1+1.562.906.9300 | www.agsecorp.com | sales@agsecorp.com

GSE & TOOLING

OEM-APPROVED FOR CFM56 ENGINES

Shipping Stand for CFM56-7B Engines (used on Boeing 737NG Aircraft)

AGSE P/Ns: AM-2811-4800 (Shipping Cradle) & AM-2563-200/-227 (Transportation Base)

Shipping Stand for CFM56-5A/-5B Engines (used on Airbus A320 Family Aircraft)AGSE P/Ns: AM-2718 (Shipping Cradle) & AM-2563 (Transportation Base)

Low Pressure Turbine & Shaft Major Module 3 Shipping Container

(with cover removed)

AGSE P/N: AGSE-C049

Pedestal with Optional MountAGSE P/N: AGSE-T016

Pneumatic Tire DollyAGSE P/N: AM-1686

For decades, AGSE has been a global leader in the original design, development, and manufacture of qualified & recommended solutions for the handling of CFM56 engines:

Approved by CFM International, GE Aviation, or Safran Aircraft Engines!

• Shipping Stands• Engine Covers• Lifting Fixtures• Site Transport• Pedestals

• Shipping Containers

• Line, Hangar & Shop Maintenance Tooling

2+1.562.906.9300 | www.agsecorp.com | sales@agsecorp.com

Approved, qualified, and recommended by CFM International, GE Aviation, or Safran Aircraft Engines for the handling of CFM56-3, CFM56-5 & CFM56-7 engines (unless denoted with a † ).

*AGSE Shipping Stands are designed and built in compliance with the specifications and requirements of the engine’s original equipment manufacturer (OEM). The customer is solely responsible for selecting the appropriate packaging based upon all information at his/her disposal, including the specific application, regulatory compliances, product compatibility, shipping requirements, and documentation issued by the Engine OEM. Any AGSE-referenced shipping information presented either in this product literature or other AGSE documentation is intended as general guidance only and should not be considered a complete set of shipping requirements that can alter, satisfy, or influence both regulatory and Engine OEM shipping requirements. The content found in AGSE marketing materials and other documentation is subject to change; AGSE accepts no liability for loss or damage resulting from changes, errors, omissions, or misinterpretations of these AGSE publications.

OEM-APPROVED FOR CFM56 ENGINES SHIPPING STANDS

• Air/Truck transport or storage for engine in QEC configuration (ready for installation)*

• Bootstrap capable (with AGSE or alternate lifting devices) to support engine during removal/installation from/to select aircraft

Our trusted & reliable transportation and storage solutions not only offer low total cost of ownership, but an extensive range of applications that can

benefit any airline, aircraft hangar, or engine shop operation:

• Tie-Down rings on Transportation Base offer secure retainment for both engine & Shipping Stand

• Shock-Absorbing mounts cushion vibrations during transport

SHIPPING STANDS BY PART NUMBER

PART NUMBER: AGSE CFM56 ENGINE(S)ACCOMMODATED

AIRCRAFT APPLICATION(S)

LOW PROFILE TO ENABLE HEIGHT-RESTRICTED

AIR SHIPMENT

CRADLE COLLAPSES TO REDUCE SHIPPING/

STORAGE VOLUME

OPTIONAL TRUCK SHIPPING MOUNTS

AVAILABLE

COMPATIBLE WITH OTHER AGSE EQUIPMENT: ACCOMMODATES OTHER SELECT

ENGINESLIFTING FIXTURES SITE TRANSPORT

AM-2811-4800 (Shipping Cradle) AM-2563-200/-227 (Transportation Base)

CFM56-7B Boeing 737NG

AGSE-V094-G01 (Low-Profile Shop Dolly)AM-1686 (Pneumatic Tire Dolly)AM-1961-111† (Cradle Caster Kit)

AGSE-E207-G01† CFM56-7B Boeing 737NG

AM-2718 (Shipping Cradle) AM-2563 (Transportation Base)

CFM56-5A/-5B Airbus A320 Family AGSE-L006† (Engine Sling)

AGSE-V094-G01† (Low-Profile Shop Dolly)AM-1686 (Pneumatic Tire Dolly)AM-1961-400† (Cradle Caster Kit)

AGSE-E208-G01† (Shipping Cradle)AM-2563 (Transportation Base)

CFM56-5A/-5B Airbus A320 Family

AGSE-E043† (Shipping Cradle)AM-2510R88† (Transportation Base)

CFM56-5A/-5B Airbus A320 Family PW2000

AM-2387 (Shipping Cradle)AM-2563 (Transportation Base)

CFM56-5C Airbus A340-200/-300

AGSE-V094-G01† (Low-Profile Shop Dolly)AM-1686 (Pneumatic Tire Dolly)

AM-1802 (Shipping Cradle)AM-2563 (Transportation Base)

CFM56-3 Boeing 737 Classic

AGSE-L012-G01† (Engine Sling)AM-1916† (Bootstrap Hoist Beam)

AGSE-V094-G01† (Low-Profile Shop Dolly)AM-1686 (Pneumatic Tire Dolly)AM-1961-100†/-111† (Cradle Caster Kit)

AGSE-E206-G01† CFM56-3 Boeing 737 Classic

= Available Feature

3+1.562.906.9300 | www.agsecorp.com | sales@agsecorp.com

RAIL MOUNTED CRADLES Bootstrap capable and compatible with other AGSE or third party Transportation Bases!

