Date post: | 05-Apr-2018 |
Category: |
Documents |
Upload: | vishal-mohandas |
View: | 216 times |
Download: | 0 times |
of 190
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
1/190
Integrated Flight Deck
Cockpit Reference Guide
CessnaNav III
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
2/190
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
3/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III
Copyright 2004-2007 Garmin Ltd. or its subsidiaries. All rights reserved.
This manual reflects the operation of System Software version 0563.03 or later for Cessna 172R, 172S, 182T, T182T, 206H, and T206Haircraft. Some differences in operation may be observed when comparing the information in this manual to earlier or later softwareversions.
Garmin International, Inc., 1200 East 151st Street, Olathe, Kansas 66062, U.S.A.Tel: 913/397.8200 Fax: 913/397.8282
Garmin AT, Inc., 2345 Turner Road SE, Salem, OR 97302, U.S.A.Tel: 503/391.3411 Fax 503/364.2138
Garmin (Europe) Ltd., Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, Hampshire S051 9DL, U.K.Tel: 44/0870.851241 Fax: 44/0870.8501251
Garmin Corporation, No. 68, Jangshu 2nd Road, Shijr, Taipei County, TaiwanTel: 886/02.2642.9199 Fax: 886/02.2642.9099
Web Site Address: www.garmin.com
Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded orstored in any storage medium, for any purpose without the express written permission of Garmin. Garmin hereby grants permissionto download a single copy of this manual and of any revision to this manual onto a hard drive or other electronic storage medium tobe viewed for personal use, provided that such electronic or printed copy of this manual or revision must contain the complete textof this copyright notice and provided further that any unauthorized commercial distribution of this manual or any revision hereto isstrictly prohibited.
Garmin and G1000 are registered trademarks of Garmin Ltd. or its subsidiaries. FliteCharts, and SafeTaxi are trademarks of
Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin.
NavData is a registered trademark of Jeppesen, Inc.; Stormscope is a registered trademark of L-3 Communications; and XMis a registered trademark of XM Satellite Radio, Inc.; Honeywell and Bendix/King are registered trademarks of HoneywellInternational, Inc.; CO Guardian is a trademark of CO Guardian, Inc.
March 2007 190-00384-07 Rev. A Printed in the U.S.A.
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
4/190Garmin G1000 Cockpit Reference Guide for the Cessna Nav III 190-00384-07 Rev. A
WARNINGS,CAUTIONS, & NOTES
WARNING:Navigation and terrain separation must NOT be predicated upon the use of the terrain function.The G1000 Terrain Proximity feature is NOT intended to be used as a primary reference for terrain avoidance
and does not relieve the pilot from the responsibility of being aware of surroundings during flight. The TerrainProximity feature is only to be used as an aid for terrain avoidance and is not certified for use in applicationsrequiring a certified terrain awareness system. Terrain data is obtained from third party sources. Garmin isnot able to independently verify the accuracy of the terrain data.
WARNING:The displayed minimum safe altitudes (MSAs) are only advisory in nature and should not be reliedupon as the sole source of obstacle and terrain avoidance information. Always refer to current aeronauticalcharts for appropriate minimum clearance altitudes.
WARNING:The altitude calculated by G1000 GPS receivers is geometric height above Mean Sea Level and couldvary significantly from the altitude displayed by pressure altimeters, such as the GDC 74A Air Data Computer,or other altimeters in aircraft. GPS altitude should never be used for vertical navigation. Always use pressurealtitude displayed by the G1000 PFD or other pressure altimeters in aircraft.
WARNING:Do not use outdated database information. Databases used in the G1000 system must be updated
regularly in order to ensure that the information remains current. Pilots using any outdated database do soentirely at their own risk.
WARNING:Do not use basemap (land and water data) information for primary navigation. Basemap data isintended only to supplement other approved navigation data sources and should be considered as an aid toenhance situational awareness.
WARNING:Traffic information shown on the G1000 Multi Function Display is provided as an aid in visuallyacquiring traffic. Pilots must maneuver the aircraft based only upon ATC guidance or positive visual acquisitionof conflicting traffic.
WARNING:Use of the Stormscope is not intended for hazardous weather penetration (thunderstorm penetration).Stormscope information, as displayed on the G1000 MFD, is to be used only for weather avoidance, notpenetration.
WARNING:GDL 69 Weather should not be used for hazardous weather penetration. Weather information
provided by the GDL 69 is approved only for weather avoidance, not penetration.
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
5/190Garmin G1000 Cockpit Reference Guide for the Cessna Nav III190-00384-07 Rev. A
WARNINGS,CAUTIONS, & NOTES
WARNING:NEXRAD weather data is to be used for long-range planning purposes only. Due to inherent delaysin data transmission and the relative age of the data, NEXRAD weather data should not be used for short-range
weather avoidance.
WARNING:The Garmin G1000, as installed in Cessna Nav III aircraft, has a very high degree of functionalintegrity. However, the pilot must recognize that providing monitoring and/or self-test capability for allconceivable system failures is not practical. Although unlikely, it may be possible for erroneous operation tooccur without a fault indication shown by the G1000. It is thus the responsibility of the pilot to detect such anoccurrence by means of cross-checking with all redundant or correlated information available in the cockpit.
WARNING:For safety reasons, G1000 operational procedures must be learned on the ground.
WARNING:The United States government operates the Global Positioning System and is solely responsiblefor its accuracy and maintenance. The GPS system is subject to changes which could affect the accuracyand performance of all GPS equipment. Portions of the Garmin G1000 utilize GPS as a precision electronicNAVigation AID (NAVAID). Therefore, as with all NAVAIDs, information presented by the G1000 can be misusedor misinterpreted and, therefore, become unsafe.
WARNING:To reduce the risk of unsafe operation, carefully review and understand all aspects of the G1000Pilots Guide documentation. Thoroughly practice basic operation prior to actual use. During flight operations,carefully compare indications from the G1000 to all available navigation sources, including the informationfrom other NAVAIDs, visual sightings, charts, etc. For safety purposes, always resolve any discrepancies beforecontinuing navigation.
WARNING:The illustrations in this guide are only examples. Never use the G1000 to attempt to penetrate athunderstorm. Both the FAA Advisory Circular, Subject: Thunderstorms, and the Airmans Information Manual(AIM) recommend avoiding by at least 20 miles any thunderstorm identified as severe or giving an intenseradar echo.
CAUTION:The GDU 1040 and GDU 1044B PFD/MFD displays use a lens coated with a special anti-reflectivecoating that is very sensitive to skin oils, waxes, and abrasive cleaners. CLEANERS CONTAINING AMMONIA
WILL HARM THE ANTI-REFLECTIVE COATING. It is very important to clean the lens using a clean, lint-free clothand an eyeglass lens cleaner that is specified as safe for anti-reflective coatings.
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
6/190Garmin G1000 Cockpit Reference Guide for the Cessna Nav III 190-00384-07 Rev. A
WARNINGS,CAUTIONS, & NOTES
CAUTION:The Garmin G1000 does not contain any user-serviceable parts. Repairs should only be made byan authorized Garmin service center. Unauthorized repairs or modifications could void both the warranty and
the pilots authority to operate this device under FAA/FCC regulations.
NOTE:When using Stormscope, there are several atmospheric phenomena in addition to nearby thunderstormsthat can cause isolated discharge points in the strike display mode. However, clusters of two or more dischargepoints in the strike display mode do indicate thunderstorm activity if these points reappear after the screen hasbeen cleared.
NOTE:
All visual depictions contained within this document, including screen images of the G1000 panel anddisplays, are subject to change and may not reflect the most current G1000 system. Depictions of equipmentmay differ slightly from the actual equipment.
NOTE:This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received,including interference that may cause undesired operation.
NOTE:The GDU 1040 and GDU 1044B PFD/MFD may require a warm-up time of up to 30 minutes when exposedto -40C for an extended period. A warm-up time of up to 15 minutes may be required when exposed to -30C
for an extended period.
NOTE:This product, its packaging, and its components contain chemicals known to the State of California tocause cancer, birth defects, or reproductive harm. This notice is being provided in accordance with CaliforniasProposition 65. If you have any questions or would like additional information, please refer to our web site at
www.garmin.com/prop65.
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
7/190Garmin G1000 Cockpit Reference Guide for the Cessna Nav III190-00384-07 Rev. A RR-1
RECORD OF REVISIONS
Part Number Change Summary
190-00384-03
(Rev. A)
Added XM Radio and XM Weather
Added ADF capabilityAdded DME capabilityAdded BRG1/BRG2 pointersAdded dual audio panel operationAdded C172 parametersChanged Airspeed Trend VectorChanged Altitude Trend VectorAdded Checklist capabilityAdded Flight ID capability
190-00384-03(Rev. B)
Updated system software numbers
190-00384-04(Rev. A)
Reformatted manual to new formatAdded TAS capability
190-00384-04
(Rev. B)
Added DONE Softkey, XM-INFORMATION Page, and XM-RADIO
Page operation.
