+ All Categories
Home > Documents > Garmin 400W : 500W Non-GarminDisplaysPilotsGuideAddendum

Garmin 400W : 500W Non-GarminDisplaysPilotsGuideAddendum

Date post: 02-Apr-2018
Category:
Upload: andre-peli
View: 228 times
Download: 0 times
Share this document with a friend

of 24

Transcript
  • 7/27/2019 Garmin 400W : 500W Non-GarminDisplaysPilotsGuideAddendum

    1/24

    400W / 500W SeriesDisplay Interfaces

    Pilots Guide Addendum

    L-3 STORMSCOPE WX-500 Weather Mapping

    Sensor L-3 SKYWATCH Trafc Advisory System

    (Model SKY497)

    L-3 SKYWATCH HP Trafc Advisory System(Model SKY899)

    Bendix/King KTA870 TAS/KMH880

    Multi-Hazard Awareness System Ryan TCAD 9900B and 9900BX

  • 7/27/2019 Garmin 400W : 500W Non-GarminDisplaysPilotsGuideAddendum

    2/24

    This Pilots Guide Addendum is written for:

    GarminGPS400W,GNC420W/420AW,andGNS430W/430AWMainSystemSoftwareVersions2.00,3.00,and later

    GarminGPS500W&GNS530W/530AWMainSystemSoftwareVersions2.00,3.00,andlaterSomedifferencesinoperationmaybeobservedwhencomparingtheinformationinthismanualtoearlierorlatersoft-

    wareversions.

    2009GarminLtd.oritssubsidiaries.AllRightsReserved.

    GarminInternational,Inc.,1200East151stStreet,Olathe,KS66062,U.S.A.

    Tel.913/397.8200or800/800.1020 Fax913/397.8282GarminAT,Inc.,2345TurnerRd.,S.E.,Salem,Oregon97302,U.S.A.Tel:503/581.8101 Fax:503/364.2138

    Garmin(Europe)Ltd.,LibertyHouse,BullsCopseRoad,HounsdownBusinessPark,Southhampton,SO409RB,U.K.Tel.+44(0)8708501243 Fax+44(0)2380524004

    GarminCorporation,No.68,Jangshu2ndRoad,Shijr,TaipeiCounty,TaiwanTel.886/2.2642.9199 Fax886/2.2642.9099

    Exceptasexpresslyprovidedherein,nopartofthisaddendummaybereproduced,copied,transmitted,disseminated,downloadedorstoredinanystoragemedium,foranypurposewithouttheexpresspriorwrittenconsentofGarmin.Garminherebygrantspermissiontodownloadasinglecopyofthismanualandofanyrevisiontothismanualontoaharddriveorotherelectronicstoragemediumtobeviewedandtoprintonecopyofthismanualorofanyrevisionhereto,providedthatsuchelectronicorprintedcopyofthismanualorrevisionmustcontainthecompletetextofthiscopyrightnoticeandprovidedfurtherthatanyunauthorizedcommercialdistributionofthismanualoranyrevisionheretoisstrictlyprohibited.

    Informationinthisdocumentissubjecttochangewithoutnotice.Garminreservestherighttochangeorimproveits

    productsandtomakechangesinthecontentwithoutobligationtonotifyanypersonororganizationofsuchchangesorimprovements.

    January2009 PartNumber190-00356-31Rev.D PrintedinU.S.A.

    Garmin is a registered trademark o Garmin Ltd. or its subsidiaries and may notbe used without the express permission o Garmin Ltd. or its subsidiaries. STORM-SCOPE and SKYWATCH are registered trademarks o L-3 Avionics Systems, Inc.

    Bendix/King is a registered trademark o Honeywell International, Inc.

  • 7/27/2019 Garmin 400W : 500W Non-GarminDisplaysPilotsGuideAddendum

    3/24

    1190-00356-31 Rev. D

    CAUTION:The Global Positioning System is operated by the United States government, which is solely responsible or itsaccuracy and maintenance. The system is subject to changes that could aect the accuracy and perormance o all GPS equip-ment. Although the Garmin 400W/500W Series units are precision electronic NAVigation AIDs (NAVAIDs), any NAVAID can bemisused or misinterpreted and thereore become unsae.

    CAUTION:Use the 400W/500W Series units at your own risk. To reduce the risk o unsae operation, careully review andunderstand all aspects o the Owners Manual and the Flight Manual Supplement, and thoroughly practice basic operationprior to actual use. When in actual use, careully compare indications rom the unit with all available navigation sources,including the inormation rom other NAVAIDs, visual sightings, charts, etc. For saety, always resolve any discrepancies beorecontinuing navigation.

    CAUTION:Use the Garmin 400W/500W Series units and the Trac/Weather Interace at your own risk. To reduce the risk o

    unsae operation, thoroughly practice basic operation prior to actual use. When in actual use, careully compare indicationsrom the Garmin 400W/500W Series Unit with all available navigation sources, including the inormation rom other NAVAIDs,visual sightings, charts, etc. For saety, always resolve any discrepancies beore continuing navigation. The altitude calculatedby the Garmin 400W/500W Series Unit is the geometric height above mean sea level and could vary signicantly rom thealtitude displayed by pressure altimeters in the aircrat.

