GETTING STARTED - HP

GETTING STARTED

Getting Started

© Copyright 2012 Hewlett-PackardDevelopment Company, L.P.

AMD and AMD Catalyst are trademarks ofAdvanced Micro Devices, Inc.Bluetooth is atrademark owned by its proprietor and usedby Hewlett-Packard Company underlicense. Intel is a trademark of IntelCorporation in the U.S. and other countries.Microsoft and Windows are U.S. registeredtrademarks of Microsoft Corporation. SDLogo is a trademark of its proprietor.

The information contained herein is subjectto change without notice. The onlywarranties for HP products and services areset forth in the express warranty statementsaccompanying such products and services.Nothing herein should be construed asconstituting an additional warranty. HP shallnot be liable for technical or editorial errorsor omissions contained herein.

First Edition: April 2012

Document Part Number: 677493-001

Product notice

This guide describes features that arecommon to most models. Some featuresmay not be available on your computer.

Software terms

By installing, copying, downloading, orotherwise using any software productpreinstalled on this computer, you agree tobe bound by the terms of the HP End UserLicense Agreement (EULA). If you do notaccept these license terms, your soleremedy is to return the entire unusedproduct (hardware and software) within 14days for a refund subject to the refundpolicy of your place of purchase.

For any further information or for requestinga full refund of the computer, pleasecontact your local point of sale (the seller).

User guides

HP is committed to reducing theenvironmental impact of our products. Aspart of this effort, we provide user guidesand learning centers on your computer harddrive in Help and Support. Additionalsupport and updates to the user guides areavailable on the Web.

Safety warning noticeWARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do notplace the computer directly on your lap or obstruct the computer air vents. Use the computer only ona hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a softsurface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter tocontact the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computerand the AC adapter comply with the user-accessible surface temperature limits defined by theInternational Standard for Safety of Information Technology Equipment (IEC 60950).

v

vi Safety warning notice

Table of contents

1 Welcome .......................................................................................................................................................... 1What's new ........................................................................................................................................... 2

Audio .................................................................................................................................... 2Volume dial ......................................................................................................... 2Beats Audio ......................................................................................................... 3

Accessing Beats Audio Control Panel ................................................ 3Enabling and Disabling Beats Audio .................................................. 4

HP Wireless Audio .............................................................................................. 5HP Wireless Audio Manager .............................................................. 5

Refreshing your software content (select models only) ....................................................... 6Radiance backlight keyboard and proximity sensor ............................................................ 6HP CoolSense ..................................................................................................................... 7HP 3D Cinema Technology ................................................................................................. 7Intel Wireless Display .......................................................................................................... 7Switching between graphics modes .................................................................................... 7AMD Eyefinity Multi-Display technology .............................................................................. 8

Example display configuration for SLS ............................................................... 8Switching the screen image ................................................................................ 8Using AMD Catalyst Control Center .................................................................... 9

Finding information ............................................................................................................................... 9

2 Using HP 3D Cinema Technology ............................................................................................................... 113D safety information ......................................................................................................................... 12What are stereoscopic vision and 3D ................................................................................................. 13What is HP 3D Cinema Technology ................................................................................................... 14Using the HP 3D Active Shutter Glasses ........................................................................................... 15

Identifying the 3D glasses components ............................................................................. 15Turning the 3D glasses on or off ........................................................................................ 16

Using 3D Cinema Technology ............................................................................................................ 16Supported 3D formats ........................................................................................................................ 17Using CyberLink PowerDVD .............................................................................................................. 17Viewing 2D Blu-ray Discs in 3D .......................................................................................................... 18

vii

Playing 3D games .............................................................................................................................. 18Viewing 3D content on a 3D TV ......................................................................................................... 18Caring for the 3D glasses ................................................................................................................... 19

Using the nose pieces ....................................................................................................... 19Replacing the battery ......................................................................................................... 20Cleaning the 3D glasses .................................................................................................... 21Handling the glasses ......................................................................................................... 22

Frequently asked questions ............................................................................................................... 22Why can't I see 3D content ................................................................................................ 22What 3D formats are supported on my computer .............................................................. 22Can I play stereoscopic 3D games on my computer ......................................................... 22Can I use the 3D glasses to view a 3D movie in a movie theater ...................................... 23Can I wear my 3D glasses over my prescription glasses .................................................. 23How do I clean my 3D glasses .......................................................................................... 23How close do I need to be to the computer to view 3D content ......................................... 23Why do I see flickering when I watch 3D content .............................................................. 23Can I use the 3D glasses in bright sunlight next to a window ............................................ 23What type of batteries do I need for the 3D glasses .......................................................... 23Can I use my computer to watch 3D content on my external 3D TV ................................. 23

3 Getting to know your computer ................................................................................................................... 24Top ..................................................................................................................................................... 24

Imagepad ........................................................................................................................... 24Lights ................................................................................................................................. 25Buttons and speakers ........................................................................................................ 26Keys ................................................................................................................................... 27

Front ................................................................................................................................................... 28Right side ........................................................................................................................................... 29Left side .............................................................................................................................................. 31Display ................................................................................................................................................ 32Bottom ................................................................................................................................................ 33

4 Networking .................................................................................................................................................... 34Using an Internet service provider (ISP) ............................................................................................ 35Connecting to a wireless network ....................................................................................................... 35

Connecting to an existing WLAN ....................................................................................... 36Setting up a new WLAN network ....................................................................................... 36

Configuring a wireless router ............................................................................ 37Protecting your WLAN ....................................................................................... 37

viii

5 Keyboard and pointing devices ................................................................................................................... 38Using the keyboard ............................................................................................................................ 38

Using the action keys ......................................................................................................... 38Using the integrated numeric keypad ................................................................................ 40

Using pointing devices ....................................................................................................................... 41Setting pointing device preferences ................................................................................... 41Using the Imagepad ........................................................................................................... 42

Turning the Imagepad off or on ......................................................................... 42Navigating ......................................................................................................... 43Selecting ........................................................................................................... 43Using Imagepad gestures ................................................................................. 43

Scrolling ............................................................................................ 44Pinching/Zooming ............................................................................. 44Rotating ............................................................................................ 45Flicking ............................................................................................. 45

6 Maintenance .................................................................................................................................................. 46Using a factory-sealed battery ............................................................................................................ 46Replacing or upgrading the hard drives ............................................................................................. 47

Removing and installing the primary hard drive ................................................................. 47Removing the primary hard drive ...................................................................... 47Installing the primary hard drive ........................................................................ 49

Removing and inserting the secondary hard drive ............................................................ 52Removing the secondary hard drive ................................................................. 52Installing the secondary hard drive ................................................................... 54

Adding or replacing memory modules ................................................................................................ 57

7 Backup and recovery .................................................................................................................................... 62Restore ............................................................................................................................................... 63Creating recovery media .................................................................................................................... 64Performing a system restore .............................................................................................................. 64

Restoring using the dedicated recovery partition (select models only) .............................. 65Restoring using the recovery media .................................................................................. 65Changing the computer boot order .................................................................................... 66

Backing up and recovering your information ...................................................................................... 66Using Windows Backup and Restore ................................................................................ 67Using Windows system restore points ............................................................................... 67

When to create restore points ........................................................................... 67Create a system restore point ........................................................................... 68Restore to a previous date and time ................................................................. 68

ix

8 Customer support ......................................................................................................................................... 69Contacting customer support ............................................................................................................. 69Labels ................................................................................................................................................. 70

9 Specifications ................................................................................................................................................ 71Input power ......................................................................................................................................... 71Operating environment ....................................................................................................................... 72

Index ................................................................................................................................................................... 73

x

1 Welcome

The following sections are included in this chapter:

● What's new

● Finding information

Before you set up and register your computer, plug the AC adapter into the computer and connect toexternal power. With external power connected, press the power button to begin charging the battery,and then follow the on-screen instructions.

After you set up and register the computer, it is important to take the following steps:

1. Set up your wired or wireless network. For more information, see Networking on page 34.

2. Create recovery discs or a recovery flash drive. For instructions, see Backup and recoveryon page 62.

3. Get to know your computer. See Getting to know your computer on page 24 and Keyboardand pointing devices on page 38.

4. Discover the software that is already loaded on the computer by selecting Start > All Programs.

1

What's newAudio

Volume dialLike the dial on a stereo, the integrated volume dial controls speaker volume on the computer.

▲ To increase speaker volume, rotate the dial clockwise.

– or –

▲ To decrease speaker volume, rotate the dial counter-clockwise.

NOTE: You can manually adjust the volume settings in Beats Audio Control Panel. For moreinformation, see Accessing Beats Audio Control Panel on page 3.

2 Chapter 1 Welcome

Beats AudioBeats Audio is an enhanced audio feature that provides a deep, controlled bass while maintaining aclear sound.

Accessing Beats Audio Control Panel

Beats Audio Control Panel allows you to view and manually control audio and bass settings.

To open Beats Audio Control Panel, do one of the following:

▲ Press the Beats Audio button located in the center of the volume dial.

– or –

▲ Select Start > Control Panel > Hardware and Sound > Beats Audio Control Panel.

What's new 3

Enabling and Disabling Beats Audio

▲ To enable or disable Beats Audio, press the fn key (1) and the b key (2).