190-00384-05(Rev. A)
Added explanation of EIS display behavior upon exceedancesAdded better explanation of Intercom System IsolationAdded Stormscope operation upon loss of heading inputAdded TAWS-BAdded CO GuardianAdded new Fuel Totalizer
Updated G1000 System Messages
190-00384-06(Rev A)
Added GDU 7.00 (WAAS, VNAV & Charts) software parameters.Added AFCS for the 182 and 206Added database loading instructionsUpdated G1000 System MessagesCombined previous system software numbers into 0563.00
190-00384-07 Added GDU 8.02 parameters, Airways, and ADS-B
Revision Date of Revision Affected Pages Description
A March, 2007 i through Index-4 Production release
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
8/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III 190-00384-07 Rev. ARR-2
RECORD OF REVISIONS
Blank Page
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
9/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III190-00384-07 Rev. A i
TABLE OF CONTENTS
SECTION 1: SYSTEM OVERVIEW....................................1-11.1 PFD/MFD Controls...................................................1-21.2 PFD Softkeys............................................................1-51.3 MFD Softkeys ..........................................................1-81.4 MFD Page Groups ...................................................1-91.5 Vertical Navigation ..............................................1-101.6 Backlighting...........................................................1-121.7 XM Radio - Automatic Muting...........................1-121.8 Database Updates ................................................1-12
Jeppesen Aviation Database ...................................... 1-12Garmin Databases ..................................................... 1-13
SECTION 2: FLIGHT INSTRUMENTS..............................2-12.1 Airspeed Indicator..................................................2-3Speed Indication .........................................................2-3Speed Ranges ............................................................. 2-3Airspeed Trend Vector ................................................. 2-3Vspeed References ...................................................... 2-3
2.2 Attitude Indicator ..................................................2-32.3 Altimeter ..................................................................2-4
Altitude Reference Bug ................................................ 2-4
Altitude Trend Vector ................................................... 2-4Barometric Setting Box ................................................ 2-4Altitude Alerting .......................................................... 2-4Metric Display ............................................................. 2-5Low Altitude Annunciation ........................................... 2-5
2.4 Vertical Deviation/Glidepath/GlideslopeIndicator ...................................................................2-6
2.5 Marker Beacon Annunciations ............................2-7
2.6 Vertical Speed Indicator .......................................2-72.7 Barometric Altitude Minimums...........................2-72.8 Horizontal Situation Indicator (HSI)...................2-8
Course Pointer ............................................................ 2-9Course Deviation Indicator (CDI) .................................. 2-9Bearing Pointers and Information Windows ................ 2-11DME (optional) .......................................................... 2-11Navigation Source ..................................................... 2-11
2.9 Wind Data...............................................................2-122.10 Generic Timer ........................................................2-13
SECTION 3: ENGINE INDICATION SYSTEM (EIS)....3-13.1 Engine Display.........................................................3-13.2 Lean Display ............................................................3-4
Normally-aspirated Aircraft .......................................... 3-7
Turbocharged Aircraft ..................................................3-73.3 System Display........................................................3-7
SECTION 4: NAV/COM AND TRANSPONDER..........4-1
4.1 Radio Status Indications.......................................4-34.2 Volume ......................................................................4-34.3 Automatic Squelch.................................................4-34.4 Quickly Activating 121.500 MHz..........................4-34.5 Optional NAV Radios .............................................4-3
DME Radio (optional) .................................................. 4-3ADF Radio (optional) ................................................... 4-4
4.6 Frequency Auto-tuning .........................................4-4
Auto-tuning on the PFD ..............................................4-4Auto-tuning on the MFD .............................................4-44.7 Transponder .............................................................4-4
Mode Selection ...........................................................4-4Reply Status ................................................................4-5Code Selection ............................................................4-5Flight ID Reporting ......................................................4-6
SECTION 5: AUDIO PANEL ................................................5-1
5.1 COM Radio Selection .............................................5-25.2 Marker Beacon Receiver.......................................5-2
Marker Beacon Signal Sensitivity .................................5-25.3 Nav Radio Audio Selection...................................5-35.4 Intercom System (ICS) Isolation..........................5-35.5 Intercom Squelch Control.....................................5-45.6 Digital Clearance Recorder and Player .............5-4
SECTION 6: AUTOMATIC FLIGHT CONTROL.............6-16.1 AFCS Controls..........................................................6-16.2 Flight Director Operation.....................................6-2
Activating the Flight Director ....................................... 6-2Command Bars ...........................................................6-2AFCS Status Box .........................................................6-3
6.3 Flight Director Modes............................................6-3Pitch Modes ................................................................6-3Roll Modes................................................................6-17
6.4 Autopilot Operation ............................................6-22Flight Control ............................................................6-22Engaging the Autopilot..............................................6-22Control Wheel Steering..............................................6-23Disengaging the Autopilot ......................................... 6-23
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
10/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III 190-00384-07 Rev. Aii
TABLE OF CONTENTS
6.5 Example Procedures ............................................6-24Departure .................................................................6-24Intercepting a VOR Radial .......................................... 6-26Flying a Flight Plan/GPS Course ................................. 6-27
Descent ....................................................................6-28Approach .................................................................. 6-31Go Around/Missed Approach ..................................... 6-33
6.6 AFCS Annunciations and Alerts .........................6-34AFCS Status Alerts ..................................................... 6-34Overspeed Protection ................................................ 6-35
SECTION 7: NAVIGATION..................................................7-1
7.1 Navigation Map Page ............................................7-1Select the MAP Page Group ......................................... 7-17.2 Direct-to Navigation..............................................7-1
Direct-to Navigation from the MFD .............................. 7-1Direct-to Navigation from the PFD ............................... 7-3
7.3 Navigating an Example Flight Plan ....................7-57.4 Airport Information.............................................7-21
Select the Airport Information Page ...........................7-217.5 Intersection Information ....................................7-23
Select the Intersection Information Page .................... 7-237.6 NDB Information...................................................7-24
Select the NDB Information Page ............................... 7-247.7 VOR Information...................................................7-24
Select the VOR Information Page ............................... 7-247.8 User Waypoint Information Page .....................7-257.9 Nearest Airports ...................................................7-25
Nearest Airport Information on the MFD ....................7-25
Nearest Airports Information on the PFD ....................7-267.10 Nearest Intersections ..........................................7-26Select the Nearest Intersections Page ......................... 7-26
7.11 Nearest NDB ..........................................................7-27Select the Nearest NDB Page ..................................... 7-27
7.12 Nearest VOR...........................................................7-27Select the Nearest VOR Page .....................................7-27
7.13 Nearest User Waypoint........................................7-28Select the Nearest User Waypoint Page ...................... 7-28
7.14 Nearest Frequencies ............................................7-28Select the Nearest Frequencies Page .......................... 7-28
7.15 Nearest Airspaces.................................................7-29Select the Nearest Airspaces Page .............................. 7-29
SECTION 8: FLIGHT PLANNING......................................8-18.1 User Defined Waypoints........................................8-1
Select the User WPT Information Page ......................... 8-1Create User Waypoints from the Navigation Map Page . 8-2
8.2 Viewing the Active Flight Plan ............................8-28.3 Activate a Stored Flight Plan...............................8-28.4 Activate a Flight Plan Leg ....................................8-38.5 Stop Navigating a Flight Plan..............................8-38.6 Invert Active Flight Plan .......................................8-38.7 Create a New Flight Plan ......................................8-4
Create a New Flight Plan Using the MFD .....................8-4Create a New Flight Plan Using the PFD ......................8-4
8.8 Enter an Airway in a Flight Plan .........................8-58.9 Load a Departure ...................................................8-68.10 Load an Arrival........................................................8-68.11 Load an Approach ..................................................8-68.12 Remove a Departure, Arrival, or Approach
from a Flight Plan...................................................8-68.13 Store a Flight Plan..................................................8-68.14 Edit a Stored Flight Plan.......................................8-78.15 Delete a Waypoint from the Flight Plan............8-78.16 Invert and Activate a Stored Flight Plan ..........8-78.17 Copy a Flight Plan ..................................................8-78.18 Delete a Flight Plan ...............................................8-88.19 Graphical Flight Plan Creation ............................8-88.20 Trip Planning............................................................8-8
SECTION 9: PROCEDURES ................................................9-19.1 Arrivals and Departures........................................9-1
Load and Activate a Departure Procedure ....................9-1Load and Activate An Arrival Procedure ........................ 9-1
9.2 Approaches ..............................................................9-2Load and/or Activate an Approach Procedure ...............9-3Activate An Approach in the Active Flight Plan ............. 9-3
