Graco FRP Systems y RS Guns

L.A. TEJADA S.A.S28 AÑOS DE EXPERIENCIA

• RESINAS POLIESTER• FIBRA DE VIDRIO• CATALIZADORES• ACELERANTES• HERRAMIENTAS• DESMOLDANTES• EQUIPOS• REPUESTOS Y MANTENIMIENTOS• POLYUREAS

FRP Gel Proportioner

• Best spray pattern

• No surge bottle

• Very little assembly required

• One user interface

• Less maintenance than competition

FRP Chop Proportioner

• Very little assembly required –spend more time with your customer training

• No need for a surge bottle –fewer repair parts, less solvent & less resin used to prime

• Light weight balanced cart –small shop footprint, easy to maneuver

• New roving management –Better guides, less tangling, more uptime!

NXT Pump

• Truly engineered linkage design –Superior ratio control means less soft spots, quicker cure times, better quality end product

• Longer life components –longer lasting seals, more time between planned maintenance

• NXT Pump / Balanced air motor –shortened pump stroke and equal output pressure results in more consistent spray pattern for better end-product

• Easy catalyst adjustment – tool-less infinite adjustment makes proper catalyst percentage easy so operator can ensure optimal results

• Catalyst gauge – easy to read gauge for verification of a consistent catalyst fluid flow to maximize cure rates

FRP Proportioner Summary

• Low cost of ownership– Graco proven quality; more uptime- longer lasting

seals; pumps last longer between planned maintenance – Quick setup; mostly assembled- spend time training!– Ease of maintenance- No surge bottle necessary!

(fewer repair parts, less solvent & less resin used to prime)

• Technology differentiation– Engineered for superior ratio control- less soft-spots means

quicker cure times, higher quality end-product! – Graco proven pump technology (NXT)- balanced air-motor results in

consistent spray pattern (superior end-product)– DataTrak™ upgradable- Ensures quality, saves time & money!

(monitors resin usage, tracks cycles, displays flow rates)

Graco’s DataTrak™

DataTrak™ - Ensures quality, saves time & money!

Four Reasons to buy a Graco FRP System

Additional Accessories

• Adding accessories to FRP line

• Good way to increase revenue at same account

Viscon® Heaters

Accessories Impact

Graco RS Gun Overview

External Mix & Internal Mix

• External Mix RS Guns– Chemicals are mixed outside of the gun.– Used for gel coating and laminating.– No solvent flush required.

• Internal Mix RS Guns – Chemicals are mixed via static mixer inside the gun.– Generally used for laminating.– Requires solvent flushing.

14

What’s Different about the Graco RS Gun?

Innovative Design = Operator Productivity – Up to 44% lighter than the competition– AAC standard for superior spray patterns – Ergonomic handle for less fatigue – Compact hose configuration– Modular platform

Durability with Filled Materials– Reduced angled porting– Silicon nitride needles

Easy Maintenance – Break-away front head for easy maintenance– Pressure compensating packings– Needle springs are divorced from material (durability)– Needles do not require adjustment– Solvent resistant seals (whole gun can be submerged)

15

Key Features & Customer Why Buys

• Air Assist Containment (AAC) is standard on gel coat and chop guns

– Once only standard on gel coat guns and now standard on chop guns as well

– AAC develops a better spray pattern at lower fluid pressures.

– Operating at lower fluid pressures means less emissions, less overspray, and more material deposited on your target for a cleaner work environment and less material waste in overspray.

• Unique gun design eliminates the need to adjust replaced needles – All adjustments are done at our factory – not yours

– No more lost production time because of time spent adjusting needles to ensure that there are no lead-lag issues

– No more scrap parts due to incorrectly adjusted needles that allow catalyst to come out of the gun too soon or too late.

16

Unique needle clamping design ensures that both needles open and close the flow of chemical at the same time every time

17

Air Assist Containment (AAC)

•AAC is now standard on all RS guns

•Our exclusive AAC wraps the spray pattern in a containment shield of air - preventing atomized droplets from escaping the spray pattern

•AAC allows the mixed material to be dispensed at a lower velocity which dramatically reduces the chance of air entrapment or porosity

AAC Technology

Graco

Competitor

What’s Different with the Graco RS Cutter?

18

Ergonomic – Less Fatigue!– up to 40% Lighter

Performance – More output!– Up to 20% more glass (B-410)– Up to 18.2% more glass (MVP)– ½” air line

Easy Maintenance – Less Time! – Quick-Change blades

– Cartridge– Magnetic cutter drum

– Quick-Release anvil– External anvil adjustment– One hand speed control

Graco RS Gun‐ External line to air motor 

New air line directly to air motor• Increases air flow to motor• Increases glass output• Glass output of up to 14.5% better than current RS Gun @ 60 psi dynamic pressure• Glass output of up to 18.2% more than MVP@ 60 psi dynamic pressure

Graco RS Gun‐ External line to air motor 

New air line directly to air motor• Increases air flow to motor• Increases glass output• Up to 27% more glass output than MVP’s VRC 3000 Cutter*• Up to 19% more glass output than previous RS Gun design*

*Testing based on Graco FRP Chop with new ½ air line OD airline, 6‐blade cutter, 90 PSI Dynamic Air Pressure, 2 strands of glass.  Results will vary depending on set‐up (ie air pressure, hose length, tension settings, etc.)

Bendable Chutes now come standard on all Chop Guns.  Improved Aim for glass distribution. 

Graco RS Gun‐ Bendable Chutes 

Graco RS Gun‐ Additional Changes 

RS Cutter Assembly RevisionsPN Part Description Change Benefit

16P833  CLIP,WEAR,SACRIFICIAL,RS CHOP GUN New Part Protects cover from glass damage24F038 BAR, feed, cutter, 3‐hole Revised hole pattern Allows for optimal glass distribution from 1‐3 strands100639 WASHER, lock Serrated lock washer for cover knob Prevents cover accidentally coming off

Increased durability. 

Ease of use and flexibility.

NEW RS CHOP GUN‐ “High‐Flow / Heavy Fill” Internal Mix 

New versions of RS Chop Gun for Hi-Flow & Heavy Fill applications • PN 24P435: High Flow Internal Mix Gun with Cutter• PN 24P436:  High Flow Internal Mix Gun without Cutter

• Do not have to separately order Internal Mix High-Flow Kit (PN 24H337)• Do not have to separately order Carbide Resin Seat (PN 24M833)• New handle air ports and external air line to air motor

Four Reasons to buy a Graco RS Gun…

Reactor 2 E-XP2

EQUIPOS PARA POLIURETANO Y POLYUREAS

Count on the Reactor 2 E-XP2 proportioner for advanced technology in applying fast-curing polyurea coatings. Because it's a Reactor 2 series proportioner, it offers software and hardware enhancements for better spray performance, plus technologies that add to your bottom line.

Reactor E-10

EQUIPOS PARA POLIURETANO Y POLYUREAS

Small size is ideal for on-site portability and hard-to-reach areasOne-person operation saves time and moneyUse as an add-on to your existing spray businessVersatile - switch from cold spray to hot spray to foamSaves 30% on material costs compared to disposable foam systems