    CAUTION:The Jeppesen database incorporated in the Garmin 400W/500W Series units must be updated regularly in order toensure that its inormation is current. Updates are released every 28 days. A database inormation packet is included in yourGarmin 400W/500W Series unit package. Pilots using an out-o-date database do so entirely at their own risk.

    CAUTION:The Trac and Weather inormation contained in this Pilots Guide Addendum is not intended to replace the docu-mentation that is supplied with the applicable Garmin 400W/500W Series unit. The user o the Trac and Weather Interaceshould know how to operate the 400W/500W series unit and be knowledgeable about the inormation in the 400W/500WPilots Guides.

    NOTE:This Pilots Guide Addendum is not intended to replace the documentation that is supplied with the Garmin400W/500W Series unit and the applicable weather/traic system.

    Foreward

    Warnings and Cautions

  • 7/27/2019 Garmin 400W : 500W Non-GarminDisplaysPilotsGuideAddendum

    4/24

    2

    Table o Contents

    SECTION 1: INTRODUCTION .................. ................... ......3SECTION 2: L-3 STORMSCOPE INTERFACE .................. ..4

    L-3 STORMSCOPE Description ........................................ 4Power-Up Sel-Test ........................................................ 4User-Initiated Test .......................................................... 4Displaying Storm Data on the Map Page ......................... 5Clearing the Map Page ................................................... 7Lightning Page400W Series ........................................ 8Lightning Page500W Series ........................................ 8Lightning Display............................................................ 9

    Lightning Display Interpretation ...................................... 9SECTION 3: SKYWATCH INTERFACE .................. ........... 10

    Introduction ................................................................. 10SKYWATCH Description ................................................ 10Power-up Sel-Test........................................................ 10User-initiated Test......................................................... 11Voice Announcements .................................................. 11Switching Between Standby and Operating Modes ........ 11Altitude Display Mode .................................................. 12Trafc Page .................................................................. 12Trafc Warning Window ................................................ 12Trafc Page Display Range ............................................ 13Confguring Trafc Data on the Map Page ..................... 13Highlighting Trafc Data Using Map Panning................. 14Monitoring Trafc ......................................................... 14Failure Response .......................................................... 15Description o Trafc Advisory Criteria ........................... 15

    SECTION 4: RYAN TCAD INTERFACE ................... .........16Ryan TCAD Description ................................................. 16Operator Controls and Basic Displays ............................ 16Confguring TCAD Data on the Map Page ..................... 17Monitoring Trafc ......................................................... 18Highlighting Trafc Data Using Map Panning................. 18TCAD Setup Page ......................................................... 18Trafc Page Fields ......................................................... 19

    Air Shield ..................................................................... 20Trafc Warning Window ................................................ 20Threat Acquisition ........................................................ 20Audible and Visible Alerts ............................................. 20Fault Displays ............................................................... 20Limitations ................................................................... 20

    Forward

    Table of Contents

    L-3 STORMSCOPE

    WX-500 Weather Mapping Sensor

    L-3 SKYWATCHTrafc Advisory System (Model SKY497)HP Trafc Advisory System (Model SKY899)

    Bendix/KingKTA870 TAS/KMH880 Multi-Hazard Awareness System

    RYAN TCADModel 9900BModel 9900BX)

    190-00356-31 Rev. D

  • 7/27/2019 Garmin 400W : 500W Non-GarminDisplaysPilotsGuideAddendum

    5/24

    3

    SECTION 1: INTRODUCTION

    TheGarmin400W/500WSeriesunitsprovidethedisplayinterfaceandcontrolforthefollowingtrafcandweatherdevices/systems:

    L-3STORMSCOPEWX-500WeatherMappingSensor

    L-3SKYWATCHTrafcAdvisorySystem(ModelSKY497)

    L-3SKYWATCHHPTrafcAdvisorySystem(ModelSKY899)

    Bendix/KingKTA870TAS/KMH880Multi-HazardAwarenessSystem

    RyanTCAD9900Band9900BX

    Theinterfacecapabilityallowstrafcandweatherdatatobeshownonthe400W/500Wseriescolordisplay,whichgivesyoutheabilitytoquicklyidentifytrafcandweatherhazardsrelativetoyouraircraft.

    190-00356-31 Rev. D

    Section 1

    Introduction

  • 7/27/2019 Garmin 400W : 500W Non-GarminDisplaysPilotsGuideAddendum

    6/24

    4

    SECTION 2: L-3 STORMSCOPE INTERFACE

    L-3 STORMSCOPE Description

    NOTE: Reer to the WX-500 Pilots Guide or a detaileddescription o the WX-500 STORMSCOPE.

    TheL-3STORMSCOPEWX-500WeatherMap-pingSensorisapassiveweatheravoidancesystemthatdetectselectricaldischargesassociatedwiththunderstormswithina200-NMradiusoftheaircraft.

    TheSTORMSCOPEmeasuresrelativebearinganddistanceofthunderstorm-relatedelectricalactivityandreportstheinformationtothedisplay.Interaces arecurrently only available or the WX-500 STORM-SCOPE System.

