65
Grid-Lok Selection matrix
Grid-Lok Selection matrix
Grid-Lok spares
Flying probe testing
Pick & place
Stencil printing
Process selection
ASM DEK Ekra
Ersa Juki GKG
MPM Panasonic
Speedprint Yamaha
Stencil printing
ASM Siplace Assembleon
Fuji I-Pulse
Juki Panasonic
Samsung Universal
Pick & place
Yamaha
SPEA
Itochu-Takaya
Flying probe testing
Sensors
Pin-Lok (pin in paste)
Pin repair kits
Fittings
Controllers
Top caps
Others
Grid-Lok Spares
All DEK with squeegees
All DEK with ProFlow
ASM DEK
Ekra
All Ekra printers
Ersa
All Ersa Versaprint
Juki GKG
GL, K3, Pmax printers
MPM
Momentum, Accela, Accuflex
Panasonic
All SP series
Speedprint
All SP series
Yamaha
YSP printers
YCP printers
HS50
HS60
X2, X4, SX4
SX1, SX2
F series
C series
S series
D series
ASM Siplace
Assembleon
AX-201
I-Flex dual
GEM Series
I-Flex single
Fuji
NXT M3
NXT M3 dual
NXT M6
NXT M6 dual
I-Pulse
M Series
Juki
FX 1
FX 2
FX 3
KE
JX
Panasonic
NPM-W
NPM-D
Samsung
CP 45
SM 471
SM 481
CP 20
SM 421
SM 482
GC-60D
GC-120Q
AC-15S
AC-30S
GX-11S
GC-30S
GX-11D
GI-14D
AI-07S
AC-90T
Universal
YS100
YS12P
YS24 YS12
YG12 YS24X
YS12F
YG12F
YS88
Yamaha
Off line machines In line machines
Grid-Lok MaxTM
for Itochu-Takaya
Itochu-Takaya
SPEA
Grid-Lok MaxTM
for SPEA
KIT_111 (full kit with no modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
ASM DEK (squeegees)
GHD8112 (Gold modules 12”)
Length: 305mm (12”)
Width: 32mm
Height (pins set): 81mm
Height (pins reset): 60mm
Pins count: 46
INTEGRATION
The full kit consists of KIT_111 plus the desired number of modules described here.
No board lifters needed.
077_SBA optical sensor needed only if pins should raise in print height.
GHD8118 (Gold modules 18”)
Length: 457mm (12”)
Width: 32mm
Height (pins set): 81mm
Height (pins reset): 60mm
Pins count: 70
OR
+
ASM DEK (ProFlow)
KIT_111 (full kit with no modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
GHD8712 (Gold modules 12”)
Length: 305mm (12”)
Width: 32mm
Height (pins set): 87mm
Height (pins reset): 60mm
Pins count: 46
+
GHD8718 (Gold modules 18”)
Length: 457mm (12”)
Width: 32mm
Height (pins set): 87mm
Height (pins reset): 60mm
Pins count: 70
OR
INTEGRATION
The full kit consists of KIT_111 plus the desired number of modules described here.
No board lifters needed.
077_SBA optical sensor needed only if pins should raise in print height.
Ekra
KIT_111 (full kit with no modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
GHD8712 (Gold modules 12”)
Length: 305mm (12”)
Width: 32mm
Height (pins set): 87mm
Height (pins reset): 60mm
Pins count: 46
INTEGRATION
The full kit consists of KIT_111 plus the desired number of modules described here.
087_BLA board lifters needed.
077_SBA optical sensor needed.
GHD8718 (Gold modules 18”)
Length: 457mm (12”)
Width: 32mm
Height (pins set): 87mm
Height (pins reset): 60mm
Pins count: 70
OR
+
087_BLA
077_SBA
+
Ersa
KIT_111 (full kit with no modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
GHD9812 (Gold modules 12”)
Length: 305mm (12”)
Width: 32mm
Height (pins set): 98mm
Height (pins reset): 71mm
Pins count: 46
INTEGRATION
The full kit consists of KIT_111 plus the desired number of modules described here.
No board lifters needed.
077_SBA optical sensor needed.
