General Threaded Pressure Regulators - Gommer · General Threaded Pressure Regulators ... O-rings...

General Threaded Pressure RegulatorsModel GRT8 1/4″ NPT – ThreadedThe GRT8 regulators are available as springloaded pressure regulatorsThe design pressures are 420 and 700 bar Material is Stainless Steel 316LSeatdiameter 2,5 mm

datasheet GRT8S Springloaded Pressure Regulator

Model GRT15 1/2″ NPT – 1/2” BSPP – ThreadedThe GRT15 regulators are available as springloaded pressure regulatorsThe design pressures are 16,50,280 and 420 bar Material is Stainless Steel 316LSeatdiameter 7 mm – Cv 1.0 and Cv 0.7

datasheet GRT15S-16 Springloaded Pressure Regulatordatasheet GRT15S-50 Springloaded Pressure Regulatordatasheet GRT15S-420 Springloaded Pressure Regulator

Model GRT20 3/4″ NPT – 3/4” BSPP – ThreadedThe GRT20 regulators are available as springloaded and domeloaded pressure regulatorsThe design pressures are 16,50,280 and 420 bar Material is Stainless Steel 316LSeatdiameter 9,5 mm – Cv 1.8

datasheet GRT20S-16 Springloaded Pressure Regulatordatasheet GRT20S Springloaded Pressure Regulator

Model GRT25 1″ NPT – 1” BSPP – ThreadedThe GRT25 regulators are available as springloaded and domeloaded pressure regulatorsThe design pressures are 16,50,280 and 420 bar Material is Stainless Steel 316LSeatdiameter 12,5 mm – Cv 3.2

datasheet GRT25S-16 Springloaded Pressure Regulatordatasheet GRT25S Springloaded Pressure Regulatordatasheet GRT25D Domeloaded Pressure Regulator

Model GRT40 1 1/2″ NPT – 1 1/2” BSPP – ThreadedThe GRT40 regulators are available as springloaded and domeloaded pressure regulatorsThe design pressures are 16,50,280 and 420 bar Material is Stainless Steel 316LSeatdiameter 16,5 mm – Cv 5.5

datasheet GRT40S-16 Springloaded Pressure Regulatordatasheet GRT40S Springloaded Pressure Regulatordatasheet GRT40D Domeloaded Pressure Regulator

Model GRT50 2” BSPP – ThreadedThe GRT50 regulators are available as springloaded and domeloaded pressure regulatorsThe design pressures are 16,50,280 and 420 bar Material is Stainless Steel 316LSeatdiameter 22,5 mm – Cv 10

datasheet GRT50D Domeloaded Pressure Regulator

page 1 / 4 Revision 1611a

www.dutchregulators.com

Springloaded Pressure Regulator Model – GRT8S

Description The GRT8S springloaded pressure regulator reduces the supply pressure on the inletside to a controlled pressure on the outletside.

Specifications Inlet pressure 420 or 700 bar Adjustable 0-700 bar - 6 pressure ranges Connections 1/4" NPT Seatdiameter 2,5 mm Cv / Kv Cv 0.1 / Kv 0.08

Fluids This pressure regulator is suitable for gases and liquids.

Materials The regulator is made out of barstock stainless steel material.

Body ss 316L Springhousing ss 316L Valve ss 316L Seat PCTFE or PEEK Valve spring ss 302 Setspring ss 302 O-rings NBR, FKM or EPDM

Other materials available on request.

All metal parts are marked with a traceable batch number. Material certificates are available on request.

Technical details • all parts cleaned and degreased• leak-tight seat design• all regulators tested before delivery

Standards • EN 12516 - design • EN 12266-1 - testing • PED 2014/68/EU - SEP (article 4, paragraph 3)

• ATEX 94/9/EC - II 2G

158

56 mm

Ø59

17




Options Many options are available. The most requested options are mentioned below. Materials Regulators can be produced in higher graded materials than stainless steel 316L. Seals

Regulators can be equipped with FFKM + PTFE seals. Other compounds for higher or lower temperatures are available. NACE - MR 0175

All wetted parts of the regulators can be supplied according to NACE MR 0175, including Inconel X750 valvespring and a NACE report.