    The 400W/500W Series units perorm a sel-test during power-up to ensure proper opera-tion o the applicable interace components.

    Power-Up Sel-Test

    Thepower-upself-testensuresthattheWX-500functionsareoperatingproperly.AnerrormessageisdisplayedontheMessagePageifdataisnolonger

    beingreceived.

    User-Initiated Test

    Inadditiontothepower-uptest,theWX-500per-formsacontinuousself-test.Thiscontinuousself-test

    isperformedseveraltimesperminute.Auser-initiatedtestcanalsobeperformed.TheWX-500PilotsGuidelistsallofthepossiblefaults,probablecauses,andrecommendedactionsifsystemfailuresarenoted.

    In addition to the power-up test, the user can

    perorm a sel-test that is executed throughthe 400W/500W Series unit display.

    To perorm a user-initiated test:

    1. From the deault Nav Page, turn the smallright knob to select the Lightning (LTNG)

    Page.2. Press MENU to display the Page Menu.

    3. Turn the small right knob to select Sel-Test? and press ENT.

    190-00356-31 Rev. D

    Section 2

    L-3 Stormscope Interface

  • 7/27/2019 Garmin 400W : 500W Non-GarminDisplaysPilotsGuideAddendum

    7/24

    5

    Displaying Storm Data on the Map Page

    TheMapPagedisplayscellorstrikeinformationusingyellowlightningstrikesymbologyoverlaid

    onamovingmap.Thisaddedcapabilityimprovessituationalawareness,whichinturnmakesitmucheasierforthepilottorelatestormactivitytoairports,NAVAIDs,obstaclesandothergroundreferences.

    NOTE:Storm data is displayed on the Map Page only iaircrat heading is available.

    Innormaloperation,thecurrentmodeandratearedisplayedinthetoprightcorneroftheMapPageandthebottomrightcorneroftheLightningPage.ThemodeisdescribedbythewordSTRIKEwheninstrikemode,orCELLwhenincellmode.

    NOTE:Cell mode uses a clustering program to iden-tiy clusters o electrical activity that indicate cells.

    Cell mode is most useul during periods o heavystorm activity. Displaying cell data during these peri-ods rees the user rom siting through a screen ullo discharge points and helps to better determinewhere the storm cells are located.

    190-00356-31 Rev. D

    Storm Activity

    Storm Data Displayed on the Map Page

    Strike Rate

    Cell Mode

    Section 2

    L-3 Stormscope Interface

    i

  • 7/27/2019 Garmin 400W : 500W Non-GarminDisplaysPilotsGuideAddendum

    8/24

    6 190-00356-31 Rev. D

    The strike data display phases are:

    1. Lightning Symbol (latest strikes; less than oneminute; a black guard band is placed around

    the strike symbol during the rst six secondso display).

    2. Large Plus + sign (more than one minuteold).

    3. Small Plus + sign (more than two minutesold).

    4. Strike Data is no longer displayed (ater threeminutes).

    To confgure storm data on the Map Page:

    1. From the deault Nav Page, turn the smallright knob to select the Map Page.

    2. Press MENU to display the Page Menu.

    3. Turn the small right knob to select SetupMap? and press ENT.

    4. The fashing cursor highlights the GROUP eld.Turn the small right knob to display the MapSetup Options Menu. Turn the small rightknob to select Weather and press ENT.

    5. The fashing cursor highlights Weather inthe GROUP eld. Turn the large right knob toselect the desired lighting mode eld. Turn thesmall right knob to select the desired modeand press ENT. Repeat or the remaining eldsand options.

    6. Return to the Map Page by pressing CLR.

    NOTE:Only the data that is viewable on the screen isincluded in the strike rate. Thereore, you can zoom inand see what the strike rate is locally, or you can zoomout or a bigger picture.

    Also, when panning with the cursor on the Map Page,you can zoom in and isolate individual cells. Pleasenote, however, that strike data is not typically updatedon the Map Page while the panning cursor is on.

    Thereore, when the panned map is rst displayed, thedata is only a snapshot o conditions (as mentionedabove, the strike rate will refect viewable data only).

    Section 2

    L-3 Stormscope Interface

    S ti 2

  • 7/27/2019 Garmin 400W : 500W Non-GarminDisplaysPilotsGuideAddendum

    9/24

    77190-00356-31 Rev. D

    Clearing the Map Page

    RoutinelyclearingtheMapPageofalldischargepointsisagoodwaytodetermineifastormisbuild-

    ingordissipating.Inabuildingstormdischargepointsreappearfasterandinlargernumbers.Inadissipatingstormdischargepointsappearslowerandinsmallernumbers.

    Clearing discharge points rom the Map Page.

    To clear the Map Page o all dischargepoints:

    1. From the deault Nav Page, turn the smallright knob to select the Map Page.

    2. Press MENU to display the Page Menu. Turnthe small right knob to select Clear Storm

    Data? and press ENT.Changing the Storm Data Display Range

    Stormdatacanbedisplayedonthe2000NMzoomscale,butthedataonlygoesoutasfarastheSTORMSCOPEcanreport(200NM).The500NMzoomscalewilldisplayalllightningdata.Scales

    greaterthan500NMdonotdisplayanyadditionalSTORMSCOPEdata.

