Government of Jammu and Kashmir. Directorate of Technical Education J&K Srinagar.
NOTICE INVITING TENDERS ( NATIONAL COMPETATIVE BIDDING)
For and on behalf of the Governor of Jammu & Kashmir State, Sealed tenders affixed with five rupees revenue stamp are invited from registered / reputed Manufacturers / their authorized dealers / Suppliers / firms for supply of the Machinery Equipment etc. for the various ITIs , women wings, under Prime Ministers Re-Construction Plan, Centrally Sponsored Schemes and other normal Plan / Non-Plan schemes of the J&K State, on the following terms & conditions as per Annexure ( “A” to “P”) of this NIT, which should reach to the Office of the undersigned by or before 26-11-2007 upto 2.00PM. TERMS & CONDITIONS:-
1) The rates be quoted only against the specified item, no rates for alternative items shall be quoted.
2) The Tenders downloaded from our official web site shall append Rs. 300/= as cost of tender documents at the time of deposit in addition to earnest money.
3) The Tender document should be addressed to the :-
DIRECTOR TECHNICAL EDUCATION NEAR; GOVT POLYTECHNIC, BIKRAM CHOWK, J&K , JAMMU.
4) The Tender should be sent either under sealed registered cover or deposited in the Office of the undersigned duly marked “Tender for Machinery Equipment etc.” on or before 26.11.2007 upto 2.00 PM.
5) The Tender must be complete in all respects. All the terms and conditions of tender including Technical specifications should be carefully studied for the sake of complete and comprehensive offer. No other condition except those mentioned herein will be entertained in the Tender.
6) Each Offer / Tender shall be accompanied with a Call Deposit Receipt of Rupees TWENTY THOUSAND ONLY ( Rs.20000/=) for each group, from any scheduled bank pledged to the Accounts Officer, Directorate of Technical Education J&K Srinagar. No cheque or Bank Draft in lieu of call deposit receipt shall be accepted in any case. This condition shall in no case be waived of except where Machinery and Equipments asked for are exempted by the Industries Department of the State / National Small Industries (NSIC) New Delhi.
7) The successful Tenderer shall have to execute an agreement with
Government within 15 days after acceptance of the Tender is communicated to him. Failure to execute such an agreement shall not prevent the terms and conditions embodied herein being enforced against him and any loss sustained by the Government in re-tendering shall be recovered from him besides forfeiture of the security deposit.
8) The rates should be clearly quoted both in Words and figures and
without any cuttings / erasing/ overwritings. No such rates wherein any cuttings / erasing/ overwritings is / are found will be considered for comparison. The Tender should be typed or written in ink and should be legible. Any quotations written in pencil shall be rejected.
9) In case of any doubt , dispute, difference, questions arising between
Tender and Department regarding incorporation of any of the terms and Conditions of the NIT or any matter connected or incidentals here to or the respective right and responsibility of the parities , the same shall be referred to the Commissioner / Secretary to Govt, Higher and Technical Education Department, J&K, or any other person nominated by him in this behalf for arbitration. His decision in the matter shall be final, conclusive and binding on the parties.
10) Time is the essence of the contract. In the event of failure or default on
the part of the Tenderers on the fulfillment of any of the terms and conditions embodied herein or in the event of his failure to supply the ordered equipment etc. within time fixed from the date of dispatch of the supply order, the Director Technical Education shall without any prejudice to its claims and remedies available to him / her under any law be competent to forfeit the Earnest Money in whole or in part or to terminate the contract after 30 days notice to the Tenderer or impose such penalty as may be determined by the Director.
11) In case, the Supplier / Manufacturer / Distributor / Authorized Dealer
etc. fails to supply the ordered Equipment in full, penalty of 2% ( Two percent ) of the total cost of the order shall be imposed upon him / them.
12) The supplier has to deliver the goods within 04 weeks time from the date of issue of supply order. This can be altered depending upon the requirement of the Department.
13) Offers should be supported by visuals, pamphlets and relevant
literature. Samples will be sought if and where felt necessary, and the same should be kept in readiness, so that same can be provided to the Directorate, when asked, within a period of 7 (Seven) days.
14) Rates should be strictly quoted inclusive of all Taxes ( VAT, Entry Tax if any, other taxes etc) freight, levies applicable at the time of supplies and quoted F.O.R. Srinagar / Jammu.
15) The Director, Technical Education ,J&K reserves the right to accept or
reject any tender or part thereof without assigning any reason / reasons thereof.
16) Rates shall remain valid for a period of One year between 01-11-2007
to 31-10-2008.
17) The successful bidder shall have to provide training to the identified
Officials of the Department at Srinagar and Jammu, where applicable .
18) The vendor shall to give warranty of Two years, in addition to it he has to provide three years after sale service free of cost including warranty period.
19) The Supplier has to furnish the Tax clearance Certificate in the
prescribed form issued by the Assigning Authority concerned before entertaining a tender for supply of Goods.
20) The successful Tenderer shall have to furnish Security Deposit equivalent to 2% of supplied value of Goods in the form of Bank Guarantee of Two Years from any Nationalized Bank pledged to Accounts Officer , directorate of Technical education, J&K. such Bank Guarantee shall be furnished within One month from the Date of issue of Supply Order. This would be in addition to CDR’s.
21) At the time of procurement if DGS&D rates are available for any
item the Director reserves the exclusive right to procure the same on the rate contract & exclude the item from the tender. In that case no tenderer has any claim whatsoever over the said item.
22) The quantity mentioned in the Annexures is subjected to minor variations, as undersigned being the Chairman, is competent to make the necessary changes.
No:- DTE/ Pur/2007-08/ 496-I/343-44 Dated:- 19-10-2007.
Sd/- ( Syed Mohammad Fazlullah) IAS
Director, Technical Educat
ANNEXURE ‘ A ’ OF DETAILED TENDER NOTICE NO: DTE/PUR/2007-08/ DATED: - /10-2007 List of of Machinery Equipment for the trade of Information Technology /COPA / Computer Servicing / Computer Hardware Mechanic / Software Application / Tourist Guide / Electronic Mechanic and Network Technician
S. NO.
Name of the items with specification.