Captured vent

The thread of the knob-spindel is standard not sealed. The spindel is sealed with the captured vent option. Fluids can be piped away to the vent connection.

Spare parts Spare parts kits are available for the regulator. Mention the serial number in case you need spare parts for existing regulators.

Dependency Character of the regulator is “dependency”. The set-pressure will increase, when you have a decreasing inletpressure. Dependency ratios are listed below. • range 0-20 bar - 1:100 • range 0-40 bar - 1:100 • range 0-100 bar - 1:40 • range 0-280 bar - 1:14 • range 0-420 bar - 1:10 • range 0-700 bar - 1:6

Flow The regulator has good flow performance over the complete range of pressures. Ask for advice if this regulator is the best choice for your application.

Adjusting the regulator The regulator comes standard with a knob. The threadpiece below the knob is designed for frequent adjustment.

Regulators that have a fixed setpoint, can be equipped with a locking cap.




Internals The internals of the regulator are important for the performance. The different internals are mentioned below.

Piston sensing

Piston sensed for all pressure ranges.

Plastic seated

PCTFE is recommended because it seals easy. PEEK is recommended for liquid applications.

Valvespring

The valvespring gives high spring force to ensure seat-tightness.

Filter The regulator can be supplied with an internal filter element to reduce the chances of seat leakage.

Gaugeports The regulator has standard two 1/4" NPT gaugeports to measure the inlet and outletpressure.

Additional gaugeports not available for model GRT8S.

Gauges Regulators can be supplied with gauges.

Below ranges are available: 0-4 bar / 0-10 bar / 0-25 bar / 0-60 bar / 0-160 bar / 0-400 bar / 0-600 bar

• case diameter 63 mm• internals ss 316• bottom connection 1/4” NPT

Self-venting The self-venting option provides the possibility to relieve the outletpressure when a decreased setpressure is required. See captured vent option for a sealed knob-spindel.

Self-venting cannot be used as safety valve.

Mounting The regulator can be mounted in every position (horizontal / vertical).

The bottom of the regulator has two mounting holes M5 with 5 mm thread and a C-C distance of 22 mm.

Panel mounting Panel mount ring available for mounting in a panel.

Section view

Section view of: GRT8S-420N100-SSKN

Topview




Connections The regulator has threaded connections, designed for compression fittings.

Line connections NPT threads according to ANSI B1.20.1

Vent connection

The body of GRT8S has a 1/8” NPT vent connection. Do not plug the connection.

For self-venting and captured vent, the vent connection can be used to pipe away the fluid.

Design pressures The design pressure applies for inlet and outletside.

Seat materials The seat materials are related to the design pressure ranges.

PCTFE or PEEK design pressure 420 bar PEEK design pressure 700 bar

Temperature The general temperature range of the regulator is -50 / 200 °C, but is often limited due to the used sealing materials.

PCTFE seat - 50 / 60 °C PEEK seat - 50 / 200 °C NBR seals - 35 / 130 °C FKM seals - 20 / 200 °C EPDM seals - 50 / 120 °C

Typenumber explanation

Example : GRT8S - 420N280 - SSKN - S - F

model design pressure connections adjustable material seat seals options

GRT8S 420

700

: 420 bar

: 700 bar

N : 1/4" NPT 20

40

100

280

420

700

: 0-20 bar

: 0-40 bar

: 0-100 bar

: 0-280 bar

: 0-420 bar

: 0-700 bar

SS SS 316L K

P

PCTFE

kel-f

PEEK

N

V

E

NBR

nitrile

FKM

viton

EPDM

S

F

CV

L

xx

self-venting

filter

captured vent

locking cap

code for

special option

All regulators are marked with a typenumber, a drawingnumber and a unique serialnumber. Dutch Regulators stores the exact configuration of the regulator in the serialnumber.