SECTION 10: HAZARD AVOIDANCE ...........................10-110.1 Customizing the Hazard Displays on the
Navigation Map ....................................................10-1
10.2 STORMSCOPE (Optional)..................................10-1Displaying Stormscope Lightning Data on theNavigation Map Page ................................................ 10-1Stormscope Page .......................................................10-2
10.3 XM Weather (Service Optional).........................10-3Displaying METAR and TAF information on the Airport
TABLE OF CONTENTS
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
11/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III190-00384-07 Rev. A iii
TABLE OF CONTENTS
Information Page ......................................................10-3Displaying Weather on the Weather Data Link Page ... 10-4Map Panning Information Weather Data Link Page . 10-5Weather Products & Symbols ..................................... 10-5
Weather Product Age ................................................ 10-610.4 Traffic Systems ......................................................10-7
Traffic Information Service (TIS) .................................. 10-7Traffic Advisory System (TAS) (Optional) ..................... 10-8ADS-B Traffic (Optional) ............................................. 10-9
10.7 Terrain and Obstacle Proximity.......................10-10Displaying Terrain and Obstacles on the TerrainProximity Page ........................................................ 10-10
Displaying Terrain and Obstacles on the NavigationMap ........................................................................10-11
10.8 Terrain Awareness & Warning System (TAWs)Display (Optional) ..............................................10-11Displaying Terrain on the TAWS Page ....................... 10-11Enable/Disable Aviation Data ................................... 10-12TAWS Inhibit ........................................................... 10-12Manual System Test ................................................. 10-13Forward Looking Terrain Avoidance (FLTA) ................ 10-13Premature Descent Alert (PDA) ................................ 10-13Excessive Descent Rate Alert (EDR) .......................... 10-14Negative Climb Rate After TakeoffAlert (NCR) .......... 10-14Five-Hundred Aural Alert ...................................... 10-14Displaying Terrain and Obstacles on the NavigationMap ........................................................................10-14Pop-up Alerts .......................................................... 10-15TAWS Alerts Summary ............................................. 10-16
Alert Annunciations ................................................. 10-17
SECTION 11: ABNORMAL OPERATION .....................11-111.1 Reversionary Mode ..............................................11-111.2 Abnormal COM Operation ..................................11-211.3 Unusual Attitudes.................................................11-211.4 Stormscope operation with loss of
Heading Input........................................................11-211.5 Hazard Displays with Loss of GPS Position ....11-2
11.6 Dead Reckoning....................................................11-3
SECTION 12: ANNUNCIATIONS & ALERTS..............12-112.1 Alert Level Definitions ........................................12-212.2 NAV III Aircraft Alerts ..........................................12-3
WARNING Alerts ....................................................... 12-3
CAUTION Alerts ........................................................12-3CAUTION Alerts (T182, T206, and 206 with PropDe-Ice Only) ..............................................................12-3Safe Operating Annunciation (T182, T206, and 206
with Prop De-Ice Only) ..............................................12-312.3 CO Guardian Messages .......................................12-312.4 AFCS Alerts (182 & 206 Only) .............................12-4
System Status Annunciation ....................................... 12-412.5 TAWS Alerts............................................................12-512.6 Other G1000 Aural Alerts....................................12-612.7 G1000 System Annunciations ............................12-712.8 G1000 System Message Advisories ..................12-9
MFD & PFD Message Advisories...............................12-10Database Message Advisories .................................. 12-11GMA 1347 Message Advisories ............................... 12-12GIA 63 Message Advisories ..................................... 12-13GIA 63W Message Advisories .................................. 12-15GEA 71 Message Advisories ....................................12-18GTX 33 Message Advisories.....................................12-18GRS 77 Message Advisories ..................................... 12-19GMU 44 Message Advisories ................................... 12-19GDL 69A Message Advisories .................................. 12-20GDC 74A Message Advisories .................................. 12-20Miscellaneous Message Advisories ........................... 12-20
INDEX ...................................................................................Index-1
TABLE OF CONTENTS
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
12/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III 190-00384-07 Rev. Aiv
TABLE OF CONTENTS
Blank Page
SECTION 1
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
13/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III190-00384-07 Rev. A 1-1
SYSTEM OVERVIEW
1-1
SECTION 1: SYSTEM OVERVIEW
The purpose of this Cockpit Reference Guide is
to provide the pilot a resource with which to findoperating instructions on the major features of theG1000 system more easily. It is not intended to be acomprehensive operating guide. Complete operatingprocedures for the complete system are found in theGarmin G1000 Pilots Guide for the Cessna Nav III (190-00498-02).
This guide gives the pilot abbreviated operatinginstructions for the Primary Flight Display (PFD), MultiFunction Display (MFD), and the GMA 1347 Audio Panel
System.
NOTE:The pilot should read and thoroughlyunderstand the Cessna Pilots OperatingHandbook (POH) for limitations, procedures andoperational information not contained in thisCockpit Reference Guide. The Cessna POH alwaystakes precedence over the information found in
this guide.
SECTION 1
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
14/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III 190-00384-07 Rev. A1-2
SYSTEM OVERVIEW
1.1 PFD/MFD CONTROLS
Figure 1-1 PFD/MFD Controls
421 65 7 983
17
12
13
11
10
27
25
24
28
182 & 206 Only
16
15
14
20
21
19
23
18
22
26
29
SECTION 1SYSTEM OVERVIEW
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
15/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III190-00384-07 Rev. A 1-3
SYSTEM OVERVIEW
PFD and MFD controls function the same.
1 NAV VOL/ID Knob Controls the NAV audiolevel. Press to turn the Morse code identifier ONand OFF. Volume level is shown in the field as apercentage.
2 NAV Frequency Transfer Key Transfers thestandby and active NAV frequencies.
3 Dual NAV Knob Tunes the MHz (large knob)and kHz (small knob) standby frequencies forthe NAV receiver. Press to switch the tuning box(light blue box) between the NAV1 and NAV2fields.
4 Heading Knob Turn to manually select a headingon the HSI. When pressed, it synchronizesthe heading bug with the compass lubber line.Selected Heading provides the heading referenceto the Flight Director while operating in HeadingSelect Mode.
5 Joystick Changes the map range (distance top tobottom of map display) when rotated. Activatesthe map pointer when pressed.
6 CRS/BARO Knob The large knob sets the
altimeter barometric pressure and the smallknobadjusts the course. The course is only adjustablewhen the HSI is in VOR1, VOR2, or OBS/SUSPMode. Pressing this knob centers the CDI on thecurrently selected VOR. Selected Course providescourse reference to the Flight Director whenoperating in Navigation and Approach Modes.
7 Dual COM Knob Tunes the MHz (large knob)and kHz (small knob) standby frequencies for theCOM transceiver. Pressing this knob switches thetuning box (light blue box) between the COM1and COM2 fields.
8 COM Frequency Transfer Key Transfers thestandby and active COM frequencies. Pressingand holding this key for two seconds automatically
tunes the emergency frequency (121.5 MHz) inthe active frequency field.
9 COMVOL/SQ Knob Controls COM audio level.Pressing this knob turns the COM automaticsquelch ON and OFF. Audio volume level isshown in the field as a percentage.
10 Direct-to Key Allows the user to enter adestination waypoint and establish a direct courseto the selected destination (specified by theidentifier, chosen from the active route, or takenfrom the map pointer position).
11 FPL Key Displays the active Flight Plan Page for
creating and editing the active flight plan, or foraccessing stored flight plans.
12 CLR Key (DFLT MAP) Erases information,cancels an entry, or removes page menus. Todisplay the Navigation Map Page immediately,press and hold CLR(MFD only).
13
Dual FMS Knob Used to select the page tobe viewed (only on the MFD). The largeknobselects a page group (MAP, WPT, AUX, NRST),while the smallknob selects a specific page withinthe page group. Pressing the smallknob turns theselection cursor ON and OFF. When the cursoris ON, data may be entered in the different fieldsusing the small and largeknobs. The largeknobis used to move the cursor on the page, while thesmallknob is used to select individual charactersfor the highlighted cursor location. When theG1000 displays a list that is too long for thedisplay screen, a scroll bar appears along the right
SECTION 1SYSTEM OVERVIEW
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
16/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III 190-00384-07 Rev. A1-4
SYSTEM OVERVIEW
side of the display, indicating the availability ofadditional items within the selected category.Press the small FMS Knob to activate the cursor
and turn the large FMS Knob to scroll through thelist.
14 MENU Key Displays a context-sensitive listof options. This list allows the user to accessadditional features, or to make setting changesthat relate to certain pages.
15
PROC Key Selects approaches, departures andarrivals from the flight plan. If a flight plan isused, available procedures for the departure and/or arrival airport are automatically suggested. Ifa flight plan is not used, the desired airport andthe desired procedure may be selected. This keyselects IFR departure procedures (DPs), arrivalprocedures (STARs) and approaches (IAPs) fromthe database and loads them into the active flightplan.
16 ENT Key Accepts a menu selection or dataentry. This key is used to approve an operationor complete data entry. It is also used to confirmselections and information entries.
17 Dual ALT Knob Sets the selected altitude inthe box located above the Altimeter. The largeknob selects the thousands, while the smallknobselects the hundreds. Altitude Select is used bythe Automatic Flight Control System in certainmodes, in addition to the standard G1000 AltitudeAlerter function.
18 AP Key (182 & 206 only) Engages/disengagesthe Autopilot and Flight Director. Pressing theAP Key activates the Flight Director and engagesthe Autopilot in the default pitch axis and roll axis
modes. Pressing theAP Key again disengages theautopilot and deactivates the Flight Director.
19 HDG Key (182 & 206 only) Selects/deselectsthe Heading Select Mode.
20 NAV Key (182 & 206 only) Selects/deselects theNavigation Mode.
21 APR Key (182 & 206 only) Selects/deselects theApproach Mode.
22 VS Key (182 & 206 only) Selects/deselects theVertical Speed Mode.
23 FLC Key (182 & 206 only) Selects/deselects theFlight Level Change Mode.
24 FD Key (182 & 206 only) Activates/deactivatesthe Flight Director only. Pressing the FD Key
turns on the Flight Director in the default pitchaxis and roll axis modes. Pressing the FD Keyagain deactivates the Flight Director and removesthe command bars, unless the Autopilot isengaged. If the Autopilot is engaged, the FD Keyis disabled.
