spill containmentn Optional control panel and 2, 3 or 4 inch fill

pipe sizes with or without booster pumpsn Lockable, weatherproof

stainless steel enclosuren Hand pump dischargen Two-point alarm for high and leak indicationn Optional control panel with tank selector,

automatic ball valves, digital capacity displayn Optional stainless steel base standn Additional ball valves UL listedn Optional flanged automatic valvesn Optional fusible link fire valvesn Optional high capacity pump and motor

for fuel transfer from gravity trucks

aboutusAbout Phoenix ProductsBased in Jacksonville, Florida, Phoenix Products was established in 1991 as a fuel tank supplier. Our heritage differentiates us from other generator packagers because of our expertise in fueling systems. In fact, we pioneered several innovative fueling alternatives, now widely used and required by many regulatory agencies. For example, our patented Fire-Steel® Generator Base Tank, which was the first UL2085 listed base tank, is now a regulatory requirement in many jurisdictions. Also, our Pipe Daytank System allows placement of emergency power systems in locations where it once was impractical or simply not allowed.

We understand that fueling systems are an integral part of any Emergency Power System design; not an afterthought.

Built to LastPhoenix Products is a pioneer in the use of aluminum structures for enclosure design. Most competitive generator packages are built with steel housings. Our interlocking panel design provides the corrosion resistance of aluminum, yet provides the structural integrity of up to a 200 MPH wind rating, and sound attenuation options up to 45 dBA reduction.

One Call Does It AllWith more than 20 years of experience and customers in a variety of environments, we are familiar with virtually every possible requirement or expectation. Our fabrication technicians are highly trained, extremely talented and willing to take on challenging builds. So if you have a special need or custom request, just ask.

Phoenix Products is committed to providing superior product design, exceptional quality, timely delivery and competitive pricing.

1727 Bennett Street, Jacksonville, FL 32206 • 904-354-1858 • 904-354-7929 Faxphoenix.sales@phoenixprods.com • www.phoenixprods.com

phoenixproducts™

1727 Bennett Street, Jacksonville, FL 32206 • 904-354-1858 • 904-354-7929 Faxphoenix.sales@phoenixprods.com • www.phoenixprods.com