Springloaded Pressure Regulator Model – GRT15S-16

Description The GRT15S-16 springloaded pressure regulator

reduces the supply pressure on the inletside to a controlled pressure on the outletside.

Specifications Inlet pressure 16 bar

Adjustable 0-3 bar - 2 pressure ranges Connections 1/2” NPT or BSPP

Seatdiameter 7 mm Cv / Kv Cv 1.0 / Kv 0.85

Fluids This pressure regulator is suitable for gases only.

Materials The regulator is made out of barstock stainless steel

material.

Body ss 316L Springhousing ss 316L

Valve ss 316L

Seat NBR, FKM or EPDM Valve spring ss 316

Setspring ss 302 O-rings / diaphragm NBR, FKM or EPDM



Technical details • all parts cleaned and degreased

• leak-tight seat design

• all regulators tested before delivery

Standards • EN 12516 - design

• EN 12266-1 - testing

• PED 2014/68/EU - SEP (article 4, paragraph 3)


190

37

Ø119

37

62Ø68




Options Many options are available. The most requested

options are mentioned below.

Materials Regulators can be produced in higher graded materials

than stainless steel 316L.

NACE - MR 0175

All wetted parts of the regulators can be supplied according to NACE MR 0175, including Inconel X750

valvespring and a NACE report.

Spare parts Spare parts kits are available for the regulator. Mention the serial number in case you need spare parts for

existing regulators.

Dependency Character of the regulator is “dependency”.

The set-pressure will increase, when you have a decreasing inletpressure.

Dependency ratios are listed below.

• range 0-1 bar - 1:150

• range 0-3 bar - 1:150

The large diaphragm has a positive effect towards

dependency.

Flow The regulator has good flow performance over the

complete range. Ask for advice if this regulator is the best choice for your application.

Adjusting the regulator The regulator comes standard with a knob. The threadpiece below the knob is designed for

frequent adjustment.





Internals The internals of the regulator are important for the

performance. The different internals are mentioned below.

Diaphragm sensing

The model has a large diaphragm to handle pressures

below 3 bar accurately.

Rubber seated A rubber seat is less sensitive to dirt.

Valvespring and setspring

The valvespring gives high spring force to ensure seat-

tightness.

The setspring is produced according to our high quality specifications. The low spring rate ensures good

performance at high flow.

Gaugeports The regulator has standard one 1/4" NPT gaugeport to

measure the controlled setpressure.

Additional 1/4” NPT gaugeports are available, see option G1 and G2 below.

On request other gaugeport options available.

G1

G2

Standard Outlet gaugeport

Additional Outlet gaugeport

Additional Inlet and Outlet

gaugeport


Below ranges are available:

0-1 bar / 0-4 bar / 0-10 bar / 0-25 bar

• case diameter 63 mm

• internals ss 316

• bottom connection 1/4” NPT

Mounting The regulator can be mounted in every position

(horizontal / vertical).

The bottom of the regulator

has two mounting holes M5 with 8 mm thread and a C-C

distance of 35 mm.

For regulators installed outdoors, make sure that rain

cannot enter the springhousing or mount it drainable.

Section view

Section view of:

GRT15S-16N3-SSNN




Connections The regulator has threaded connections, designed for

compression fittings.


BSPP threads according to ISO 228-1 BSPP ports according to ISO 1179-1


Temperature The general temperature range of the regulator is -50 / 200 °C, but is often limited due to the used

sealing materials.

NBR seat / seals - 35 / 130 °C

FKM seat / seals - 20 / 200 °C EPDM seat / seals - 50 / 120 °C


Example : GRT15S - 16N3 - SSNN


GRT15S

16

: 16 bar

N

B

: 1/2” NPT

: 1/2” BSPP

1

3

: 0-1 bar

: 0-3 bar

SS

SS 316L

N

V

E

NBR

nitrile

FKM

viton

EPDM

N

V

E

NBR

nitrile

FKM

viton

EPDM

G1

G2

L

xx

one extra

gaugeport

two extra

gaugeports

locking cap

codes for

special option

All regulators are marked with a typenumber, a drawingnumber and a unique serialnumber.

