Contact Diesel and Marine Group, Wherwell Priory, Wherwell, Hampshire, SP11 7JH, UK t: +44 (0)1264 860 186 f: +44 (0)1264 860 180 [email protected] www.dieselmarinegroup.com
GENERAL OVERVIEW
The Diesel and Marine Group supports the power generation, marine, offshore, chemical, water and railway industries. Exporting to more than 100 countries around the world, we’re a dynamic, growing and independent group of companies incorporating Simplex-Turbulo, Dorman Diesels and Lincoln Diesels.
Diesel engine service and spares• Allen• Bergen• Dorman• Himsen• MaK• MAN• Mirrlees Blackstone
Marine componentsmarine components• Becker Intelligent Monitoring
Systems (BIMS)• Becker Mewis Duct®
• Becker rudder systems• rudderstock bearings and seals• stabilisers• Turbulo bilge water separators• new propellers and blades
Diesel engine reconditioning and parts exchange
• complete engine overhaul• crankshaft machining and
polishing• connecting rod refurbishment• cylinder liner honing• cylinder head overhaul• piston crack detection and
remachining
• Nohab Polar• Paxman• Perkins 4000• Pielstick• Ruston• Vasa• Wärtsilä
shaft components• sterntube seals• flexitube sterntubes• sterntube bearings• shaft couplings• super grip bolts• thrust bearings• shaft alignment• bulkhead seals• net protection
• fuel injector overhaul• water and oil pump overhaul• intercooler cleaning and
pressure testing• turbocharger reconditioning• Gali air starter overhaul
Guaranteeall major components are guaranteed for 12 months and work carried out is guaranteed for six months
Insurance£5m product liability insurance
Propulsion systems service and repair• controllable pitch propulsion systems
and thrusters• class approved bonding of seals in-situ• supply of oversized blade carriers and
sliding blocks• in situ welding of propellers and blades
Filtration and condition monitoring systemsextensive range of new filters and replacement elements for:• hydraulic oil• lube oil• water• fuel
members of Diesel and Marine Group
an engineer at work on a sterntube linerreconditioning of components
• Durability Coatings to protect against abrasion, cavitation and corrosion
• shaft couplings• sterntube seal liner refurbishment
• test kits for hydraulic oil, lube oil and fuelapplications
• MANN+HUMMEL lube oil centrifuge• condition monitoring equipment for thrusters,
cylinder liners and for vibration• portable hydraulic oil purifiers• exhaust gas monitors (CEM)
Contact Diesel and Marine Group, Wherwell Priory, Wherwell, Hampshire, SP11 7JH, UK t: +44 (0)1264 860 186 f: +44 (0)1264 860 180 [email protected] www.dieselmarinegroup.com
Guaranteeall major components areguaranteed for 12 months
Insurance £5m product liability insurance
S-T Diesel and Marine Group is one of the largestindependent stockists of spare parts for medium-speeddiesel engines. We are agents and/or stockists formany of the leading European diesel engine componentmanufacturers who are also supplying directly to theoriginal engine builders, thereby guaranteeing OEM quality.
We recondition cylinder heads, valve cages and conrods, service exchange contracts are also undertaken.
Engine models for which we can offer full support and service:
• Allen
• Bergen
• Dorman
• Himsen
• MaK 453
• MAN
• Mirrlees Blackstone
• Nohab Polar
• Paxman Y3J
• Perkins 4000
• Pielstick
• Ruston
• Vasa
• Wärtsilä
Components for other engine types are also available.
