GPS PLOTTER

GP-1850/W Series

The paper used in this manual

is elemental chlorine free.

・FURUNO Authorized Distributor/Dealer

9-52 Ashihara-cho,

Nishinomiya, 662-8580, JAPAN

Telephone : +81-(0)798-65-2111

Fax : +81-(0)798-65-4200

A : DEC 2002.Printed in JapanAll rights reserved.

A2 : AUG . 22, 2008

Pub. No. SME-43950-A2

*00080992600**00080992600*(KAOK ) GP-1850/1850W SER.*00080992600**00080992600*

* 0 0 0 8 0 9 9 2 6 0 0 *

i

Table of Contents

1. General …………………………………………………………. 1 2. Difference between GP-1850 and GP-1850W …..…………. 1 3. Difference between D, F and DF ……………………….……. 2 4. Replacing major parts …………………………………………. 2 5. How to install DGPS beacon receiver………..…………….… 4 6. Replacing lithium battery ……………………………………… 4 7. How to change software to C-MAP version ………..……..… 5 8. How to upgrade system program …….…………….……..…… 7 9. Troubleshooting …………………………………………………… 8

9.1 Self test ……………………………………………………. 8 9.2 Troubleshoot guide ………………..……………………….. 9

Exploded View…………………………….………………………… D-1

Electrical Parts List ………………………………………………… E-1

Schematic Diagrams ……………………………………………… S-1

This page is intentionally left blank.

1

Range setting: 1200 m

Oscilloscope setting:

5 V/div, 200 us/div

Test points: Pins 8 and 10 on J2

(with XDR connected)0.2 ms

50 kHz: 20 to 25 Vpp

200 kHz: 27 to 32 Vpp

(600 W)

1. General The GP-1850/W series display unit consists of the following components.

Parts Name Function MAIN board The board, heart of the unit consits of a CPU, ROM, RAM,

Card Interface circuit, a buzzer and a lithium battery. The board generates high voltage for LCD backlighting. The difference between A, B, E, and F is system program only.

ANLG board The board includes power supply and echosounder circuits. PNL board The board consists of key switches and backlight LEDs. GPS receiver

The receiver receives and processes satellite signal for position fix.

BEACON receiver

The receiver receives radiobeacon DGPS to remove errors in GPS position fix.

LCD unit High voltage for LCD backlighting is derived from J101 on MAIN board to Cold Cathode Fluorescent Light (CCFL) in the LCD unit.

TX Output signal of echosounder circuit

50 kHz and 200 kHz transmitters in echosounder circuit on 14P0313B board outputs the

following signal to the transducer.

Fig.1 TX waveform of echosounder

2. Difference between GP-1850 and GP-1850W MAIN boards, 14P0311X and 14P0311XW are the same in hardware, but not in software.

Component GP-1850 GP-1850W

MAIN board 14P0311X (Not supporting WAAS)

14P0311XW (Supporting WAAS)

GPS receiver GN7707 (original) GN7801 (compatible with GN7707)

GN8091 (Supporting WAAS)

LCD unit EDTCA-03QCF EDTCA-03QCF-AR LCD protective panel Acrylic plate AR acrylic plate ANLG board 14P0313 PNL board 14P0312 BEACON receiver GR-8020 (original), GR-7000A (Jan. 2000 and after)

2

3. Difference between D, F and DF The letter D in the model indicates that the beacon receiver for differencial correction of

GPS receiver is buit in the unit. The letter F indicates that the unit features echosounder

capability. 14P0311C(W) and D(W) a re for Japanese version.

