Date post: | 23-Jul-2016 |
Category: |
Documents |
Upload: | tom-knoblock |
View: | 220 times |
Download: | 3 times |
Brite Energy Solutions - Tom Knoblock - 1-844-533-2897
Light Module ——LED Optical Engine
GAMA Series
LED Area Light
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLATION
IMPORTANT INSTALLATION INFORMATION
1.Before commencing installa�on or maintenance, ensure electricity is switched off at the mains. Installa�on or maintenance should be carried out by a qualified electrician.
2.The luminaire must not, under any circumstances, be installed directly to flammable materials, and luminaires must not be covered with any flammable materials.
3.Moun�ng height range of 6 to 12 meters, this model is suitable for outdoor ligh�ng.
4.Ensure there is adequate free air circula�on of at least 50cm around the luminaire. All luminaires run hot. It is the installer's responsibility to consider fire risk and takeappropriate precau�ons.
Model No.
FLB80-T
FLB120-T
No. of LEDs
36
54
System Wa�age
80W
120W
Dimensions (L x W x H)
360(14.17")x330(12.99")x70mm(12.76")
Net Weight Working Environment
6.87kg(15.11lbs.)
Main specifica�ons:
Input Voltage:120-277V~50/60Hz
-40℃-+50℃FLB160-T 72 160W 8.38kg(18.44lbs.)
FLB200-T 90 200W 9.25kg(20.35lbs.)
FLB240-T 108 240W 10.21kg(22.46lbs.)
5.88kg(12.94lbs.)
ARRLUXHuizhou Arrlux Optoelectronic Co.,Ltd
420(16.53")x330(12.99")x70mm(12.76")
480(18.90")x330(12.99")x70mm(12.76")
600(23.61")x330(12.99")x70mm(12.76")
660(26.00")x330(12.99")x70mm(12.76")
EPA* IP
IP65
0.034m²
0.037m²
0.041m²
0.048m²
0.052m²
The ingress protec�on of the fixture is IP65 if the mains supply cable's specifica�on is H07RN-F 3*1.5m㎡.
Model No.
FLC80-T
FLC120-T
No. of LEDs
36
54
System Wa�age
80W
120W
Dimensions (L x W x H)
360(14.17")x330(12.99")x70mm(12.76")
Net Weight Working Environment
6.87kg(15.11lbs.)
Input Voltage:347-480V~50/60Hz
-40℃-+50℃FLC160-T 72 160W 8.38kg(18.44lbs.)
FLC200-T 90 200W 9.25kg(20.35lbs.)
FLC240-T 108 240W 10.21kg(22.46lbs.)
5.88kg(12.94lbs.)
420(16.53")x330(12.99")x70mm(12.76")
480(18.90")x330(12.99")x70mm(12.76")
600(23.61")x330(12.99")x70mm(12.76")
660(26.00")x330(12.99")x70mm(12.76")
EPA* IP
IP65
0.034m²
0.037m²
0.041m²
0.048m²
0.052m²
The ingress protec�on of the fixture is IP65 if the mains supply cable's specifica�on is H07RN-F 3*1.5m㎡.
INSTALLATION INFORMATION
L
W W
Safety No�ce
WIRING INSTRUCTION Alterna�ng Current
Terminal Block
LIVE
GROUND
NEGATIVE
LIVE - Black
NEGATIVE - White
GROUND-Housing
LED D
rivER
Main
s po
wer su
pp
ly
Electrical Connec�ons
L
G
N
Input wire H07RN-F 3x1.5mm² (SJOW 3 * 18AWG) or rubber sheathed cable (not supplied).Conductor must have a minimum cross-sec�onal area of 1.0mm² (18AWG).
STEP I: Connect the LINE wire in the mains power supply cord to black LINE wire from lightbody .
STEP II: Connect the NEUTRAL wire in the mains power supply cord to white NEUTRAL wire from lightbody .
STEP II I: Connect the green grounding wire in the mains power supply cord to green grounding wire from lightbody .
***IF THERE IS JUNCTION BOX IN CEILING:
7
STEP 1: 1.Loosen the M12 screws, nuts, spring washers on the moun�ng arm with a wrench.2.Insert the pole into the middle hole of moun�ng arm �ll to the end.See Figure 1.
STEP 2:When the pole is inside the moun�ng arm, adjust the moun�ng angle of the lamp, then screw the the M12 screws, nuts and spring washers.See Figure 2
21
LEAVE A COPY FOR THE USER / MAINTENANCE ENGINEER FOR FUTURE REFERENCE
This logo indicates that this product must not be disposed of with other waste.
Please recycle used lamps to prevent environmental hazard and threats to human
health resul�ng from improper disposal.
Installa�on Instruc�on & Installa�on Steps
Pole
Spring washer(M10)
Moun�ng arm
STEP 7: Reference “Electrical Connec�ons” sec�on for comple�ng electrical connec�ons. See Figure 7
STEP 3: 1. Fix the moun�ng plate on the pole with M10 screws.2. Connect the cables from the luminaire and from the pole. Please See figure 3 the wiring diagram.
STEP 4:1. Fix the luminaire to the moun�ng plate with 4 M6*20 screws.See Figure 4
43
Installa�on and Moun�ng A
M10 screw
M6 screw
Pole Moun�ng plate
Installa�on and Moun�ng A
Installa�on and Moun�ng B Installa�on and Moun�ng B
STEP 5: 1. Fix the moun�ng plate on the wall with M10 screws.2. Connect the cables from the luminaire and from the wall. Please See figure 5 the wiring diagram.
5
Wall
M10 screw
M6 screw
Moun�ng plate
STEP 6:1. Fix the luminaire to the moun�ng plate with 4 M6*20 screws.See Figure 6
6
Wall
Installa�on and Moun�ng C Installa�on and Moun�ng C
Moun�ng arm
Spring washer(M10)
Pole