GE Lighting Sviestuvai

GE Lighting

FITTING CATALOGUE1997/98

GE Lighting

LIGHTING FIXTURES

GE Lighting

GE LIGHTING

We reserve the right to make changes to the technical characteristics of the lamps and equipment in this catalogue at any time and without notice.

Technical drawings are not to scale.Dimensions are expressed in mm.

CONTENTS

GE Lighting 1

INDUSTRIAL LIGHTING 5

Introduction to N-PACK 6Version NPW 7Version NPP 8Version NPQ 10N-PACK accessories 11NAL, NBL 15NAL, NBL accessories 18MARINER 19MAC 22MAC/R 23Special versions 24EUROBAY 27

COMMERCIAL LIGHTING 28

Introduction to MULTILITE System 8000 30MULTILITE System 8000 31Accessories 36Specifications 40Free standing Wall-mounted uplight 41Introduction to MULTILITE System 6000 42MULTILITE System 6000 43Accessories 48Specifications 51Introduction to MULTILITE System 3000 52MULTILITE System 3000 and accessories 53Specifications 55Introduction to Series 5000 58Optical accessories 59Series 5500 60Series 5501 62Series 5503 64Seriee 5504 66Series 5506 68Special versions and specifications 70NUPLEX 71STYLO 72EUROSTYLO 74FLAT 75

LIGHTING WITH 2D LAMPS 76

2D lamps 78STEP 79BRIO 80BRIO emergency 81CLUB 82CLUB emergency 83POCKET 84DIAMOND 86DIAMOND emergency 87QUAD 88Q-Bulk 89TRIS 90CITY 92ELITE 94Series 5503 2D 95

DISPLAY LIGHTING 96

TOP/2DR 98TOP/2D 99TOP/DBX 100TOP/F TOP/A 102TOP/D 103TOP/M 104Transformers 105TOP/HA 106TOP/MQF TOP/MQA 107ARCLITE 108LIVELIGHT 109CRICKET 110

FLOODLIGHTING 114

EUROFLOOD 116OTQ 1000 118OQ 2000 120CSA Watertight power supply boxes 122HALOPAK 123MASTERPAK 125EUROSTREET 127

PHOTOMETRIC DATA 129

2 page

2D BR Brio 80

2D Bulk 89

2D CL Club 83

2D CY City 93

2D CYA 93

2D CYP 91

2D CYW 93

2D DM Diamond 86

2D PK Pocket 85

2D PKC Pocket 85

2D QB Q-Bulk 89

2D Quad 88

2D ST Step 79

2D TR Tris 91

2D TR1 91

2D TR2 91

2D TRG Tris 91

3

3000 Multilite 52

3001 53

3002 53

3003 53

3004 53

3020 53

3023 53

3030 53

3100 54

3101 54

3149 54

3150 54

3151 54

3169 54

3170 54

3178 55

3180 55

5

5000 Serie 58

5500 60

5501 62

5503 64

5503 2D 95

5504 66

5506 68

6 page

6000 Multilite 42

6001 43

6005 43

6010 43

6015 43

6018 43

6020 43

6022 44

6030 44

6100 44

6101 44

6140 44

6149 48

6150 48

6151 48

6169 39

6169 48

6170 48

6171 48

6172 48

6173 49

6174 49

6175 49

6176 49

6178 49

6183 49

6184 49

6187 50

8

8000 Multilite 30

8001 31

8002 31

8005 31

8010 31

8015 32

8016 32

8018 32

8020 32

8022 32

8030 32

8100 33

8140 33

8141 33

8149 36

8150 36

8151 36

8152 36

8153 36

8154 36

page

8160 37

8165 37

8166 37

8170 37

8171 37

8172 37

8173 37

8174 38

8175 38

8176 38

8177 38

8178 38

8180 38

8184 38

8185 39

8186 39

8186 50

8187 39

8188 39

8189 39

8189 50

8190 39

8190 50

8300 41

8400 41

A

AC Masterpak 124

AC MH 108

AC OQ 2000 120

AC OTQ 1000 118

ARCM Arclite 108

ARG 108

ARL 108

ARM 108

ARS 108

B

BETA SP 60 128

C

CALOTTA QE 128

COND OQ 2000 120

COND OTQ 1000 118

GE Lighting 2

INDEX

page

CSA HAL 503 122

CSA Masterpak 124

CSA/DBX 101

CSA/H 106

CSA/H 107

CSA/M 127

CSA/S 127

E

EB EUROBAY 27

EF EUROFLOOD 116

ELI Elite 94

EST Eurostylo 74

F

FLAT 75

G

GUAR Halopak 122

GUAR Masterpak 124

H

HALOPAK 122

J

JKC Rods 112

JKC Fixtures 110

JKCB 111

JKCP 35 110

JKCP 50 110

JKCR 111

K

KUS 13

L page

LBL 109

LGL 109

LIVELIGHT 109

M

MAC 22

MAC/R 23

MAC/R AL 23

MAR/P 20

MAR/P SUPER 21

MASTERPAK 124

N

NAL 16

NAL 1001 18

NAL 1002 16

NAL 1003 16

NAL 1004 16

NAL 1006 16

NAL 1007 16

NAL 1008 16

NAL 1014 16

NAL 1023 18

NAL 1025 18

NAL 1026 16

NAL 1027 16

NAL 1030 18

NAL 1050 18

NAL 1110 18

NAL 1652 18

NBL 17

NBL 1002 17

NBL 1003 17

NBL 1004 17

NBL 1006 17

NBL 1007 17

NBL 1008 17

NBL 1014 17

NBL 1027 17

NPA 11

NPC 12

NPD 12

NPGR 12

NPGT 13

NPLT 13

NPP 9

page

NPQ 10

NPR 11

NPS 14

NPS/P 14

NPS/Q 14

NPT 11

NPW 7

NUA Nuplex 66

O

OQ 2000 120

OQS OQ 2000 120

OTQ 1000 118

OTQG 118

OTQP OTQ 1000 118

P

PIASTRA VUOTA QE 128

PK 11 Pocket 84

PTL Eurostreet 128

PTL Halopak 122

PTL LIVELIGHT 109

PTL Masterpak 124

Q

QE Eurostreet 126

QEAL 128

QEAS 128

QEGL 128

QEGS 128

R

REAT Arclite 108

REAT Masterpak 124

REAT OQ 2000 120

REAT OTQ 1000 118

S

Special Versions 26

STY Stylo 72

INDEX

GE Lighting 3

T page

T Transformers 105

TCGR 13

TOP/2D 99

TOP/2DR 98

TOP/A 102

TOP/DA 103

TOP/DBX 100

TOP/DF 103

TOP/F 102

TOP/GLASS 101

TOP/HA 106

TOP/HAG 106

TOP/HAG 107

TOP/LOUVER 101

TOP/M 104

TOP/MQA 107

TOP/MQF 107

TOP/RING 98

TOP/RING 101

V

VHA Halopak 122

VHA Masterpak 124

GE Lighting 4

INDEX

INDUSTRIAL LIGHTING

GE Lighting 5

N-PACK is the most classical range of batten luminaires.New in design and features, N-PACK is available in three basic batten versions(NPP, NPQ and NPW) and can be used with two different trunking systems (NALand NBL); a vast range of optical accessories is also available.Main features:

protection class IP 40 (IP 54 for NPW);

conforms to latest installation standards;

very fast installation thanks to special new devices and design solutions;

easy inspection and maintenance;

suitable for continuous mounting;

extremely reliable electric components;

polycarbonate lampholders with IP 40 or IP 54 protection on fluorescent tube

caps, as well;

complies with radio interference suppression legislation;

mark

N-PACK

GE Lighting 6

IP 54 Class: I

Mark:

Standards: CEI 34.21EN 60598-1

220V 50Hz

NPW/X 118 H 1 x F18 T8 27 HPF 620 343 1.40 NPWX118 7004256 4 560






HPF = with power factor correction

Tfn Tfgstandard operation in event of failure

NPW/X 136 70C 100CNPW/X 158 90C 130CNPW/X 236 70C 100CNPW/X 258 90C 130C

N and Lamp Tot. Absorbed Length Fixing Holes Weight Order Product Pack Qty.Type Type Power (W) Version L (mm) D (mm) (Kg) Code Code Box Pallet

NPW Fittings in packages of 4, without lamp.

91

50

91

116

L

D

GE Lighting 7

High IP 54 protection class luminaires for T8 fluorescent lamps.Cover and attachments can be fitted quickly without tools, cutting installation andmaintenance costs. Luminaires comply with radio interference suppression legislation(D.M. 10.04.84).The high IP 54 protection class of NPW luminaires makes them ideal for installation areaswhere fire risks are high (see CEI Standard 64.8 variant V2).Suitable also for electrical installation in AD-FT type hazardous areas, in the followingapplications: CLASS 0 rating ZR CLASS 1 rating ZR CLASS 3 rating Z2In these cases use NPGTW polycarbonate tubes, taking the following maximum surfacetemperatures on the outside of the housing into account:

Body and cover: bonderised cold-rolled steel (thickness 5/10 mm for body, 6/10 mm for cover) with a white epoxy-polyester powder paint finish. Cover is mounted on the body using special wing nuts.Lampholder: polycarbonate, fitted to the body by a safety clip; complete with soft LOMOD ring nuts to ensure an effective seal and prevent any danger of the lamp failing;the rotor system anables continuous mounting of the luminaires.Control gear and electric circuit: wired for 220V 50Hz using 0.50 mm2 sized cables withsilicon sleeves; power factor correction using explosion-proof capacitor built-in dischargeresistor; terminal block with 2,5 mm2 clamping screws.The control gear circuit wiring islocated on a removable sheet plate located inside the luminaire.Cable entry: using special hole in body through D18 grommet.Seals: expanded polyurethane resin between the body and cover plate; rubber betweenlampholder and luminaire body.SPECIAL APPLICATIONS: see page 24 - 25 - 26

N-PACK NPW

IP 40 Class: I

Mark:


230V 50Hz

91

50

91

116

D

L

GE Lighting 8

N-PACK NPP

Luminaires for T8 fluorescent lamps for ceiling or trunking installation.Cover and attachments can be fitted quickly without tools, cutting installation andmaintenance costs.Body and cover: bonderised cold rolled 5/10 mm sheet steel with white epoxy-polyesterpowder paint finish. The cover is clipmounted to the body.Lampholder: polycarbonate, fitted to the body by a safety clip; complete with ring nuts as a further safety feature to guaranteee IP 40 and to prevent the lamp from fall; the rotorsystem enables continuous mount of luminaires.Starter: positioned to the side of the body, allowing routine maintenance operationswithout need to remove lamp or accessories.Control gear and electric circuit: 230V 50Hz wired with 0.75 mm2 section heat-resistant(HT 90C), fire-retardant cable in compliance with CEI 20-22/II, with explosion-proofcapacitor with built-in discharge resistor in the HPF version, with power factor correction;terminal block with 2,5 mm2 clamping screws.Cable entry: through special hole in body through D18 grommet or through knock-outs atthe end of the fittings.SPECIAL APPLICATIONS: see page 24 - 25 - 26.