25
ALT Key (182 & 206 only) Selects/deselects theAltitude Hold Mode.
26 VNV Key (182 & 206 only) Selects/deselectsVertical Navigation Mode.
27 BC Key (182 & 206 only) Selects/deselects BackCourse Mode.
28 29 NOSE UP/NOSE DN Keys (182 & 206only) Controls the active pitch reference forthe Pitch Hold, Vertical Speed, and FlightLevel Change Modes.
SECTION 1SYSTEM OVERVIEW
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
17/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III190-00384-07 Rev. A 1-5
SYSTEM OVERVIEW
1.2 PFD SOFTKEYS
Softkey OFFSoftkey ON
Figure 1-2 PFD Top Level Softkeys
Press the BACK orOFF Softkey
to return to the top-level softkeys.
ALERTSSTRMSCP
DME ALERTS
Figure 1-3 INSET Softkeys
INSET Press to display the Inset Map in the lowerleft corner of the PFD.
OFF Press to remove the Inset Map.DCLTR(3) Press momentarily to select the desired
amount of map detail. The declutter level appearsadjacent to the DCLTRSoftkey.
- No declutter: All map features are visible.- Declutter 1: Declutters land data.- Declutter 2: Declutters land and SUA data.
- Declutter 3: Declutters large NAV dataremaining (removes everything except theactive flight plan).
TRAFFIC Press to display traffic on the map.
TOPO Press to display topographical data (i.e.,coastlines, terrain, rivers, lakes, etc.) and
elevation scale on the Inset Map.TERRAIN Press to display terrain information onthe Inset Map.
STRMSCP (optional) Press to display theStormscope lightning data on the Inset Map(within a 200 nm radius of the aircraft).
NEXRAD (optional) Press to display NEXRADweather and coverage information on the Inset
Map.XM LTNG (optional) Press to display XM lightning
information on the Inset Map.BACK Press to return to the previous level softkey
configuration.
SECTION 1SYSTEM OVERVIEW
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
18/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III 190-00384-07 Rev. A1-6
SYSTEM OVERVIEW
Figure 1-4 PFD Configuration Softkeys
Press the STD BARO orBACK Softkey to return tothe top-level softkeys
BRG1 (NAV1)
BRG1 (GPS)
BRG1 (OFF)
DME ALT UNIT
METERS IN HPA
DME ALERTS
ALERTS
ALERTS
ALERTS
HSI FRMT
ALERTSARC HSI360 HSI
BRG1 (ADF)
BRG2 (NAV2)
BRG2 (GPS)
BRG2 (OFF)
BRG2 (ADF)
PFD Press to display the additional softkeys for
additional configuration of the PFD.DFLTS Press to reset default settings on the PFD.WIND Displays softkeys to select wind data
parameters. OPTN 1 Longi tudina l and la tera l
components. OPTN 2 Total direction and speed.
OPTN 3 Total direction with headwind andcrosswind speed components. OFF Information not displayed.DME (optional) Press to display the DME
Information Window.BRG1 (bearing) Press to cycle through the
following Nav sources, making the pointer theindicator for the corresponding source anddisplaying the appropriate information.
NAV1 Displays NAV1 waypoint frequency oridentifier and DME information in the BRG1Information Window.
GPS Displays GPS waypoint identifier and GPS
distance information in the BRG1 InformationWindow.
ADF Displays ADF in the BRG1 InformationWindow.
OFF Removes the BRG1 InformationWindow.
HSI FRMT Press to display the HSI formatting
softkeys. 360 HSI Press to display the HSI in a 360
degree format. ARC HSI Press to display the HSI in an arc
format.
BRG2 (bearing) Press to cycle through thefollowing Nav sources, making the pointer the
indicator for the corresponding source anddisplaying the appropriate information.
NAV2 Displays NAV2 waypoint frequency oridentifier and DME information in the BRG2Information Window.
SECTION 1SYSTEM OVERVIEW
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
19/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III190-00384-07 Rev. A 1-7
SYSTEM OVERVIEW
GPS Displays GPS waypoint identifier and GPSdistance information in the BRG2 Information
Window.
ADF Displays ADF in the BRG2 InformationWindow. OF F Removes the BRG2 Information
Window.ALT UNIT Displays softkeys for setting the
altimeter and BARO settings to metric units: METERS When enabled, displays altimeter in
meters.
IN Press to display the BARO setting as inchesof mercury.
HPA Press to display the BARO setting ashectopacals.
STD BARO Press to set the barometric pressureto standard pressure.
BACK Press to return to the previous level softkeys.
ALERTS Press to display the Alerts Window.OBS Press to select OBS Mode on the CDI when
navigating by GPS (only available with active leg).CDI Press to change navigation mode on the CDI
between GPS, VOR1, and VOR2.DME (optional) Press to display the DME Tuning
Window.
Press the BACK Softkey to return
to the top-level softkeys.
Press the IDENT orBACK Softkey to return
to the top-level softkeys.
ALERTS
ALERTS
DME ALERTS
Figure 1-5 XPDR (Transponder) Softkeys
XPDR Press to display the transponder modeselection softkeys.STBY Press to select Standby Mode.
ON Press to select Mode A.ALT Press to select Altitude Reporting Mode.GND Press to select Ground Mode.VFR Press to automatically squawk 1200 (only
in the U.S.A., refer to ICAO standards for VFRcodes in other countries).
CODE Press to display transponder code selectionsoftkeys 0-7.
0 through 7 Press numbers to enter code.
IDENT Press to provide special aircraftposition identification to Air Traffic Control(ATC).
BKSP Press to remove numbers entered oneat a time.
BACK Press to return to the previous levelsoftkeys.
IDENT Press to provide special aircraft positionidentification to Air Traffic Control (ATC).
BACK Press to return to the previous levelsoftkeys.
ALERTS Press to display the Alerts Window.
SECTION 1SYSTEM OVERVIEW
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
20/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III 190-00384-07 Rev. A1-8
IDENT Press to provide special aircraft positionidentification to Air Traffic Control (ATC).
TMR/REF Press to display the Timer/ReferencesWindow.
NRST Press to display the Nearest AirportsWindow.
ALERTS Press to display the Alerts Window.
1.3 MFD SOFTKEYS
ENGINE Pressing this softkey makes available the LEANand SYSTEM Softkeys which in turn access the Lean
Page and the System Page, respectively.
Figure 1-6 MFD Softkeys
BACKRST FUELSYSTEMENGINE LEAN
ENGINE MAP DCLTR
BACKSYSTEMLEANENGINE
ENGINE LEAN BACKSYSTEM
Press the ENGINE orBACK Softkey to
return to the default Engine Page level.
TRAFFIC TOPO BACKTERRAIN
DCLTR-2
DCLTR-3
DCLTR-1
Press the BACK Softkey on this
level to return to the top softkey level.
CHKLIST
ASSISTCYL SLCT EXIT EMERGCYENGINE DONE
The DONE Softkey changes to UNDO when the checklist
item is already checked.
(optional)
BACK-10 GALSYSTEMENGINE LEAN
GAL REM
-1 GAL XX GAL+10 GAL+1 GAL XX GAL
Press the ENGINE Softkey to
the default Engine Page level.
X = airframe specific values
STRMSCP NEXRAD XM LTNG
(optional) (optional)(optional)
SHW CHRT
(optional)
AIRWAYS
AIRWY LO
AIRWAY HI
AIRWY ON
(Default softkey
is dependant on
the selection made
in the map setup
options)
Press the BACK Softkey to return
to the previous softkey level.
MAP Pressing this softkey enables the followingsoftkeys:TRAFFIC Pressing this softkey displays/removes
Traffic on the Navigation Map.
TOPO Pressing this softkey displays or removestopographic information on the Navigation Map.
TERRAIN Pressing this softkey displays/removesterrain and obstacle data on the Navigation Map.
SECTION 1SYSTEM OVERVIEW
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
21/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III190-00384-07 Rev. A 1-9
AIRWAYS Pressing this softkey displays/removesairways information. The default is dependent onmap setup option selected. Pressing cycles through
all airways displayed (AIRWY ON
), low altitudeairways only (AIRWY LO), and high altitude airwaysonly (AIRWY HI).
STRMSCP (optional) Pressing this softkey displays/removes Stormscope lightning data on the NavigationMap.
NEXRAD (optional) Pressing this softkey displays/removes precipitation data on the Navigation Map.
XM LTNG (optional) Pressing this softkey displays/removes XM Radio lightning data on the NavigationMap.
BACK Pressing this softkey displays the ENGINE andMAP top level softkeys.
DCLTR (declutter) Pressing this softkey removes mapinformation in three levels.
CHKLIST (checklist)(optional) Pressing the CHKLISTSoftkey displays the Checklist Page.ENGINE Displays engine softkeys.DONE Pressing this softkey checks off a checklist item.
If an item is already checked, an UNDO Softkey willbe displayed.
EXIT Press to exit the checklist.EMERGCY Pressing this softkey displays the
emergency checklist.
