Do not operate this equipment unless youhave read and understood the contents ofthis manual! Failure to follow theinstructions contained in this manual mayresult in serious injury or death. Thismanual contains important safetyinformation concerning the maintenance,use, and operation of this product. Ifyou’re unable to understand the contentsof this manual, please bring it to theattention of your supervisor. Keep thismanual in a safe location for futurereference.
No opere este equipo al menos que hayaleído y comprendido el contenido de estemanual! Cualquier falla en el seguimientode las instrucciones contenidas en estemanual puede resultar en un serio lesióno muerte. Este manual contieneimportante información sobre seguridadconcerniente al mantenimiento, uso yoperación de este producto. Si usted nopuede entender el contenido de estemanual por favor pregunte a susupervisor. Almacenar este manual enuna localización segura para la referenciafutura.
Ne pas utiliser cet équipement sans avoirlu et compris le contenu de ce manuel !Le non-respect des instructionscontenues dans ce manuel peut entraînerde graves blessures ou la mort. Cemanuel contient des informationsimportantes concernant l'entretien,l'utilisation et le fonctionnement de ceproduit. Si vous ne comprenez pas lecontenu de ce manuel, veuillez le signalerà votre supérieur. Conservez ce manueldans un endroit sûr pour pouvoir vous yréférer plus tard.
WARNING ADVERTENCIA AVERTISSEMENT
CONTENTS
2Form No. GRSm-0711
INTRODUCTIONHatco Glo-Ray Heated Shelves are designed to keep preparedfoods hot in kitchen work areas, server pick-up stations, orcustomer serving points. Heated Shelves will keep all foods atoptimum serving temperatures without affecting quality. Thesewarmers have a thermostatically-controlled heated base toextend the holding times of most foods.
Glo-Ray Heated Shelves are a product of extensive researchand field testing. The materials used were selected formaximum durability, attractive appearance, and optimumperformance. Every unit is inspected and tested thoroughly priorto shipment.
This manual provides the installation, safety, and operatinginstructions for the Glo-Ray Heated Shelf. Hatco recommendsall installation, operating, and safety instructions appearing inthis manual be read prior to installation or operation of the Glo-Ray Heated Shelf.
Safety information that appears in this manual is identified bythe following signal word panels:
WARNING indicates a hazardous situation which, if notavoided, could result in death or serious injury.
CAUTION indicates a hazardous situation which, if notavoided, could result in minor or moderate injury.
NOTICE is used to address practices not related topersonal injury.
WARNING
NOTICE
CAUTION
Important Owner Information ..............................................2Introduction...........................................................................2Important Safety Information...............................................3Model Descriptions...............................................................4
GRS model ......................................................................4GRSB and GRSBF models .............................................4
Model Designation................................................................4Specifications........................................................................5
Troubleshooting Guide ......................................................17Options and Accessories...................................................17Limited Warranty.................................................................19Authorized Parts Distributors............................Back Cover
IMPORTANT OWNER INFORMATION
Record the model number, serial number (specification label onbottom of GRS model, bottom of control box on GRSB andGRSBF models), voltage, and purchase date of the unit in thespaces below. Please have this information available whencalling Hatco for service assistance.
model No. ____________________________________
Serial No. ____________________________________
Voltage ______________________________________
Date of Purchase ______________________________
Register your unit!Completing online warranty registration will prevent delay inobtaining warranty coverage. access the Hatco website atwww.hatcocorp.com, select the Parts & Service pull-downmenu, and click on “Warranty Registration”.
additional information can be found by visiting our web site atwww.hatcocorp.com.
24 Hour 7 Day Parts and ServiceAssistance available in the United Statesand Canada by calling (800) 558-0607.
IMPORTANT SAFETy INFORMATION
Form No. GRSm-0711 3
ELECTRIC SHOCK HAzARD:• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. Ifplug and receptacle do not match, contact a qualifiedelectrician to determine and install the proper voltageand size electrical receptacle.