NPP 115 L 1 x F15 T8 22 470 315 1.10 NPP115L 7004224 1 464

NPP 118 H 1 x F18 T8 27 620 470 1.30 NPP118H 7004225 1 464

NPP 118 L 1 x F18 T8 27 620 470 1.30 NPP118L 7004227 1 464

NPP 130 H 1 x F30 T8 39 925 605 1.60 NPP130H 7004229 1 232

NPP 130 L 1 x F30 T8 39 925 605 1.60 NPP130L 7004230 1 232

NPP 136 H 1 x F36 T8 45 1230 800 2.10 NPP136H 7004233 1 232

NPP 136 L 1 x F36 T8 45 1230 800 2.10 NPP136L 7004235 1 232

NPP 158 H 1 x F58 T8 72 1530 800 2.70 NPP158H 7004238 1 232

NPP 158 L 1 x F58 T8 72 1530 800 2.70 NPP158L 30059 1 236

NPP 218 H 2 x F18 T8 45 620 470 1.40 NPP218H 7004240 1 300

NPP 218 L 2 x F18 T8 45 620 470 1.40 NPP218L 7004242 1 300

NPP 236 H 2 x F36 T8 90 1230 800 3.10 NPP236H 7004244 1 150

NPP 236 L 2 x F36 T8 90 1230 800 3.10 NPP236L 7004246 1 150

NPP 258 H 2 x F58 T8 144 1530 800 4.30 NPP258H 7004249 1 150

NPP 258 L 2 x F58 T8 144 1530 800 4.30 NPP258L 30068 1 150

HPF = with power factor correction LPF = without power factor correction


NPP Fittings single packed, complete with lamp.LPF

HPF

LPF

HPF

LPF

HPF

LPF

HPF

LPF

HPF

LPF

HPF

LPF

HPF

LPF

NPP/X 118 H 1 x F18 T8 27 620 470 1.30 NPPX118H 7004226 4 560

NPP/X 118 L 1 x F18 T8 27 620 470 1.30 NPPX118L 7004228 4 560

NPP/X 136 H 1 x F36 T8 45 1230 800 2.10 NPPX136H 7004234 4 280

NPP/X 136 L 1 x F36 T8 45 1230 800 2.10 NPPX136L 7004236 4 280

NPP/X 158 H 1 x F58 T8 72 1530 800 2.70 NPPX158H 7004239 4 280

NPP/X 158 L 1 x F58 T8 72 1530 800 2.70 NPPX158L 30060 4 280

NPP/X 218 H 2 x F18 T8 45 620 470 1.40 NPPX218H 7004241 4 560

NPP/X 218 L 2 x F18 T8 45 620 470 1.40 NPPX218L 7004243 4 560

NPP/X 236 H 2 x F36 T8 90 1230 800 3.10 NPPX236H 7004245 4 280

NPP/X 236 L 2 x F36 T8 90 1230 800 3.10 NPPX236L 7004247 4 280

NPP/X 258 H 2 x F58 T8 144 1530 800 4.30 NPPX258H 7004250 4 280

NPP/X 258 L 2 x F58 T8 144 1530 800 4.30 NPPX258L 30075 4 280

NPP/X Fittings in pack of four, without lamp.HPF

LPF

HPF

LPF

HPF

LPF

HPF

LPF

HPF

LPF

HPF

LPF

N-PACK NPP

GE Lighting 9

NPQ/X 118 H 1 x F18 T8 27 HPF 620 1.20 NPQX118 7004251 4 560







N and Lamp Tot. Absorbed Length Weight Order Product Pack Qty.Type Type Power (W) Version L (mm) (Kg) Code Code Box Pallet

NPQ Fittings in packages of 4, without lamp. Fitting does not include NAL 1652 terminal socket.

Quick mechanical fitting

Quick electrical fitting

IP 40 Class: I

Mark:


230V 50Hz

91

50

91

116

L

N-PACK

GE Lighting 10

N-PACK NPQ

Version without cover specially designed for mounting on NAL or NBL trunking using amechanical and electrical clip system that requires no tools.The electrical connection uses a NAL 1652 terminal socket accessory previously fitted to theNAL or NBL trunking (see page 18).Body and cover: cold-rolled bonderised 5/10 mm sheet steel with a white epoxy-polyesterpowder paint finish.Lampholder: polycarbonate, fitted to the body by a safety clip; complete with ring nuts to ensure IP 40 and provide a further safety measure against the falling lamp; the rotorsystem enables continuous mounting of luminaires.Starter: position on side of body, allowing routine maintenance operations withoutremoving lamp or accessories.Control gear and electrical circuit: 230V 50Hz wired with 0,75 mm2 section heat-resistant (HT 90C), fire-retardant cable in compliance with CEI 20-22/II, with explosion-proof capacitor and built-in discharge resistor (HPF version) with power factor correction.Quick electric fitting: the system uses a terminal plug mounted in the body for quickelectrical connection with the NAL 1652 terminal socket (not included) previously installedon trunking.Quick mechanical fiting: the system comprises a ring nut which forms an integral part ofthe body, a catch pin coaxial to the ring nut, and a spring clip which fastens to the trunking.Turn the right nut and pin to different positions to fit/release the luminaire or mountaccessories.SPECIAL VERSIONS: see page 24 - 25 - 26.

NPT 2 1 x 18 620 0.40 NPT2 32059 6

NPT 4 1 x 36 1230 0.80 NPT4 7004205 6

NPT 5 1 x 58 1530 1.00 NPT5 7004308 6

NPT 22 1/2 x 18 620 0.60 NPT22 32061 6

NPT 24 1/2 x 36 1230 1.30 NPT24 7004206 6

NPT 25 1/2 x 58 1530 1.60 NPT25 7004309 6

With Length Weight Order Product PackType Luminaire (mm) (Kg) Code Code Qty.



NPT Metal reflectorFor NPW NPP NPQ.Distributes light entirely downwards.Bonderised pressed 5/10 mm steel, with epoxy-polyester powder paint finish.Possibility of continuous mounting with NPLT alignment clip.

NPR Slotted metal reflectorFor NPW NPP NPQ.Shape and dimensions of reflector results high efficiency.Slots prevent tunnel effect and eye strain when shifting vision from bright (work surface)to dim areas (ceiling).Bonderised cold-pressed 5/10 mm steel with white epoxy-polyester paint finish.Possibility of continuous mounting with NPLT alignment clip.

NPR 4 1/2 x 36 1230 1.30 NPR4 7004203 6

NPR 5 1/2 x 58 1530 1.60 NPR5 7004204 6

NPR 24 2 x 36 1230 1.60 NPR24 32070 6

NPR 25 2 x 58 1530 2.00 NPR25 7004307 6

NPA Asymmetric metal reflectorFor NPW NPP NPQ.Special light distribution of reflector makes it particularly suitable for asymmetric lightingAvailable in single-lamp version only, made of bonderised 5=10 mm pressed sheet steelwith white epoxy-polyester powder paint finish.Possibility of continuous mounting with NPLT alignment clip.

NPA 4 1 x 36 1230 0.80 NPA4 32072 6

NPA 5 1 x 58 1530 1.00 NPA5 32073 6

94 112

128 170

112

240

112

170

148

81

GE Lighting 11

N-PACK accessories

With Length Weight Order Product PackType Luminaires (mm) (Kg) Code Code Qty.

NPGR Metal louvreClip fits on NPT twin-lamp reflectors and NPR single-lamp reflectors on single and twin-batten luminaires. Ends are closed off by two clip-fit end caps (supplied). Bonderised pressed sheet steel with white epoxy-polyester powder paint finish.Combination of louvre and reflector results effective lamp screening while maintaining lightoutput.Possibility of continuous mounting of luminaires by NPLT alignment clip instead of clip-fitend caps.

NPGR 24 NPR 4-NPT 24 1235 0.80 NPGR24 7004311 6

NPGR 25 NPR 5-NPT 25 1535 1.00 NPGR25 7004312 6

112

170


NPC Methacrylate prismatic diffuserFor NPP NPQ.Designed for twin-lamp luminaires and supplied complete with flat metal reflector and clip-fit end caps.Features longitudinal reeding along the sides and prismatic base.

NPD Methacrylate diffuserFor NPP NPQ.Designed for single-lamp luminaires, features internal longitudinal prismatic reeding.Mount with two clip-fit end caps included in pack.

NPC 24 NPP-NPQ 2 x 36 1235 1.60 NPC24 32178 6NPC 25 NPP-NPQ 2 x 58 1535 1.90 NPC25 32163 6

NPD 2 NPP-NPQ 1 x 18 625 0.20 NPD2 32075 6

NPD 3 NPP-NPQ 1 x 30 930 0.28 NPD3 32077 6

NPD 4 NPP-NPQ 1 x 36 1235 0.35 NPD4 32079 6

NPD 5 NPP-NPQ 1 x 58 1535 0.42 NPD5 32088 6

108

150

95

55


GE Lighting 12

N-PACK accessories

NPGT Overtube (NPP NPQ)NPGTW Overtube (NPW)Shatter-prof self-extinguishing polycarbonate; reeding (NPGT version) or smooth (NPGTW version) interior finish, for POPACK installation in medium/large commercialareas. Supplied complete with 2 ring nuts for mounting on lampholders.Replace universal starter (FSU) with Rapid safety starter (VIT 2) when using overtube.

NPGT 2 NPP-NPQ 1/2 x 18 620 0.13 NPGT2 32090 12/1

NPGT 3 NPP 1 x 30 925 0.19 NPGT3 32092 12/1



NPGTW 2 NPW 1/2 x 18 620 0.12 NPGTW2 32099 12/1

NPGTW 4 NPW 1/2 x 36 1230 0.22 NPGTW4 32101 12/1

NPGTW 5 NPW 1/2 x 58 1530 0.27 NPGTW5 32102 12/1


Order Product PackType Code Code Qty.

KUS Opal methacrylate diffuser elementsModular elements 306 mm long, for complete screening of T8 fluorescent tubes, ensuringhigh standards of visual comfort and a smart appearance.Elements are mounted directly on the fluorescent tube in single-lamp luminaires by spring-loaded clip-fit system

KUS KUS 32105 4

No. elements per fitting: 1 x 18 : 2 pcs, 1 x 30: 3 pcs, 1 x 36: 4 pcs, 1 x 58: 5 pcs

110

74

TCGR TCGR 32135 1

NPLT NPLT 32136 100

TCGR End capThermoplastic end cap for NPT twin-lamp and NPR single-lamp reflectors.

NPLT Alignment clip for NPT NPR NPA reflectorsClick-fit thermoplastic alignment clip.



GE Lighting 13

N-PACK accessories


NPS Wire guardElectrically welded iron wire with polished galvanized finish. Hinge opening for lamp changes.Available in two versions:NPS/Q with nickel-plated brackets for mounting on NPQ and NPW luminaires by quickmechanical mount device.NPS/P with nickel-plated steel brackets fitted to rear of NPP and NPW fittings.

NPS/P 2 NPP-NPW 1 x 18 620 0.30 NPSP2 32110 6

NPS/P 4 NPP-NPW 1 x 36 1230 0.40 NPSP4 32112 6

NPS/P 5 NPP-NPW 1 x 58 1530 0.50 NPSP5 32113 6NPS/P 22 NPP-NPW 2 x 18 620 0.40 NPSP22 32116 6

NPS/P 24 NPP-NPW 2 x 36 1230 0.60 NPSP24 32120 6NPS/P 25 NPP-NPW 2 x 58 1530 0.70 NPSP25 32122 6

NPS/Q 2 NPQ - NPW 1 x 18 620 0.30 NPSQ2 32124 6


NPS/Q 5 NPQ - NPW 1 x 58 1530 0.50 NPSQ5 7004306 6NPS/Q 22 NPQ - NPW 2 x 18 620 0.40 NPSQ22 32128 6



NPS/P

NPS/Q

110 110

65 128

GE Lighting 14

N-PACK accessories

NBL 1014

NAL 1050/1100

NBL 1004

NBL 1004

NAL 1110

NAL 1030

NAL 1023

NBL 1027NBL 1003

NBL 1006

NBL 1007

NBL 1008

NAL 1001

NAL 1025

NAL 1652

NBL 1002

IP 40

Load-bearing ceiling-mounted or suspended trunking system for lighting installations. Available in two versions: NAL and NBL.Load-bearing body is made of bondarised 8/10 mm sheet steel with white epoxy-polyester powder paint finish.Various types of luminaires can be installed using the following accessories: NAL 1652 terminal socket for rapid electrical fitting of NPQ series luminaires. NAL 1023 suspension bracket for NPP, NPW, MARINER, MAC and other luminaires with mounting holes min. 5 mm.Follow the instructions supplied in the pack.