GP-1850(W) GP-1850D(W) GP-1850F(W) GP-1850DF(W) MAIN board 14P0311A(W)

14P0311E(W) 14P0311A(W) 14P0311E(W)

14P0311B(W) 14P0311F(W)

14P0311B(W) 14P0311F(W)

ANLG board 14P0313A 14P0313A 14P0313B 14P0313B BEACON receiver

Not buit-in Built-in Not buit-in Built-in

Key top (right to PLOT key)

XTE HIWAY XTE HIWAY SNDR SNDR

4. Replacing major parts To replce the major parts, follow the steps below.

1. Place the unit on soft surface – face down. Remove all nuts (arrowed in Fig.2) and 12

screws (ringed) fixing the cover to the front panel. Then, lift the cover. Fig.3 shows

GP-1850/W series display unit with the cover removed.

Fig. 2 GP-1850/W series display unit, rear view

ANLG board

(14P0313A/B)

Connectors: ANT, XDR*, DGPS, NMEA and PWR, from left

*: only F version

Fig.3 GP-1850/W series display unit with cover removed

Do not lose connector gaskets!

3

J2

J6 (Release locking tab by pushingit toward cable.)

MAIN board, 14P0311 Lithium battery at soldering side

J4 (Release locking tab by pushing it toward cable.)

Fig.4 GP-1850/W series display unit with cover removed, top view

2. Remove the screw fixing the GND wire to MAIN board. Then, pull ANLG board

assembly straight upward.

3. Remove the shield cover, and unplug J2, J4 and J6 on MAIN board.

The MAIN board is battery backupped, so it is recommended that before removing MAIN

board, disconnect either lead of JP6 not to damage the components on the board by a

short circuit. With JP6 disconnected, the board is not battery backupped.

Fig.5 MAIN board, 14P0311

Now the LCD unit can also be removed together with the mounting plate.

JP6

LCD unit mounting plate with LCD unit on the back

GND wire

4

5. How to install DGPS beacon receiver Refer to the installation manual.

6. Replacing lithium battery To replace the battery with new one, follow the steps below.

1. Disconnect JP6 on MAIN board. See Fig.5.

2. Use a desoldering tool to remove the battery from MAIN board.

3. Solder the replacement battery onto the board.

4. Solder JP6.

CAUTION

1) Replace the battery only with CR2450-F2 ST2L (000-144-941).

2) Never short + and – sides of the cell.

3) The lithium cell may explode resulting in a fire or chemical burn if

mistreated. Do not recharge, disassemble heat, or incinerate.

4) Follow local ordinances or regulations for the disposal.

Fig.6 MAIN board, soldering side

Lithium Battery

Type: CR2450-F2ST2L

C/N: 000-144-941

5

PC

PLOTTER

DGPS (MJ-7P) >1> >2> >3> >5> >4> >6> >7> >8> >9>

RxD TxD GND DTR DSR RTS CTS

<1< <2< <3< <5< <4< <6< <7<

NC NC RD SD NC S G SHIELD

(DSUB 9P) COM 1

7. How to change software to C-MAP version GP-1640 sereis uses following programs.

Navionics version C-MAP version GP-1850/D : 14518260XX 14518400XX GP-1850F/DF: 14518270XX 14518410XX GP-1850W/WD: 14518260XX 14518400XX GP-1850WF/WDF 14518270XX 14518410XX

1) By using PC The following explains how to upgrade the software by using a PC. The “up boot” upgradation is carried out only when requested. Before upgradation The batch file “up_boot. bat” is designed for the use of COM2 port of the PC. When COM 1 port is used, the batch file needs to be modified by using a text editor application such as Note Pad. The last number is changed from “2” to “1” when COM 1 port is used. Uppg load. bin GPXXXX. 0 0 1 0 0 0 2 Procedure 1. Copy all files in EXE files to PC.

2. Connect the COM port of the PC to the DGPS port of the plotter.

Fig. 7(a) Connection with PC (9 pin Dsub)

6

Fig. 7(b) Connection with PC (25 pin Dsub)

3. Run “up_boot. bat” on PC. The message “TAEGET POWER ON” appears on the

display.