• Turn OFF power switch, unplug power cord, and allowunit to cool before performing any cleaning,adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is notwaterproof. Do not operate if unit has been submergedor saturated with water.
• Unit is not weatherproof. Locate unit indoors whereambient air temperature is a minimum of 70°F (21°C).
• This unit is not “jet-proof” construction. Do not use jet-clean spray to clean this unit.
• Do not steam clean or use excessive water on unit.
• Do not pull unit by power cord.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged powercord. The cord must be replaced by Hatco, anAuthorized Hatco Service Agent, or a person withsimilar qualifications.
• This unit must be serviced by qualified personnel only.Service by unqualified personnel may lead to electricshock or burn.
• Remote control enclosure must be mounted on verticalwall and installed in vertical position. Mounting remotecontrol enclosure in horizontal position may result incollection of liquids and lead to electric shock.
• Use only Genuine Hatco Replacement Parts whenservice is required. Failure to use Genuine HatcoReplacement Parts will void all warranties and maysubject operators of the equipment to hazardouselectrical voltage, resulting in electrical shock or burn.Genuine Hatco Replacement Parts are specified tooperate safely in the environments in which they areused. Some aftermarket or generic replacement partsdo not have the characteristics that will allow them tooperate safely in Hatco equipment.
FIRE HAzARD: Locate unit a minimum of 1″ (25 mm) fromcombustible walls and materials. If safe distances are notmaintained, discoloration or combustion could occur.
Make sure food product has been heated to the properfood-safe temperature before placing on the unit. Failureto heat food product properly may result in serious healthrisks. This unit is for holding preheated food product only.
Make sure all operators have been instructed on the safeand proper use of the unit.
This unit is not intended for use by children or personswith reduced physical, sensory, or mental capabilities.Ensure proper supervision of children and keep them awayfrom the unit.
WARNINGThis unit has no “user-serviceable” parts. If service isrequired on this unit, contact an Authorized Hatco ServiceAgent or contact the Hatco Service Department at 800-558-0607 or 414-671-6350; fax 800-690-2966; orInternational fax 414-671-3976.
BURN HAzARD: Some exterior surfaces on unit will gethot. Use caution when touching these areas.
Locate unit at proper counter height in an area that isconvenient for use. The location should be level to preventunit or its contents from falling accidentally and strongenough to support the weight of unit and contents.
Do not operate built-in models without control boxmounted properly as described in installation instructions.
Do not operate unit without installing supplied legs.
The National Sanitation Foundation (NSF) requires thatunits over 36″ (914 mm) in width or weighing more than 80 lbs. (36 kg) either be sealed to or raised aboveinstallation surface. If unit cannot be sealed at the point ofuse, 4″ (102 mm) legs are included to allow for propercleaning access below unit.
Unit is designed and recommended for use in or on metalliccountertops. Damage to any countertop material is notcovered under the Hatco warranty. For other surfaces,verify with manufacturer that material is suitable forprolonged temperatures up to 200°F (93°C).
Do not modify wiring or cut thermostat capillary wire oncontrol enclosure to increase remote mounting distance.Cutting thermostat capillary wire will cause unit to overheatand may damage unit as well as surrounding countertop.
Do not use excessive force when tightening mountingscrews on built-in units. This may damage unit and/orcountertop.
Do not lay unit on the side with the control panel. Damageto unit could occur.
Use non-abrasive cleaners and cloths only. Abrasivecleaners and cloths could scratch the finish of the unit,marring its appearance and making it susceptible to soilaccumulation.
Install remote mounted control enclosure outside of heatzone. Locating control enclosure inside heat zone willcause control(s) to overheat, malfunction, and fail.
Do not slide pans across hardcoat surface, use rough-bottomed pans, or drop anything on hardcoat surface.Scratching may occur. Damage to hardcoat surface causedby misuse is not covered under warranty.