Dutch Regulators stores the exact configuration of the regulator in the serialnumber.




Description The GRT15S springloaded pressure regulator reduces

the supply pressure on the inletside to a controlled pressure on the outletside.


Adjustable 0-50 bar - 4 pressure ranges Connections 1/2" NPT or BSPP


Fluids This pressure regulator is suitable for gases and

liquids.


Body ss 316L

Springhousing ss 316L

Valve ss 316L Seat NBR, FKM or EPDM

Valve spring ss 316 Setspring ss 302

O-rings / diaphragm NBR, FKM or EPDM


All metal parts are marked with a traceable batch

number. Material certificates are available on request.








Ø73

37

Ø68

37

62

183








Seals

Regulators can be equipped with FFKM + PTFE seals. Other compounds for higher or lower temperatures are

available.

NACE - MR 0175








• range 0-3 bar - 1:30

• range 0-8 bar - 1:30

• range 0-20 bar - 1:30

• range 0-50 bar - 1:10


complete range. Ask for advice if this regulator is the

best choice for your application.

Adjusting the regulator The regulator comes standard with a knob.

The threadpiece below the knob is designed for


Regulators that have a fixed setpoint, can be equipped

with a locking cap.






Diaphragm or piston sensing

Diaphragm sensed for pressure ranges

0-3 bar / 0-8 bar / 0-20 bar

Piston sensed for pressure range 0-50 bar

Rubber seated

A rubber seat is less sensitive to dirt.









G1

G2




gaugeport



0-4 bar / 0-10 bar / 0-25 bar / 0-60 bar








distance of 35 mm.



Section view

Section view of:

GRT15S-50N8-SSVV








Springhousing connection

The springhousing has a 1/8” NPT connection.

This connection functions as breathing hole or could

be used to pipe away hazardous fluids. Do not plug the connection.

Design pressure The design pressure applies for inlet and outletside.


sealing materials.



Typenumber explanation Example : GRT15S - 50N8 - SSVV


GRT15S

50

: 50 bar

N

B

: 1/2" NPT

: 1/2” BSPP

3

8

20

50

: 0-3 bar *

: 0-8 bar

: 0-20 bar

: 0-50 bar

SS

SS 316L

N

V

E

NBR

nitrile

FKM

viton

EPDM

N

V

E

NBR

nitrile

FKM

viton

EPDM

G1

G2

L

xx

one extra

gaugeport

two extra

gaugeports

locking cap

codes for

special option

* GRT15S-16 with large diaphragm available for higher accuracy in the ranges 0-1 and 0-3 bar








Specifications Inlet pressure 280 or 420 bar




liquids.


Body ss 316L


Valve ss 316L Seat PCTFE or PEEK













37

Ø68

37

62

191

Ø73








Seals


available.

NACE - MR 0175








• range 0-3 bar - 1:200

• range 0-8 bar - 1:200

• range 0-20 bar - 1:200

• range 0-50 bar - 1:70

• range 0-100 bar - 1:35

• range 0-280 bar - 1:13

• range 0-420 bar - 1:9

The balanced valve has a positive effect towards

dependency.

Flow The regulator has good flow performance over the complete range. Ask for advice if this regulator is the












0-3 bar / 0-8 bar / 0-20 bar

Piston sensed for pressure ranges 0-50 bar / 0-100 bar / 0-280 bar / 0-420 bar

Plastic seated

PCTFE recommended and seals easy.

PEEK recommended for liquid and high temperatures.

Valvespring and setspring The valvespring gives high spring force to ensure seat-

tightness.

The setspring is produced according to our high quality

specifications. The low spring rate ensures good performance at high flow.