5. Turn on the plotter. You hear three beeps (pi pi pi) and the message “Execute STEP1” appears.

6. Then a beep sounds and the message “Execute STEP2” appears. It takes about 5 minutes to complete steps 4 and 5.

7. When the message “Finish version up” appears, the upgradation of the boot software is completed.

8. Turn off the plotter.

If the up-boot procedure fails, the plotter must be reset by downloading the software from a master program card.

8. Run CTOOL_E.EXE on PC. The CTOOL_E.EXE creates following files.

Models File name GP-1850/1850D GP-1850W/1850WD

1850e. BAT, CU1850e. BAT, LOAD. BIN, UPPG EXE

GP-1850F/1850DF GP-1850WF/1850WDF

1640fe. BAT, CU1850fe. BAT, LOAD. BIN, UPPG EXE

9. Run either batch file, C1850 BAT or C185e.BAT according to the model to get the

binary file (Cxxxe.BIN).

10. Then, run either batch file, CU1850e. BAT or CU1850fe.BAT according to the model.

11. Turn on the plotter when the message “TARGET POWER ON” appears on the PC.

PC

PLOTTER

>1> >2> >3> >4> >5> > 7> >6> >20>

TxD RxD DTR DSR GND RTS

<1< <2< <3< <5< <4< <6< <7<

NC NC RD SD NC SG SHIELD

(DSUB 25P) COM 1 DGPS (MJ-7P

7

2) By using program master card The following describes how to update the software by using the master card. 1. Insert Program master card into the slot.

2. Turn on the power. “NOW LOADING” message appears.

3. When loading is completed, the message “PLEASE REMOVE A CARD AFTER POWER SUPPLY CUTS” appears on the display. Then, the power is automatically turned off. If the power is turned off without the message, the program loading is failed. Repeat above steps.

8. How to upgrade system program The software is updated by following the procedure below.

1) By using PC

Take steps 8 to 11 in the previous section. The Navionics version program files do not

include a letter C.

2) By using program master card

The procedure is the same as the previous section.

8

Caution - High Voltage!

In GP-1850F/DF/WF/WDF, high voltage presents at leads of R116.

Fig.8 R116 on ANLG board, 14P0313B

R116

9. Troubleshooting

9.1 Self test

Self test is performed by following the steps bellow.

1. Press [MENU] key to open the main menu.

2. Press CONFIGURATION soft key to show the configuration menu.

3. Press the SYTEM MENU soft key to open the system menu.

4. Press SELF TEST soft key to open test menu.

5. Press MEMORY I/O TEST soft key to start the test.

The following describes the test result display.

PROGRAM: S ystem program sum check is performed.

SRAM: Read/write test for SRAM on MAIN board is performed.

DRAM: Read/write test for DRAM on MAIN board is performed.

PORT 1: Loopback test is performed for NMEA port interface circuit by

connecting pin 1 to pin 3 and pin 2 to pin 4. This line reads - -

without jumpers on NMEA port.

PORT 2: Loopback test is performed for DGPS port interface circuit by

connecting pin 5 to pin 3. This line reads - - without a jumper on

DGPS port.

INTERNAL BATTERY: NG is displayed when voltage of lithium battery on

MAIN board lowers to 2.5 V.

GPS RECEIVER: GPS receiver is tested. Program nubmer for GPS receiver

is 48502370XX.

9

9.2 Troubleshoot guide Table below provides a problem symptom, followed by a possible solution.

Symptom Possible solution Failure to power Check 5A in-line power cable fuse and

F1(7A) on ANLG board. No buzzer sound Replace MAIN board. Problems on indication Replace MAIN board. LCD not backlighted Replace MAIN board and/or LCD unit.

Voltage at J2 on MAIN board is about 2400 Vpp (850 Vrms) AC.

No sounder picture Replace MAIN and/or ANLG board.

Fig. 10 Jumper blcok, JP1 on ANLG board

Fig.9 ANLG board, 14P0313A/B

Fuse, 7 A, 125V

R104 adjusts switching frequency of 83 kHz.