Qty.
Rate per Unit.
Taxes.
Total.
01 Vacuum cleaner (1400 w ) 63
02 Bread board Trainer (DC power supply 5 v and 12 v-1Amp., Solder less 2520 Tie points, Logic input bounce less switches 8,LED status indicators 8, 1KHZ-100KHZ clock Fixed and Variable.
10
03 Frequency counter (10 hz to 300 MHz) 04
04. TTLIC tester (16 digit 7segement display,20&40 pin ZIF socket)Scientific make
03
05 In circuit tester 04
06 Logic probe(50 MHZ Frequency Range and Logic Pulser)
39
07 EHT probe ( 1-100 V) 07
08 Bar code reader 22
09 Microwave oven (Trainer) 16
10 Washing machine manual (Trainer) 03
11 Washing machine Automatic(Trainer) 04
12 Synthesizers 05
13 Colour TV set (different types) (Trainer type with Remote and without remote )
15
14 Video transmitter Trainer Type 07
15 Radio receiver AM/FM /SW [Trainer type ] 18
16 Two –In-One [Trainer type ] 15
17 Telephone (trainer type) 12
18 Cordless telephone (trainer type) 17
19 Modem (External Modem 64 Mbps with Interface connectors)
92
20 Satellite receiving System (Trainer type ) 05
21 EPROM programmer (handy serial programmer 14-40 pin)
04 each.
22 Analog trainer kit(variable DC 0 to 15 V fixed 5v -1 AMP )
09
23 Invertors for TV, Tubes light Fax, Epabx etc. and Trolley
28
24 ISDN Line (for internet) 03
25 Routers. 03
26 Fiber Optical Networking trainer 11
27 DAT with Media 03
28 Magnifier with light facility (OHP) 100w lamp air cooled
05
29 TVSS: - the main incoming switch board ( MSB) and distribution boards ( DB) shall be equipped with TVSS as defined in the IEEE standard 1100 (1990). The TVSS shall be constructed of metal oxide varistor ( MOV) technology and internal surge capacitors . The surge protective devices shall be sized per IEEE std. C62.41-1991 and IEEE Std. C62.45-1992. Surge protective devices used for three – phase , four wire circuits shall be connected in all combinations of line to line , line to neutral. Line to ground and neutral to ground ( L-L.L-N.L-G.N-G). The TVSS shall have a UL Listing and leveled 1449-2 suppressed voltage rating of 800 V peak. The unit shall have a maximum continuous operating voltage ( Mcove) rating of minimum 320 VRMS. etc
34
ANNEXURE ‘B’ DETAILED TENDER NOTICE NO: DTE/PUR/2007-08/
DATED: -10-2007
List of Equipment for Consumer Electronics Trade.
S.N Name of the items with specification. Qty. Rate per Unit.
Taxes. Total.
01 Function Generator Sine/Square wave 100 MHz
87
02 Commercial AM / FM receiver table top type- trainer
26
03 PA Amplifier 80/80 Watt with Mike, Speaker 16 Ohm
Coolum type Mike Stand and Mike Cable
45
04 Colour Pattern Generator Having
Pattern + RGB Display 30 to 800 MHz-S9144
24
05 TV Receiver Colour 21” Flatron.
58
06 Colour TV Demonstrator
14
07 Colour TV Camera Handy cam with DVD Driver
27
08 Basic Electronic Trainer
132
09 Linear IC Trainer
90
10 Digital IC Trainer
115
11 8085 Microprocessor Trainer Kit
75
12 VCR Trainer Type
65
13 Intercom System 14 port
19
14 Wobbulator 200 MHz
24
15 Telephone system Trainer
15
16 Overhead Projector 1000 W lamp with Screen 81
ANNEXURE ‘C’OF DETAILED TENDER NOTICE NO: DTE/PUR/2007-08/
DATED: -10-2007
MACHINERY EQUIPMENT OF MOTOR MECHANIC / DIESEL MECHANIC /DRIVER CUM MECAHNIC TRADE.
S.No. Name of Item . Qty. Rate per
Unit. Taxes. Total.
01. Fuel Pump ( Fuel Injection Pump 20
02 Distributor ( Three Cylinder) 18
03 Distributor ( Four Cylinder ) 16
04 Carburetor ( two different types) 15 each.
05. Water Pump and Oil Pump ( Ecnostat & double barrel Maruti type)
14 each.
06 Filling Jig for adjusting the piston ring gap. 12 each.
07 Jack, hydraulic Hi-lift type ( Trolley type ) 12
08 Sparking plug tester Neon type 17
09 Gauge wheel alignment universal ( to measure caster chamber, toe-in & toe-out (computerized) ( Mantac )
07
10 Section Engine gear box and differential mounted on chassis 4 cylinder / 4 stroke petrol/ diesel and MPFI type.
10 each.
11. Brake assembly, master cylinder, wheel cylinder and Servo .
14 each.
12 Vacuum assisted hydraulic brake assembly with vacuum booster.
12
13. Compressor air piston type vehicular. 07
14. Air brake assembly foot operated / Disc brake with alternator Maruti type / Gypsy.
14
15. Brake lining riveting Machine (foot operated) 13
16 Clutches different types such as cone type, disc type etc.
9 each.
17. Axle, gear bases, steering boxes, front axle, axle assembly independent front wheel spring assembly
15
18 Full floating axle and semi-floating axle assembly. 11 each.
19. Spring tension scale 0-4.5 kg. 12
20. Value spring compressor. 18
21. Calibrator repair took kit. 10
22. Puller set steering wheel universal. 12
23. Puller set universal bearing and bushes/ Axle puller. 15
24. Lifting jackscrew type 3048 kgs. 16
25. Hot patch clamp. 13
26. Piston ring compressor, 17
27. Valve re-facer. 10
28. Tire changer (clamping range 10-20” Ext. rim Clamping 10-17.5” Internal Rim clamping 12-20” Air supply 6-12 bor
10 each.
29. Connecting rod alignment fixtures. 13
30. Piston ring expander 06
31. Engine Scanner 08
32. F.I. Pump calibration machine with facility of checking in line and rotary F.I. Pump 4 cylinder/ 6 cylinder with pump coupling
2 each.