G1

G2




gaugeport



0-4 bar / 0-10 bar / 0-25 bar / 0-60 bar / 0-160 bar /

0-400 bar / 0-600 bar






The bottom of the regulator has two mounting holes M5

with 8 mm thread and a C-C

distance of 35 mm.



Section view

Section view of: GRT15S-420N20-SSKN

Section view of:

GRT15S-420N100-SSKN














sealing materials.

PCTFE seat - 50 / 60 °C

PEEK seat - 50 / 200 °C NBR seals - 35 / 130 °C

FKM seals - 20 / 200 °C

EPDM seals - 50 / 120 °C


Example : GRT15S - 280N20 - SSKN


GRT15S

280

420

: 280 bar

: 420 bar

N

B

: 1/2" NPT

: 1/2” BSPP

3

8

20

50

100

280

420

: 0-3 bar *

: 0-8 bar

: 0-20 bar

: 0-50 bar

: 0-100 bar

: 0-280 bar

: 0-420 bar

SS

SS 316L

K

P

PCTFE

kel-f

PEEK

N

V

E

NBR

nitrile

FKM

viton

EPDM

G1

G2

L

xx

one extra

gaugeport

two extra

gaugeports

locking cap

codes for

special option









Adjustable 0-3 bar - 2 pressure ranges Connections 3/4” NPT or BSPP

Seatdiameter 9,5 mm Cv / Kv Cv 1.8 / Kv 1.5



Body ss 316L


Valve ss 316L Seat NBR, FKM or EPDM













54

246

45

Ø85

Ø160

76

Ø55








NACE - MR 0175








• range 0-1 bar - 1:3000

• range 0-3 bar - 1:3000

The large diaphragm and balanced valve have a

positive effect towards dependency.











Diaphragm sensing






tightness.







G1

G2




gaugeport



0-1 bar / 0-4 bar / 0-10 bar / 0-25 bar








distance of 45 mm.



Section view

Section view of:

GRT20S-16N3-SSNN










sealing materials.






GRT20S

16

: 16 bar

N

B

: 3/4” NPT

: 3/4” BSPP

1

3

: 0-1 bar

: 0-3 bar

SS

SS 316L

N

V

E

NBR

nitrile

FKM

viton

EPDM

N

V

E

NBR

nitrile

FKM

viton

EPDM

G1

G2

L

xx

one extra

gaugeport

two extra

gaugeports

locking cap

codes for

special option







Specifications Inlet pressure 50, 280 or 420 bar




liquids.


Body ss 316L


Valve ss 316L Seat PCTFE, PEEK or rubber













76

Ø55

45

Ø85

54

234








Seals


available.

NACE - MR 0175



Spare parts Spare parts kit is available for the regulator. Mention the serial number in case you need spare parts for





• range 0-3 bar - 1:350

• range 0-8 bar - 1:350

• range 0-20 bar - 1:350

• range 0-50 bar - 1:110

• range 0-100 bar - 1:55

• range 0-280 bar - 1:20

• range 0-420 bar - 1:14


dependency.













0-3 bar / 0-8 bar / 0-20 bar


Rubber or plastic seated

Rubber seats for design pressure up to 50 bar.


Plastic seats for design pressure above 50 bar. PCTFE recommended and seals easy.










G1

G2




gaugeport




0-400 bar / 0-600 bar








distance of 45 mm.



Section view

Section view of:

GRT20S-50B8-SSNN

Section view of:

GRT20S-420B280-SSNN













Seat materials The seat materials are related to the design pressure.

NBR, FKM or EPDM design pressure up to 50 bar

PCTFE or PEEK design pressure above 50 bar

Depending on temperature or special wishes, the seat material could be different as mentioned above.

Temperature The general temperature range of the regulator is

-50 / 200 °C, but is often limited due to the used sealing materials.