R88 adjusts 5 V line.

JP1 for output power selection

#1 - #2: 600 W #3 - #4: 1 kW

Antenna connector

This page is intentionally left blank.

APPROVED

CHECKED

DRAWN

DWG. NO.

TITLE承　認

審　査

製　図

2002.9.3

2002.9.3

2002.9.3

GP-1850DGP-1850F/DF

C4395-E01-C

指示器 DISPLAY UNIT

GPS受信機GPS RECIVERGN-7077 orGN-7801A

ﾉﾌ゙KNOB20-007-2302(100-173-273)

WARNING

ﾊﾝｶ゙ 組ー品BRACKET ASSY.GP-1850/D/F/DF(000-790-434)

A

ﾋ゙ ｺーﾝ受信機BEACON RECEIVERGR-8020 orGR-7000A(GP-1850D/DF only)

B

ANLG BOARD14P0313A(1850/D)14P0313B(1850F/DF)

ﾗﾊ゙ ｷーー(E2)/(E2F)(J2)(J2F)RUBBER KEY (E2)/(E2F)(J2)(J2F)14-063-1003(100-270-610)-1850F/DF-E14-063-1004(100-270-620)-1850F/DF-E14-063-1043(100-270-773)-1850/D-J14-063-1044(100-270-783)-1850F/DF-J

PNL BOARD14P0312

ﾗﾊ゙ ｷーー J1/E1RUBBER KEY J1/E114-063-1002(E)(100-270-600)14-063-1042(J)(100-270-764)

MAIN BOARD14P0311A(1850/D NAVIONICS-E)14P0311B(1850F/DF NAVIONICS-E)14P0311C(1850/D NAVIONICS-J)14P0311D(1850F/DF NAVIONICS-J)14P0311E(1850/D C-MAP-E)14P0311F(1850F/DF C-MAP-E)

LCDEDTCA-03QCF(000-140-673)

B

パネル部組品PANEL ASSY.GP-1850/D(J)(000-146-459)GP-1850/D(E)(000-146-460)GP-1850F/DF(J)(000-146-461)GP-1850F/DF(E)(000-146-462)

ﾊーﾄ゙ｶﾊ゙ 組ー品HARD COVER ASSY.GP-1850/F(000-790-436)

Aパネル部組品FRONT BEZEL WITH FILTERGP-1850/D/F/DF(000-146-463)

APPROVED

CHECKED

DRAWN

DWG. NO.

TITLE承　認

審　査

製　図

2002.11.8

2002.11.8

2002.11.8

GP-1850W/WDGP-1850WF/WDF

C4425-E01-A

指示器 DISPLAY UNIT

GPS受信機GPS RECEIVERGN-8091C(000-145-613)

ﾉﾌ゙KNOB20-007-2302(100-173-273)

WARNING

ﾊﾝｶ゙ 組ー品BRACKET ASSY.GP-1850W/WD/WF/WDF(000-790-434)

A

ﾋ゙ ｺーﾝ受信機 (WD/WDF)BEACON RECEIVERGR-7000A(000-143-249)

B

ANLG基板ANLG BOARD14P0313A(1850W/WD)(000-141-995)14P0313B(1850WF/WDF)(000-141-994)

ﾗﾊ゙ ｷーー(E2)/(E2F)/(J2)/(J2F)RUBBER KEY (E2)/(E2F)/(J2)/(J2F)14-063-1003 (E)(100-270-610)-1850W/WD14-063-1004 (E)(100-270-620)-1850WF/WDF14-063-1043 (J)(100-270-773)-1850W/WD14-063-1044 (J)(100-270-783)-1850WF/WDF

PNL基板PNL BOARD14P0312(000-141-996)

ﾗﾊ゙ ｷーー (E1)/(J1)RUBBER KEY (E1)/(J1)14-063-1002(E)(100-270-600)14-063-1042(J)(100-270-764)