33. Wheel balancer. 06
34. Grinder with two 7” wheels with twist drill grinding 08
35. Arbor press hand operated ½ tone 07
36 Petrol Engine ( Running condition)car type Indian make ( MPFI/Maruti type 3 cylinder)
16 each.
37 Air compressor 2 stage 500-lit with rest proof tank 5 HP motor and air receiver.
06
38 Car washer reciprocating type electrically operated with 3 HP motor, 3 phase 272 liters tank capacity.
05
39 Spark plug cleaning and testing equipment. 08
40 Hydraulic hoist 4000 kg complete 01
41 Diesel engine cut away model to show working parts for demonstration 2 stroke & 4 stroke.
04 each.
42 Diesel engine 4 stroke multi cylinder 4/6 vehicular type.
14 each.
43 Portable lifting crane one ton capacity with chain block and tackle arrangement
07
44 Trolley type portable air compressor single cylinder with 45 liters capacity Air tank all accessories and with working pressure 6.5 kg/Sq cm.
10
45 Chain Block 3050 Kgs. 03
46 Pressure Grees gun 30 Kg capacity. 07
47 Diesel Engine ( Running Condition) Six cylinder. 19
48 Petrol Engine 2 stroke, motor cycle 15
49 Petrol Engine 2 stroke, Scooter 13
50. Exhaust Gas analyzer (4 gases)with engine rpm sensor and engine coolant temperature sensor. Petrol
09
51. Smoke density meter with engine rpm sensor & engine coolant temperature sensor
07
52. Tyre pressure gauge. 07
53. Two post lift Capacity- 3.2 tons
05
54. Wheel Alignment: Four headed, inflated cable less Lod less,(6x4).video graphic computerized infrared wheel aligner 6 beam alignment concept with video synthesizer
04
55 Wheel balancer: video graphic computerized wheel balanced with 14” color display.
07
56 Tyre regulator Intelligent electronic tyre regulator with dual LED display.
06
57 Fuel Injector Cleaner Universal cleaner for mechanical and electro magnetic regulator for both mono point and multipoint regulator with electronic system for cleaner up to eight indictors simultaneously .
05
58 Pneumatic gun ½” Sq drive impact wrench along with pressure pipe.
07
59 Vacuum cleaner Wet and draw vacuum cleaner with double motor.
10
60. Tech I and Tech II Computer
07 each.
61. Head light tester, Head light tester on rails. 09
62. Tyre changer, Automatic tyre changer suitable for alloy and Large and broad rim size.
09
63. Tool kit complete for Automobile having 72 items trolley type
37
64. Car Washer 04
ANNEXURE ‘D’ OF DETAILED TENDER NOTICE NO: DTE/PUR/2007-08/ DATED: -10-2007 Engineering Drawing / Draftsman Civil / Interior Decoration and Designing equipments/ Measuring Instruments General S.No.
Name of Item. Qty. Rate per
Unit.
Taxes. Total.
01 Drafting Machine-Vertical type complete with drawing board adjustable table and pair of metric scales
a) 30cm b) 40cm
19
02 Drafting Machine-Horizontal type complete with drawing board
adjustable table and pair of metric scales a) 30cm
b) 40cm
19
03 Planimeter sliding bar pattern 70cm complete in case with magnifier
and instructions reading in metric units. 10
04 Pantograph-brass-complete in wooden case with accessories 60cms 10 05. Beam compass with fine adjustments with ink and pencil points and
two chromium plated weights 30 cm in wooden case 06
06 Elliptic trammel with ink and pencil for not less than 10cm minor axis complete in a case
03
07 Clinograph Wooden 18cm 03 08 Leroy Printing Set 19 09 Printing Frame
a) 45cm x 60cm
b) 80cm x60cm
03 each.
10 Tracing Table with plate glass 1250 x 900 cms. 10 11 Weighting triangle with tape 1250x900 cms 06 12 Ammonia box 120cm x 35 x 35cms. 17 13 Table drafting for boards. 40 14 Draftsman Stool height ( 2 ½ ft.) 173 15 Working table blue printing 5’x 10’ 20 16 Interlock, interchangeable brass stencils with brush in a box. 40 17 Printer Trimmer Cutting edge 100cm 03 18 Chest of Drawers 8 drawers ( standard) 40 19 Draftsman Table 19mm top height 2 ½ ‘
a) 4’ x 6’ b) 2’X3’
64 each.
20 Light tracing board fitted with glass and frame and lamps. 03 21 Optical square PWD pattern 12 22 Dumpy level-builder 25cm local length x 23mm complete with box and
accessories and stand 06
23 Plain table with stand
06
24 Alidade. 06 25 Through Compasses 06
ANNEXURE ‘E’ OF DETAILED TENDER NOTICE NO: DTE/PUR/2007-08/
DATED: -10-2007
DIGITAL PHOTORAPHER EQUIPMENT.
.
S.No Name of the equipment Qty. Rate per Unit.
Taxes. Total.
01 Single lens reflex 35 mm camera with normal lens .
High-Resolution 8.2 mega pixels .CMOS Sensor high
resolution images. E-TTL II Imaging Processor Chip,
Direct print support, Fast shutter speed of up to 1/8000
seconds .USB 2.0 high speed Interfaces.
01
02 Single lens reflex 35 mm camera with autofocus lens.
16.7 mega pixel resolution. Full fram 35mm-flim CMOS
sensor
Speed range 100-1600 (1/3 stop,).L:50 H:3200.Shutter
speed of upto 1/8000 sec. Direct print support
01
03 Digital Still Camera flash card type .
8.0 Mega pixels 3.6x optical zoom.9 point AiAF Superior
UA Lens.21 Shooting modes Night display function.
02
04 Digital SLR Camera with Cam Corder .
1/6 800k pixel CCD and DIGIC DV. 22xoptical
zoom/wide attachment. High Resolution 16.9 Mode.
Image Stabilizer. Automatic Easy Mode.2.4 LCD /colour
viewfinder. Super Night Mode .Digital stills with XGA
resolution. SD/MMC Card (1Gb). Direct print /Picture
bridge.
