GRUNDFOS DATA BOOKLET
SP9-23 Rp2 6"3X380-415/50 5.5kW Grundfos Pump 98699066
Thank you for your interest in our productsPlease contact us for more information, or visit our websitehttps://www.lenntech.com/grundfos/SPFAM/98699066/SP-9-23.html
[email protected]. +31-15-261.09.00fax. +31-15-261.62.89
BE > THINK > INNOVATE
Printed from Grundfos Product Centre [2018.02.043]
Position Qty. Description1 SP 9-23
Product No.: 98699066
Submersible borehole pump, suitable for pumping clean water. Can be installed vertically orhorizontally. All steel components are made in stainless steel, EN 1.4301 (AISI 304), that ensures highcorrosive resistance. This pump carries drinking water approval.The pump is fitted with a 5.5 kW MS6000 motor with sand shield, mechanical shaft seal,water-lubricated journal bearings and a volume compensating diaphragm. The motor is a canned typesubmersible motor offering good mechanical stability and high efficiency. Suitable for temperatures upto 40 °C.The motor is fitted with the Grundfos Tempcon sensor that, by use of powerline communicationtogether with a MP204 control panel, enables temperature monitoring.The motor is for direct-on-line starting (DOL).
Further product detailsThe pump is suitable for applications similar to the following:
- raw-water supply- irrigation- groundwater lowering- pressure boosting- fountain applications.
The Grundfos SP pump is renowned for its high efficiency and already complies with the requirementsof the Minimum Efficiency Index, and therefore Grundfos is amongst the best in class withinsubmersible pumps.
PumpAll pump surfaces that are in contact with pumped liquids are made in stainless steel which makesthem corrosion- and wear-resistant. The corrosion diagram below shows the capabilities of the pumpand motor in relation to the temperature in Celsius (y-axis) and the concentration of chloride in ppm(x-axis).
The elastomer parts in the pump offer good wear resistance and long service intervals. The bearingsare made of LSR (Liquid Silicone Rubber), sealing rings are made of TPU (ThermoplasticPoly-Urethane) and the non-return valve is made of NBR (Nitrile-Butadiene Rubber). The specialelastomer material of the bearings offers increased resistance to sand and other abrasive particles(from 50 to 150 mg/l).
In case the pump is used for pumping water with high content of hydrocarbons or solvents, Grundfosoffers FKM rubber parts (Fluorocarbon) which are oil and temperature-resistant up to 90 °C.
Printed from Grundfos Product Centre [2018.02.043]
The pump is built with octagonal bearings with sand flush channels that minimise wear. As wear of the pump isinevitable, the pump design allows for easy replacement of all internal wear parts (bearings, impeller, wear rings andseal rings) to maintain high performance and a long lifetime.
The suction interconnector is fitted with a strainer to prevent large particles from entering the pump. Thesuction interconnector is designed to comply with NEMA standards for motor mounting/dimensions.
MotorThe stator is hermetically encapsulated in stainless steel and the windings are embedded in polymercompound. This results in high mechanical stability, optimum cooling and reduces the risk of shortcircuits in the windings.The shaft seal faces are ceramic/carbon. The material combination provides good dry-runningresistance. Together with the shaft seal housing, the sand shield forms a labyrinth seal, which duringnormal operating conditions prevents penetration of sand particles into the shaft seal.The motor is fitted with the Grundfos Tempcon temperature sensor device that includes a NTC-resistorwhich senses the temperature. The resistor is built-in close to the winding. The temperature isconverted into a high-frequency signal which is sent via the submersible drop cable and which can beconverted into a temperature reading by means of Grundfos MP204.The MP204 is an electronic motor protection device that also monitors the supply network quality toprotect the submersible motor against supply network disturbances.