MAIN基板MAIN BOARD14P0311AW(1850W/WD NAVIONICS-E)(000-790-426)14P0311BW(1850WF/WDF NAVIONICS-E)(000-790-427)14P0311WC(1850W/WD NAVIONICS-J)(000-790-428)14P0311DW(1850WF/WDF NAVIONICS-J)(000-790-429)14P0311EW(1850W/WD C-MAP-E)(000-790-430)14P0311FW(1850WF/WDF C-MAP-E)(000-790-431)

LCD組品LCD ASSY.(004-378-840)

B

ﾊーﾄ゙ｶﾊ゙ 組ー品HARD COVER ASSY.GP-1850W/WD/WF/WDF(000-790-436)

Aパネル部組品FRONT PANEL ASSY.GP-1850W/WF(000-790-435)

F U R U N O Model GP-1850/D/F/DFUnit GPSプロッタ

電気部品表 GPS PLOTTERELECTRICAL PARTS LIST Ref.Dwg. C4395-K01-D Page

　2002年　9月 Blk.No. E-1SYMBOL TYPE CODE No. REMARKS SHIPPABLE

ASSEMBLY回路記号回路記号回路記号回路記号 型式型式型式型式 ｺｰﾄﾞ番号ｺｰﾄﾞ番号ｺｰﾄﾞ番号ｺｰﾄﾞ番号 備考備考備考備考 出荷単位組品出荷単位組品出荷単位組品出荷単位組品

PRINTED CIRCUIT BOARD プリント基板プリント基板プリント基板プリント基板1B1 14P0311A, MAIN 000-142-000 1850/D NAVIONICS-E X

14P0311B, MAIN 000-141-999 1850F/DF NAVIONICS-E X14P0311C, MAIN 000-141-998 1850/D NAVIONICS-J X14P0311D, MAIN 000-141-997 1850F/DF NAVIONICS-J X14P0311E, MAIN 000-145-130 1850/D C-MAP-E * X14P0311F, MAIN 000-145-129 1850F/DF C-MAP-E * X

1B2 14P0312, PNL 000-141-996 X1B3 14P0313A, ANLG 000-141-995 1850/D X

14P0313B, ANLG 000-141-994 1850F/DF X1B4 GN-7801A 000-143-245

or GN-7707 000-141-4081B7 GR-7000A 000-143-249 1850D/DF

or GN-8020 000-141-046

*: MAIN board for C-Map version will be available made-to-order basis.PANEL ASSEMBLY パネル組品パネル組品パネル組品パネル組品GP-1850/D-J 000-146-459 with rubber key XGP-1850/D-E 000-146-460 with rubber key XGP-1850F/DF-J 000-146-461 with rubber key XGP-1850F/DF-E 000-146-462 with rubber key XGP-1850/D/F/DF 000-146-463 BEZEL/FILTER ASSEMBLY X

LCD LCDLCDLCDLCD1B5 EDTCA0307CF, LCD 000-140-673

POWER SUPPLY ASSEMBLY 電源部組品電源部組品電源部組品電源部組品GP-1850 000-146-457 Power supply unit with ANLG boardGP-1850F 000-146-458 Power supply unit with ANLG board