GHD9818 (Gold modules 18”)
Length: 457mm (12”)
Width: 32mm
Height (pins set): 98mm
Height (pins reset): 71mm
Pins count: 70
OR
+
077_SBA
+
Juki GKG
KIT_111 (full kit with no modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
GHD6512 (Gold modules 12”)
Length: 305mm (12”)
Width: 32mm
Height (pins set): 65mm
Height (pins reset): 47mm
Pins count: 46
GHD6518 (Gold modules 18”)
Length: 457mm (12”)
Width: 32mm
Height (pins set): 65mm
Height (pins reset): 47mm
Pins count: 70
OR
+
077_SBA
+
INTEGRATION
The full kit consists of KIT_111 plus the desired number of modules described here.
No board lifters needed.
077_SBA optical sensor needed.
MPM
KIT_111 (full kit with no modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
GHD3912 (Gold modules 12”)
Length: 305mm (12”)
Width: 32mm
Height (pins set): 39mm
Height (pins reset): 26mm
Pins count: 46
GHD3918 (Gold modules 18”)
Length: 457mm (12”)
Width: 32mm
Height (pins set): 39mm
Height (pins reset): 26mm
Pins count: 70
OR
+
077_SBA
+
INTEGRATION
The full kit consists of KIT_111 plus the desired number of modules described here.
No board lifters needed.
077_SBA optical sensor needed.
Panasonic
KIT_111 (full kit with no modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
GHD4112 (Gold modules 12”)
Length: 305mm (12”)
Width: 32mm
Height (pins set): 41mm
Height (pins reset): 28mm
Pins count: 46
GHD4118 (Gold modules 18”)
Length: 457mm (12”)
Width: 32mm
Height (pins set): 41mm
Height (pins reset): 28mm
Pins count: 70
OR
+
041_BLA
077_SBA
+
INTEGRATION
The full kit consists of KIT_111 plus the desired number of modules described here.
041_BLA board lifters needed.
077_SBA optical sensor needed.
Speedprint
KIT_111 (full kit with no modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
GHD5912 (Gold modules 12”)
Length: 305mm (12”)
Width: 32mm
Height (pins set): 59mm
Height (pins reset): 45mm
Pins count: 46
GHD5918 (Gold modules 18”)
Length: 457mm (12”)
Width: 32mm
Height (pins set): 59mm
Height (pins reset): 45mm
Pins count: 70
OR
+
077_SBA
+
INTEGRATION
The full kit consists of KIT_111 plus the desired number of modules described here.
No board lifters needed.
077_SBA optical sensor needed.
Yamaha YSP
KIT_111 (full kit with no modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
GHD6712 (Gold modules 12”)
Length: 305mm (12”)
Width: 32mm
Height (pins set): 67mm
Height (pins reset): 49mm
Pins count: 46
GHD6718 (Gold modules 18”)
Length: 457mm (12”)
Width: 32mm
Height (pins set): 67mm
Height (pins reset): 49mm
Pins count: 70
OR
+
+ 067_BLA
INTEGRATION
The full kit consists of KIT_111 plus the desired number of modules described here.
067_BLA board lifters needed.
No optical sensor needed.
Yamaha YCP
KIT_111 (full kit with no modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
INTEGRATION
The full kit consists of KIT_111 plus the desired number of modules described here.
067_BLA board lifters needed.
No optical sensor needed.
The manual modules are installed stand alone on the machine table.
077_SBA
+
GMD6714M (Silver manual modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 67mm
Height (pins reset): 50mm
Pins count: 27
GMD6714AM (Silver hybrid modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 67mm
Height (pins reset): 50mm
Pins count: 27
OR
+
GMD7714M (Silver manual modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 77mm
Height (pins reset): 60mm
Pins count: 27
ASM Siplace F, C, S, HS50 series
KIT_111 (full kit with no modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
INTEGRATION
The full automatic kit consists of KIT_111 plus the desired number of modules described here.
No board lifters needed.
077_SBA optical sensor needed.
The manual modules are installed stand alone on the machine table.
GMD7714A (Silver automatic modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 77mm
Height (pins reset): 60mm
Pins count: 27
+
077_SBA
+
ASM Siplace SX1, SX2, D series (single table)
GMD9714M (Silver manual modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 97mm
Height (pins reset): 80mm
Pins count: 27
KIT_111 (full kit with no modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
INTEGRATION
The full automatic kit consists of KIT_111 plus the desired number of modules described here.