01
05 Digital SLR Camera with detachable recorder.
Video recording system 2 rotary heads digital component
recording. Audio recording system PCM digital sound
Image sensor 3 CCD 1/3 Inch Pixel Shift.(2500000
effective Pixels) Max recording Time SP:60 minutes
LP:90 Minutes .Lances mount XL interchangeable lens
System .Focusing System TTL auto focus, manual
focusing possible .Min Focusing Distance 2 Cm on Max
wide angle .Max shutter speed 1/10000 sec. Fitter
diameter 72mm .Viewfinder 0.7 Inch Colour LCD
01
Microphone Stereo. Detachable recorder
06 Handycam.
5.0 mega pix
Digital zoom
2.5”LCD 5.0 mega pix
32 Mb Internal memory, memory stick pro (512 MB)
Shutter speed min(30sec.)Max.(1/1000 sec.) with inbuilt
flash
02
07 Wide A Wide angle lens matchable with Digital SLR camera
( 24mm, 35 mm)
01 each.
08 Telepho Telephoto lens matchable with digital SLR Camera
( 210mm, 300mm)
01 each
09 Zoom Lens matchable with Digital SLR camera
( 28-70mm, 70-300mm)
01 each.
10. Fish eye lens match able with Digital SLR camera
(17mm)
01
11. Camera stand for still camera.
01
12. Camera stand for Video ( Low base) 01
13. Cable release. 02
14. Different types of filters, (10 types) matchable with
camera
(Graduated, Star filter, multi image, ND, Sky light,
Polarizer, Colour filter set, 80B, both for video & still )
01 each.
15. 15 Extension ring ( 4 types )
02
16. Electronic flash gun with slave unit.
I - Manual
II- Auto
04 each.
17 Studio Light 04
18. Spot light. 02
19. Electronic umbrella light. 04
20. Exposure meter. 02
21. VCR according to digital Camera 01
22. VCR with play back adopter for camcorder 01
23. Digital Pro Lab processing equipment 01
24. Twin lens reflex Camera
01
ANNEXURE ‘F’ OF DETAILED TENDER NOTICE NO: DTE/PUR/2007-08/
DATED: -10-2007
MEDICAL ELECTRONICS EQUIPMENTS.
S.No Name of the equipment Qty. Rate per Unit.
Taxes. Total.
01 Heavy duty hot air oven
I- Powder coated
II- Capacity of 3 shelves or more
06
02 Incubator
I General purpose incubator
II Thermal switch controlled
III Low voltage operable
06
03 Spectrophotometer
General Purpose Spectrophotometer
03
04 Colorimeter
I - Heavy Duty
II- Capable of more than 50 tests Phase
meter.
03
05 PH Meter:-
I. Microprocessor based.
II. Memory of 700 or more samples.
III. Alpha numeric Display
06
06 Flame Photometer (Latest)
03
07 Blood Gas Analyzer.
I- Measured Parameters tHb 5-20 g/dl
II Detection Range 02Hb 0-100%
CoHb 0-100%
Met Hb 0-100%
HHb 0-100%
III. Calculated Parameter sO2
O2Ct O2 CAP
IV Sample Volume 65pl(syringe When>1.5%)
V. Turnaround time 60 Seconds
VI. Wavelengths 6
VII. On-Board Printer Available facility
VII. On-Board Qc Available facility
03
VIII. Standard Interfaces 2xRs232
Cserial:1xParallel 2xBlood Gas
IX. Interfaces capability All IL 1300.1400and
1600 Blood Gas models. IL 131 Ticker Printer;
external Computer
Facility for correcting HbF and Turbidity and
detection of
Sulfhemoglobin when >1.5%
08 Short Wave Diathermy.
I Continuous mode
II. High output of upto 500W
III. Designed with OSC valve operation
IV. Provision of Disc Electrodes
V. Operating frequency of 27.12 mhz
VI. Timer from 0 to 30 minutes
VII. Intensity control in 5 steps with heavy duty
rotary
VIII- Separate meter provision for Filament
voltage output
IX- Pair of pediatric pad with felt and cover
06
09 Microwave Diathermy.
I.- 64 K bit Smart Card, Inches LCD Graphic
display
II- 250 W (In constant mode) and 1600W (In
pulsated mode)
III- Overheating Alarm
IV- Approx. 50 memorized protocols with space for
memorizing 50 protocols
V- With circular antenna, 3 dimensional antenna,
rectangular
antenna
03
10 Ultra Sonic Therapy. 1 & 3 mhz Ultra sound
frequencies
II- both pulsed and continuous modes
III- Variable duty cylce (16hz, 48 hz and 100 hz)
IV- BNR 5:1 Maximum
V- Clinical protocols
VI Sound heat coupling feature
VII- Head warming option on sound head
VIII- Battery power back up system
03
11. E.C.G Recorder.
I- 90 mm chart Paper
II- Copy function.
III- Weight:2Kgsincluding battery
IV- Paper speed:5-25-50mm
V- Auto recording of 12-lead.
VI- 2-line LCD for status display and operation.
VII- Verification of ECG Signal quality
VIII- Anti-drift system ADS
IX- RS-232 interfaces.
06
X- Mains-cum-battery operated.
XI- ICE complied.
XII QRS beep indicating the rate and “heart rate out
of range” Volume adjustable.
XIII- Manual recording of 3 leads.
XIV- Arrhythmia event recording of 3 Leads.
(XV) Interpretation of ECG.
12. Bed Side Monitor
I. Lethal Arrhythmia (II- External sync output
III- Ethernet connectivity (IV- IBP
06
13. Defibrillator.
I- Event and action memory with graphical rep.
II- Screen display 180 degree rotation
III- Auto sequential programming for Joule sequence
IV- Automatic lead switchiry
V- Mains and battery operational
VI Exclusive mains operation without battery
03
14. Pace Maker. (Latest) 06
15. 60 mA Mobile X-ray equipment.
I- Easy Mobile stand with 3 Wheels and Brake.
II- BARC, AERB Approved Machine
III-60 MA at 100KVP with 40 and 20 MA stations.