    Changing the storm data display range onthe Map Page.

    To select a storm data display range:

    1. From the deault Nav Page, turn the smallright knob to select the Map Page. PressMENU to display the Page Menu.

    2. Turn the small right knob to select SetupMap? and press ENT. Turn the small rightknob to select the Weather Group and press

    ENT. Turn the large right knob to select thedesired lightning symbol option. Turn the smallright knob to select the desired range andpress ENT.

    Section 2

    L-3 Stormscope Interface

    Section 2

  • 7/27/2019 Garmin 400W : 500W Non-GarminDisplaysPilotsGuideAddendum

    10/24

    88

    Lightning Page400W Series

    InadditiontotheMapPage,stormdatacanalsobeviewedontheLightningPage.Inthe400WSeries,WhentheSTORMSCOPEisconnectedtotheunit,theLightningPageappearsaftertheTrafcPageinthesequenceof

    NavPages.

    Deault NAV

    Map NAVCOM Position SatelliteStatus

    VNAV

    Trafc

    Lightning

    TerrainXM Wx

    Lightning Page500W Series

    InadditiontotheMapPage,stormdatacanalsobeviewedontheLightningPage.Inthe500WSeries,whentheSTORMSCOPEisconnectedtotheunit,theLightningPageappearsaftertheTrafcPageinthesequenceofNavPages.

    Map Trafc NAVCOM SatelliteStatus

    Lightning

    TerrainDeault Nav XM Wx

    190-00356-31 Rev. D

    Section 2

    L-3 Stormscope Interface

    Section 2

  • 7/27/2019 Garmin 400W : 500W Non-GarminDisplaysPilotsGuideAddendum

    11/24

    99190-00356-31 Rev. D

    Lightning Display

    TheLightningPagedisplayseithera360ora120viewingangle.Innormaloperation,thecurrentstrike

    rateisdisplayedinthetoprightcorner,accompaniedinthetopleftcornerbythewordLTNG.Wheninstrikemode,StrikeisdisplayedinthelowerrighthandcorneroftheWeatherPageandwhentheunitisincellmode,CellisdisplayedinthelowerrighthandcorneroftheLightningPage.

    To select the desired Lightning Display

    Mode:1. From the deault NAV Page, turn the small

    right knob to select the Lightning Page.

    2. Press MENU to display an options menu.

    3. Select the desired display angle rom theoptions menu and press ENT.

    Strike Rate

    Storm Activity

    Lightning Display

    OrientationMethod

    Weather Mode

    Stormscope Operation

    Lightning Display Interpretation

    Forlightningdisplayinterpretation,studytheexamplesintheWX-500Pilot'sGuidethataredesignedtohelpyourelatethecellorstrikepatternsshownonthedisplaytothesizeandlocationofthun-derstormsthatmaybenearyouraircraft.

    Section 2

    L-3 Stormscope Interface

  • 7/27/2019 Garmin 400W : 500W Non-GarminDisplaysPilotsGuideAddendum

    12/24

    Section 3

  • 7/27/2019 Garmin 400W : 500W Non-GarminDisplaysPilotsGuideAddendum

    13/24

    1111190-00356-31 Rev. D

    To begin tracking intruder aircrat

    1. Turn the cursor on and highlight STBY.

    2. Turn the small right knob to select OPER.

    3. Press ENT to conrm operating mode andbegin tracking intruder aircrat.

    Operating Mode is confrmed by the displayo OPER in the upper right-hand corner o

    the Trafc Page.

    NOTE:The FAILED message occurs when the systemdetects an error and prohibits urther trac displayoperation as long as this message stays on the screen.

    User-initiated Test

    NOTE:A user-initiated test can only be perormedwhen in standby or ailed mode.

    Inadditiontothepower-uptest,theSKYWATCHperformsacontinuousself-test.Thiscontinuousself-

    testisperformedseveraltimesperminute.Auser-initiatedtestoftheSKYWATCHinterfacecanalsobeperformed.

    To perorm a user-initiated test:

    1. Turn the small right knob to select the TracPage.

    2. From the Trac Page, press MENU to display

    the Page Menu.

    3. Turn the small right knob to select SelTest? and press ENT.

    Voice Announcements

    SeetheSKYWATCHPilotsGuideforinformationonvoiceannouncements.

    Switching Between Standby and Operating Modes

    Theunitmustbeinoperatingmodefortrafctobedisplayed.Theabilitytoswitchoutofstandbyintooperatingmodeonthegroundisespeciallyusefulforscanningtheairspacearoundtheairportbeforetakeoff.

    To switch into Operating Mode romStandby Mode:

    1. Pre ss the cursor knob and highlightSTBY. Turn the small right knob to selectOPER?.

    2. Press ENT to conrm and place the SKYWATCHin operating mode.

    NOTE:The SKYWATCH switches out o standby into the6-NM display range. I your aircrat has a squat switchand you do not manually switch out o standby, theSKYWATCH will automatically switch out o standby 8to 10 seconds ater takeo.

