Commonwealth of Australia Gazette
No. TC 18/24, Wednesday, 27 June 2018 Published by the Commonwealth of Australia
TARIFF CONCESSIONS
CONTENTS
TCO Applications ....................................................................................................... 2
TCO Applications Refused ........................................................................................ 6
TCOs Made.................................................................................................................. 7
Intention to Revoke TCOs not used in over 2 years ............................................. 11
By-Laws Made .......................................................................................................... 12
The Commonwealth of Australia Tariff Concessions Gazette (the Tariff Concessions Gazette) is free of charge on
the Department of Home Affairs internet site at: https://www.homeaffairs.gov.au/busi/domestic-manufacturers-and-importers
The Tariff Concessions Administration Section is located at 5 Constitution Ave Canberra City 2601 Contact details: General Email Inquiries:………………………………[email protected] General Inquiries: (02) 6229 3567 TAPIN help desk: (02) 6275 6534 Facsimile: (02) 6223 8180
Cat. No.
ISSN 0813-8389
©Commonwealth of Australia, 2018
2 TCO Applications Commonwealth of Australia Gazette
No TC 18/24, Wednesday, 27 Jun 2018
TCO Applications
CUSTOMS ACT 1901 - NOTICE PURSUANT TO SECTION 269K(1) - APPLICATIONS MADE FOR TARIFF CONCESSION ORDERS
Applications have been lodged for Tariff Concession Orders for the goods described in the following TABLE.
Australian manufacturers who wish to contest the granting of a Tariff Concession Order for the goods described
are invited to lodge a submission in writing in an approved form. Submissions must be lodged within 50 days
of the date of publication of this Notice.
The operative date (Op.) and TC reference number follow the description of goods.
To assist local manufacturers, the use(s) to which the goods can be put follow the description of goods.
Objections to the making of TCO submission forms are available at
https://www.homeaffairs.gov.au/Forms/Documents/b444.pdf
Contact: Email [email protected]
THE TABLE
Description of Goods including the Schedule 4 Item Number
Customs Tariff Classification General Duty Rate
8424.49.00 SPRAYERS, CROP, self-propelled, ride-on, having BOTH of the
following:
(a) spraying boom length NOT less than 20 m;
(b) spray tank volume capacity greater than 4 000 L
Op. 30.05.18 - TC 1862197
Stated Use:
For spraying agricultural crops
Applicant: JOHN DEERE LIMITED
50
5%
8424.89.90 SPRINKLERS, WATER MIST, including BOTH of the following:
(a) infrared flame detectors;
(b) water mist spray nozzles
Op. 04.06.18 - TC 1863274
Stated Use:
For the detection of fires and deployment of water mist as a
fire suppressant in applications such as particle board presses,
gas turbines, industrial fryers, paint shops and engine test beds
Applicant: BORG MANUFACTURING PTY LTD
50
5%
8425.31.00 WINCHES, portable, electric, having ALL of the following:
(a) safe working load NOT greater than 300 kg;
(b) weight NOT greater than 20 kg;
(c) battery powered;
(d) remote control
Op. 05.06.18 - TC 1864381
Stated Use:
Portable rope winches for lifting people
Applicant: INOV8 ACCESS PTY LTD
50
5%
3 TCO Applications Commonwealth of Australia Gazette
No TC 18/24, Wednesday, 27 Jun 2018
Description of Goods including the Schedule 4 Item Number
Customs Tariff Classification General Duty Rate
8431.49.90 PARTS, EXCAVATOR REVOLVING SHOVEL FRAME, being centre gudgeon