IV-Timer 0.06 to 10 Seconds. (V) 4.5 K.W Machine
VI- DSA 3 bell tube 40 Khu with 2.8 mar focus.
VII-Cassette carrying assembly in the control with
counter balance for tube and flexible arm.
03
16. Dental X-ray equipment.
I.- 20 MA machine with separate tube and control
with stand
II. Separate KVP at timer.
III. Bell tube only
IV- SCR controlled contacts.
V- Separate meters for Voltage and MA
03
17. Dental Chair.
Electrically Operated with Hydraulic adjustment of
sear and tilting back rest, electrically Swivel Spittoon
and tumble filler and inbuilt pneumatic and vibratory
suction with collection bottle, air rotator control with a
3 way syringe one point for air rotator and second
point for air motor and third point for micro motor.
Pneumatic Stool and oil free 1 HP compressor with
Italian head consisting of auto start and stop facility
accessories with assent arm having total attached
mobility permitting four hand pieces. The hand kit
compressing of four hand pieces should be supplied
with the chair.
03
18. Portable Ultra Sonic Scanner. I- Foldable keyboard ( II ) TGC (III) 16 or more
channel beam former fully digital. (IV ) Less than
03
10 kg in weight.
(V )BB, BM, M. (VI ) ATO (VII ) PIP zoom
without losing sight of original image. (VIII ) 32 or
more cine memory
IX- 16 or more image memory up gradable to 172 or more
X- 3.4 mhz 50mm radius 68 degree field of view
probe
XI- 7.5, 5.0, 6.5 adaptable. (XII ) Probe
19. Surgical Diathermy.
I.) Micro controlled Technology. (II) Auto stop
coagulation function. (III ) Programming of 9 or more
surgeries
IV) PPCM Technology. (V) Separate Isolated Output
for Mono and Bi Polar. ( VI) Up-gradable.
03
20. Pulse Oximeter.
I- True trace and profusion track technology 30hrs
backup
II- Efficient perfusion index
III- No motion artifacts (IV) Handy
03
21. Theatre Lighting system.
I- Dome Diameter 525 mm
II- Halogen Lamps
III- Lamp Life 500 hrs or more
IV- Light output 50000 Lux
V- Spring counter bells
VI- Colour correction filters
VII- Low power composition
VIII-Light weight
06
22. Baby Incubator (Digitally control)
03
23 Ventilators.
I- Ability to integrated ventilation gas monitoring
II- Integrated nebaliser
III- No invasive ventilation
IV- Maintenance free paramagnetic oxygen sensor
03
24 Simple Sterilization equipment.
12
25 U-V / IR lamps.
I- Ultra violet lamp with stand Indian
II- It must be with height and angle adj mobile stand.
12 each.
26 Muscle Stimulator
I- 2 independent Electrotherapy channels
II- more than 200 Clinical protocols
III- EMG and sEMG + Electrical Stimulation
IV- Facility to record the data of 300 patients
V- sequencing to direct a designated therapeutic
VI- Facilicy for function electric stimulation
06
27 Fetal Monitor
I ) 9 crystal transducer (II) Big LCD display
03
III) Telemery interface (IV) Foetal movement
detection
28 Conductivity Meter
I) Auto ranging. (II) 20 Micro siement to 200
millisiement in five ranges.(III) Programmable
temperature Co-efficient adjustment.(IV)Date Storage
of 700 reading.
(V) Micro process based.
06
29 Stand Type Mercury Based B.P. Apparatus (
Sphygmo Manometer
03
30 Stethoscope (Latest).
12
31 Wax Bath.
I) Mains Voltage :110-120 or 220-240 Voltage 50-
60 Hz
II) Power consumption;2000 Watts
III) Tank capacity :30 Liters
IV) Heat Transfer Liquid :10 Liters water
V) Temperature Range :30 9-Deg c
VI) Dimension 9 (outside ):56x36x45 Cm
06
32. Suction Apparatus.(Latest)
03
33. Microscope. (Medical Binocular).
03
34. Blood Cell counter
03
ANNEXURE ‘G’ OF DETAILED TENDER NOTICE NO: DTE/PUR/2007-08/
DATED: -10-2007
List of Machinery / Equipment Mechanic Industrial Electronics. S.No. Name of the items with specification. Qty. Rate per
Unit. Taxes. Total.
01 Automatic Sequencing Control 05
02 Counters 12
03. Temp Controllers 12
04 EPROM Programmer 03
05 Microprocessor Trainer Kit along with ADC /DAC with
stepper motor controller and Eprom Programmer
05
06 Proximity Switches 12
05 Photo Techno meter 10
08 Burglar Alarm 06
09 Spindle controller 01
10 Rotary Encoder 05
11 Computerized Numerical Scale (CNS) 05
12 Programmable Logic Controller (PLC) 07
13 High Voltage testing kit 01
14 Surge Generator 01
15 Instrument Tutor 01
16 Electronic Voltmeter – 0-500v 05
17 S.M.P.S Trainer 02
18 Analog Semi Conductor Trainer including power Semi
conductor devices
05
19 Digital Trainer A/D, D/A converter , mux, demux-display
devices etc
03
20 EEPROM Programmer-cum copier with UV Eraser 03 set
21 Motor Trainer with dummy loads 02 each.
22 03 phase motor speed controller / trainer 02
23 Hot Air Soldering cum de-soldering station for SMD
devices
09
24 PLC Trainer 03
25 CNC Trainer- 03
26 Servo controller. 01
ANNEXURE ‘H’ OF DETAILED TENDER NOTICE NO: DTE/PUR/2007-08/
DATED: -10-2007
MACHINERY EQUIOPMENT FOR MACHINIST TRADE.
S.No. Name of the items with specification. Qty. Rate per Unit.
Taxes. Total.