Figure 1-7 Page Group Icon
Map Page Group
Waypoint Page Group
Auxiliary Page Group
Nearest Group
Selected Page
Number of Pages in CurrentGroup
1.4 MFD PAGE GROUPS
1) Turn the large FMS Knob until the desired pagegroup is selected.
2) Turn the small FMS Knob to select pages withinthe group. See Figure 1-7.
SECTION 1SYSTEM OVERVIEW
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
22/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III 190-00384-07 Rev. A1-10
1.5 VERTICAL NAVIGATION
In WAAS capable installations, one of two altitudesources is used by the G1000 when giving vertical
navigation guidance. WAAS GPS altitude is used whengiving guidance for a WAAS approach. Baro correctedaltitude is used when vertical guidance is given in all othersituations and in non-WAAS systems.
The G1000 system can use altitude constraintsassociated with lateral waypoints to give guidance forvertical navigation. These altitudes are, depending on the
specific instance, entered by the pilot or retrieved from thepublished altitudes in the navigation database.
The navigation database only contains altitudesfor procedures that call for Cross at altitudes. If theprocedure states Expect to cross at, then the altitude willnot be in the database. In this case the altitude may beentered manually.
NOTE: All arrival procedure altitudes contained inthe navigation database are for turbojet aircraft only.Alter or enter altitudes as desired to comply with theATC clearance.
When activating or loading an arrival or approachprocedure into an active flight plan, the VNV ALT fields
will be populated with any altitudes that can be retrievedfrom the navigation database.
Since altitudes loaded with an arrival procedure arepublished only for turbojet aircraft, the altitudes aredisplayed as white text indicating that the altitudes aredisplayed for reference only. An arrival waypoint altitudemay be used (or designated) as is, or changed to a
different altitude. An altitude is designated by pressing theFMS Knob and turning the large FMS Knob to place thecursor on the desired altitude and pressing the ENT Key orentering a different value and pressing the ENT Key. Thealtitude will now be displayed as light blue text, indicating
that the altitude is now designated to give vertical speedand deviation guidance.
Approach waypoint altitude constraints are designated
in the same way as previously described for arrivals. Thesealtitudes will also be displayed as light blue text after beingdesignated for use. Waypoint altitude constraints maybe designated up to, but not including the FAF. The FAFwill always be a reference only altitude and cannot bedesignated, unless the selected approach does not providevertical guidance. In this case, the FAF altitude can bedesignated.
Altitudes that have been designated for use in verticalguidance may also be made non-designated by placing thecursor over the desired altitude and pressing the CLRKey.Other displayed altitudes may change due to re-calculationsor rendered invalid as a result of manually changing analtitude to a non-designated altitude.
To help interpret the meanings of how the altitudes are
presented, keep the following points in mind: When the altitude is displayed in light blue,
the system is using that altitude (designated) todetermine vertical speed and deviation guidance.
When the altitude is displayed in white, it is not beingused by the system (non-designated) to determinethe vertical speed and deviation guidance.
An altitude displayed as small text is an altitude thatis published in the navigation database. Altitudes displayed as a light blue subdued text
cannot be used in the current vertical navigationcalculations.
SECTION 1SYSTEM OVERVIEW
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
23/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III190-00384-07 Rev. A 1-11
White Text Light Blue Text Light Blue Subdued Text
Large Text Altitude calculated by the systemestimating the altitude of the
aircraft as it passes over thenavigation point. This altitudeis provided as a reference andis not designated to be used indetermining vertical speed anddeviation guidance.
Altitude has been entered by thepilot. Altitude is designated for
use in giving vertical speed anddeviation guidance. Altitude doesnot match the published altitudein navigation database or nopublished altitude exists.
The system cannot use this altitudein determining vertical speed and
deviation guidance.
Small Text Altitude is not designated to
be used in determining verticalspeed and deviation guidance.Altitude has been retrieved fromthe navigation database and isprovided as a reference.
Altitude is designated for use in
giving vertical speed and deviationguidance. Altitude has beenretrieved from the navigationdatabase or has been entered bythe pilot and matches a publishedaltitude in the navigation database.
The system cannot use this altitude
in determining vertical speed anddeviation guidance.
Table 1-1 VNV Altitude Text Size and Color
Refer to Figure 1-8 and Table 1-1 for more detailregarding the significance of text size and color.
Figure 1-8 VNAV Altitudes
Large LightBlue Text
Small WhiteText withAltitude
RestrictionBar
Large White
Text
Small LightBlue Subdued
Text
Small LightBlue Text
Some altitudes retrieved from the database haveassociated restrictions indicating to stay At, At or Above,or At or Below a specific altitude. These restrictions areindicated using a bar above and/or below the appropriatealtitude as shown in Figure 1-9.
Stay AT or ABOVE 5,000 ft
Stay AT or BELOW 3,000 ft
Stay AT 2,300 ft
Figure 1-9 Altitude Restrictions
See Section 7 - Navigation, for a sample flight planwhich further illustrates vertical navigation in moredetail.
SECTION 1SYSTEM OVERVIEW
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
24/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III 190-00384-07 Rev. A1-12
1.6 BACKLIGHTING
Manually adjust the backlight for the PFD
and MFD:1) Press the MENU Key on the PFD to display the
PFD Setup Menu window.
2) Press the small FMS Knob to activate the cursor.PFD DSPL > AUTO is now highlighted.
3) Turn the small FMS Knob to display theselection window.
4) Turn the FMS Knob to select MANUAL, thenpress the ENT Key.
5) With the intensity value now highlighted, turnthe small FMS Knob to select the desiredbacklighting.
6) Turn the large FMS Knob to highlight MFD DSPL
> AUTO and repeat steps 3 through 5.
Figure 1-10 PFD Setup Menu Window
1.7 XM RADIO - AUTOMATIC MUTING
XM Radio audio will be automatically muted when theaircraft groundspeed exceeds approximately 30 kts andthe airspeed is less than approximately 80 kts. The audiomust be manually unmuted once the aircraft is outsidethe applicable speed range. Refer to the G1000 OptionalEquipment section of the pilots guide.
1.8 DATABASE UPDATES
The G1000 System uses Secure Digital (SD) cards toload and store various types of data. For basic flight op-
erations, SD cards are required for database storage as wellas Jeppesen aviation and ChartView database updates.
The following procedures pertain to updating theG1000 system with SD cards obtained as outlined in
Appendix B of the G1000 Cessna Nav III Pilots Guide.
Jeppesen Aviation Database
NOTE: After the aviation database is installed,the card may be removed after loading theupdate to each LRU.
Updating the Jeppesen aviation database:
1) With the G1000 System OFF, insert the SD cardcontaining the aviation database update into thetop card slot of the PFD to be updated (Label ofSD card facing left).
2) Turn the G1000 System ON. A prompt similar tothe following is displayed in the upper left cornerof the PFD:
Figure 1-11 Database Update Prompt
3) Press the ENT Key to start the database update.A prompt similar to the following is displayed:
SECTION 1SYSTEM OVERVIEW
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
25/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III190-00384-07 Rev. A 1-13
Figure 1-12 Database Update Confirmation
4) After the update completes, the PFD starts innormal mode.
5) Turn the G1000 System OFF and remove the SDcard.
6) Repeat steps 1 through 4 for the MFD. The MFDand PFD databases are now updated. Removethe SD card when finished.
7) Verify that the correct update cycle is loadedduring startup of the MFD.
Garmin Databases
Since these databases are not stored internally in theMFD or PFD, a Supplemental Data Card containing iden-tical database versions must be kept in each display unit.
NOTE: The data contained in the terrain andobstacle databases comes from governmentagencies. Garmin accurately processes andcross-validates the data, but cannot guaranteethe accuracy and completeness of the data.
1) Insert one SD card in the bottom card slot ofthe MFD and one in the bottom card slot of thePFD. The SD card containing the ChartView orFliteCharts database must be inserted into thebottom slot on the MFD.
2) Apply power to the G1000 System. View theMFD power-up splash screen. Check that thedatabases are initialized and displayed on thescrolling window of the splash screen. Whenupdating the terrain and FliteCharts databases,an in progress message may be seen. If thismessage is present, wait for the system to finishloading before verifying the correct databasesare initialized, then proceed to step 3.
Figure 1-13 Power-Up Splash Screen Window
3) Acknowledge the Power-up Page agreement bypressing the ENT Key or the right most softkey.
4) At the MAP NAVIGATION MAP Page, select
the MAP Softkey and check to make sure thatthe TOPO and TERRAIN Softkeys are available(not dimmed) and other database features arefunctioning.
5) Power down the G1000.
SECTION 1SYSTEM OVERVIEW
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
26/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III 190-00384-07 Rev. A1-14
Blank Page
SECTION 2FLIGHT INSTRUMENTS
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
27/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III190-00384-07 Rev. A 2-1
SECTION 2: FLIGHT INSTRUMENTS
The following discussions pertain to the Primary Flight
Display, unless otherwise indicated.