NBL systemLimit load conditions:Admissible deflection F = L/300Maximum load q max = 6 Kg/mMax. distance between suspension centres L max = 2000 mm

46

3268

26

3258

NAL 1014 NAL 1026 NAL 1050/1100

NAL 1004

NAL 1004

NAL 1110

NAL 1030

NAL 1023

NAL 1027

NAL 1003

NAL 1006

NAL 1007

NAL 1008

NAL 1001

NAL 1025

NAL 1652

NAL 1002

NAL, NBL

GE Lighting 15

NAL systemLimit load conditions:Admissible deflection F = L/300Maximum load q max = 6 Kg/mMax. distance between suspension centres L max = 3000 mm

NAL 1000 1000 x 68 x 46 1.380 NAL1000 32559 4

NAL 2000 2000 x 68 x 46 2.760 NAL2000 7004209 4

NAL 3000 3065 x 68 x 46 4.140 NAL3000 7004210 4

Dimensions Weight Order Product PackType L x B x H (mm) (Kg) Code Code Qty.

NAL Trunking section.

NAL 1002 250 x 66.5 x 43.5 0.455 NAL1002 7004316 20/1

NAL 1002 Straight joint.

NAL 1003 15 x 70 x 47 0.020 NAL1003 32566 100/1

NAL 1003 End cap.

NAL 1004 38 x 38 x 40 0.040 NAL1004 7004317 50/1

NAL 1004 Suspension bracket for hanger or NAL 1025.

NAL 1006 188 x 188 x 47,5 0.450 NAL1006 32570 10/1

NAL 1006 Die cast aluminium L joint.

NAL 1007 298 x 188 x 47,5 0.590 NAL1007 32576 10/1

NAL 1007 Die cast aluminium T joint..

NAL 1008 298 x 298 x 47,5 0.730 NAL1008 32580 5/1

NAL 1008 Die cast aluminium X joint.

NAL 1014 130 x 130 x 70 0.250 NAL1014 32586 5/1

NAL 1014 Die cast aluminium up/down joint.

NAL 1026 38 x 38 x 20 0.035 NAL1026 7004318 100/1

NAL 1026 Ceiling bracket.

NAL 1027 10 x 65 x 43 0.003 NAL1027 32589 100/1

NAL 1027 Wire clip.

NAL system

GE Lighting 16


NBL 1000 1000 x 58 x 26 0.900 NBL1000 32594 4

NBL 2000 2000 x 58 x 26 1.800 NBL2000 7004211 4

NBL 3000 3065 x 58 x 26 2.700 NBL3000 7004212 4

NBL Trunking section.

NBL 1002 200 x 55,5 x 23,5 0.235 NBL1002 7004215 24/1

NBL 1002 Straight joint..

NBL 1004 42 x 61,5 x 63 0.080 NBL1004 7004320 20/1

NBL 1004 Trunking suspension bracket for NAL 1025 or hanger.

NBL 1003 15 x 59 x 27 0.012 NBL1003 32595 100/1

NBL 1003 End cap.

NBL 1006 153 x 153 x 27,5 0.350 NBL1006 32596 10/1

NBL 1006 Die cast aluminium L joint.

NBL 1007 238 x 153 x 27,5 0.480 NBL1007 32597 10/1

NBL 1007 Die cast aluminium T joint.

NBL 1008 238 x 238 x 27,5 0.650 NBL1008 32598 5/1

NBL 1008 Die cast aluminium X joint.

NBL 1014 100 x 100 x 60 0.140 NBL1014 32600 5/1

NBL 1014 Die cast aluminium up/down joint.

NBL 1027 10 x 56 x 25 0.002 NBL1027 32614 100

NBL 1027 Wire clip.

GE Lighting 17

NBL system


NAL 1001 1800 x 50 x 12 0.250 NAL1001 32624 30

Dimensions Weight Order Product PackType x L (mm) (Kg) Code Code Qty.

NAL 1001 White self-extinguishing PVC cover strip.

NAL 1023 20 x 45 x 35 0.030 NAL1023 32621 100/2

NAL 1023 Suspension bracket for 5 mm light fitting.

NAL 1025 25 x 25 x 80 0.065 NAL1025 32617 100/1

NAL 1025 Trunking suspension chain.

NAL 1030 L max 3000 0.750 NAL1030 7004213 5/1

NAL 1030 Power supply set.

NAL 1652 45 x 35 x 25 0.003 NAL1652 32615 50/1

NAL 1652 Terminal socket for NPQ.

NAL 1050 13 x 500 0.340 NAL1050 7004214 12/1

NAL 1100 13 x 1000 0.560 NAL1100 7004319 12/1

NAL 1050 NAL 1100 White steel hanger.

NAL 1110 13 x 1000 0.560 NAL1110 31753 20/1

NAL 1110 White steel hanger extension.

GE Lighting 18

General accessories NAL - NBL

Reflector with thick paintworkThe sheet reflector is finished with a coat of high-electric insulating paint. The extra-thick paintwork eliminates the hazards of sharp edges and rust.

Environmental friendlyAll plastic materials used are recyclable.Safety starter

Located away from lamp cathodes, in compliance with recent standardproposals requiring a max. temperature of 80C of the starter housing. It can bereplaced without removal of the reflector.

SealingThe special shaping of the diffuser guarantees a perfect seal and easycentering with the body.The long-life polyurethane sealing foam is applied using ecological methods,without the use of freon gas.

Switching fuseThe terminal block with switching fuse (MAR/P version) rapidly insulates andlocates the faulty lamp, thereby ensuring smooth and constant running of theoverall lighting system.

Reflector mounting without toolsThe internal reflector is easily mounted; just turn the pawl 90.The reflector remains attached to the fitting by suspension cords duringmaintenance operations.

1

1

2

2

3

3

4

4

5

5

6

6

7

GE Lighting 19

MARINER

Nylon clips with steel jointsThis combination of materials was determined by stress analysis studies, whichidentified the most suitable material for each function: stainless steel for partsunder cutting stress, fibreglass strenghtened nylon for parts demanding a highdegree of elasticity.The set also includes: tamper-proof securing screw system; suspended diffuser for maintenance; stainless steel clips on request.

Mariner offers a new complete range of waterproof luminaires:MAR/P and MAR/P Super.These fittings present a degree of product diversity which isperfectly capable of adapting to the most specific applicationdemands.The special technical features and irresistible quality of Lexan

polycarbonate produced by General Electric make the Marinerline worthy candidate for the leadership in IP 65 total protection.

IP 65 Class: I

Mark:

Standards:CEI 34.21EN 60598-1

230V 50Hz

165

105105

105

L

D


MAR/P 136/236 90C 120CMAR/P 158/258 100C 135C

MAR/P 118 H 1 x F18 T8 27 HPF - FUS 660 390 6 1.70 MARP118H 7004173 1 126






HPF = with power factor correction FUS = with fuse

N and Lamp Tot. Absorbed Length Fixing Holes N of Weight Order Product Pack Qty.Type Type Power (W) Version L (mm) D (mm) Clips (Kg) Code Code Box Pallet

MAR/P Fitting packed singly, without lamp.

GE Lighting 20

MARINER MAR/P series

For resistance to chemical agents and other construction materials see page 168.

Waterproof ceiling fittings for T8 fluorescent lamps (T12 for twin lamps), for total protectionagainst the penetration of foreign objects, water jets from any direction and accidentalshocks.Flame and combustion resistance in compliance with CEI 34.21 EN 60598-1, totallyself-extinguishing V2.Ideal for installation in humid and/or dusty areas or for exterior use.Perfect for AD-FT ambients with inflammability temperature > 150C.Body: shatterproof Lexan polycarbonate, grey RAL 7035, self-extinguishing V2; featurespolyurethane foam seals applied without the use of freon.Cover: transparent shatterproof self-extinguishing V2 Lexan polycarbonate, injectionmoulded anti-ageing UV-stabilized, with high-luminous efficacy linear prismatic reeding onthe inside. Completely smooth on the outside for easy cleaning.Clips: fibreglass-reinforced nylon, with self-retaining hinged stainless steel joints. Supplied also with steel screws for tamper-proof fitting. (Stainless steel clips are availableon request.)Reflector: bonderised shaped sheet steel with high-reflection white stoved epoxy-polyester powder paint finish. Wireing is mounted to it. Remains attached to the fitting bysuspension cords during maintenance.Control gear and electric circuit: 230V 50Hz wired with 0.75 mm2 section heat-resistant(HT 90C), fire-retardant cable in compliance with CEI 20-22/II, with explosion-proofcapacitor, with built-in discharge resistor in the HPF version, with power factor correction;three-phase terminal block with switching fuse and clamping screws for conductors up to2.5 mm2.Standard ballasts screw-fitted.Max. exterior surface temperature of casing:

Standard accessories: fittings supplied with D 21 mm grommet, cable clamp PG 13.5 andtwo suspension rings. Fittings may be installed on trunking with NAL 1023 suspensionbracket.SPECIAL VERSIONS: the luminaires can be equipped with low-loss ballast (BP), electronicballast (EB), emergency version (EES), double ignition (DA) or cablings in double insulation:see pages 24-25-26.

IP 65 Class:

Standards: CEI 34.21 - EN

60598-1

230V 50Hz

IP 65 sealed ceiling fittings for T8 fluorescent lamps (T12 for twin lamps), for total protectionagainst the penetration of foreign objects, water jets from any direction and accidentalcontact.Flame and combustion resistant in compliance with CEI 34.21 EN 60598-1, totallyself-extinguishing V2.Manufactured in compliance to CEI 64-2 for installation in electrical systems in AD-FT typehazardous areas with inflammability temperature < 150C, in the following applications: CLASSE 0 rating ZR CLASSE 1 rating ZR CLASSE 2 with electro-conductive (C2 E) and non-conductive (C2 NE) powdwers CLASSE 3 rating Z2Technical features as per MAR/P series, with the following variations:Control gear and electric circuit: 230V 50Hz wired double-insulated with low-lossballast, 1 mm2 section heat-resistant (HT 90C), fire-retardant cable in compliance with CEI 20.22/II and safety starter VIT2 for automatic cut-out of burned out or faulty lamps.

Max. exterior surface temperature of casing:

MAR/P-SUPER 118 1 x F18 T8 24 * 660 390 6 1.70 MARPSUPER118 30285 1 126






N and Lamp Tot. Absorbed Length Fixing Holes N of Weight Order Product Pack Qty.Type Type Power (W) Version L (mm) D (mm) Clips (Kg) Code Code Box Pallet

MAR/P-SUPER Single pack, without lamp.

MAR/P SUPER series


MAR/P SUPER 136/236 80C 120CMAR/P SUPER 158/258 90C 120C

MARINER SERIES ACCESSORIES

For ceiling N ofType lamps Clipps

STAINLESS STEEL CLIP MAR 118/218 1 x 18/2 x 18 6



Stainless steel clips

GE Lighting 21

MARINER

* Double-insulated with low-loss ballast, power correction factor and with safety starter for automatic cut-out.