01 Shaping Machine 450 mm stroke ( Motorized) with all
attachments like gear cutting attachment with dividing head,
swivel based machine vice 300mm
02
02 Shaping machine 315 mm stroke (Hydraulic) with all
attachments. 01
03. Double column planner 1500x 1000x 1000 mm
(motorized)with all attachments 01
04 Slotter 180 mm stroke (motorized)with all attachments
rotating table with universal cheek with cross and transverse
feed arrangement
01
05 Cylindrical grinder with all attachments, accessories and
sorts and sizes of external and internal grinding wheels with
all automatic driven attachments
11
ANNEXURE ‘I’ OF DETAILED TENDER NOTICE NO: DTE/PUR/2007-08/
DATED: -10-2007
WELDER TRADE. MACHINERY / EQUIPMENT.
S.No. Name of the items with specification. Qty. Rate per
Unit.
Taxes. Total.
01 Welding Transformer 200-300amp continues welding current with all accessories (220/440v)
01
02 Arc Welding rectifier set 200-230 amp continuous welding current with all accessories three phase
01
03 Welding motor generator set AC/DC 200-300amp 3 phase/single phase with all accessories
01
04 Oxygen Cutting Machine
01
05 Acetylene Generator ( Carbide to water)type. 02
06. Acetylene Generator ( Water to Carbide) type. 02
07. Gas Welding table 82x92x60 cms (metallic)with fire bricks on stand.
05
08. Arc Welding table all metal with positioner 122x 92x 60 cms.
11
09 Trolley for high pressure unit * to carry cylinders) 01
10 Bench shear hand capacity up to 12 mm 02
11 D/E grinder 30cms wheel motorized (Pedestal type) Would make.
03
12 Horizontal circular hand saw ( Similar to Garlic ) 01
13. Electro dying over thermostatically controlled temp. 0-250 degree 10 kg capacity.
02
14 Braze weld equipment 02
15 CO2 Welding machine complete 400 Amps 02
16 Tig Welding set complete 300 Amps 04
17 Power Hacksaw complete 01
18 Pipe bending Machine capacity upto 2” bending 03
19 Flexible shaft Grinder 10cms wheel dia 01
20 Trans pocket 1500, 1500RC, 1500 Tig Rod Electrode + TIG DC Welding.
02
21. Roto Fuse, Fusible Powered Metal Alloys. 02
22 Termomatec Eut - O- Matec Wire Feeder. 02
23 Flash Back Arrestor ( Safety to Welder Trade) 01
ANNEXURE ‘J’ OF DETAILED TENDER NOTICE NO: DTE/PUR/2007-08/
DATED: -10-2007
REFRIGERATION AND AIRCONDITIONING MECHANIC TRADE MACHINERY EQUIPMENT.
S.No. Name of the items with specification. Qty. Rate per
Unit.
Taxes. Total.
01. Pressure Gauge diameter 63 mm with Recalibration set screw, scale 0 to 35 Kg/ sq.cm
24
02 Compound gauge, diameter 63 mm with Recalibration set
screw, Scale Vacuum 76 mm, pressure 15 Kg/ Sq cm.
24
03 Service thermometer in metal case -30 to + 30°C 24
04 Sling psychomotor mounted on Aluminum back, Scale -
50°to +50°C portable in Leather Case.
12
05 Gas Leak detector for Halogen Gas. 12
06 Lapping Plate 250 x 250 mm. 12
07 Gas cylinder Trolley two Wheel type 06
08 Variac Input 230 Volt Out put 400 volt 30 Amp. portable complete with meters and controls.
07
09 Refrigerant Charging Station consisting of:
a)Rotary Vacuum Pump with machoid gauge, two stage, self contained with motor, portable, final vac.0.1/Splash
reducing, non-return valve, Cap-1/2 HP valve, 0-1 micron with gas ballistic.
b) Graduated cylinder, stainless steel, portable cc & mm
scale, compensation for Vol. Fluctuation with pre-release valve, gauge etc.
c) Charging manifold with valves & gauges.
06
10. Dial thermometer, remote control, armored capillary dial 75mm -50°C to 50°C.
12
11. Rotary Vacuum Pump with 0.5 HP Motor, non-return valve & gas ballistic valve.
06
12. Anemometer. 07
13. Descaling pump set with stainless steel impeller and housing
complete with motor 1 HP and accessories.
06
14. Spray outfit, ‘V’ twin, with motor ½ HP delivery upto 120
liter free air pressure upto 3 kg/sq. cm. With spray gun and
fitting.
07
15. Pressure testing tank with lighting arrangement pressure
gauge (0 to 35 kg/sq.cm) double stage regulator, Pressure relief valve and nitrogen cylinder.
07
16. Heating kit with infra red bulb (200 watt. Capacity) 07
17. Refrigerator compression type 165 liter . 07
18. Refrigerator, compression type 300 liters double door, double compressor system.
06
19. Deep Freezer 165 liter,- 18°C, ¼ HP 13
20. Bottle cooler, 110 liters, 1/6 HP 06
21. Water Cooler instantaneous type. 06
22. Water Cooler, storage type. 06
23. Ice candy unit complete with stainless steel tank, mould
box, thermo cool insulated sun mica body, Agitator, compressor, motor etc. temp. pressure, refrigerant control
gauges, motor, pipe fitting etc. 3000 k.col/hr. or working trainer model/ Simulator.
06
24. Cold storage plant complete with all controls and accessories
including cooling tower and water treatment plant capacity 15000k. cal/hr. or working trainer model/ emulator.
06
25. Air Conditioning Plant, direct and indirect water chiller,
complete with all controls including humidity control etc. capacity 15000 k.cal/hr. or working trainer model/ Simulator
07
26. Condensing unit, with open type compressor air cooled
condenser controls etc. capacity 750 k.cal/hr.
06
27. Condensing unit with open type compressor evaporative
condenser controls, etc. Capacity 3000 k.cal/hr.
06
28. Reciprocating compressor with provision of capacity control etc. for demonstration, capacity 9000 cal/hr.
06
09 Refrigeration and Air Conditioning Tutor 03
30. Refrigerant cylinder capacity 2.5 Kg. 12
31. Refrigerant cylinder capacity 30 Kg. 12
32. Oxy-Acetylene Welding set complete with Cylinders,
regulators welding torches with different nozzles.
06
33 Air comporssor tow storage oil less dry air with rust proof tank assembly heater & controls MAX. PR. 10 KG/CM2.
Capcity 45 ltr. Motor 1 hp.