DIESEL ENGINE SERVICE AND SPARES
• new components• reconditioning of:
- cylinder heads- valve cages- conrods
• service exchange• OEM quality
Components we stock include:• bearings• condition monitoring equipment• cooling water pumps• cylinder head valves, valve guides, valve seats and collets• cylinder liners and ‘O’ ring sets• fuel injection equipment• fuel, lube oil, hydraulic oil and water test equipment• fuel pipes• gas control valves• indicator valves• heat exchangers, charge air coolers and radiators• piston rings• pistons• seal and gasket kits• springs• valve rotators, all types including rotocaps, BSR, Turnomats®
Air startersWe stock the robust Gali range of air starter. These can be installed directly to the 30 bar compressed air system without the need for a pressure reducing valve, thereby ensuring first time starting. We offer:• new starters for engines from 50kW to 12MW• reconditioning and spares kits• conversion kits from other starters
Air coolersWe can supply a wide range of charge air coolers for two- and four-stroke diesel engines to original specifications including premium tin-coated coolers to increase resistance to corrosion, extend lifetime and improve heat transfer.
Contact Diesel and Marine Group, Wherwell Priory, Wherwell, Hampshire, SP11 7JH, UK t: +44 (0)1264 860 186 f: +44 (0)1264 860 180 [email protected] www.dieselmarinegroup.com
DIESEL SERVICE, RECONDITIONING AND PARTS EXCHANGE
Service
S-T Diesel and Marine Group’s experienced service engineersare available to carry out or supervise engine overhauls on aworldwide basis.
Refurbishing major engine components can achieve worthwhilereturns by extending lifespan and increasing operatingefficiency and profitability. The reconditioning process takesplace in well-equipped workshop facilities, each itemundergoes stringent inspection and is carefully tracked andtested. A detailed overhaul report is supplied with each order.We ensure rigid compliance with health and safety guidance andexercise a general duty of care with regard to our environment.
Our reconditioning services includes:
• crankshaft machining andpolishing
• connecting rod refurbishmentand remachining
• cylinder liner honing
• cylinder head completeoverhaul
• valve seat grinding
• viscous vibration dampers
Parts exchange
Where time is critical we offer a service exchange program enabling customers to keep downtime to an absolute minimum.The principle of these schemes is simple: customers are provided with remanufactured and guaranteed components (frequently their own) in exchange for worn components removed during the service. Components which are usually covered under these schemes include cylinder heads, fuel pumps, injectors, water and lube oil pumps and turbochargers.
• piston crack detection andremachining
• fuel injector overhaul
• water and oil pump overhaul
• intercooler cleaning andpressure testing
• turbocharger reconditioning
• complete engine overhaul
Durability coatingsThese tungsten-carbide coatings are specifically formulated to provide protection against abrasion and cavitation. The coating is applied using the high velocity oxygen fuel (HVOF) technique operated under technically prescribed parameters.
Old units are received in our workshops. Their receipt is recorded and the castings marked and documented for reporting and traceability purposes.
Any valves and stud work are removed and the casting inspected for damage using crack detection and pressure testing techniques.
Valve guides and valve seats are removed and the bare head is thoroughly de-carbonised and cleaned.
Valve seat locating pockets are inspected and reworked as necessary, the flame and gasket faces are re-skimmed as required and the replacement seats are cut back to original specifications using the Chris Marine equipment.
With guides fitted, the valves are ‘lapped’ into their respective seats for individual fit and the head is reassembled. The hydraulic pressure test and final inspection are conducted before the head is painted, preserved, if required, and packed to customer specific requirements.
Reclassification is available on request. but all repairs are covered by our own internal report which identifies the work carried out and provides full traceability of your units.
TY
PI
CA
L
WO
RK
F
LO
W
OF
C
YL
IN
DE
R
HE
AD
O
VE
RH
AU
L
Contact Diesel and Marine Group, Wherwell Priory, Wherwell, Hampshire, SP11 7JH, UK t: +44 (0)1264 860 186 f: +44 (0)1264 860 180 [email protected] www.dieselmarinegroup.com
Guarantee all work is guaranteed for six months
Insurance £5m product liability insurance
We offer a comprehensive service from engine to the propeller, including full overhaul of propeller hubs, bow thrusters, shaft couplings and sterntube seals. Our team of experienced engineers is dedicated to the maintenance and repair of a wide range of sterntube seals on a worldwide basis.
Original spares, correct tolerances
Not only is all work carried out fully guaranteed, but, even more importantly, you can be sure that your seals are reassembled with original spares in full accordance with manufacturers’ tolerances.