PART NUMBER: Stanley CFM56 ENGINE(S)ACCOMMODATED

AIRCRAFT APPLICATION(S) COMPATIBLE WITH TRANSPORTATION BASES CONTAINING RAIL SPACING OF:

111502-1† CFM56-5A/-5B Airbus A320 Family 88" 224 cm

111502-90† CFM56-5A/-5B Airbus A320 Family 90" 229 cm

111602-1† CFM56-5C Airbus A340-200/-300 88" 224 cm

111602-2† CFM56-5C Airbus A340-200/-300 90" 229 cm (shock mounted)

111602-90† CFM56-5C Airbus A340-200/-300 90" 229 cm (not shock mounted)

Approved, qualified, and recommended by CFM International, GE Aviation, or Safran Aircraft Engines for the handling of CFM56-3, CFM56-5 & CFM56-7 engines (unless denoted with a † ).

OEM-APPROVED FOR CFM56 ENGINES RAIL MOUNTED CRADLES,

ENGINE COVERS & SITE TRANSPORT

= Available Feature

SITE TRANSPORTExceptional mobility for engines during transport within a facility or between local sites as well as sturdy, convenient alignment for engine inlets during separation and mate procedures!

PART NUMBER: AGSE DESCRIPTION CFM56 ENGINE(S)ACCOMMODATED

AIRCRAFT APPLICATION(S)

COMPATIBLE WITH OTHER AGSE EQUIPMENT

MANUALLY-ADJUSTABLE HEIGHT FOR ALIGNMENT WITH

AIRCRAFT WINGSOTHER ENGINES

ACCOMMODATED

AM-1686 Pneumatic Tire Dolly

CFM56-7B Boeing 737NG AM-2811 (Shipping Cradle)

CFM56-5A/-5B Airbus A320 Family AM-2718 (Shipping Cradle)

CFM56-5C Airbus A340-200/-300 AM-2387 (Shipping Cradle)

CFM56-3 Boeing 737 Classic AM-1802 (Shipping Cradle)

AGSE-V094-G01† Low-Profile Shop Dolly

CFM56-7B Boeing 737NG

AM-2563 (Transportation Base) CFM56-5A/-5B Airbus A320 Family

CFM56-5C Airbus A340-200/-300

CFM56-3 Boeing 737 Classic

AGSE-E058† Light Weight Breakdown Stand CFM56-7B Boeing 737NG

AGSE-E016-G01 Light Weight Breakdown Stand CFM56-3 Boeing 737 Classic

AM-1961-111† Cradle Caster KitCFM56-7B Boeing 737NG AM-2811-4800 (Shipping Cradle)

CFM56-3 Boeing 737 Classic AM-1802 (Shipping Cradle)

AM-1961-400† Cradle Caster Kit CFM56-5A/-5B Airbus A320 Family AM-2718-A1 (Shipping Cradle)

AM-1961-100† Cradle Caster Kit CFM56-3 Boeing 737 Classic AM-1802 (Shipping Cradle)

AGSE-T073-G03† Inlet Cowl DollyCFM56-7B Boeing 737NG

CFM56-3 Boeing 737 Classic

AGSE-T073-G02† Inlet Cowl Dolly CFM56-7B Boeing 737NG

AGSE-E092-G01† Inlet Cowl Dolly CFM56-7B Boeing 737NG

AM-2302N-100† Inlet Cowl Dolly CFM56-5C Airbus A340-200/-300 Trent 500, Trent 700

ENGINE COVERSDependable and lasting protection against dirt, water, and contamination during engine shipment or storage!

PART NUMBER: Engine OEM CFM56 ENGINE(S)ACCOMMODATED

AIRCRAFT APPLICATION(S)

SHIPPING COVER TYPE(S):

BARE ENGINE QEC ENGINE REINFORCED WITH FITTED BAR

856A3700 CFM56-7B Boeing 737NG

856A2930 CFM56-5B Airbus A320 Family

856A2782 CFM56-5A Airbus A319 & A320

856A2330 CFM56-5C Airbus A340-200/-300

856A3505 CFM56-3 Boeing 737 Classic

856A3595 CFM56-3 Boeing 737 Classic

4+1.562.906.9300 | www.agsecorp.com | sales@agsecorp.com

Approved, qualified, and recommended by CFM International, GE Aviation, or Safran Aircraft Engines for the handling of CFM56-3, CFM56-5 & CFM56-7 engines (unless denoted with a † ).

= Available Feature

OEM-APPROVED FOR CFM56 ENGINES LIFTING FIXTURES & PEDESTALS

LIFTING FIXTURESStable and versatile overhead support for engines during horizontal build-up or transfer to/from Shipping Stands!

PART NUMBER: AGSE DESCRIPTION CFM56 ENGINE(S)ACCOMMODATED

AIRCRAFT APPLICATION(S)

MAX PROOF LOAD CAPACITY

COMPATIBLE WITH AGSE SHIPPING CRADLES

CENTER OF GRAVITY ADJUSTMENT FEATURE

OPTIONAL CONTAINER AVAILABLE

ACCOMMODATES OTHER SELECT ENGINES

AM-2106 Engine Sling

CFM56-7B Boeing 737NG 13,600 lbs 6,169 kg

Hand Crank CF6, PW2000, PW4000, RB211

CFM56-5A Airbus A319, A320 13,800 lbs 6,260 kg

CFM56-5B Airbus A320 Family 14,000 lbs 6,350 kg

CFM56-5C A340-200/-300 15,000 lbs 6,804 kg

CFM56-3 Boeing 737 Classic 11,500 lbs 5,216 kg

AGSE-L006† Engine Sling CFM56-5A/-5B Airbus A320 Family 36,000 lbs 16,329 kg AM-2718 Lifting Shackle CF6

AGSE-L012-G01† Engine Sling CFM56-3 Boeing 737 Classic 32,000 lbs 14,515 kg AM-1802 Lifting Shackle CF6, RB211

AGSE-L002† Engine Sling CFM56-3 Boeing 737 Classic 24,000 lbs 10,886 kg

Cable Sling Hook Point

CF6, PW2000, PW4000

AM-1949 Engine Sling CFM56-3 Boeing 737 Classic 20,000 lbs 9,072 kg Lifting Shackle

AM-1916† Bootstrap Hoist Beam CFM56-3 Boeing 737 Classic 14,000 lbs

6,350 kg AM-1802 1

PEDESTAL SETSAnother ideal long-term storage or horizontal engine build-up solution, achieving ergonomically-efficient centerline heights for improved productivity!