NOTICE
CAUTION
WARNING
Read the following important safety information before using this equipment to avoidserious injury or death and to avoid damage to equipment or property.
MODEL DESCRIPTION
Form No. GRSm-07114
MODEL DESIGNATION
GRS ModelThe GRS Heated Shelf is ideal for pass-through areas, buffetlines, or as a heated work shelf. It features an Power On/Offrocker switch with indicator light, an adjustable thermostatcontrol, and a 6′ (1829 mm) power cord with plug. Surfacemounted, blanket-type foil elements distribute heat under theentire stainless steel or hardcoat aluminum surface.
all GRS models are shipped from the factory completelyassembled and ready for use.
Figure 1. GRS model
GRSB and GRSBF ModelsThe GRSB and GRSBF Built-In Heated Shelves have ahardcoat aluminum surface and a blanket-type foil element foruniform heat distribution. Ideal for server-to-customer pass-through areas, buffet/cafeteria lines, and other self-serviceareas. The GRSB model features a recessed top. The GRSBFmodel features a flat top.
a 36″ (914 mm) flexible conduit channels the power lines fromthe shelf to a control box. The control box comes with anilluminated POWER ON/OFF (I/O) rocker switch, an adjustablethermostat control, and mounting brackets. The attached controlbox can be mounted semi-remotely up to 36″ (914 mm) fromthe unit. a 6′ (1829 mm) power cord and plug is attached to thecontrol box.
The GRSB and GRSBF models have a 3/4″ (19 mm) flangededge that allows the unit to drop into a countertop opening forrecessed mounting. The shelves are easy to clean with a non-abrasive, damp cloth and/or non-abrasive cleaner. all GRSBand GRSBF models are shipped from the factory completelyassembled and ready for use.
Plug ConfigurationsUnits are supplied from the factory with an electrical cord andplug installed. Plugs are supplied according to the application.
ELECTRIC SHOCK HAzARD: Plug unit into a properlygrounded electrical receptacle of the correct voltage, size,and plug configuration. If plug and receptacle do notmatch, contact a qualified electrician to determine andinstall the proper voltage and size electrical receptacle.
Note: the specification label is located on the bottom of GRSmodels and the bottom of the remote control box onGRSB and GRSBF models. See label for serial numberand verification of unit electrical information.
WARNING
D
B
Front View Side View
A
C
E
Figure 4. Plug Configurations
Note: Receptacle not supplied by Hatco.
NEMA 5-15P NEMA 5-20P
NEMA 6-15P
CEE 7/7 Schuko BS-1363
Dimensions — GRS Models
Note: All models listed above are based on 19-1/2″ (495 mm) depth. the additional depths available include:
230–240 (CE) 1901-2070 8.3-8.6 BS-1363 64 lbs. (29 kg)
SPECIFICATIONS
INSTALLATION
Form No. GRSm-071112
GeneralUse the following procedures to install the GRS, GRSB, andGRSBF units.
FIRE HAzARD: Locate unit a minimum of 1″ (25 mm) fromcombustible walls and materials. If safe distances are notmaintained, discoloration or combustion could occur.
Locate unit at proper counter height in an area that isconvenient for use. The location should be level to preventunit or its contents from falling accidentally and strongenough to support the weight of unit and contents.
Do not operate built-in models without control boxmounted properly as described in the installationinstructions.
Do not operate unit without installing supplied legs.
The National Sanitation Foundation (NSF) requires thatunits over 36″ (914 mm) in width or weighing more than 80 lbs. (36 kg) either be sealed to or raised above theinstallation surface. If unit cannot be sealed at the point ofuse, 4″ (102 mm) legs are included to allow for propercleaning access below unit.
Do not operate unit prior to installing legs. Damage to unitcould occur.
CAUTION
WARNING
NOTICE
GRS Models1. Remove the unit from the carton and place it upside down
on the cardboard.
Note: to prevent delay in obtaining warranty coverage,complete online warranty registration. See theImPORTaNT OWNER INFORmaTION section fordetails.
