GF Piping Systems GF Central Plastics 2016 Fabricated Fittings … · 2020-08-03 · GF Piping...

GF Central Plastics2016 Fabricated Fittings Catalog

GF Piping Systems

Also Available:

• Large Diameter Pre-Fab Headers

• Tanks

• Spools

• Custom Assemblies

• Design Assistance

• Field Support

2 GF Central Plastics - 2016 Fabricated Fittings Catalog


Table of Contents

Elbows 4

Tees 16

Wyes 22

Crosses 25

Reducer Bushings 27

Branch Saddles 29

End Caps 32

Water-Stops (Thrust-Isolators, Wall-Pipes, Anchor Rings) 34

Flange Adapters 36

Stub Ends 45

Butterfly Valve Spacers 51

Blind Flanges 52

Flange Backup Rings 53


Fabricated Elbows

IPS 3-Segment 90 Elbow (1/4 Bend)SDR 7 SDR 9

Size [inch] Part No.

R [inch]

X [inch]

E [inch]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

4 6.8 10.9 6.0 220 7 160 6

6 10.0 13.2 6.0 220 16 160 138 10.7 14.6 6.5 220 29 160 2310 13.5 16.6 6.5 220 51 160 4212 16.0 20.0 8.0 220 84 160 6814 14.5 19.4 8.0 220 99 160 8016 16.8 21.2 8.0 220 138 160 11218 18.4 22.5 8.0 220 184 160 15020 20.4 24.1 8.0 220 241 160 19622 22.4 25.7 8.0 220 308 160 25124 24.5 27.3 8.0 220 394 160 32026 26.5 30.9 10.0 160 42128 28.5 32.5 10.0 160 50930 30.5 34.1 10.032 38.0 38.9 10.034 41.0 41.0 10.036 43.0 42.6 10.042 50.0 54.0 16.048 58.0 59.9 16.054 64.0 64.7 16.0

Size [inch]

SDR 11 SDR 17 SDR 21 SDR 26 SDR 32.5WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

4 130 5 85 56 130 11 85 118 130 20 85 1410 130 34 85 2412 130 57 85 3914 130 66 85 4516 130 93 85 6318 130 126 85 8520 130 162 85 11122 130 209 85 14124 130 267 85 18126 130 354 85 23928 130 427 85 28330 130 510 85 34532 130 738 85 49634 130 871 85 58536 130 1019 85 68642 85 10 65 85648 65 1208 50 98454 50 1401 45 1126




R [inch]

X [inch]

E [inch]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

2 12.7 14.4 4.0 250 2 200 2

3 13.2 15.0 4.0 250 5 200 44 13.7 15.5 4.0 250 9 200 86 14.7 18.5 6.0 250 22 200 188 16.0 20.2 6.5 250 40 200 3210 17.0 21.2 6.5 250 64 200 5312 19.1 24.6 8.0 250 103 200 8414 21.0 26.2 8.0 250 132 200 10616 24.0 28.8 8.0 250 185 200 15118 27.0 31.4 8.0 250 254 200 20720 30.0 34.0 8.0 250 335 200 27022 33.0 36.6 8.0 250 430 200 34724 36.0 39.2 8.0 250 538 200 43726 48.0 51.0 10.0 200 51728 49.0 52.0 10.0 200 69930 52.0 54.6 10.032 54.0 56.4 10.034 55.0 57.4 10.036 58.0 60.0 10.042 63.0 70.7 16.048 72.0 78.4 16.0

54 81.0 86.3 16.0

Size [inch]


Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

2 160 1.5 105 1.53 160 4 105 44 160 7 105 76 160 15 105 158 160 27 105 19

10 160 43 105 3012 160 72 105 4614 160 88 105 6016 160 125 105 8418 160 174 105 11820 160 225 105 15322 160 292 105 19624 160 364 105 24726 160 485 105 32828 160 587 105 39030 160 714 105 48332 160 847 105 57034 160 996 105 66836 160 1176 105 79242 105 1215 80 99048 80 1402 65 114054 65 1788 50 1436


IPS 3-Segment 90 Elbow (1/4 Bend)

• Reinforced • Fully Pressure Rated with Full Flow ID

SDR 7 SDR 9 SDR 11 SDR 17 SDR 21


R [inch]

X [inch]

E [inch]

WPR [psi]

WPR [psi]

WPR [psi]

WPR [psi]

WPR [psi]

4 10.0 19.2 6.0 335 250 200 130

6 10.7 20.6 6.0 335 250 200 1308 13.5 23.1 6.5 335 250 200 13010 16.0 26.5 6.5 335 250 200 13012 14.5 27.4 8.0 335 250 200 13014 16.8 29.2 8.0 335 250 200 130

16 18.4 30.5 8.0 335 250 200 13018 20.4 32.1 8.0 335 250 200 13020 22.4 33.7 8.0 335 250 200 13022 24.5 35.3 8.0 335 250 200 13024 26.5 38.9 8.0 335 250 200 13030 38.4 48.9 10.0 250 200 130

36 45.6 64.6 10.0 200 130 100



SDR 7 SDR 9 SDR 11 SDR 17

Size[inch] Part No.

R [inch]

X [inch]

E [inch]

WPR [psi]

WPR [psi]

WPR [psi]

WPR [psi]

4 14.7 22.5 4.0 335 200 130

6 16.0 26.2 6.0 335 250 200 1308 17.0 27.7 6.5 335 250 200 13010 19.1 31.1 6.5 335 250 200 13012 21.0 34.2 8.0 335 250 200 13014 24.0 36.8 8.0 335 250 200 13016 27.0 39.4 8.0 335 250 200 13018 30.0 42.0 8.0 335 250 200 13020 33.0 44.6 8.0 335 250 200 13022 36.0 47.2 8.0 335 250 200 130

24 48.0 59.0 8.0 335 250 200 13026 49.0 62.0 10.0 250 200 13028 52.0 64.6 10.0 250 200 13030 54.0 66.4 10.0 250 200 13036 57.0 69.4 10.0 250 200 130



Size[inch] Part No.

R [inch]

X [inch]

E [inch]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

4 6.8 6.9 6.0 220 3.5 160 3

6 10.0 7.4 6.0 220 8 160 78 10.7 8.3 6.5 220 19 160 1510 13.5 8.7 6.5 220 31 160 2612 16.0 10.6 8.0 220 52 160 4214 14.5 10.9 8.0 220 66 160 5316 16.8 11.3 8.0 220 86 160 7018 18.4 11.7 8.0 220 114 160 9320 20.4 12.1 8.0 220 148 160 11922 22.4 12.6 8.0 220 178 160 14424 24.5 13.0 8.0 220 221 160 18026 26.5 15.4 10.0 160 24728 28.5 15.8 10.0 160 29730 30.5 16.2 10.032 38.0 16.6 10.0

34 41.0 17.0 10.036 43.0 17.5 10.042 50.0 24.7 16.048 58.0 25.9 16.054 64.0 27.2 16.0

Size [inch]


Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

4 130 2.5 85 2.56 130 6 85 68 130 13 85 910 130 21 85 1512 130 35 85 2414 130 44 85 3016 130 58 85 3918 130 79 85 5320 130 99 85 6722 130 121 85 8224 130 151 85 10126 130 208 85 14128 130 249 85 16530 130 286 85 19332 130 331 85 224

34 130 383 85 25736 130 441 85 29642 85 432 65 35248 65 478 50 38954 50 538 45 432



Size[inch] Part No.

R [inch]

X [inch]

E [inch]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

2 12.7 6.6 4.0 250 1.5 200 1

3 13.2 6.8 4.0 250 3 200 24 13.7 7.0 4.0 250 6 200 56 14.7 9.4 6.0 250 11 200 118 16.0 10.3 6.5 250 24 200 1910 17.0 10.7 6.5 250 39 200 3212 19.1 12.8 8.0 250 62 200 5114 21.0 13.2 8.0 250 79 200 6416 24.0 14.0 8.0 250 112 200 9118 27.0 14.7 8.0 250 146 200 11920 30.0 15.5 8.0 250 187 200 15122 33.0 16.3 8.0 250 243 200 19724 36.0 17.0 8.0 250 298 200 24426 48.0 21.4 10.0 200 33028 49.0 21.8 10.0 200 39330 52.0 22.5 10.032 54.0 23.1 10.034 55.0 23.5 10.036 58.0 24.2 10.042 63.0 31.7 16.048 72.0 34.0 16.054 81.0 36.2 16.0

SDR 11 SDR 17 SDR 21 SDR 26 SDR 32.5Size[inch]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

2 160 1 105 1

3 160 2 105 24 160 4 105 46 160 9 105 98 160 16 105 1210 160 26 105 1812 160 43 105 2914 160 53 105 3616 160 76 105 5118 160 101 105 6820 160 126 105 8622 160 165 105 11124 160 202 105 13726 160 277 105 18728 160 329 105 21830 160 388 105 26232 160 464 105 31234 160 537 105 36136 160 618 105 41642 105 621 80 50648 80 700 65 57054 65 954 50 766





Size[inch] Part No.

R [inch]

X [inch]

E [inch]

WPR [psi]

WPR [psi]

WPR [psi]

WPR [psi]

WPR [psi]

4 10.0 13.4 6.0 335 250 200 130

6 10.7 14.3 6.0 335 250 200 1308 13.5 15.2 6.5 335 250 200 13010 16.0 17.1 6.5 335 250 200 13012 14.5 18.9 8.0 335 250 200 13014 16.8 19.3 8.0 335 250 200 13016 18.4 19.7 8.0 335 250 200 13018 20.4 20.1 8.0 335 250 200 13020 22.4 20.6 8.0 335 250 200 13022 24.5 21.0 8.0 335 250 200 13024 26.5 23.4 8.0 335 250 200 13030 38.4 26.6 10.0 250 200 130

36 45.6 27.9 10.0 200 130 100




Size[inch] Part No.

R [inch]

X [inch]

E [inch]

WPR [psi]

WPR [psi]

WPR [psi]

WPR [psi]

4 14.7 13.4 4.0 335 250 200 130

6 16.0 16.3 6.0 335 250 200 1308 17.0 17.2 6.5 335 250 200 13010 19.1 19.3 6.5 335 250 200 13012 21.0 21.2 8.0 335 250 200 13014 24.0 22.0 8.0 335 250 200 13016 27.0 22.7 8.0 335 250 200 13018 30.0 23.5 8.0 335 250 200 13020 33.0 24.3 8.0 335 250 200 13022 36.0 25.0 8.0 335 250 200 13024 48.0 29.4 8.0 335 250 200 13026 49.0 31.8 10.0 250 200 130

28 52.0 32.5 10.0 250 200 130

30 54.0 33.1 10.0 250 200 130

36 57.0 34.2 10.0 250 200 130


IPS 2-Segment 22.5 Elbow (1/16 Bend)SDR 7 SDR 9

Size[inch] Part No.

R [inch]

X [inch]

E [inch]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

2 3.6 4.3 4.0 250 1 200 1

3 5.3 4.4 4.0 250 2 200 24 6.8 4.5 4.0 250 3.5 200 36 10.0 6.7 6.0 250 9 200 78 10.7 7.4 6.5 250 16 200 1310 13.5 7.6 6.5 250 26 200 2112 16.0 9.3 8.0 250 43 200 3514 14.5 9.4 8.0 250 53 200 4216 16.8 9.6 8.0 250 73 200 6118 18.4 9.8 8.0 250 92 200 7520 20.4 10.0 8.0 250 114 200 9222 22.4 10.2 8.0 250 146 200 11824 24.5 10.4 8.0 250 173 200 14126 26.5 12.6 10.0 200 20128 28.5 12.8 10.0 200 23330 30.5 13.0 10.032 38.0 13.2 10.034 41.0 13.4 10.036 43.0 13.6 10.042 50.0 20.2 16.048 58.0 20.8 16.0

54 64.0 21.4 16.0

Size[inch]


Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

2 160 1 105 13 160 1.5 105 1.54 160 2.5 105 2.56 160 6 105 68 160 11 105 910 160 17 105 1212 160 31 105 2014 160 35 105 2416 160 49 105 3318 160 63 105 4320 160 77 105 5222 160 99 105 6724 160 117 105 7926 160 170 105 11628 160 196 105 13030 160 224 105 15232 160 267 105 17934 160 301 105 20336 160 338 105 22742 105 324 80 26448 80 350 65 28554 65 537 50 431


IPS 2-Segment 22.5 Elbow (1/16 Bend)



Size[inch] Part No.

R [inch]

X [inch]

E [inch]

WPR [psi]

WPR [psi]

WPR [psi]

WPR [psi]

WPR [psi]

4 10.0 10.7 6.0 335 250 200 130

6 10.7 13.4 6.0 335 250 200 1308 13.5 14.0 6.5 335 250 200 13010 16.0 15.8 6.5 335 250 200 13012 145.0 17.4 8.0 335 250 200 13014 16.8 17.6 8.0 335 250 200 13016 18.4 17.8 8.0 335 250 200 13018 20.4 18.0 8.0 335 250 200 13020 22.4 18.2 8.0 335 250 200 13022 24.5 18.4 8.0 335 250 200 13024 26.5 20.6 8.0 335 250 200 13030 38.4 23.2 10.0 250 200 13036 45.6 23.8 10.0 200 130 100

DIPS 3-Segment 90 Elbow (1/4 Bend)SDR 9 SDR 11

Size[inch] Part No.

