P RO V ISION GMV GMV PROVISION is a new product from GMV, which is designed to be used in the modernisation of existing hydraulic lifts. The product is a completely assembled unit combined of a GMV tank unit, GEV valve in combination with our manufacturing partner Kinds specifically designed controller KI-Line Vision. The unit can be used in modernisation of most of the lifts in the market existing make such as Kone, Deve, IGV and previous version of GMV. GMV PROVISION will improve the ride quality and result in a higher accuracy in floor levelling to make it easier for disabled people to enter the lift and to fulfil the code EN 81-80. Updated technology with minor investment Your provider of lifts and liftcomponents 0,6 0,6 5 10 15 0,6 0,6 Velocity (m/s) Velocity (m/s) Time (s) More comfort Less travel time Time (s) Traditional valve GEV valve Up Down 5 10 15 Motor Pump Jack : 7,7 kW : 125 l/min : 90 mm Motor Pump Jack : 9,5 kW : 125 l/min : 90 mm Traditional GEV
Transcript
ProVisionGMV
GMV ProVision is a new product from GMV, which is designed to be used in the modernisation of existing hydraulic lifts. The product is a completely assembled unit combined of a GMV tank unit, GEV valve in combination with our manufacturing partner Kinds specifically designed controller KI-Line Vision.
The unit can be used in modernisation of most of the lifts in the market existing make such as Kone, Deve, IGV and previous version of GMV.
GMV ProVision will improve the ride quality and result in a higher accuracy in floor levelling to make it easier for disabled people to enter the lift and to fulfil the code EN 81-80.
Updated technology with minor investment
Your provider of lifts and liftcomponents
0,6
0,6
5 10 15
0,6
0,6
Velocity(m/s)
Velocity(m/s)
Time (s)
More comfort
Less travel time
Time (s)
Traditional valveGEV valve
Up Down
5 10 15
MotorPumpJack
: 7,7 kW: 125 l/min: 90 mm
MotorPumpJack
: 9,5 kW: 125 l/min: 90 mm
Traditional
GEV
GMV Sweden AB Box 19, Forsdalavägen 1, 342 21 ALVESTA, SWEDEN | www.gmv.se
Improved ride quality with the GMV electronic regu-•lated valve GEV.
Improved levelling of the lift.•
Reduced noise levels. •
Reduced power installed and lower energy consumption. •
Controller equipped with faults in clear wording.•
The fault log can be sent by email, SMS or controlled •on the webb.
Push buttons and indicators adapted to its purpose.•
Fulfills the new code EN 81- 70 and EN 81-80. •
Technical specificationThe unit has the following advantages for the end user
Pump unit has a pump size ranging from 75 and up •to 210 l/min.
Motor has a effect ranging from 4,7 kW up to •18,4 kW in 400/690 V 50 Hz.
”Soft start” for motor.•
Tank type F1 or T2 with fluid volume from 50 to •220 litre.
Electronic regulated valve GEV with feedback via a •encoder in the shaft.
Automatic emergency lowering to floor level in the •event of a power failure.
Double safety protecting of involuntary movement from •floor level according to new code EN 81-2 A3.
Controller is designed for up to 12 floor, 12 door, •2 entrances.
Direct call or collective (down or full collective) •
Controller communicates with the landing door and •the cabin via a data bus.
”Encoder” connected to the cabin measures the •position and the speed of the lift.
Lift speed up to 1 m/s (30% higher down speed can •be used to save energy)
Pushbutton panel with integrated emergency •telephone and pictogram according to EN 81-70.
Emergency telephone for continues contact to alarm •central via fixed line (GSM as option)
GMV ProVision is fully adjusted and tested before delivery to make the installation set up and testing as easy and time saving as possible.