PCTFE seat - 50 / 60 °C PEEK seat - 50 / 200 °C

NBR seat / seals - 35 / 130 °C FKM seat / seals - 20 / 200 °C

EPDM seat / seals - 50 / 120 °C


Example : GRT20S - 280N100 - SSKN


GRT20S

50

280

420

: 50 bar

: 280 bar

: 420 bar

N

B

: 3/4" NPT

: 3/4” BSPP

3

8

20

50

100

280

420

: 0-3 bar *

: 0-8 bar

: 0-20 bar

: 0-50 bar

: 0-100 bar

: 0-280 bar

: 0-420 bar

SS

SS 316L

N

V

E

K

P

NBR

nitrile

FKM

viton

EPDM

PCTFE

kel-f

PEEK

N

V

E

NBR

nitrile

FKM

viton

EPDM

G1

G2

L

xx

one extra

gaugeport

two extra

gaugeports

locking cap

codes for

special option









Adjustable 0-3 bar - 2 pressure ranges Connections 1” NPT or BSPP




material.

Body ss 316L Springhousing ss 316L

Valve ss 316L












275

100

53

Ø160

61

88

Ø65








NACE - MR 0175








• range 0-1 bar - 1:2500

• range 0-3 bar - 1:2500





Adjusting the regulator The regulator comes standard with a setscrew.







Diaphragm sensing






tightness.







G1

G2




gaugeport



0-1 bar / 0-4 bar / 0-10 bar / 0-25 bar








distance of 50 mm.



Section view

Section view of:

GRT25S-16N3-SSNN










sealing materials.






GRT25S

16

: 16 bar

N

B

: 1” NPT

: 1” BSPP

1

3

: 0-1 bar

: 0-3 bar

SS

SS 316L

N

V

E

NBR

nitrile

FKM

viton

EPDM

N

V

E

NBR

nitrile

FKM

viton

EPDM

G1

G2

L

xx

one extra

gaugeport

two extra

gaugeports

locking cap

codes for

special option








Adjustable 0-420 bar - 7 pressure ranges Connections 1" NPT or BSPP



liquids.


Body ss 316L















51

Ø100

59

88

264








Seals


available.

NACE - MR 0175








• range 0-3 bar - 1:350

• range 0-8 bar - 1:350

• range 0-20 bar - 1:150

• range 0-50 bar - 1:50

• range 0-100 bar - 1:25

• range 0-280 bar - 1:9

• range 0-420 bar - 1:7


dependency.




Regulators that have a fixed setpoint, can be equipped

with a locking cap.








0-3 bar / 0-8 bar / 0-20 bar















G1 G2




gaugeport




0-400 bar / 0-600 bar








distance of 50 mm.



Section view

Section view of:

GRT25S-50B8-SSNN

Section view of:

GRT25S-420B100-SSKN-L























Example : GRT25S - 280B100 - SSKN


GRT25S

50

280

420

: 50 bar

: 280 bar

: 420 bar

N

B

: 1” NPT

: 1” BSPP

3

8

20

50

100

280

420

: 0-3 bar *

: 0-8 bar

: 0-20 bar

: 0-50 bar

: 0-100 bar

: 0-280 bar

: 0-420 bar

SS

SS 316L

N

V

E

K

P

NBR

nitrile

FKM

viton

EPDM

PCTFE

kel-f

PEEK

N

V

E

NBR

nitrile

FKM

viton

EPDM

G1

G2

L

xx

one extra

gaugeport

two extra

gaugeports

locking cap

codes for

special option





Domeloaded Pressure Regulator Model – GRT25D

Description The GRT25D domeloaded pressure regulator reduces



Adjustable 0-420 bar Connections 1” NPT or BSPP



liquids.


material.

Body ss 316L Dome ss 316L

Valve ss 316L

Seat PCTFE, PEEK or rubber Valve spring ss 316












148

52

88

Ø99








Seals


available.

NACE - MR 0175








• range 0-420 bar - 1:350

without pilot regulator

Dependency ratio is influenced by the mounted pilot regulator.


dependency.



