Fuller® Heavy-Duty Transmissions TRMT0951 EN-US...7. Identification chart for RT-8609, RT-7608LL,...

Unit Exchange Guide

Fuller® Heavy-Duty TransmissionsTRMT0951 EN-USSeptember 2007

1

Table of Contents

New Unit Exchange Program Overview ....................... 2Introduction and Explanation ...................................... 3Unit Identification For Unit With Transmission Tag...... 4Transmission Interchange Section Header

Descriptions ......................................................... 5Output Yokes (Chart C) ............................................... 7Shipping Weights ...................................................... 13Transmission Oil Capacities ...................................... 14

2

New Unit Exchange Program Overview

New Unit Exchange Program Overview

The Transmission Unit Exchange Program was created to make ordering Reman, New, or New Unit Exchange units a simple process. Please carefully read the details of this program before continuing into the interchange section of this book.

This book is organized in a way to help you order all the parts needed when ordering a Reman, New, or New Exchange Unit.

This book is divided into 15 sections:

1. Introduction and Explanation of Service Unit Exchange Program.

2. Unit identification – Locating Transmission Tag and Identifying Model Designation.

3. Unit identification – How to identify a unit when the identification tag is missing.

4. Options identification – How to identify various options the transmission may currently have, and whether or not a service unit for those options is available.

5. Clutch Housing identification – How to determine the part number of a clutch housing.

6. Transmission Interchange – How to determine the part number for Reman, New Unit, or New Exchange Unit by model.

7. Identification chart for RT-8609, RT-7608LL, RT/RTO-6610, or RT/RTO-6613 (Chart A) – To order the Reman version of these three models, identify the input shaft and front bearing cover.

8. Conversion Chart (Chart B) – When the current model is replaced by a Reman, New, or New Unit Exchange model that has a ratio or length change, refer to this section.

9. Recommended Stocking Guide – Clutch housings and/or shift bar housing assemblies.

10. Quick Reference Guide – To identify the model or "TA" number.

11. Accessories – To order various accessories for your Reman, New, or New Exchange Unit. This section lists part numbers for accessories by model.

12. Output Yoke Chart (Chart C) – Describes how to determine the yoke series, and part number.

13. Speedometer Parts – To order new speedo parts for your Reman, New, or New Exchange Unit. This section is divided into Mechanical and Magnetic sections.

14. Shipping weights.

15. Transmission Oil Capacities.

3

Introduction and ExplanationIntroduction

Introduction and Explanation

This book contains information needed to cross reference most Fuller transmission models produced between the years 1985 and 1998. With this book you will have the ability to order and/or stock a Reman, New, or New Exchange Unit to meet customer requirements. This book groups all units together, based on speed and model, and it references SERVICE UNIT part numbers to be used when ordering or stocking service units.

In addition to offering a complete transmission interchange, this catalog contains information helpful in cases where it may be necessary to order other components when ordering a Reman, New, or New Exchange Unit. For example, in the Accessories Section you can look for a specific yoke application, push-in sensor rear bearing cover assembly, master valve with a generic medallion, generic medallion only, master valve with shift diagram medallion, shift diagram medallion only, or shift label only for ANY particular model. Other accessories covered are: service lever assemblies, Roadranger valve repair kits, and speedometer parts.

As stated above, there are three types of replacement units – Reman, New, or New Exchange. All Reman and New Exchange units have a CORE CHARGE. Please see publication APSL0419 for core and warranty details.

These units are “All-Makes” in nature, meaning they are ALL built with a Service Shift Bar Housing (with provisions for neutral light switch, reverse light switch, and breather), and a Service Rear Bearing Cover (with provisions for BOTH mechanical and magnetic pickups). Most service units are built standard with a 2" pull-type input shaft.

Most Service Units can be purchased with an integral oil pump option.

Please note that New and New Exchange Units are shipped WITHOUT a Clutch Housing. Reman units will continue to be shipped WITH a SAE #1 Clutch Housing (or SAE #2 for 6600 model series).

Information contained in this publication is also available on the Eaton web site: http://truck.eaton.com and on a CD-ROM called Specranger. Copies of Specranger can be obtained by contacting your local Eaton Roadranger Parts Marketing District Manager. For more information, call 1-800-826-HELP, (826-4357).