IP 65 Class:

Mark:

Standards:CEI 34.21EN 60598-1

230V 50Hz

MAC 118 H 1 x F18 T8 27 HPF 645 500 1.60 MAC118H 7004287 1 300

MAC 136 H 1 x F36 T8 45 HPF 1265 800 2.30 MAC136H 7004288 1 150

MAC 158 H 1 x F58 T8 72 HPF 1565 1100 3.00 MAC158H 7004289 1 150

MAC 218 H 2 x F18 T8 45 HPF 645 500 2.00 MAC218H 7004290 1 240

MAC 236 H 2 x F36 T8 90 HPF 1265 800 3.80 MAC236H 7004291 1 120

MAC 258 H 2 x F58 T8 144 HPF 1565 1100 4.80 MAC258H 7004292 1 120



MAC Fittings packed singly, without lamp.

125

61

125

125

D

L


MAC

GE Lighting 22

Waterproof luminaires for T8 tubular fluorescent lamps offering total protection against theentry of foreign objects, jets of waters from any direction and accidental contact (Class II).Flame and combustion resistant in compliance with CEI 34.21 EN 60598-1.Suitable for installation in damp and/or dusty environments as well as for exterior use. Theentire series complies with radio interference legislation (DM 10.04.84), making it suitable forinstallation in residental areas. The luminaires are supplied with 38 mm polycarbonateprotective tube and VIT 2 starter (FS 2 for MAC 218 version).Body and cover: fibreglass reinforced polyester.Lampholder: self-extinguishing polycarbonate for T8 tubular fluorescent lamps, complete with ring nuts, lampholders clip fit over a seal in cover tube seating.Control gear and electric circuit: wired for 230V 50Hz using 0.5 mm2 section cables withsilicone insulation, power factor correction (HPF) using explosion-proof capacitor with built-in discharge resistor; terminal block with 2.5 mm2 clamping screws; VIT 2 safety starter forautomatic cut-out of burned out or faulty lamps (FS 2 starter for MAC 218 version). Starters are accessible from outside the luminaire by removing the starter compartment capin cover.Standard accessories: luminaires are supplied complete with grommet D 21 mm, cableclamp PG 13.5 and two suspension rings.All luminaires can be installed on trunking system using accessory NAL 1023 (see page 18).SPECIAL VERSIONS: see pages 24-25-26..

MAC/R 2 MAC 118 650 0.60 MACR2 32522 5

MAC/R 4 MAC 136 1255 1.00 MACR4 7004313 5

MAC/R 5 MAC 158 1555 1.30 MACR5 7004208 5

MAC/R 22 MAC 218 650 0.80 MACR22 33058 5

MAC/R 24 MAC 236 1160 1.40 MACR24 7004314 5

MAC/R 25 MAC 258 1460 1.80 MACR25 7004315 5

With Length Weight Order Product PackType Luminaire L (mm) (Kg) Code Code Qty.

130

235

170

130

MAC/R 2 AL MAC 118 650 0.36 MACR2AL 33039 5






MAC/R AL

MAC/R

GE Lighting 23

MAC/R reflectors

Using the reflectors on MAC fittings results better efficiency in case of high roofs or locallightings.MAC/R: cold-profiled steel with white stoved epoxy-polyester powder paint finish.MAC/R AL: polished finish aluminium suitable for use in corrosive environments.The reflectors are attached to the luminaires with stainless steel springs (suppliedtogether).

EB VERSION WITH ELECTRONIC BALLAST

The electronic ballast is a high frequency (43 kHz) power supply device for fluores-cent lamps, which substitutes the standard magnetic ballast, starter and powerfactor correction capacitor.The electronic ballasts are compatible with normal T8 ( 26 mm) tubular fluores-cent lamps.The ideal combination is obtained with the use of POLYLUX XL high colour rendition factor tubes, ensuring low running costs and excellent colour rendering. Compliance with European standards EN 60928, IMQ and VDE mark certificationand the absence of radio interference thanks to the RFI filter make fittingsequipped with the electronic ballast perfect for installation in environments subjectto special regulations, such as data processing centres, factories, public premisesand hospitals.Main characteristics of the ELECTRONIC BALLAST: energy saving up to 23% and longer lamp life up to +50%; the electronic ballast is protected against overvoltage, short circuit and polarity

inversion; instant lamp starting, high degree of light quality and eye comfort thanks to

elimination of flickering and the stroboscopic effects; high power factor (cos j ) of circuit, without need for power factor correction

capacitors; protective circuit in the event of anomalous functioning (e.g. burn-out lamp); to

restore main circuit, turn off mains switch, change lamp, then turn back on after 10 seconds;

possibility of DC power supply; absence of irradiated magnetic fields, in compliance with current legislation; silent operation; starting even at low temperatures (-15C); no need for starter.

LUMINOUS FLUX OF A FLUORESCENT LAMP IN RELATION TOPOWER SUPPLY FREQUENCY

TABLE OF APPLICATIONSeries 5000 NPP/NPQ MARINER MAC NPW

Catalogue No REAT REAT REAT REATEL 1 x 36 EL 1 x 58 EL 2 x 36 EL 2 x 58

1 x 18 1 x 36 1 x 58 2 x 18 2 x 36 2 x 58 4 x 18

Voltage 220/240V 220/240V 220/240V 220/240VPower Supply 207/254V 207/254V 207/254V 207/254VVoltage TolerancePower Supply 50/60 Hz 50/60 Hz 50/60 Hz 50/60 HzFrequencyOperating 43 KHz 50 KHz 50 KHz 50 KHzFrequencyPower > 0.95 > 0.95 > 0.95 > 0.95FactorOperating -15 +50C -15 +50C -15 +50C -15 +50CTemperatureMax. Relative 95% 95% 95% 95%Humidity (ta 25C) (ta 25C) (ta 25C) (ta 25C)Loos 2.2W 2.5W 6W 9WWeight 0.275 kg 0.276 kg 0.500 kg 0.500 kg

TRADITIONAL EQUIPMENT DIFFERENCEEQUIPMENT WITH ELECTRPNIC

BALLAST110

108

106

104

102

1005 1 2 3 5 10 20 30 50 100

% d

i effi

cien

za lu

min

osa

Frequenza kHz

COMPARISON OF ECONOMICS Considering, for example, a 2x58W luminaire, the difference between thetraditional equipment and that with an electronic ballast can be summarized on thefollowing table:

*The data refers to the General Electric standard fluorescent lamps with regard toa typical installation with at least 3 hours of starting cycles (as it occurs forexample in commercial environments). In case the Genereal Electric Polylux XLfluorescent lamps are used, the life of the fluorescent lamps ranges from 15,000hours (traditional equipment) to 18,000 hours (for equipment with electronicballast).

Consumed Power (W) 142 108 -34Annual Operation (h) 4000 4000 -Cost of Energy (USD/KWh) 0.12 0.12 -Annual Energy Cost (USD) 68.16 51.84 -16.32Average Surplus Price for Version

0 36.00 +32.00with Electronic Ballast (USD)Average Life of the Lamp (h)* 9000 13000 +45%Annual Cost of Lamp

12.20 8.00 -4.80Maintenance (USD)

ANNUALSAVINGS ()

TOTAL ENERGY80.36 59.84 -20.52

+ MAINTENANCE COST (USD)

TIME OF DEPRECIATION OF THESURPLUS PRICE FOR VERSION WITH 21ELECTRONIC BALLAST (MONTHS)

SPECIAL VERSIONS

GE Lighting 24

Frequency kHz

% o

f lig

htin

g ef

ficie

ncy

EES VERSION FOR ELECTRONIC EMERGENCY SERVICE

The EES (Electronic Emergency Service) is an autonomous system for fluorescentlamps in an emergency situation. The system comprises a power supply unit of hermetically sealed long-life Nickel-Cadmium batteries, particulalrly resistant tohigh temperatures (70C); an electronic inverter unit; and a LED, for indicating battery condition (IEC standard 598-2-22)Luminaires are supplied with an EES for PERMANENT lighting; the lamp is powered alternatively by the mains voltage, or by the batteries in case of mainsvoltage cut off.The inverter incorporates an inhibition circuit to prevent emergency operationwhile mains voltage is on.In twin-batten luminaires, only one lamp is connected to the EES.This solution has the following advantages: damage-free operation without all lamps operating, e.g. in the event of lampfailure; protection against total battery discharge.

VIT VERSION WITH RAPID SAFETY STARTER VIT 2

All luminaires between 18W and 58W (except for 2 x 18W) can be equipped withrapid safety starters, which not only cut starting time by half compared to a conventional starter, but also automativally cut out burned-out or faulty lamps. Simply press the red button on the top of the starter to re-activate the electric circuit.The cut-out device protects both the power supply and the starter alike. Thanks to the above features, the VIT 2 starter lasts four times longer than an ordinary starter.Features: can be used in all circuits with a traditional power supply; operates with all fluorescent lamps from 18W to 65W; operates regularly with ambient temperatures rating between -20C to +80C in

36W to 58W lamps, and between +5C and +80C in 18W to 30W lamps.

FSE VERSION WITH FS.E ELECTRONIC STARTER

The FS.E starter was designed for ultra-rapid starting of fluorescent lamps in lessthan 1/2 second (x 20 cycles) without flickering.The operation principle is based on two wave-shaped semi-circles: during the first semi-circle, the starter pre-heats the lamp cathodes; during the second semi-circle, the starter discharges the pulse for starting, until the lamps lights up.The FS.E starter automatically turns off burned out or faulty lamps. To restore thecircuit, simply turn off the mains switch, replace the lamp, then turn back on after10 seconds.Features: can be used with inductive circuits for powering traditional T12 fluorescent

lamps (20W to 65W), T8 lamps (15W to 58W), compact lamps (18W to 36W), 2D lamps (21W, 28W, 38W);

starting in less than 1/2 second; regular operation in ambient temperatures between -20C and +80C.

DA VERSION WITH DOUBLE STARTING

For partial use of the light fitting in special light or working conditions, all twin-batten luminaires (except 2 x 18W) can be equipped with different starters for eachlamp. (4-pole terminal with separate phases and neutral in common.)

BP VERSION WITH LOW-LOSS BALLAST

Versions with low-loss ballasts offer ballast losses of 6W (instead of 9W) with36W lamps, and 8W (instead of 13W) with 58W lamps. Enhanced lighting efficiency with standard lamps (> 74 lm/W) results considerablesavings in energy and a lesser load to the entire system, compared to versions withstandard ballast, that reaches max. 67 lm/W.

18 25 90 24 3.6 436 20 60 24 3.6 458 17 60 24 6 4

* Ave. value emitted during discharge.

EES AVAILABILITYSerie 5000

NPP/NPQ MARINER MAC NPW

1 x 18 1 x 36 1 x 58 2 x 18 2 x 36 2 x 58 4 x 18

Consumption of Low-Loss6 8 12 16

Ballast

LAMP WATTAGE 1 x 36W 1 x 58W 2 x 36W 2 x 58W

LAMP EMITTED EMERGENCY RECHARGE BATTERIESPOWER FLUX* OPERATION TIME (V) (Ah)(Watts) % of rated (minutes) (hours)

value

SPECIAL VERSIONS

GE Lighting 25

NPW/X 136 H BP NPWX136HBP 32379 4NPW/X 158 H BP NPWX158HBP 32383 4NPW/X 236 H BP NPWX236HBP 32389 4NPW/X 258 H BP NPWX258HBP 32154 4

NPP 136 H BP NPP136HBP 31790 1NPP 158 H BP NPP158HBP 32410 1NPP 236 H BP NPP236HBP 31664 1NPP 258 H BP NPP258HBP 32413 1

NPQ 136 H BP NPQ136HBP 32446 1NPQ 158 H BP NPQ158HBP 32447 1NPQ 236 H BP NPQ236HBP 32448 1NPQ 258 H BP NPQ258HBP 32450 1

MAR/P 136 H BP MARP136HBP 30261 1MAR/P 158 H BP MARP158HBP 30265 1MAR/P 236 H BP MARP236HBP 30273 1MAR/P 258 H BP MARP258HBP 30284 1

MAC 136 H BP MAC136HBP 32475 1MAC 158 H BP MAC158HBP 32476 1MAC 236 H BP MAC236HBP 31661 1MAC 258 H BP MAC258HBP 32187 1

BP - Fittings with low-loss ballast and fuse, without lamp. EB - Fittings with electronic ballast ( cos j 0.97), without lamp.

