SamsungGalaxyS5DisplayAssemblyReplacement
WerxParts www.werxparts.com Page1of12
Samsung Galaxy S5 Display Assembly Replacement
INTRODUCTION Use this guide along with the Werx Repair Mat to replace the cracked or broken screen on your Samsung Galaxy S5. Use this guide to replace the display assembly, which includes the front glass,
digitizer, and home button cable.
TOOLS: IMPORTANT Take your time! The repair takes about 15-25 minutes.
Remember that you will be handling fragile parts, so be gentle!
No screws are removed during this repair.
Werx Repair Mat
SamsungGalaxyS5DisplayAssemblyReplacement
WerxParts www.werxparts.com Page2of12
Step 1: Rear Case
• Before disassembling your phone, be
sure it is powered off.
• Insert a fingernail or a plastic opening
tool into the divot to the left of the rear-
facing camera.
• Gently pry and twist the flexible rear
cover off the back of the phone.
Step 2: Battery
• Insert a fingernail or plastic opening
tool into the recess in the bottom right
corner of the battery and lift upward.
• Remove the battery away from the
phone.
SamsungGalaxyS5DisplayAssemblyReplacement
WerxParts www.werxparts.com Page3of12
Step 3: Display Assembly
• Use a plastic opening tool to pry up the
plastic midframe connector panel.
• Remove the connector panel with a pair
of tweezers.
Step 4:
• Use the sharp tip of a spudger to pry
the home button connector straight up
off its socket.
SamsungGalaxyS5DisplayAssemblyReplacement
WerxParts www.werxparts.com Page4of12
Step 5:
• Use the heat gun at the lowest setting
to heat the frame/border of the phone.
When using the heat gun, be careful
not to leave it heating in one area for
too long. Constantly move the heat gun
when using it.
Step 6:
• Insert the metal spudger underneath
the midframe and the front glass.
SamsungGalaxyS5DisplayAssemblyReplacement
WerxParts www.werxparts.com Page5of12
Step 7:
• Slide the metal spudger to release the
adhesive.
• If you find any kind of resistance
remember to reheat as needed for
easier separation.
Step 8:
• Apply heat to the topside of the device
near the ear speaker.
• Slide the metal spudger across the top
of the device, being very careful not to
insert the pick too deeply.
SamsungGalaxyS5DisplayAssemblyReplacement
WerxParts www.werxparts.com Page6of12
Step 9:
• If you encounter any resistance from
cooling adhesive, reheat the area for
easier separation.
• Slide the metal spudger down along the
left half of the phone stopping at the
lower left corner.
Step 10:
• Slide the metal spudger all the way to
the bottom left corner of the phone.
Step 11:
SamsungGalaxyS5DisplayAssemblyReplacement
WerxParts www.werxparts.com Page7of12
• The bottom end of the phone contains
the soft button and home button ribbon
cables. If you insert the metal spudger
too far into the phone you risk cutting
these cables.
• Slide the metal spudger across the
bottom edge of the display to separate
the last of the remaining adhesive.
Step 12:
• If the front panel is not easily freed, the
adhesive on the soft button cable may
need to be separated.
• These cables are thin and easily
damaged, therefore be certain you are
only peeling them off the display
assembly and not lacerating them.
• Insert metal spudger under the soft button icons on the display and pry the button cables
down off the inside of the front panel.
SamsungGalaxyS5DisplayAssemblyReplacement
WerxParts www.werxparts.com Page8of12
Step 13:
• Slightly lift, but do not remove, the
home button end of display assembly.
• Do not remove the front panel entirely.
It is still attached by a connector.
Step 14:
• Use the sharp tip of a spudger to lift the
front panel assembly cable connector
straight up off its socket on the
motherboard.
• Safely remove the front panel assembly
from phone.
SamsungGalaxyS5DisplayAssemblyReplacement
WerxParts www.werxparts.com Page9of12
Step 15:
• Remove the protective plastic from the
back of the new LCD assembly.
Step 16:
• Insert the LCD to the front panel
assembly.
Make sure flex cables are properly
aligned before snapping back in place
and gently push on connections until
they connect.
SamsungGalaxyS5DisplayAssemblyReplacement
WerxParts www.werxparts.com Page10of12
Step 17:
• Fold the LCD back to the midframe of
the device.
• Run your fingers along the sides being
sure the assembly slips evenly into the
frame.
Step 18:
• Connect the home button to the back of
the logic board.
SamsungGalaxyS5DisplayAssemblyReplacement
WerxParts www.werxparts.com Page11of12
Step 19:
• Insert the plastic midframe connector
panel.
Step 20:
• Insert the battery making sure there is a
proper connection.
SamsungGalaxyS5DisplayAssemblyReplacement
WerxParts www.werxparts.com Page12of12
Step 21:
• Insert the rear cover and run your
fingers along the sides being sure it sits
evenly into the frame.