Pilot regulator The regulator can be supplied with a mounted pilot

regulator. The pilot regulator provides the controlled pressure in dome.

Adjusting the regulator The regulator comes standard with two 1/4” NPT dome connections. The setpressure of the regulator

equals to the pressure in the dome.






Diaphragm sensing

Diaphragm sensed for all ranges.


Rubber seats for design pressure up to 50 bar. A rubber seat is less sensitive to dirt.

Plastic seats for design pressure above 50 bar.



Valvespring The valvespring gives high spring force to ensure seat-

tightness.





When the regulator is pilot operated, the standard gaugeport is used to mount the pilot regulator.

G1

G2




gaugeport

Section view

Section view of:

GRT25D-420N420-SSKN



0-4 bar / 0-10 bar / 0-25 bar / 0-60 bar / 0-160 bar / 0-400 bar / 0-600 bar





The bottom of the regulator has two mounting holes M6 with 8 mm thread and a C-C distance of 50 mm.








Dome connections

The regulator has two 1/4” NPT dome connections.












Example : GRT25D - 280N20 - SSKN - PO


GRT25D

50

280

420

: 50 bar

: 280 bar

: 420 bar

N

B

: 1" NPT

: 1” BSPP

X

: 0-X bar

range

depending

on the

mounted

pilot

regulator

SS

SS 316L

N

V

E

K

P

NBR

nitrile

FKM

viton

EPDM

PCTFE

kel-f

Peek

N

V

E

NBR

nitrile

FKM

viton

EPDM

PO

xx

pilot operated

codes for

special option









Adjustable 0-3 bar Connections 1 1/2" NPT or 1 1/2” BSPP




material.

Body ss 316L

Springhousing ss 316L Valve ss 316L










• PED 2014/68/EU - CAT I


320Ø190

61

112








NACE - MR 0175








• range 0-1 bar - 1:1700

• range 0-3 bar - 1:1700











Diaphragm sensing






tightness.



Gaugeports The regulator has standard two 1/4" NPT gaugeports

to measure the inlet and outletpressure.

On request it is possible to have additional gaugeports.


Below ranges are available: 0-4 bar / 0-10 bar / 0-25 bar







Section view

Section view of:

GRT40S-16N1-SSVV










sealing materials.



Typenumber explanation Example : GRT40S - 16N3 - SSNN


GRT40S

16

: 16 bar

N

B

: 1 1/2" NPT

: 1 1/2” BSPP

1

3

: 0-1 bar

: 0-3 bar

SS

SS 316L

N

V

E

NBR

nitrile

FKM

viton

EPDM

N

V

E

NBR

nitrile

FKM

viton

EPDM

xx

codes for

special option








Adjustable 0-280 bar - 6 pressure ranges Connections 1 1/2" NPT or BSPP



liquids.


Body ss 316L













• PED 2014/68/EU - CAT I (optional CAT II)


320

Ø125

61

112








Seals

Compounds for higher or lower temperatures are available.

NACE - MR 0175

All wetted parts of the regulators can be supplied

according to NACE MR 0175, including Inconel X750 valvespring and a NACE report.

Spare parts Spare parts kit is available for the regulator. Mention

the serial number in case you need spare parts for existing regulators.

Dependency A character of the regulator is “dependency”.

The set-pressure will change, when you have a changing inletpressure.

Dependency ratios are available on request.

The balanced valve has a positive effect towards dependency.











0-3 bar / 0-8 bar / 0-20 bar

Piston sensed for pressure ranges 0-50 bar / 0-100 bar / 0-280 bar






Valvespring








Below ranges are available: 0-4 bar / 0-10 bar / 0-25 bar / 0-60 bar / 0-160 bar /

0-400 bar / 0-600 bar








Section view

Section view of:

GRT40S-280B8-SSKN









The model with a 420 bar design pressure has a

design pressure on the outletside of 280 bar.