assemblies, consisting of ALL of the following:
(a) centre gudgeon;
(b) screws;
(c) tie wire;
(d) locking key;
(e) shim;
(f) nuts;
(g) adjusting collar;
(h) plates;
(i) washers
Op. 29.05.18 - TC 1861025
Stated Use:
To hold excavator revolving shovel frames
Applicant: JOY GLOBAL AUSTRALIA PTY LTD
50
5%
8431.49.90 PARTS, RIM AND/OR WHEEL, being rim AND/OR wheel bases, having
BOTH of the following:
(a) width NOT less than 254 mm;
(b) diameter NOT less than 840 mm
Op. 08.06.18 - TC 18350654
Stated Use:
Wheel components for large loaders and graders
Applicant: RIMEX WHEEL PTY LTD
50
5%
8438.90.10 ROLLERS, CHOCOLATE REFINING, having BOTH of the following:
(a) length NOT less than 850 mm and NOT greater than
1 850 mm;
(b) diameter NOT less than 300 mm and NOT greater than 500 mm
Op. 07.06.18 - TC 1865171
Stated Use:
Parts of a chocolate refining machine which process mass
into refined chocolate
Applicant: MONDELEZ AUSTRALIA PTY LTD
50
5%
8467.29.00 POWERHEADS, battery operated
Op. 30.05.18 - TC 1861927
Stated Use:
Providing power to various detachable garden tools such as
brush cutters, hedge trimmers, sweepers, cultivators, blowers and
pruners
Applicant: STIHL PTY LTD
50
5%
8479.89.90 DRY CONCRETE INGREDIENTS BATCHING PLANT, programmable logic
controlled, having ALL of the following:
(a) maximum volume capacity NOT less than 100 cubic metres per
hour;
(b) hopper, with OR without hopper liners;
(c) conveyors;
(d) discharge chutes;
(e) moisture meters;
(f) vibrators;
(g) weigher AND batcher;
(h) control panel;
(i) truck loading station housing
Op. 29.05.18 - TC 1860934
Stated Use:
For the measurement and batching of dry concrete ingredients to
predetermined specifications for loading into concrete mixing
trucks
Applicant: BGC (AUSTRALIA) PTY LTD
50
5%
4 TCO Applications Commonwealth of Australia Gazette
No TC 18/24, Wednesday, 27 Jun 2018
Description of Goods including the Schedule 4 Item Number
Customs Tariff Classification General Duty Rate
8501.10.00 MOTORS, DC, including ALL of the following:
(a) length NOT greater than 120 mm;
(b) rated voltage NOT greater than 42 V;
(c) planetary gearhead diameter NOT greater than 32 mm
Op. 30.05.18 - TC 1861923
Stated Use:
Welding equipment wire feed
Applicant: MAXON MOTOR AUSTRALIA PTY LTD
50
5%
8537.10.90 SYSTEM, EXPLOSION PROTECTIVE ALERT AND FIRE SUPPRESSION
ACTIVATION, programmable logic controlled, with or without
electric current isolators, consisting of BOTH of the following:
(a) control panel;
(b) explosion pressure, spark, flame AND temperature detection
sensors
Op. 04.06.18 - TC 1863271
Stated Use:
For the activation of explosion alert communication and fire
suppression systems in industries such as wood chip production
lines for the manufacture of particle boards
Applicant: BORG MANUFACTURING PTY LTD
50
5%
8537.10.90 CONTROL PANELS, SPARK DETECTION AND SUPPRESSION
Op. 04.06.18 - TC 1863277
Stated Use:
Operation of spark detection and suppression systems for use in
industrial processes such as particle board manufacture
Applicant: BORG MANUFACTURING PTY LTD
50
5%
8537.10.90 CONTROLLERS, BUILDING SWITCH, remotely controlled OR programmed,
having ALL of the following:
(a) maximum voltage NOT less than 24 V DC;
(b) maximum power consumption NOT greater than 2 W;
(c) internet connector;
(d) connection capacity NOT greater than 6 ports
Op. 04.06.18 - TC 1863463
Stated Use:
To remotely control building switches that have electrically
connected functions such as heating, cooling, energy usage
monitoring, lighting, blinds, shutters and room occupancy signs