2. Install the 1″ (25 mm) legs to theunit.
a. Thread a foot stud into thehole at each corner on thebottom of the unit. Tightensecurely, but do not over-tighten.
b. Slip a rubber foot over eachfoot stud.
Note: If 4″ (102 mm) legs arerequired, refer to the OPTIONS aND aCCESSORIESsection in this manual for installation instructions.
3. Turn unit upright, and place unit in the desired location.
• Locate the unit in an area where the ambient airtemperature is constant and a minimum of 70° F (21° C).avoid areas that may be subject to active air movementsor currents (i.e., near exterior doors, exhaust fans/hoods,air conditioning ducts, etc...).
• make sure the unit is at the proper counter height in anarea convenient for use.
• make sure the countertop is level and strong enough tosupport the weight of the unit and food product.
• make sure all the feet on the bottom of the unit arepositioned securely on the countertop.
FootStud
RubberFoot
Electrical Rating Chart — Standard GRSBF Models
The shaded areas contain electrical information for International models only.
INSTALLATION
Form No. GRSm-0711 13
GRSB and GRSBF Models1. Remove the unit from the carton and place it upside down
on the cardboard.
Note: to prevent delay in obtaining warranty coverage,complete online warranty registration. See theImPORTaNT OWNER INFORmaTION section fordetails.
Figure 8. Underside of GRSB models
2. Remove and save the bracket screws from the undersideof the unit.
Note: the control box may be moved to the most convenientlocation on the underside of the unit. For semi-remoteinstallations, leave the control box in place until the unitis placed into the countertop.
Unit is designed and recommended for use in or onmetallic countertops. Damage to any countertop materialis not covered under the Hatco warranty. For othersurfaces, verify with manufacturer that material is suitablefor prolonged temperatures up to 200°F (93°C).
3. Prepare countertop opening. Refer to the appropriate“Countertop Cutout” chart on the following pages forrecommended countertop cutout dimensions.
4. apply a bead of NSF-approved sealant between thecountertop material and the mounting flange on the unit.The sealant must be rated for use at a minimumtemperature of 250°F (121°C).
5. Place the unit into the countertop opening.
6. assemble the Z-brackets to the underside of the unit usingthe four bracket screws removed earlier in this procedure.
Note: Units 48″ (1219 mm) or longer require two additional Z-brackets to be installed midway along the front and rearof the unit.
7. adjust the mounting screws on the Z-brackets until the topflange lies flat on the countertop.
Do not use excessive force when tightening mountingscrews on built-in units. This may damage unit and/orcountertop.
Bracket Screw
NOTICE
NOTICE
8. Remove any excess sealant.
9. If desired or necessary, the control box can be mounted ina semi-remote location.
a. Remove the control box from the bottom of the unit.
b. If necessary, remove the end brackets from the controlbox, rotate/reposition, and re-secure to the control box.
c. The control box can be panel, surface, under counter, orrecess mounted.
Figure 9. Control Box mounting Options
d. The distance the control box can be mounted from theunit is determined by the 36″ (914 mm) conduit. Do notpull the conduit tight to increase the mounting distance.The conduit should have some slack after the control boxis mounted.
Do not modify wiring or cut thermostat capillary wire oncontrol enclosure to increase-remote mounting distance.Cutting thermostat capillary wire will cause unit to overheatand may damage unit as well as surrounding countertop.
10. Once all components are secured, proceed to theOPERaTION section.
Note: A 6′ (1829 mm) cord is supplied with this unit; anyexcess cord should be routed neatly so it does not hangdown.
Panel
Under Counter
Surface
7-1/4″(184 mm)
2″(51 mm)2-1/8″
(54 mm)
7″(178 mm)
NOTICE
INSTALLATION
Form No. GRSm-071114
Bracket Screw
MetallicCountertop
Mounting Screw
Z-Bracket
Apply a bead of NSF-approved sealant between thecountertop and the mounting flange on the unit. Sealant must be rated for use at a minimum temperature of 250° F (121° C).