R [inch]

X [inch]

E [inch]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

4 7.2 11.2 6.0 160 8 130 6

6 10.4 13.5 6.0 160 16 130 138 11.3 15.0 6.5 160 27 130 2410 13.9 16.9 6.5 160 44 130 3712 16.5 20.4 8.0 160 75 130 6214 16.1 20.6 8.0 160 103 130 8516 18.3 22.3 8.0 160 141 130 11918 19.9 23.7 8.0 160 187 130 15520 22.0 25.4 8.0 160 239 130 20624 26.3 28.8 8.0 160 378 130 321

30 38.0 38.9 10.0 130 731

Size[inch]

SDR 17WPR [psi]

Weight [lbs]

4 85 46 85 98 85 1710 85 2612 85 4414 85 5816 85 7818 85 10420 85 13724 85 21530 85 492



Size[inch] Part No.

R [inch]

X [inch]

E [inch]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

4 14.0 17.7 6.0 200 11 160 9

6 15.0 18.7 6.0 200 21 160 178 16.2 20.4 6.5 200 35 160 3210 17.2 21.4 6.5 200 56 160 4712 19.8 25.2 8.0 200 94 160 7814 23.0 28.0 8.0 200 134 160 11416 26.1 30.6 8.0 200 187 160 16118 29.3 33.4 8.0 200 256 160 21120 32.4 36.1 8.0 200 328 160 27624 38.7 41.6 8.0 200 531 160 44930 48.0 51.6 10.0 160 847

Size[inch]

SDR 17WPR [psi]

Weight [lbs]

4 105 56 105 128 105 2510 105 3312 105 5514 105 7616 105 10618 105 14220 105 18724 105 30130 105 570



Size[inch] Part No.

R [inch]

X [inch]

E [inch]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

4 7.2 7.0 6.0 160 5 130 4

6 10.4 7.4 6.0 160 10 130 88 11.3 8.4 6.5 160 17 130 1510 13.9 8.8 6.5 160 27 130 2512 16.5 10.7 8.0 160 46 130 3814 16.1 11.2 8.0 160 64 130 5316 18.3 11.6 8.0 160 86 130 7418 19.9 12.0 8.0 160 109 130 9020 22.0 12.5 8.0 160 139 130 11724 26.3 13.3 8.0 160 207 130 17530 38.0 16.6 10.0 130 336

Size[inch]

SDR 17WPR [psi]

Weight [lbs]

4 85 36 85 68 85 1110 85 1612 85 2714 85 3616 85 4818 85 6120 85 7924 85 11730 85 226



Size[inch] Part No.

R [inch]

X [inch]

E [inch]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

4 14.0 9.1 6.0 200 6 160 4.5

6 15.0 9.4 6.0 200 13 160 118 16.2 10.4 6.5 200 21 160 1910 17.2 10.8 6.5 200 34 160 2812 19.8 13.0 8.0 200 58 160 4814 23.0 13.8 8.0 200 80 160 6616 26.1 14.5 8.0 200 111 160 9518 29.3 15.3 8.0 200 146 160 12120 32.4 16.1 8.0 200 183 160 15424 38.7 17.7 8.0 200 288 160 24330 48.0 22.0 10.0 160 464

Size[inch]

SDR 17WPR [psi]

Weight [lbs]

4 105 36 105 78 105 1410 105 2012 105 3414 105 4516 105 6218 105 8120 105 10524 105 16330 105 312


DIPS 2-Segment 22.5 Elbow (1/16 Bend)SDR 9 SDR 11

Size[inch] Part No.

R [inch]

X [inch]

E [inch]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

4 7.2 6.5 6.0 200 4 160 3

6 10.4 6.7 6.0 200 9 160 78 11.3 7.4 6.5 200 14 160 1310 13.9 7.6 6.5 200 24 160 2012 16.5 9.3 8.0 200 39 160 3214 16.1 9.5 8.0 200 56 160 4516 18.3 9.7 8.0 200 69 160 6018 19.9 9.9 8.0 200 89 160 7320 22.0 10.1 8.0 200 114 160 9624 26.3 10.6 8.0 200 162 160 13730 38.0 13.2 10.0 160 267

Size[inch]

SDR 17WPR [psi]

Weight [lbs]

4 105 26 105 58 105 1010 105 1412 105 2314 105 3116 105 3918 105 5020 105 6524 105 9230 105 179


Fabricated TeesIPS Fabricated Line Tee

Size[inch] Part No.

SDR 7 SDR9A [inch]

B [inch]

C [inch]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

4 16.5 6.0 8.3 235 8 175 7

6 18.6 6.0 9.3 235 19 175 158 24.6 8.0 12.3 235 42 175 3410 26.8 8.0 13.4 235 70 175 5712 28.8 8.0 14.4 235 105 175 8514 32.0 9.0 16.0 235 140 175 11216 34.0 9.0 17.0 235 204 175 16618 38.0 10.0 19.0 235 283 175 23120 40.0 10.0 20.0 235 368 175 29722 46.0 12.0 23.0 235 506 175 40924 48.0 12.0 24.0 235 983 175 50726 54.0 14.0 27.0 175 68628 56.0 14.0 28.0 175 82130 58.0 14.0 29.032 60.0 14.0 30.034 74.0 20.0 50.036 76.0 20.0 51.042 82.0 20.0 54.048 88.0 20.0 57.054 94.0 20.0 60.0

Size[inch]


Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

4 140 66 14 138 140 28 90 3210 140 46 90 3212 140 72 90 4814 140 93 90 6316 140 137 90 9218 11 140 90 13120 140 247 90 16722 140 343 90 23124 140 422 90 28626 140 577 90 39028 140 689 90 45730 140 816 90 55232 140 957 90 64334 140 1454 90 97736 140 1676 90 112842 90 1633 70 133148 70 1736 55 141354 55 2026 45 1628


IPS Fabricated Line Tee



Size[inch] Part No.

A [inch]

B [inch]

C [inch]

WPR [psi]

WPR [psi]

WPR [psi]

WPR [psi]

4 30.6 10.0 15.3 335 250 200 130

6 36.6 14.0 18.3 335 250 200 1308 39.8 14.5 19.9 335 250 200 13010 41.8 14.5 20.9 335 250 200 13012 48.0 17.0 24.0 335 250 200 13014 50.0 17.0 25.0 335 250 200 13016 54.0 18.0 27.0 335 250 200 13018 56.0 18.0 28.0 335 250 200 13020 62.0 20.0 31.0 335 250 200 13022 64.0 20.0 32.0 335 250 200 13024 70.0 22.0 35.0 335 250 200 130

DIPS Fabricated Line Tee

Size[inch] Part No.

SDR 9 SDR11A [inch]

B [inch]

C [inch]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

4 16.8 6.0 8.4 175 9 140 7

6 18.9 6.0 9.5 175 18 140 158 25.0 8.0 12.5 175 37 140 3410 27.1 8.0 13.6 175 62 140 5112 29.2 8.0 14.6 175 93 140 7814 33.3 9.0 16.7 175 50 140 12416 35.4 9.0 17.7 175 205 140 17518 39.5 10.0 19.8 175 286 140 23620 41.6 10.0 20.8 175 359 140 30224 49.8 12.0 24.9 175 612 140 51630 60.0 14.0 30.0 140 963

Size[inch]

SDR 17WPR [psi]

Weight [lbs]

4 90 56 90 108 90 2310 90 3712 90 5414 90 8416 90 11518 90 15920 90 20624 90 34830 90 647


IPS Branch Saddle Reducing Tee

• Fully Pressure Rated

SDR 7 SDR 9 SDR 11 SDR 17 SDR21

Size[inch] Part No.

A [inch]

B [inch]

C [inch]

WPR [psi]

WPR [psi]

WPR [psi]

WPR [psi]

WPR [psi]

4 x 2 18.0 7.2 11.3 335 250 200 1304 x 3 18.0 6.7 12.3 335 250 200 1306 x 2 18.0 7.2 13.3 335 250 200 1306 x 3 18.0 6.7 13.3 335 250 200 1306 x 4 19.0 6.7 13.3 335 250 200 1308 x 2 18.0 7.2 13.8 335 250 200 1308 x 3 18.0 6.7 14.6 335 250 200 1308 x 4 19.0 6.2 14.3 335 250 200 1308 x 6 21.0 6.2 14.3 335 250 200 13010 x 2 18.0 7.2 14.4 335 250 200 13010 x 3 18.0 6.7 15.9 335 250 200 13010 x 4 19.0 6.2 15.4 335 250 200 13010 x 6 21.0 6.2 15.4 335 250 200 13010 x 8 24.0 6.6 24.4 335 250 200 13012 x 2 20.0 8.2 15.4 335 250 200 13012 x 3 21.0 8.2 16.4 335 250 200 13012 x 4 23.0 8.2 16.4 335 250 200 13012 x 6 24.0 7.7 16.4 335 250 200 13012 x 8 28.0 8.6 25.4 335 250 200 13012 x 10 30.0 8.6 26.4 335 250 200 13014 x 2 20.0 8.2 16.7 335 250 200 13014 x 3 21.0 8.2 17.5 335 250 200 13014 x 4 23.0 8.2 17.2 335 250 200 13014 x 6 24.0 7.7 17.0 335 250 200 13014 x 8 28.0 8.6 26.8 335 250 200 13014 x 10 30.0 8.6 27.0 335 250 200 13014 x 12 32.0 8.5 29.0 335 250 200 13016 x 2 24.0 10.2 17.7 335 250 200 13016 x 3 24.0 9.7 18.5 335 250 200 13016 x 4 27.0 10.2 18.2 335 250 200 130 8016 x 6 29.0 10.2 18.0 335 250 200 130 8016 x 8 32.0 10.6 27.8 335 250 200 130 8016 x 10 34.0 10.6 28.0 335 250 200 130 8016 x 12 36.0 10.5 30.0 335 250 200 130 8018 x 2 24.0 10.2 18.5 335 250 200 130 8018 x 3 24.0 9.7 19.3 335 250 200 130 8018 x 4 27.0 10.2 19.0 335 250 200 130 8018 x 6 29.0 10.2 18.6 335 250 200 130 8018 x 8 32.0 10.6 28.6 335 250 200 130 8018 x 10 34.0 10.6 29.0 335 250 200 130 8018 x 12 36.0 10.5 31.0 335 250 200 130 80


IPS Branch Saddle Reducing Tee (continued)


SDR 7 SDR 9 SDR 11 SDR 17 SDR21

Size[inch] Part No.

A [inch]

B [inch]

C [inch]

WPR [psi]

WPR [psi]

WPR [psi]

WPR [psi]

WPR [psi]

20 x 2 28.0 12.2 19.5 335 250 200 130 8020 x 3 29.0 12.2 20.3 335 250 200 130 8020 x 4 31.0 7.2 20.0 335 250 200 130 8020 x 6 33.0 12.2 19.6 335 250 200 130 8020 x 8 36.0 12.6 29.6 335 250 200 130 8020 x 10 38.0 12.6 30.0 335 250 200 130 8020 x 12 40.0 12.5 32.0 335 250 200 130 8022 x 2 28.0 12.2 20.5 335 250 200 130 8022 x 3 29.0 12.2 21.3 335 250 200 130 8022 x 4 31.0 7.2 21.0 335 250 200 130 8022 x 6 33.0 12.2 20.6 335 250 200 130 8022 x 8 36.0 12.6 30.6 335 250 200 130 8022 x 10 38.0 12.6 31.2 335 250 200 130 8022 x 12 40.0 12.5 33.0 335 250 200 130 8024 x 2 28.0 12.2 21.5 335 250 200 130 8024 x 3 29.0 12.2 22.3 335 250 200 130 8024 x 4 31.0 7.2 22.0 335 250 200 130 8024 x 6 33.0 12.2 21.6 335 250 200 130 8024 x 8 36.0 12.6 31.6 335 250 200 130 8024 x 10 38.0 12.6 32.2 335 250 200 130 8024 x 12 40.0 12.5 34.0 335 250 200 130 80


DIPS Branch Saddle Reducing Tee


SDR 9 SDR 11 SDR 17 SDR21

Size[inch] Part No.

A [inch]

B [inch]

C [inch]

WPR [psi]

WPR [psi]

WPR [psi]

WPR [psi]

6 x 4 19.0 6.2 13.3 250 200 1308 x 4 19.0 6.2 14.3 250 200 1308 x 6 21.0 6.2 14.3 250 200 13010 x 4 19.0 6.2 15.4 250 200 13010 x 6 21.0 6.2 15.4 250 200 13010 x 8 24.0 6.2 24.4 250 200 13012 x 4 23.0 8.2 16.6 250 200 13012 x 6 24.0 7.7 16.4 250 200 13012 x 8 28.0 8.2 25.4 250 200 13012 x 10 30.0 8.6 26.4 250 200 13014 x 4 23.0 8.2 17.6 250 200 13014 x 6 24.0 7.7 17.0 250 200 13014 x 8 28.0 8.2 27.1 250 200 13014 x 10 30.0 8.1 27.0 250 200 13014 x 12 32.0 8.4 29.0 250 200 13016 x 4 28.0 10.2 18.7 250 200 130 8016 x 6 29.0 10.2 18.0 250 200 130 8016 x 8 32.0 10.2 28.2 250 200 130 8016 x 10 34.0 10.1 28.0 250 200 130 8016 x 12 36.0 10.4 30.0 250 200 130 8018 x 4 27.0 10.2 19.7 250 200 130 8018 x 6 29.0 10.2 20.2 250 200 130 8018 x 8 32.0 10.2 29.2 250 200 130 8018 x 10 34.0 10.1 29.7 250 200 130 80

18 x 12 36.0 10.4 31.7 250 200 130 8020 x 4 31.0 12.2 21.3 250 200 130 8020 x 6 33.0 12.2 21.3 250 200 130 8020 x 8 36.0 12.2 30.3 250 200 130 8020 x 10 38.0 12.1 30.8 250 200 130 8020 x 12 40.0 12.4 32.8 250 200 130 8024 x 4 31.0 12.2 22.9 250 200 130 8024 x 6 33.0 12.2 23.4 250 200 130 8024 x 8 36.0 12.2 32.4 250 200 130 8024 x 10 38.0 12.1 32.9 250 200 130 8024 x 12 40.0 12.4 34.9 250 200 130 80


Tapped Tees IPS & DIPS Main Size

SDR 11 SDR17Size[inch] Part No.