Liquid:Pumped liquid: WaterMaximum liquid temperature: 40 °CMax liquid t at 0.15 m/sec: 40 °CLiquid temperature during operation: 20 °CDensity: 998.2 kg/m³
Technical:Speed for pump data: 2900 rpmRated flow: 9 m³/hRated head: 121.4 mShaft seal for motor: CER/CARNBRApprovals on nameplate: CE,GOST2Curve tolerance: ISO9906:2012 3BMotor version: T40
Materials:Pump: Stainless steel
EN 1.4301AISI 304
Impeller: Stainless steelEN 1.4301AISI 304
Motor: Stainless steelDIN W.-Nr. 1.4301AISI 304
Installation:Pump outlet: RP2Motor diameter: 6 inch
Electrical data:Motor type: MS6000Rated power - P2: 5.5 kW
Printed from Grundfos Product Centre [2018.02.043]
Position Qty. DescriptionPower (P2) required by pump: 5.5 kWMains frequency: 50 HzRated voltage: 3 x 380-400-415 VRated current: 13.6-13.4-13.6 AStarting current: 470-510-520 %Cos phi - power factor: 0.82-0.78-0.75Rated speed: 2870-2880-2890 rpmStart. method: direct-on-lineEnclosure class (IEC 34-5): IP68Insulation class (IEC 85): FBuilt-in temp. transmitter: yes
Others:Minimum efficiency index, MEI ≥: 0.70ErP status: EuP Standalone/Prod.Net weight: 55 kgGross weight: 89.2 kgShipping volume: 0.264 m³
Printed from Grundfos Product Centre [2018.02.043]
98699066 SP 9-23 50 HzH
[m]
0
20
40
60
80
100
120
140
160
Q [m³/h]0 1 2 3 4 5 6 7 8 9 10 11
eta[%]
0
20
40
60
80
100
SP 9-23, 3*400 V, 50Hz
P[kW]
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
P1
P2
Printed from Grundfos Product Centre [2018.02.043]
H[m]
0
20
40
60
80
100
120
140
160
Q [m³/h]0 2 4 6 8 10
eta[%]
0
20
40
60
80
100
SP 9-23, 3*400 V, 50Hz
P[kW]
0
1
2
3
4
5
6 P1
P2
139.5
547
1451
1998
139.5RP2
GN
DOLY
U1, W2
V1, U2
W1, V2
Brown
Grey
Black
M
L1 L2 L3 PE
W2
W1U1 V1
U2 V2
PE
3M
L1 L2 L3 PE
U1 V1 W1
3
PE
Description ValueGeneral information:Product name: SP 9-23Product No: 98699066EAN number: 5712600106154Technical:Speed for pump data: 2900 rpmRated flow: 9 m³/hRated head: 121.4 mStages: 23Impeller reduc.: NONEShaft seal for motor: CER/CARNBRApprovals on nameplate: CE,GOST2Curve tolerance: ISO9906:2012 3BModel: AValve: YESMotor version: T40Materials:Pump: Stainless steel
EN 1.4301AISI 304
Impeller: Stainless steelEN 1.4301AISI 304
Motor: Stainless steelDIN W.-Nr. 1.4301AISI 304
Installation:Pump outlet: RP2Motor diameter: 6 inchLiquid:Pumped liquid: WaterMaximum liquid temperature: 40 °CMax liquid t at 0.15 m/sec: 40 °CLiquid temperature during operation: 20 °CDensity: 998.2 kg/m³Electrical data:Motor type: MS6000Applic. motor: NEMARated power - P2: 5.5 kWPower (P2) required by pump: 5.5 kWMains frequency: 50 HzRated voltage: 3 x 380-400-415 VRated current: 13.6-13.4-13.6 AStarting current: 470-510-520 %Cos phi - power factor: 0.82-0.78-0.75Rated speed: 2870-2880-2890 rpmStart. method: direct-on-lineEnclosure class (IEC 34-5): IP68Insulation class (IEC 85): FMotor protec: NONEThermal protec: externalBuilt-in temp. transmitter: yesMotor No: 78195511Others:Minimum efficiency index, MEI ≥: 0.70ErP status: EuP Standalone/Prod.Net weight: 55 kgGross weight: 89.2 kgShipping volume: 0.264 m³
139.5
139.5
RP2
GN
Printed from Grundfos Product Centre [2018.02.043]
98699066 SP 9-23 50 Hzcos phi
eta
0.0
0.2
0.4
0.6
0.8
P2 [kW]0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0
I[A]
0
4
8
12
16
SP9-23 + MS6000 5.5 kW 3*400 V, 50 Hz
eta
cos phi
I
n[rpm]
2000
2200
2400
2600
2800
P1[kW]
0
4
8
12
16n
P1
Printed from Grundfos Product Centre [2018.02.043]
98699066 SP 9-23 50 Hz
Note! All units are in [mm] unless others are stated.Disclaimer: This simplified dimensional drawing does not show all details.
139.5
547
1451
1998
139.5RP2
GN
Printed from Grundfos Product Centre [2018.02.043]
98699066 SP 9-23 50 Hz
Note! All units are in [mm] unless others are stated.
DOLY
U1, W2
V1, U2
W1, V2
Brown
Grey
Black
M
L1 L2 L3 PE
W2
W1U1 V1
U2 V2
PE
3M
L1 L2 L3 PE
U1 V1 W1
3
PE
Disclaimer: The information about the Grundfos pump in this document may be outdated.Data may be subject to alterations without further notice.Please contact us to verify the data above is still accurate/up-to-date.
All information is copyright Grundfos.
[email protected]. +31-15-261.09.00fax. +31-15-261.62.89