No board lifters needed.
077_SBA optical sensor needed.
The manual modules are installed stand alone on the machine table.
GMD9714A (Silver automatic modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 97mm
Height (pins reset): 80mm
Pins count: 27
+
077_SBA
+
KIT_211 (full dual kit with no modules)
12 x twin leashes with fittings, for connecting the modules
211_CTL – dual table controller
2 x 006_MAN – manifold
001_DCP – Power supply 230V/24V
Air filter regulator
All necessary tubes and air pipes for kit installation
ASM Siplace SX1, SX2, D series (dual table)
GMD9714M (Silver manual modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 97mm
Height (pins reset): 80mm
Pins count: 27
INTEGRATION
The full automatic kit consists of KIT_211 plus the desired number of modules described here. This kit is capable to coordinate the modules from two independent tables.
No board lifters needed.
2 x 077_SBA optical sensor needed.
The manual modules are installed stand alone on the machine table.
GMD9714A (Silver automatic modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 97mm
Height (pins reset): 80mm
Pins count: 27
+
2 x 077_SBA
+
ASM Siplace X, SX4, HS60 series (four tables)
GMD9714M (Silver manual modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 97mm
Height (pins reset): 80mm
Pins count: 27
INTEGRATION
The full automatic kit consists of 2 x KIT_211 plus the desired number of modules described here. This kit is capable to coordinate the modules from two independent tables.
No board lifters needed.
4 x 077_SBA optical sensor needed.
The manual modules are installed stand alone on the machine table.
GMD9714A (Silver automatic modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 97mm
Height (pins reset): 80mm
Pins count: 27
+
4 x 077_SBA
+
2 x KIT_211 (full dual kit with 0 modules)
12 x twin leashes with fittings, for connecting the modules
211_CTL – dual table controller
2 x 006_MAN – manifold
001_DCP – Power supply 230V/24V
Air filter regulator
All necessary tubes and air pipes for kit installation
Assembleon I-Flex (single table)
GMD1354M (Silver manual modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 135mm
Height (pins reset): 118mm
Pins count: 27
KIT_111 (full kit with no modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
INTEGRATION
The full automatic kit consists of KIT_111 plus the desired number of modules described here.
No board lifters needed.
077_SBA optical sensor needed.
The manual modules are installed stand alone on the machine table.
GMD1354A (Silver automatic modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 135mm
Height (pins reset): 118mm
Pins count: 27
+
077_SBA
+
Assembleon I-Flex (dual table)
KIT_211 (full dual kit with no modules)
12 x twin leashes with fittings, for connecting the modules
211_CTL – dual table controller
2 x 006_MAN – manifold
001_DCP – Power supply 230V/24V
Air filter regulator
All necessary tubes and air pipes for kit installation
INTEGRATION
The full automatic kit consists of KIT_211 plus the desired number of modules described here. This kit is capable to coordinate the modules from two independent tables.
No board lifters needed.
2 x 077_SBA optical sensor needed.
The manual modules are installed stand alone on the machine table.
+
2 x 077_SBA
+
GMD1354M (Silver manual modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 135mm
Height (pins reset): 118mm
Pins count: 27
GMD1354A (Silver automatic modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 135mm
Height (pins reset): 118mm
Pins count: 27
Assembleon GEM
GMD6914M (Silver manual modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 69mm
Height (pins reset): 52mm
Pins count: 27
KIT_111 (full kit with no modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
INTEGRATION
The full automatic kit consists of KIT_111 plus the desired number of modules described here.
No board lifters needed.
077_SBA optical sensor needed.
The manual modules are installed stand alone on the machine table.
GMD6914A (Silver automatic modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 69mm
Height (pins reset): 52mm
Pins count: 27
+
077_SBA
+
Assembleon AX-201
GMD1154M (Silver manual modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 115mm
Height (pins reset): 98mm
Pins count: 27
KIT_111 (full kit with no modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
INTEGRATION
The full automatic kit consists of KIT_111 plus the desired number of modules described here.
No board lifters needed.
077_SBA optical sensor needed.
The manual modules are installed stand alone on the machine table.