Applicant: SCHNEIDER ELECTRIC (AUSTRALIA) PTY LTD
50
5%
8544.49.19 DETONATOR WIRE, duplex, electronic, copper clad ferromagnetic
steel, in reels AND/OR coils, including ALL of the following:
(a) polyurethane insulation;
(b) conductor diameter NOT greater than 0.62 mm;
(c) tensile strength of NOT less than 450 newtons;
(d) electrical resistance NOT greater than 300 ohms per
kilometre;
(e) wicking resistance between conductor AND insulation NOT
less than 3 bar
Op. 25.05.18 - TC 1860018
Stated Use:
As a communication link between detonators and electronic
blasting equipment
Applicant: ORICA AUSTRALIA PTY LTD
50
5%
5 TCO Applications Commonwealth of Australia Gazette
No TC 18/24, Wednesday, 27 Jun 2018
Description of Goods including the Schedule 4 Item Number
Customs Tariff Classification General Duty Rate
8544.49.19 DETONATOR WIRE, duplex, electronic, copper clad ferromagnetic
steel, in reels AND/OR coils, including ALL of the following:
(a) conductor diameter NOT greater than 0.62 mm;
(b) polyurethane OR polypropylene insulation;
(c) tensile strength NOT less than 240 newtons;
(d) electrical resistance NOT greater than 300 ohms per
kilometre;
(e) wicking resistance between conductor AND insulation NOT
less than 8.5 bar
Op. 25.05.18 - TC 1860021
Stated Use:
As a communication link between detonators and electronic
blasting equipment
Applicant: ORICA AUSTRALIA PTY LTD
50
5%
8701.95.90 TRACTORS, SHUNTING, including BOTH of the following:
(a) tyres AND rail flanged wheels;
(b) remote control
Op. 08.06.18 - TC 1886609
Stated Use:
Shunting of railway rolling stock
Applicant: UNIQUE RAIL PTY LTD
50
5%
8705.10.00 CRANES, MOBILE, LATTICE BOOM, having ALL of the following:
(a) lifting capacity NOT greater than 750 000 kg at 7 m radius;
(b) hoist height NOT greater than 193 m;
(c) radius NOT greater than 136 m
Op. 24.05.18 - TC 1859512
Stated Use:
For mobile lifting of extremely heavy loads at extreme heights
Applicant: MAMMOET AUSTRALIA PTY LTD
50
5%
6 TCO Applications Refused Commonwealth of Australia Gazette
No TC 18/24, Wednesday, 27 Jun 2018
TCO Applications R efused
CUSTOMS ACT 1901
NOTICE PURSUANT TO SECTION 269R(1) - APPLICATIONS FOR TARIFF CONCESSION ORDERS REFUSED
Applications for Tariff Concession Orders for the goods described in the following TABLE have been refused.
THE TABLE
Description of Goods including the Schedule 4 Item Number
Customs Tariff Classification
7419.99.00 TAGS, PET, with OR without connecting rings
Op. 08.03.18 - TC 1828219
Reason for refusal:
Substitutable goods produced in Australia in the ordinary course
of business by Kevron Plastics Pty Ltd, Campbellfield, Vic
50
7616.99.00 TAGS, PET, with OR without connecting rings
Op. 08.03.18 - TC 1828221
Reason for refusal:
Substitutable goods produced in Australia in the ordinary course
of business by Kevron Plastics Pty Ltd, Campbellfield, Vic
50
7907.00.90 TAGS, PET, with OR without connecting rings
Op. 08.03.18 - TC 1828224
Reason for refusal:
Substitutable goods produced in Australia in the ordinary course
of business by Kevron Plastics Pty Ltd, Campbellfield, Vic
50
7 TCOs Made Commonwealth of Australia Gazette
No TC 18/24, Wednesday, 27 Jun 2018
TCOs M ade
CUSTOMS ACT 1901 - NOTICE PURSUANT TO SECTION 269R(1) - TARIFF CONCESSION ORDERS MADE
Tariff Concession Orders have been made for the goods described in the following TABLE.
The operative date (Op.) and TC reference No. follow the description of goods. Local manufacturers of
substitutable goods may request the revocation of TCOs at any time.