The following table explains the meaning of the Beats Audio icons that appear on the screen, whenyou press the Beats Audio hot key (fn+b).

Icon Meaning

Beats Audio is enabled.

Beats Audio is disabled.

4 Chapter 1 Welcome

HP Wireless AudioHP Wireless Audio helps you set up a wireless sound system in your home that streams audio fromyour computer to a compatible set of wireless-enabled speakers or other audio devices.

NOTE: HP Wireless Audio uses KleerNet technology, and is not compatible with other wirelesstechnologies. Your wireless audio devices must also be compatible with HP Wireless Audio andKleerNet technology. To purchase compatible wireless audio devices, go to http://www.hp.com or aretailer near you.

HP Wireless Audio Manager

With HP Wireless Audio Manager, you can add, remove, name, and group wireless-enabled devicesin your home audio system.

NOTE: Before you start HP Wireless Audio Manager, be sure that the wireless device is turned on(the wireless light on the f12 key is white).

To access HP Wireless Audio Manager, do one of the following:

▲ Right-click the HP Wireless Audio icon in the notification area, at the far right of the task bar,and then click Launch Manager.

NOTE: If you are concerned about battery life, disable HP Wireless Audio when you are notusing it. Right-click the icon in the notification area and select Disable HP Wireless Audio. Tore-enable the software, right-click the icon in the notification area and select Enable HPWireless Audio.

– or –

▲ Select Start > Control Panel > Hardware and Sound > HP Wireless Audio.

NOTE: For more information on HP Wireless Audio, see the software Help.

What's new 5

http://www.hp.com

Refreshing your software content (select models only)When the computer is in the Sleep state, Intel® Smart Connect Technology periodically causes thecomputer to exit Sleep. Smart Connect then updates the content for certain open applications and re-initiates Sleep. As a result, your work is immediately available to you as soon as you exit Sleep. Youdo not have to wait while updates are downloaded.

▲ To open Intel Smart Connect to enable this feature or manually adjust the settings, select Start> All Programs > Intel > Intel Smart Connect Technology.

For additional information and a list of supported applications, see the software Help.

Radiance backlight keyboard and proximity sensorThe radiance backlight keyboard feature, turned on at the factory, uses proximity sensor technologyto automatically light up the keyboard when the sensors detect your presence in front of thecomputer. The proximity sensors, also turned on at the factory, automatically turn the radiancebacklight keyboard feature on or off based on your location.

▲ To turn the radiance backlight keyboard feature off or on, press the keyboard backlight actionkey (f5).

▲ To switch between low, medium, and high brightness levels, press and hold the keyboardbacklight action key (f5) in combination with either the up or down arrow key.

▲ To change the proximity sensor settings, select Start > All Programs > HP > HP ProximitySensor.

6 Chapter 1 Welcome

HP CoolSense

HP CoolSense automatically detects when the computer is not in a stationary position and

adjusts performance and fan settings to keep the surface temperature of your computer at theoptimum level of comfort.

When HP CoolSense is off, the position of the computer is not detected and the performance and fanoptions remain at the factory setting. As a result, the surface temperature of the computer may behigher than it would be with HP CoolSense on.

To turn CoolSense off or on, follow these steps:

1. Select Start > Control Panel > Hardware and Sound > HP CoolSense.

2. Select the On or Off check box.

HP 3D Cinema TechnologyHP 3D Cinema Technology provides cinema-quality viewing of stereoscopic 3D Blu-ray Disc movies,stereo 3D game play, and vivid 3D photos and videos. The integrated 3D features, along with the 3Dglasses, provide everything you need for an outstanding 3D sensory experience. For moreinformation, see Using HP 3D Cinema Technology on page 11.

NOTE: Before using 3D Cinema Technology and the 3D glasses, read the 3D safety information.Consult a physician if you suspect that you may have a physical problem seeing stereoscopic 3D. Formore information, see 3D safety information on page 12.

Intel Wireless DisplayIntel Wireless Display allows you to transmit your computer content wirelessly to your receiver/displaydevice, such as HDTV, monitor, projector, game console, Blu-ray player, or DVR, by using anoptional wireless adapter (purchased separately). For details about using the wireless adapter, seethe manufacturer's instructions.

▲ To open Intel Wireless Display, select Start > All Programs > Intel WiDi.

NOTE: Before you can use the wireless display feature, the computer wireless feature must beturned on and the computer graphics must be set to power-saving mode.

Switching between graphics modesThe computer is equipped with switchable graphics and has two modes for processing graphics.When you switch from AC power to battery power, the computer can switch from using the high-performance mode to using the power-saving mode. Conversely, when you switch from battery powerto AC power, the computer can switch back to the high-performance mode.

NOTE: 3D playback on the computer display requires a high-performance graphics processing unit(GPU).

NOTE: In order to optimize the performance of the computer, the system may not allow you toswitch modes, or it may prompt you to switch. You may need to close all programs before switching.

When you switch between AC and battery power, you are notified that the computer is preparing toswitch graphics modes. You can then choose to either continue to use the same graphics mode or toswitch. If you choose to switch, the screen goes blank for a few seconds. When the switch iscomplete, a message appears in the notification area, and the screen image reappears.

What's new 7

AMD Eyefinity Multi-Display technologyNOTE: 3D playback is not supported on AMD Eyefinity technology.

Your computer supports the new AMD Eyefinity technology, which provides the following features:

● You can connect up to 3 external displays, as long as at least one of the displays is connected toa DisplayPort on the computer.

NOTE: You cannot use an adapter on either DisplayPort.

● You can span the screen image across as many as 3 external displays into a massive singlelarge surface (SLS).

NOTE: When you do this, the computer display is turned off.

Example display configuration for SLSIn this example, 3 external displays are connected to the computer using the two DisplayPorts andthe HDMI port.

NOTE: External displays in an SLS must have identical resolution settings. Change the settings asneeded to comply with this requirement.

NOTE: Windows 7® supports only 2 external displays. To configure 3 external displays in Windows7, See Using AMD Catalyst Control Center on page 9.

Switching the screen imagePress the switch screen image action key (f4) to open a dialog box that allows you to select one of 4configuration choices.

● Computer only—Turns off any external displays and shows the image only on only the computerdisplay.

● Duplicate—Clones the image on the computer display onto an external display that is connectedto the computer.

● Extend—Extends the screen image across the computer display and all connected externaldisplays.

● Projector only—Turns off the computer display and extends the screen image across allconnected external displays.

NOTE: To manage the video output devices and default output devices, use AMD Catalyst™Control Center.

8 Chapter 1 Welcome

Using AMD Catalyst Control CenterTo configure the display output and to manage AMD Eyefinity technology, use AMD Catalyst ControlCenter.

▲ To open AMD Catalyst Control Center, right-click the desktop and click Graphics Properties.

NOTE: For additional information about using AMD Catalyst Control Center, see the software Help.

Finding informationYou have already used Setup Instructions to turn on the computer and locate this guide. For productdetails, how-to information, and more, use this table.

Resources Contents

Setup Instructions poster Overview of computer features.

HP Notebook Reference Guide

To access this guide, select Start > Help andSupport > User guides.

● Power management features

● Instructions for the following:

◦ Maximizing battery life

◦ Using the multimedia features of the computer

◦ Protecting the computer

◦ Caring for the computer

◦ Updating the software

Help and Support

To access Help and Support, select Start > Help andSupport. For more details, go to http://www.hp.com/support.

A broad range of how-to information and troubleshooting tips.

Regulatory, Safety and Environmental Notices

To access this guide, select Start > Help andSupport > User guides.

Important regulatory notices, including proper battery disposalinformation.

Safety & Comfort Guide

To access this guide, select Start > Help andSupport > User guides, or go to http://www.hp.com/ergo.

● Proper workstation setup

● Guidelines for posture and work habits that maximize yourcomfort and decrease your risk of injury

● Electrical and mechanical safety information

Worldwide Telephone Numbers

This booklet is provided with your computer.

HP Customer Support phone numbers.

HP website

To access this website, go to http://www.hp.com/support.

● Customer support information

● Ordering parts and finding additional help

● Software, driver, and BIOS updates

● Information about accessories for the computer

Finding information 9

http://www.hp.com/support


http://www.hp.com/ergo

http://www.hp.com/ergo



Resources Contents

Limited Warranty*

To access the warranty, select Start > Help andSupport > User guides, or go to http://www.hp.com/go/orderdocuments.

Specific warranty information about this computer.

*You can find the expressly provided HP Limited Warranty applicable to your product located with the user guides on yourcomputer and/or on the CD/DVD provided in the box. In some countries/regions, HP may provide a printed HP LimitedWarranty in the box. For some countries/regions where the warranty is not provided in printed format, you may request aprinted copy from http://www.hp.com/go/orderdocuments or write to:

● North America: Hewlett-Packard, MS POD, 11311 Chinden Blvd, Boise, ID 83714, USA

● Europe, Middle East, Africa: Hewlett-Packard, POD, Via G. Di Vittorio, 9, 20063, Cernusco s/Naviglio (MI), Italy

● Asia Pacific: Hewlett-Packard, POD, P.O. Box 200, Alexandra Post Office, Singapore 911507

When you request a printed copy of your warranty, please include your product number, warranty period (found on yourserial number label), name, and postal address.