06
ANNEXURE ‘K’ OF DETAILED TENDER NOTICE NO: DTE/PUR/2007-08/
DATED: -10-2007
MACHINERY EQUIPMENT OF FASHION TECHNOLOGY / DRESS MAKING and CUTTING SEWING TRADES. S.No. Name of the items with specification. Qty. Rate per
Unit.
Taxes. Total.
01 Lock Stitch (Multipurpose fashion design maker machine motorized complete with stand heavy sun mica top
23
02. Over Locking Machine with stands & heavy sun mica top Twin needle (Motorized) 3 threads
13
03. Over Locking Machine with stands & heavy sun mica top Twin needle (Motorized) 5 threads
12
04. Bar-tack Machine Motorized
14
05. Button Hole Machine Motorized
15
06 Dummies a. Dummies Gents 40 Full 27 b. Dummies Gents 42 Full 27 c. Dummies Ladies 8 Half 27 d. Dummies Ladies 10 Half 27 e. Dummies Ladies 12 Full 27 f. Dummies Children 4 Full 27 07 Commercial type swing machine with threadle &
mounted suitable on a table having a drawls. 81
ANNEXURE ‘L’ OF DETAILED TENDER NOTICE NO: DTE/PUR/2007-08/
DATED: -10-2007
MACHINERY EQUIPMENT FOR TRACTOR MECHANIC TRADE. S.No. Name of the items with specification. Qty. Rate per
Unit. Taxes. Total.
01 Marking Table 90x 60x 90 cm
02
02 Tool Valve grinding suction type
07
03 Tool Valve grinding screw in type
02
04 Valve seat cutting, tools complete with guides and pilot
02
05 Bar ( All angles) Drop fogged
01
06 Valve grinding Machine
01
07 Compression gauge to read 0-115 kg/cm
02
08 Vacuum gauge 0.75 cm
03
09 Injector testing set ( Hand tester)
04
10. Cylinder gauge capacity 6-15cm
03
11 Fuel Pump
03
12. Injection Pump
02
13 Injector ( Two Types)
05 each
14 Water Pump and Oil pump
03 each.
15 Filing jig for adjusting the piston ring gap
02
16 Brake drum spring balance belt etc for performance testing of engine.
02 set.
17 Spray gun set with accessories.
04 set.
18 Grinder with two 18cm wheels with twist drill grinding attachment
03
19 Compressor capacity 12 C.F.T piston type with pressure gauge
03
20 Hydraulic Jack Hi-lift type. Crawler type tractor fitted with diesel engine with accessories and special tools ( 50-60 dra-bar H.)
04 each.
21 Wheel type tractor fitted with diesel engine with diesel engine with standard accessories and special tools ( 30-40 draw-bar H.P)
04
22 Trailing type three bottom mould board 30cm size with coulter and jointer
01
33 9 tine cultivator-spring loaded
01
24 3 Furrow disc plough with scrapers. 01
25 Ridger
01
26 Rear axle assembled gear box, steering box of the diesel Engine Tractor
02 set each.
ANNEXURE ‘M’ OF DETAILED TENDER NOTICE NO: DTE/PUR/2007-08/
DATED: -10-2007
MACHINEY EQUIPMENT FOR TURNER TRADE. S.No. Name of the items with specification. Qty. Rate per
Unit. Taxes. Total.
01 Lathe S.S. & S.C ( all geared head stock) 15cm ht to admit 120 between centres. Motorized supplied with coolant installation with four jaw 250 mm and three jaw 150mm chuck fixed steady & travelling steady, fact plate, driving plate and with quick change gear box metric & British and live dead centres with taper attachment
11
02. Lathe S.S. & S.C all geared 20cm height 120 cm between centres, gap bed m/c Motorized & supplied with coolant installation, 4 jaw chuck 300mm and jaw chuck 300 mm, fixed steady, face plate, driving plate, quick, change gear box for metric / British threads line and bed centres with taper attachment.
08
03. Lathe tool room S.S & S.C all geared 15cm height 120 cm between centres. Motorized and supplied with coolant, 4 jaw chuck 250 mm, 3 jaw chuck 150 mm, fixed and travelling stadies, face plate, driving plate, draw in collets set up to 25mm, 0.5mm relieving attachments
05
04. Lathe S.S. & S.C (Cone Pulley type) 15cm Height, 90cm between centers. Motorize and with four jaw chuck 250mm, 3 jaw chuck 150mm, single tool post
02
05. Grinding m/c pedestal type D/E 250mm dia and 150mm dig wheel with wheel and vision guard, 3 phase 415 v 1 HP motor
02
06. Power Hack saw with hydraulic feed system 400mm blade size
01
07 Capstan lathe 250mm sawing 25mm spindle bore with all accessories and attachments collet, chucks and sets etc.
01
08. C.N.C Lathe machine 6 ft long 02
09 C.N.C Turning and Grooving tools assisted
02 set.
10 Wheel Dresser hunting on type with star cutter. 02
11 Micrometer screw thread interchangeable anvil for various metric pitches.
01
12. Sine bar with centres 200 mm 01
13. Morse taper sleeve No:- 0-1, 1-2,2-3, 3-4,4-5, 1-3 with drift
02set
14 Drill chuck with key cap up to 12mm ( JUG) 02
15 Tool holder RH & St. for 6 mm square tool bit 10-20 mm
12
16. Parting tool holder with H.S.s blade 18
17. Boring tool holder for 6mm bits. 12
18 Dog carriers 25, 50, 75, 100, 125, 150mm 01
19. Angle plate with slots 200mm 01
20 Tool maker button 01 set
21. Combination drill A-25 & A-1 12
22. Angle gauge for tool grinding /drills
07
23 Hand chaser Ext & Int M-12 & M-16
02 each.
24. Machine chaser “Std” to suit on conventry dia head M12, M21 ( Totum )
01 set
25. Magnetic chuck “ Circular” type 150mm 01
26. Lathe Mandrels different types Carbon E.N9 graded steel.
01 set
27. Coventry type Die-head “ Self opening” 01
28. Collapsible tap with attachment 01 set
29. Combination drill 01
30 Machine vice for drill machine 100mm jaw 01
ANNEXURE ‘N’ OF DETAILED TENDER NOTICE NO: DTE/PUR/2007-08/
DATED: -10-2007
MACHINERY / EQUIPMENT FOR ELECTRICIAN TRADE ETC.