THE TABLE
Description of Goods including the Schedule 4 Item Number
Customs Tariff Classification
2918.99.00 ISOPROPYL (E,E)-(7S)-11-methoxy-3, 7, 11-trimethy-2, 4-
dodecadienoate
Op. 03.04.18 Dec. date 20.06.18 - TC 1837935
50
3923.90.00 TUBES, polypropylene, threaded, with OR without ANY of the
following:
(a) barcodes;
(b) caps;
(c) jackets whether OR not co-moulded;
(d) lid locks;
(e) racks;
(f) tube locks;
(g) twist locks
Op. 13.03.18 Dec. date 20.06.18 - TC 1829322
50
8414.51.00 EXHAUST FANS, wall OR window OR ceiling mounted, having ALL
of the following:
(a) rated voltage NOT greater than 250 VAC;
(b) air flow NOT less than 360 m3/h and NOT greater than
600 m3/h;
(c) impeller diameter NOT greater than 250 mm;
(d) power consumption NOT greater than 45 W
Op. 15.03.18 Dec. date 20.06.18 - TC 1830872
50
8415.81.00 AIR CONDITIONERS, MARINE, reverse cycle, having ALL of the
following:
(a) cooling capacity NOT less than 1.4kW;
(b) supply voltage NOT less than 200 V;
(c) sea water inlet
Op. 29.03.18 Dec. date 22.06.18 - TC 1836692
50
8418.69.00 COOLER, WAFER SANDWICH, spiral
Op. 23.03.18 Dec. date 22.06.18 - TC 1834692
50
8421.29.90 STRAINERS, OBLIQUE Y TYPE, brass, with OR without magnet
inserts, having BOTH of the following:
(a) working temperature NOT greater than 180 Degrees Celsius;
(b) working pressure not greater than 2 000 Kpa
Op. 16.03.18 Dec. date 21.06.18 - TC 1831424
50
8421.29.90 EFFLUENT FILTRATION SYSTEM, OIL AND/OR GAS WELL, whether OR not
assembled, including BOTH of the following:
(a) NOT less than one pot;
(b) interconnecting pipes,
with OR without ANY of the following:
(i) isolation AND bypass valves AND/OR bypass drain;
(ii) telescopic frame AND/OR hoist
Op. 22.03.18 Dec. date 20.06.18 - TC 1833904
50
8428.39.00 ROD CONVEYORS, including ANY of the following:
(a) drive units;
(b) gears AND/OR bearings;
(c) protection guides
Op. 26.03.18 Dec. date 22.06.18 - TC 1835366
50
8 TCOs Made Commonwealth of Australia Gazette
No TC 18/24, Wednesday, 27 Jun 2018
Description of Goods including the Schedule 4 Item Number
Customs Tariff Classification
8428.90.00 ASH HANDLING SYSTEM, RECOVERY BOILER AND/OR ECONOMISER,
including ALL of the following:
(a) ash hoppers;
(b) doors;
(c) rotary feeders;
(d) slide gate valves;
(e) drag chain conveyers;
(f) vertical chutes;
(g) expansion joints
Op. 22.03.18 Dec. date 20.06.18 - TC 1833917
50
8428.90.00 LINEAR ROBOTS, sheet layer, with OR without ANY of the following:
(a) suction arm;
(b) lifting mast;
(c) slot magazine;
(d) driving rail
Op. 27.03.18 Dec. date 20.06.18 - TC 1835372
50
8428.90.00 SORTING AND FEEDING AND POSITIONING LINE, PLASTIC CONTAINER AND
CAP, including ALL of the following:
(a) conveyor;
(b) hopper;
(c) elevator;
(d) feeder
Op. 04.04.18 Dec. date 20.06.18 - TC 1837956
50
8438.10.90 MIXERS, BATTER, having ALL of the following:
(a) batch capacity NOT less than 60 kg;
(b) holding tank NOT less than 200 L;
(c) gentle mixing turbine
Op. 23.03.18 Dec. date 21.06.18 - TC 1834688
50
8438.10.90 WAFER SHEET CONDITIONING MACHINES, with OR without an air
conditioning unit, having a wafer sheet capacity NOT less than
478 and NOT greater than 1 500
Op. 23.03.18 Dec. date 20.06.18 - TC 1834690
50
8467.29.00 GRINDERS, with OR without ANY of the following:
(a) safety guards OR safety covers;
(b) wrenches;
(c) side handles OR grips;
(d) lock nuts;
(e) inner flanges;
(f) depressed centre wheels;
(g) grinding discs OR wheels;
(h) carry cases;
(i) cutting flanges;
(j) grinding flanges;
(k) wireless interface units;
(l) collets AND nuts;
(m) collet cones;
(n) collet nuts
Op. 26.03.18 Dec. date 20.06.18 - TC 1834915
50
8467.29.00 SCREWDRIVERS, with OR without ANY one OR more of the following:
(a) side grips OR handles;
(b) nozzle modules;
(c) locator modules;
(d) bits;
(e) carry cases;
(f) belt hooks OR clips;
(g) nutsetters
Op. 28.03.18 Dec. date 21.06.18 - TC 1836263
50
8479.60.00 EVAPORATIVE AIR COOLER, TURBINE INLET, having BOTH of the
following:
(a) airflow exceeding 190 000 m3 per Hour;
(b) cooling capacity exceeding 1 100 Kw
Op. 28.03.18 Dec. date 21.06.18 - TC 1836255
50
9 TCOs Made Commonwealth of Australia Gazette