F U R U N O Model GP-1850W/WD/WF/WDF

Unit GPSプロッタ

電気部品表 GPS PLOTTERELECTRICAL PARTS LIST Ref.Dwg. C4325-K01-A Page

　2002年　11月 Blk.No. E-2SYMBOL TYPE CODE No. REMARKS SHIPPABLE

ASSEMBLY

回路記号 型式 ｺｰﾄﾞ番号 備考 出荷単位組品

PRINTED CIRCUIT BOARD プリント基板

1B1 14P0311AW, MAIN 000-790-426 1850W/WD NAVIONICS-E

14P0311BW, MAIN 000-790-427 1850WF/WDF NAVIONICS-E

14P0311CW, MAIN 000-790-428 1850W/WD NAVIONICS-J

14P0311DW, MAIN 000-790-429 1850WF/WDF NAVIONICS-J

14P0311EW, MAIN 000-790-430 1850W/WD C-MAP-E *

14P0311FW, MAIN 000-790-431 1850WF/WDF C-MAP-E *

1B2 14P0312, PNL 000-141-996

1B3 14P0313A, ANLG-A 000-141-995 1850W/WD

14P0313B, ANLG-B 000-141-994 1850WF/WDF

1B4 GN-8091C 000-145-613

1B7 GR-7000A 000-143-249 1850WD/WDF

1850W/WF(option)

*: MAIN board for C-Map version will be available made-to-order basis.

PANEL ASSEMBLY パネル組品

GP-1850W/WF 000-790-435

LCD　ASSEMBLY LCD組品

1B5 GP-1850W/WD/WF/WDF 004-378-840

CB

1

A

34

2

名称

MASS

kg

相互結線図

INTERCONNECTIONDIAGRAM

ANTENNAUNIT

空中線部

0.2m,φ5.3

シロクロキ

NC

WHTBLKYELGRN

ミド

654321J6

PP

MJ-A6SPF

NMEA0183Ver2.0/1.5

TD-A

TD-B

RD-H

RD-C

SHIELD

*3

MJ-A6SPF0007,10m

MJ-A6SPF0012,5/10m

MJ-A6SPF0011,5/10m

MJ-A6SPF003,5m,φ6

7654321

キYEL

J5

SHIELDSD SGNCRDNCNC

アカRED

アオBLU

RS-232C

RDSDMJ-A7SPF0003,5m

DGPSBEACONRECEIVER

DGPSビーコン受信機

SHIELD

P

PRS-232C

RTCM104

NMEA0183Ver1.5/2.0

MJ-A7SPFD

J7

*2TNC-P-3

ANT

GPA-019

GPA-017

10m,φ5.3

12-24VDC

1 2 3(-)

(+)

SHIELDJ3

*3

220/230VAC,

50/60Hz,1φ

100/110(115)/

12-24VDC

MJ-A3SPFD

（＋）（－）

１２

５６

DPYC-1.5*1

PR-62

RECTIFIER

整流器

*2

クロ

シロWHTBLK

IV-8SQ*1

MJ-A3SPF0013,3.5m,φ8.0

*1IV-1.25SQ.

GND

SCALE

APPROVED

CHECKED

DRAWN

DWG.No.

TITLE

NAME

NMEA

DGPS

DISPLAYUNIT

指示器

GP-1850W/1850WD

(GP-1850W)

(GP-1850WD)

GPS/DGPSプロッタ

GPS/DGPSPLOTTER

NOTE*1.LOCALSUPPLY.

*2.OPTION.

*3.FITTEDATFACTORY.

*4.OPTIONALLEVELCONVERTERREQUIREDFORCURRENTLOOPORRS422OUTPUT.

NMEA0183inRS232CLEVEL*4

注記

＊３）コネクタは工場にて取付済み。

＊２）オプション。

＊１）現地手配。

＊４）カレントループ、RS-422の接続にはオプションのレベル変換器が必要。

GP-1850W/WD

*3

GPA-019S

*2

GPA-017S(GP-1850W)

(GP-1850WD)