IMPORTANT: Do NOT return your HP product to the addresses above. For U.S. product support, go to http://www.hp.com/go/contactHP. For worldwide product support, go to http://welcome.hp.com/country/us/en/wwcontact_us.html.

10 Chapter 1 Welcome

http://www.hp.com/go/orderdocuments



http://www.hp.com/go/contactHP


http://welcome.hp.com/country/us/en/wwcontact_us.html

2 Using HP 3D Cinema Technology


● 3D safety information

● What are stereoscopic vision and 3D

● What is HP 3D Cinema Technology

● Using the HP 3D Active Shutter Glasses

● Using 3D Cinema Technology

● Supported 3D formats

● Using CyberLink PowerDVD

● Viewing 2D Blu-ray Discs in 3D

● Playing 3D games

● Viewing 3D content on a 3D TV

● Caring for the 3D glasses

● Frequently asked questions

11

3D safety informationCarefully read all of the following safety precautions before using the 3D glasses and 3D CinemaTechnology.

WARNING! If you cannot see 3D content after you set up 3D Cinema Technology, HP recommendsthat you discontinue use. Consult a physician if you suspect a physical problem seeing stereoscopic3D.

Photosensitive Epileptic Seizures—Some individuals may experience a seizure or othercomplications when exposed to certain visual images, including flashing lights or patterns that mayappear in 3D content. If you or any of your relatives have a history of seizures or epilepsy, consult aphysician before using the 3D glasses and 3D Cinema Technology. Even those without a personalfamily history of epilepsy or stroke may have an undiagnosed condition that can cause photosensitiveepileptic seizures.

If you experience any of the following symptoms, immediately stop watching 3D content and consult aphysician: altered vision, light-headedness, dizziness, involuntary movements such as eye ormuscle twitching, convulsions, nausea, loss of awareness, confusion, cramps, and/ordisorientation. Parents should monitor and ask their children if they have any of the abovesymptoms. Children and teenagers may be more likely to experience these symptoms than adults.

Do not watch 3D content when you feel sleepy, tired, or sick. Watching 3D with the 3D glasses for anextended period of time may cause a headache or fatigue. If you feel headache, fatigue, or dizziness,stop using the 3D glasses and rest.

Your vision can change to accommodate viewing through the 3D glasses. After removing the 3Dglasses, wait several minutes before resuming regular activities.

Some 3D content may startle viewers. People who are pregnant, elderly, or epileptic, and thosesuffering from severe physical conditions are advised to avoid using the computer's 3D functionality.

The vision of young children (especially children under the age of 6) is still under development.Consult your doctor (such as a pediatrician or eye doctor) before allowing young children to watch 3Dvideo images or play 3D video games. Parents or guardians should supervise young children toensure that they follow these recommendations.

Choking Hazard—The 3D glasses contain small parts and are not intended for babies and smallchildren.

Do not use the 3D glasses near water.

The lenses in the 3D glasses contain glass. To reduce the risk of damage to the lenses, use cautionwhen using the glasses and properly store them when not in use. Do not use the glasses if there isany sign of damage or cracking in the lenses.

The 3D glasses are not prescription eyewear, sunglasses, or protective goggles. To reduce the risk ofpersonal injury, do not use the glasses for any general eyewear purposes.

12 Chapter 2 Using HP 3D Cinema Technology

What are stereoscopic vision and 3DWhen you see the world through both eyes, you are actually looking at two pictures merged into one.Your right eye and your left eye each deliver a separate image to your brain, which meshes these twoimages into one, three-dimensional picture.

Most movies in the past were only able to provide one image on the screen, and 3D effects had to besimulated by other means. However, the HP 3D Active Shutter Glasses provide a different view foreach eye, which more closely simulates 3D vision.

Each scene of the 3D content has two images, one drawn from the right eye view and the other fromthe left eye view. The computer display shows these alternating views so fast that your eyes cannotsee the change.

The 3D glasses are equipped with shutters in each lens. When the right eye image is displayed onthe screen, the left lens of the 3D glasses is closed, allowing only the right eye to see the image.When the left eye image is displayed, the process is reversed and only the left eye can see theimage. These images alternate so quickly that the eyes only see one smooth picture, making it looklike you are actually inside a 3D environment.

What are stereoscopic vision and 3D 13

What is HP 3D Cinema Technology3D Cinema Technology delivers vivid Blu-ray Disc 3D content without the need for additional softwareand provides the following features:

● 3D technology specifically designed and optimized for 3D Blu-ray Disc content

● 3D Active Shutter Glasses that wirelessly synchronize with the 3D computer display

● 3D full high-definition 1080p display

● TriDef 3D Experience Ignition Game Player

● CyberLink PowerDVD

NOTE: Select computer models include 3D content so you can immediately begin enjoying 3D.

The computer supports both 2D and 3D formats. The computer operates in standard 2D mode untilstereoscopic 3D is detected and the 3D glasses are activated.


Using the HP 3D Active Shutter GlassesYour 3D experience begins with active 3D content and the 3D glasses, designed to fit over moststandard prescription glasses. The 3D glasses are battery powered and linked wirelessly to theinfrared (IR) emitters in your 3D computer.

WARNING! Before using the 3D glasses, read the 3D safety information on page 12.

NOTE: For optimal 3D viewing, sit within approximately 1.5 meters (5 feet) of the computer display.This distance varies depending on your viewing angle.

When watching stereoscopic 3D images, do not incline your head relative to the horizontal directionof the images.

Keep the areas immediately around the IR emitters free from obstructions. For information on thelocation of the IR emitters, see Getting to know your computer on page 24.

NOTE: Before using the glasses, remove the clear protective film from both sides of the lenses(select models only).

Identifying the 3D glasses components

Component

(1) Battery compartment

NOTE: The battery is preinstalled and may include a protective tab. If so, pull the tab to remove it.

(2) Nose pieces (3)

NOTE: The 3D glasses come with 3 nose pieces in different sizes. One nose piece is installed at the factory,and two additional nose pieces are included with the glasses.

Using the HP 3D Active Shutter Glasses 15

Turning the 3D glasses on or off● The 3D glasses turn on and off automatically. There is no on or off switch.

● When 3D content begins to play, the glasses detect an IR signal from the computer and turn onautomatically.

● Once the 3D content begins to play, the lenses may appear to darken and you may see someflickering as the glasses begin to turn on.

● The battery installed in the glasses provides approximately 150 hours of 3D viewing time. Tohelp conserve battery power, the glasses enter Standby if no IR signal is detected for 5 seconds.

Using 3D Cinema TechnologyAfter you set up your 3D computer, you are ready to verify that you can properly view the 3D content.

NOTE: Be sure that your computer is connected to AC power when you view 3D content. 3Dplayback on the computer display requires a high-performance graphics processing unit (GPU).

NOTE: The stereoscopic 3D effect works best in a darkened room. For optimal 3D viewing, thescreen brightness controls are disabled when watching 3D content.

NOTE: When watching 3D media, be sure that the keyboard backlight is turned off.

1. To access 3D content, do one of the following:

● Double-click the 3D demo icon on the computer desktop, and select a 3D clip from themenu.

● Insert a Blu-ray Disc 3D movie (purchased separately) into the slot-load optical drive on thecomputer, and follow the on-screen instructions.

NOTE: Insert the disc into the optical drive until it clicks into place. To eject the disc, pressthe optical drive eject action key (f10).

2. Put on your 3D glasses. If adjustment is needed, use the nose pieces that are provided.

3. The 3D glasses turn on automatically when the 3D content begins to play and the infrared (IR)signal is detected. Your lenses may darken, or you may see flickering while the glasses startoperation.

If you can see clearly in 3D, the setup is complete and you can begin viewing 3D cinemacontent.

NOTE: Differences in the frequencies at which the lighting in your room and 3D CinemaTechnology operate may cause flickering or interfere with the operation of the glasses. Resolvethis issue by dimming or turning off the lights.

WARNING! If you still cannot see 3D content, remove the 3D glasses and stop using 3DCinema Technology. Read the 3D safety information on page 12, and consult a physician if yoususpect a physical problem seeing stereoscopic 3D.


Supported 3D formatsYour computer supports the following 3D formats:

● Blu-ray Disc 3D movies

● Stereoscopic 3D games

● 3D MPEG 4 MVC files for 3D video playback

● 3D H.264 MVC and Fujifilm AVI dual-stream video file formats for 3D video playback

● 3D Fujifilm MPO for 3D photo viewing

Using CyberLink PowerDVDCyberLink PowerDVD supports the playback of 3D Blu-ray Discs, 3D video files, and native 3D

photos. When you insert a native 3D Blu-ray Disc, or play a native 3D video or photo file, itautomatically plays back in 3D if 3D mode is enabled.

During playback, you can also manually adjust the 3D configuration settings for improvedstereoscopic 3D viewing. For information on using CyberLink PowerDVD, see the software Help.

To open CyberLink PowerDVD, do one of the following:

▲ Select Start > All Programs > CyberLink, and then click CyberLink PowerDVD 10.