Figure 10. GRSB model Installation
Countertop Cutout — GRSB Models
Model Minimum Width Maximum Width Minimum Depth Maximum Depth
GeneralUse the following procedure to turn on and operate the GRS,GRSB, and GRSBF units.
Read all safety messages in the IMPORTANT SAFETyINFORMATION section before operating this equipment.
1. Plug unit into a properly grounded electrical receptacle ofthe correct voltage, size, and plug configuration. Refer tothe SPECIFICaTIONS section in this manual for details.
2. move the Power On/Off (I/O) switch to the On (I) position.
BURN HAzARD: Some exterior surfaces on unit will gethot. Use caution when touching these areas.
3. Turn the thermostat control to the desired temperaturesetting.
Note: turning the thermostat control knob clockwise willincrease the temperature setting. turning thethermostat control knob counterclockwise will decreasethe temperature setting.
4. allow the unit 30 minutes to reach operating temperature.
Note: Refer to the OPTIONS aND aCCESSORIES sectionfor installation and operation information for GRSB andGRSBF units equipped with a flush-style remotemounted control enclosure.
WARNING
CAUTION
ThermostatControl
Power On/OffSwitch
Figure 12. Control Panel — GRS model
ThermostatControl
POWER ON/OFF (I/O)Switch
Figure 13. Control Panel — GRSB and GRSBF models
OPERATION
MAINTENANCE
GeneralHatco Glo-Ray Heated Shelf units are designed for maximumdurability and performance with minimum maintenance.
ELECTRIC SHOCK HAzARD:• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any cleaning,adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is notwaterproof. Do not operate if unit has been submergedor saturated with water.
• This unit is not “jet-proof” construction. Do not use jet-clean spray to clean this unit.
• Do not steam clean or use excessive water on unit.
• Use only Genuine Hatco Replacement Parts whenservice is required. Failure to use Genuine HatcoReplacement Parts will void all warranties and maysubject operators of the equipment to hazardouselectrical voltage, resulting in electrical shock or burn.Genuine Hatco Replacement Parts are specified tooperate safely in the environments in which they areused. Some aftermarket or generic replacement partsdo not have the characteristics that will allow them tooperate safely in Hatco equipment.
WARNING
This unit has no “user-serviceable” parts. If service isrequired on this unit, contact an Authorized Hatco ServiceAgent or contact the Hatco Service Department at 800-558-0607 or 414-671-6350; fax 800-690-2966; orInternational fax 414-671-3976.
CleaningTo preserve the finish of the Glo-Ray Heated Shelf, it isrecommended that all surfaces be cleaned daily
Use non-abrasive cleaners and cloths only. Abrasivecleaners and cloths could scratch the finish of the unit,marring its appearance and making it susceptible to soilaccumulation.
1. Turn off the unit, unplug the power cord, and allow the unitto cool.
2. Remove and wash all food pans, if necessary.
3. Wipe down all metal surfaces with a non-abrasive, dampcloth. Stubborn stains may be removed with a good stainlesssteel or non-abrasive cleaner. Clean hard to reach areasusing a small brush and mild soap.
4. Wipe dry all surfaces using a non-abrasive, dry cloth.
NOTICE
WARNING
Form No. GRSm-0711 17
TROUBLESHOOTING GUIDE
OPTIONS AND ACCESSORIES
Symptom Probable Cause Corrective Action
Unit too hot. Thermostat control set too high. adjust thermostat control to a lower setting.
Thermostat control stuck in the “on”position.
Contact authorized Service agent or Hatco forassistance.
Unit plugged into an incorrect power supply. Verify with qualified personnel that powersupply matches unit specification.
Unit not hot enough. Thermostat control set too low. adjust thermostat control to a higher setting.
Location of unit is susceptible to aircurrents (air conditioning ducts or exhaustfans).
Block air currents or relocate unit.