NBR, FKM or EPDM design pressure up to 50 bar PCTFE or PEEK design pressure above 50 bar





PEEK seat - 50 / 200 °C



Typenumber explanation Example : GRT40S – 50N20 – SSVV


GRT40S

50

280

420

: 50 bar

: 280 bar

: 420 bar

N

B

: 1 1/2" NPT

: 1 1/2” BSPP

3

8

20

50

100

280

: 0-3 bar *

: 0-8 bar

: 0-20 bar

: 0-50 bar

: 0-100 bar

: 0-280 bar

SS

SS 316L

N

V

E

K

P

NBR

nitrile

FKM

viton

EPDM

PCTFE

kel-f

PEEK

N

V

E

NBR

nitrile

FKM

viton

EPDM

xx

codes for

special option









Adjustable 0-280 bar Connections 1 1/2” NPT or 1 1/2” BSPP



liquids.


material.

Body ss 316L Dome ss 316L

Valve ss 316L

Seat PCTFE, PEEK or rubber Valve spring ss 316












168

61

112

Ø125








Seals


available.

NACE - MR 0175








• range 0-280 bar - 1:280




dependency.





External feedback The pilot regulator can be supplied with an external

feedback from the outlet of the main regulator, back to the pilot regulator. The external feedback improves the

performance of the regulator.

The external feedback option is available for design pressures up to 50 bar.








Diaphragm sensing








tightness.







0-400 bar






For regulators installed outdoors, make sure that rain cannot enter the springhousing or mount it drainable.

Section view

Section view of:

GRT40D-280N280-SSKN








Dome connections











PEEK seat - 50 / 200 °C



Typenumber explanation Example : GRT40D – 50B20 – SSNN – PO – EF


GRT40D

50

280

420

: 50 bar

: 280 bar

: 420 bar

(280 bar for

outlet side)

N

B

: 1 1/2” NPT

: 1 1/2” BSPP

X

: 0-X bar

range

depending

on the

mounted

pilot

regulator

SS

SS 316L

N

V

E

K

P

NBR

nitrile

FKM

viton

EPDM

PCTFE

kel-f

Peek

N

V

E

NBR

nitrile

FKM

viton

EPDM

PO

EF

xx

pilot

operated

external

feedback

codes for

special option








Adjustable 0-280 bar Connections 2” BSPP

Seatdiameter 22,5 mm Cv / Kv Cv 10 / Kv 8.8


liquids.


Body ss 316L

Dome ss 316L


Valve spring ss 316 O-rings / diaphragm NBR, FKM or EPDM










193

75

130

Ø150

Ø125








Seals


available.

NACE - MR 0175








• range 0-280 bar - 1:400




dependency.





External feedback The pilot regulator can be supplied with an external

feedback from the outlet of the main regulator, back to the pilot regulator. The external feedback improves the

performance of the regulator.

The external feedback option is available for design

pressures up to 50 bar.








Diaphragm sensing








tightness.







0-400 bar






For regulators installed outdoors, make sure that rain cannot enter the springhousing or mount it drainable.

Section view

Section view of:

GRT50D-50B50-SSNN






Line connections BSPP threads according to ISO 228-1

BSPP ports according to ISO 1179-1

Dome connections











PEEK seat - 50 / 200 °C




Example : GRT50D – 50B50 – SSNN – PO


GRT50D

50

280

420

: 50 bar

: 280 bar

: 420 bar

(280 bar for

outlet side)

B

: 2” BSPP

X

: 0-X bar

range

depending

on the

mounted

pilot

regulator

SS

SS 316L

N

V

E

K

P

NBR

nitrile

FKM

viton

EPDM

PCTFE

kel-f

Peek

N

V

E

NBR

nitrile

FKM

viton

EPDM

PO

EF

xx

pilot

operated

external

feedback

codes for

special option


Date post:	10-Nov-2018
Category:	Documents
Upload:	nguyendiep
View:	240 times
Download:	0 times

General Threaded Pressure Regulators - Gommer · General Threaded Pressure Regulators ... O-rings...

Documents