4

Unit Identification For Unit With Transmission Tag

Unit Identification For Unit With Transmission Tag

The first step in the process of ordering a service unit is determining the current model. There are two ways to do this. The first way is to locate the tag on the side of the transmission and identify its model designation. The second way is, if the unit does not have a tag follow the transmission identification chart in the next section to determine the model. When the current model is identified, proceed to Transmission Interchange Section.

Locating Transmission Tag and Identifying Model Designation

Transmission model designation (i.e. RT-12609A), and other transmission identification information, are stamped on the trans-mission tag. To identify the transmission model designation (nomenclature), locate the tag on the transmission and then locate the model designation number as shown.

Using Model Designation or Nomenclature

The model designation or nomenclature assigned to a transmission model provides information concerning transmission torque capacity, forward speeds, ratio set, shift bar housing and other provisions and options. Use the following guidelines to identify your transmission model designation.

Heavy Duty Transmission - Nomenclature

Location of Transmission Tag

Heavy Duty Models

Location of Transmission Tag on "FR" Models

Eaton FullerTransmissions

PTO Code

Model Serial

MadeIn

Eaton CorporationTransmission DivKalamazoo, MI 49003

R T O - 1 1 9 0 9 M L LEaton Fuller Model Designation PrefixSee options below:

Prefix DefinitionT Twin CountershaftTX w/OverdriveRT Roadranger Twin CountershaftRTF w/ Forward Shift Bar HousingRTO w/ OverdriveRTOF w/ Overdrive and Forward Shift Bar HousingRTX w/ Overdrive and Direct Shift PatternRTXF w/ Overdrive, Direct Shift Pattern and Forward Shift Bar HousingFR Fuller Roadranger Twin CountershaftFRF w/ Forward Shift Bar HousingFRO w/ OverdriveFROF w/ Overdrive and Forward Shift Bar Housing

Ratio Set

Forward Speeds

6 = “Multi-Mesh” Gearing7 = Helical Auxilary Gearing and

“Multi-Mesh” Front Gearing2 = Design Level

9 = Improved Seal System

This (x) 100 = Nominal Torque Capacity

L or LL notation used here indicates one (L)or two Low (LL) gears in addition to designated speeds

“Super” Transmissions R T L O F* - 1 4 6 1 0 ARoadrangerTwin CountershaftLow-InertiaO = OverdriveF* = Forward Mounted Shift Tower* Transmission nomenclature may indicate a Standard (RTLO) or Forward (RTLOF) Mounted Shift Tower.

Ratio SetForward Speeds

6 = “Multi-Mesh” GearingThis (x) 100 = Nominal Torque Capacity

®

® ®

® ®

®

5

Transmission Interchange Section Header Descriptions

Transmission Interchange


Before continuing into the main interchange section of this catalog, read below for header explanation.

Model:Find your transmission model on the metal serial tag, please refer to page 4 for locating the serial tag. If the tag is missing, see the Transmission Identification Chart to determine the transmission model. Many options are not identified in the model number of the transmission. For proper identification of which options your transmission may have, please see the Options Chart.

NOTE: Models listed in the MODEL column that have an “*” after the model listing are NOT eligible for a core return credit.

Reman Unit Model Designation: Reman models currently available.

Reman Unit Part Number Without Integral Oil Pump:Reman transmission models include an SAE #1 standard clutch housing, except the 6600 series, which includes an SAE #2 standard clutch housing. Reman units purchased require a core return (Except in cases where an “*” appears beside the Model listed, means NO CORE VALUE. For core and warranty details, please refer to publication #ASPL0419.

Many Fuller Transmissions are built today with an integral oil pump. This option is not indicated on the original transmis-sion’s identification plate. Please see the Options Chart to determine whether an integral oil pump is present. Integral oil pump options for all Reman, New and New Exchange Units are indicated by a suffix of “11” – indicating NO PUMP, or “12” – indicating PUMP. Part numbers for Reman transmis-sions are all followed by an “R”. For example: the Reman part number for an RTX-12609A without an integral oil pump would be TA-830-11R.

Reman Unit Part Number With Integral Oil Pump:Reman transmission models include an SAE #1 standard clutch housing, except the 6600 series, which includes an SAE #2 standard clutch housing. Reman units purchased require a core return (Except in cases where an “*” appears beside the Model listed, means NO CORE VALUE. For core and warranty details, please refer to publication #ASPL0419.