–or–

Click the CyberLink PowerDVD icon notification area, at the far right of the task bar.

Supported 3D formats 17

Viewing 2D Blu-ray Discs in 3DBecause PowerDVD lets you watch any existing 2D Blu-ray Disc movie in 3D, you no longer need towait for Blu-ray Disc 3D titles. You can enjoy 3D viewing right now from your own Blu-ray Disccollection.

1. Insert any 2D Blu-ray Disc movie (purchased separately) into the optical drive on the computer.

2. If PowerDVD does not open automatically, select Start > All Programs > CyberLink, and thenclick CyberLink PowerDVD 10.

3. Click the 3D button in the bottom toolbar.

Your movie begins playing in 3D.

4. Put on your 3D glasses. The 3D glasses turn on automatically when the 3D content begins toplay and the infrared (IR) signal is detected. Your lenses may darken, or you may see flickeringwhile the glasses start operation.

Playing 3D gamesYou can play stereo 3D games on your computer using TriDef 3D Experience Ignition Game Player.

▲ Select Start > All Programs > TriDef 3D > TriDef 3D Ignition.

Viewing 3D content on a 3D TVThe HDMI port allows you to play Blu-ray Disc 3D movies on an external 3D HDTV or 3D projector(purchased separately).

To view content on a 3D TV:

● The computer must be in Projector only mode.

● The computer must be connected to the TV with a high-speed HDMI cable.

● You must use the 3D glasses that came with your TV, not the glasses that came with yourcomputer.

NOTE: Only Checkerboard, Row-Interleave, and HDMI 1.4 Time-sequential 3D TVs are supported.

NOTE: 3D playback of photos and videos is supported only on the computer display.


Caring for the 3D glassesUsing the nose pieces

The 3D glasses come with 3 nose pieces in different sizes. One nose piece is installed at the factoryand two additional nose pieces are shipped with the glasses. Try on the glasses, and if the fit isuncomfortable, wear the glasses without a nose piece or try one of the other nose pieces.

NOTE: The 3D glasses are designed to fit over most standard prescription glasses.

▲ To add a nose piece, insert the nose piece onto the glasses. To remove a nose piece, pull thenose piece away from the glasses.

Caring for the 3D glasses 19

Replacing the batteryThe battery in the 3D glasses is installed at the factory and provides approximately 150 hours of 3Dviewing time. The glasses can remain in Standby mode for up to one year. HP recommends that youreplace the battery once a year, using a basic CR2032 battery that can be purchased anywherebatteries are sold.

WARNING! To reduce the risk of fire or explosion, replace the battery with only a CR2032 battery.

Dispose of the used battery promptly and according to local regulations. Be sure to keep the batteryaway from children.

To replace the battery:

1. Slide the battery compartment cover (1) down, and then remove the used battery (2).


2. Carefully insert the new battery (1) with the positive (+) side facing the battery compartmentcover, and then replace the battery compartment cover (2).

CAUTION: To reduce the risk of damage to the glasses, use caution when inserting thebattery.

Cleaning the 3D glassesTo remove smudges and lint, clean the 3D glasses with a soft, damp, lint-free cloth as needed. Thecloth can be dampened with mild cleaning agents that contain less than 10% alcohol.

CAUTION: To reduce the risk of permanent damage to the 3D glasses:

Do not use paper-based towels, because they can scratch the lenses.

Do not spray cleaning fluids or chemicals directly on the lenses.

Do not use ammonia-based cleaning products.

Caring for the 3D glasses 21

Handling the glassesThe 3D glasses are durable but they are sensitive to physical pressure and must be handled withcare. To avoid getting fingerprints on the lenses, handle the glasses by the frames. When you are notusing the 3D glasses, store them in the protective pouch.

CAUTION: To reduce the risk of cracking the lenses, never twist or rotate the 3D glasses.

Frequently asked questions Why can't I see 3D content

If you are watching in 3D mode and cannot see 3D content, HP recommends that you take off the 3Dglasses, and read the 3D safety information on page 12. Consult a physician if you suspect a physicalproblem seeing stereoscopic 3D.

● You may be trying to watch 3D content in 2D mode. For more information, see Viewing 2D Blu-ray Discs in 3D on page 18.

● The clear protective film on both sides of the glasses lenses (select models only) may need tobe removed.

● The battery in the 3D glasses may need to be replaced. For more information, see Replacing thebattery on page 20.

● The IR emitters on the computer display may be obstructed. For optimal transmission, keep theareas immediately around the IR emitters free from obstructions. For the location of the IRemitters, see Getting to know your computer on page 24.

● You may be sitting too far from the computer display. You should be within approximately 1.5meters (5 feet) of the display when viewing 3D content.

NOTE: This distance varies depending on your viewing angle.

What 3D formats are supported on my computer● Blu-ray Disc 3D movies

● Stereoscopic 3D games

● 3D MPEG 4 MVC files for 3D video playback

● 3D H.264 MVC and Fujifilm AVI dual-stream video file formats for 3D video playback

● 3D Fujifilm MPO for 3D photo viewing

Can I play stereoscopic 3D games on my computerYes, you can play stereo 3D games on your computer using TriDef 3D Experience Ignition GamePlayer.

▲ To access the game player, select Start > All Programs > TriDef 3D > TriDef 3D Ignition.


Can I use the 3D glasses to view a 3D movie in a movie theaterThe 3D glasses are optimized to work with this computer and integrated IR emitters. The 3D glassesare not guaranteed to work optimally in any other 3D environment.

Can I wear my 3D glasses over my prescription glassesYes. The 3D glasses are designed to fit over most prescription glasses. If you normally wear glasseswhen viewing the computer screen, keep them on and put the 3D glasses on over your eyewear. Youcan use the additional replaceable nose pieces to find a comfortable fit. See Using the HP 3D ActiveShutter Glasses on page 15 for more information.

How do I clean my 3D glassesUse a soft, damp, lint-free cloth to clean your 3D glasses. See Caring for the 3D glasses on page 19for more information.

How close do I need to be to the computer to view 3D contentThe effective range of the integrated IR emitters is approximately 1.5 meters (5 feet) from thecomputer display. This distance varies depending on your viewing angle.

Why do I see flickering when I watch 3D contentFlickering in your 3D glasses can be caused by one of the following:

● Differences in the frequencies at which the lighting in your room and 3D Cinema Technologyoperate. Resolve this issue by dimming or turning off the lights.

● Low battery in the glasses. Try replacing the battery.

Can I use the 3D glasses in bright sunlight next to a windowThe stereoscopic 3D effect works best in a darkened room.

What type of batteries do I need for the 3D glassesThe 3D glasses use a basic CR2032 battery, available anywhere batteries are sold. For moreinformation, see Replacing the battery on page 20.

Can I use my computer to watch 3D content on my external 3D TVYes, you can watch 3D content on your external 3D TV (purchased separately), by using a high-speed HDMI 1.4 cable to connect the computer to the 3D TV.

NOTE: Only Checkerboard, Row-Interleave, and HDMI 1.4 Time-sequential 3D TVs are supported.

NOTE: To watch 3D content on your external 3D TV, you must use the 3D glasses that came withyour TV, not the glasses that came with your computer.

Frequently asked questions 23

3 Getting to know your computer


● Top

● Front

● Right side

● Left side

● Display

● Bottom

Top Imagepad

Component Description

(1) Imagepad light ● Amber: The Imagepad is off.

● Off: The Imagepad is on.

(2) Imagepad on/off button Quickly double-tap this button to turn the Imagepad off or on.

24 Chapter 3 Getting to know your computer


(3) Left Imagepad button The bottom left corner of the Imagepad functions like the leftbutton on an external mouse.

(4) Imagepad zone Moves the pointer and selects or activates items on thescreen.

(5) Right Imagepad button The bottom right corner of the Imagepad functions like theright button on an external mouse.

Lights


(1) Imagepad light ● Amber: The Imagepad is off.

● Off: The Imagepad is on.

(2) Caps lock light ● White: Caps lock is on.

● Off: Caps lock is off.

(3) Power light ● White: The computer is on.

● Blinking white: The computer is in the Sleep state.

● Off: The computer is off or in Hibernation.

(4) Wireless light ● White: An integrated wireless device, such as awireless local area network (WLAN) device, isenabled.

● Amber: All wireless devices are disabled.

(5) Mute light ● Amber: Speaker sound is off.

● Off: Speaker sound is on.

Top 25

Buttons and speakers


(1) Power button ● When the computer is off, press the button to turn on the computer.

● When the computer is on, press the button briefly to initiate Sleep.

● When the computer is in the Sleep state, press the button briefly to exitSleep.

● When the computer is in Hibernation, press the button briefly to exitHibernation.

CAUTION: Pressing and holding down the power button will result in theloss of unsaved information.

If the computer has stopped responding and Windows shutdown proceduresare ineffective, press and hold the power button for at least 5 seconds to turnoff the computer.

To learn more about your power settings, select Start > Control Panel >System and Security > Power Options, or see the HP Notebook ReferenceGuide.

(2) Stereo speakers (2) Produce enhanced, Beats Audio sound.

(3) Mute button Mutes or restores speaker sound.