    To switch into Standby Mode rom the Tra-fc Page:

    1. Turn the cursor on and highlight OPER.

    2. Turn the small right knob to selectSTBY?.

    3. Press ENT to conrm and place the SKYWATCHin standby mode.

    NOTE:I your aircrat has a squat switch, STBYisnot displayed while you are airborne but will go into

    standby 24 seconds ater landing. This delay allows theSKYWATCH to remain in the operating mode during atouch-and-go maneuver.

    Section 3

    Skywatch Interface

    Section 3

  • 7/27/2019 Garmin 400W : 500W Non-GarminDisplaysPilotsGuideAddendum

    14/24

    1212 190-00356-31 Rev. D

    Altitude Display Mode

    The name o the selected altitude display

    mode (ABV: look up, NRM: normal, BLW: lookdown, or UNR: unrestricted) is displayed

    in the upper let-hand corner o the TrafcScreen. The SKY 497 continues to track upto 30 intruder aircrat within its maximum

    surveillance range, regardless o the altitudedisplay mode selected.

    To change the Altitude Display Mode:1. From the Trac Page, turn the cursor on,

    highlight the current mode and turn the smallright knob to cycle through the options.

    2. With each turn o the knob, the screen changesto display the trac detected within the selectedaltitude display range. The 400W/500W Series

    screen also displays unrestricted trac (UNR)having a range o maximum specied by theSKYWATCH Pilots Guide. Please reer to theSKYWATCH Pilots Guide or inormationregarding altitude display ranges.

    3. Note that conrmation is not required. Themode is changed immediately when using the

    small right knob. Turn the cursor o whenselection is made.

    Trafc Page

    TrafccanbedisplayedbothontheMapPage(onlyifheadingisavailable)andontheTrafcPage.

    Altitude Display Mode

    Display Range

    Trafc Advisory(with no bearing inormation)

    Operating Mode

    Trafc

    Trafc Page

    Trafc Warning Window

    Whentheunitisnotonthetrafcpageandatraf-cthreatisimminent,theTrafcWarningWindowisdisplayed.TheWarningWindowshowsasmallmapandcandisplaytheTrafcPage(iftheuserpresses

    ENT)orreturntothepreviouspage(iftheuserpressesCLR).

    Trafc Warning Window

    NOTE:The Trac Warning Window is disabled whenthe aircrat ground speed is less than 30 knots or whenan approach is active.

    Skywatch Interface

    Section 3

  • 7/27/2019 Garmin 400W : 500W Non-GarminDisplaysPilotsGuideAddendum

    15/24

    1313190-00356-31 Rev. D

    NOTE:SKYWATCH data is only displayed on the MapPage if suitable aircraft heading data is available. See theGarmin 400W or 500W Series Installation Manuals avail-able at your authorized Garmin service center for details.

    Trafc Page Display Range

    YoucanchangethedisplayrangeontheTrafcPageatanytime.

    1. Press the RNG Key to cycle through the ol-lowing range options:

    SKYWATCH(SKY497)2NM,2and6NM,and

    6and12NM. SKYWATCHHP(SKY899)2NM,2and6NM,6and12NM,and12and24NM.

    Bendix/KingKTA870/KMH8802NM,2and6NM,6and12NM,12and24NM,and20and40NM.

    Confguring Trafc Data on the Map Page

    ThedisplayoftrafcinformationisdesignedtocloselyresemblethedisplaysymbologyusedbyL-3ontheSKYWATCH.Trafc is only displayed onthe Map Page i aircrat heading data is available.When heading is not available, Trafc Advisoriesare displayed as non-bearing banners on the MapPage.

    Selections or confguring trafc data aremade rom the Map Setup Menu on the Map

    Page.

    To confgure trafc on the Map Page:

    1. Turn the small right knob to select the MapPage.

    2. Press MENU to display the Page Menu. Turnthe small right knob to select Setup Map?and press ENT.

    3. The fashing cursor highlights the GROUP eld.Turn the small right knob to select Trac andpress ENT.

    4. Turn the large right knob to select the desiredTrac Mode option. Turn the small right knobto select the desired option and press ENT.Repeat the step or Trac Symbol and TracLabel.

    5. Return to the Map Page by pressing CLR.

    Trafcmodeallowstheoperatortochoosewhich

    trafcisdisplayed(alltrafc,trafcandproximityadvi -sories,ortrafcadvisoriesonly).Thetrafcsymbolisthe

    symbolusedtodepictthetypeoftrafc(400W/500W

    SeriesandL-3usethesamesymbology):

    TrafcAdvisories(TA)Yellow

    ProximityAdvisories(PA)White

    (maybeconguredasCyan)

    OtherWhite(maybeconguredasCyan)

    NOTE: Proximity Advisories (PA) are displayed assolid white diamonds (may be congured as cyan).SKYWATCH shows these PAs as other (hollow dia-

    monds). PAs are dened as trac within the 4.0-NMrange, with 1200 eet o altitude separation, and nota trac advisory (TA).