L [inch]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

4 12.0 200 56 12.0 200 118 12.0 200 1510 15.0 200 2212 15.0 200 2914 18.0 200 4416 20.0 200 6318 24.0 200 9120 24.0 200 11124 24.0 200 15728 IPS Only 30.0 200 22730 30.0 200 29436 IPS Only 36.0 130 302


Fabricated Wyes

IPS 45 Lateral Wye

Size[inch] Part No.

SDR 7 SDR9A [inch]

B [inch]

C [inch]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

2 18.0 6.0 14.0 130 3 100 2

3 18.0 7.0 14.0 130 7 100 6

4 22.0 7.0 22.0 130 16 100 14

6 28.0 7.0 28.0 130 42 100 338 30.0 8.0 30.0 130 74 100 5910 31.0 8.0 31.0 130 119 100 9812 33.0 11.0 33.0 130 181 100 14814 42.0 11.0 42.0 130 271 100 21716 44.0 13.0 44.0 130 383 100 31118 57.0 14.0 57.0 130 605 100 49320 65.0 14.0 65.0 130 838 100 67522 67.0 14.0 67.0 130 1044 100 84524 69.0 15.0 69.0 130 1272 100 103326 70.0 17.0 70.0 100 127228 71.0 18.0 71.0 100 149530 90.0 18.0 90.032 91.0 19.0 91.034 93.0 20.0 93.036 95.0 20.0 95.042 109.0 25.0 109.048 113.0 26.0 113.054 118.0 29.0 118.0

Size[inch]


Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

2 80 23 80 54 80 126 80 308 80 5110 80 79 50 5512 80 124 50 8414 80 181 50 12316 80 258 50 17418 80 415 50 28020 80 563 50 38222 80 710 50 47724 80 861 50 58326 80 1071 50 72328 80 1256 50 83230 80 1759 50 119132 80 2030 50 136534 80 2344 50 157536 80 2683 50 180742 50 2835 40 231048 40 3045 30 247954 30 3412 25 2742


IPS 45 Lateral Wye

• Reinforced • Fully Pressure Rated With Full Flow ID

SDR 9 SDR 11 SDR 17

Size [inch] Part No.A [inch]

B [inch]

C [inch]

WPR [psi]

WPR [psi]

WPR [psi]

4 28.0 13.0 28.0 250 200 1306 30.0 14.0 30.0 250 200 1308 31.0 14.5 31.0 250 200 13010 33.0 17.5 33.0 250 200 13012 42.0 19.0 42.0 250 200 13014 44.0 21.0 44.0 250 200 13016 57.0 22.0 57.0 250 200 13018 65.0 22.0 65.0 250 200 13020 67.0 22.0 67.0 250 200 13022 69.0 23.0 69.0 250 200 13024 70.0 23.0 70.0 250 200 130

IPS True Equal Wye

Size[inch] Part No.

SDR 11A [inch]

WPR [psi]

Weight [lbs]

4 9.0 80 6

6 12.0 80 178 16.0 80 3610 20.0 80 6912 24.0 80 11514 28.0 80 16116 32.0 80 24618 36.0 80 34820 40.0 80 47522 44.0 80 63124 48.0 80 816

IPS True Equal Wye


SDR 9 SDR 11 SDR 17

Size[inch] Part No.

Feedstock OD [inch]

A [inch]

WPR [psi]

WPR [psi]

WPR [psi]

4 6.625 12.0 250 200 1306 8.625 16.0 250 200 1308 10.750 20.0 250 200 13010 12.750 24.0 250 200 13012 14.000 28.0 250 200 13014 16.000 32.0 250 200 13016 20.000 40.0 250 200 13018 22.000 44.0 250 200 13020 24.000 48.0 250 200 13022 26.000 48.0 200 13024 28.000 48.0 200 130


DIPS 45 Lateral Wye

Size[inch] Part No.

SDR 9 SDR11A [inch]

B [inch]

C [inch]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

4 22.0 7.0 22.0 100 16 80 11

6 28.0 7.0 28.0 100 35 80 298 30.0 8.0 30.0 100 60 80 5410 31.0 8.0 31.0 100 97 80 7812 33.0 11.0 33.0 100 155 80 12414 42.0 11.0 42.0 100 241 80 20316 44.0 13.0 44.0 100 334 80 28618 57.0 14.0 57.0 100 542 80 44220 65.0 14.0 65.0 100 747 80 60924 69.0 15.0 69.0 100 1096 80 92630 91.0 19.0 91.0 80 1840

Size[inch]

SDR 17WPR [psi]

Weight [lbs]

4 50 76 50 178 50 3810 50 5612 50 8714 50 13516 50 19118 50 30620 50 41424 50 62230 50 1238

IPS 45 Lateral Reducing Wye

• Full Pressure Rated

Size[inch] Part No.

SDR 11A [inch]

B [inch]

WPR [psi]

Weight [lbs]

8 x 4 38.0 30.0 200 37

10 x 4 39.0 31.0 200 5112 x 4 44.0 33.0 200 8710 x 6 39.0 31.0 200 7212 x 6 44.0 33.0 200 9614 x 6 53.0 42.0 200 12912 x 8 44.0 33.0 200 10914 x 8 53.0 42.0 200 143


Fabricated Crosses

IPS Line Cross

Size[inch] Part No.

SDR 7 SDR9A [inch]

B [inch]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

2 9.0 3.3

3 10.3 3.4

4 16.5 6.0 130 10 100 8

6 18.6 6.0 130 22 100 188 24.6 8.0 130 50 100 4110 26.8 8.0 130 83 100 6712 28.8 8.0 130 123 100 9914 32.0 9.0 130 165 100 13216 34.0 9.0 130 236 100 119218 38.0 10.0 130 328 100 26720 40.0 10.0 130 423 100 34222 46.0 12.0 130 586 100 47424 48.0 12.0 130 1079 100 58426 54.0 14.0 100 79228 56.0 14.0 100 94430 58.0 14.032 60.0 14.034 74.0 20.036 76.0 20.042 82.0 20.048 88.0 20.054 94.0 20.0

Size[inch]


Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

2 80 23 80 34 80 76 80 168 80 3410 80 55 50 3812 80 84 50 5614 80 109 50 7416 80 159 50 10718 80 224 50 15220 80 284 50 19222 80 397 50 26724 80 487 50 32926 80 663 50 44928 80 791 50 52530 80 934 50 63132 80 1092 50 73334 80 1670 50 112336 80 1920 50 129242 50 1856 40 151448 40 1967 30 160254 30 2273 25 1827


IPS Line Cross


SDR 9 SDR 11 SDR 17

Size[inch] Part No.

Feedstock OD[inch]

A[inch]

B[inch]

WPR [psi]

WPR [psi]

WPR [psi]

4 6.625 15.3 12.0 200 160 1006 8.625 18.3 14.0 200 160 1008 10.750 19.9 14.5 200 160 10010 12.750 20.9 14.5 200 160 10012 14.000 24.0 17.0 200 160 10014 16.000 25.0 17.0 200 160 10016 18.000 27.0 18.0 200 160 10018 20.000 28.0 18.0 200 160 10020 22.000 31.0 20.0 200 160 10022 24.000 32.0 20.0 200 160 10024 26.000 35.0 20.0 200 160 100

DIPS Fabricated Line Cross

Size[inch] Part No.

SDR 7 SDR9A[inch]

B[inch]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

4 16.8 6.0 160 11 128 8

6 18.9 6.0 160 20 128 178 25.0 8.0 160 44 128 4010 27.1 8.0 160 73 128 6012 29.2 8.0 160 108 128 9114 33.3 9.0 160 173 128 14316 35.4 9.0 160 235 128 20018 39.5 10.0 160 328 128 27120 41.6 10.0 160 411 128 34624 49.8 12.0 160 701 128 59130 60.0 14.0 128 1098

Size[inch]

SDR 11WPR [psi]

Weight [lbs]

46810 80 4312 80 6214 80 9716 80 13218 80 18320 80 23424 80 39830 80 737


Fabricated Reducer Bushings

IPS Reducers Bushings

• Pressure Rated for SDR Ordered

Size[inch] Part No.

SDR 9 SDR11L1[inch]

L2[inch]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

1-1/2 x 1-1/4 2.00 2.00 250 1 200 1

6 x 4 4.00 4.00 250 3 200 3*8 x 4 8.00 8.00 200 98 x 6 4.00 4.00 250 6 200 610 x 6 6.00 6.00 200 1210 x 8 6.00 6.00 250 13 200 1312 x 8 6.00 6.00 200 1912 x 10 6.00 6.00 250 20 200 2014 x 10 7.00 7.00 200 2614 x 12 7.00 7.00 250 28 200 2816 x 12 7.00 7.00 200 6416 x 14 7.00 7.00 250 36 200 3618 x 14 7.00 7.00 200 4518 x 16 7.00 7.00 250 47 200 4720 x 18 7.00 7.00 250 56 200 5622 x 20 7.00 7.00 250 69 200 6924 x 20 9.00 9.00 200 8224 x 22 9.00 9.00 250 84 200 84

* Manufactured as 2-step Reducer using 8 x 6 and 6 x 4

Size[inch]

SDR 13.5 SDR 17 SDR 21 SDR 26 SDR 32.5WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

1-1/2 x 1-1/46 x 4 160 3 130 3*8 x 4 160 9 130 98 x 6 160 6 130 610 x 6 160 12 130 1210 x 8 160 13 130 1312 x 8 160 19 130 1912 x 10 160 20 130 2014 x 10 160 26 130 2614 x 12 160 28 130 28 100 28 80 28 65 2816 x 12 160 64 130 64 100 64 80 64 65 6416 x 14 160 36 130 36 100 36 80 36 65 3618 x 14 160 45 130 45 100 45 80 45 65 4518 x 16 160 47 130 47 100 47 80 47 65 4720 x 18 160 56 130 56 100 56 80 56 65 5622 x 20 160 69 130 69 100 69 80 69 65 6924 x 20 160 82 130 82 100 82 80 82 65 8224 x 22 160 84 130 84 100 84 80 84 65 84

* Manufactured as 2-step Reducer using 8 x 6 and 6 x 4


DIPS Reducers Bushings

• Pressure Rated for SDR Ordered

Size[inch] Part No.

SDR 11 SDR13.5L1[inch]

L2[inch]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

4 x 3 3.00 3.00 200 2 160 2

6 x 4 3.00 3.00 200 3 160 38 x 6 5.00 5.00 200 8 160 810 x 8 6.00 6.00 200 15 160 1512 x 10 6.00 6.00 200 21 160 2114 x 12 7.00 7.00 200 33 160 3316 x 14 7.00 7.00 200 43 160 4318 x 16 7.00 7.00 200 52 160 5220 x 18 7.00 7.00 200 62 160 6224 x 20 14.00 11.00 200 129 160 129

Size[inch]

SDR 17 SDR 21 SDR 26 SDR 32.5WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

4 x 3 130 26 x 4 130 38 x 6 130 8 100 8 80 8 65 810 x 8 130 15 100 15 80 15 65 1512 x 10 130 21 100 21 80 21 65 2114 x 12 130 33 100 33 80 33 65 3316 x 14 130 43 100 43 80 43 65 4318 x 16 130 52 100 52 80 52 65 5220 x 18 130 62 100 62 80 62 65 6224 x 20 130 129 100 129 80 129 65 129


Fabricated Branch Saddles

IPS Branch Saddles

• Blank branch saddles stocked in SDR11. • Blanks machined per order to radius of main pipe OD; and re-bored to proper SDR. • Branch saddles can be machined to main sizes up to 63. • Purchaser must determine that concave/convex heater plate adapters

Outlet Size [inch]

Main Size Range [inch] Part No.

Base Diameter [inch]

SDR 11L1[inch]

L2[inch]

WPR [psi]

Weight [lbs]

2 3 - 54 3.2 0.2 2.6 200 1

3 4 - 54 3.2 0.5 3.9 200 14 6 - 54 3.2 0.5 4.8 200 26 8 - 54 3.2 0.7 7.3 200 48 10 - 54 6.0 0.7 9.4 200 910 12 - 54 6.0 1.0 11.5 200 1612 14 - 54 8.0 1.0 13.8 200 32

DIPS Branch Saddles

• Blank branch saddles stocked in SDR11. • Blanks machined per order to radius of main pipe OD; and re-bored to proper SDR. • Branch saddles can be machined to main sizes up to 63. • Purchaser must determine that concave/convex heater plate adapters

Outlet Size [inch]


Base Diameter [inch]

SDR 11L1[inch]

L2[inch]

WPR [psi]

Weight [lbs]

2 3 - 54 3.2 0.2 2.6 200 1

3 4 - 54 3.2 0.5 3.9 200 14 6 - 54 4.0 1.0 6.6 200 46 8 - 54 5.0 1.5 8.6 200 98 10 - 54 6.0 1.5 11.5 200 1710 12 - 54 8.0 2.0 13.8 200 3112 14 - 54 10.0 2.0 15.3 200 47


IPS Rectangular Base Service Saddle

Outlet Size [inch] Part No.