NPW/X 118 EB NPWX118EB 32390 4NPW/X 136 EB NPWX136EB 32393 4NPW/X 158 EB NPWX158EB 32394 4NPW/X 218 EB NPWX218EB 32402 4NPW/X 236 EB NPWX236EB 30083 4NPW/X 258 EB NPWX258EB 30086 4

NPP 118 EB NPP118EB 32415 1NPP 136 EB NPP136EB 32421 1NPP 158 EB NPP158EB 33062 1NPP 218 EB NPP218EB 32432 1NPP 236 EB NPP236EB 30066 1NPP 258 EB NPP258EB 30067 1

NPQ 118 EB NPQ118EB 32455 1NPQ 136 EB NPQ136EB 32458 1NPQ 158 EB NPQ158EB 32461 1NPQ 218 EB NPQ218EB 32464 1NPQ 236 EB NPQ236EB 32467 1NPQ 258 EB NPQ258EB 32470 1

MAR/P 118 EB MARP118EB 30242 1MAR/P 136 EB MARP136EB 30243 1MAR/P 158 EB MARP158EB 30245 1MAR/P 218 EB MARP218EB 30248 1MAR/P 236 EB MARP236EB 30249 1MAR/P 258 EB MARP258EB 30253 1

EB - Fittings with electronic ballast ( cos j 0.97), without lamp.

Version Order Product PackCode Code Qty.

NPW/X 236 H DA NPWX236HDA 32406 4NPW/X 258 H DA NPWX258HDA 32407 4

NPP 236 H DA NPP236HDA 32444 1NPP 258 H DA NPP258HDA 32445 1

NPQ 236 H DA NPQ236HDA 32473 1NPQ 258 H DA NPQ258HDA 32474 1

MAR/P 236 H DA MARP236HDA 32500 1MAR/P 258 H DA MARP258HDA 32501 1

MAC 236 H DA MAC236HDA 32495 1MAC 258 H DA MAC258HDA 32499 1

DA - Fittings with dual starting terminal, without lamp.

MAR/P 118 H CL2 MARP118HCL2 30294 1MAR/P 136 H CL2 MARP136HCL2 30295 1MAR/P 158 H CL2 MARP158HCL2 30297 1MAR/P 218 H CL2 MARP218HCL2 30298 1MAR/P 236 H CL2 MARP236HCL2 30300 1MAR/P 258 H CL2 MARP258HCL2 30302 1

CL2 - Fittings with double insulation ( ), without lamp.

Version Order Product PackCode Code Qty.

NPW/X 136 H EES NPWX136HEES 30081 4NPW/X 158 H EES NPWX158HEES 7004323 4

NPP 136 H EES NPP136HEES 7004232 1NPP 158 H EES NPP158HEES 7004237 1NPP 258 H EES* NPP258HEES 7004248 1

NPQ 136 H EES NPQ136HEES 32471 1NPQ 158 H EES NPQ158HEES 32472 1NPQ 258 H EES* NPQ258HEES 7004322 1

MAR/P 136 H EES MARP136HEES 30224 1MAR/P 158 H EES MARP158HEES 30227 1MAR/P 218 H EES* MARP218HEES 30237 1MAR/P 236 H EES* MARP236HEES 30239 1MAR/P 258 H EES* MARP258HEES 30240 1

MAC 136 H EES MAC136HEES 32488 1MAC 158 H EES MAC158HEES 32490 1MAC 258 H EES* MAC258HEES 31755 1

MAC 118 EB MAC118EB 32477 1MAC 136 EB MAC136EB 31754 1MAC 158 EB MAC158EB 31728 1MAC 218 EB MAC218EB 32480 1MAC 236 EB MAC236EB 32487 1MAC 258 EB MAC258EB 31756 1

EES - Fittings with electronic emergency service (*one emergency lamp), without lamp.

SPECIAL VERSIONS

GE Lighting 26

GE Lighting 27

IP 65 with protective glass IP 23 open or with wireguard Class:

Standards: CEI 34.21 / EN 60598-1

230V 50Hz

EUROBAY

EB 250S HPS-T 250 E40* 33680 1

EB 400 S HPS-T 400 E40* 33681 1

EB 250 H HG 250 E40* 33672 1

EB 400 H HG 400 E40* 33674 1

EB 250 M MH 250 E40* 33677 1

EB 400 M MH 400 E40* 33678 1

EBR (Reflector) 33686 5

EBV (Protective glass) 33687 5

EBG (Wireguard) 33688 20

*complete with lamp.

Product PackType Lamps Code Qty.

Luminaires for both commercial and industrial interiors with medium and high mountingheight.Suitable for mercury, sodium and metal halide lamps max. 400W.The size is compact with low overall height.Main body: in die-cast aluminium.The suspension hook in stainless steel is slide-adjustable for balancing the fitting.Gearbox: fixed to main body, made of glass reinforced nylon.Supplied with high power factor control gear mounted on a removable gear tray of zinccoated sheet steel.The side entry is sealed by a hinged door with neoprane gasket and four screws.Wiring entry: through nylon cable-gland PG 13.5 incorporated in the wiring box.Optics: parabolic reflector of anodized aluminium 99.85, facetted, with very high lightoutput, optimized for clear lamps. The reflector is fixed to main body with four bolts and canbe supplied with protective glass and/or wireguard.Lampholder: porcelain E40, skirted, adjustable in four positions to obtain the best lightdistribution according to the type of installation.OPTIONAL ATTACHMENTSProtective glass: tempered, fixed to the reflector by three stainless steel toggles; it isequipped with an auxiliary safety chain to be fixed to the main body.Wireguard: in zinc plated wire, fixed to the main body with a safety chain.

GE Lighting 28

GE Lighting 29

COMMERCIAL LIGHTING

MULTILITE System 8000 is an extremely compact single and twin lamp lightingsystem, specially created to facilitate the design of modern interior lightingschemes.Made of aluminium, modules and joints all have the same section, bringingcontinuity to the entire installation.The modular design of the system and wide variety of light sources available offeran ifinite variety of application solutions that are ideal for meeting the varieddemands of offices, banks, shops, libraries, etc.

40

120

WHITE: (code WH)RED: RAL 3000 (code RD)BLACK: RAL 9005 (code BK)GREY: (code GY)

MULTILITE System 8000

GE Lighting 30

8002 218 WH 1100 2.80 8002218WH 7001708 1

8002 218 RD 1100 2.80 8002218RD 7001714 1

8002 218 BK 1100 2.80 8002218BK 7001717 1

8002 218 GYN 1100 2.80 8002218GYN 32644 1

8002 236 WH 1650 3.50 8002236WH 7001722 1

8002 236 RD 1650 3.50 8002236RD 7001741 1

8002 236 BK 1650 3.50 8002236BK 7001744 1

8002 236 GYN 1650 3.50 8002236GYN 32645 1

8002 258 WH 2200 6.00 8002258WH 7001750 1

8002 258 RD 2200 6.00 8002258RD 7001780 1

8002 258 BK 2200 6.00 8002258BK 7001782 1

8002 258 GYN 2200 6.00 8002258GYN 32650 1

IP 20 Class: I 220V 50HZ IP 40 with

diffuserCat. No. 8151

Length Weight Order Product PackType (mm) (Kg) Code Code Qty.

Cat. No. 8001 Wired module with power factor correction for one T8 fluorescent lamp (not included).

IP 20 Class: I 220V 50HZ IP 40 withdiffuserCat. No. 8151 Cat. No. 8002

Wired module with power factor correction for two T8 fluorescent lamps (not included).

8005 218 WH 550 1.50 8005218WH 7001808 1

8005 218 RD 550 1.50 8005218RD 7001810 1

8005 218 BK 550 1.50 8005218BK 7001812 1

8005 218 GYN 550 1.50 8005218GYN 32652 1

8005 236 WH 1100 2.50 8005236WH 7001815 1

8005 236 RD 1100 2.50 8005236RD 7001818 1

8005 236 BK 1100 2.50 8005236BK 7001820 1

8005 236 GYN 1100 2.50 8005236GYN 32654 1

IP 20 Class: I 220V 50HZ IP 40 withdiffuserCat. No. 8151

Cat. No. 8005 Wired module with power factor correction for two compact fluorescent lamps (not included).

WH = white RD = red BK = black GYN = grey

8010 WH 550 1.10 8010WH 7001825 1

8010 RD 550 1.10 8010RD 7001827 1

8010 BK 550 1.10 8010BK 7001828 1

8010 GYN 550 1.10 8010GYN 32657 1

IP 20 Class: I 220V 50HZ

Cat. No. 8010 Module for E 27 incandescent lamps (not included).

8001 118 WH 1100 2.20 8001118WH 7001646 1

8001 118 RD 1100 2.20 8001118RD 7001652 1

8001 118 BK 1100 2.20 8001118BK 7001654 1

8001 118 GYN 1100 2.20 8001118GYN 32640 1

8001 136 WH 1650 2.90 8001136WH 7001657 1

8001 136 RD 1650 2.90 8001136RD 7001681 1

8001 136 BK 1650 2.90 8001136BK 7001683 1

8001 136 GYN 1650 2.90 8001136GYN 32641 1

8001 158 WH 2200 4.20 8001158WH 7001688 1

8001 158 RD 2200 4.20 8001158RD 7001702 1

8001 158 BK 2200 4.20 8001158BK 7001704 1

8001 158 GYN 2200 4.20 8001158GYN 32643 1

40

120

40

120

40

120

40

120


GE Lighting 31



Length Weight Order Product PackType (mm) (Kg) Code Code Qty

Cat. No. 8015 Module for fixed 50 mm dichroic mirror 12V halogen lamps (not included),complete with die-cast aluminium ring nuts and 200W 220V electronic transformer.

Class: I 220V 50HZ


8030 118 WH 1100 3.30 8030118WH 7001850 1

8030 118 RD 1100 3.30 8030118RD 7001851 1

8030 118 BK 1100 3.30 8030118BK 7001852 1

8030 118 GYN 1100 3.30 8030118GYN 32681 1

8030 136 WH 1650 4.00 8030136WH 7001854 1

8030 136 RD 1650 4.00 8030136RD 7001855 1

8030 136 BK 1650 4.00 8030136BK 7001856 1

8030 136 GYN 1650 4.00 8030136GYN 33066 1

8030 158 WH 2200 4.80 8030158WH 7001858 1

8030 158 RD 2200 4.80 8030158RD 7001859 1

8030 158 BK 2200 4.80 8030158BK 7001860 1

8030 158 GYN 2200 4.80 8030158GYN 33068 1

Cat. No. 8030Emergency lighting module for fluorescent lamp (not included) with EES unit for permanentillumination (duration 1 h).

8015 WH 1100 2.20 8015WH 7001830 1

8015 RD 1100 2.20 8015RD 7001832 1

8015 BK 1100 2.20 8015BK 7001834 1

8015 GYN 1100 2.20 8015GYN 32660 1

IP 20 Class: I 220V 50HZ Cat. No. 8016

Module for swieveling 35 mm dichroic mirror 12V halogen lamps (not included),complete with 200W 220V electronic transformer.