PART NUMBER: Engine OEMAGSE

CFM56 ENGINE(S)ACCOMMODATED

AIRCRAFT APPLICATION(S)

NUMBER OF PEDESTALS

MAXIMUM PROOF LOAD CAPACITY PER PEDESTAL

ACHIEVES ENGINE CENTERLINE HEIGHT(S)

856A1312

CFM56-7B Boeing 737NG

4 6,000 lbs 2,722 kg

65.4" 166 cm

CFM56-5A/-5B Airbus A320 Family

CFM56-5C Airbus A340-200/-300

CFM56-3 Boeing 737 Classic

AGSE-T016-G022/-G073/-G09 CFM56-7B Boeing 737NG 4 7,000 lbs 3,175 kg

60" 152 cm

AGSE-T016-G03 CFM56-5A/-5B Airbus A320 Family 4 7,000 lbs 3,175 kg

69" 175 cm

AGSE-T016-G11 CFM56-5C Airbus A340-200/-300 4 7,000 lbs 3,175 kg

69" 175 cm

AGSE-T016-G06 CFM56-3 Boeing 737 Classic 4 7,000 lbs 3,175 kg

56" 142 cm

AGSE-T025-G02 CFM56-5C Airbus A340-200/-300 4 7,000 lbs 3,175 kg

58"–64" 147 cm–163 cm

AM-1953-100 CFM56-3 Boeing 737 Classic 4 6,000 lbs 2,722 kg

56" 142 cm

1Container included

2Also accommodates select CF6 engines3Universal model accommodates multiple mounting adapters

to achieve variable engine centerline height(s)

5+1.562.906.9300 | www.agsecorp.com | sales@agsecorp.com

MODULE SHIPPING CONTAINERS BY PART NUMBERPART NUMBER: AGSE ENGINE MODULE(S) SUPPORTED

IN SHIPPING CONTAINERCFM56 ENGINES(S)ACCOMMODATED

AIRCRAFT APPLICATION(S)

REMOVABLE COVER

SUPPORTING FOAM INSERTS

SHOCK MOUNTS/ISOLATION SYSTEM

AGSE-C011† (AGSE-C026) Fan Disk & Booster Major Module 1 CFM56-7B Boeing 737NG

AGSE-C012 #1 & #2 Bearing Support Module 2 CFM56-7B Boeing 737NG

AGSE-C021 Low Pressure Turbine Module 13 CFM56-7B Boeing 737NG

AGSE-C022 Low Pressure Turbine Shaft Module 14 CFM56-7B Boeing 737NG

AGSE-C023 Low Pressure Turbine Frame Module 15 CFM56-7B Boeing 737NG

AGSE-C024 Transfer Gearbox Module 16 CFM56-7B Boeing 737NG

AGSE-C025 Accessory Gearbox Module 17 CFM56-7B Boeing 737NG

AGSE-C027 Fan Blades CFM56-7B Boeing 737NG

AGSE-C028† (AGSE-C049) Low Pressure Turbine & Shaft Major Module 3 CFM56-7B Boeing 737NG

AGSE-C034 Core Module CFM56-7B Boeing 737NG

AGSE-C013 Core Module CFM56-5A Airbus A319, A320

AGSE-C049 (AM-2141) Low Pressure Turbine & Shaft Major Module 3 CFM56-5A Airbus A319, A320

AM-2132 Fan Disk & Booster Module 1 CFM56-5A Airbus A319, A320

AM-2133 #1 & #2 Bearing Support Module 2 CFM56-5A Airbus A319, A320

AM-2134 Low Pressure Turbine Major Module 13 CFM56-5A Airbus A319, A320

AM-2135 Low Pressure Turbine Shaft Module 14 CFM56-5A Airbus A319, A320

AM-2136 Low Pressure Turbine Frame Major Module 15 CFM56-5A Airbus A319, A320

AM-2137 Transfer Gearbox Module 16 CFM56-5A Airbus A319, A320

AM-2138 Accessory Gearbox Module 17 CFM56-5A Airbus A319, A320

AM-2139 Major Module 1 CFM56-5A Airbus A319, A320

AM-2140 Fan Blades CFM56-5A Airbus A319, A320

AGSE-C009 Fan Disk & Booster Module 1 CFM56-5B Airbus A320 Family

AGSE-C010 #1 & #2 Bearing Support Module 2 CFM56-5B Airbus A320 Family

AGSE-C013 Core Module CFM56-5B Airbus A320 Family

AGSE-C044 Low Pressure Turbine Module 13 CFM56-5B Airbus A320 Family

AGSE-C045 Low Pressure Turbine Shaft Module 14 CFM56-5B Airbus A320 Family

AGSE-C046 Low Pressure Turbine Frame Module 15 CFM56-5B Airbus A320 Family

AGSE-C047 Fan Disk & Booster Major Module 1 CFM56-5B Airbus A320 Family

AGSE-C048 Fan Blades CFM56-5B Airbus A320 Family

AGSE-C049 Low Pressure Turbine & Shaft Major Module 3 CFM56-5B Airbus A320 Family

AM-2137 Transfer Gearbox Module 16 CFM56-5B Airbus A320 Family

AM-2138 Accessory Gearbox Module 17 CFM56-5B Airbus A320 Family

AGSE-C049 (AM-2528) Low Pressure Turbine & Shaft Major Module 3 CFM56-5C Airbus A340-200/-300