(4) Beats Audio button Opens Beats Audio Control Panel, which allows you to view and control theaudio and bass settings.

Beats Audio is an enhanced audio feature that provides a deep, controlledbass while maintaining a clear sound.

NOTE: You can also open Beats Audio Control Panel by selecting Start >Control Panel > Hardware and Sound > Beats Audio Control Panel.


Keys


(1) esc key Displays system information when pressed in combination with thefn key.

(2) fn key Executes the following functions:

● When the key is pressed in combination with the esc key,system information is displayed.

● When the key is pressed in combination with the b key, BeatsAudio is enabled or disabled.

(3) Windows logo key Displays the Windows Start menu.

(4) Action keys Execute frequently used system functions.

(5) b key Enables or disables Beats Audio when pressed in combination withthe fn key.

(6) Windows applications key Displays a shortcut menu for items beneath the pointer.

(7) Integrated numeric keypad Can be used like an external numeric keypad.

(8) num lock key Alternates between navigational and numeric functions of theintegrated numeric keypad.

NOTE: The keypad function that is active when the computer isturned off is reinstated when the computer is turned back on.

Top 27

Front


Stereo speakers (4) Produce enhanced, Beats Audio sound.


Right side


(1) Digital Media Slot Supports the following digital card formats:

● MultiMediaCard

● Secure Digital (SD) Memory Card

● Secure Digital High Capacity Memory Card

(2) Hard drive light ● Blinking white: The hard drive is being accessed.

● Amber: HP ProtectSmart Hard Drive Protection hastemporarily parked the hard drive.

NOTE: For information on HP ProtectSmart Hard DriveProtection, see the HP Notebook Reference Guide.

(3) Power light ● White: The computer is on.

● Blinking white: The computer is in the Sleep state.

● Off: The computer is off or in Hibernation.

(4) HDMI port Connects an optional video or audio device, such as a high-definition television, any compatible digital or audio component,or a high-speed HDMI 1.4 device.

(5) DisplayPorts (2) Connect optional digital display devices, such as high-performance monitors or projectors.

(6) USB 3.0 ports (2) Connect optional USB 1.0, USB 2.0, or USB 3.0 devices andprovide enhanced USB power performance for USB 3.0 devices.

(7) Volume dial Adjusts the speaker volume.

Rotate the dial clockwise to increase the volume or rotate the dialcounter-clockwise to decrease the volume.

(8) RJ-45 (network) jack Connects a network cable.

Right side 29


(9) AC adapter light ● White: The computer is connected to external power, andthe battery is fully charged.

● Amber: The computer is connected to external power, andthe battery is charging.

● Blinking amber: The computer is connected to externalpower, and there is a battery error or the battery hasreached a low or critical battery level.

● Off: The computer is running on battery power.

(10) Power connector Connects an AC adapter.


Left side


(1) Optical drive Reads and writes to an optical disc.

(2) USB 3.0 ports (2) Connect optional USB 1.0, USB 2.0, or USB 3.0 devices andprovide enhanced USB power performance for USB 3.0devices.

(3) Audio-in (microphone) jack Connects an optional computer headset microphone, stereoarray microphone, or monaural microphone.

(4) Audio-out (headphone) jacks (2) Produce sound when connected to optional powered stereospeakers, headphones, ear buds, a headset, or televisionaudio.

WARNING! To reduce the risk of personal injury, adjust thevolume before putting on headphones, earbuds, or a headset.For additional safety information, see the Regulatory, Safety,and Environmental Notices.

NOTE: When a device is connected to either jack, thecomputer speakers are disabled.

(5) Security cable slot Attaches an optional security cable to the computer.

NOTE: The security cable is designed to act as a deterrent,but it may not prevent the computer from being mishandled orstolen.

Left side 31

Display


(1) WLAN antennas (2)* Send and receive networking signals using up to 2 integrated antennas to alocal wireless router or hub.

(2) IR emitters (2)* Wirelessly synchronize the 3D glasses with the computer display.

(3) Proximity sensors (2) Detect your presence in front of the computer and turn on the radiancebacklight keyboard feature.

(4) Internal microphones (2) Record audio using the integrated microphones by specific programs. Themicrophones will automatically improve the audio to reduce ambient noiseand provide echo cancellation.

(5) Webcam light Turns on when the webcam is active.

(6) HP TrueVision HD Webcam Records video and captures still photographs.

To access the webcam, select Start > All Programs > CyberLink >CyberLink YouCam.

(7) Internal display switch Turns off the display and initiates Sleep if the display is closed while thepower is on.

NOTE: The internal display switch is not visible from the outside of thecomputer.

*The antennas and IR emitters are not visible from the outside of the computer. For optimal transmission, keep the areasimmediately around the antennas and IR emitters free from obstructions. To see wireless regulatory notices, see the sectionof the Regulatory, Safety, and Environmental Notices that applies to your country or region. These notices are located inHelp and Support.


Bottom


(1) Hard drive cover Provides access to the hard drives.

(2) Vents (5) Enable airflow to cool internal components.

NOTE: The computer fan starts up automatically to cool internalcomponents and prevent overheating. It is normal for the internal fanto cycle on and off during routine operation.

(3) Release latch Releases the hard drive cover.

(4) Service access door Provides access to the memory module slots.

(5) HP Triple Bass Reflex Subwoofer Provides superior bass sound.

Bottom 33

4 Networking

● Using an Internet service provider (ISP)

● Connecting to a wireless network

NOTE: Internet hardware and software features vary depending on computer model and yourlocation.

Your computer may support one or both of the following types of Internet access:

● Wireless—For mobile Internet access, you can use a wireless connection. See Connecting to anexisting WLAN on page 36 or Setting up a new WLAN network on page 36.

● Wired—You can access the Internet by connecting to a wired network. For information onconnecting to a wired network, see the HP Notebook Reference Guide.

34 Chapter 4 Networking

Using an Internet service provider (ISP)Before you can connect to the Internet, you must establish an ISP account. Contact a local ISP topurchase Internet service and a modem. The ISP helps to set up the modem, install a network cableto connect your wireless computer to the modem, and test the Internet service.

NOTE: Your ISP will give you a user ID and password to access the Internet. Record thisinformation and store it in a safe place.

The following features help you set up a new Internet account or configure the computer to use anexisting account:

● ISP-provided icons (available in some locations)—These icons are individually displayed onthe Windows desktop. To set up a new Internet account or configure the computer to use anexisting account, double-click an icon, and then follow the on-screen instructions.

● Windows Connect to the Internet Wizard—You can use the Windows Connect to the InternetWizard to connect to the Internet in any of the following situations:

◦ You already have an account with an ISP.

◦ You do not have an Internet account and want to select an ISP from the list provided withinthe wizard. (The list of ISP providers is not available in all regions.)

◦ You have selected an unlisted ISP, and the ISP has provided you with information such asa specific IP address and POP3 and SMTP settings.

To access the Windows Connect to the Internet Wizard and instructions for using it, selectStart > Control Panel > Network and Internet > Network and Sharing Center > Set up anew connection or network.

NOTE: If you are prompted within the wizard to choose between enabling or disablingWindows Firewall, choose to enable the firewall.

Connecting to a wireless networkWireless technology transfers data across radio waves instead of wires. Your computer may beequipped with one or more of the following wireless devices:

● Wireless local area network (WLAN) device

● HP Mobile Broadband Module, a wireless wide area network (WWAN) device

● Bluetooth® device

For more information on wireless technology and connecting to a wireless network, see theHP Notebook Reference Guide and information and Web site links provided in Help and Support.

Using an Internet service provider (ISP) 35

Connecting to an existing WLAN1. Turn on the computer.

2. Be sure that the WLAN device is on.

3. Click the network icon in the notification area, at the far right of the taskbar.

4. Select a network to connect to.

5. Click Connect.

6. If required, enter the security key.

Setting up a new WLAN networkRequired equipment:

● A broadband modem (either DSL or cable) (1) and high-speed Internet service purchased froman Internet service provider (ISP)

● A wireless router (purchased separately) (2)

● Your new wireless computer (3)

NOTE: Some modems have a built-in wireless router. Check with your ISP to determine what typeof modem you have.

The illustration shows an example of a completed WLAN network installation that is connected to theInternet. As your network grows, additional wireless and wired computers can be connected to thenetwork to access the Internet.

36 Chapter 4 Networking

Configuring a wireless routerFor help in setting up a WLAN, see the information provided by your router manufacturer or your ISP.

The Windows operating system also provides tools to help you set up a new wireless network. To usethe Windows tools to set up your network, select Start > Control Panel > Network and Internet >Network and Sharing Center > Set up a new connection or network > Set up a new network.Then follow the on-screen instructions.

NOTE: It is recommended that you initially connect your new wireless computer to the router byusing the network cable provided with the router. When the computer successfully connects to theInternet, you can disconnect the cable, and then access the Internet through your wireless network.

Protecting your WLANWhen you set up a WLAN or access an existing WLAN, always turn on security features to protectyour network from unauthorized access.

For information on protecting your WLAN, see the HP Notebook Reference Guide.

Connecting to a wireless network 37

5 Keyboard and pointing devices


● Using the keyboard

● Using pointing devices

Using the keyboardUsing the action keys

Action keys are used for performing customized actions that are assigned to specific keys at the topof the keyboard.