SDR 9L1[inch]

Rectangular Base Size

WPR [psi]

Weight [lbs]

1-1/4 x 3/4 2.83 2.44 x 2.00 250 0.2

1-1/4 x 1 2.83 2.44 x 2.00 250 0.21-1/2 x 3/4 2.83 2.44 x 2.00 250 0.21-1/2 x 1 2.83 2.44 x 2.00 250 0.22 x 3/4 2.83 2.44 x 2.00 250 0.22 x 1 2.83 2.44 x 2.00 250 0.22 x 1-1/4 2.06 2.44 x 2.00 250 0.23 x 3/4 2.83 2.44 x 2.00 250 0.23 x 1 2.83 2.44 x 2.00 250 0.23 x 1-1/4 2.06 2.44 x 2.00 250 0.24 x 3/4 2.83 2.44 x 2.00 250 0.24 x 1 2.83 2.44 x 2.00 250 0.24 x 1-1/4 2.06 2.44 x 2.00 250 0.26 x 3/4 2.83 2.44 x 2.00 250 0.26 x 1 2.83 2.44 x 2.00 250 0.26 x 1-1/4 2.06 2.44 x 2.00 250 0.28 x 1 2.83 2.44 x 2.00 250 0.1

IPS Rectangular Base Self-Tapping Tees

Outlet Size [inch] Part No.

SDR 9

L1Rectangular Base Size

WPR [psi]

Weight [lbs]

1-1/4 x 1 3.05 1.91 x 2.50 250 11-1/2 x 1 3.05 1.91 x 2.50 250 12 x 1 3.05 1.91 x 2.50 250 12 x 1-1/4 3.05 1.91 x 2.50 250 13 x 1 3.05 1.91 x 2.50 250 13 x 1-1/4 3.05 1.91 x 2.50 250 14 x 1 3.05 1.91 x 2.50 250 14 x 1-1/4 3.05 1.91 x 2.50 250 16 x 1 3.05 1.91 x 2.50 250 16 x 1-1/4 3.05 1.91 x 2.50 250 18 x 1 3.05 1.91 x 2.50 250 18 x 1-1/4 3.05 1.91 x 2.50 250 1


IPS & DIPS Tapping Sleeve / Saddle Assembly

• Full Pressure Rated - MSS SP-60 & AWWA C906 Compliant

Outlet Size [inch]


SDR 11G (Ring)[inch]

F (Flg. Face)[inch]

H (Height)[inch]

WPR [psi]

4 6 - 54 0.94 1.00 8.50 160

6 8 - 54 1.00 1.25 8.50 1608 10 - 54 1.12 1.50 9.00 16010 12 - 54 1.19 2.00 10.50 16012 14 - 54 1.50 2.25 10.50 160


Machined End Caps

IPS Machined End Caps

• Pressure Rated for SDR Listed

Size[inch] Part No.

SDR11 SDR13.5T (min)[inch]

OAL[inch]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

10 2.62 4.00 200 15 160 15

12 3.00 4.00 200 17 160 1714 3.00 4.00 200 19 160 1916 - (SDR11) 3.38 5.00 200 3216 2.87 4.00 160 2418 - (SDR11) 3.80 5.00 200 4118 3.22 4.00 160 3020 - (SDR11/17) 4.20 5.00 200 5020 3.00 4.00 160 5022 - (SDR11) 4.65 6.00 200 7522 3.70 5.00 160 4524 - (SDR11) 5.06 6.00 200 8924 4.00 5.00 160 68

Size[inch]


Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

10 130 15 110 15 100 15 80 15 65 1512 130 17 110 17 100 17 80 17 65 1714 130 19 110 19 100 19 80 19 65 19

16 130 24 110 24 100 24 80 24 65 2418 130 30 110 30 100 30 80 30 65 3020 - (SDR11/17) 130 5020 110 37 100 37 80 37 65 3722 130 45 110 45 100 45 80 45 65 4524 130 68 110 68 100 68 80 68 65 68

IPS Machined End Caps (10psi max.)

Size[inch] Part No.

Low PressureT (min)[inch]

OAL[inch]

WPR [psi]

Weight [lbs]

26 3.00 4.00 10 max. 62

28 3.00 4.00 10 max. 7230 3.00 4.00 10 max. 83

32 3.00 4.00 10 max. 9434 3.00 4.00 10 max. 10636 3.00 4.00 10 max. 11540 3.00 4.00 10 max. 14242 3.00 4.00 10 max. 15748 3.00 4.00 10 max. 20554 3.00 4.00 10 max. 253


DIPS Machined End Caps


Size[inch] Part No.

SDR11 SDR13.5T (min)[inch]

OAL[inch]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

4 1.00 3.00 200 2 160 2

6 1.50 3.00 200 4 160 48 2.00 3.00 200 6 160 610 2.40 4.00 200 12 160 1212 2.80 4.00 200 18 160 1814 3.30 5.00 200 30 160 3016 3.68 5.00 200 38 160 3818 4.12 5.00 200 48 160 4820 - (SDR11-13.5) 4.60 6.00 200 98 160 9820 3.70 5.0024 - (SDR11-13.5) 5.07 6.00 200 114 160 11424 4.38 5.00

Size[inch]


Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

4 130 2 110 2 100 2 80 2 65 26 130 4 110 4 100 4 80 4 65 48 130 6 110 6 100 6 80 6 65 610 130 12 110 12 100 12 80 12 65 1212 130 18 110 18 100 18 80 18 65 1814 130 30 110 30 100 30 80 30 65 3016 130 38 110 38 100 38 80 38 65 3818 130 48 110 48 100 48 80 48 65 4820 130 70 110 70 100 70 80 70 65 7024 130 94 110 94 100 94 80 94 65 94


Fabricated Water-StopsIPS Water-Stops (Thrust-Isolator / Wall-Pipe / Anchor Ring)


SDR 7 SDR 9

Size[inch] Part No.

L[inch]

OD[inch]

T[inch]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

2 12.0 3.50 2.00 335 2 250 2

3 12.0 5.00 2.00 335 3 250 34 12.0 6.60 2.00 335 4 250 46 12.0 8.50 2.00 335 7 250 78 16.0 10.63 2.00 335 15 250 1510 18.0 12.75 2.00 335 24 250 2412 22.0 15.00 2.00 335 39 250 3914 22.0 17.50 2.00 335 59 250 5916 24.0 20.00 2.00 335 88 250 8818 24.0 21.12 2.00 335 106 250 10620 24.0 23.50 2.00 335 131 250 13122 24.0 25.60 2.00 250 16324 28.0 28.00 2.00 250 18726 28.0 30.00 2.00 250 14128 28.0 32.00 2.00 250 16230 28.0 34.30 2.00 250 19132 30.0 36.50 2.0034 30.0 40.80 2.0036 30.0 40.80 2.2542 35.0 48.00 2.2548 35.0 54.00 2.25

54 35.0 60.00 2.25

Size[inch]


Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

2 200 2 130 2 100 2 80 2 65 23 200 3 130 3 100 3 80 3 65 34 200 4 130 4 100 4 80 4 65 46 200 7 130 7 100 7 80 7 65 78 200 15 130 15 100 15 80 15 65 15

10 200 24 130 24 100 24 80 24 65 2412 200 39 130 39 100 39 80 39 65 3914 200 59 130 59 100 59 80 59 65 5916 200 88 130 88 100 88 80 88 65 8818 200 106 130 106 100 106 80 106 65 10620 200 131 130 131 100 131 80 131 65 13122 200 163 130 163 100 163 80 163 65 16324 200 187 130 187 100 187 80 187 65 18726 200 141 130 141 100 141 80 141 65 14128 200 162 130 162 100 162 80 162 65 16230 200 191 130 191 100 191 80 191 65 19132 200 233 130 233 100 233 80 233 65 23334 200 264 130 264 100 264 80 264 65 26436 200 298 130 298 100 298 80 298 65 29842 130 336 100 336 80 336 65 33648 130 412 100 412 80 412 65 41254 100 574 80 574 65 574


DIPS Water-Stops (Thrust-Isolator / Wall-Pipe / Anchor Ring)


SDR 7 SDR 9

Size[inch] Part No.

L[inch]

OD[inch]

T[inch]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

3 12.0 5.00 2.00 335 3 250 34 12.0 6.60 2.00 335 4 250 46 12.0 8.50 2.00 335 7 250 78 16.0 10.63 2.00 335 15 250 1510 18.0 12.75 2.00 335 24 250 2412 22.0 15.00 2.00 335 39 250 3914 22.0 17.50 2.00 335 59 250 5916 24.0 20.00 2.00 335 88 250 8818 24.0 21.12 2.00 335 106 250 10620 24.0 23.50 2.00 335 131 250 13122 24.0 25.60 2.00 250 16324 28.0 28.00 2.00 250 187

Size[inch]


Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

WPR [psi]

Weight [lbs]

3 200 3 130 3 100 3 80 3 65 34 200 4 130 4 100 4 80 4 65 46 200 7 130 7 100 7 80 7 65 78 200 15 130 15 100 15 80 15 65 15

10 200 24 130 24 100 24 80 24 65 2412 200 39 130 39 100 39 80 39 65 3914 200 59 130 59 100 59 80 59 65 5916 200 88 130 88 100 88 80 88 65 8818 200 106 130 106 100 106 80 106 65 10620 200 131 130 131 100 131 80 131 65 13122 200 163 130 163 100 163 80 163 65 16324 200 187 130 187 100 187 80 187 65 187


Flange AdaptersIPS Flange Adapters (SDR 7 - 335 psi)

Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

3/4 4.0 0.20 2.00 1/4 0.11 4.0 0.21 2.37 1/4 0.11-1/4 4.0 0.25 2.75 1/4 0.21-1/2 4.0 0.30 3.12 1/4 0.22 6.0 0.39 3.94 1/4 13 6.0 0.63 5.00 1/4 24 6.0 0.54 6.00 3/8 35 6.0 0.99 7.50 3/8 56 8.0 0.78 8.50 3/8 78 11.0 1.00 10.63 3/8 1010 11.0 1.93 12.75 3/8 2012 11.0 2.28 15.00 3/8 2614 11.0 2.50 17.50 1/2 5116 12.0 2.86 20.00 1/2 7618 12.7 3.21 21.12 1/2 8020 12.8 3.57 23.50 1/2 94

IPS Flange Adapters (SDR 9 - 250 psi)

Size[inch] Part No.

H[inch]

T[inch]

Face Dia.

R (Radius)

Weight [lbs]

3/4 4.0 0.20 2.00 1/4 0.11 4.0 0.21 2.37 1/4 0.11-1/4 4.0 0.25 2.75 1/4 0.21-1/2 4.0 0.30 3.12 1/4 0.22 6.0 0.39 3.94 1/4 13 6.0 0.63 5.00 1/4 24 6.0 0.54 6.00 3/8 35 6.0 0.99 7.50 3/8 56 8.0 0.78 8.50 3/8 78 11.0 1.00 10.63 3/8 1010 11.0 1.49 12.75 3/8 19

12 11.0 1.77 15.00 3/8 2514 11.0 1.94 17.50 1/2 4916 12.0 2.22 20.00 1/2 7418 12.0 2.50 21.12 1/2 7920 12.0 2.78 23.50 1/2 8122 12.0 3.06 25.60 1/2 8324 14.0 3.33 28.00 1/2 9726 15.0 3.61 30.00 1/2 14328 15.7 3.89 32.30 1/2 15830 15.8 4.17 34.30 1/2 16432 15.8 4.44 36.50 1/2 186



Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

3/4 4.0 0.20 2.00 1/4 0.11 4.0 0.21 2.37 1/4 0.11-1/4 4.0 0.25 2.75 1/4 0.21-1/2 4.0 0.30 3.12 1/4 0.22 6.0 0.39 3.94 1/4 13 6.0 0.63 5.00 1/4 24 6.0 0.54 6.00 3/8 35 6.0 0.99 7.50 3/8 56 8.0 0.78 8.50 3/8 78 11.0 1.00 10.63 3/8 1010 11.0 1.22 12.75 3/8 1812 11.0 1.45 15.00 3/8 2414 11.0 1.60 17.50 1/2 4016 12.0 1.82 20.00 1/2 6018 12.0 2.05 21.12 1/2 6420 12.0 2.27 23.50 1/2 6622 12.0 2.50 25.60 1/2 6824 14.0 2.73 28.00 1/2 7926 15.0 2.96 30.00 1/2 11728 15.0 3.18 32.30 1/2 12930 15.0 3.41 34.30 1/2 13432 15.0 3.64 36.50 1/2 16334 15.9 4.72 38.50 1/2 20836 16.5 4.09 40.80 1/2 218

IPS Flange Adapters (SDR 13.5 - 160 psi)

Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

2 6.0 0.39 3.94 1/4 13 6.0 0.63 5.00 1/4 24 6.0 0.54 6.00 3/8 35 6.0 0.99 7.50 3/8 56 8.0 0.78 8.50 3/8 78 11.0 1.00 10.63 3/8 1010 11.0 1.22 12.75 3/8 1812 11.0 1.45 15.00 3/8 2414 11.0 1.60 17.50 1/2 4016 12.0 1.82 20.00 1/2 6018 12.0 2.05 21.12 1/2 6420 12.0 2.27 23.50 1/2 6622 12.0 2.50 25.60 1/2 6824 14.0 2.73 28.00 1/2 7926 15.0 2.96 30.00 1/2 11728 15.0 3.18 32.30 1/2 12930 15.0 3.41 34.30 1/2 13432 15.0 3.64 36.50 1/2 16334 15.9 4.72 38.50 1/2 20836 16.5 4.09 40.80 1/2 21842 22.4 3.89 47.50 1/2 167



Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

2 6.0 0.39 3.94 1/4 13 6.0 0.63 5.00 1/4 24 6.0 0.54 6.00 3/8 35 6.0 0.99 7.50 3/8 56 8.0 0.78 8.50 3/8 78 11.0 1.00 10.63 3/8 1010 11.0 1.22 12.75 3/8 1812 11.0 1.45 15.00 3/8 2414 11.0 1.60 17.50 1/2 4016 12.0 1.82 20.00 1/2 6018 12.0 2.05 21.12 1/2 6420 12.0 2.27 23.50 1/2 6622 14.0 2.50 25.60 1/2 6824 15.0 2.73 28.00 1/2 7926 15.0 2.96 30.00 1/2 11728 15.0 3.18 32.30 1/2 12930 15.0 3.41 34.30 1/2 13432 15.0 2.35 36.50 1/2 10634 15.0 3.86 38.50 1/2 13536 14.0 2.64 40.80 1/2 14142 21.0 3.09 47.50 1/2 18248 21.0 3.53 54.00 1/2 24454 22.4 4.00 60.00 1/2 304


Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

3 6.0 0.63 5.00 1/4 24 6.0 0.54 6.00 3/8 35 6.0 0.99 7.50 3/8 56 8.0 0.78 8.50 3/8 78 11.0 1.00 10.63 3/8 1010 11.0 1.22 12.75 3/8 1812 11.0 1.45 15.00 3/8 2414 11.0 1.60 17.50 1/2 4016 12.0 1.82 20.00 1/2 6018 12.0 2.05 21.12 1/2 6420 12.0 2.27 23.50 1/2 6622 14.0 2.50 25.60 1/2 6824 15.0 2.73 28.00 1/2 7926 15.0 2.96 30.00 1/2 11728 15.0 3.18 32.30 1/2 12930 15.0 3.41 34.30 1/2 13432 15.0 2.35 36.50 1/2 10634 15.0 3.86 38.50 1/2 13536 14.0 2.64 40.80 1/2 14142 21.0 3.09 47.50 1/2 18248 21.0 3.53 54.00 3/4 24454 21.6 4.00 60.00 3/4 304



Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

3 6.0 0.63 5.00 1/4 24 6.0 0.54 6.00 3/8 35 6.0 0.99 7.50 3/8 56 8.0 0.78 8.50 3/8 78 11.0 1.00 10.63 3/8 1010 11.0 1.22 12.75 3/8 1812 11.0 1.45 15.00 3/8 2414 11.0 1.60 17.50 1/2 4016 12.0 1.82 20.00 1/2 6018 12.0 2.05 21.12 1/2 6420 12.0 2.27 23.50 1/2 6622 14.0 2.50 25.60 1/2 6824 15.0 2.73 28.00 1/2 7926 15.0 2.96 30.00 1/2 11728 15.0 3.18 32.30 1/2 12930 15.0 3.41 34.30 1/2 13432 15.0 2.35 36.50 1/2 10634 15.0 3.86 38.50 1/2 13536 14.0 2.64 40.80 1/2 14142 21.0 2.50 47.50 1/2 15248 21.0 2.86 54.00 3/4 20454 21.6 3.21 60.00 3/4 264


Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

3 6.0 0.63 5.00 1/4 24 6.0 0.54 6.00 3/8 35 6.0 0.99 7.50 3/8 56 8.0 0.78 8.50 3/8 78 11.0 1.00 10.63 3/8 1010 11.0 1.22 12.75 3/8 1812 11.0 1.45 15.00 3/8 2414 11.0 1.60 17.50 1/2 4016 12.0 1.82 20.00 1/2 6018 12.0 2.05 21.12 1/2 6420 12.0 2.27 23.50 1/2 6622 14.0 2.50 25.60 1/2 6824 15.0 2.73 28.00 1/2 7926 15.0 2.96 30.00 1/2 11728 15.0 3.18 32.30 1/2 12930 15.0 3.41 34.30 1/2 13432 15.0 2.35 36.50 1/2 10634 15.0 3.86 38.50 1/2 13536 14.0 2.64 40.80 1/2 14142 21.0 2.50 47.50 1/2 15248 21.0 2.31 54.00 3/4 17054 21.0 2.60 60.00 3/4 230


IPS Flange Adapters (SDR 32.5 - 65 psi)

Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

3 6.0 0.63 5.00 1/4 24 6.0 0.54 6.00 3/8 35 6.0 0.99 7.50 3/8 56 8.0 0.78 8.50 3/8 78 11.0 1.00 10.63 3/8 1010 11.0 1.22 12.75 3/8 1812 11.0 1.45 15.00 3/8 2414 11.0 1.60 17.50 1/2 4016 12.0 1.82 20.00 1/2 6018 12.0 2.05 21.12 1/2 6420 12.0 2.27 23.50 1/2 6622 14.0 2.50 25.60 1/2 6824 15.0 2.73 28.00 1/2 7926 15.0 2.96 30.00 1/2 11728 15.0 3.18 32.30 1/2 12930 15.0 3.41 34.30 1/2 13432 15.0 2.35 36.50 1/2 10634 15.0 3.86 38.50 1/2 13536 14.0 2.64 40.80 1/2 14142 21.0 2.50 47.50 1/2 15248 21.0 2.31 54.00 3/4 17054 21.0 2.60 60.00 3/4 230


DIPS Flange Adapters (SDR 9 - 250 psi)

Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

4 6.0 0.67 6.63 7/16 46 8.0 0.96 8.63 7/16 68 9.0 1.26 10.75 7/16 810 9.0 1.54 12.75 7/16 1312 11.0 1.83 15.00 7/16 2114 11.0 2.13 17.50 7/16 3516 12.0 2.42 20.00 7/16 4318 12.0 2.71 21.50 7/16 5420 12.0 3.00 23.60 7/16 6824 14.8 3.58 27.80 7/16 99


Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

3 6.0 0.45 5.00 7/16 24 6.0 0.55 6.00 7/16 36 8.0 0.78 8.50 7/16 48 9.0 1.03 10.63 7/16 610 9.0 1.26 12.75 7/16 1012 11.0 1.50 15.00 7/16 1714 11.0 1.74 17.50 7/16 2816 12.0 1.98 20.00 7/16 3518 12.0 2.22 21.12 7/16 4620 12.0 2.46 23.50 7/16 5524 14.0 2.93 28.00 7/16 8130 15.0 3.64 34.30 1/2 134


Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

3 6.0 0.45 5.00 7/16 24 6.0 0.55 6.00 7/16 38 9.0 1.03 10.63 7/16 610 9.0 1.26 12.75 7/16 1012 11.0 1.50 15.00 7/16 1714 11.0 1.74 17.50 7/16 2816 12.0 1.98 20.00 7/16 3518 12.0 2.22 21.12 7/16 4620 12.0 2.46 23.50 7/16 5524 13.0 1.90 28.00 7/16 7530 15.0 3.64 34.30 1/2 134



Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

3 6.0 0.45 5.00 7/16 24 6.0 0.55 6.00 7/16 38 9.0 1.03 10.63 7/16 610 9.0 1.26 12.75 7/16 1012 11.0 1.50 15.00 7/16 1714 11.0 1.74 17.50 7/16 2816 12.0 1.98 20.00 7/16 3518 12.0 2.22 21.12 7/16 4620 12.0 2.46 23.50 7/16 5524 14.0 2.93 28.00 7/16 8130 15.0 3.64 34.30 1/2 134


Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

3 6.0 0.45 5.00 7/16 24 6.0 0.55 6.00 7/16 38 9.0 1.03 10.63 7/16 610 9.0 1.26 12.75 7/16 1012 11.0 1.50 15.00 7/16 1714 11.0 1.74 17.50 7/16 2816 12.0 1.98 20.00 7/16 3518 12.0 2.22 21.12 7/16 4620 12.0 2.46 23.50 7/16 5524 14.0 2.93 28.00 7/16 8130 15.0 3.64 34.30 1/2 134

DIPS Flange Adapters (SDR 32.5 - 65 psi)

Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

3 6.0 0.45 5.00 7/16 24 6.0 0.55 6.00 7/16 38 9.0 1.03 10.63 7/16 610 9.0 1.26 12.75 7/16 1012 11.0 1.50 15.00 7/16 1714 11.0 1.74 17.50 7/16 2816 12.0 1.98 20.00 7/16 3518 12.0 2.22 21.12 7/16 4620 12.0 2.46 23.50 7/16 5524 14.0 2.93 28.00 7/16 8130 15.0 3.64 34.30 1/2 134


IPS Butterfly Valve Flange Adapters (SDR 11)

Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

4 6.50 1.25 6.63 3/8 56 8.50 1.50 8.63 3/8 68 9.50 1.75 10.75 3/8 810 9.50 2.00 12.75 3/8 1212 11.50 2.25 15.00 3/8 19


Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

4 6.50 1.25 6.63 3/8 56 8.50 1.50 8.63 3/8 68 9.50 1.75 10.75 3/8 810 9.50 2.00 12.75 3/8 1212 11.50 2.25 15.00 3/8 19


Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

4 6.50 1.25 6.63 3/8 56 8.50 1.50 8.63 3/8 68 9.50 1.75 10.75 3/8 810 9.50 2.00 12.75 3/8 1212 11.50 2.25 15.00 3/8 19


Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

4 6.50 1.25 6.63 3/8 56 8.50 1.50 8.63 3/8 68 9.50 1.75 10.75 3/8 810 9.50 2.00 12.75 3/8 1212 11.50 2.25 15.00 3/8 19

IPS Butterfly Valve Flange Adapters (SDR 32.5)

Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

4 6.50 1.25 6.63 3/8 56 8.50 1.50 8.63 3/8 68 9.50 1.75 10.75 3/8 810 9.50 2.00 12.75 3/8 1212 11.50 2.25 15.00 3/8 19


DIPS Butterfly Valve Flange Adapters (SDR 11)

Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

4 6.50 1.25 6.63 3/8 56 8.50 1.50 8.63 3/8 68 9.50 1.75 10.75 3/8 810 9.50 2.00 12.75 3/8 1212 11.50 2.25 15.00 3/8 19


Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

4 6.50 1.25 6.63 3/8 56 8.50 1.50 8.63 3/8 68 9.50 1.75 10.75 3/8 810 9.50 2.00 12.75 3/8 1212 11.50 2.25 15.00 3/8 19


Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

4 6.50 1.25 6.63 3/8 56 8.50 1.50 8.63 3/8 68 9.50 1.75 10.75 3/8 810 9.50 2.00 12.75 3/8 1212 11.50 2.25 15.00 3/8 19


Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

4 6.50 1.25 6.63 3/8 56 8.50 1.50 8.63 3/8 68 9.50 1.75 10.75 3/8 810 9.50 2.00 12.75 3/8 1212 11.50 2.25 15.00 3/8 19

DIPS Butterfly Valve Flange Adapters (SDR 32.5)

Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

4 6.50 1.25 6.63 3/8 56 8.50 1.50 8.63 3/8 68 9.50 1.75 10.75 3/8 810 9.50 2.00 12.75 3/8 1212 11.50 2.25 15.00 3/8 19


Stub Ends

IPS Stub Ends (SDR 7 - 335 psi)

Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

14 4.50 2.50 17.50 1/2 4516 5.00 1.94 20.00 1/2 6418 5.10 3.21 21.12 1/2 6820 5.30 3.57 23.50 1/2 77


Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

14 4.30 1.94 17.50 1/2 3816 4.50 2.22 20.00 1/2 5318 4.50 2.50 21.12 1/2 5720 4.50 2.78 23.50 1/2 6422 4.60 3.06 25.60 1/2 7524 4.60 3.33 28.00 1/2 8826 5.50 3.61 30.00 1/2 4428 5.80 3.89 32.30 1/2 5330 4.17 4.17 34.30 1/2 64


Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

14 4.00 1.60 17.50 1/2 3216 4.00 1.82 20.00 1/2 4418 4.00 2.05 21.12 1/2 4820 4.00 2.27 23.50 1/2 5322 4.00 2.50 25.60 1/2 6224 4.00 2.73 28.00 1/2 7426 4.00 2.96 30.00 1/2 3628 4.80 3.18 32.30 1/2 4430 5.00 3.41 34.30 1/2 5332 5.30 3.64 36.50 1/2 6134 4.90 4.72 38.50 1/2 7136 5.40 4.09 40.80 1/2 80


IPS Stub Ends (SDR 13.5 - 160 psi)

Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

14 4.00 1.60 17.50 1/2 3216 4.00 1.82 20.00 1/2 4418 4.00 2.05 21.12 1/2 4820 4.00 2.27 23.50 1/2 5322 4.00 2.50 25.60 1/2 6224 4.00 2.73 28.00 1/2 7426 4.00 2.96 30.00 1/2 3628 4.80 3.18 32.30 1/2 4430 5.00 3.41 34.30 1/2 5332 5.30 3.64 36.50 1/2 6134 4.90 4.72 38.50 1/2 7136 5.40 4.09 40.80 1/2 8042 5.30 3.89 47.50 1/2 98


Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

14 4.00 1.60 17.50 1/2 3216 4.00 1.82 20.00 1/2 4418 4.00 2.05 21.12 1/2 4820 4.00 2.27 23.50 1/2 5322 4.00 2.50 25.60 1/2 6224 4.00 2.73 28.00 1/2 7426 4.00 2.96 30.00 1/2 3628 4.80 3.18 32.30 1/2 4430 5.00 3.41 34.30 1/2 5332 5.30 2.35 36.50 1/2 5134 4.90 3.86 38.50 1/2 5936 5.40 2.64 40.80 1/2 6742 5.30 3.09 47.50 1/2 8248 5.70 3.53 54.00 3/4 12454 5.90 4.00 60.00 3/4 218



Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

14 4.00 1.60 17.50 1/2 3216 4.00 1.82 20.00 1/2 4418 4.00 2.05 21.12 1/2 4820 4.00 2.27 23.50 1/2 5322 4.00 2.50 25.60 1/2 6224 4.00 2.73 28.00 1/2 7426 4.00 2.96 30.00 1/2 3628 4.80 3.18 32.30 1/2 4430 5.00 3.41 34.30 1/2 5332 5.30 2.35 36.50 1/2 5134 4.90 3.86 38.50 1/2 59

36 5.40 2.64 40.80 1/2 6742 5.30 3.09 47.50 1/2 8248 5.70 3.53 54.00 3/4 12454 5.90 4.00 60.00 3/4 218


Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

14 4.00 1.60 17.50 1/2 3216 4.00 1.82 20.00 1/2 4418 4.00 2.05 21.12 1/2 4820 4.00 2.27 23.50 1/2 5322 4.00 2.50 25.60 1/2 6224 4.00 2.73 28.00 1/2 7426 4.00 2.96 30.00 1/2 3628 4.80 3.18 32.30 1/2 4430 5.00 3.41 34.30 1/2 5332 5.30 2.35 36.50 1/2 5134 4.90 3.86 38.50 1/2 59

36 5.40 2.64 40.80 1/2 6742 4.50 2.50 47.50 1/2 6648 5.00 2.86 54.00 3/4 10454 5.10 3.21 60.00 3/4 182



Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

14 4.00 1.60 17.50 1/2 3216 4.00 1.82 20.00 1/2 4418 4.00 2.05 21.12 1/2 4820 4.00 2.27 23.50 1/2 5322 4.00 2.50 25.60 1/2 6224 4.00 2.73 28.00 1/2 7426 4.00 2.96 30.00 1/2 3628 4.80 3.18 32.30 1/2 4430 5.00 3.41 34.30 1/2 5332 5.30 2.35 36.50 1/2 5134 4.90 3.86 38.50 1/2 5936 5.40 2.64 40.80 1/2 6742 4.50 2.50 47.50 1/2 6648 4.50 2.31 54.00 3/4 8754 4.50 2.60 60.00 3/4 152

IPS Stub Ends (SDR 32.5 - 65 psi)

Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

14 4.00 1.60 17.50 1/2 3216 4.00 1.82 20.00 1/2 4418 4.00 2.05 21.12 1/2 4820 4.00 2.27 23.50 1/2 5322 4.00 2.50 25.60 1/2 6224 4.00 2.73 28.00 1/2 7426 4.00 2.96 30.00 1/2 3628 4.80 3.18 32.30 1/2 4430 5.00 3.41 34.30 1/2 5332 5.30 2.35 36.50 1/2 5134 4.90 3.86 38.50 1/2 5936 5.40 2.64 40.80 1/2 6742 4.50 2.50 47.50 1/2 6648 4.50 2.31 54.00 3/4 8754 4.50 2.60 60.00 3/4 152

DIPS Stub Ends (SDR 9 - 250 psi)

Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

14 4.00 2.13 17.50 7/16 2216 4.00 2.42 20.00 7/16 2918 4.00 2.71 21.50 7/16 3220 4.00 3.00 23.60 7/16 2924 4.50 3.58 27.80 7/16 55



Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

14 4.00 1.74 17.50 7/16 1816 4.00 1.98 20.00 7/16 2418 4.00 2.22 21.12 7/16 2720 4.00 2.46 23.50 7/16 3324 4.00 2.93 28.00 7/16 4630 5.00 3.64 34.30 1/2 110

DIPS Stub Ends (SDR 13.5 - 160 psi)

Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

14 4.00 1.74 17.50 7/16 1816 4.00 1.98 20.00 7/16 2418 4.00 2.22 21.12 7/16 2720 4.00 2.46 23.50 7/16 3324 4.00 2.93 28.00 7/16 4630 5.00 3.64 34.30 1/2 110


Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

14 4.00 1.74 17.50 7/16 1816 4.00 1.98 20.00 7/16 2418 4.00 2.22 21.12 7/16 2720 4.00 2.46 23.50 7/16 3324 4.00 2.93 28.00 7/16 4630 5.00 3.64 34.30 1/2 110


Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

14 4.00 1.74 17.50 7/16 1816 4.00 1.98 20.00 7/16 2418 4.00 2.22 21.12 7/16 2720 4.00 2.46 23.50 7/16 3324 4.00 2.93 28.00 7/16 4630 5.00 3.64 34.30 1/2 110



Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

14 4.00 1.74 17.50 7/16 1816 4.00 1.98 20.00 7/16 2418 4.00 2.22 21.12 7/16 2720 4.00 2.46 23.50 7/16 3324 4.00 2.93 28.00 7/16 4630 5.00 3.64 34.30 1/2 110


Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

14 4.00 1.74 17.50 7/16 1816 4.00 1.98 20.00 7/16 2418 4.00 2.22 21.12 7/16 2720 4.00 2.46 23.50 7/16 3324 4.00 2.93 28.00 7/16 4630 5.00 3.64 34.30 1/2 110

DIPS Stub Ends (SDR 32.5 - 65 psi)

Size[inch] Part No.

H[inch]

T[inch]

Face Dia.[inch]

R (Radius)

Weight [lbs]

14 4.00 1.74 17.50 7/16 1816 4.00 1.98 20.00 7/16 2418 4.00 2.22 21.12 7/16 2720 4.00 2.46 23.50 7/16 3324 4.00 2.93 28.00 7/16 4630 5.00 3.64 34.30 1/2 110


Butterfly Valve SpacersIPS Butterfly Valve Spacers

• For Use with HDPE Flange Adapters • For Best Fit GF Flange Adapters are Recommended

Size[inch] Part No.

PE Flg. Face OD[inch]

Spacer OD [inch]

Spacer ID[inch]

Spacer Length[inch]

Weight [lbs]

2 3.90 4.00 2.12 1.00 13 5.00 5.25 3.25 1.00 14 6.60 6.75 4.25 1.50 16 8.50 8.63 6.25 2.00 28 10.63 10.88 8.25 2.00 210 12.75 13.25 10.25 2.00 312 15.00 16.00 12.25 2.00 414 17.50 17.63 13.37 2.00 516 20.00 20.13 15.25 2.20 718 21.12 21.50 17.25 2.50 920 23.50 23.88 19.00 3.00 2122 25.60 25.88 21.00 4.00 2624 28.00 28.13 23.00 4.00 31

*Spacers available above 24 upon request

DIPS Butterfly Valve Spacers

• For Use with HDPE Flange Adapters • For Best Fit GF Flange Adapters are Recommeded

Size[inch] Part No.

PE Flg. Face OD[inch]

Spacer OD [inch]

Spacer ID[inch]

Spacer Length[inch]

Weight [lbs]

2 3.90 4.00 2.12 1.00 13 5.00 5.25 3.25 1.00 14 6.60 6.75 4.25 1.50 16 8.50 8.63 6.25 2.00 28 10.63 10.88 8.25 2.00 210 12.75 13.25 10.25 2.00 312 15.00 16.00 12.25 2.00 414 17.50 17.63 13.37 2.00 516 20.00 20.13 15.25 2.20 718 21.12 21.50 17.25 2.50 920 23.50 23.88 19.00 3.00 2122 25.60 25.88 21.00 4.00 2624 28.00 28.13 23.00 4.00 31

*Spacers available above 24 upon request


Blind Flanges

IPS/DIPS HDPE Blind Flanges

• Commonly used for closure or night-capping of flanged pipes. • HDPE Blind flanges are not pressure rated • Metal backup ring required for sealing at moderate pressures

Size[inch] Part No.

OD [inch]

Bolt Circle[inch]

Hole Dia.[inch]

Holes(ea)

Weight - 1“ Thk (lbs)

Weight - 2“ Thk (lbs)

2 6.00 4.75 3/4 4 4.00 13 7.50 6.00 3/4 4 5.25 14 9.00 7.50 3/4 8 6.75 16 11.00 9.50 7/8 8 8.63 28 13.50 11.75 7/8 8 10.88 210 16.00 14.25 1 12 13.25 312 19.00 17.00 1 12 16.00 414 21.00 18.75 1-1/8 12 17.63 516 23.50 21.25 1-1/8 16 20.13 718 25.11 22.75 1-1/4 16 21.50 920 27.50 25.00 1-1/4 20 23.88 2122 29.50 27.25 1-3/8 20 25.88 2624 32.00 29.50 1-3/8 20 28.13 31

*Also available manufactured in PVC, call customer service for information

IPS/DIPS Steel Blind Flanges for Pressure

• AWWA C207 Class D

Size[inch] Part No.

OD [inch]

T[inch]

Bolt Circle[inch]

Hole Dia.[inch] # of Holes

WPR [psi]

Weight (lbs)

2 6.00 0.625 4.75 3/4 4 175 53 7.50 0.625 6.00 3/4 4 175 84 9.00 0.625 7.50 3/4 8 175 126 11.00 0.688 9.50 7/8 8 175 188 13.50 0.688 11.75 7/8 8 175 2710 16.00 0.688 14.25 1 12 175 3812 19.00 0.812 17.00 1 12 175 6314 21.00 0.938 18.75 1-1/8 12 150 8916 23.50 1.000 21.25 1-1/8 16 150 11818 25.11 1.062 22.75 1-1/4 16 150 14020 27.50 1.125 25.00 1-1/4 20 150 18122 29.50 1.188 27.25 1-3/8 20 150 21324 32.00 1.250 29.50 1-3/8 20 150 27530 38.75 1.375 36.00 1-3/8 28 150 44436 46.00 1.625 42.75 1-5/8 32 150 73542 53.00 1.750 49.50 1-5/8 36 150 108548 59.50 1.750 56.00 1-5/8 44 150 1369


Flange Backup Rings

IPS Flange Backup Rings - Ductile Iron

• Designed Specifically for use with HDPE Flange Adapters • Approvals: ASME/ANSI B16.5, B16.47 Ser.A, CL150, B16.1, CL125, AWWA C207 (B/D/E)

Size[inch] Part No.

T [inch]

OD [inch]

ID [inch]

Bolt Circle[inch]

Hole Dia.[inch]

# of Holes

WPR [psi]

Weight (lbs)

3/4 0.53 3.88 1.11 2.75 5/8 4 335 1.01 0.53 4.25 1.38 3.13 5/8 4 335 1.21-1/4 0.63 4.63 1.72 3.50 5/8 4 335 1.51-1/2 0.69 5.00 1.97 3.88 5/8 4 335 1.62 0.75 6.00 2.50 4.69 3/4 4 335 2.73 0.94 7.50 3.63 6.00 3/4 4 335 4.54 0.94 9.00 4.63 7.50 3/4 8 335 5.55 0.94 10.00 5.69 8.50 7/8 8 335 5.96 1.00 11.00 6.75 9.50 7/8 8 335 7.58 1.13 13.50 8.75 11.75 7/8 8 335 12.010 1.19 16.00 10.94 14.25 1 12 335 15.012 1.25 19.00 13.00 17.00 1 12 200 24.012 1.50 19.00 13.00 17.00 1 12 335 25.014 1.38 21.00 14.38 18.75 1-1/8 12 200 29.014 1.63 21.00 14.38 18.75 1-1/8 12 335 35.016 1.63 23.50 16.19 21.25 1-1/8 16 200 39.016 1.84 23.50 16.19 21.25 1-1/8 16 335 48.018 1.70 25.00 18.38 22.75 1-1/4 16 200 42.018 2.00 25.00 18.38 22.75 1-1/4 16 335 53.020 1.84 27.50 20.38 25.00 1-1/4 20 200 57.020 2.23 27.50 20.38 25.00 1-1/4 20 335 70.022 2.41 29.50 22.38 27.25 1-3/8 20 335 80.024 2.16 32.00 24.38 29.50 1-3/8 20 200 80.024 2.56 32.00 24.38 29.50 1-3/8 20 335 103.026 2.50 34.25 26.38 31.75 1-3/8 24 250 109.028 2.59 36.50 28.38 34.00 1-3/8 28 250 130.030 2.28 38.75 30.38 36.00 1-3/8 28 130 118.030 2.47 38.75 30.38 36.00 1-3/8 28 200 139.032 2.56 41.75 32.38 38.50 1-5/8 28 200 165.034 2.88 43.75 34.38 40.50 1-5/8 32 200 191.036 2.75 46.00 36.38 42.75 1-5/8 32 130 193.036 3.00 46.00 36.38 42.75 1-5/8 32 200 214.042 3.25 53.00 42.38 49.50 1-5/8 36 130 265.048 3.63 59.50 48.50 56.00 1-5/8 44 100 354.054 4.03 66.25 54.62 62.75 1-7/8 44 100 519.0


DIPS Flange Backup Rings - Ductile Iron


Size[inch] Part No.