Unit not working at all. Unit not plugged in. Plug unit into proper power supply.
Unit not turned on. move Power On/Off (I/O) switch to the On (I)position.
Power On/Off (I/O) switch is notfunctioning.
Contact authorized Service agent or Hatco forassistance.
Heating element is burned out. Contact authorized Service agent or Hatco forassistance.
Thermostat control is defective. Contact authorized Service agent or Hatco forassistance.
This unit must be serviced by qualified personnel only.Service by unqualified personnel may lead to electricshock or burn.
WARNINGELECTRIC SHOCK HAzARD: Turn OFF power switch,unplug power cord, and allow unit to cool beforeperforming any cleaning, adjustments, or maintenance.
WARNING
4″ (102 mm) Adjustable Legs (GRS Models)Use the following procedure to install 4″ adjustable legs on aGRS model.
Note: 4″ (102 mm) legs are standard on models 42″ (1067 mm) and wider.
1. Turn off the unit, unplug the power cord, and allow the unitto cool.
Do not lay unit on the side with the control panel. Damageto unit could occur.
2. Carefully turn the unit upside down and lay the unit on a flatsurface. make sure to cover the surface with something toprevent scratching the unit.
3. at each corner, thread a 4″ leg into the bottom of the unit.Hand-tighten until snug. Do not over-tighten.
4. Return the unit to the upright position.
NOTICE
Figure 14. Leg Installation
Note: the feet on the 4″ legs are adjustable for leveling theunit. Use a 9/16″ (14 mm) open-end wrench to makeleveling adjustments once the unit is placed in its finalposition.
4″ (102 mm)Leg
Lengthen
Shorten
Adjustable Foot
OPTIONS AND ACCESSORIES
Form No. GRSm-071118
Remote Mounted Control Enclosures(GRSB and GRSBF models)Two flush-style remote mounted control enclosures areavailable for the GRSB and GRSBF units — the mechanicalThermostat Control enclosure and the digital IndicatingTemperature Control (ITC) enclosure. Both control enclosuresare installed using the following procedure.
ELECTRIC SHOCK HAzARD: Remote control enclosuremust be mounted on vertical wall and installed in verticalposition. Mounting remote control enclosure in horizontalposition may result in collection of liquids and lead toelectric shock.
Install remote mounted control enclosure outside of the heatzone. Locating the control enclosure inside the heat zonewill cause the control(s) to overheat, malfunction, and fail.
Do not modify wiring or cut thermostat capillary wire oncontrol enclosure to increase semi-remote mountingdistance. Cutting thermostat capillary wire will cause unit tooverheat and may damage unit as well as surroundingcountertop.
Note: A qualified electrician is recommended for connectingthe units to a power source.
1. Prepare cutout and pre-drill screw holes (see illustrationbelow for dimensions).
2. Remove trim cover from control enclosure.
3. Position control enclosure into opening through thebackside.
4. Secure control enclosure to surface using screws (not supplied).
5. Connect proper power source to the mounted remotecontrol enclosure.
6. Reinstall the trim cover. Seal the trim cover to the mountingsurface with silicone adhesive
Note: Units are equipped with a 36″ (914 mm) flexible conduitconnecting the control enclosure to the unit.
WARNING
NOTICE
Power On/Off SwitchBoth flush-style remote mounted control enclosures areequipped with a Power ON/OFF (I/O) switch. move the PowerON/OFF (I/O) switch to the ON position to turn on the unit. Theindicator light in the switch glows when the unit is on.
Adjusting the Thermostat ControlTurn the thermostat control clockwise to increase thetemperature setpoint. Turn the thermostat controlcounterclockwise to decrease the temperature setpoint.
Figure 16. Thermostat Control Enclosure
HATCO CORP. MILWAUKEE, WI U.S.A.