AGSE-C050 Core Major Module CFM56-5C Airbus A340-200/-300

AM-2137 Transfer Gearbox Module 16 CFM56-5C Airbus A340-200/-300

AM-2138 Accessory Gearbox Module 17 CFM56-5C Airbus A340-200/-300

AM-2519 Booster Module 1 CFM56-5C Airbus A340-200/-300

AM-2520 #1 & #2 Bearing Support Module 2 CFM56-5C Airbus A340-200/-300

AM-2521 Low Pressure Turbine Module 13 CFM56-5C Airbus A340-200/-300

AM-2522 Low Pressure Turbine Shaft Module 14 CFM56-5C Airbus A340-200/-300

AM-2523 Low Pressure Turbine Frame Module 15 CFM56-5C Airbus A340-200/-300

AM-2526 Fan Case Major Module 1 CFM56-5C Airbus A340-200/-300

AM-2527 Fan Blades CFM56-5C Airbus A340-200/-300

AGSE-C007 Fan Booster CFM56-3 Boeing 737 Classic

AGSE-C008 #1 & #2 Bearing Support Module 2 CFM56-3 Boeing 737 Classic

AGSE-C035 Fan Disk & Booster Module 1 CFM56-3 Boeing 737 Classic

AGSE-C036 Core Module CFM56-3 Boeing 737 Classic

AGSE-C037 Low Pressure Turbine & Shaft Major Module 3 CFM56-3 Boeing 737 Classic

AGSE-C038 Low Pressure Turbine Module 13 CFM56-3 Boeing 737 Classic

AGSE-C039 Low Pressure Turbine Shaft Module 14 CFM56-3 Boeing 737 Classic

AGSE-C040 Low Pressure Turbine Frame Module 15 CFM56-3 Boeing 737 Classic

AGSE-C041 Transfer Gearbox Module 16 CFM56-3 Boeing 737 Classic

AGSE-C042 Accessory Gearbox Module 17 CFM56-3 Boeing 737 Classic

AGSE-C043 Fan Blades CFM56-3 Boeing 737 Classic

Approved, qualified, and recommended by CFM International, GE Aviation, or Safran Aircraft Engines for the handling of CFM56-3, CFM56-5 & CFM56-7 engines (unless denoted with a † ).

OEM-APPROVED FOR CFM56 ENGINE MODULES SHIPPING CONTAINERS

= Available Feature

Fully enclosed to shield all critical modules against contamination and damage during split engine transport!

6+1.513.402.7246 | www.agsecorp.com | toolingsales@agsecorp.com

LINE MAINTENANCE TOOLINGPART

NUMBER: CFM INT'L

DESCRIPTION

856A2609 Jacking Block - Fuel Pump/MEC or HMU856A2668 Puller Adapters856A2682 Eddy Current Inspection Kit - Fan Blades856A2686 Hand Cranking Drive Socket856A2691 Removal Tool - Spacer Pliers856A2953 Guide Pins - Stator Alternator 856A2956 Assistance Tool - Ring Fan Assembly

856A2957 Tool Set - Assembly/Disassembly Lubrication Unit Scavenge Filter Housing

856A2958 Actuation Hose Assembly - VSV 856A2961 Installation/Removal Tool - AGB Oil & Magnetic Seal856A3074 Balance Weights Riveter - Booster856A3519 Three (3) Legs Handling Sling - AGB856A3525 Removal/Installation Cradle - AGB 856A3557 D-Seal Tool - Magnetic Plug Lube Unit856A3576 Removal/Installation Tool - AGB Seals (7B27A) 856A3583 Leak Test Oil Seals

856A3598 Removal/Installation Cradle - Fuel Pump & MEC Package

856A3604P01 Wrench - Horizontal Drive Shaft Nut 856A3617 Pusher/Puller - Lube Unit Magnetic Plug856A3708 Pusher/Puller - Radial Drive Shaft856A3709 Alignment Fixture - AGB856A3726 Protective Floor - Fan Inlet Case856A3728 Core Engine Sealing Plate & Lock856A3770P03 Fan Blade Plotting Software856A3771 Check Template - Fan Blade Leading Edge856A3778 Guide Pins - Rear Spinner856A3779 Platform Puller - Fan Blade856A3782 Removal Wrench - Fan Blade Retainer Ring856A4624 Scouring Fixture - Fan Case Abradable Strip856A4628 Blade Template (Inches)856A4637 Inspection Tool - Booster Spool Forward Flange856A4640 Inspection Tool - Fan Disk Lugs856A4646 Gauge - Fan Blade Rear Shank856A5564P01 Resurfacing Kit - Spherical End Tube Coupling856A5807 Spiral Stencil - Front ConeFAN & BOOSTER MODULE TOOLING856A2316 Torque Wrench - LPT Coupling Nut856A2555 Lifting Beam - Fan Frame 856A2625 Storage Stand - LP Module856A2644 Tool Lock - Fan Disk

856A2655 Installation/Removal Fixture - Radial Drive Shaft Housings

856A2663 Puller Adapter - Splitter Fairing856A2694 Installation Tool - Inner Housing856A3501 Alignment/Guide Fixture - Booster to LPT Shaft856A3504 Pusher/Puller Fixture856A3524 Drive Adapter Tool Set - Booster & LPT 856A3702 Removal/Installation Centering Sleeve - MM3856A3703 Countertorque Wrench Guide856A3704 Residual Torque Beam856A3723 Guiding & Pulling Fixture - Booster856A3724 Tool Set - Sighting Fan Disk Coupling Bolts856A3725 Torque/Loosen Wrench - Fan Disk856A3732 Handling Fixture - Booster Rotor/Stator 856A5684 Eddy Current Inspection Kit - Fan Disk Inside Diameter856A5945 Alignment Master - LPT Shaft