As an extra cost option, an integral oil pump can be ordered on most Reman transmission models. Many Fuller Transmis-sions are built today with an integral oil pump. This option is not indicated on the original transmission’s identification plate. Please see the Options Chart to determine whether an integral oil pump is present. Integral oil pump options for all Reman, Unit Exchange and New Service Units are indicated by a suffix of “11” – indicating NO PUMP, or “12” – indicating PUMP. Part numbers for Reman transmissions are all fol-lowed by an “R”. For example: the Reman part number for an RTX-12609A with an integral oil pump would be TA-830-12R.

Service Unit Model Designation:This is the list of New Service models currently available in production.

Service Unit Part Number Without Integral Oil Pump:New Service Units are shipped without clutch housings. To determine the proper clutch housing to order, please refer to the Clutch Housing Identification Section. These units include a service rear bearing cover (with provisions for both mechanical AND magnetic speedometer pickups), and service shift bar housing (with provisions for neutral light switch, reverse light switch, and breather). As an extra cost option, an integral oil pump can be ordered on most New, and New Exchange transmission models. Many Fuller Transmissions are built today with an integral oil pump. This option is not indicated on the original transmission’s identification plate. Please see the Options Chart to determine whether an integral oil pump is present. For warranty details, please refer to publi-cation #ASPL0419. Integral oil pump options for all Reman, Unit Exchange, and New Service Units are indicated by a suf-fix of “11” – indicating NO PUMP, or “12” – indicating PUMP. For example: the New Service Unit part number for an RTX- 12609A without an integral oil pump would be TA-830-11.

6


Service Unit Part Number With Integral Oil Pump:New Service Units are shipped without clutch housings. To determine the proper clutch housing to order, please refer to the Clutch Housing Identification Section. These units include a service rear bearing cover (with provisions for both mechanical AND magnetic speedometer pickups), and service shift bar housing (with provisions for neutral light switch, reverse light switch, and breather). As an extra cost option, an integral oil pump can be ordered on most New, and New Exchange transmission models. Many Fuller Transmissions are built today with an integral oil pump. This option is not indicated on the original transmission’s identification plate. Please see the Options Chart to determine whether an integral oil pump is present. For warranty details, please refer to publi-cation #ASPL0419. Integral oil pump options for all Reman, Unit Exchange, and New Service Units are indicated by a suf-fix of “11” – indicating NO PUMP, or “12” – indicating PUMP. For example: the New Service Unit part number for an RTX-12609A with an integral oil pump would be TA-830-12.

Service Unit Exchange Part Number Without Integral Oil Pump: New Service Units are shipped without clutch housings. To determine the proper clutch housing to order, please refer to the Clutch Housing Identification Section. These units include a service rear bearing cover (with provisions for both mechanical AND magnetic speedometer pickups), and service shift bar housing (with provisions for neutral light switch, reverse light switch, and breather). As an extra cost option, an integral oil pump can be ordered on most New and New Exchange transmission models. Many Fuller Transmissions are built today with an integral oil pump. This option is not indicated on the original transmission’s identification plate. Please see the Options Chart to determine whether an integral oil pump is present. A core value for new service units is the amount you will be billed if an acceptable core is not returned against the purchase of a New Exchange Transmission (Except in cases where an “*” appears beside the Model listed, means NO CORE VALUE). For core and warranty details, please refer to publication #ASPL0419. Integral oil pump options for all Reman, Unit Exchange, and New Service Units are indicated by a suffix of “11” -– indicating NO PUMP, or “12” – indicating PUMP. Part numbers for Service Unit Exchange transmissions are all followed by an “X”. For exam-ple: the Service Unit Exchange part number for an RTX-12609A without an integral oil pump would be TA-830-11X.