GMD1154A (Silver automatic modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 115mm
Height (pins reset): 98mm
Pins count: 27
+
077_SBA
+
Fuji NXT M3
GMD5310M (Silver manual modules 10”)
Length: 254mm (10”)
Width: 32mm
Height (pins set): 53mm
Height (pins reset): 36mm
Pins count: 19
KIT_111 (full kit with no modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
INTEGRATION
The full automatic kit consists of KIT_111 plus the desired number of modules described here.
No board lifters needed.
077_SBA optical sensor needed.
The manual modules are installed stand alone on the machine table.
GMD5310A (Silver automatic modules 10”)
Length: 254mm (10”)
Width: 32mm
Height (pins set): 53mm
Height (pins reset): 36mm
Pins count: 19
+
077_SBA
+
Fuji NXT M3 (dual lane)
KIT_211 (full dual kit with no modules)
12 x twin leashes with fittings, for connecting the modules
211_CTL – dual table controller
2 x 006_MAN – manifold
001_DCP – Power supply 230V/24V
Air filter regulator
All necessary tubes and air pipes for kit installation
INTEGRATION
The full automatic kit consists of KIT_211 plus the desired number of modules described here. This kit is capable to coordinate the modules from two independent tables.
No board lifters needed.
2 x 077_SBA optical sensor needed.
The manual modules are installed stand alone on the machine table.
+
2 x 077_SBA
+
GMD5310M (Silver manual modules 10”)
Length: 254mm (10”)
Width: 32mm
Height (pins set): 53mm
Height (pins reset): 36mm
Pins count: 19
GMD5310A (Silver automatic modules 10”)
Length: 254mm (10”)
Width: 32mm
Height (pins set): 53mm
Height (pins reset): 36mm
Pins count: 19
Fuji NXT M6
GMD5314M (Silver manual modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 53mm
Height (pins reset): 36mm
Pins count: 27
KIT_111 (full kit with no modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
INTEGRATION
The full automatic kit consists of KIT_111 plus the desired number of modules described here.
No board lifters needed.
077_SBA optical sensor needed.
The manual modules are installed stand alone on the machine table.
GMD5314A (Silver automatic modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 53mm
Height (pins reset): 36mm
Pins count: 27
+
077_SBA
+
Fuji NXT M6 (dual lane)
KIT_211 (full dual kit with no modules)
12 x twin leashes with fittings, for connecting the modules
211_CTL – dual table controller
2 x 006_MAN – manifold
001_DCP – Power supply 230V/24V
Air filter regulator
All necessary tubes and air pipes for kit installation
INTEGRATION
The full automatic kit consists of KIT_211 plus the desired number of modules described here. This kit is capable to coordinate the modules from two independent tables.
No board lifters needed.
2 x 077_SBA optical sensor needed.
The manual modules are installed stand alone on the machine table.
+
2 x 077_SBA
+
GMD5314M (Silver manual modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 53mm
Height (pins reset): 36mm
Pins count: 27
GMD5314A (Silver automatic modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 53mm
Height (pins reset): 36mm
Pins count: 27
I-Pulse
GMD7014M (Silver manual modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 70mm
Height (pins reset): 52mm
Pins count: 27
KIT_111 (full kit with no modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
INTEGRATION
The full automatic kit consists of KIT_111 plus the desired number of modules described here.
No board lifters needed.
077_SBA optical sensor needed.
The manual modules are installed stand alone on the machine table.
GMD7014A (Silver automatic modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 70mm
Height (pins reset): 53mm
Pins count: 27
+
077_SBA
+
Juki FX-1, FX-2, KE, JX
GMD9714M (Silver manual modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 97mm
Height (pins reset): 80mm
Pins count: 27
KIT_111 (full kit with no modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
INTEGRATION
The full automatic kit consists of KIT_111 plus the desired number of modules described here.
No board lifters needed.
077_SBA optical sensor needed.
The manual modules are installed stand alone on the machine table.
GMD9714A (Silver automatic modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 97mm
Height (pins reset): 80mm
Pins count: 27
+
077_SBA
+
Juki FX-3 (dual table)
KIT_211 (full dual kit with no modules)
12 x twin leashes with fittings, for connecting the modules
211_CTL – dual table controller
2 x 006_MAN – manifold
001_DCP – Power supply 230V/24V
Air filter regulator
All necessary tubes and air pipes for kit installation
GMD9714M (Silver manual modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 97mm
Height (pins reset): 80mm
Pins count: 27
INTEGRATION
The full automatic kit consists of KIT_211 plus the desired number of modules described here. This kit is capable to coordinate the modules from two independent tables.