#1 & #2 BEARING TOOLING PART

NUMBER: CFM INT'L

DESCRIPTION

856A2336 Puller - Forward Rotating Air/Oil Separator 856A2609 Jacking Block - Fuel Pump /MEC or HMU856A2626 Storage Stand - #1 & #2 Bearing856A2640 Holder - Oil Separator Duct856A2662 Tool Kit - Masters Air Nozzles 856A2667 Check Tool - Assembly/Disassembly Circular Runout856A2745 Thickness Gauge Tool - Phonic Wheel856A2923 Supporting Guide - #1 Bearing856A3011P01 Plug Extractor856A3012 Puller - #2 Bearing Inner Race (with Actuator)856A3013 Puller - #1 Sensor Ring (with Actuator)856A3033P01 Fixture - #1 Bearing Sleeve Nut Retaining856A3267 Adapter Test Rig - #1 & #2 Bearing Air Flow856A3323 Center Bushing - #1 Ball Bearing 856A3489 Targets Tool Set - #1 Bearing Air Impingement Checks856A3556 Axial Weight Loading - #1 Bearing856A3570 Wrench - #2 Bearing Inner Race Seal856A3571 Wrench - Forward Rotating Air/Oil Separator Nut 856A3572 Wrench - #1 Bearing Inner Race Nut856A3628 Installation Tool - #1 Bearing Inner Race856A3721 Lift & Turn Adapter Tool Set - #1 & #2 Bearing Support856A3722 Dummy - Fan Disk856A3736 Locating Template - Drain Tube & OilCORE MODULE TOOLING856A2812 Dolly Fixture - Torque HP856A2818 Dolly - Tool Seating Check Core HP856A2821 Lube Protective Washer - #4 Bearing Retainer856A2822 Torque Fixture - #4 Bearing Retainer 856A2868 Protector - Fan ShaftLOW PRESSURE TURBINE (LPT) MODULE TOOLING856A2568 Lifting Ring - Aft LPT Shaft856A2577P01 Locating Ring - #5 Bearing Rollers856A2600 LPT Shaft Guide & Stop Tool Guide856A2618 Holding Fixture - Rotor/Stator856A2647 Transportation/Storage Stand - LPT Major Module856A2660 Measuring Gauge - LPT Axial Clearance856A2661 Puller - Aft Rotating Air/Oil Separator 856A2674 Protection Cover - LPT Shaft856A2676 Checking Gauge - LPT MO1B Clearance (7BE)856A2677 Installation/Removal Fixture - Removable Retaining Ring

856A2685 Puller Adapter - Oil Inlet Cover (Hydraulic or Manual Option)

856A2692 Eddy Current Inspection Kit - TRF856A2702 Pin Guide - #5 Bearing

856A2710 Handling Fixture - LPT Major Module (also accommodates CFM56-5B engines)

856A2713 Build-Up Fixture - LPT Shaft Module to LPT Module856A2714 Hoist Fixture - LPT Module856A2722 Guide Pins - LPT Frame to LPT Case 856A2729 Handling/Turn Fixture - LPT Case856A2731 Support Sectors - LPT Shaft to LPT 856A2750 Fixture - Stages 1 through 4 LPT Blades856A2752 Restrain Hooks - Air Seal to LPT Disassembly856A2755 Tool Set - Seals to Cone Stub Shaft856A2756 Heater - LPT Shaft to Stub Shaft (110V or 220V Option)856A2759 Puller Seals Tool Set856A2760 Support Handle Ring - Cone Stub Shaft & Stage 3 Disk856A2764 Heater Set - LPT (110V or 220V Option)856A2766 Support Ring - Cone Stub Shaft856A2773 Support Spacers - LPT Rotor/Case 856A2789 Ring - Center Aft Rotating Air Seal856A2826 Holding Fixture - #4 Bearing Inner Race Bolts

LPT MODULE TOOLING (CONTINUED)PART

NUMBER: CFM INT'L

DESCRIPTION

856A2943 Protection Sleeve - Rear Inner Rotating Air/Oil Seal 856A2968 Heating Tool - Center Vent Tube (110V or 220V Option)856A3062 Puller - Rear Rotating Air/Oil Seal 856A3100 Locating Pin - Center Vent Tube 856A3234P01 Protector - Aft Center Vent Tube856A3268 Wrench - Center Vent Tube Sleeve Nut856A3269 Wrench - #5 Bearing Inner Race Nut856A3279 Pusher/Puller - LPT Disk Sleeves856A3308 Puller - #4 Bearing Inner Race856A3315 Puller - Center Vent Tube 856A3385P03 Wrench - Stage 1 LPT Disk Bolts856A3392 Torque Nut Wrench - Aft Rotating Air/Oil Separator856A3419 Puller Adapter - Oil Inlet Cover 856A3432 Gauge - LPT Stub Shaft to LPT Shaft856A3443 Puller - #5 Bearing Outer Race856A3483P01 Protective Ring - #4 Bearing856A3484P01 Protective Ring - #5 Bearing 856A3485P01 Protective Cap - LPT Shaft Thread856A3487 Protector - #4 Ball Bearing856A3488 Holding Fixture - Sectors Support 856A3491 Counter Wrench - #5 Bearing Support Nipple856A3492 Counter Wrench - #5 Bearing Support Nipple Line856A3501 Alignment/Guide Fixture - Booster to LPT Shaft856A3748 Protection Cover - Stage 1 LPT Disk856A3749 Installation Tool Set - Stages 2 & 3 Strips856A3750 Centering Fixture - LPT Shaft Module

856A3751 Holding Ring - Stage 1 Outer Stationary Air Seal & Turbine Shroud Support

856A3752 Removal Fixture - Stages 1-2-3 Outer Stationary Air Seal856A3755P01 Foolproof Installation Tool - Stage 1 LPT & Air Seal856A3756 Installation Fixture - Stage 2 Shield856A3757 Installation Fixture - Stage 3 Shield