Service Unit Exchange Part Number With Integral Oil Pump:New Service Units are shipped without clutch housings. To determine the proper clutch housing to order, please refer to the Clutch Housing Identification Section. These units include a service rear bearing cover (with provisions for both mechanical AND magnetic speedometer pickups), and service shift bar housing (with provisions for neutral light switch, reverse light switch, and breather). As an extra cost option, an integral oil pump can be ordered on most New and New Exchange transmission models. Many Fuller Transmissions are built today with an integral oil pump. This option is not indicated on the original transmission’s identification plate. Please see the Options Chart to determine whether an integral oil pump is present. A core value for new service units is the amount you will be billed if an acceptable core is not returned against the purchase of a New Exchange Transmission (Except in cases where an “*” appears beside the Model listed, means NO CORE VALUE). For core and warranty details, please refer to publication #ASPL0419. Integral oil pump options for all Reman, Unit Exchange, and New Service Units are indicated by a suffix of “11” – indicating NO PUMP, or “12” – indicating PUMP. Part numbers for Service Unit Exchange transmissions are all followed by an “X”. For exam-ple: the Service Unit Exchange part number for an RTX-12609A with an integral oil pump would be TA-830-12X.

Is Service Unit Same Length and PTO Speed As Model?:If your model supersedes to a different new or new exchange model, please check this column to verify if the new model will not have any fit-up differences with regard to overall unit length and whether or not there is any differences in the PTO speed. If “NO”, please see the Conversion Chart B for details.

See Conversion Chart?:If “YES”, then the new service unit will have ratio changes. Please refer to the Conversion Chart B (conversion chart B is arranged by model and speed). The ratios for both the model that is being replaced and the service unit are listed for com-parison. Changing ratios can affect startability, road speed, and steps between gears. Also listed are weights, overall lengths, and PTO speeds as a % of engine speed.

7

Output Yokes (Chart C)Output Yokes (Chart C)

Output Yokes (Chart C)

To determine the proper part number to order for a new yoke, the following information is required.

1. What STYLE? – Half round, Full round, or Flange (See Figure 1)

2. What SERIES? – To determine series, take 3 mea-surements (See Figure 2) and apply them to Table 1 below.

3. What APPLICATION NUMBER? – To determine application number, refer back to the accessories section. Find the model you are fitting with the yoke and locate the number in the column with the head-ing “Model Yoke Application”.

4. Once Style, Series and Application Number have been determined, continue to Chart C to locate the corresponding application number section. Within each application number section you can order a yoke either with or without a slinger, based on style, series, tapped, or non-tapped holes. The current seal system utilizes the yoke with slinger design. All units shipped are to this design level (yoke w/slinger).