No board lifters needed.
2 x 077_SBA optical sensor needed.
The manual modules are installed stand alone on the machine table.
GMD9714A (Silver automatic modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 97mm
Height (pins reset): 80mm
Pins count: 27
+
2 x 077_SBA
+
Panasonic NPM-W
GMD7014M (Silver manual modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 70mm
Height (pins reset): 52mm
Pins count: 27
KIT_111 (full kit with no modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
INTEGRATION
The full automatic kit consists of KIT_111 plus the desired number of modules described here.
No board lifters needed.
077_SBA optical sensor needed.
The manual modules are installed stand alone on the machine table.
GMD7014A (Silver automatic modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 70mm
Height (pins reset): 53mm
Pins count: 27
+
077_SBA
+
Panasonic NPM-D (dual lane)
KIT_211 (full dual kit with no modules)
12 x twin leashes with fittings, for connecting the modules
211_CTL – dual table controller
2 x 006_MAN – manifold
001_DCP – Power supply 230V/24V
Air filter regulator
All necessary tubes and air pipes for kit installation
INTEGRATION
The full automatic kit consists of KIT_211 plus the desired number of modules described here. This kit is capable to coordinate the modules from two independent tables.
No board lifters needed.
2 x 077_SBA optical sensor needed.
The manual modules are installed stand alone on the machine table.
+
2 x 077_SBA
+
GMD7014M (Silver manual modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 70mm
Height (pins reset): 52mm
Pins count: 27
GMD7014A (Silver automatic modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 70mm
Height (pins reset): 53mm
Pins count: 27
Samsung CP-20, CP-45, SM-421
GMD1324M (Silver manual modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 132mm
Height (pins reset): 115mm
Pins count: 27
KIT_111 (full kit with no modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
INTEGRATION
The full automatic kit consists of KIT_111 plus the desired number of modules described here.
No board lifters needed.
077_SBA optical sensor needed.
The manual modules are installed stand alone on the machine table.
GMD1324A (Silver automatic modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 132mm
Height (pins reset): 115mm
Pins count: 27
+
077_SBA
+
Samsung SM-471
KIT_211 (full dual kit with no modules)
12 x twin leashes with fittings, for connecting the modules
211_CTL – dual table controller
2 x 006_MAN – manifold
001_DCP – Power supply 230V/24V
Air filter regulator
All necessary tubes and air pipes for kit installation
INTEGRATION
The full automatic kit consists of KIT_211 plus the desired number of modules described here. This kit is capable to coordinate the modules from two independent tables.
No board lifters needed.
2 x 077_SBA optical sensor needed.
The manual modules are installed stand alone on the machine table.
+
2 x 077_SBA
+
GMD1344M (Silver manual modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 134mm
Height (pins reset): 117mm
Pins count: 27
GMD1344A (Silver automatic modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 134mm
Height (pins reset): 117mm
Pins count: 27
Samsung SM-481, SM-482
GMD1344M (Silver manual modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 134mm
Height (pins reset): 117mm
Pins count: 27
KIT_111 (full kit with no modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
INTEGRATION
The full automatic kit consists of KIT_111 plus the desired number of modules described here.
No board lifters needed.
077_SBA optical sensor needed.
The manual modules are installed stand alone on the machine table.
GMD1344A (Silver automatic modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 134mm
Height (pins reset): 117mm
Pins count: 27
+
077_SBA
+
Universal GX-11S, GC-30S, GX-11D, GI-14D, GC-60D, AC-15S,
AC-30S, AI-07S
GMD5714M (Silver manual modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 57mm
Height (pins reset): 40mm
Pins count: 27
KIT_111 (full kit with no modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
INTEGRATION
The full automatic kit consists of KIT_111 plus the desired number of modules described here.
No board lifters needed.
077_SBA optical sensor needed.
The manual modules are installed stand alone on the machine table.