856A3760 Assembly/Disassembly Fixture - Stage 2 LPT Nozzle Segments

856A3761 Installation Tool Set - Stage 2 LPT Outer Stationary Seal856A3762 Assembly/Disassembly Fixture - LPT Rotor/Stator

856A3763 Assembly/Disassembly Fixture - Stage 3 LPT Nozzle Segments

856A3764 Installation Tool Set - Stage 3 LPT Outer Stationary Air Seal

856A3766 Handling Fixture Support - LPT Rotor/Stator856A3767 Handling Fixture - LPT Rotor/Stator

856A3788 Installation Tool Set - Stages 2 & 3 LPT Outer Stationary Air Seal

856A3790 Pusher/Puller Fixture - Duct Rear856A3791 Machining Fixture Adjusting Sleeve - #5 Bearing856A3792 Centering Fixture - LPT Shaft to LPT856A3793 Pusher/Puller Fixture - Center Vent Tube

856A3794 Holding Ring - Stage 1 Outer Stationary Air Seal & Turbine Shroud Support

856A3795 Mobile Stand - LPT Module856A3799 Guide Pin - #5 Bearing Support 856A5944 Alignment Fixture - LPT ShaftENGINE SHIPPING, LIFTING & STORAGEAM-2563-227 Transportation Base (Wide Fork)AM-2811-4800 Shipping Cradle

856A1312 Engine Handling Support (also accommodates CFM56-5B engines)

856A2627 Lifting Beam856A2645 Engine Variable CG Beam856A2651 Engine Support Pad856A3515 Extension Beam - Variable CG Lift Fixture856A3700 Fitted Bar Engine Shipping Cover856A3710 Lifting Beam (2,000 daN/4,400 lbs Capacity)

Approved, qualified, and recommended by CFM International, GE Aviation, or Safran Aircraft Engines for the handling of CFM56-7B engines.

OEM-APPROVED FOR CFM56-7B ENGINE MODULES SELECT LINE, HANGAR &

SHOP MAINTENANCE TOOLING

High-Quality engine tooling for airlines, MRO shops, lessors, and OEM customers!

Contact AGSE Customer Service to Discover Additional OEM-Approved CFM56 Tooling!

7+1.513.402.7246 | www.agsecorp.com | toolingsales@agsecorp.com

LINE MAINTENANCE TOOLINGPART NUMBER:

CFM INT'L DESCRIPTION

856A2320 Tool Set - Engine Sumps Relube

856A2501 Dual Purpose Ratchet Wrench - VBV Manual Control

856A2537 Mounting Pin Protector - Accessory Drive Major Module

856A2609 Jacking Block - Fuel Pump/MEC or HMU

856A2645 Engine Variable CG Beam

856A2655 Fixture - Radial Drive Shaft Housings Installation/Removal

856A2659 Filter Adapter - Dry Out

856A2663 Puller Adapter - Splitter Fairing

856A2664 Setting Gauge - VBV Doors

856A2673 Installation Tool - Enerseal Seal

856A2677 Installation/Removal Fixture - Removable Retaining Ring

856A2678P02 CFMI Software - Trim Balance

856A2680 Vibration Software - #4 Bearing

856A2686 Hand Cranking Drive Socket

856A2689 Vibration Analyzer Kit

856A2707 Leak Test Tool Set - AGB

856A2717 Lock Adapter - Core Engine

856A2718 Tool Set - Manual Drive Shaft

856A2719 Removal/Installation Support Fixture - TGB

856A2727 Puller - Radial Drive Shaft

856A2737 Leak Test Tool Set - AGB

856A2754 Support Fixture - AGB

856A2794 Protector Set - Seal Fitting

856A2796 Safety Protector Handcranking Pad

856A2805 Turnbuckle - AGB/TGB

856A2809 Back-Up Filter Handle Removal

856A2930 QEC Engine Shipping Cover

856A2947 Fan Blade Contour Template

856A2948 Fan Blades Liner Patch Inflatable Pressure Tool (220V/50Hz)

856A2949 Fan Blade Leading Edge Template

856A2953 Guide Pins - Stator Alternator

856A3409 Guide Pins - Spinner Rear Cone

856A3471P02 Drive Spline Adapter Fuel Pump (US Configuration)

856A3492 Counter Wrench - #5 Bearing Support Nipple Line

856A3519 Three (3) Legs Handling Sling - AGB

856A3576 Removal/Installation Tool - AGB Seals

856A3770P03 Fan Blade Mapping Program Software

856A5649 Fan Disk Mirror Inspection

856A5817 Check Fan Blade Shank

856A5931 Fan Disk Dovetail Slots Gauge

856A5942 Fan Disk Dovetail Slots Gauge

FAN REMOVAL/INSTALLATION856A1312 Engine Handling Support (also accommodates CFM56-7B engines)

856A2555 Lifting Beam - Fan Frame

856A3111 Trunnion Dolly - Fan Frame Module

FAN ASSEMBLY/DISASSEMBLY856A1312 Engine Handling Support (also accommodates CFM56-7B engines)

856A2308 Centering & Removal/Installation Sleeve - Module 1/LPT Major Module

856A2310 Alignment Fixture - Booster to LPT Shaft

856A2311 Dummy Tube - LPT Rotor Shaft Forward End

856A2571 Guide Pins - #1 & #2 Bearing Support Module Installation

856A2625 Storage Stand - Fan & Booster Module

856A2626 Storage Stand - Module 2

856A2667 Check Assembly/Disassembly Tool - Circular Runout

856A2701 Protective Floor - Fan Inlet Case Turbine Frame

856A2720P49 Machining Fixture - Fan Case Abradable Strip

FAN ASSEMBLY/DISASSEMBLY (CONTINUED)PART NUMBER:

CFM INT'L DESCRIPTION

856A2753 Accessory Drive Dummy

856A2902 Dummy Fan Disk

856A2904 Handling Fixture - Booster Rotor/Stator Assembly

856A2906 Guide & Countertorque Wrench

856A2907 Machining Fixture - Abradable Strip Fan Casing

856A2951 Counterweight Tool

856A2986 Alignment Fixture - Guide Booster

856A3111 Trunnion Dolly - Fan Frame Module

856A3267 Test Rig Adapter - #1 & #2 Bearing Support Air Flow Check

856A3409 Guide Pins - Spinner Rear Cone

856A3510 Lift & Turn Adapter - Module 2

856A3515 Extension Beam - Variable CG Lift Fixture

856A3608 Axial Loading Fixture

856A5939 Tool - Fan Blade Tip Clearance

FAN & BOOSTER MODULE REMOVAL/INSTALLATION856A1312 Engine Handling Support (also accommodates CFM56-7B engines)

856A2308 Centering & Removal/Installation Sleeve - Module 1/LPT Major Module

856A2310 Alignment Fixture - Booster to LPT Shaft

856A2318 Thermal Shield

856A2501 Dual Purpose Ratchet Wrench - VBV Manual Control

856A2625 Storage Stand - Fan & Booster Module

856A2627 Lifting Beam

856A2631 Storage Stand - Fan Blades

856A2632 Puller

856A2644 Holding Tool - Fan Disk

856A2663 Puller Adapter - Splitter Fairing

856A2701 Protective Floor - Fan Inlet Case Turbine Frame

856A2780 Handling Adapter

856A2903 Torque Adaptation Beam

856A2904 Handling Fixture - Booster Rotor/Stator Assembly

856A2905 Torque/Loosen Wrench - Fan Disk Coupler

856A2906 Guide & Countertorque Wrench

856A2946 Protective Ring - Fan Disk

856A2951 Counterweight Tool

856A3111 Trunnion Dolly - Fan Frame Module

856A3504 Pusher/Puller Fixture - Module 1 & Major Module 3

856A3515 Extension Beam - Variable CG Lift Fixture

856A3524 Drive Adapter Tool Set - Booster & LPT

856A3793 Pusher/Puller Fixture - Center Vent Tube

856A5939 Tool - Fan Blade Tip Clearance

#1 & #2 BEARING SUPPORT MODULE REMOVAL/INSTALLATION856A1312 Engine Handling Support (also accommodates CFM56-7B engines)

856A2308 Centering & Removal/Installation Sleeve - Module 1/LPT Major Module 856A2310 Alignment Fixture - Booster to LPT Shaft 856A2316 Torque/Loosen Wrench - LPT Coupling Nut856A2571 Installation Guide Pins - #1 & #2 Bearing Support Module856A2616 Centering Sectors - Forward LPT Shaft856A2626 Storage Stand - Module 2856A2701 Protective Floor - Fan Inlet Case Turbine Frame856A2709 Forward Support Guide856A2780 Handling Adapter856A2902 Dummy Fan Disk856A2903 Torque Adaptation Beam856A2906 Guide & Countertorque Wrench856A2909 Guide Pins - #1 & #2 Bearing Tubes 856A3510 Lift & Turn Adapter - Module 2 856A3515 Extension Beam - Variable CG Lift Fixture

OEM-APPROVED FOR CFM56-5A/-5B/-5C ENGINE MODULES SELECT LINE, HANGAR &

SHOP MAINTENANCE TOOLING

Contact AGSE Customer Service to Discover Additional OEM-Approved CFM56 Tooling!

Guaranteed deliveries and round-the-clock after-sales service!

More Select CFM56-5A/-5B/-5C Tooling on Page 8

Approved, qualified, and recommended by CFM International, GE Aviation, or Safran Aircraft Engines for the handling of CFM56-5A/-5B/-5C engines.

8+1.513.402.7246 | www.agsecorp.com | toolingsales@agsecorp.com

CORE MODULE REMOVAL/INSTALLATIONPART NUMBER:

CFM INT'L DESCRIPTION

856A2812 Dolly Fixture - Torque HP

856A2818 Tool Seating Check Dolly - Core

856A2866 Protector - Fan Shaft

856A2946 Protective Ring - Fan Disk

856A2997 Seating Check Gauge - Core Module to IGB

HIGH PRESSURE TURBINE (HPT) TOOLING856A2821 Lubricant Shield (Protective Washer) - #4 Bearing Retainer

856A2822 Torque Fixture - #4 Bearing Retainer

LPT MODULE REMOVAL/INSTALLATION856A2308 Centering & Removal/Installation Sleeve - Module 1/LPT Major Module

856A2310 Alignment Fixture - Booster to LPT Shaft

856A2316 Torque/Loosen Wrench - LPT Coupling Nut

856A2412 Holding Ring - Stage 1 Outer Stationary Air Seal & Turbine Shroud Support

856A2600 Guide & Stop Tool - LPT Shaft

856A2618 Holding Fixture - Rotor/Stator

856A2627 Lifting Beam

856A2632 Puller

856A2647 Mobile Storage Stand - Horizontal Major Module 3

856A2661 Puller - Aft Rotating Air/Oil Separator

856A2668 Puller Adapter Kit

856A2685 Puller Adapter - Oil Inlet Cover

856A2710 Handling Fixture - LPT Major Module

856A2717 Lock Adapter - Core Engine

856A2780 Handling Adapter

856A2903 Torque Adaptation Beam

856A2906 Guide & Countertorque Wrench

856A2946 Protective Ring - Fan Disk

856A2950 Centering Fixture - LPT Shaft

856A2968 Heating Tool - Center Vent Tube (110V or 220V Option)