T [inch]

OD [inch]

ID [inch]

Bolt Circle[inch]

Hole Dia.[inch]

# of Holes

WPR [psi]

Weight (lbs)

4 0.94 9.00 4.90 7.50 3/4 8 335 56 1.00 11.00 7.00 9.50 7/8 8 335 88 1.13 13.50 9.19 11.75 7/8 8 335 1110 1.19 16.00 11.25 14.25 1 12 335 1612 1.50 19.00 13.38 17.00 1 12 335 2614 1.63 21.00 15.49 18.75 1-1/8 12 335 3116 1.84 23.50 17.59 21.25 1-1/8 16 335 4218 2.00 25.00 19.70 22.75 1-1/4 16 335 5120 2.23 27.50 21.85 25.00 1-1/4 20 335 6124 2.56 32.00 26.05 29.50 1-3/8 20 335 9430 2.88 38.75 32.25 36.00 1-3/8 28 250 142

IPS Flange Backup Rings - Stainless Steel


Size[inch] Part No.

T [inch]

OD [inch]

ID [inch]

Bolt Circle[inch]

Hole Dia.[inch]

# of Holes

WPR [psi]

Weight (lbs)

2 0.75 6.00 2.50 4.69 3/4 4 335 2.63 0.94 7.50 3.63 6.00 3/4 4 335 4.84 0.94 9.00 4.63 7.50 3/4 8 335 5.96 1.00 11.00 6.75 9.50 7/8 8 335 88 1.13 13.50 8.75 11.75 7/8 8 335 1310 1.19 16.00 10.94 14.25 1 12 335 1612 1.50 19.00 13.00 17.00 1 12 335 2714 1.38 21.00 14.38 18.75 1-1/8 12 200 3116 1.63 23.50 16.38 21.25 1-1/8 16 200 4218 1.70 25.00 18.38 22.75 1-1/4 16 200 4620 1.84 27.50 20.38 25.00 1-1/4 20 200 5822 2.41 29.50 22.38 27.25 1-3/8 20 335 6924 2.16 32.00 24.38 29.50 1-3/8 20 250 8726 2.50 34.25 26.38 31.75 1-3/8 24 250 N/A28 2.59 36.50 28.38 34.00 1-3/8 28 250 N/A30 2.47 38.75 30.38 36.00 1-3/8 28 200 N/A32 2.56 41.75 32.38 38.50 1-5/8 28 200 N/A34 2.88 43.75 34.38 40.50 1-5/8 32 200 N/A36 2.75 46.00 36.38 42.75 1-5/8 32 200 N/A42 3.25 53.00 42.38 49.50 1-5/8 36 130 N/A48 3.63 59.50 48.50 56.00 1-5/8 44 100 N/A54 4.03 66.25 54.62 62.75 1-7/8 44 100 N/A


DIPS Flange Backup Rings - Stainless Steel


Size[inch] Part No.

T [inch]

OD [inch]

ID [inch]

Bolt Circle[inch]

Hole Dia.[inch]

# of Holes

WPR [psi]

Weight (lbs)

4 0.94 9.00 4.90 7.50 3/4 8 335 5.46 1.00 11.00 7.00 9.50 7/8 8 335 7.58 1.13 13.50 9.19 11.75 7/8 8 335 1210 1.19 16.00 11.25 14.25 1 12 335 1512 1.50 19.00 13.38 17.00 1 12 335 2714 1.38 21.00 15.49 18.75 1-1/8 12 200 3016 1.63 23.50 17.59 21.25 1-1/8 16 200 4118 1.70 25.00 19.70 22.75 1-1/4 16 200 4520 1.84 27.50 21.85 25.00 1-1/4 20 200 5724 2.16 32.00 26.05 29.50 1-3/8 20 200 86


IPS Flange Backup Rings - Epoxy Coated


Size[inch] Part No.

T [inch]

OD [inch]

ID [inch]

Bolt Circle[inch]

Hole Dia.[inch]

# of Holes

WPR [psi]

Weight (lbs)

3/4 0.53 3.88 1.11 2.75 5/8 4 335 1.01 0.53 4.25 1.38 3.13 5/8 4 335 1.21-1/4 0.63 4.63 1.72 3.50 5/8 4 335 1.51-1/2 0.69 5.00 1.97 3.88 5/8 4 335 1.62 0.75 6.00 2.50 4.69 3/4 4 335 2.73 0.94 7.50 3.63 6.00 3/4 4 335 4.54 0.94 9.00 4.63 7.50 3/4 8 335 5.55 0.94 10.00 5.69 8.50 7/8 8 335 5.96 1.00 11.00 6.75 9.50 7/8 8 335 7.58 1.13 13.50 8.75 11.75 7/8 8 335 12.010 1.19 16.00 10.94 14.25 1 12 335 15.012 1.25 19.00 13.00 17.00 1 12 200 24.012 1.50 19.00 13.00 17.00 1 12 335 25.014 1.38 21.00 14.38 18.75 1-1/8 12 200 29.014 1.63 21.00 14.38 18.75 1-1/8 12 335 35.016 1.63 23.50 16.19 21.25 1-1/8 16 200 39.016 1.84 23.50 16.19 21.25 1-1/8 16 335 48.018 1.70 25.00 18.38 22.75 1-1/4 16 200 42.018 2.00 25.00 18.38 22.75 1-1/4 16 335 53.020 1.84 27.50 20.38 25.00 1-1/4 20 200 57.020 2.23 27.50 20.38 25.00 1-1/4 20 335 70.022 2.41 29.50 22.38 27.25 1-3/8 20 335 80.024 2.16 32.00 24.38 29.50 1-3/8 20 200 80.024 2.56 32.00 24.38 29.50 1-3/8 20 335 103.026 2.50 34.25 26.38 31.75 1-3/8 24 250 109.028 2.59 36.50 28.38 34.00 1-3/8 28 250 130.030 2.28 38.75 30.38 36.00 1-3/8 28 130 118.030 2.47 38.75 30.38 36.00 1-3/8 28 200 139.032 2.56 41.75 32.38 38.50 1-5/8 28 200 165.034 2.88 43.75 34.38 40.50 1-5/8 32 200 191.036 2.75 46.00 36.38 42.75 1-5/8 32 130 193.036 3.00 46.00 36.38 42.75 1-5/8 32 200 214.042 3.25 53.00 42.38 49.50 1-5/8 36 130 265.048 3.63 59.50 48.50 56.00 1-5/8 44 100 354.054 4.03 66.25 54.62 62.75 1-7/8 44 100 519.0


DIPS Flange Backup Rings - Epoxy Coated


Size[inch] Part No.

T [inch]

OD [inch]

ID [inch]

Bolt Circle[inch]

Hole Dia.[inch]

# of Holes

WPR [psi]

Weight (lbs)

4 0.94 9.00 4.90 7.50 3/4 8 335 56 1.00 11.00 7.00 9.50 7/8 8 335 88 1.13 13.50 9.19 11.75 7/8 8 335 1110 1.19 16.00 11.25 14.25 1 12 335 1612 1.50 19.00 13.38 17.00 1 12 335 2614 1.63 21.00 15.49 18.75 1-1/8 12 335 3116 1.84 23.50 17.59 21.25 1-1/8 16 335 4218 2.00 25.00 19.70 22.75 1-1/4 16 335 5120 2.23 27.50 21.85 25.00 1-1/4 20 335 6124 2.56 32.00 26.05 29.50 1-3/8 20 335 9430 2.88 38.75 32.25 36.00 1-3/8 28 250 142


IPS Flange Backup Rings - Galvanized


Size[inch] Part No.

T [inch]

OD [inch]

ID [inch]

Bolt Circle[inch]

Hole Dia.[inch]

# of Holes

WPR [psi]

Weight (lbs)

3/4 0.53 3.88 1.11 2.75 5/8 4 335 1.01 0.53 4.25 1.38 3.13 5/8 4 335 1.21-1/4 0.63 4.63 1.72 3.50 5/8 4 335 1.51-1/2 0.69 5.00 1.97 3.88 5/8 4 335 1.62 0.75 6.00 2.50 4.69 3/4 4 335 2.73 0.94 7.50 3.63 6.00 3/4 4 335 4.54 0.94 9.00 4.63 7.50 3/4 8 335 5.55 0.94 10.00 5.69 8.50 7/8 8 335 5.96 1.00 11.00 6.75 9.50 7/8 8 335 7.58 1.13 13.50 8.75 11.75 7/8 8 335 12.010 1.19 16.00 10.94 14.25 1 12 335 15.012 1.25 19.00 13.00 17.00 1 12 200 24.012 1.50 19.00 13.00 17.00 1 12 335 25.014 1.38 21.00 14.38 18.75 1-1/8 12 200 29.014 1.63 21.00 14.38 18.75 1-1/8 12 335 35.016 1.63 23.50 16.19 21.25 1-1/8 16 200 39.016 1.84 23.50 16.19 21.25 1-1/8 16 335 48.018 1.70 25.00 18.38 22.75 1-1/4 16 200 42.018 2.00 25.00 18.38 22.75 1-1/4 16 335 53.020 1.84 27.50 20.38 25.00 1-1/4 20 200 57.020 2.23 27.50 20.38 25.00 1-1/4 20 335 70.022 2.41 29.50 22.38 27.25 1-3/8 20 335 80.024 2.16 32.00 24.38 29.50 1-3/8 20 200 80.024 2.56 32.00 24.38 29.50 1-3/8 20 335 103.026 2.50 34.25 26.38 31.75 1-3/8 24 250 109.028 2.59 36.50 28.38 34.00 1-3/8 28 250 130.030 2.28 38.75 30.38 36.00 1-3/8 28 130 118.030 2.47 38.75 30.38 36.00 1-3/8 28 200 139.032 2.56 41.75 32.38 38.50 1-5/8 28 200 165.034 2.88 43.75 34.38 40.50 1-5/8 32 200 191.036 2.75 46.00 36.38 42.75 1-5/8 32 130 193.036 3.00 46.00 36.38 42.75 1-5/8 32 200 214.042 3.25 53.00 42.38 49.50 1-5/8 36 130 265.048 3.63 59.50 48.50 56.00 1-5/8 44 100 354.054 4.03 66.25 54.62 62.75 1-7/8 44 100 519.0


DIPS Flange Backup Rings - Galvanized


Size[inch] Part No.

T [inch]

OD [inch]

ID [inch]

Bolt Circle[inch]

Hole Dia.[inch]

# of Holes

WPR [psi]

Weight (lbs)

4 0.94 9.00 4.90 7.50 3/4 8 335 56 1.00 11.00 7.00 9.50 7/8 8 335 88 1.13 13.50 9.19 11.75 7/8 8 335 1110 1.19 16.00 11.25 14.25 1 12 335 1612 1.50 19.00 13.38 17.00 1 12 335 2614 1.63 21.00 15.49 18.75 1-1/8 12 335 3116 1.84 23.50 17.59 21.25 1-1/8 16 335 4218 2.00 25.00 19.70 22.75 1-1/4 16 335 5120 2.23 27.50 21.85 25.00 1-1/4 20 335 6124 2.56 32.00 26.05 29.50 1-3/8 20 335 9430 2.88 38.75 32.25 36.00 1-3/8 28 250 142



General Terms and Conditions of SaleGF Piping Systems USA Terms and Conditions (Rev. 12/2015) supersede all previous Terms and Conditions for Georg Fischer LLC, Georg Fischer Sloane LLC, and Georg Fischer Harvel LLC.

It is the responsibility of the Distributor, Dealer, or Agent to provide a current copy of these Terms and Conditions to the Consumers of Georg Fischer Piping products.

Acceptance of Terms and ConditionsAcceptance by Customer of GF Piping Systems USA, (hereinafter “Seller”) offer of Products for sale is hereby expressly conditioned upon Customer’s acceptance of these General Terms and Conditions of Sale and these General Terms and Conditions of Sale will be deemed accepted, as written, despite any language in Customer’s purchase order and/or other documentation which is either conflicting or supplemental, unless promptly after this offer, Customer specifically advises Seller of each term and condition not so accepted and Seller accepts Customer’s conflicting and/or supplemental term(s) in writing.

Order AcceptanceSeller reserves the right to accept or reject any order. Possession of a price list by Customer does not constitute an offer to sell.

Credit Approval and Minimum Order ChargeCustomer credit approval is required prior to any shipment.

The minimum order is $100 net.

List Price, Discount or Freight ChargesList prices, discount, and freight terms are subject to change without notice. All prices are F.O.B. Seller’s factory or authorized warehouse at Seller’s discretion.

Payment Terms2% 15 days, net 30, from date the invoice is issued unless otherwise stated in a specific quotation. No unauthorized deductions allowed, such as deductions for pending Return Material Transac-tions that are subject to review. Seller reserves the right to apply a finance charge to the balance of any past-due invoice (over 30 days from date of invoice) at a rate of 1.5% per month, 18% per annum. Payment terms on fusion machine rentals net 30; see rental agreement for more details.

TaxesSeller charges Customer for all sales, excise and other taxes and governmental charges Seller is required to collect from Customer. Customers claiming exemption must furnish documenta-tion required by law which is satisfactory to Seller to permit Seller to refrain from collecting such charges.

WARRANTY AND LIMITATIONSSeller's Products are carefully inspected for manufacturing defects; however, it is not always possible to detect hidden defects.