Figure 1

Figure 2

Table 1 Dimensions in Inches

Dimension A 4-3/4 4-15/16 5-3/16 5-1/4 5-1/4 5-1/4

Dimension B 1-7/8 1-7/8 1-15/16 1-15/16 1-15/16 1-15/16

Dimension C 5-5/16 5-5/16 6-1/16 6-1/16 7 7-1/2

Yoke Series 1610 1610 1710 1710 1760 1810

Dimension A 5-5/16 5-7/16 6 6-1/8 6-3/16 6-3/8

Dimension B 1-7/8 1-15/16 1-7/8 1-15/16 1-7/8 1-15/16

Dimension C 5-5/16 6-1/16 5-5/16 6-1/16 5-5/16 6-1/16

Half Round Full Round Flange

8


APPLICATION “1”MAJOR DIAMETER 2.500 - 10 SPLINE - HUB DIAMETER AT OIL SEAL 3.750

HalfRound

FullRound

Flange TappedHoles

Non-TappedHoles

Yoke Series

Notes PartNumberWithoutSlinger

PartNumberWithSlinger

X X 1710 86717 A-5064

X X 1710 1/2 - 20 TAPPED HOLES 86749 A-5190

X X 1650/1710 86761 A-5252

X X 1760 86716 A-5061

X X 1760 86760 A-5251

X X 1760 1/2 - 20 TAPPED HOLES 86762 A-5262

X X 1810 86718 A-5079

X X 1810 1/2 - 20 TAPPED HOLES 86769 A-5412

T11607A RTX11609A RTX12609R RT7608LL RTX11710B RT13710B RTLO12713A

T11607B RTX11609B RT12709H RTO11608LL RTX11710C RTX13710B RT11615

RT11608 RTX11609P RTX12709H RTX11608LL RT12610 RTX13710C RTO11615

RT8608L RTX11609R RT13609A RTO11708LL RTLO12610B RT6613 RTX11615

RT8709B RTX11709H RTX13609A RTX11708LL RTO12610 RTO6613 RT11715

RT11609A RTO12609A RTX13609B RT11610 RTX12610 RT11613 RTO11715

RTO11609A RTO12609B RTX13609P RTLO11610B RT12710B RTO11613 RTX11715

RTO11609B RTX12609A RTX13609R RTO11610 RTX12710B RTOO11613

RT11709H RTX12609B RT13709H RTX11610 RTX12710C RTOOF11613

RT12609A RTX12609P RTX13709H RT11710B RTLO13610B RTO11813

9


APPLICATION “2”MAJOR DIAMETER 2.750 - 10 SPLINE - HUB DIAMETER AT OIL SEAL 3.750

HalfRound

FullRound

Flange TappedHoles

Non-TappedHoles

Yoke Series



X X 1710 86719 A-5080

X X 1710 1/2 - 20 TAPPED HOLES 86765 A-5291

X X 1760 86720 A-5081

X X 1760/1810 86728 A-5082

X X 1760 1/2 - 20 TAPPED HOLES 86771 A-5416

X X 1810 86721 A-5073

X X 1810 1/2 - 20 TAPPED HOLES 86770 A-5413

AT1202 RTX14609P RTLO14610B RTX16710C RTO15813 RTO15715

RTO11607L RTX14609R RTO14610 RTLO18610B RTLO16713A RTX15715

RT14608 RT14709H RTX14610 RTLOF18610B RT14615 RTLO14618A

RTO11607LL RTX14709H RTX14610A RT14613 RTO14615 RTLO14718B

RTO11707DLL RTX16709B RT14710B RTLO14613B RTX14615 RTO15618

RTO11707LL RTX16709H RTX14710B RTO14613 RT14715 RTLO16618A

RTO13707MLL RTO14608LL RTX14710C RTOO14613 RTO14715 RTLO16718B

RT14609A RTX14608LL RTLO15610B RTOOF14613 RTX14715 RTLO18718B

RTO14609A RTO14708LL RTX15710B RTLO14713A RT15615

RTO14609B RTX14708LL RTX15710C RTO14813 RTO15615

RTX14609A RT14610 RTLO16610B RT15613 RTX15615

RTX14609B RTLO14610A RTX16710B RTO15613 RT15715

NOTE: Older generations of the above models used a yoke or flange with a 3.500 diameter hub at seal area.For these applications, use 20807 or equivalent seal with 3.750 diameter hub on yoke or flange listed above.

10


APPLICATION “3”

APPLICATION “4”

APPLICATION “5”

MAJOR DIAMETER 2.250 - 10 SPLINE - HUB DIAMETER AT OIL SEAL 3.500 - ALSO SEE APP. “8”

HalfRound

FullRound

Flange TappedHoles

Non-TappedHoles

Yoke Series



X X 1610 86734 N/A

X X 1610 86757 N/A

X X 1710 86733 N/A

X X 1710 86735 N/A

X X 1710 1/2 - 20 TAPPED HOLES 5505506 N/A

X X 1760 86724 N/A

2A92 T11605B T11605D T11605M RT8609A RTO6610

T11605A T11605C T11605F RT6609A RT6610

MAJOR DIAMETER 2.750 - 10 SPLINE - HUB NOT USED FOR SEAL - SPACER REQUIRED

HalfRound

FullRound

Flange TappedHoles

Non-TappedHoles

Yoke Series





RTO11709MLL

RTO14709MLL

MAJOR DIAMETER 2.343 - 45T INVOLUTE SPLINE - HUB DIAMETER AT OIL SEAL 3.750

HalfRound

FullRound

Flange TappedHoles

Non-TappedHoles

Yoke Series



X X 1610 1/2 - 20 TAPPED HOLES 86763 A-5263

X X 1710 86737 A-5122

X X 1710 1/2 - 20 TAPPED HOLES 86764 A-5264

X X 1760 1/2 - 20 TAPPED HOLES 5505521 A-5451

T8607A T8607B TX8607B

11


APPLICATION “6”

APPLICATION “7”