    Thetrafclabelisthealtitudeseparationaboveorbelowthesymbolandtheverticalspeedsensearrow

    Skywatch Interface

    Section 3

  • 7/27/2019 Garmin 400W : 500W Non-GarminDisplaysPilotsGuideAddendum

    16/24

    1414 190-00356-31 Rev. D

    totherightofthesymbol.FromtheMapPage,youcandisplaytrafcinathumbnailformatinanyofthetopthreedataelds(topfoureldsonthe500W

    Series)ontherightsideoftheMapPage.

    When a Trafc Advisory is active, the Trafc banner is dis-played in the lower right corner o the Map Page.

    To display Thumbnail Trafc on the Map Page

    1. Turn the small right knob to select the MapPage.

    2. Press MENU to display the Page Menu.

    3. Turn the small right knob to select ChangeFields? and press ENT.

    4. Select one o the top three elds (top ourelds on the 500W Series). Select TRFC romthe Select Field Type List and press ENT. Notethat the thumbnail range deaults to 6 NM andcannot be changed.

    Highlighting Trafc Data Using Map Panning

    Anothermappagefunctionispanning,whichallowsyoutomovethemapbeyonditscurrentlimitswithoutadjustingthemapscale.Whenyouselectthepanningfunctionbypressingthesmall rightknobatargetpointerflashesonthemapdisplay.A

    windowalsoappearsatthetopofthemapdisplayshowingthelatitude/longitudepositionofthepointer,plusthebearinganddistancetothepointerfromyourpresentposition.

    When the target pointer is placed on trafc,the trafc range and altitude separation are

    displayed.

    To select the panning unction and pan themap display:

    1. Press the small right knob to activate thepanning target pointer.

    2. Turn the small right knob clockwise to

    move up, or turn it counterclockwise to movedown.

    3. Turn the large right knob clockwise to moveright, or turn it counterclockwise to move left.

    4. To cancel the panning unction and return toyour present position, press the small rightknob.

    Whenthetargetpointerisplacedontrafc,thetrafcrangeandaltitudeseparationaredisplayed.Thetrafcisidentiedas:

    TA:TrafcAdvisory,PA:ProximityAdvisory,

    TRFC:OtherTrafc

    Monitoring Trafc

    SeetheinformationintheSKYWATCHPilotsGuideregardingmonitoringtrafconthedisplayandthecorrespondingactionstotake.

    Skywatch Interface

    Section 3

  • 7/27/2019 Garmin 400W : 500W Non-GarminDisplaysPilotsGuideAddendum

    17/24

    15190-00356-31 Rev. D

    Failure Response

    ErrorsindicatedbyaFAILEDmessageonthescreenpreventcontinueduseoftheSKYWATCH.

    PleaseseetheL-3SKYWATCHPilotsGuidefordetailedinformationonFailureResponse.

    Description o Trafc Advisory Criteria

    ForadescriptionofTrafcAdvisorycriteriaanddisplayinterpretation,pleaseseetheSKYWATCHPilotsGuide.

    The SKYWATCH Pilots Guide containsdetailed inormation on trafc advisory and

    display interpretation.

    Skywatch Interface

    Section 4

  • 7/27/2019 Garmin 400W : 500W Non-GarminDisplaysPilotsGuideAddendum

    18/24

    16

    SECTION 4: RYAN TCAD INTERFACE

    Allinformationinthissectionpertainingtothedis-

    playandcontroloftheRyan9900BTCADalsoappliestotheRyan9900BXTCADexceptforthefollowing:

    TCAS-like symbols are used inthe9900BX.TCADsymbolsareusedwiththe9900B(seethetableonpage17).

    Altitudemodesareavailable (normal,lookup,

    lookdown,unrestricted).

    Rangesaremanuallycontrolledinsteadofbeing

    automaticallyre-sizedtothecurrentshield.

    Trafcdisplayrangeselectionsaredifferent:

    -Ryan9900Brangeisslavedtocurrentshield

    size. -Ryan9900BX1NM,1and2NM,2and6NM,6and12NM,and12and24NM.

    See the Ryan TCAD Pilots Handbook or adescription o the trafc symbols.

    Ryan TCAD Description

    NOTE: Reer to the Ryan TCAD Pilots Guide or adetailed description o the Ryan TCAD System.

    TheRyanTCAD(TrafcandCollisionAlertDevice)isanon-boardairtrafcdisplayusedtoidentifypotentialcollisionthreats.TCADcomputesrelativealtitudeandrangeofthreatsfromnearbyModeCandModeS-equippedaircraft.TCADwillnotdetectaircraftwithoutoperatingtranspondersorthosethatarebeyondradarcoverage.TCAD,withindenedlimits,createsashieldofairspacearoundtheaircraftthatdetectedtrafccannotpenetratewithouttrigger-inganalert.

    Operator Controls and Basic Displays

    Ifthereisnocommunicationbetweenthe400W/500WSeriesunitdisplayandtheTCADunit,a

    messagewillappear,notifyingtheuser.Afterinitial-

    ization,proceedwithoperationofthe400W/500WSeriesunitinanormalmanner.TCADdatacanbeshowninathumbnailviewontheMapPage.

    The Map Page can display TCAD trafc in anyo the top three felds (or top our felds on a500W Series unit) located on the right-hand

    side o the display.