No TC 18/24, Wednesday, 27 Jun 2018
Description of Goods including the Schedule 4 Item Number
Customs Tariff Classification
8481.80.90 BALL VALVES, having ALL of the following:
(a) brass alloy body AND aperture;
(b) brass square cap;
(c) inlet AND outlet diameter NOT less than 15 mm and NOT
greater than 80 mm
Op. 16.03.18 Dec. date 20.06.18 - TC 1831420
50
8481.80.90 BALL VALVES, having ALL of the following:
(a) flanged;
(b) ductile iron body;
(c) full bore diameter NOT less than 25 mm and NOT greater
than 200 mm
Op. 19.03.18 Dec. date 20.06.18 - TC 1832202
50
8481.80.90 FLOW CONTROL VALVES, balancing, cast iron construction, having
ALL of the following:
(a) pressure rating NOT less than 1 600 KPa;
(b) valve body size NOT less than 50 mm and NOT greater
than 300 mm;
(c) pressure differential measurement test points
Op. 19.03.18 Dec. date 20.06.18 - TC 1832204
50
8504.40.90 INVERTERS, string, multiple phase, with OR without built-in AC
OR DC disconnector switch, having ALL of the following:
(a) frequency NOT greater than 60 Hz;
(b) maximum power point tracking systems NOT greater than 6;
(c) output current being ANY of the following:
(i) NOT less than 45 A and NOT greater than 50 A;
(ii) NOT less than 61 A and not greater than 77 A;
(iii) NOT less than 140 A and NOT greater than 145 A;
(d) wired AND/OR wireless communication interface
Op. 26.03.18 Dec. date 20.06.18 - TC 1835362
50
8504.40.90 CHARGE STATION, ELECTRIC MOTOR VEHICLE BATTERIES, output voltage
NOT less than 150 VDC and NOT greater than 920 VDC,
being EITHER of the following:
(a) car chargers having an operating temperature NOT less
than -35 degrees Celsius and NOT greater than 55 degrees
Celsius, including ALL of the following:
(i) module power NOT less than 110 kW and NOT greater
than 600 kW;
(ii) charge capability 400 V cars at 150 kW;
(iii) maximum DC output current per charge post NOT
exceeding 500 A;
(iv) input voltage NOT greater than 450 VAC;
(b) heavy vehicle chargers having an operating temperatures
NOT less than -35 degrees Celsius and NOT greater than 50
degrees Celsius with OR without automated 4-pole rooftop
connection INCLUDING ALL of the following:
(i) module power NOT less than 50 kW and NOT greater
than 600 kW;
(ii) output current, per 150kW module, NOT greater than
250 A;
(iii) input voltage NOT greater than 450 VAC;
Op. 29.03.18 Dec. date 22.06.18 - TC 1836821
50
8536.50.99 ISOLATOR SWITCHES, single OR multiple pole, rail mounting
support, having ALL of the following:
(a) operational voltage NOT greater than 250 VAC;
(b) current NOT greater than 80 A;
(c) conditional short-circuit current NOT greater than 10 kA
Op. 29.03.18 Dec. date 21.06.18 - TC 1837351
50
8537.10.90 CONTROL PANELS, CO-GENERATION BOILER,
having ALL of the following:
(a) programmable logic controller;
(b) safety instrument system;
(c) human machine interface
Op. 22.03.18 Dec. date 20.06.18 - TC 1833907
50
10 TCOs Made Commonwealth of Australia Gazette
No TC 18/24, Wednesday, 27 Jun 2018
Description of Goods including the Schedule 4 Item Number
Customs Tariff Classification
8701.94.90 TRACTORS, AIRCRAFT PUSHBACK AND TOWING, engine power NOT less
than 75 kW AND not greater than 130 kW
Op. 06.04.18 Dec. date 20.06.18 - TC 1839240
50
9405.40.00 LIGHTS, FLOOD, non-ceramic with OR without ceramic bulb-holder
OR metal halide lamp OR high pressure sodium lamp, having ALL of
the following:
(a) aluminium housing;
(b) aluminium reflector;
(c) mounting bracket;
(d) toughened glass visor;
(e) ethylene propylene diene monomer rubber seal;
(f) NOT less than 1 000 W
Op. 22.03.18 Dec. date 21.06.18 - TC 1833914
50
11 Intention to Revoke TCOs not used in over 2 years Commonwealth of Australia Gazette
No TC 18/24, Wednesday, 27 Jun 2018
Intention to Revoke TC Os not used i n over 2 years
TARIFF CONCESSION ORDERS (TCOs) NOT USED IN THE PREVIOUS 2 YEARS
The Comptroller-General of Customs is satisfied that the TCOs listed in the table below are no longer required
because, in the 2 years preceding the day of this notice, they have not been quoted in an import declaration
to secure a concessional rate of duty.