Computerised records, advice for future docking
At the end of every job a report is given to the customer, listing full details of work carried out and the condition of the seal, together with any recommendations for the future. All reports are added to our database and can be referred to for future planning or maintenance schedules.
Time required to replace seals
Depending upon the circumstances found on site, our engineers will typically require three days to complete standard or straightforward repairs including bonding.
Our engineers liaise closely with superintendents and the shipyard in order to ensure the work is carried out as quickly as possible.
Class approved bonding of seals in situ
It is possible to replace the sealing rings without pulling the shaft by cutting off the old sealing rings and then vulcanising the new sealing rings using a specialist bonding device and a patented two-component adhesive. This bonding procedure is approved by class as a permanent repair.
STERNTUBE SEAL SERVICE AND PROPULSION SYSTEMS
Propulsion systems
Our engineers have many years of experience in the servicing, maintenance and repair of propulsion systems and thrusters including:
• Wärtsilä/Lips range of CPP and thrusters
• Schottel propulsion units (approved service station)
We can machine new components and carry out a control system analysis with full retrofits if required.
Propeller repair
All welding repairs are performed to class approved procedures. Our engineers carry out:
• welding in-situ or in the workshop
• on site balancing
• scanning of blades
• ultrasonic crack detection
• manufacture of replacement blade tips, complete blades and propellers
Mobile balancing and measuring equipment
• mobile balancing and measuring equipment for propeller blades up to a weight of 6.5 tons
• blades are balanced within a tolerance of 2.5kg
• CPP blades can now be measured in any location
We can offer machining and delivery of:
• propeller and thruster hubs and parts
• rudder or tail shafts up to 20 meters
• sterntube seal liners
• propeller blade foot machining
• supply of oversized blade carriers and sliding blocks
• reconditioning of shaft couplings
• delivery of other parts and tools on special request
Filtration systems
We provide a wide range of filtration systems for hydraulic, fuel and lube oil applications. These include high, medium and low pressure filters, return line filters, offline filters, bypass filters, spin-on filters and mobile systems.
Replacement elements
We provide replacement elements suitable for • Boll & Kirch• Donaldson• Internormen• Mahle• MANN-FILTER• Parker• Vokes
MANN+HUMMEL lube oil centrifugesThese products clean oil by generating centrifugal force 2000 times greater than gravity, removing high density, sub-micron particles. This can extend the lifespan of both the main lube oil filter cartridge as well as the lube oil.
The benefits:• easy retrofit• quick and simple to maintain• reduced downtime• reduced engine wear• reduced waste disposal costs• reduced maintenance costs• cleaner oil, extending oil life and increasing efficiency• longer service intervals• quick return on investment
FILTRATION AND CONDITION MONITORING SYSTEMS
Contact Diesel and Marine Group,Wherwell Priory, Wherwell,Hampshire, SP11 7JH, UKt: +44 (0)1264 860 186 f: +44 (0)1264 860 [email protected] www.dieselmarinegroup.com
Particle reduction in the lube oil
Condition monitoring and testing equipment
Parker have an extensive range of easy to use testing and condition monitoring equipment, including:
• FTIR³ oil analyser
• cylinder liner cold corrosion test kits
• lube oil viscometer tester
• condition monitoring equipment for thrusters
• vibration monitoring and analysis equipment
• portable purifier for hydraulic oil
Marine fluids testing equipment
These products offer an efficient and cost-effective method for meeting your various fluid analysis needs. They include:
• fuel drip bunker samplers
• fuel samplers
• bottle samplers
• lube oil BN and water in oil test kits
• flashpoint detectors
• cloudpoint detectors
• viscosity meters
• fuel density meters
• fuel compatibility testers
• purpose built storage for bunker sampler kits
Simplex-Turbulo is a Marine Master Distributor for Parker Kittiwake with responsibility for the
marine and power generation industries. We offer a range of fuel, lube oil and water testing
equipment.