MAJOR DIAMETER 2.544 - 49T INVOLUTE SPLINE - HUB DIAMETER AT OIL SEAL 3.750

HalfRound

FullRound

Flange TappedHoles

Non-TappedHoles

Yoke Series



X X 1710 86738 A-5123

X X 1710 86741 A-5126

X X 1710 1/2 - 20 TAPPED HOLES 86775 A-5436

X X 1760 86740 A-5125

X X 1810 86742 A-5127

X X 1810 1/2 - 20 TAPPED HOLES 86774 A-5435

T-14607

MAJOR DIAMETER 2.250 - 10 SPLINE - HUB DIAMETER AT OIL SEAL 3.750

HalfRound

FullRound

Flange TappedHoles

Non-TappedHoles

Yoke Series



X X 1610 1/2 - 20 TAPPED HOLES 86747 A-5191

X X 1710 1/2 - 20 TAPPED HOLES 86748 A-5192

X X 1710 86753 A-5268

X X 1760 1/2 - 20 TAPPED HOLES 86772 A-5422

2A92 T14607A T14607B TX14607B RT6609A RT8609A

RT6610 RTO6610

12


APPLICATION “8”MAJOR DIAMETER 2.750 - 54T INVOLUTE SPLINE - NO SEAL

HalfRound

FullRound

Flange TappedHoles

Non-TappedHoles

Yoke Series



X X 1710 1/2 - 20 TAPPED HOLES 5505543

X 1710 5505544

X X 1760 1/2 - 20 TAPPED HOLES 5505545

X 1760 5505546

X X 1810 1/2 - 20 TAPPED HOLES 5505547

X 1810 5505548

X X RPL25 1/2 - 20 TAPPED HOLES 5505553

X X SPL170 M12 x 1.25 TAPPED HOLES 5505571

X X SPL250 M12 x 1.25 TAPPED HOLES 5505572

X X 92N 1/2 - 20 TAPPED HOLES 5505578

RT8908LL FRO12210B FR14210B FRO15210B RTO16210C RTLO16913A RTLO14918B

RTF8908LL FROF12210B FRF14210B FROF15210B RTOF16210C RTLOF16913A RTLOF14918B

RTO11908LL FRO12210C FRO14210C FRO15210C RTO11909MLL RTLO18913A RTLO16918B

RTOF11908LL FROF12210C FROF14210C FROF15210C RTOF11909MLL RTLOF18913A RTLOF16918B

RTO14908LL FR13210B RT14210B RTO15210C RTO14909MLL RT14915 RTLO18918B

RTOF14908LL FRF13210B RTF14210B RTOF15210C RTOF14909MLL RTF14915 RTLOF18918B

RTO16908LL FRO13210B RTO14210C FRO16210B RTLO12913A RTO14915 RTLO20918B

RTOF16908LL FROF13210B RTOF14210C FROF16210B RTLOF12913A RTOF14915 RTLOF20918B

FR12210B FRO13210C FR15210B FRO16210C RTLO14913A RTO16915

FRF12210B FROF13210C FRF15210B FROF16210C RTLOF14913A RTOF16915

13

Shipping WeightsShipping W

eights

Shipping Weights

ADD 50 POUNDS FOR SHIPPING MATERIALSAll weights are approximate

Model

Weight WithNo ClutchHousing

Weight WithCast IronHousing

Weight WithAluminumClutch Housing

14607 575 643 596

7608 597 665 618

8608 583 651 604

8908 690 758 711

11708 675 743 696

11908 690 758 711

14708 690 758 711

14908 690 758 711

16908 690 758 711

6609 376 444 397

8609 376 444 397

8709 581 649 602

12609 583 651 604

12709 583 651 604

13609 588 656 609

13709 588 656 609

14609 607 675 628

14709 607 675 628

16709 617 685 638

12210 592 660 613

12610 625 693 646

12710 606 674 627

13210 592 660 613

13610 625 693 646

13710 611 679 632

14210 592 660 613

14610 630 698 651

14710 624 692 645

Model

Weight WithNo ClutchHousing

Weight WithCast IronHousing

Weight WithAluminumClutch Housing

15210 602 670 623

16210 602 670 623

16610 630 698 651

16710 634 702 655

18610 630 698 651

11709MLL 671 739 692

11909MLL 671 739 692

14709MLL 673 741 694

14909MLL 673 741 694

12713 714 782 735

12913 714 782 735

14713 714 782 735

14913 714 782 735

16713 716 784 737

16913 716 784 737

18913 716 784 737

14715 696 764 717

14915 696 764 717

15715 696 764 717

16915 696 764 717

14718 716 784 737

14918 716 784 737

16718 716 784 737

16918 716 784 737

18718 716 784 737

18918 716 784 737

20918 716 784 737

14

Transmission Oil Capacities

Transmission Oil CapacitiesNote: These values are approximate—always use the fill hole

as the final reference.

