BEDO ® reserves the right to change materials or modify the design of its product without notification as part of the company’s continuing product improvement program www.bedoeg.com Digital Multi-Meter Electricity, Electronics and Digital Circuits Interactive Lab General Features Main Interface Unit Model No: BIU-1100 • Input: 1-phase, 220 VAC, 50 Hz. • Adjustable DC voltage (0 - 10 V). • Memory for measurements storage. • DC Fixed Output voltages (+5V, + 15V, -15V). • Includes a comprehensive collection of sockets for external connection. • Compatible with mat-lab and lab-view. • Complete with Built in power supply. • Built in digital function generator. • Built in 2-channel oscilloscope. • Built in multi-meter. • Relay outputs. • USB interface to connect with PC. • The unit comes in a metal rugged design. • Locking mechanism insures fixation of experimentation cards to the base unit. • The unit is protected against electromagneti disturbance and noise. BIL 1100 • This laboratory package features a desktop,handheld, self-contained, accessible laboratory introduces the ba- sics of power electronics, electricity and digital circuits to the trainees via a PC-connected training system. • The system composition is made up of hardware and software, it consists of main interface unit that rep- resents the hardware, and different cards that cover different specialties which represents the software and can be plugged in using a group of connection leads and plugs integrated with the unit. • The base unit has many functionalities incorporated with it for signal generation and analysis such as digital function generator, oscilloscope, multi-meter, a built-in data acquisition system so it can be connected to a PC via USB for experimenting an interactive learning through dedicated software. Each plug-in card, incorporates certain features or functionalities to be experimented by students according to its area of study. • 3¾-digit display with resolution: ±4 000 Digits • Measuring ranges: * Voltage: 400mV–1000V AC/DC, * Current: 400µA–10A AC/DC * Resistance: 30ohm-30Mohm * Capacitance: 4nF to 200µF * Frequency: up to 100kHz • Diode test continuity test. • Automatic range selection. • Data hold / Max – Min memory. • Measuring leads, Protective sleeve, and battery are provided. • Signal Sampling (100MSample) • Analogue Signal input with overcurrent Protection • Analogue Signal output. • Digital input • Digital output
Transcript
BEDO ® reserves the right to change materials or modify the design of its product without notification as part of the company’s continuing product improvement program www.bedoeg.com
Digital Multi-Meter
Electricity, Electronics and Digital Circuits Interactive Lab
General Features
Main Interface Unit Model No: BIU-1100
• Input: 1-phase, 220 VAC, 50 Hz.• Adjustable DC voltage (0 - 10 V).• Memory for measurements storage.• DC Fixed Output voltages (+5V, + 15V, -15V).• Includes a comprehensive collection of sockets for
external connection.• Compatible with mat-lab and lab-view.• Complete with Built in power supply.• Built in digital function generator.• Built in 2-channel oscilloscope.• Built in multi-meter.• Relay outputs.• USB interface to connect with PC.• The unit comes in a metal rugged design.• Locking mechanism insures fixation of experimentation
cards to the base unit.• The unit is protected against electromagneti
disturbance and noise.
BIL1100
• This laboratory package features a desktop,handheld, self-contained, accessible laboratory introduces the ba-sics of power electronics, electricity and digital circuits to the trainees via a PC-connected training system.
• The system composition is made up of hardware and software, it consists of main interface unit that rep-resents the hardware, and different cards that cover different specialties which represents the software and can be plugged in using a group of connection leads and plugs integrated with the unit.
• The base unit has many functionalities incorporated with it for signal generation and analysis such as digital function generator, oscilloscope, multi-meter, a built-in data acquisition system so it can be connected to a PC via USB for experimenting an interactive learning through dedicated software. Each plug-in card, incorporates certain features or functionalities to be experimented by students according to its area of study.
• 3¾-digit display with resolution: ±4 000 Digits• Measuring ranges:
* Voltage: 400mV–1000V AC/DC, * Current: 400µA–10A AC/DC* Resistance: 30ohm-30Mohm* Capacitance: 4nF to 200µF* Frequency: up to 100kHz
• Diode test continuity test.• Automatic range selection. • Data hold / Max – Min memory.• Measuring leads, Protective sleeve, and battery
are provided.
• Signal Sampling (100MSample) • Analogue Signal input with overcurrent Protection • Analogue Signal output.• Digital input • Digital output
BEDO ® reserves the right to change materials or modify the design of its product without notification as part of the company’s continuing product improvement program www.bedoeg.com
• The interactive software works as an interface between the student and the main interface unit to provide a better understanding and a complete grasp of theories, principles, different setups and ideal procedures to conduct the experiments properly.
• The software features virtual measuring instruments, monitoring of power supplies, signal generators to perform the experiments accurately.
• The software is provided with a class management program that allows for profiles creation for both students and teachers via different dashboards.
• The interactive multimedia is able to submit a detailed report about the student attendance, performance, progress and final grade.
• The software is capable of testing the trainees troubleshooting capabilities and evaluate their perfor-mances.
• The software provides a complete monitoring controlling and data storing for the whole system.
• Guidelines for teachers are available with the software contents in both Arabic & English languages with all necessary helping pictures, graphs, charts and vide-os.