From Thursday, 26 July 2018, it is intended to take action to revoke these Orders under subsection 269SD(1A)
of the Customs Act 1901. In accordance with subsection 269SG(2) of the Customs Act 1901, in transit provisions
shall apply. If revoked, the expected date of effect will be 26 July 2018.
Interested parties are invited to provide, by close of business, Wednesday 25 July 2018, written reasons why
an Order should NOT be revoked.
Please advise if any of the Orders listed below have been quoted on an import declaration.
If a request is made to retain an Order used for the granting of a Determination, please specify the
Determination and the linked Item number to enable mapping to the Order and its scope.
THE TABLE
______________________________________________________________________________________________________________
Tariff
Classification Description Concession Number
______________________________________________________________________________________________________________
8427.20.00 WORKS TRUCKS, ALUMINIUM FLUORIDE TRANSPORT AND HOPPER FILLING,
mobile, having BOTH of the following:
(a) articulated discharge augers;
(b) centrally positioned rear cameras
Op. 22.10.13 Dec. date 13.01.14 - TC 1335329
8428.39.00 CASE AND/OR CARTON SEPARATION AND HANDLING SYSTEM, whether OR
not assembled, programmable logic controlled, having ALL of the
following:
(a) conveyors, having BOTH of the following:
(i) plastic belts;
(ii) wheels,
(b) optical sensor AND measurer;
(c) case AND/OR carton orientation pusher arm
Op. 21.11.13 Dec. date 03.03.14 - TC 1338999
8428.90.00 LIVE POULTRY PROCESSING SYSTEM, programmable logic controlled,
having ALL of the following:
(a) poultry stunners;
(b) hanging platforms;
(c) module washers;
(d) gas extraction emergency controls;
(e) crate handlers AND conveyors
Op. 11.10.13 Dec. date 29.01.14 - TC 1334128
8428.90.00 HANDLING SYSTEM, programmable logic controlled, including ALL of
the following:
(a) conveyors;
(b) pouch OR parcel transfer robotic arm;
(c) conveyor belts;
(d) tray stacking robotic arm;
(e) tray sorting turntables
Op. 04.11.13 Dec. date 30.01.14 - TC 1336803
8428.90.00 SURGE HOPPERS, COPPER PROCESSING SYSTEM, cylinder AND/OR cube
shaped, rubber lined
Op. 05.12.13 Dec. date 21.05.14 - TC 1340490
12 By-Laws Made Commonwealth of Australia Gazette
No TC 18/24, Wednesday, 27 Jun 2018
By-Laws M ade
CUSTOMS ACT 1901
CUSTOMS TARIFF ACT 1995
SCHEDULE 4
BY-LAW No. 1800128
I, Alison Neil, delegate of the Comptroller-General of Customs, under section 271 of the Customs Act 1901
make the by-law set out in the Schedule below.
THE SCHEDULE
BY-LAW No. 1800128
Item 56
Schedule 4
1. This by-law may be cited as Customs By-law No. 1800128.
2. This by-law commences on 1 July 2018.
3. For the purposes of subparagraph (a)(i) of item 56 of Schedule 4 to the Customs Tariff Act 1995 (the
Customs Tariff Act), the following requirements are prescribed:
i. the kits do not indicate whether their contents are medicaments or placebos; and
ii. the kits do not contain goods other than:
a. the medicaments and/or placebos, whether or not in syringes or other delivery
mechanisms;
b. any item or packaging which is necessary for the safe transport and/or storage of the
goods;
c. any associated and necessary documentation and forms.
4. For the purposes of subparagraph 3(i), identifiers, regardless of their form, that cannot be deciphered
without additional information or equipment, do not indicate whether the contents of the kit are
medicaments or placebos.
5. For the purpose of this by-law “placebo” means a good not containing an active agent under study,
administered to some participants to compare the effects of the active agent to other participants.
6. For the purpose of this by-law, the “Customs Tariff Act 1995” means the Customs Tariff Act 1995, as
amended or proposed to be altered.
Dated this 5th day of June 2018.
Alison Neil
Delegate of the
Comptroller-General of Customs