8016 WH 1100 2.20 8016WH 7001836 1

8016 RD 1100 2.20 8016RD 7001838 1

8016 BK 1100 2.20 8016BK 7001840 1

8016 GYN 1100 2.20 8016GYN 32662 1

Cat. No. 8018 Module with 220V electrified track for Guzzini, Erco, Staff, Hoffmeister, Nokia spotlights with adapters (spotlights not included).

8018 WH 1650 3.80 8018WH 7001870 1

8018 RD 1650 3.80 8018RD 7001876 1

8018 BK 1650 3.80 8018BK 7001878 1

8018 GYN 1650 3.80 8018GYN 32667 1

Class: I 220V 50HZ

Cat. No. 8020 Module for 3 JACKLITE series spotlights (not included) complete with 200W 220V electronic transformer.

8020 WH 1100 2.20 8020WH 7001882 1

8020 RD 1100 2.20 8020RD 7001883 1

8020 BK 1100 2.20 8020BK 7001884 1

8020 GYN 1100 2.20 8020GYN 32669 1

Cat. No. 8022Module for R7s linear halogen lamp (not included),complete with protective front cover glass Cat. No. 8166.

8022 WH 550 1.00 8022WH 7001844 1

8022 RD 550 1.00 8022RD 7001846 1

8022 BK 550 1.00 8022BK 7001847 1

8022 GYN 550 1.00 8022GYN 32671 1

IP 20 Class: I 220V 50Hz IP 40 with


40

120

40

120

40

120

40

120

40

120

40

120


GE Lighting 32


Cat. No. 8100Structural compensation module (can be opened for inspection).

8140 WH 550 0.90 8140WH 7002241 1

8140 RD 550 0.90 8140RD 7002242 1

8140 BK 550 0.90 8140BK 7002243 1

8140 GYN 550 0.90 8140GYN 33079 1

Cat. No. 8140Module with 1W/4 OHM loudspeaker.


8141 WH 550 0.80 8141WH 7002245 1

8141 RD 550 0.80 8141RD 7002246 1

8141 BK 550 0.80 8141BK 7002247 1

8141 GYN 550 0.80 8141GYN 33080 1

Cat. No. 8141Module for switches and plugs box.

8100 275 WH 275 0.40 8100275WH 7002218 1

8100 275 RD 275 0.40 8100275RD 7002219 1

8100 275 BK 275 0.40 8100275BK 7002220 1

8100 275 GYN 275 0.40 8100275GYN 33077 1

8100 550 WH 550 0.80 8100550WH 7002223 1

8100 550 RD 550 0.80 8100550RD 7002224 1

8100 550 BK 550 0.80 8100550BK 7002225 1

8100 550 GYN 550 0.80 8100550GYN 33078 1

8100 1100 WH 1100 1.50 81001100WH 7002227 1

8100 1100 RD 1100 1.50 81001100RD 7002228 1

8100 1100 BK 1100 1.50 81001100BK 7002229 1

8100 1100 GYN 1100 1.50 81001100GYN 33070 1

8100 1650 WH 1650 2.20 81001650WH 7002232 1

8100 1650 RD 1650 2.20 81001650RD 7002234 1

8100 1650 BK 1650 2.20 81001650BK 7002235 1

8100 1650 GYN 1650 2.20 81001650GYN 33074 1

8100 2200 WH 2200 3.00 81002200WH 7002237 1

8100 2200 RD 2200 3.00 81002200RD 7002238 1

8100 2200 BK 2200 3.00 81002200BK 7002239 1

8100 2200 GYN 2200 3.00 81002200GYN 33075 1

40

120

40

120

40

120


GE Lighting 33

Cat. No. 8176

Cat. No. 8186

Cat. No. 6169

Cat. No. 8175

Cat. No. 8174

GE Lighting 34


Cat. No. 6169

Cat. No. 8187

Cat. No. 8170

Cat. No. 8171

Cat. No. 8190Cat. No. 8189

Cat. No. 8185

Cat. No. 8172

Cat. No. 8188

Cat. No. 8178

Cat. No. 8173

Cat. No. 8177

Cat. No. 8180

Cat. No. 8184

GE Lighting 35


Order Product PackType For Use with Code Code Qty.

Cat. No. 8149Clip-fit polycarbonate louvre with metal finish.

8153 2 1 x 18 81532 7002266 6/1

8153 4 1 x 36 81534 7002267 6/1

8153 5 1 x 58 81535 7002268 6/1

Cat. No. 8153Clip-fit methacrylate half diffuser for emergency lighting modules.Protection level increase from IP 20 to IP 40.

8149 2 1 - 2 x 18 81492 7002249 12/1

8149 4 1 - 2 x 36 81494 7002250 7/1

8149 5 1 - 2 x 58 81495 7002251 5/1

8149 2L1 2 x 2L 18 81492L1 7002252 15/1

8149 2L2 2 x 2L 36 81492L2 7002253 12/1

Cat. No. 8150Clip-fit opal polycarbonate louvre.

8150 2 1 - 2 x 18 81502 7002255 12/1

8150 4 1 - 2 x 36 81504 7002256 7/1

8150 5 1 - 2 x 58 81505 7002257 5/1

8150 2L1 2 x 2L 18 81502L1 7002258 15/1

8150 2L2 2 x 2L 36 81502L2 7002259 12/1

Cat. No. 8151Click-fit methacrylate diffuser. Protection level increse from IP 20 to IP 40.

8151 2 1 - 2 x 18 81512 7002260 4/1

8151 4 1 - 2 x 36 81514 7002261 4/1

8151 5 1 - 2 x 58 81515 7002262 4/1

8151 2L1 2 x 2L 18 81512L1 7002263 4/1

8151 2L2 2 x 2L 36 81512L2 7002264 4/1

Cat. No. 8152Clip-fit polycarbonate half louvre for emergency lighting modules.

8152 2 1 x 18 81522 7000620 24/1

8152 4 1 x 36 81524 7000621 14/1

8152 5 1 x 58 81525 7002265 10/1

8154 2 1 x 18 81542 7002733 24/1

8154 4 1 x 36 81544 7002734 14/1

8154 5 1 x 58 81545 7002735 10/1

Cat. No. 8154Polycarbonate half louvre with metal finish. Clip-fit to emergency modules.

40

120

40

120

40

120

40

120

40

120

40

120


GE Lighting 36

Order Product PackType For Use with Code Code Qty.

Cat. No. 8160Diffuser for auxiliary signs (without sign message).

8166 8166 7002270 25/1

Cat. No. 8166Cover glass for halogen lamp module Cat. No. 8022, 8300 and 8400.


8170 WH 8170WH 7002271 25/1

8170 RD 8170RD 7002273 25/1

8170 BK 8170BK 7002274 25/1

8170 GYN 8170GYN 33083 25/1

Cat. No. 8170End cap complete with internal connectors.

8171 WH 8171WH 7002277 25/1

8171 RD 8171RD 7002279 25/1

8171 BK 8171BK 7002280 25/1

8171 GYN 8171GYN 33085 25/1

Cat. No. 8171End cap complete with power supply cable clamps and internal connectors.

8172 WH 8172WH 7002282 15/1

8172 RD 8172RD 7002283 15/1

8172 BK 8172BK 7002284 15/1

8172 GYN 8172GYN 33086 15/1

Cat. No. 8172Rotating straight joint complete with internal connectors.

8173 WH 8173WH 7002286 12/1

8173 RD 8173RD 7002288 12/1

8173 BK 8173BK 7002289 12/1

8173 GYN 8173GYN 33088 12/1

Cat. No. 8173Horizontal 90 joint complete with internal connectors.

8160 1 - 2 x 18 8160 7000622 1


Cat. No. 8165Adjustable flaps for Cat. No. 8022, 8300 and 8400. CL18

8165 8165 7002269 25/1

107

120L= 563

40

120

18

40

120

50

18

40

40

360

120

140


GE Lighting 37



Cat. No. 8174T joint complete with internal connectors. CL18

8180 WH 8180WH 7002312 5/1

8180 RD 8180RD 7002313 5/1

8180 BK 8180BK 7002314 5/1

8180 GYN 8180GYN 33427 5/1

Cat. No. 818090 270 adjustable vertical bellows joint complete with end caps and internal connectors.

8174 WH 8174WH 7002292 10/1

8174 RD 8174RD 7002294 10/1

8174 BK 8174BK 7002295 10/1

8174 GYN 8174GYN 33090 10/1

Cat. No. 8175Xjoint complete with internal connectors.

8175 WH 8175WH 7002297 7/1

8175 RD 8175RD 7002299 7/1

8175 BK 8175BK 7002300 7/1

8175 GYN 8175GYN 33092 7/1

Cat. No. 817690 270 adjustable horizontal joint complete with internal connectors.

8176 WH 8176WH 7002303 7/1

8176 RD 8176RD 7002304 7/1

8176 BK 8176BK 7002305 7/1

8176 GYN 8176GYN 33093 7/1

Cat. No. 817790 vertical joint complete with internal connectors.

8177 WH 8177WH 7002308 10/1

8177 RD 8177RD 7002309 10/1

8177 BK 8177BK 7002310 10/1

8177 GYN 8177GYN 33094 10/1

Cat. No. 8178Straight internal connectors (set of 4) for connecting modules.

8178 8178 7002316 50/1

8184 WH 8184WH 7002334 12/1

8184 RD 8184RD 7002335 12/1

8184 BK 8184BK 7002336 12/1

8184 GYN 8184GYN 33437 12/1

Cat. No. 8184Rotating straight joint complete with end caps with internal connectors and wall/ceiling mounting bracket.

160

140

160

160

140

90 270

40

60

40

120

215

40

40

360

120

80

GE Lighting 38



Cat. No. 8185End cap complete with internal connectors and wall/ceiling mounting bracket. CL18

8187 8187 7002329 40/1

Cat. No. 8187Adjustable static ceiling mounting.


8188 8188 7002330 100/1

Cat. No. 8188Equalizer for modules.

8189 WH 8189WH 7002331 10/1

8189 RD 8189RD 7002332 10/1

8189 BK 8189BK 7002333 10/1

Cat. No. 8189Power supply set complete with mounting pin, terminal block, large ceiling rose and 3 x 1,5 mm2 power supply cable, extending to 2 m.

8190 WH 8190WH 7000628 12/1

8190 RD 8190RD 7002346 12/1

8190 BK 8190BK 7000629 12/1

Cat. No. 81903 x 1,5 mm2 power supply cable which can be extended to 2 m.

6169 WH 6169WH 7002357 10/1

6169 RD 6169RD 7002358 10/1

6169 BK 6169BK 7002359 10/1

Cat. No. 6169Straight joint for connecting Systema 6000 to Systema 8000, complete with internal connectors.

8185 WH 8185WH 7002317 12/1

8185 RD 8185RD 7002318 12/1

8185 BK 8185BK 7002319 12/1

8185 GYN 8185GYN 33440 12/1

Cat. No. 8186Ceiling suspension set complete with 2 m steel cable, mounting pin an ceiling rose.

8186 WH 8186WH 7002322 40/1

8186 RD 8186RD 7002327 40/1

8186 BK 8186BK 7002328 40/1

80

32

120

40

360

2000

50

40 30

40 5

2000

75

2000

60

37

40

120

360

GE Lighting 39


All ready-wired modules feature a four-pole terminal block at both ends (or two for the twin-lamp module Cat. No. 8002), suitable for hard wire or flexible cables with a section of up to2.5 mm2.L1 = module power supply through line.L2 = through line for separate switchings only.N = neutral through line.Control gear: 220V 50Hz, heat-resistant 1.5 mm2 cables.

Electrical connection

Straight extruded aluminium modules are connected to one another using accessory Cat. No. 8178 (set of 4: two narrow + two wide links).NARROW LINKS: single lamp profile single lamp profile connectors.WIDE LINKS: single lamp profile twin lamp profile connectors;

for twin lamp profile twin lamp profile connectors.