OFF ON
1
2
3
4
56
7
8
9
10
ThermostatControl
Power ON/OFF Switch
Figure 15. Remote mounted Control Enclosure Installation Dimensions
Thermostat Enclosure4″ (102 mm)
ITC Enclosure4-3/4″ (121 mm)
Mounting SurfaceTrim Cover
Control Enclosure
5-7/8″(149 mm)
3-7/8″(98 mm)
6-3/8″(162 mm)
6-7/8″(174 mm)
Side View of Installed EnclosureFront View of Cutout
IMPORTANT NOTE:
make sure the installationlocation provides enoughroom for electricalconnections to the controlenclosure.
OPTIONS AND ACCESSORIES
LIMITED WARRANTy
Form No. GRSm-0711 19
Adjusting/Programming the ITCUnits equipped with the ITC enclosure will heat up to thesetpoint temperature automatically when they are turned on.Use the following procedure to program the setpointtemperature.
Note: the temperature shown on the display may beinaccurate when unit temperature is below 130°F(54°C).
If the programming sequence is interrupted before completingthe last step, the changed values will not be accepted intomemory.
1. Press the SET key once to view temperature setpoint (SP)on the display.
2. Press the SET key again to view the current setpoint value.
3. Press the Up or Down arrow key to select the desiredsetpoint value. Pressing and holding either of the arrowkeys will advance the setpoint change rapidly.
4. Press the SET key to complete the programmingsequence and enter the value into memory. The displaywill go blank for two seconds to acknowledge the end ofthe programming sequence and acceptance of the newtemperature value.
Note: After ten seconds of inactivity during the programmingprocess, the controller will automatically exitprogramming mode and revert back to the originaltemperature value without accepting the new value.
Figure 17. Indicating Temperature Control (ITC) Enclosure
HATCO CORP. MILWAUKEE, WI U.S.A.
OFF ON
SET
TEMPERATURE
SET KeyUp Arrow
Key
DownArrowKey
Display
1. PRODUCT WARRANTy
Hatco warrants the products that it manufactures (the “Products”) to be
free from defects in materials and workmanship, under normal use and
service, for a period of one (1) year from the date of purchase when
installed and maintained in accordance with Hatco’s written instructions
or 18 months from the date of shipment from Hatco. Buyer must
establish the Product’s purchase date by registering the Product with
Hatco or by other means satisfactory to Hatco in its sole discretion.
Hatco warrants the following Product components to be free from
defects in materials and workmanship from the date of purchase
(subject to the foregoing conditions) for the period(s) of time and on
the conditions listed below:
a) One (1) year Parts and Labor PLUS One (1) Additionalyear Parts-Only Warranty:Conveyor Toaster Elements (metal sheathed)
Drawer Warmer Elements (metal sheathed)
Drawer Warmer Drawer Rollers and Slides
Strip Heater Elements (metal sheathed)
Display Warmer Elements (metal sheathed air heating)
Holding Cabinet Elements (metal sheathed air heating)
Heated Well Elements — HWB Series (metal sheathed)
b) One (1) year Parts and Labor PLUS Four (4) years Parts-Only Warranty on pro-rated terms that Hatco will explain at Buyer’s request:3CS and FR Tanks
c) One (1) year Parts and Labor PLUS Nine (9) years Parts-Only Warranty on:Electric Booster Heater Tanks
Gas Booster Heater Tanks
d) Ninety (90) Day Parts-Only Warranty: Replacement Parts
THE FOREGOING WaRRaNTIES aRE EXCLUSIVE aND IN LIEU OF
aNY OTHER WaRRaNTY, EXPRESSED OR ImPLIED, INCLUDING
BUT NOT LImITED TO aNY ImPLIED WaRRaNTY OF
mERCHaNTaBILITY OR FITNESS FOR a PaRTICULaR PURPOSE
OR PaTENT OR OTHER INTELLECTUaL PROPERTY RIGHT
INFRINGEmENT. Without limiting the generality of the foregoing, SUCH
WaRRaNTIES DO NOT COVER: Coated incandescent light bulbs,