    TCADdataalsodisplaysontheTrafcPageandMapPages,ifheadingdataisavailable.ThesymbolsforclosingandopeningtrafcshownonboththeMapPageandtheTrafcPageareidenticaltothoseshownontheRyanTCAD:

    190-00356-31 Rev. D

    Ryan TCAD Interface

    Section 4

    f

  • 7/27/2019 Garmin 400W : 500W Non-GarminDisplaysPilotsGuideAddendum

    19/24

    17

    9900B (TCAD) Symbols

    TRFC (White)Altitude separa-tion >500 eet, steady altitude

    separation(color may be confgured as cyan)

    TA (Yellow)Altitude separa-tion500 eet, steady altitudeseparation

    TRFC (White)Altitude separa-tion >500 eet, closing

    (color may be confgured as cyan)

    PA (White)Altitude separa-tion500 eet, opening(color may be confgured as cyan)

    TRFC (White)Altitude separa-tion >500 eet, opening(color may be confgured as cyan)

    TA (Yellow)Altitude separa-tion500 eet, closing

    9900BX (TCAS) Symbols

    Trafc Advisory

    Proximity Advisory(color may be confgured as cyan)

    Other Trafc(color may be confgured as cyan)

    Out-o-Range Trafc Advisory

    Confguring TCAD Data on the Map Page

    ThedisplayoftrafcinformationcloselyresemblesthedisplaysymbologyusedbytheRyanTCAD.Tra-

    fc data is only displayed on the Map Page i head-ing data is available.

    You can confgure TCAD data on the Map Page using the MapSetup Menu.

    To confgure Trafc on the Map Page:

    1. Turn the small right knob to select the MapPage.

    2. Press MENU to display the Page Menu.

    3. Use the small right knob to select SetupMap? and press ENT.

    4. The fashing cursor highlights the GROUP eld.Turn the small right knob to display the MapSetup Options Menu. Turn the small rightknob to select Trac and press ENT.

    5. Turn the large right knob to select the desiredTrac Mode option. Turn the small right knobto select the desired option and press. Repeatthe step or Trac Symbol and Trac Label.

    6. Return to the Map Page by pressing CLR.TheMapPagehastheabilitytodisplaytrafcin

    athumbnailformatinanyofthetopthreeelds(topfoureldsona500WSeriesunit)ontheright-handsideoftheMapPage.

    190-00356-31 Rev. D

    Ryan TCAD Interface

    Section 4

    R TCAD I t f

  • 7/27/2019 Garmin 400W : 500W Non-GarminDisplaysPilotsGuideAddendum

    20/24

    18

    To display Thumbnail Trafc on the MapPage:

    1. Turn the small right knob to select the Map

    Page.2. Press MENU to display the Page Menu.

    3. Use the small right knob to select ChangeFields? and press ENT.

    4. Select one o the top three elds (top ourelds on a 500W Series unit). Select TRFCrom the Select Field Type List and press ENT.

    Note that the thumbnail range deaults to 6NM and cannot be changed or TCAD 9900BXand slaves to the current shield size or TCAD9900B.

    Monitoring Trafc

    RefertotheinformationintheTCADPilotsGuideregardingmonitoringtrafconthedisplayandthe

    correspondingactionstotake.

    Highlighting Trafc Data Using Map Panning

    Panningisanothermappagefunction,whichallowsyoutomovethemapbeyonditscurrentlimitswithoutadjustingthemapscale.Whenyouselectthepanningfunctionbypressingthesmallright

    knobatargetpointerashesonthemapdisplay.Awindowalsoappearsatthetopofthemapdisplayshowingthelatitude/longitudepositionofthepointer,plusthebearinganddistancetothepointerfromyourpresentposition.

    When the target pointer is placed on trafc,the trafc range, squawk code (i available),and tail number (i available) are displayed.

    To use the map panning eature:1. Press the small right knob to activate thepanning target pointer.

    2. Turn the small right knob to move up (turnclockwise), or down (turn counterclockwise).

    3. Turn the large right knob to move right (turnclockwise), or let (turn counterclockwise).

    4. To cancel map panning and return to your pres-

    ent position, press the small right knob.

    Whenthetargetpointerisplacedontrafc,thetrafcrange,altitudeseparation,squawkcode(ifavail-able),andtailnumber(ifavailable)aredisplayed.Thetrafcisidentiedasfollows:

    TA:TrafcAdvisory.Thisistrafcwith500feet,or

    less,ofaltitudeseparationthatisconvergingormaintainingaltitudeseparation.

    PA:ProximityAdvisory.Thisistrafcwith500feetofaltitudeseparationthatisnotaTA.

    TRFC:Othertrafc.

    TCAD Setup Page

    TheRyanTCADSetupPageisaccessedfromtheTrafcPage.TheTCADSetupPageallowsyoutoconguretrafcdata.ThedenitionsoftheavailableoptionsarelistedintheTCADPilotsHandbook.

    190-00356-31 Rev. D

    Ryan TCAD Interface

    Section 4

    Ryan TCAD Interface

  • 7/27/2019 Garmin 400W : 500W Non-GarminDisplaysPilotsGuideAddendum

    21/24

    19190-00356-31 Rev. D

    Ryan TCAD Setup Page (9900B only)

    To change a TCAD setup option:

    1. Turn the small right knob to select the TracPage. Press MENU to display the Page Menu.Turn the small right knob to select Setup?and press ENT.