The icons on the f1 through f8, f10, and f12 keys represent the action key functions. To activate afunction, press and hold the key.

You can disable the action key feature and revert back to standard settings. Using standard settings,you press the fn key and one of the function keys to activate the assigned function. For instructionson disabling the action key feature, see the “Setup Utility (BIOS) and System Diagnostics” chapter inthe HP Notebook Reference Guide.

CAUTION: Use extreme care when making changes. Errors can prevent the computer fromoperating properly.

Icon Key Description

f1 Opens Help and Support, which provides information about your Windows operating system andcomputer, answers to questions and tutorials, and updates to your computer.

Help and Support also provides automated troubleshooting and links to support specialists.

f2 Decreases the screen brightness level.

f3 Increases the screen brightness level.

38 Chapter 5 Keyboard and pointing devices

Icon Key Description

f4 Presents the following choices to switch the screen image among display devices connected to thecomputer:

● Computer only—Turns off any external displays and shows the image only on only the computerdisplay.

● Duplicate—Clones the image on the computer display onto an external display that is connectedto the computer.

● Extend—Extends the screen image across the computer display and all connected externaldisplays.

● Projector only—Turns off the computer display and extends the screen image across allconnected external displays.

f5 Turns the radiance backlight keyboard feature off or on.

NOTE: To conserve battery power, turn off this feature. To switch between low, medium, or highbrightness levels, press and hold the keyboard backlight action key (f5) in combination with either theup or down arrow key.

f6 Plays the previous track of an audio CD or the previous section of a DVD or a BD.

f7 Plays, pauses, or resumes an audio CD, a DVD, or a BD.

f8 Plays the next track of an audio CD or the next section of a DVD or a BD.

f10 Ejects a disc from the optical drive.

f12 Turns off or on all wireless features, including wireless networking, wireless display, and wirelessaudio.

NOTE: This key does not establish a wireless connection. To establish a wireless connection, awireless network must be set up.

Using the keyboard 39

Using the integrated numeric keypad


(1) num lock key Alternates between the navigational functions and the numericfunctions on the integrated numeric keypad.

NOTE: The keypad function that is active when the computer isturned off is reinstated when the computer is turned back on.

(2) Integrated numeric keypad Can be used like an external numeric keypad.


Using pointing devicesNOTE: In addition to the pointing devices included with your computer, you can use an externalUSB mouse (purchased separately) by connecting it to one of the USB ports on the computer.

Setting pointing device preferencesUse Mouse Properties in Windows to customize settings for pointing devices, such as buttonconfiguration, click speed, and pointer options.

To access Mouse Properties, select Start > Devices and Printers. Then right-click the devicerepresenting your computer, and select Mouse settings.

Using pointing devices 41

Using the ImagepadThe advanced Imagepad is a high-precision gesture-friendly mouse alternative. To move the pointer,slide one finger across the Imagepad in the direction you want the pointer to go. Use the left and rightImagepad buttons like the corresponding buttons on an external mouse.

Turning the Imagepad off or onTo turn the Imagepad off or on, quickly double-tap the Imagepad on/off button.

NOTE: The Imagepad light is off when the Imagepad is on.

The Imagepad light and on-screen display icons indicate the Imagepad status.

Imagepad light Icon Description

Amber Indicates that the Imagepad is off.

Off Indicates that the Imagepad is on.


NavigatingTo move the pointer, slide one finger across the Imagepad in the direction you want the pointer to go.

SelectingUse the left and right Imagepad buttons like the corresponding buttons on an external mouse.

Using Imagepad gesturesThe Imagepad supports a variety of gestures. To use Imagepad gestures, place two fingers on theImagepad at the same time.

NOTE: Imagepad gestures are not supported in all computer programs.

To view the demonstration of a gesture:

1. Select Start > Control Panel > Hardware and Sound > Synaptics ClickPad.

2. Click a gesture to activate the demonstration.


To turn the gestures on or off:

1. Select Start > Control Panel > Hardware and Sound > Synaptics ClickPad.

2. Select the check box next to the gesture that you want to turn on or off.

3. Click Apply, and then click OK.

Scrolling

Scrolling is useful for moving up, down, or sideways on a page or image. To scroll, place two fingersslightly apart on the Imagepad, and then drag them across the Imagepad in an up, down, left, or rightmotion.

NOTE: Scrolling speed is controlled by finger speed.

NOTE: Scrolling is enabled at the factory.

Pinching/Zooming

Pinching allows you to zoom in or out on images or text.

● Zoom in by placing two fingers together on the Imagepad, and then moving them apart.

● Zoom out by placing two fingers apart on the Imagepad, and then moving them together.

NOTE: Pinching/zooming is enabled at the factory.


Rotating

Rotating allows you to rotate items such as photos. Place two separated fingers on the Imagepad,and then rotate your fingers in an arc while maintaining uniform finger separation. An arcing motion tothe left rotates the object to the left; an arcing motion to the right rotates the object to the right.

NOTE: Rotating is enabled at the factory.

Flicking

Flicking allows you to quickly perform the following functions:

● Browse the Internet.

● Scroll through photos in a photo viewer.

● Navigate through screens.

● Scroll through documents.

● Enter or exit the slide show mode in your photo viewer.

To flick, use three fingers to touch the Imagepad in a light, quick flicking motion up, down, left, orright.

NOTE: Three-finger flicking is enabled at the factory.


6 Maintenance


● Using a factory-sealed battery

● Replacing or upgrading the hard drives

● Adding or replacing memory modules

Using a factory-sealed batteryIMPORTANT: Do not attempt to replace your computer battery, which is preinstalled and sealed atthe factory. A broken battery seal voids your warranty.

Your computer has an internal rechargeable battery that can be replaced only by an authorizedservice provider. For steps to keep your battery in good condition, see “Using Battery Power” in theHP Notebook Reference Guide. To access this guide, select Start > Help and Support > UserGuides. To monitor the status of your battery, or if the battery is no longer holding a charge, runBattery Check in Help and Support. Contact customer support if the computer battery needs to bereplaced.

46 Chapter 6 Maintenance

Replacing or upgrading the hard drivesCAUTION: To reduce the risk of information loss or an unresponsive system:

Shut down the computer before removing a hard drive from the hard drive bay.

If you are not sure whether the computer is off, in the Sleep state, or in Hibernation, press the powerbutton, and then shut down the computer through the operating system.

NOTE: Some computer models can support up to three drives—two hard drives and one solid-statedrive. To determine the number and type of drives installed in your computer, click Start, right-clickComputer, click Manage, and then click Disk Management.

NOTE: When replacing a hard drive, make sure that you save the hard drive bracket and cover.You may need these parts to install the new hard drive.

Removing and installing the primary hard drive

Removing the primary hard drive1. Save your work and shut down the computer.

2. Disconnect all external devices connected to the computer.

3. Remove external power from the computer.

4. Slide the release latch (1), and then remove the hard drive cover (2).

5. Remove the service access door.

a. Remove the 6 service access door screws (1).

Replacing or upgrading the hard drives 47

b. Remove the door (2).

6. Disconnect the battery cable from the computer.

7. Disconnect the hard drive cable (1) from the computer.

8. Pull back the plastic cover (2).


9. Remove the 4 hard drive screws (3), and then lift the hard drive (4) out of the hard drive bay.

Installing the primary hard drive1. Insert the hard drive (1) into the hard drive bay, and then replace the 4 hard drive screws (2).

2. Connect the hard drive cable (3) to the computer.


3. Replace the plastic cover (4).

4. Connect the battery cable to the computer.

5. Align the screw holes in the service access door with the holes in the computer, and then lowerthe door (1) onto the computer.


6. Replace the 6 service access door screws (2).

7. Align the tabs on the hard drive cover with the notches on the computer, and then slide the coverinto the notches. The release latch automatically locks the cover into place.

8. Reconnect external power and external devices.

9. Turn on the computer.


Removing and inserting the secondary hard drive

Removing the secondary hard drive1. Save your work and shut down the computer.









7. Disconnect the hard drive cable (1) from the computer.

8. Pull back the plastic cover (2).


9. Remove the 4 hard drive screws (3), and then lift the hard drive (4) out of the hard drive bay.

Installing the secondary hard drive1. Insert the hard drive (1) into the hard drive bay, and then replace the 4 hard drive screws (2).

2. Connect the hard drive cable (3) to the computer.


3. Replace the plastic cover (4) over the hard drive.





7. Align the tabs on the hard drive cover with the notches on the computer, and then slide the coverinto the notches. The release latch automatically locks the cover into place.




Adding or replacing memory modulesThe computer has two memory module slots. They are located under the service access door on thebottom of the computer. The memory capacity of the computer can be upgraded by adding a memorymodule or replacing a memory module in one of the memory module slots.

WARNING! To reduce the risk of electric shock and damage to the equipment, unplug the powercord before installing a memory module.

CAUTION: Electrostatic discharge (ESD) can damage electronic components. Before beginningany procedure, ensure that you are discharged of static electricity by touching a grounded metalobject.

NOTE: To use a dual-channel configuration when adding a second memory module, be sure thatboth memory modules are identical.

