1
2201 GARDNER-DENVER PUMPS • RIG COMPONENTS • AJAX S PUMPS TUFF-BREED® PARTS • MAYHEW 19 RIGS TRAVELING BLOCKS HOOK-BLOCK COMBINATIONS TRAVELING BLOCKS Gardner-Denver engineers have achieved a new ratio of weight to rated capacity. This has added up to 2,000 pounds of additional weight over competitive designs without increasing outside dimensions. The result is a low center of gravity block that falls faster and straighten Fabricated sheaves, precision balanced, provide smooth operation and are used in all sizes and in match- ing crown blocks. HOOK-BLOCK COMBINATIONS Gardner-Denver Trim-True blocks may be ordered with your choice of unitized hook. Com- pletely built in to provide a single short block assembly, it saves valuable space in short masts. The block case has been carefully designed with countersunk bolts, pins and sheave guards. The teardrop housing has smooth rounded edges and recessed bolts and pins. FABRICATED SHEAVES Wire line groove is flame-hardened to retain shape to prolong wire line life. Large diameter sheaves. Uni- form in cross section and precision balanced. HEAVY DUTY BEARINGS Double row tapered roller bearings hold sheaves in alignment. Designed for radial and thrust loads. INDIVIDUAL LUBRICATION All sheaves can be lubricated from either side of block by their individual grease fittings. EASILY REMOVABLE SHEAVE GUARDS Heavy duty sheave guards are fastened to side plates by through-pins which can be easily removed for reaving. SMOOTH TEARDROP HOUSING Teardrop shaped housing has recessed bolts and pins as well as smoothly rounded edges. Side plates are from heavy steel plate re-enforced at the pin for extra strength HEAVY STEEL CLEVIS PLATE Plate clevis is designed to permit raising of block to vertical while hook is still on floor. Heavy construction provides high strength in clevis and pins. SIMPLE BAIL LOCK PIN Bail is easily removed and assembled by removing tapered threaded pin which is recessed in clevis. No large wrench nuts or hammer nuts to remove. TRAVELING BLOCK SPECIFICATIONS MODEL Depth Rating Rated Capacity No. o) Sheaves Dia. ol Sheaves Sheave Grooves A B C D DD E F G Weight ft. m. ton Kg. in. mm. in. in. mm. in. mm. in. mm. in. mm. in. mm. in. mm. in. mm. in. mm. ib. Kg. 55 T-660 15,000 + 4,572 t 550 498,952 6 60 1,524 1%, 1 1 /20r1 3 /8 112% 2,858 10'/4 267 13 330 34 864 63 1,600 100 2,540 15 381 4 102 18,000 8.165 40 T-650 10-20,000 3,048-6,096 400 362,874 6 50 1,270 1 3 /8 or 1 1 /4 95% 2.416 9ta 234 12V4 311 31% 806 52</2 1,334 83 6 /4 2,124 13 330 4 102 14,000 6,350 30 T-542 8-14,000 2,438-4,267 300 272,155 5 42 1,067 1 1 /«or1 1 /S 78^* 1,997 8 203 10 254 25 635 44 1 /i 1,130 693/8 1,762 11</4 286 4 102 8,000 3,629 20 T-436 5-10,000 1,524-3,048 200 181,437 4 36 914 iVsor 1 69 1 /z 1,765 6'/2 165 8</2 216 22 559 383/4 984 6114 1,562 1Q</1> 267 4 102 5,000 2,268 12T-430 4-8,000 1,219-2,438 125 113,398 4 or 3 30 762 1 1 /8, 1 Of 7 /8 58 1 /4 1,480 5 5 /8 143 7 178 ant 511 33 838 513/4 1,314 854 210 ZH 70 3,000 1,361 HOOK-BLOCK COMBINATION SPECIFICATIONS MODEL Rated Capability H 1 J Weight tons Kg. in. mm. in. mm. in. mm. Lb. Kg. TBJ-40 350 317,515 164 4,166 31% 806 52te 1,333 TBJ-30 250 226,796 i33te 3,391 25 635 44fe 1,130 10,500 4,763 TBJ-20 150 136,078 11714 2,978 22 559 38 3 /4 984 7,700 3,493 TBJ-12 100 90,718 95'/4 2,419 20'/t 514 33 838 5,000 2,268 TWW-40 350 317,515 141% 3,600 313/4 806 52 1 * 1,333 19,000 8,618 TWW-30 250 226,796 119 3,023 25 635 44 15 1,130 10,500 4,763 TWW-20 150 136.078 103 2,616 20 508 X 3 A 984 7,700 3,493 TWW-12 100 90,718 92 1 /2 2,350 20 ( /4 514 33 838 5,000 2,268 • GARDNER-DENVER PETROLEUM EQUIPMENT- 23 Specifications subject to change without notice.