S.No. Name of the items with specification. Qty. Rate per
Unit.
Taxes. Total.
01. Battery Charger, 24V 50A. 18 02. Variable auto transformer 0-300 V, 10 A. 27 03. Electrical Machine Trainer:-
Suitable for demonstrating the construction and functioning of
different types of DC machines and AC machines (single phase
and three phase) with friction brake dynamo meter, instrument
panel and power supply units.
06
04. WORKING MODELS:-
Demonstrating type working models of all AC/DC, Motors /
Generators / Transformers three phase and single phase.
21 each
05. DIESEL GENERATOR SET:-
3 phase four wire 440/220V ,5 KVA. Engine 10 HP, 2
Cylinder, water cooled with change over switch. Overload
circuit breaker, Starting, hand / battery.
11 each.
06. Synchronous Motor, 1 phase, 1 HP, 1500 RPM with complete
control panel and DC excitation. 13
07. Synchronous Motor, 3 phase, 5 HP, 1500 RPM with complete
control panel and DC excitation. 10
08. Stepper motor, single phase. 14 09. Motor AC, 3-phase, squirrel cage, 440 volt, 50 HZ, 2 HP. 12 10. Motor AC, 3-phase, double cage, 440 volt, 50 HZ, 2 HP. 08 11. Motor AC, 3-phase, deep bar cage, 440 volt, 50 HZ, 2 HP 08 12. Slipring motor, 5 HP, 440 V, with starter and control panel. 09 13. DC Series Motor, 220 V, 2 HP. with complete control panel. 03 14. DC Shunt Motor, 220 V, 2 HP. with complete control panel. 04 15. DC Compound Motor, 220 V, 2 HP. with complete control
panel.
05
16. Fractional Horse Power Motor, DC, 220 V 07 17. Single phase alternator, 250 V,1 KVA 10 18. Motor Generator set consisting of :-
Squirrel Cage Induction Motor, 7 HP, 3 phase, 440 V, 50 HZ,
with automatic star / delta starter and main control switch,
coupled to DC Shunt Generator, 5 KW, 440 V, and switch
board with regulator, air circuit breaker, knife blade switch,
fuses, ammeters, voltmeters, frequency meters on both AC &
DC sides.
06
19. Motor generator set consisting of :
DC Shunt Motor 5 KW, 220 Volts with switch and starter (three
point) directly coupled to AC Generator 3.5 KVA, 400/230
volts, 3-phase, 4 wire, 0.8 PF 50 cycles with exciter and switch
board mounted with regulators, circuit breakers, ammeters,
voltmeters, double reed frequency meters, Synchronous cope,
knife blade switch and fuses etc.
04
20. Rotary Converter with input AC single phase 250 Volts and
output DC 220 Volts,
20 Ampere.
15
21. Rotary Converter with input AC three phase 440 Volts and
output DC 220 Volts,
50 Ampere.
08
22. Current transformer portable, primary
1200,600,400,300,200,150,100,75,50,30,20,10 A
Secondary 5 A
10 each.
23. Potential transformer 11 KV / 110 V. 10 24. Transformer single phase, 3 KVA, core type, air cooled,
primary 230 V, secondary having tapings of
80,100,130,150,180,200,230 V. (
13
25. Transformer three phase, 5 KVA 400/230 V, air cooled. 08 26. Electronic Typewriter 14” paper capacity 14/18 Cps print
speed, 48 K memory, 5 line graphic display(with extra two
daisy wheels)
‘
15
27. Portable Typewriter 14 28. Dating Machine ( Small Size) 07
ANNEXURE ‘0 OF DETAILED TENDER NOTICE NO: DTE/PUR/2007-08/
DATED: -10-2007 Machinery General.
S.No.
Name of the items with specification. Qty.
Rate per Unit.
Taxes.
Total.
01.
Drill Machine Chuck Model with bench drill stand 20mm ,220v.
04
02.
Drilling Machine Piller type 0-20mm capacity with swivel table motorized with chuck and key.
11
03.
Bench Grinder 220V 01
04.
Bench Grinder 440V (three phase) 27
05.
Flexiable shaft Grinder 235V 125mm 01
06
Grinding Machine General Purpose D.E pedestal with 20 cms dia wheels rough and smooth with twist drill grinding attachment.
27
07.
Water heater 25 liters 250V/2000W(Geyser) 03
08
A Simple R,0, sealing machine for bottles and jars 02
09
Can sealing machine manually-operated similar to Dixie sealer or the power driven, more costly MB No: 1A Seamer
02
10
Crown corking machine, manually operated. 02
11
Carbonation Unit. 02set
12
Vinegar Generator Set 02 set.
ANNEXURE ‘P’ OF DETAILED TENDER NOTICE NO: DTE/PUR/2007-08/
DATED: -10-2007 Dental Laboratory Technician Trade Equipment.
S.No. Name of the items with specification. Qty. Rate per
Unit. Taxes. Total.
01 For Denture Section and Metal Section:-
Banging Motor 06
Hand Piece 06
Cable Arm 06
Micro Motor Inc. Hand Piece 02 set.
Vacuum Mixer Cum Vibrator Mc. 02
02. For Wax-up Section.
Electro Waxer M/C with hand Piece 02 set.
Hand Was curver (Pkt set) 02 set.
03 For Ceramic Section.
Multimate Furnace 04
Vita Vacumat-40 Furnace 02
Micro Motor with Hand piece 04
Compact Ultra Sonic cleaner 02
Vita Chrom Delta Stains 02box
VKM 95 (3-D masters std.Set-12) 02box
Ultrasonic cleaner 02
04 For Casting Section.
Induction Casting Mc.(Galloni) 02
Sand Blasting Mc. 02
Heating Furnace. 02
Muffle Furnace. 02
Manual Casting Machine 02
Air Compressor. 02
05 For Model Section.
Trimmer 02
Finishing lathe 02
Heating oven. 02