To add or replace a memory module:

CAUTION: To reduce the risk of information loss or an unresponsive system:

Shut down the computer before removing a memory module from the computer. Do not remove amemory module while the computer is on, in the Sleep state, or in Hibernation.

If you are not sure whether the computer is off, in the Sleep state, or in Hibernation, press the powerbutton, and then shut down the computer through the operating system.

1. Save your work and shut down the computer.






Adding or replacing memory modules 57



7. If you are replacing a memory module, remove the existing memory module.

a. Pull away the retention clips (1) on each side of the memory module.

The memory module tilts up.


b. Grasp the edge of the memory module (2), and then gently pull the module out of thememory module slot.

CAUTION: To reduce the risk of damage to the memory module, hold the memorymodule by the edges only. Do not touch the components on the memory module. Toprotect a memory module after removal, place it in an electrostatic-safe container.

8. Insert a new memory module.

CAUTION: To reduce the risk of damage to the memory module, hold the memory module bythe edges only. Do not touch the components on the memory module, and do not bend thememory module.

a. Align the notched edge (1) of the memory module with the tab in the memory module slot.

b. Position the memory module at a 45-degree angle from the surface of the memory modulecompartment, and then press the module (2) into the slot until the module is seated.


c. Gently press the memory module (3) down, applying pressure to both the left and rightedges of the memory module, until the retention clips snap into place.





12. Align the tabs on the hard drive cover with the notches on the computer, and then slide the coverinto place. The release latch automatically locks the cover into place.




7 Backup and recovery

● Restore

● Creating recovery media

● Performing a system restore

● Backing up and recovering your information

Your computer includes tools provided by the operating system and HP to help you safeguard yourinformation and restore it if necessary.

This chapter provides information about the following topics:

● Creating a set of recovery discs or a recovery flash drive (HP Recovery Manager softwarefeature)

● Performing a system restore (from the recovery partition, recovery discs, or a recovery flashdrive)

● Backing up your information

● Recovering a program or driver

62 Chapter 7 Backup and recovery

RestoreIn the event of hard drive failure, to restore your system to its factory image you must use a set ofrecovery discs or a recovery flash drive that you have created using HP Recovery Manager. HPrecommends that you use HP Recovery Manager immediately after software setup to create either aset of recovery discs or a recovery flash drive.

If you need to restore your system for some other reason than hard drive failure, you can use the HPRecovery partition (select models only), without the need for recovery discs or a recovery flash drive.To check for the presence of a recovery partition, click Start, right-click Computer, click Manage,and then click Disk Management. If the recovery partition is present, a Recovery drive is listed in thewindow.

CAUTION: HP Recovery Manager (partition or discs/flash drive) restores only the software that wasinstalled at the factory. Software not provided with this computer must be reinstalled manually.

NOTE: Recovery discs have been included if your computer does not have a recovery partition.

Restore 63

Creating recovery mediaHP recommends that you create either a set of recovery discs or a recovery flash drive to be sure thatyou can restore your computer to its original factory state if the hard drive fails, or if for any reasonyou cannot restore using the recovery partition tools. Create these discs or the flash drive after settingup the computer for the first time.

NOTE: HP Recovery Manager allows the creation of only one set of recovery discs or one recoveryflash drive. Handle these discs or the flash drive carefully and keep them in a safe place.

NOTE: If your computer does not include an integrated optical drive, you can use an optionalexternal optical drive (purchased separately) to create recovery discs, or you can purchase recoverydiscs for your computer from the HP website. If you use an external optical drive, it must beconnected directly to a USB port on the computer, not to a USB port on an external device, such as aUSB hub.

Guidelines:

● Purchase high-quality DVD-R, DVD+R, DVD-R DL, or DVD+R DL discs.

NOTE: Read-write discs, such as CD-RW, DVD±RW, double-layer DVD±RW, and BD-RE(rewritable Blu-ray) discs, are not compatible with the HP Recovery Manager software.

● The computer must be connected to AC power during this process.

● Only one set of recovery discs or one recovery flash drive can be created per computer.

NOTE: If you are creating recovery discs, number each disc before inserting it into the opticaldrive.

● If necessary, you can exit the program before you have finished creating the recovery discs orrecovery flash drive. The next time you open HP Recovery Manager, you will be prompted tocontinue the backup creation process.

To create a set of recovery discs or a recovery flash drive:

1. Select Start > All Programs > HP > HP Recovery Manager > HP Recovery Media Creation.

2. Follow the on-screen instructions.

Performing a system restoreHP Recovery Manager software allows you to repair or restore the computer to its original factorystate. HP Recovery Manager works from recovery discs or a recovery flash drive, or from a dedicatedrecovery partition (select models only) on the hard drive.

NOTE: A system restore must be performed if the computer hard drive has failed or if all attempts tocorrect any functional computer issues fail. A system restore should be used only as a final attempt tocorrect computer issues.


Note the following when performing a system restore:

● You can restore the system only if you have previously backed it up. HP recommends that assoon as you set up the computer you use HP Recovery Manager to create either a set ofrecovery discs or a recovery flash drive.

● Windows has its own built-in repair features, such as System Restore. If you have not alreadytried these features, try them before using HP Recovery Manager.

● HP Recovery Manager restores only software that was installed at the factory. Software notprovided with this computer must be downloaded from the manufacturer's website or reinstalledfrom the disc provided by the manufacturer.

Restoring using the dedicated recovery partition (select models only)When using the dedicated recovery partition, you can back up pictures, music and other audio, videosand movies, recorded TV shows, documents, spreadsheets and presentations, email, and Internetfavorites and settings during this process.

To restore the computer from the recovery partition, follow these steps:

1. Access HP Recovery Manager in either of the following ways:

● Select Start > All Programs > HP > HP Recovery Manager > HP Recovery Manager.

– or –

● Turn on or restart the computer, and then press esc while the “Press the ESC key forStartup Menu” message is displayed at the bottom of the screen. Then, press f11 while the“F11 (System Recovery)” message is displayed on the screen.

2. Click System Recovery in the HP Recovery Manager window.


Restoring using the recovery media1. If possible, back up all personal files.

2. Insert the first recovery disc into the optical drive on your computer or an optional externaloptical drive, and then restart the computer.

– or –

Insert the recovery flash drive into a USB port on your computer, and then restart the computer.

3. Press f9 at system bootup.

4. Select the optical drive or the flash drive.


Performing a system restore 65

Changing the computer boot orderTo change the boot order for recovery discs:

1. Restart the computer.

2. Press esc while the computer is restarting, and then press f9 for boot options.

3. Select Internal CD/DVD ROM Drive from the boot options window.

To change the boot order for a recovery flash drive:

1. Insert the flash drive into a USB port.

2. Restart the computer.

3. Press esc while the computer is restarting, and then press f9 for boot options.

4. Select the flash drive from the boot options window.

Backing up and recovering your informationIt is very important to back up your files and keep any new software in a safe place. As you add newsoftware and data files, continue to create backups on a regular basis.

How completely you are able to recover your system depends on how recent your backup is.

NOTE: A recovery from your most recent backup should be performed if the computer is attackedby a virus or if any major system components fail. In order to correct computer issues, attempt arecovery before you attempt a system restore.

You can back up your information to an optional external hard drive, a network drive, or discs. Backup your system at the following times:

● At regularly scheduled times

TIP: Set reminders to back up your information periodically.

● Before the computer is repaired or restored

● Before you add or modify hardware or software

Guidelines:

● Create system restore points using the Windows® System Restore feature, and periodicallycopy them to an optical disc or an external hard drive. For more information about using systemrestore points, see Using Windows system restore points on page 67.

● Store personal files in the Documents library and back up this folder periodically.

● Save customized settings in a window, toolbar, or menu bar by taking a screen shot of yoursettings. The screen shot can be a time-saver if you have to reenter your preferences.


To create a screen shot:

1. Display the screen you want to save.

2. Copy the screen image.

To copy only the active window, press alt+prt sc.

To copy the entire screen, press prt sc.

3. Open a word-processing document, and then select Edit > Paste. The screen image is added tothe document.

4. Save and print the document.

Using Windows Backup and RestoreGuidelines:

● Connect the computer to AC power before you start the backup process.

● Allow enough time to complete the backup process. Depending on file sizes, it may take over anhour.

To create a backup:

1. Select Start > Control Panel > System and Security > Backup and Restore.

2. Follow the on-screen instructions to schedule and create a backup.

NOTE: Windows® includes the User Account Control feature to improve the security of thecomputer. You may be prompted for your permission or password for tasks such as installingsoftware, running utilities, or changing Windows settings. For more information, see Help andSupport.

Using Windows system restore pointsA system restore point allows you to save and name a snapshot of your hard drive at a specific pointin time. You can then recover back to that point if you want to reverse subsequent changes.

NOTE: Recovering to an earlier restore point does not affect data files saved or e-mails createdsince the last restore point.

You also can create additional restore points to provide increased protection for your files andsettings.

When to create restore points● Before you add or modify software or hardware

● Periodically, whenever the computer is functioning optimally

Backing up and recovering your information 67

Create a system restore point1. Select Start > Control Panel > System and Security > System.