7 8
12
1516
9
14
13
6
3
4
2
1 17
Figure 2-1 Default PFD Information
15
16
12
14
13
10
7
4
2
6
178
3
1 NAV Frequency Box
Airspeed Indicator
True Airspeed Box
Outside Air Temperature Box
Altitude Reference Box
Horizontal Situation Indicator
Heading Box
System Time Box
Transponder Status Box
Barometric Setting Box
Vertical Speed Indicator
Altimeter
COM Frequency Box
Navigation Status Box
11
9
Slip/Skid Indicator
Turn Rate Indicator
11
10
18
18 Attitude Indicator
5
5 Ground Track Bug
SECTION 2FLIGHT INSTRUMENTS
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
28/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III 190-00384-07 Rev. A2-2
Figure 2-2 Additional PFD Information
2
1
5
3
4
8
6
Traffic Annunciation
2
4
3
1
Selected Heading Box
9 Flight Plan Window
10 Barometric Minimums Box
8 BRG2 Information Window
Vspeed References
5
Vertical Deviation/Glidepath (WAAS en-abled systems only)/Glidesope Indicator
14
Inset Map
Wind Data Window
BRG1 Information Window
Altitude Reference Bug11
6
13 Barometric Minimums Bug
15 Marker Beacon Annunciation
12 Selected Course Box
7
7 DME Information Window
10
9
12
14
13
11
15
Figure 2-3 PFD Navigation Status Box
Active Flight Plan Leg Distance to NextWaypoint Bearing to NextWaypoint
SECTION 2FLIGHT INSTRUMENTS
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
29/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III190-00384-07 Rev. A 2-3
2.1 AIRSPEED INDICATOR
Figure 2-4 Airspeed Indicator
Actual Airspeed
True AirspeedBox
Airspeed TrendVector
Speed Ranges
VspeedReferences
Speed Indication
The indicated airspeed is displayed inside the blackpointer. The pointer will become red upon reaching
Vne.
Figure 2-5 Red Pointer at Vne
Speed Ranges
The color coded speed range strip denotes flapsoperating range, normal operating range, and neverexceed speed (Vne). A red range is also present for lowspeed awareness. Refer to the Pilots Operating Handbook(POH) for airspeed limitations and indicator markings.
Airspeed Trend Vector
The end of the trend vector displays approximately
what the airspeed will be in 6 seconds if the current rateof acceleration/deceleration is maintained.
Vspeed References
Vspeed References are turned on or off in theTimer/References Window. Press the TMR/REF Softkey
to display the widow. When active (ON), the Vspeeds aredisplayed at their respective locations to the right of theairspeed scale. To activate the Vspeed References, displaythe Timer/Reference Window and turn the large FMSKnob to place the cursor in the ON/OFF field. Turn thesmall FMS Knob to select ON or OFF.
2.2 ATTITUDE INDICATOR
Figure 2-6 Attitude Indicator
3
2
1
9
8
7
6
5
4
1
2
3
4
5
Roll Scale
Horizon Line
Aircraft Symbol
Land Representation
Roll Pointer 6
7
8
9
Aircraft Wing Tips
Pitch Scale
Sky Representation
Slip/Skid Indicator
Roll Index Zero10
10
The Slip/Skid Indicator is located under the roll pointerand moves laterally away from the pointer to indicatelateral acceleration. One Slip/Skid indicator displacementis equal to one ball displacement when compared to atraditional slip/skid indicator.
SECTION 2FLIGHT INSTRUMENTS
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
30/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III 190-00384-07 Rev. A2-4
2.3 ALTIMETER
AltitudeReference
Box
AltitudeTrendVector
CurrentAltitude
BarometricSetting
Box
AltitudeReference
Bug
Figure 2-7 Altimeter
BarometricAltitude
Minimums Bug
Altitude Reference Bug
The Altitude Reference Bug is displayed at the SelectedAltitude or the edge of the tape (whichever is closer to thecurrent altitude) to provide increased altitude awarenessand to set the desired hold altitude for the autopilot.
Set the Altitude Reference Bug: Turn the ALT Knobs to set the Altitude Reference
Bug. The small ALT Knob sets the hundreds andthe large ALT Knob sets the thousands. Thisaltitude also appears in the Altitude ReferenceBox above the Altimeter.
Altitude Trend Vector
The end of the trend vector displays approximatelywhat the altitude will be in six seconds if the current rate
of vertical speed is maintained.
Barometric Setting Box
Select barometric pressure:
1) Turn the BARO Knob to select the desiredsetting.
2) Push the BARO Knob to select standardpressure.
Altitude Alerting
Figure 2-8 Altitude Alerting Visual Annunciations
Within 1000 ft Within 200 ft Deviation of 200 ft
Visual annunciations appear in the Altitude ReferenceBox. Whenever the setting is changed, the Altitude
Alerter is reset. The Altitude Alerter is independent of theAutomatic Flight Control System.
SECTION 2FLIGHT INSTRUMENTS
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
31/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III190-00384-07 Rev. A 2-5
Metric Display
Display altitude in meters and barometricpressure in hectopascals:
1) Press the PFD Softkey to display the second levelsoftkeys.
2) Press the ALT UNIT Softkey.
3) Press the METERS Softkey to display altitude inmeters.
4) Press the HPA Softkey to display the barometric
setting in hectopascals. Press the IN Softkeyto display the barometric setting in inches ofmercury.
5) Press the BACK Softkey to return to the previouslevel softkeys.
Figure 2-9 Altimeter (Metric)
Low Altitude Annunciation
NOTE:The LOW ALT annunciation is only availablein G1000 systems configured with WAAS-capableGPS. Also, the LOW ALT annunciation is notavailable when the G1000 is configured withTAWS (Terrain Awareness & Warning System),unless TAWS is inhibited.
When the Final Approach Fix (FAF) is the activewaypoint in a GPS WAAS approach using vertical guidance,a LOW ALT (Low Altitude) annunciation may appear ifthe current aircraft altitude is at least 164 feet below theprescribed altitude at the FAF. The annunciation initiallyflashes. After a few seconds the flashing stops and theannunciation is displayed as shown in Figure 2-10.
Figure 2-10 Low Altitude on GPS Approach
Low AltitudeAnnunciation
SECTION 2FLIGHT INSTRUMENTS
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
32/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III 190-00384-07 Rev. A2-6
2.4 VERTICAL DEVIATION/GLIDEPATH/GLIDESLOPE INDICATOR
The Vertical Deviation and Required Vertical Speed
Indicators appear when vertical guidance is being givenprior to executing an approach (see Figure 2-11). Insystems that are WAAS enabled, the Glidepath Indicatorappears at a point prior to the FAF when executing an LPVor LNAV+V approach (see Figure 2-12).
Figure 2-11 Vertical Deviation Indications
VerticalDeviationIndicator
VNAVTarget
Altitude
RequiredVertical
Speed
Figure 2-12 Glidepath Indicator
GlidepathIndicator
The Glideslope Indicator appears when an ILS approachhas been activated and an ILS is tuned in the active NAV
receiver field (see Figure 2-13).
Figure 2-13 Glideslope Indicator
Marker BeaconAnnunciation
GlideslopeIndicator
SECTION 2FLIGHT INSTRUMENTS
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
33/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III190-00384-07 Rev. A 2-7
2.5 MARKER BEACON ANNUNCIATIONS
Figure 2-14 Marker Beacon Annunciations
Outer Marker Middle Marker Inner Marker
Altimeter
2.6 VERTICAL SPEED INDICATOR
Figure 2-15 Vertical Speed Indicator
Vertical Speed Pointer
Vertical Speed Bug
Selected Vertical Speed
The actual vertical speed is displayed inside the
pointer.When the Flight Director is placed in Vertical Speed
Mode (by pressing the VS Key) the Vertical Speed Bugis displayed. Press the NOSE UP or NOSE DN Key toadjust.
2.7 BAROMETRIC ALTITUDE MINIMUMS
The desired barometric altitude minimums can be set inthe Timer/References Window. The altitude ranges from 0
to 16,000 feet in 10-foot increments. The minimums arereset anytime the power is cycled.
Figure 2-16 Barometric Minimum Descent Altitude Settings
The desired barometric minimum descent altitude(MDA, or Decision Height, DH) can be set in the Timer/References Window.
Visual annunciations alert the pilot when approachingthe MDA:
When the aircraft altitude descends to within 2500feet of the MDA setting, the Barometric MinimumBox appears with the altitude in light blue text.
The bug appears on the tape in light blue once inrange.
When the aircraft passes through 100 feet of theMDA, the bug and text turn white.
Once the aircraft descends past the MDA, the bugand text turn yellow and the aural alert, MinimumsMinimums, is generated.
Alerting is inhibited while the aircraft is on the ground.If the aircraft climbs after having reached the MDA, once itreaches 50 feet above the MDA, alerting is disabled.
SECTION 2FLIGHT INSTRUMENTS
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
34/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III 190-00384-07 Rev. A2-8
Within 100 ft
Altitude Reached
Within 2500 ft
Figure 2-17 Barometric Minimum Descent Altitude
Alerting Visual Annunciations
BarometricMinimum Box
BarometricMinimum Bug
Set the barometric altitude minimums:
1) From the Timer References Window, turn the largeFMS Knob to highlight the BARO MIN field.
2) Turn the small FMS Knob to select the desired
barometric altitude minimums and press the ENTKey. The ON/OFF field is now highlighted.
3) Turn the small FMS Knob in the direction of thegreen arrowhead.