Eaton® Fuller® Transmission Oil Capacities

Twin Countershaft Models Pints Liters

5 SPEEDS

905 22 10

11605 22 10

6 SPEEDS

955AL 25 12

906 26 12

1056AA 29 14

11606 26 12

7 SPEEDS

955ALL 28 13

8607 36 17

11607 36 17

14607 37 17

8 SPEEDS

1157DL 27 13

11607L 28 13

9508 25 12

11608 26 12

14608 28 13

9 SPEEDS

9509 25 12

11509 25 12

12509 25 12

1157DLL 29 14

6609 12 6

8609 15 7

8608L 27 13

9 SPEEDS – CONTINUED

11607LL 31 15

11707LL 28 13

11707DLL 28 13

13707DLL 28 13

13707MLL 28 13

11609 27 13

12609 27 13

13609 27 13

14609 27 13

11709 27 13

12709 27 13

13709 27 13

14709 27 13

16709 27 13

10 SPEEDS

958LL 28 13

1258LL 28 13

7608LL 19.5 9

11608LL 29 14

14608LL 29 13

11708LL 28 13

14708LL 29 14

8908LL 28 13

11908LL 28 13

14908LL 28 13

16908LL 28 13

12510 25 12

610 12 6

6610 12 6

910 25 12

1110 25 12


15

Transmission Oil CapacitiesOil Capacities


11610 26 12

12610 26 12

14610 26 12

RTLO-11610 28 13

RTLO-12610 28 13

RTLO-13610 28 13

RTLO-14610 28 13

RTLO-15610 28 13

RTLO-16610 28 13

11710 26 12

12710 26 12

13710 26 12

14710 26 12

15710 26 12

16710 26 12

FR-11210 23.5 11

FR-12210 23.5 11

FR-13210 23.5 11

FR-14210 23.5 11

FR-15210 23.5 11

FR-16210 23.5 11

11 SPEEDS

11709MLL 28 13

14709MLL 28 13

11909MLL 28 13

14909MLL 28 13

13 SPEEDS

12513 27 13

613 16 8

6613 16 8

9513 27 13



11613 29 14

14613 29 14

15613 29 14

RTLO-14613 28 13

RTLO-12713 28 13

RTLO-14713 28 13

RTLO-16713 28 13

RTLO-18913 28 13

15 SPEEDS

915 28 13

12515 28 13

11615 28 13

14615 30 14

15615 30 14

11715 28 13

14715 28 13

15715 28 13

14915 28 13

16915 28 13

18 SPEEDS

RTLO-14618 28 13

RTLO-16618 28 13

RTLO-14718 28 13

RTLO-16718 28 13

RTLO-18718 28 13

RTLO-20918 28 13


Copyright Eaton, 2013. Eaton hereby grant their customers, vendors, or distributors permission to freely copy, reproduce and/or distribute this document in printed format. It may be copied only in its entirety without any changes or modifications. THIS INFORMATION IS NOT INTENDED FOR SALE OR RESALE, AND THIS NOTICE MUST REMAIN ON ALL COPIES.

Note: Features and specifications listed in this document are subject to change without notice and represent the maximum capabilities of the software and products with all options installed. Although every attempt has been made to ensure the accuracy of information contained within, Eaton makes no representation about the completeness, correctness or accuracy and assumes no responsibility for any errors or omissions. Features and functionality may vary depending on selected options.

For spec’ing or service assistance, call 1-800-826-HELP (4357) or visit www.eaton.com/roadranger.In Mexico, call 001-800-826-4357.

Eaton Vehicle GroupP.O. Box 4013Kalamazoo, MI 49003 USA800-826-HELP (4357)www.eaton.com/roadranger

Printed in USA

Roadranger: Eaton and trusted partners providing the best products and services in the industry, ensuring more time on the road.

Date post:	29-Mar-2021
Category:	Documents
Upload:	others
View:	7 times
Download:	0 times

Fuller® Heavy-Duty Transmissions TRMT0951 EN-US...7. Identification chart for RT-8609, RT-7608LL,...

Documents