Seller warrants that its products shall conform to the description of such products as provided to Customer by Seller through Seller's catalog, analytical data or other literature. THIS WARRANTY IS EXCLUSIVE, AND SELLER MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE OR COURSE OF DEALING OR USAGE OF TRADE – WHICH ARE HEREBY DISCLAIMED. Seller's warranties made in connection with this sale shall not be effective if Seller has determined, in its sole discretion, that Customer has misused the products in any manner, has failed to use the products in accordance with industry standards and practices, or has failed to use the products in accordance with instructions, if any, furnished by Seller. Seller does not warrant any Products obtained through an unauthorized Distributor, Dealer, or Agent.

LIMITATIONS OF REMEDY Seller's sole and exclusive liability and Customer’s exclusive remedy with respect to products proved to Seller's satisfaction to be defective or nonconforming shall be repair or replacement of such products without charge or refund of the purchase price, in Seller's sole discretion, upon the return of such products in accordance with Seller's instructions. SELLER SHALL NOT IN ANY EVENT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY KIND RESULTING FROM ANY USE OR FAILURE OF THE PRODUCTS, EVEN IF SELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE INCLUDING, WITHOUT LIMITATION, LIABILITY FOR LOSS OF USE, LOSS OF WORK IN PROGRESS, DOWN TIME, LOSS OF REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS, LOSS OF PRODUCTS OF CUSTOMER OR OTHER USE OR ANY LIABILITY OF CUSTOMER TO A THIRD PARTY ON ACCOUNT OF SUCH LOSS, OR FOR ANY LABOR OR ANY OTHER EXPENSE, DAMAGE OR LOSS OCCASIONED BY SUCH PROD-UCT INCLUDING PERSONAL INJURY OR PROPERTY DAMAGE. Any and all claims of Customer against Seller must be brought within one (1) year of Seller’s tender of delivery, regardless of their nature.

Order Changes or CancellationsCancellation or modifications of orders may be possible only with prior written consent from Seller. Since all orders are individually entered for processing immediately upon receipt, Seller reserves the right to charge back to the Customer costs incurred from either order cancellation or order modification. Seller also reserves the right to consider all order additions as new orders and subject to all terms and conditions.

Seller will not cancel orders for custom or non-cancelable products if Seller has already pro-duced the product or incurred expenses toward producing the product at the time the Customer seeks to cancel.

DeliverySeller disclaims liability for consequential damages from late deliveries unless seller assumes liability for such damages in writing when the order is placed. Further, Seller disclaims liability where delivery delays caused by strike, differences with workmen, or causes beyond Seller’s con-trol, including but not limited to fires, floods, accidents, government actions, shortages of labor, raw materials, production facilities, or transportation. Where delivery delays are caused by labor problems, Seller is not obligated to seek or obtain any settlement which, in Seller’s judgment, is not in Seller’s best interest.

Standard PackagingSeller will accept orders from Customer exclusively in multiples of the standard packaging quantity or boxed quantity. Seller reserves the right to reject any order that is not a standard packaging or boxed quantity of a Product.

Freight Continental US – Full freight will be paid on the following orders:1. Pipe $7,500 net or greater in one of the following categories:

Combination of products from one shipping point to meet freight allowance is at the sole discretion of the seller.

2. Fittings, Valves, & Actuation $1,500 net or greaterFreight allowed orders will be sent by a designated carrier of Seller’s choice. Additional charges will be invoiced to Customer for special handling and air freight when requested. Standard Pipe lengths require long truck beds for shipping and may be shipped separately from valves and/or fittings purchased on the same order. Valves and/or fittings will be shipped using practical shipping methods.

Freight will not be paid on the following orders:

Unless otherwise specified, shipments are surface, prepaid and added to invoice.

Mode of Shipment and PackagingSeller reserves the right to ship orders in the most economical manner, as long as the product is shipped on or before the promised ship date. If product ships after the promised ship date, Seller may automatically adjust the shipping method to help improve delivery of the delayed shipment, at no additional cost.

If Seller pays freight, Seller may hold shipment until all items become available. Customer bears extra cost of non-standard packaging or handling requested by Customer.

Transfer of OwnershipAll products are FOB Seller’s facility and title of merchandise transfers when product is loaded onto carrier. Claims for damaged merchandise should be made to carrier by Customer.Assignment. Customer may not assign its rights under or interest in any purchase order without the prior written consent of Seller. These terms and conditions of sale shall be binding upon and inure to the benefit of Customer and Seller, their successors and permitted assigns.

Technical Documentation and Intellectual Property. Unless specified otherwise, technical docu-ments such as drawings, descriptions, illustrations and the like, constitute only an approximate guide. Seller reserves the right to make any changes considered necessary. Seller expressly reserves any and all intellectual property rights therein.

Non-Conforming ShipmentsCustomer must notify Seller in writing within 7 days after receipt of shipments not conforming with Customer’s order, stating specifically Customer’s claim of non-conformity, or Customer is deemed to accept the shipment as is. If Seller is satisfied the shipment is non-conforming, Seller will (i) credit Customer for the price of defective goods or goods shipped but not ordered (including allocated outbound and return freight) upon return of goods; (ii) promptly ship omitted items waiving Seller’s new order charges. Customer is required to make timely payment to Seller of any amount which is undisputed or not subject to such claims.

Return of Goods for CreditSeller accepts returns of certain Engineered Piping Products, Valve and Actuation Products, Signet Instrumentation Products, Waste and Containment Products, and Vinyl Piping Products for a standard restock charge of 25%. Pipe is not returnable. Products denoted with a caret (^) symbol in front of the part number in the current Master Distributor Price List have a 40% restock and products denoted with an asterisk (*) symbol are non-cancelable/non-returnable. Only products purchased within the past twelve (12) months, in original “like new” packaging (full carton quantities), of current design, and listed in the current Master Distributor Price List shall be considered for returns. All products qualifying for return are subject to review for market-ability (quantities in question in relationship to historical stock movement) before issuance of a Return Material Authorization (RMA) number. Returns due to Seller’s product warranty or order entry/shipping error will not be charged a restock fee.

Product for credit consideration should be returned to Seller’s originating location. All returns are subject to inspection upon receipt. No credit will be issued until the returned material has been inspected, accepted, and processed. Customers will be contacted if quantity differences and/or non-acceptable material are found during inspection. Any credit issued will reflect only quantities actually received and accepted by Seller.

Disposition (return to Customer or scrap) of returned product not accepted back by Seller must be provided by Customer within 10 business days, otherwise it will be subject to disposal. All ma-terial returns must be accompanied by a valid Return Material Authorization (RMA) number. RMA numbers may be obtained from the Customer Service Department. When requesting a RMA, the original purchase order number and date of purchase must be provided.

All material returns must be received within thirty (30) days of the RMA issuance.

All material returns must be shipped freight prepaid. No collect shipments will be accepted by Seller. Restock charges and prepaid freight do not apply to warranty defective merchandise or returns due to Seller order entry or shipping errors.

Return of Goods for Warranty EvaluationWhen requesting a RMA for material evaluation, Customer must first complete and submit a Material Safety Disclosure sheet and Request For Evaluation form obtained from Customer Service. Material arriving to Seller without a valid RMA number will be returned to the customer/distributor, freight col-lect. RMA numbers must be clearly referenced on all shipping documents and shipping containers.

Rev. 12/2015

Always check for the most current General Terms and Conditions and Warranty Statement at www.gfpiping.com under "Price Lists."

1. Signet Product2. Custom Products3. Heat Exchangers4. PVC and CPVC Fabricated Fittings 14"

and larger5. Fuseal Squared, Tanks and Accessories,

and Special Fabrications

6. Fuseal Large Diameter: 8”, 10”, 12” Pipe and Fittings

7. COOL-FIT ABS Lite Pipe8. Double-See9. International Orders10. Fusion Machines and Accessories

a. PPro-Sealb. Contain-Itc. Fuseal (1½"–6")d. SYGEFe. PROGEF

f. PVC and CPVC, including shapes and rods

g. PVC and CPVC, metrich. Ducti. CTS

j. LXTk. Blazemasterl. PE 100m. COOL-FIT ABSn. COOL-FIT ABS Plus

Pre-insulated

GF Piping Systems

39605 Independence Avenue, Shawnee, OK 74804Tel. (405) 273-6302, Toll Free (800) 654-3872, Fax (405) 878-4904 e-mail: [email protected]

Argentina / Southern South AmericaGeorg Fischer Central Plastics Sudamérica S.R.L.Buenos Aires, ArgentinaPhone +5411 4512 02 [email protected]

AustraliaGeorge Fischer Pty LtdRiverwood NSW 2210 AustraliaPhone +61(0)2 9502 8000 [email protected]

Austria Georg Fischer Rohrleitungssysteme GmbH3130 HerzogenburgPhone +43(0)2782 856 [email protected]

Belgium / LuxembourgGeorg Fischer NV/SA1070 Bruxelles/BrüsselPhone +32(0)2 556 40 [email protected]

BrazilGeorg Fischer Sist. de Tub. Ltda.04795-100 São PauloPhone +55(0)11 5525 [email protected]

CanadaGeorg Fischer Piping Systems LtdMississauga, ON L5T 2B2Phone +1(905)670 8005Fax +1(905)670 [email protected]

ChinaGeorg Fischer Piping Systems Ltd Shanghai 201319Phone +86(0)21 3899 3899 [email protected]

Denmark / IcelandGeorg Fischer A/S2630 TaastrupPhone +45 (0)70 22 19 [email protected]

FinlandGeorg Fischer AB01510 VANTAAPhone +358 (0)9 586 58 25 Fax +358 (0)9 586 58 [email protected]

FranceGeorg Fischer SAS95932 Roissy Charles de Gaulle CedexPhone +33(0)1 41 84 68 [email protected]

GermanyGeorg Fischer GmbH73095 Albershausen Phone +49(0)7161 [email protected]

IndiaGeorg Fischer Piping Systems Ltd400 076 MumbaiPhone +91 224007 [email protected]

ItalyGeorg Fischer S.p.A.20063 Cernusco S/N (MI)Phone +3902 921 [email protected]

JapanGeorg Fischer Ltd556-0011 Osaka, Phone +81(0)6 6635 [email protected]

KoreaGeorg Fischer Piping Systems271-3 Seohyeon-dong Bundang-guSeongnam-si, Gyeonggi-doSeoul 463-824Phone +82 31 8017 1450Fax +82 31 8017 [email protected]

MalaysiaGeorge Fischer (M) Sdn. Bhd.40460 Shah Alam, Selangor Darul EhsanPhone +60 (0)3 5122 [email protected]

Mexico / Northern Latin AmericaGeorg Fischer S.A. de C.V.Apodaca, Nuevo LeonCP66636 MexicoPhone +52 (81)1340 8586Fax +52 (81)1522 [email protected]

Middle EastGeorg Fischer Piping Systems (Switzerland) Ltd.Dubai, United Arab EmiratesPhone +971 4 289 49 [email protected]

NetherlandsGeorg Fischer N.V.8161 PA EpePhone +31(0)578 678 222 [email protected]

New ZealandGeorg Fischer Ltd13 Jupiter Grove, Upper Hutt 5018PO Box 40399, Upper Hutt 5140Phone +64(0)4 527 [email protected]/nz

NorwayGeorg Fischer AS1351 Rud Phone +47(0)67 18 29 [email protected]

PolandGeorg Fischer Sp. z o.o.05-090 Sekocin Nowy Phone +48(0)22 31 31 0 50 [email protected]

RomaniaGeorg Fischer Piping Systems (Switzerland) Ltd.020257 Bucharest - Sector 2Phone +40(0)21 230 53 [email protected]

RussiaGeorg Fischer Piping Systems (Switzerland) Ltd.Moscow 125047Tel. +7 495 258 60 [email protected]

SingaporeGeorge Fischer Pte Ltd11 Tampines Street 92, #04-01/07528 872 SingaporePhone +65 6747 [email protected]

Spain / PortugalGeorg Fischer S.A.28046 MadridPhone +34(0)91 781 98 [email protected]

SwedenGeorg Fischer AB117 43 StockholmPhone +46(0)8 506 775 [email protected]

SwitzerlandGeorg Fischer Rohrleitungssysteme (Schweiz) AG8201 SchaffhausenPhone +41(0)52 631 30 [email protected]

TaiwanGeorg Fischer Co., Ltd.San Chung Dist., New Taipei CityPhone +886 2 8512 2822Fax +886 2 8512 2823www.georgfischer.tw

United Kingdom / IrelandGeorge Fischer Sales LimitedCoventry, CV2 2STPhone +44(0)2476 535 [email protected]

USA / CaribbeanGeorg Fischer LLCTustin, CA 92780-7258Phone +1(714) 731 88 00 Toll Free 800 854 40 [email protected]

VietnamGeorge Fischer Pte Ltd136E Tran Vu, Ba Dinh District, HanoiPhone +84 4 3715 3290 Fax +84 4 3715 3285

International Georg Fischer Piping Systems (Switzerland) Ltd.8201 Schaffhausen/SwitzerlandPhone +41(0)52 631 30 03Fax +41(0)52 631 28 [email protected]

www.gfps.com

The technical data is not binding. They neither constitute expressly warranted characteristics nor guaranteed properties nor a guaranteed durability. They are subject to modification. Our General Terms of Sale apply.

Date post:	10-Aug-2020
Category:	Documents
Upload:	others
View:	2 times
Download:	1 times

GF Piping Systems GF Central Plastics 2016 Fabricated Fittings … · 2020-08-03 · GF Piping...

Documents