Mechanical connection

Modules: extruded aluminium with stoved painted finish in four standard colours.End cap and joints: in die cast aluminium complete with internal connectors, with stovedpainted finish in four standard colours.Internal reflectors: in 99.99% pure pre-anodised aluminium with mirror finish.Diffusers: in methacrylate with prismatic internal reeding.Louvre: in polycarbonate.Compliance with standards: CEI 34.21 - EN 60598-1.Protection level: IP 20 IP 40.

*

* Modules Cat. No. 8001, 8002, 8010, 8022.

Specifications


GE Lighting 40

WH = white RD = red BK = black

FREE-STANDING UPLIGHT Cat. No. 8300Free-standing uplight luminaires for halogen lamps (max. 300W) complete with protectivefront cover glass Cat. No. 8166 and dimmer.Body: extruded aluminium body with cast iron base, both with a stoved painted finish.Accessories: adjustable flaps Cat. No. 8165.

WALL-MOUNTED UPLIGHT Cat. No. 8400Wall-mounted uplight for linear halogen lamp (included) (max. 300W) complete withprotective front cover glass Cat. No. 8166.Body: extruded aluminium body with stoved paint finish..Accessories: adjustable flaps Cat. No. 8165.

IP 20 Standards: CEI 34.21 / EN 60598-1

IP 20 Standards: CEI 34.21 / EN 60598-1

Weight Order Product PacType (Kg) Code Code Qty.

8300 WH 7.00 8300WH 7000181 1

8300 RD 7.00 8300RD 7000183 1

8300 BK 7.00 8300BK 7000184 1

8400 WH 0.60 8400WH 7001862 1

8400 RD 0.60 8400RD 7001863 1

8400 BK 0.60 8400BK 7001864 1

1900

50

40

250 120

Free-Standing Wall-Mounted Uplight

GE Lighting 41

MULTILITE System 6000 is an extremely cost-effective single lamp ( 60 mm)lighting system specially made to facilitate the design of modern lightingschemes.Manufactured of aluminium, modules and joints of the same section, bringingcontinuity to the entire installation.The modular design of the system and wide variety of light sources availablemake it possible to create an infinite variety of application solutions that are idealfor meeting the varied demands of offices, banks, shops, libraries, etc.

60

WHITE: RAL 001 (code WH)RED: RAL 3000 (code RD)BLACK: RAL 9005 (code BK)

GE Lighting 42






Cat. No. 6001 Wired module with power factor correction for one T8 fluorescent lamp (not included).

6001 118 WH 1200 1.50 6001118WH 7000186 1

6001 118 RD 1200 1.50 6001118RD 7000187 1

6001 118 BK 1200 1.50 6001118BK 7000188 1

6001 136 WH 1800 2.00 6001136WH 7001886 1

6001 136 RD 1800 2.00 6001136RD 7001888 1

6001 136 BK 1800 2.00 6001136BK 7001889 1

6001 158 WH 2100 3.00 6001158WH 7001891 1

6001 158 RD 2100 3.00 6001158RD 7001892 1

6001 158 BK 2100 3.00 6001158BK 7001893 1


diffuserCat. No. 6151 Cat. No. 6005

Wired module with power factor correction for one compact fluorescent lamp (not included).

6005 136 WH 900 1.20 6005136WH 7001894 1

6005 136 RD 900 1.20 6005136RD 7001895 1

6005 136 BK 900 1.20 6005136BK 7001896 1


Cat. No. 6010 Module for three E27 incandescent lamps (not included).

6010 WH 600 1.00 6010WH 7000194 1

6010 RD 600 1.00 6010RD 7000195 1

6010 BK 600 1.00 6010BK 7000196 1


Cat. No. 6015Module for 12V halogen lamps (not included) with GY 6.35 caps complete with 200W 220V electronictransformer.

6015 150 WH 300 0.60 6015150WH 7000197 1

6015 150 RD 300 0.60 6015150RD 7000198 1

6015 150 BK 300 0.60 6015150BK 7000199 1

6015 350 WH 1200 1.30 6015350WH 7000200 1

6015 350 RD 1200 1.30 6015350RD 7000201 1

6015 350 BK 1200 1.30 6015350BK 7000202 1

Class: I 220V 50HZ

Cat. No. 6018Module of 220V electrified track for Guzzini, Erco, Staff, Hoffmeister, Nokia spotlights (not included)with adapters.

6018 WH 1500 2.60 6018WH 7000216 1

6018 RD 1500 2.60 6018RD 7000217 1

6018 BK 1500 2.60 6018BK 7000218 1

Class: I 220V 50HZ

Cat. No. 6020Module for 3 JACKLITE series spotlights (not included) complete with 200W 220V electronic transformer.

6020 WH 900 1.00 6020WH 7001897 1

6020 RD 900 1.00 6020RD 7001898 1

6020 BK 900 1.00 6020BK 7000221 1

60

60

60

60

60

60

GE Lighting 43



6022 WH 300 0.50 6022WH 7000203 1

6022 RD 300 0.50 6022RD 7000204 1

6022 BK 300 0.50 6022BK 7000205 1


Cat. No. 6022Module for linear halogen lamp (not included) with R7s cap,complete with protective front glass Cat. No. 6166


6030 118 WH 1500 2.20 6030118WH 7000206 1

6030 118 RD 1500 2.20 6030118RD 7000207 1

6030 118 BK 1500 2.20 6030118BK 7000208 1



Cat. No. 6030Emergency lighting module for fluorescent lamp (not included) with EES unit for permanentillumination (duration 1 h).

6100 300 WH 300 0.40 6100300WH 7000634 1

6100 300 RD 300 0.40 6100300RD 7000635 1

6100 300 BK 300 0.40 6100300BK 7000636 1

6100 600 WH 600 0.70 6100600WH 7000637 1

6100 600 RD 600 0.70 6100600RD 7000638 1

6100 600 BK 600 0.70 6100600BK 7000639 1

6100 1200 WH 1200 1.20 61001200WH 7000640 1

6100 1200 RD 1200 1.20 61001200RD 7000641 1

6100 1200 BK 1200 1.20 61001200BK 7000642 1

6100 1800 WH 1800 1.70 61001800WH 7000643 1

6100 1800 RD 1800 1.70 61001800RD 7000644 1

6100 1800 BK 1800 1.70 61001800BK 7000645 1

6100 2100 WH 2100 2.00 61002100WH 7000646 1

6100 2100 RD 2100 2.00 61002100RD 7000648 1

6100 2100 BK 2100 2.00 61002100BK 7000649 1

Cat. No. 6100Structural compensation module (can be opened for inspection) complete with reduction rings for ends.

6101 6101 7000657 1

Cat. No. 6101Reduction ring for ends (necessary when cutting structural modules).

Cat. No. 6140 Module with 1W/4 OHM loudspeaker.

6140 WH 300 1.20 6140WH 7000650 1

6140 RD 300 1.20 6140RD 7000651 1

6140 BK 300 1.20 6140BK 7000652 1

Cat. No. 6141Module complete with two plugs and two switches.

6141 WH 300 0.50 6141WH 7002746 1

6141 RD 300 0.50 6141RD 7000653 1

6141 BK 300 0.50 6141BK 7000654 1

60

60

60

60

60

60


GE Lighting 44


GE Lighting 45

Cat. No. 6176

Cat. No. 8186

Cat. No. 6169

Cat. No. 6175

Cat. No. 6174

GE Lighting 46


GE Lighting 47


Cat. No. 6169

Cat. No. 6187 Cat. No. 6170

Cat. No. 6171

Cat. No. 6183

Cat. No. 8190Cat. No. 8189

Cat. No. 6184

Cat. No. 6173

Cat. No. 6172

Cat. No. 6178


Order Product PackType With Luminaire Code Code Qty.

Cat. No. 6149Clip-fit metallized polycarbonate louvre.

6149 2 1 x 18 61492 7002347 24/1

6149 4 1 x 36 61494 7002348 12/1

6149 5 1 x 58 61495 7002349 10/1

6149 2L1 1 x 2L36 61492L1 7002350 24/1

Cat. No. 6150Clip-fit opal polycarbonate louvre.

6150 2 1 x 18 61502 7002351 24/1

6150 4 1 x 36 61504 7002352 12/1

6150 5 1 x 58 61505 7002353 10/1

6150 2L1 1 x 2L36 61502L1 7000655 24/1

Cat. No. 6151Clip-fit methacrylate diffuser. Increases protection level from IP 20 to IP 40.

6151 2 1 x 18 61512 7002354 8/1

6151 4 1 x 36 61514 7002355 8/1

6151 5 1 x 58 61515 7000656 8/1

6151 2L1 1 x 2L36 61512L1 7002356 8/1

6169 WH 6169WH 7002357 10/1

6169 RD 6169RD 7002358 10/1

6169 BK 6169BK 7002359 10/1


Cat. No. 6169Straight joint for connecting System 6000 to System 8000, complete with internal connectors.

6170 WH 6170WH 7002360 25/1

6170 RD 6170RD 7002361 25/1

6170 BK 6170BK 7002362 25/1

Cat. No. 6170End cap.

6171 WH 6171WH 7002363 25/1

6171 RD 6171RD 7002364 25/1

6171 BK 6171BK 7002365 25/1

Cat. No. 6171End cap complete with power supply cable clamp.

6172 WH 6172WH 7002366 15/1

6172 RD 6172RD 7002367 15/1

6172 BK 6172BK 7002368 15/1

Cat. No. 6172Rotating straight joint.

60

60

60

60

37

40

120

360

60 17

60

70

17

60

70

36


GE Lighting 48



6173 WH 6173WH 7002369 10/1

6173 RD 6173RD 7002370 10/1

6173 BK 6173BK 7002371 10/1

Cat. No. 6173Horizontal/vertical 90 joint.

6174 WH 6174WH 7002372 6/1

6174 RD 6174RD 7002373 6/1

6174 BK 6174BK 7002374 6/1

Cat. No. 6174Horizontal/vertical T joint.

6175 WH 6175WH 7002375 5/1

6175 RD 6175RD 7002376 5/1

6175 BK 6175BK 7002377 5/1

Cat. No. 6175Horizontal/vertical X joint.

6176 WH 6176WH 7002378 10/1

6176 RD 6176RD 7002379 10/1

6176 BK 6176BK 7002380 10/1

Cat. No. 617690270 adjustable horizontal/vertical joint.

6178 6178 7002381 30/1

Cat. No. 6178Internal straight joint for connecting modules.

6183 6183 7002382 60/1

Cat. No. 6183Mid-suspension bracket (excluding cable).

6184 6184 7002383 50/1

Cat. No. 6184Wall-mounting bracket.

60

80

60

80

100

60

100

100

60

90270

80

80

4260

50

60

100

30


GE Lighting 49



8186 WH 8186WH 7002322 40/1

8186 RD 8186RD 7002327 40/1

8186 BK 8186BK 7002328 40/1

Cat. No. 8186Ceiling suspension set complete with 2 m steel cable, mounting pin and ceiling rose.

6187 6187 7002384 40/1

Cat. No. 6187Static ceiling mounting spacer.

8189 WH 8189WH 7002331 10/1

8189 RD 8189RD 7002332 10/1

8189 BK 8189BK 7002333 10/1

Cat. No. 8189Power supply set complete with mounting pin, terminal block, large ceiling rose and 3 x 1.5 mm2

power supply cable extendible to 2 m.

8190 WH 8190WH 7000628 12/1

8190 RD 8190RD 7002346 12/1

8190 BK 8190BK 7000629 12/1

Cat. No. 81903 x 1,5 mm2 power supply cable extendible to 2 m.