N-P-8DFB

NJTP-3DXV-11m,φ5.3

N-J-3*2*3

TNC-P-3

TNC-J-3*3

NJTP-3DXV-11m,φ5.3

N-J-3

N-P-8DFB

*2*3

*3

8D-FB-CV

30/50m

*2

TNC-P-3

TNC-J-3*3

TNC-PS-3D,15m,φ5.3

5A

Aug.24,'04E.MIYOSHI

TAKAHASHI.T

C4425-C01-C

CB

1

A

34

2

名称

MASS

kg

相互結線図

INTERCONNECTIONDIAGRAM

ANTENNAUNIT

空中線部

0.2m,φ5.3

GPS/DGPSプロッタ魚探

GPS/DGPSPLOTTER/SOUNDER

シロクロキ

NC

WHTBLKYELGRN

ミド

654321J6

PP

MJ-A6SPF

NMEA0183Ver2.0/1.5

TD-A

TD-B

RD-H

RD-C

SHIELD

*3

MJ-A6SPF0007,10m

MJ-A6SPF0012,5/10m

MJ-A6SPF0011,5/10m

MJ-A6SPF003,5m,φ6

7654321

キYEL

J5

SHIELDSD SGNCRDNCNC

アカRED

アオBLU

RS-232C

RDSDMJ-A7SPF0003,5m

DGPSBEACONRECEIVER

DGPSビーコン受信機

SHIELD

P

PRS-232C

RTCM104

NMEA0183Ver1.5/2.0

MJ-A7SPFD

J7

*2TNC-P-3

ANT

GPA-019 (GP-1850WDF)

GPA-017 (GP-1850WF)

10m,φ5.3

12-24VDC

1 2 3(-)(+)

SHIELDJ3

*3

220/230VAC,

50/60Hz,1φ

100/110(115)/

12-24VDC

MJ-A3SPFD

（＋）（－）

１２

５６

DPYC-1.5*1

PR-62

RECTIFIER

整流器

*2

クロシロWHTBLK

IV-8SQ*1

MJ-A3SPF0013,3.5m,φ8.0

654321

NC

SHIELDTEMP

SPD

+12V

TEMP0V/SPDJ9

MJ-A6SPFD

T-02MTB

水温・船速ｾﾝｻｰ

TEMP/SPEEDSENSOR

7654321 8 9 10

MJ-A10SPFD

XDR-SHIELD

XDR-M

XDR-P

12V-P

GND

TEMP NCNCSPD

GNDJ2

送受波器

水温・船速ｾﾝｻｰ付

TRANSDUCERW/

TEMP/SPEEDSENSOR

525ST-PWD

525ST-MSD

T-02MSB

T-03MSB

ST-02PSB

ST-02MSB

*1IV-1.25SQ.

GND

SCALE

APPROVED

CHECKED

DRAWN

DWG.No.

TITLE

NAME

XDR

NMEA

DGPS

SPD/TEMP

DISPLAYUNIT

指示器

GP-1850WF/WDF

*3

GP-1850WF/1850WDF

GPA-019S

*2

GPA-017S(GP-1850WF)

(GP-1850WDF)

520-5PWD

520-5PSD

520-5MSD

送受波器

TRANSDUCER

10m(1kW)

50/200-1T

452

31

MB-10003

21

02S4092-0,8m

クロ

シロWHT

BLK BLU

GRN

BLKRED

アオミド

クロアカTB2

TB1

N-P-8DFB

NJTP-3DXV-11m,φ5.3

N-J-3*2*3

TNC-P-3

TNC-J-3*3

NJTP-3DXV-11m,φ5.3

N-J-3

N-P-8DFB

*2*3

*3

8D-FB-CV

30/50m

*2

TNC-P-3

TNC-J-3*3

TNC-PS-3D,15m,φ5.3

NOTE*1.LOCALSUPPLY.

*2.OPTION.

*3.FITTEDATFACTORY.

注記

＊３）コネクタは工場にて取付済み。

＊２）オプション。

＊１）現地手配。

＊４）カレントループ、RS-422の接続にはオプションのレベル変換器が必要。

*4.OPTIONALLEVELCONVERTERREQUIREDFORCURRENTLOOPORRS422OUTPUT.

NMEA0183inRS232CLEVEL*4

5A

Aug.24,'04E.MIYOSHI

TAKAHASHI.T

C4425-C02-C