2.8 HORIZONTAL SITUATION INDICATOR(HSI)
The HSI compass can be displayed as a 360 rose or140 arc by pressing the PFD Softkey, followed by the360 HSI or theARC HSI Softkey. Figure 2-18 Horizontal Situation Indicator
9
15
10
7
6
5
4
3
1
8
14
13
12
11
Heading Bug
3
4
7
5
6
8
1 Turn Rate Indicator
Navigation Source
Course Deviation Indicator
TO/FROM Indicator
Course Pointer
Rotating Compass Rose
12
11
13
14
15
10
9
OBS Mode
Lateral Deviation Scale
Flight Phase
Aircraft Symbol
Lubber Line
Heading
Turn Rate and Heading Trend Vector
2
2 Ground Track Bug
SECTION 2FLIGHT INSTRUMENTS
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
35/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III190-00384-07 Rev. A 2-9
Turn Rate Indicator and Heading Trend VectorTick marks to the left and right of the lubber line
denote half-standard and standard turn rates. A magentaturn rate trend vector shows the current turn rate. Theend of the trend vector gives the heading predicted in sixseconds, based on the present turn rate. At rates greaterthan 4 deg/sec, an arrowhead appears at the end of themagenta trend vector and the prediction is no longervalid.
Figure 2-20 Standard-Rate Turn Indication
Turn RateTrend Vector(standard rate)
Figure 2-19 Turn Rate Indicator and Trend Vector
Half-Standard TurnRate Tick Mark
Standard TurnRate Tick Mark
Turn Rate
Trend Vector(rate > 4deg/sec)
Course Pointer
The course pointer is a single line arrow (GPS, VOR1
and LOC1) or double line arrow (VOR2 and LOC2) whichpoints in the direction of the set course.
Figure 2-21 Course Pointer
Course Deviation Indicator (CDI)
The CDI scale automatically adjusts to the currentphase of flight as seen in Figure 2-22. Scaling may be
selected manually from the MFD System Setup Page.
Flight Phase Automatic CDI Full-scaleDeflection
Departure (DRPT) 0.3 nm
Terminal (TERM) 1.0 nm
Enroute (ENR) 2.0 nm
Oceanic (OCN) 2.0 nmApproach (LNAV) 1.0 nm decreasing to 350 feet
depending on variables (see Figure2-23)Approach (LNAV+V)
Approach (LNAV/VNAV)(WAAS only)
1.0 nm decreasing to a specifiedcourse width, then 0.3 nm,
depending on variables (see Figure
2-24)
Approach
(LPV)(WAAS only)Missed Approach 0.3 nm
SECTION 2FLIGHT INSTRUMENTS
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
36/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III 190-00384-07 Rev. A2-10
2.0nm
Enroute(Oceanic if >200 nmfrom nearest airport)
0.3
nm
MissedApproach
1.0nm
Approach
1.0nm
Terminal
1.0nm
Terminal
0.3
nm
Departure
CDIFull-sca
leDeflection
31nmf
romD
estinationAirp
ort
30nmf
romD
epartureAirport
Refer to accompanyingapproach CDI scaling figures
Drawing not to scale
Figure 2-22 Phases of Flight/CDI Scaling
1.0nm
2 nm
350ft
angle setby system
0.3nm
FAF
CDIFull-scaleDeflection CDI scale is set to the smaller of 0.3 nm
or an angle set by the system
CDI scale varies if Vectors-To-Final is activatedDrawing not to scale
Figure 2-23 Typical LNAV and LNAV+V Approach CDI Scaling
1.0nm
2 nmFAF
0.
3nm
coursewidth
Landing
Threshold
CDIFu
ll-scaleDeflection
angle basedon databaseinformation
CDI scale varies if Vectors-To-Final is activatedDrawing not to scale
Figure 2-24 Typical LNAV/VNAV and LPV Approach CDI Scaling(WAAS Systems Only)
SECTION 2FLIGHT INSTRUMENTS
i i d f i i d
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
37/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III190-00384-07 Rev. A 2-11
Bearing Pointers and Information Windows
Pressing the PFD Softkey provides access to the BRG1and BRG2 Softkeys. The BRG1 pointer is a single line
pointer. The BRG2 pointer is a double line pointer. Pressthe BRG1 or BRG2 Softkey to cycle through selectingNAV1/2, GPS, or ADF for display using the correspondingpointer.
Bearing 2Pointer
Bearing 1Information
Window
Bearing 1Pointer
Bearing 2Information
Window
Figure 2-25 HSI with Bearing Information
DMEInformation
Window CDI
Distance to
Bearing Source
WaypointIdentifier
BearingSource
PointerIcon
Figure 2-26 BRG1 Information Window
Distance toBearing Source
WaypointIdentifier
PointerIcon
BearingSource
Figure 2-27 BRG2 Information Window
DME (optional)
To display the DME Information Window, press the
PFD Softkey followed by the DME Softkey.
Figure 2-28 DME Information Window
Navigation SourceChange CDI navigation sources:
1) Press the CDI Softkey to change from GPS toVOR1/LOC1.
2) Press the CDI Softkey again to change fromVOR1/LOC1 to VOR2/LOC2.
3) Press the CDI Softkey a third time to return toGPS.
When using GPS as the navigation source, the followingmay appear:
LOI - GPS position integrity is inadequate for thecurrent procedure being flown. If GPS is being usedas primary navigation, and LOI is annunciated, other
means of primary navigation will be required, suchas VHF. LOI is also displayed during GPS positioninitialization.
WARN GPS detects a position error.
SECTION 2FLIGHT INSTRUMENTS
SUSP Di l d h i OBS M d i di i 2 9 WIND DATA
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
38/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III 190-00384-07 Rev. A2-12
SUSP Displayed when in OBS Mode indicatingGPS waypoint sequencing is suspended.
DR Navigating using Dead Reckoning due to anerror in the GPS solution.
Figure 2-29 GPS LOI, GPS SUSP, LOC1 and VOR2
Enable/disable OBS Mode while navigating
with GPS:
1) Press the OBS Softkey to select OBS Mode.
2) Turn the CRS Knob to select the desired courseto/from the waypoint.
3) Press the OBS Softkey again to disable OBSMode.
NOTE:TheOBSSoftkey is only displayed whennavigating an active leg using GPS.
2.9 WIND DATA
When the window is selected for display, but windinformation is invalid or unavailable, the window shows
NO WIND DATA. Wind data can be displayed in threedifferent ways:
Longitudinal and lateral components (Option 1) Total wind direction and speed (Option 2) Total direction with head and crosswind speed
components (Option 3)
Option 1 Option 2
Option 3 No Data
Figure 2-30 Wind Data Window
Displaying wind data:
1) Press the PFD Softkey.
2) Press the WIND Softkey to display wind data
below the Selected Heading.3) Press one of the OPTN softkeys to change how
wind data is displayed.
4) To remove the Wind Data Window, press the OFFSoftkey.
SECTION 2FLIGHT INSTRUMENTS
2 10 GENERIC TIMER
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
39/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III190-00384-07 Rev. A 2-13
2.10 GENERIC TIMER
Figure 2-31 Timer Status Prompts
Change the Generic Timer:1) Press the TMR/REF Softkey, then turn the large
FMS Knob to select the time field (hh/mm/ss).Turn the FMS Knobs to set the desired time, thenpress the ENT Key. The UP/DOWN field is nowhighlighted.
2) Turn the small FMS Knob to display the UP/DOWN
window. Turn the FMS Knob to select UP orDOWN, then press the ENT Key. START? isnow highlighted.
3) Press the ENT Key to START, STOP, or RESET thetimer (if the timer is counting DOWN, it must bereset manually). Press the CLR Key or the TMR/REFSoftkey to remove the window.
SECTION 2FLIGHT INSTRUMENTS
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
40/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III 190-00384-07 Rev. A2-14
Blank Page
SECTION 3 ENGINEINDICATION SYSTEM (EIS)
SECTION 3: ENGINE INDICATION
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
41/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III190-00384-07 Rev. A 3-1
SECTION 3: ENGINE INDICATIONSYSTEM (EIS)
NOTE:Refer to the Pilots Operating Handbook(POH) for limitations.
EIS information is presented in three displays, accessedusing the ENGINE Softkey on the MFD:
Engine Display Default display, shows all criticalengine, fuel, and electrical indicators
Lean Display Provides engine leaninginformation
System Display Shows numeric readouts ofcritical engine, fuel, and electrical indicators
Green and white bands indicate normal ranges ofoperation; yellow and red bands indicate caution andwarning, respectively. If sensory data to an instrumentbecomes invalid or unavailable, a red X is shown acrossthe instrument.
3.1 ENGINE DISPLAY
The Engine Display is the default EIS display and canbe displayed after viewing other EIS displays by pressingthe ENGINE softkey.
The EIS automatically defaults back to the EngineDisplay from the Lean or System Display when certainparameters are exceeded. Fluctuations in engine speedand fuel quantity above certain levels, depending on theairframe, also cause reversion back to the Engine Display.
1 Engine Manifold Pressure Gauge (MAN IN)Models 182T, T182T, 206H, T206H Displays
engine power in inches of mercury (in Hg).Turbocharged aircraft have a red portion of thegauge indicating the maximum manifold pressurerange. A white tick mark is displayed indicatingthe cruise manifold pressure (Model T182T only).