• Virtual instruments include: Multi-channel oscilloscope including all the necessary
functionality for conducting all the set of experiments, like:
• Multi-meter • Function generator• Digital inputs/outputs • Management of the power supply• DB meter• Bode plotter• Network control centre• Network configuration
Multimedia Courses With Virtual InstrumentsModel No. : SB-1100
Scope of Delivery
• Main Interface Unit • Digital Multi-Meter • Power Cord • Connecting leads and plugs• USB cable • User Manual • CD Software
BEDO ® reserves the right to change materials or modify the design of its product without notification as part of the company’s continuing product improvement program www.bedoeg.com
DC Course Card
Model No. : BE-1101
AC & Three-Phase Course Card
Model No. : BE-1102
• Studying the operation of simple circuits• Assembling circuits according to the circuit diagrams. • Learn how to use ammeters and voltmeters thus
measuring voltage and amperage in circuits • Investigate the influence of the measuring instrument
itself • Investigate the effect of where the measurement is
made on the value measured • Assemble voltage divider circuits & Learn how to
measure resistance and voltage on voltage dividers • Calculate no-load voltage division values.• Investigating an incandescent lamp’s characteristic by
assembling its circuit.• Determine the relationship between temperature and
resistance • Demonstrate an incandescent lamp’s resistance
properties• Assemble circuits for measuring, identifying and
displaying a VDR’s characteristic• Demonstrate the behaviour of resistors with a
negative temperature coefficient• Determine different applications for NTC resistors• Investigate relay principle of operation by assembling
a simple relay circuit • Make a comparison between a relay’s functions and
digital techniques.• Learn how to charge and discharge a capacitor & how
to measure the charge and discharge currents
• Differentiate between direct and alternating current / voltage & learn how alternating current is generated.
• Identify the relationship between alternating voltage, current and power.
• Calculations associated with alternating variables • Identify alternating current characteristics &
advantages.• Learn about Ohm’s law in an AC circuit• Determine the capacitance of a capacitor &
Investigate its charging and discharging.• Determine the reactance of a capacitor.• Investigate connection of capacitors connected in
series and parallel. • Investigating the behaviour of a capacitor supplied
with a variable voltage.• Learn about phase angle & low-pass filter.• Identify the inductance of a coil and studying its
different way of connections & series and parallel con-nections of R, L and C
• Investigate transformer operation under load and no-load
• Demonstrate how three-phase current is generated. • Identifying & measuring the voltages of a three-phase
system • Identifying and determining the relationships between
the voltages in addition to the phase-shift angles between voltages.
• Investigating star & delta connection under balanced/unbalanced load.
Scope of Delivery
• Experimental Card• Connecting leads and plugs • CD Software
Scope of Delivery
• Experimental Card• Connecting leads and plugs • CD Software
BEDO ® reserves the right to change materials or modify the design of its product without notification as part of the company’s continuing product improvement program www.bedoeg.com
Semiconductors Course Card
Model No. : BE-1103
Basic Electronic Circuits Course Card
Model No. : BE-1104
• Definition of semiconductors science• Introduce diodes in DC and AC circuits, half-wave rec-
tifiers, bridge rectifiers, Zener diodes to the trainees.• Introducing light emitting diodes• Identifying smoothing and residual ripple • Investigating basic functionality of bipolar transistors • Controlling current measuring, identifying input and
output characteristics of bipolar transistors• Identifying of basic functioning principle of an FET • Investigating phase control using diacs or triacs• Identifying JFETs and MOSFETs characteristic • Introducing thyristor principle of operation & Learn
how to use it as a switch.
• Investigate amplifier circuits with bipolar transistors & Identify differences and similarities with bipolar transistors.
• Investigate field effect transistors in common source/ drain circuits
• Studying of a two-stage amplifier with capacitive coupling & coupling of transistor stages by means of RC circuits.
• Studying multiplication of the gain from a sequence of amplifier stages.
• Investigating Saw-tooth generators (pulse generators)• Studying Sine-wave generator using an LC circuit• Investigating amplitude modulators and demodulators• Studying frequency modulation, voltage multipliers &
stabilizing circuits.• Studying of conversion of a pulsed voltage into DC ,
DC converters phase control using a thyristor/TRIAC & operational amplifiers
• Investigating full-wave control using zero-voltage switching
Scope of Delivery • Experimental Card• Connecting leads and plugs • CD Software
Scope of Delivery
• Experimental Card• Connecting leads and plugs • CD Software
BEDO ® reserves the right to change materials or modify the design of its product without notification as part of the company’s continuing product improvement program www.bedoeg.com
Optoelectronics Course Card
Model No. : BE-1105
Digital Technology Course Card
Model No. : BE-1106
• Investigating LED parameters and characteristics & Infra-red LED.
• Investigating photovoltaic open-circuit voltage.• Investigating photovoltaic element switching
properties.• Studying photodiode and Phototransistor
character is t ic & swi tch ing proper t ies of a p h o t o t r a n sistor.
• Investigating signal transmission in free space• Invest igat ing s ignal t ransmission with f iber
• Studying of Half adder / Full adder• Studying of Number Systems• Investigating 4-bit numbers• Studying of subtraction circuits & code conversion• Studying of RS flip-flop• Studying of static and dynamic D flip-flops• Studying of JK flip-flops & JK master-slave flip-flops• Investigating applications of flip-flops
Scope of Delivery
• Experimental Card• Connecting leads and plugs • CD Software
Scope of Delivery
• Experimental Card• Connecting leads and plugs • CD Software
BEDO ® reserves the right to change materials or modify the design of its product without notification as part of the company’s continuing product improvement program www.bedoeg.com
Sequential circuits course card
Model No. : BE-1107
• Investigating 7-segment display. • Studying of Asynchronous 4-bit binary up / down/