    2. The fashing cursor highlights the Mode eld.Turn the small right knob to select the modeand press ENT. The mode selection determineswhich shield denition to display and change.Turn the large right knob to select the desiredremaining options elds. Turn the small rightknob to select the desired option and pressENT.

    3. Return to the Trac Page by pressing CLR.

    Trafc Page Fields

    TherearetwoselectableeldsontheTrafcPage:theOperatingModeFieldandtheBarometricPres-sureField.TheOperatingModeFieldselectstheTCADoperatingmode.PleaserefertotheTCADPilotsHandbookforacompletedescriptionofallmodesofoperation.Forthe9900BXmodel,thiseldisreplacedwiththeSKYWATCHstylealtitudemode.

    TCAD 9900B Operating Modes:

    GND: ground mode

    TML: terminal mode

    STD: standard mode

    ENR: en route mode

    UNR: unrestricted modeThe modes APR (approach) and DEP (depar-ture), are displayed when in that mode, but

    are not manually selectable.

    To select the Operating Mode:1. From the Trac Page, press CRSR to highlightthe operating mode eld. Turn the small rightknob to select the desired operating mode andpress ENT.

    NOTE: The trac display range is automatically set to

    the shield size and cannot be changed (9900B only).

    Thesecondselectableeld,locatedintheupperright-handcornerofthedisplay,istheBarometricPressureeld,whichdisplaystheBarometricPressureininchesofmercury.TheBarometricPressureeldontheTrafcPageallowsyoutosetthebarometricpressureintheRyanTCADunit.PleaserefertotheTCADPilotsHandbookforadetaileddescriptionof

    thisfeature.

    The Barometric Pressure feld is located inthe upper right-hand corner o the Trafc

    Page.

    Ryan TCAD Interface

    Section 4

    Ryan TCAD Interface

  • 7/27/2019 Garmin 400W : 500W Non-GarminDisplaysPilotsGuideAddendum

    22/24

    20 190-00356-31 Rev. D

    To change the Barometric Pressure:

    1. From the Trac Page, press the cursor tohighlight the Operating Mode eld. Turn the

    large right knob to select the BarometricPressure Field. Use the small right knob toselect the desired value and press ENT. Note:When editing the value, use the large rightknob to select the digit to edit.

    2. Exit the eld by pressing the CRSR button.

    WhentheTCAD9900BXmodelisinterfaced

    thereisanadditionalannunciationinthelowerlefthandcorneroftheTrafcPage.ThisindicateswhentheTCADunitisinapproachmode(APR),oriftheapproachisarmed(APRARM).

    Air Shield

    PleaserefertotheTCADPilotsHandbookfora

    detaileddescriptionoftheAirShield.

    Trafc Warning Window

    WhentheTrafcpageisnotdisplayedandatrafcthreatbecomesimminent,theTrafcWarningWindowwillbedisplayed.TheWarningWindowshowsasmallmapandcandisplaytheTrafcPage(if

    theuserpressesENT)orreturntothepreviouspage(iftheuserpressesCLR).

    Ryan TCAD Trafc Warning Window

    NOTE: The Trac Warning Window is disabled whenthe aircrat ground speed is less than 30 knots or whenan approach is active.

    Threat Acquisition

    Please,seetheTCADPilotsHandbook.

    Audible and Visible Alerts

    Voiceandtonesareusedtoalertthepilot.ThealertdescriptionsusedbyTCADarelistedintheTCADPilotsHandbook.Voiceisusedonlyduringthehigh-estlevelofalerting;otherwise,toneisused.ThevoicealertingcanbeturnedonoroffeitherontheTCADSetupPageoronthecongurationpages.SeetheGarmin400W/500WSeriesInstallationManualavail-ableatyourauthorizedGarminServiceCenter(onlyforthe9900model).

    Fault Displays

    Ifthe400W/500WSeriesunitfailstodetecttheRyanTCADorifitdetectsinvaliddatafromtheTCAD,thetrafcscreenwilldisplaythemessage,NODATA.

    LimitationsPleaseseetheTCADPilotsHandbookforlimita-

    tionsoftheTCADsystem.

    Ryan TCAD Interface

  • 7/27/2019 Garmin 400W : 500W Non-GarminDisplaysPilotsGuideAddendum

    23/24

  • 7/27/2019 Garmin 400W : 500W Non-GarminDisplaysPilotsGuideAddendum

    24/24

    2009GarminLtd.oritssubsidiaries

    GarminInternational,Inc.1200East151stStreet,Olathe,Kansas66062,U.S.A.

    GarminAT,Inc.2345TurnerRd.,S.E.,Salem,Oregon97302,U.S.A.

    Garmin(Europe)Ltd.LibertyHouse,BullsCopseRoad,HounsdownBusinessPark,

    Southhampton,SO409RB,U.K.

    GarminCorporationNo.68,Jangshu2ndRoad,Shijr,TaipeiCounty,Taiwan

    www.garmin.com

    PartNumber190-00356-31Rev.D


Recommended