2000

50

50 30

2000

75

2000

GE Lighting 50


Ends of all ready-wired modules are fitted with four pole terminal blocks, suitable for hardwires and flexible cables with a section of up to 2.5 mm2.L1 = module power supply through line.L2 = through line for separate switchings only.N = neutral through line.Control gear: 220V 50Hz, heat-resistant cables with section of 1.5 mm2.


Straight extruded aluminium modules are inter-connected mechanically by accessoryCat. No. 6178.


Modules: extruded aluminium with stoved paint finish in three standard colours.End caps and joints: die cast aluminium with internal connectors; stoved paint finish inthree standard colours.Internal reflectors: mirror-finish pre-anodised 99.99% pure aluminium.Diffusers: methacrylate diffuser with prismatic internal reeding.Louvre: polycarbonate.Compliance with standards: CEI 34.21 EN 60598-1.Protection level: IP 20 IP 40.

*

* Modules Cat. No. 6001.

Specifications

GE Lighting 51


MULTILITE System 3000 has been specially designed for innovative lightingsolutions; unlike conventional systems, it is able to form continuous installationswithout a break between one fluorescent lamp and the next, as well as offeringthe possibility of combining direct and indirect lighting in the same module.Manufactured entirely of aluminium, the modular design and wide choice of lightsources available with System 3000 make it possible to create an infinite varietyof application solutions, perfect for offices, banks and shops, etc.End caps, joints and suspension fittings are the same as those used in System6000.All 3 MULTILITE systems 3000, 6000 and 8000 can be combined in a singleinstallation.

100

120

BLACK: RAL 9005 (code BK)


GE Lighting 52

BK = black



Length Order Product PackType (mm) Code Code Qty.

Cat. No. 3001 Wired module with power factor correction for direct lighting with one T8 fluorescent lamp(not included).

3001 118 BK 610 3001118BK 7000222 1

3001 136 BK 1220 3001136BK 7000223 1

3001 158 BK 1520 3001158BK 7001899 1


diffuserCat. No. 3151 Cat. No. 3002

Wired module with power factor correction for direct lighting with two T8 fluorescent lamps(not included).

3002 218 BK 610 3002218BK 7000224 1

3002 236 BK 1220 3002236BK 7000225 1

3002 258 BK 1520 3002258BK 7003492 1



Cat. No. 3003 Wired module with power factor correction for direct and indirect lighting with two T8fluorescent lamps and one 24W lamp. (Lamps not included.)

3003 236 BK 1220 3003236BK 7003493 1

3003 258 BK 1520 3003258BK 7003494 1


Cat. No. 3004 Wired module with power factor correction and louvre for one 34W compact fluorescent lamp(not included).

3004 134 BK 1220 3004134BK 7003495 1


Cat. No. 3020Module for 3 JACKLITE series spotlights (not included) complete with 200W 220V electronictransformer.

3020 BK 1220 3020BK 7003496 1


Cat. No. 3023Module for 70W MQI-TD metal halide lamp (not included) with R7s caps, complete withprotective front cover glass.

3023 BK 920 3023BK 7003497 1



Cat. No. 3030Wired module with power factor correction for two fluorescent lamps (not included),complete with EES on one lamp for permanent lighting (duration 1 h).

3030 236 BK 1220 3030236BK 7003498 1

100

120

100

120

100

120

100

120

100

120

100

120

100

120


GE Lighting 53

BK = black

Length Order Product PackType (mm) Code Code Qty.

Cat. No. 3100Structural compensation module (can be opened for inspection) complete with reduction piecesfor ends.

3100 300 BK 300 3100300BK 7000658 13100 610 BK 610 3100610BK 7000659 1

Cat. No. 3101Reduction piece for ends (necessary when cutting structural modules).

3101 3101 7002748 1

3149 3149 7000660 20/1

Cat. No. 3149Modular clip-fit polycarbonate louvre L 304 mm with metal finish.Number of louvres per fitting: 1-2 x 18: 2 pcs; 1-2 x 36: 4 pcs; 1-2 x 58: 5 pcs.

3150 3150 7000661 20/1

Cat. No. 3150Modular clip-fit polycarbonate louvre L 304 mm. Number of louvres per fitting: 1-2 x 18: 2 pcs; 1-2 x 36: 4 pcs; 1-2 x 58: 5 pcs.


Cat. No. 3151Clip-fit methacrylate diffuser.Increases protection level from IP 20 to IP 40.

3151 2 1/2 x 18 31512 7002750 4/1

3151 4 1/2 x 36 31514 7002751 4/1

3151 5 1/2 x 58 31515 7002752 4/1

Cat. No. 3169Die-cast end cap for joints.

3169 BK 3169BK 7000662 15/1

Cat. No. 3170Plastic end cap..

3170 BK 3170BK 7000663 30/1

100

120

100

120

100

120

100

120

100

120

18

100

120

3

GE Lighting 54


BK = black


Cat. No. 3178Straight internal joint for connecting modules without breaks.

3178 3178 7000664 40/1

Cat. No. 3180Clip-fit plastic joint-cover fins for use with accessories Cat. No. 6173.

3180 BK 3180BK 7000665 15/1

40 20

All ready-wired modules are fitted with 5-pole terminal blocks at both ends suitable for hardwires or flexible cables with a section of up to 2.5 mm2.L1 = module power supply through line.L2 = through line for separate switchings only.L3 = through line for separate switchings only.N = neutral through line.Control gear: 220V 50Hz, heat-resistant 1.5 mm2 section cable.


Straight extruded aluminium modules are mechanically inter-connected by accessory Cat. No. 3178.The straight modules are mechanically connected to the accessories (curved, T and X joints)by accessory Cat. No. 3169 (joint end cap).NB: Accessories are the same as those in System 6000 (6170 6171 6172 6173 6174 6175 6176 6178 6183 6184 6187) and System 8000 (8186 8189 8190).


Modules: extruded aluminium with stoved paint finish.End caps and joints: die cast aluminium complete with internal connectors with a blackpaint finish. Cat. No. 3170 in plastic.Internal reflectors: 99.99% pure pre-anodised aluminium with mirror-finish. Diffusers: methacrylate with internal longitudinal prismatic reeding.Louvre: polycarbonate.Compliance with standards: CEI 34.21 EN 60598-1.Protection level: IP 20 IP 40.

Specifications

GE Lighting 55


Cat. No. 6176

Cat. No. 8186

Cat. No. 6169

Cat. No. 6175

Cat. No. 6174


GE Lighting 56

Cat. No. 6169

Cat. No. 6187 Cat. No. 6170Cat. No. 3170

Cat. No. 6178

Cat. No. 3169

Cat. No. 6171

Cat. No. 8190Cat. No. 8189

Cat. No. 6184

Cat. No. 3180

Cat. No. 6173

Cat. No. 6172

Cat. No. 3178

Cat. No. 6183


GE Lighting 57

The Series 5000 with /16 optics is ideal for work environments with video display terminals.This type of arrangement is characterised by direct longitudional and transverse luminance 200 cd/m2 for vertical angles over 60 and by BATWING type light distribution. All thisadds up to an excellent standard of homogeneous lighting: no luminous emissions in areasof direct light combined with maximum eye comfort for video terminal operators.

Work areas with video display terminals

0

60

L 200cd/m2

GE Lighting 58

Series 5000

60

75

90

135 150 165 180 165 150 135 120120

105

60

75

90

105

45 30 15 0 15 30 45

WHITE ALUMINIUM LOUVRE Reference /5Louvre with broad symmetrical light distribution, featuring longitudinal reflectorsand straight transverse blades, in aluminium with gloss white painted finish.

60

75

90

135 150 165 180 165 150 135 120120

105

60

75

90

105

45 30 15 0 15 30 45

POLISHED ALUMINIUM LOUVRE Reference /6Louvre with broad symmetrical light distribution, featuring longitudinalreflectors, in aluminium with polished finish (99.85%), satin-finished extrudedaluminium transverse blades.

60

75

90

135 150 165 180 165 150 135 120120

105

60

75

90

105

45 30 15 0 15 30 45

SATIN FINISH ALUMINIUM LOUVRE Reference /12Louvre with broad symmetrical light distribution, featuring parabolic longitudinalreflectors in anodised anti-iridescent satin-finished 99.90% pure aluminium;resistant to finger prints. Satin-finished extruded aluminium transverse blades.

60

75

90

135 150 165 180 165 150 135 120120

105

60

75

90

105

45 30 15 0 15 30 45

MIRROR-FINISH ALUMINIUM LOUVRE Reference /16Louvre with broad symmetrical Batwing light distribution, featuring longitudinalreflectors and double parabolic transverse blades, in anodised anti-iridescent99.90% pure aluminium with mirror finish. Direct longitudinal and transverseluminance less than 200 cd/m2 for vertical angles over 60.

60

75

90

135 150 165 180 165 150 135 120120

105

60

75

90

105

45 30 15 0 15 30 45

METHACRYLATE DIFFUSER Reference /51Acrylic diffuser with prismatic interior mounted in a white painted frame.

TRASVERSALE

ASSIALE

GE Lighting 59

Series 5000 optical accessories

TRANSVERSE PLANEAXIAL PLANE

IP 40 Class: I

Mark:

Standards: CEI 34.21 / EN 60598-1

230V 50Hz

Series 5500Recessed luminaires for mounting on exposed 24 mm T sections of 600 x 600 mm panelsuspended ceilings.Body: press-bent 6/10 mm sheet steel (=.5/10 mm for 4x36 models) with white powderpaint finish.Optical accessories: see page 59.Control gear and electric circuit: 230V 50Hz; switch start, HT 90C heat-resistant 0.75 mm2 section hard wires, complete with built-in 2A fuse.

5500/218 292 592 622

5500/236 292 1192 1232

5500/318 592 592 622

5500/418 592 592 622

5500/436 592 1192 1232

5500/334 2L 592 592 622

Dimensions (mm)Type A L1 L2

92

L2

L1A

GE Lighting 60

Series 5500

5500/218/5 H 2 x F18 T8 55002185 30096 4.00 1 80

5500/218/6 H 2 x F18 T8 55002186 31540 4.00 1 80

5500/218/12 H 2 x F18 T8 550021812 31435 4.00 1 80

5500/218/16 H 2 x F18 T8 550021816 31437 4.00 1 80

5500/218/51 H 2 x F18 T8 550021851 31438 4.00 1 80

5500/236/5 H 2 x F36 T8 55002365 31442 6.50 1 40

5500/236/6 H 2 x F36 T8 55002366 30106 6.50 1 40

5500/236/12 H 2 x F36 T8 550023612 31439 6.50 1 40

5500/236/16 H 2 x F36 T8 550023616 31440 6.50 1 40

5500/236/51 H 2 x F36 T8 550023651 31441 6.50 1 40

5500/318/5 H 3 x F18 T8 55003185 30111 5.00 1 42

5500/318/6 H 3 x F18 T8 55003186 30113 5.00 1 42

5500/318/12 H 3 x F18 T8 550031812 31445 5.00 1 42

5500/318/16 H 3 x F18 T8 550031816 31447 5.00 1 42

5500/318/51 H 3 x F18 T8 550031851 31547 5.00 1 42

5500/418/5 H 4 x F18 T8 55004185 31461 5.50 1 42

5500/418/6 H 4 x F18 T8 55004186 31463 5.50 1 42

5500/418/12 H 4 x F18 T8 550041812 31452 5.50 1 42

5500/418/16 H 4 x F18 T8 550041

Date post:	18-Oct-2015
Category:	Documents
Upload:	dejanoskia
View:	211 times
Download:	3 times

GE Lighting Sviestuvai

Documents