2 Tachometer (RPM) Shows propeller speedsin revolutions per minute (rpm). Red rangeindicates propeller overspeed warning; a white
high-rpm range indicates above normal operatingspeeds (Models 172S, 206H, and T206H)
3 Fuel Flow Indicator (FFLOW GPH) Showsthe current fuel flow in gallons per hour (gph).For turbocharged aircraft, the indicator displaysa small stand-alone green band indicatingmaximum takeoff fuel flow. A white tick mark
indicates the maximum cruise fuel flow (ModelT182T only).
4 Oil Pressure Indicator (OIL PRES) Displayspressure of the oil supplied to the engine inpounds per square inch (psi).
5 Oil Temperature Indicator (OIL TEMP)
Displays the engine oil temperature in degreesFahrenheit (F).
6 Cylinder Head Temperature Indicator (CHT)Models 182T, T182T, 206H, T206H Showsthe head temperature of the hottest cylinder(number shown in triangular pointer) in degreesFahrenheit (F).
7 Exhaust Gas Temperature Indicator (EGT)
Normally-aspirated Aircraft Displays theexhaust gas temperature of the hottest cylinder(number shown in triangular pointer) in degreesFahrenheit (F).
8 Turbine Inlet Temperature Indicator (TIT)
Turbocharged Aircraft Displays the temperatureat the turbine inlet in degrees Fahrenheit (F).
9 Vacuum Pressure Indicator (VAC) Models172R and 172S Displays vacuum pressure.
SECTION 3 ENGINEINDICATION SYSTEM (EIS)
l d ( ) l ( ) l h
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
42/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III 190-00384-07 Rev. A3-2
10 Fuel Quantity Indicator (FUEL QTY GAL) Shows the quantity of fuel in the tanks, ingallons, ranging from zero to full (F) for each fuel
tank (leftL and rightR). When full, the indicatordisplays to 35 gallons per side (26 gallons for theModels 172R and 172S).
11 Engine Hours (Tach) (ENG HRS) Models 172Rand 172S A numeric readout gives the time (inhours) the engine has been in service.
Figure 3-1 Engine Display (Normally-aspirated Aircraft)
Model 206H
12
10
13
1
5
4
3
2
6
7
Model 172R
9
2
3
4
5
7
13
10
12
11
Model 172S
9
2
3
4
5
7
13
10
12
11
Model 182T
7
6
2
3
4
5
1
13
10
12
12 Voltmeter (M, E BUS VOLTS) Displays themain and essential bus voltages.
13 Ammeter (M, S BATT AMPS) Shows themain and standby battery load in amperes.
SECTION 3 ENGINEINDICATION SYSTEM (EIS)
Cruise
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
43/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III190-00384-07 Rev. A 3-3
Figure 3-2 Engine Display (Turbocharged Aircraft)
Model T206H
MaximumTakeoff Fuel
Flow
8
6
2
3
4
5
1
13
10
12
Model T182T
CruiseFuel Flow
ManifoldPressure
8
6
2
3
4
5
1
13
10
12
SECTION 3 ENGINEINDICATION SYSTEM (EIS)
3.2 LEAN DISPLAY for the selected cylinder to be displayed below
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
44/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III 190-00384-07 Rev. A3-4
NOTE:The pilot should follow the engine man-
ufacturers recommended leaning procedures inthe Pilots Operating Handbook (POH).
1 Engine Manifold Pressure Gauge (MAN IN)Models 182T, T182T, 206H, T206H Displaysengine power in inches of mercury (in Hg).Turbocharged aircraft have a red portion of thegauge indicating the maximum manifold pressure
range. A white tick mark is displayed indicatingthe cruise manifold pressure (Model T182 only).
2 Tachometer (RPM) Shows propeller speedsin revolutions per minute (rpm). Red rangeindicates propeller overspeed warning; a whitehigh-rpm range indicates above normal operatingspeeds (Models 172S, 206H and T206H).
3 Fuel Flow (FFLOW GPH) Shows the currentfuel flow in gallons per hour (gph).
4 Turbine Inlet Temperature Indicator(TIT) Models T182T and T206H Displaysthe temperature at the turbine inlet in degreesFahrenheit (F). When the ASSIST Softkey is
pressed, the TIT deviation from peak (PEAK) isdisplayed below the indicator.
5 Exhaust Gas Temperature Bar Graph (EGT
F) Displays the exhaust gas temperature of allcylinders in degrees Fahrenheit (F); a readoutfor the selected cylinder (by default, the hottest
cylinder) is shown below the bar graph. Theselected cylinder is indicated in light blue.Cylinders whose EGTs are in the normal rangeappear in white. Pressing the ASSIST Softkeycauses the EGT deviation from peak (PEAK)
y p ythe indicator.
6 Cylinder Head Temperature Indicator (CHT)
Shows the head temperatures of all cylindersin degrees Fahrenheit (F); a readout for theselected cylinder (by default, the hottest cylinder)is shown below the bar graph. The selectedcylinder is indicated in light blue. Cylinderswhose CHTs are in the normal range appear inwhite. Cylinders whose CHTs enter the cautionand warning ranges appear in yellow and red,
respectively.
7 Fuel Quantity Indicator (FUEL QTY GAL)
Shows the quantity of fuel in the left and rightfuel tanks (leftL and rightR). When full, theindicator displays to 35 gallons per side (26gallons for the Models 172R and 172S).
SECTION 3 ENGINEINDICATION SYSTEM (EIS)
1
2 21
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
45/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III190-00384-07 Rev. A 3-5
Figure 3-3 Lean Display (Normally-aspirated Aircraft)
Model 206H
6
3
2
5
7
Hollow BlockRepresents
Peak
Model 172R
7
2
3
6
5
Model 172S
2
5
3
7
6
Model 182T
6
3
2
5
7
SECTION 3 ENGINEINDICATION SYSTEM (EIS)
1Cruise
Manifold1
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
46/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III 190-00384-07 Rev. A3-6
Model T206H
6
3
4
2
5
7
ManifoldPressure
Model T182T
6
3
4
2
5
7
Figure 3-4 Lean Display (Turbocharged Aircraft)
The Lean Display is accessed by pressing the ENGINESoftkey followed by the LEAN Softkey and providesinformation for performing engine leaning.
From the Lean Display, the pilot can utilize the CYLSLCT andASSIST softkeys to obtain information aboutspecific cylinders. Pressing the CYL SLCT (CylinderSelect) Softkey cycles through the cylinders (i.e., changesthe cylinder indicated on the bar graphs in light blue).This softkey is disabled when the ASSIST Softkey ispressed or when a cylinder experiences a caution orwarning condition; the softkey remains disabled until thetemperature returns to normal.
SECTION 3 ENGINEINDICATION SYSTEM (EIS)
The ASSIST Softkey aids in the leaning process byid if i h k f h fi li d h
The System Display is accessed by pressing theENGINE S f k f ll d b h SYSTEM S f k d
7/31/2019 G1000 CessnaNavIII CockpitReferenceGuide SystemSoftwareVersion0563.03orlater
47/190
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III190-00384-07 Rev. A 3-7
identifying the peak of the first cylinder whose temperaturefalls. If the temperature of the peaked cylinder exceedsthe peak value, the peak value is not updated. Press the
ASSIST Softkey to stop peak monitoring.
Normally-aspirated Aircraft
For normally-aspirated aircraft, when a cylinder peaks,its peak is represented by a hollow block on the EGT BarGraph. The EGT readout for the peaked cylinder, indicat-ed on the bar graph in light blue, appears directly beneath
the bar graph. The system automatically switches to thefirst peak obtained and displays the temperature deviationfrom peak (PEAK) in degrees Fahrenheit (F) below theEGT readout.
Turbocharged Aircraft
Leaning for turbocharged aircraft is done with refer-ence to the Turbine Inlet Temperature (TIT). When thetemperature peaks, the numeric readout (PEAK) appearsbelow the TIT Indicator and displays the difference be-tween peak and current TITs, in degrees Fahrenheit (F).If a peak is not displayed, underscores are shown untilone is established.
3.3 SYSTEM DISPLAY
NOTE:Fuel calculations do not use the aircraftfuel quantity indicators and are calculated fromthe last time the fuel was reset.
NOTE: The pilot should refer to the PilotsOperating Handbook (POH) for fuel values and
limitations. The displayed fuel remaining can beadjusted up to 53 gal (Models 172R, 172S) or 87gal (Models 182T, T182T, 206H, T206H).
ENGINE Softkey followed by the SYSTEM Softkey andshows critical engine, fuel, and electrical parameters.
Fuel calculations are based on the fuel flow totalizer
and the displayed fuel remaining, adjusted by the pilotusing the following softkeys:
RST FUEL Resets totalizer-based fuel remaining(GAL REM) to zero and the fuel used (GAL USED)to zero
GAL REM Gives access to softkeys for adjustingthe amount of fuel remaining for purposes of fuel
calculations
Fuel remaining can be adjusted in one or ten-gallonincrements using the appropriate softkeys. Softkeys alsoallow entering the full tank quantity for the aircraft or thetab quantity, which is 35 gallons (Models 172R and 172S)or 64 gallons (Models 182T, T182T,