2. In the left pane, click System protection.

3. Click the System Protection tab.

4. Click Create.


Restore to a previous date and timeTo revert to a restore point (created at a previous date and time), when the computer was functioningoptimally, follow these steps:

1. Select Start > Control Panel > System and Security > System.

2. In the left pane, click System protection.

3. Click the System Protection tab.

4. Click System Restore.


NOTE: If you revert to a restore point and then change your mind, you can reverse the restoration.


8 Customer support


● Contacting customer support

● Labels

Contacting customer supportIf the information provided in this guide, in the HP Notebook Reference Guide, or in Help and Supportdoes not address your questions, you can contact HP Customer Support. For U.S. product support,go to http://www.hp.com/go/contactHP. For worldwide product support, go to http://welcome.hp.com/country/us/en/wwcontact_us.html.

Here you can:

● Chat online with an HP technician.

NOTE: When technical support chat is not available in a particular language, it is available inEnglish.

● E-mail HP Customer Support.

● Find HP Customer Support worldwide telephone numbers.

● Locate an HP service center.

Contacting customer support 69




LabelsThe labels affixed to the computer provide information you may need when you troubleshoot systemproblems or travel internationally with the computer.

● Serial number label—Provides important information, including the following:

Component

(1) Product name

(2) Serial number (s/n)

(3) Part number/Product number (p/n)

(4) Warranty period

(5) Model description

Have this information available when you contact technical support. The serial number label islocated on the bottom of the computer, inside the battery bay, or in another easily accessiblelocation.

● Microsoft® Certificate of Authenticity—Contains the Windows Product Key. You may need theProduct Key to update or troubleshoot the operating system. The Microsoft Certificate ofAuthenticity is located on the bottom of the computer.

● Regulatory label—Provides regulatory information about the computer. The regulatory label islocated on the bottom of the computer, inside the battery bay, or in another easily accessiblelocation.

● Wireless certification label or labels (select models only)—Provide information about optionalwireless devices and the approval markings of some of the countries or regions in which thedevices have been approved for use. If your computer model includes one or more wirelessdevices, one or more certification labels are included with your computer. You may need thisinformation when traveling internationally. Wireless certification labels are located on the bottomof the computer, inside the battery bay, or in another easily accessible location.

70 Chapter 8 Customer support

9 Specifications

● Input power

● Operating environment

Input powerThe power information in this section may be helpful if you plan to travel internationally with thecomputer.

The computer operates on DC power, which can be supplied by an AC or a DC power source. TheAC power source must be rated at 100–240 V, 50–60 Hz. Although the computer can be poweredfrom a standalone DC power source, it should be powered only with an AC adapter or a DC powersource supplied and approved by HP for use with this computer.

The computer can operate on DC power within the following specifications.

Input power Rating

Operating voltage and current 19.5 V dc @ 6.15 A –120 W

DC plug of external HP power supply

NOTE: This product is designed for IT power systems in Norway with phase-to-phase voltage notexceeding 240 V rms.

NOTE: The computer operating voltage and current can be found on the regulatory label.

Input power 71

Operating environmentFactor Metric U.S.

Temperature

Operating 5°C to 35°C 41°F to 95°F

Nonoperating -20°C to 60°C -4°F to 140°F

Relative humidity (noncondensing)

Operating 10% to 90% 10% to 90%

Nonoperating 5% to 95% 5% to 95%

Maximum altitude (unpressurized)

Operating -15 m to 3,048 m -50 ft to 10,000 ft

Nonoperating -15 m to 12,192 m -50 ft to 40,000 ft

72 Chapter 9 Specifications

Index

Symbols/Numerics3D Active Shutter Glasses

battery compartment 15care 19cleaning 21handling 22identifying 15nose pieces 15, 19replacing the battery 20turning on and off 16using 15

3D Cinema Technology 73D games 22effective range 23flickering 23frequently asked questions 22safety information 12using 16watching content 17

3D games, playing 18

AAC adapter light 30action keys

Help and Support 38identifying 27optical drive eject 39radiance backlight keyboard

39screen brightness 38switching screen image 39using 38wireless 39

AMD Catalyst Control Center 9AMD Eyefinity 8audio-in (microphone) jack 31audio-out (headpone) jack 31

Bbacking up

customized window, toolbar,and menu bar settings 66

personal files 66battery, replacing 46bays, hard drive 33, 70Beats Audio 3, 26Beats Audio button 3Beats Audio Control Panel 3Beats Audio hot key 4Bluetooth label 70buttons 26

Beats Audio 26Imagepad on/off 24left Imagepad 25mute 26right Imagepad 25

Ccaps lock light, identifying 25Certificate of Authenticity label 70components

bottom 33display 32front 28left-side 31right-side 29top 24

connector, power 30CoolSense 7CyberLink PowerDVD 14, 17

DDC plug of external HP power

supply 71dial, volume 29Digital Media Slot, identifying 29display image, switching 39

DisplayPort, identifying 29drives, hard 49, 54

Eesc key, identifying 27Eyefinity 8

Ff11 65flicking Imagepad gesture 45fn key, identifying 27

Ggames, 3D 18graphics modes, switching 7

Hhard drive

installing 49, 54removing 47, 52

hard drive bay 70hard drive cover, identifying 33hard drive light 29HDMI port, identifying 29headphone jack 31Help and Support key 38HP Recovery Manager 64HP Triple Bass Reflex

Subwoofer 33HP TrueVision HD Webcam 32HP Wireless Audio Manager 5

IImagepad

buttons 25identifying 24navigating 43selecting 43using 42

Index 73

Imagepad gesturesflicking 45pinching 44rotating 45scrolling 44zooming 44

Imagepad light 24, 25Imagepad on/off button 24Imagepad zone, identifying 25input power 71integrated numeric keypad,

identifying 27, 40integrated webcam light,

identifying 32Intel Smart Connect Technology

6Intel Wireless Display 7Intel Wireless Music 7internal display switch,

identifying 32internal microphones, identifying

32Internet connection setup 36IR emitters, identifying 32ISP, using 35

Jjacks

headphone 31microphone 31RJ-45 (network) 29

Kkeyboard backlight action key 39keypad, integrated 27, 40keys

action 27esc 27fn 27num lock 27Windows applications 27Windows logo 27

Llabels

Bluetooth 70Microsoft Certificate of

Authenticity 70regulatory 70serial number 70

wireless certification 70WLAN 70

latch, release 33lights

AC adapter 30caps lock 25hard drive 29Imagepad 24, 25mute 25power 25, 29webcam 32wireless 25

Mmemory module

inserting 59removing 58replacing 57

memory module compartment,identifying 33

microphone jack 31Microsoft Certificate of Authenticity

label 70mouse, external

setting preferences 41mute button, identifying 26mute light, identifying 25

Nnetwork jack, identifying 29nose pieces

identifying 15using 19

num lock key 27

Ooperating environment 72operating system

Microsoft Certificate ofAuthenticity label 70

Product Key 70operating voltage and current 71optical drive eject key,

identifying 39optical drive, identifying 31

Pphotosensitive epileptic seizures

12pinching Imagepad gesture 44

pointing devices, settingpreferences 41

portsHDMI 29USB 3.0 29, 31

power button, identifying 26power connector, identifying 30power lights, identifying 25, 29Product Key 70product name and number,

computer 70proximity sensor 32proximity sensors 6

Rradiance backlight keyboard 6recovering using the dedicated

recovery partition 65recovering using the recovery

discs 65recovery discs 64regulatory information

regulatory label 70wireless certification labels 70

release latch 33restore points 67restore, system

performing 64using recovery discs 65using the dedicated recovery

partition 65RJ-45 (network) jack, identifying

29rotating Imagepad gesture 45

Ssafety information, 3D 12screen brightness keys 38screen image, switching 39scrolling Imagepad gesture 44security cable slot, identifying 31serial number label 70serial number, computer 70service access door

identifying 33removing 58

setup of WLAN 36single large surface 8

74 Index

slotsDigital Media Slot 29security cable 31

speaker, stereo, identifying 26speakers, stereo, identifying 28stereoscopic vision 13subwoofer, identifying 33supported discs 64switchable graphics 7system recovery

performing 64using recovery discs 65using the dedicated recovery

partition 65system restore points 67

Ttraveling with the computer 70TriDef 3D Experience Ignition

Game Player 18troubleshooting, 3D

3D games 22cannot see 3D content 22flickering 23general 22supported 3D formats 22

UUSB 3.0 port, identifying 29, 31using system restore points 67

Vvents, identifying 33volume dial, identifying 2, 29

Wwebcam light, identifying 32webcam, identifying 32Windows applications key,

identifying 27Windows logo key, identifying 27Wireless Audio 5wireless certification label 70wireless key, identifying 39wireless light 25wireless network (WLAN)

connecting 36equipment needed 36protecting 37

wireless network, connecting 35wireless router, configuring 37

wireless setup 36WLAN

connecting 36equipment needed 36protecting 37

WLAN antennas, identifying 32WLAN device 70WLAN label 70

Zzooming Imagepad gesture 44

Index 75

Date post:	03-Feb-2022
Category:	Documents
Upload:	others
View:	1 times
Download:	0 times