GMD5714A (Silver automatic modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 57mm
Height (pins reset): 40mm
Pins count: 27
+
077_SBA
+
Universal AC-90T, GC-120Q (dual table)
KIT_211 (full dual kit with no modules)
12 x twin leashes with fittings, for connecting the modules
211_CTL – dual table controller
2 x 006_MAN – manifold
001_DCP – Power supply 230V/24V
Air filter regulator
All necessary tubes and air pipes for kit installation
INTEGRATION
The full automatic kit consists of KIT_211 plus the desired number of modules described here. This kit is capable to coordinate the modules from two independent tables.
No board lifters needed.
2 x 077_SBA optical sensor needed.
The manual modules are installed stand alone on the machine table.
+
2 x 077_SBA
+
GMD5714M (Silver manual modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 57mm
Height (pins reset): 40mm
Pins count: 27
GMD5714A (Silver automatic modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 57mm
Height (pins reset): 40mm
Pins count: 27
Yamaha YS12, YS12F, YS12P, YS88, YS100, YG12, YG12F
GMD7614M (Silver manual modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 76mm
Height (pins reset): 59mm
Pins count: 27
KIT_111 (full kit with no modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
INTEGRATION
The full automatic kit consists of KIT_111 plus the desired number of modules described here.
No board lifters needed.
077_SBA optical sensor needed.
The manual modules are installed stand alone on the machine table.
GMD7614A (Silver automatic modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 76mm
Height (pins reset): 59mm
Pins count: 27
+
077_SBA
+
Yamaha YS24, YS24X (dual table)
KIT_211 (full dual kit with no modules)
12 x twin leashes with fittings, for connecting the modules
211_CTL – dual table controller
2 x 006_MAN – manifold
001_DCP – Power supply 230V/24V
Air filter regulator
All necessary tubes and air pipes for kit installation
INTEGRATION
The full automatic kit consists of KIT_211 plus the desired number of modules described here. This kit is capable to coordinate the modules from two independent tables.
No board lifters needed.
2 x 077_SBA optical sensor needed.
The manual modules are installed stand alone on the machine table.
+
2 x 077_SBA
+
GMD7610M (Silver manual modules 10”)
Length: 254mm (10”)
Width: 32mm
Height (pins set): 76mm
Height (pins reset): 59mm
Pins count: 19
GMD7610AM (Silver hybrid modules 10”)
Length: 254mm (10”)
Width: 32mm
Height (pins set): 76mm
Height (pins reset): 59mm
Pins count: 19
Itochu-Takaya (in line machines)
KIT_111 (full kit with no
modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
GHD6212 (Gold modules 12”)
Length: 305mm (12”)
Width: 32mm
Height (pins set): 62mm
Height (pins reset): 44mm
Pins count: 46
+
GHD6218 (Gold modules 18”)
Length: 457mm (12”)
Width: 32mm
Height (pins set): 62mm
Height (pins reset): 44mm
Pins count: 70
OR
INTEGRATION
The full kit consists of KIT_111 plus the desired number of modules described here.
No board lifters needed.
No optical sensor needed.
GMD6214A (Silver modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 62mm
Height (pins reset): 45mm
Pins count: 27
OR
Itochu-Takaya (off line machines)
KIT_111 (full kit with no
modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
GHD9812 (Gold modules 12”)
Length: 305mm (12”)
Width: 32mm
Height (pins set): 98mm
Height (pins reset): 71mm
Pins count: 46
+
GHD9818 (Gold modules 18”)
Length: 457mm (12”)
Width: 32mm
Height (pins set): 98mm
Height (pins reset): 71mm
Pins count: 70
OR
INTEGRATION
The full kit consists of KIT_111 plus the desired number of modules described here.
No board lifters needed.
077_SBA optical sensor needed.
GMD9814A (Silver modules 14”)
Length: 355mm (14”)
Width: 32mm
Height (pins set): 98mm
Height (pins reset): 81mm
Pins count: 27
OR
Itochu-Takaya (Grid-Lok MaxTM for off line machines)
KIT_111 (full kit with no modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
GLM9812 (Gold Max modules 12”)
Length: 305mm (12”)
Width: 32mm
Height (pins set): 98mm
Height (pins reset): 58mm
Pins count: 46
INTEGRATION
The full kit consists of KIT_111 plus the desired number of modules described here.
No board lifters needed.
077_SBA optical sensor needed.