856A3234P01 Protective Cap - Center Vent Tube, Rear Extension Duct

856A3392 Torque Nut Wrench - Aft Rotating Air/Oil Separator

856A3419 Puller Adapter - Oil Inlet Cover & Major Module 3

856A3485P01 Protective Cap - LPT Shaft Thread

856A3487 Protector - #4 Ball Bearing

856A3504 Pusher/Puller Fixture - Module 1 & Major Module 3

856A3524 Drive Adapter Tool Set - Booster & LPT

856A3793 Pusher/Puller Fixture - Center Vent Tube

856A3794 Holding Ring - Stage 1 Outer Stationary Seal & Turbine Shroud Support

856A5944 Alignment Fixture - LPT Shaft

856A5945 Alignment Master - LPT Shaft

LPT MODULE DISASSEMBLY/ASSEMBLY856A2349 Assembly/Disassembly & Storage Dolly - LPT Shaft

856A2412 Holding Ring - Stage 1 Outer Stationary Air Seal & Turbine Shroud Support

856A2544 Trunnion Dolly - Turbine Frame Module

856A2567 Forward Lifting Eye - LPT Shaft

856A2568 Aft Lifting Eye - LPT Shaft

856A2577P01 Locating Ring - #5 Bearing Rollers

856A2618 Holding Fixture - Rotor/Stator

856A2627 Lifting Beam

856A2646 Trunnion Dolly - Turbine Frame Maintenance Module

856A2647 Mobile Stand - Horizontal Major Module 3 Storage

856A2710 Handling Fixture - LPT Major Module

856A2712 Handling Segments - Turbine Frame Module

856A2713 Buildup Fixture - LPT Shaft to LPT Module

LPT MODULE DISASSEMBLY/ASSEMBLY (CONTINUED)PART NUMBER:

CFM INT'L DESCRIPTION

856A2714 Hoist Fixture - LPT Module

856A2715 Storage Stand - LPT Module

856A2716 Distribution Ring

856A2722 Guide Pins - Turbine Frame to LPT Case

856A2731 Support Sectors - LPT Shaft to LPT Module

856A2756 Heat Diffuser - LPT Shaft (without Heat Gun)

856A2758 Centering Fixture - LPT Shaft to LPT

856A2772 Puller - LPT Rear Frame/LPT Case

856A2943 Protection Sleeve - Rear Inner Rotating Air/Oil Seal

856A2950 Centering Fixture - LPT Shaft

856A3234P01 Protective Cap - Center Vent Tube, Rear Extension Duct

856A3247 Alignment Guide - LPT Rear Frame to LPT Shaft

856A3383 Alignment Fixture - LPT Rear Frame to LPT

856A3484P01 Protective Ring - #5 Bearing

856A3485P01 Protective Cap - LPT Shaft Thread

856A3487 Protector - #4 Ball Bearing

856A3488 Holding Fixture Support - LPT Shaft

856A3759 Handling Sectors - Turbine Frame Module

856A3791 Machining Fixture Adjusting Sleeve - #5 Bearing

856A3792 Centering Fixture - LPT Shaft to LPT

856A3794 Holding Ring - Stage 1 Outer Stationary Seal & Turbine Shroud Support856A3795 Mobile Stand - LPT ModuleTURBINE FRAME MODULE REMOVAL/INSTALLATION856A1312G08 Engine Handling Support (also accommodates CFM56-7B engines)

856A2544 Trunnion Dolly - Turbine Frame Module

856A2627 Lifting Beam

856A2646 Trunnion Dolly - Turbine Frame Maintenance Module

856A2651 Engine Support Pad

856A2712 Handling Segments - Turbine Frame Module

856A2722 Guide Pins - Turbine Frame to LPT Case

856A2772 Puller - LPT Rear Frame/LPT Case

856A2773 Support Spacers - LPT Rotor/LPT Case

856A3234P01 Protective Cap - Center Vent Tube, Rear Extension Duct

856A3247 Alignment Guide - LPT Rear Frame to LPT Shaft 856A3383 Alignment Fixture - LPT Rear Frame to LPTINLET GEARBOX (IGB) & #3 BEARING MODULE REMOVAL/INSTALLATION856A2310 Alignment Fixture - Booster to LPT Shaft

856A2616 Centering Sectors - Forward LPT ShaftTRANSFER GEARBOX (TGB) MODULE REMOVAL/INSTALLATION856A2414 Fixture - Guide Radial Shaft

856A2537 Mounting Pin Protector - Accessory Drive Major Module

856A2632 Puller

856A2718 Tool Set - Manual Drive Shaft

856A2719 Remove/Install Support Fixture - TGB

856A2727 Puller - Radial Drive Shaft

856A2805 Turnbuckle - AGB/TGB

ACCESSORY GEARBOX (AGB) MODULE REMOVAL/INSTALLATION856A2537 Mounting Pin Protector - Accessory Drive Major Module

856A2609 Jacking Block - Fuel Pump/MEC or HMU

856A2632 Puller

856A2718 Tool Set - Manual Drive Shaft

856A2754 Support Fixture - AGB

856A2805 Turnbuckle - AGB/TGB

856A2953 Guide Pins - Stator Alternator

856A3519 Three (3) Legs Handling Sling - AGB

©2021 AGSE-Westmont Industries. All rights reserved. R.3.1.21

OEM-APPROVED FOR CFM56-5A/-5B/-5C ENGINE MODULES SELECT LINE, HANGAR &

SHOP MAINTENANCE TOOLING

Competitive pricing and expert consultation ensure an optimal Return on Investment!

Approved, qualified, and recommended by CFM International, GE Aviation, or Safran Aircraft Engines for the handling of CFM56-5A/-5B/-5C engines.

Contact AGSE Customer Service to Discover Additional OEM-Approved CFM56 Tooling!