GLM9818 (Gold Max modules 18”)
Length: 457mm (12”)
Width: 32mm
Height (pins set): 98mm
Height (pins reset): 58mm
Pins count: 70
OR
+
077_SBA
+
SPEA (Grid-Lok MaxTM)
KIT_111 (full kit with no modules)
6 x twin leashes with fittings, for connecting the modules
111_CTL – single table controller
006_MAN – manifold for 6 modules
001_DCP – Power supply 230V/24V
002_CON – Remote control unit
Air filter regulator
All necessary tubes and air pipes for kit installation
GLM1012 (Gold Max modules 12”)
Length: 305mm (12”)
Width: 32mm
Height (pins set): 110mm
Height (pins reset): 70mm
Pins count: 46
INTEGRATION
The full kit consists of KIT_111 plus the desired number of modules described here.
No board lifters needed.
077_SBA optical sensor needed.
GLM1018 (Gold Max modules 18”)
Length: 457mm (12”)
Width: 32mm
Height (pins set): 110mm
Height (pins reset): 70mm
Pins count: 70
OR
+
077_SBA
+
Part No. Description Top caps
025_TIP 25 Rubber Compliant Top Caps for GSX
100_TIP 100 Rubber Compliant Top Caps for GSX
025_ETP 25 Rubber Compliant Top Caps (Exp)
025_UTP 25 Universal Compliant Caps for GHD
100_UTP 100 Universal Compliant Caps for GHD
025_TMP 25 Universal Compliant Caps for GMD
100_TMP 100 Universal Compliant Caps for GMD
025_TSP 25 Universal Compliant Caps for GHD 39mm
100_TSP 100 Universal Compliant Caps for GHD 39mm
Top caps, Pin repair kits, Sensors
Part No. Description Pin repair kits
018_PRK DEK, Ekra, Siemens, MPM Pin Repair Kit, 15 pins
881_PRK 81mm HD Grid-Lok Pin Repair Kit, 25 pins
887_PRK 87mm HD Grid-Lok Pin Repair Kit, 25 pins
009_PRK Grid-Lok Pin Repair Kit (75mm)
818_PRK Grid-Lok HD Pin Repair Kit (39mm), 10 pins
062_PRK Grid-Lok HD Pin Repair Kit (62mm), 25 pins
053_PRK Grid-Lok Silver Pin Repair Kit, 10 pins
Part No. Description Sensors
077_SBA Optical Sensor with Magnetic Base
002_SEN Grid_Lok Optical Sensor
003_SEN E3HT-DS3EZ Photoelectric Switch
Fittings, Controllers, Pin-Lok, Others
Part No. Description Controllers
111_CTL Single Grid-Lok controller
211_CTL Double Grid-Lok controller
103_VAL Valve inside control box 103_CTL
111_VAL Valve inside control box 111_CTL
103_PSI Pressure Sensor for 103_CTL
111_PSI Pressure Sensor for 111_CTL
103_PCB Programmed Circuit Board for 103_CTL
111_PCB Programmed Circuit Board for 111_CTL
211_PCB Programmed Circuit Board for 211_CTL
Part No. Description Others
006_MAN 6 Station Manifold Fully Fitted
002_STO Magnetic stand off for silver modules - pair
041_BLA 41mm board lifters set - Panasonic
067_BLA 67mm board lifters set - Yamaha
087_BLA 87mm board lifters set - Ekra
002_CON Grid-Lok Hand Held Controller (Mark 2)
001_DCP 24 Volt Power Supply
518_MAG 18" of Adhesive Magnetic Tape
Part No. Description Fittings
006_SMF 6 Female Silver Quick Connect
006_RMF 6 Female Red Quick Connect
006_AFT 90 Deg. X 1/4" Tube x 1/8" npt
006_FLO 90 Deg. X 1/4" Tube x 1/8" npt Flow Control
018_FLO Pack of 5 HD Grid-Lok Module Flow Controllers
005_LEA Twin Tubing w/ fittings, 5 pcs
005_SFT 5/32" Tube x 10-32 Thread Straight Fitting
005_AFT 5/32" Tube x 10-32 Thread 90 Deg. Fitting
Part No. Description Pin-Lok
010_PIP Pin in paste jig for a 10” silver module
012_PIP Pin in paste jig for a 12” gold module
014_PIP Pin in paste jig for a 14” silver module
018_PIP Pin in paste jig for a 18” gold module
