GTO PARTS CATALOG #08.11D
Distributed by:
D.A.D.S., INC.1-800-442-9925dadsincorporated.com
MASTER DISTRIBUTOR OF GTO® & MIGHTY MULE® SWING & SLIDE GATE OPERATORS
5204 Calyx; Toledo, OH 43623-2215 419-472-2100
FAX 419-472-8953
GTO & Mighty Mule Service Parts
NOTICECustomer shall be responsible for making proper diagnosis for repairs and partsordering. Since we do not have the operator in front of us, repair tips receivedfrom DADS Personnel are merely suggestions and are not guaranteed to remedythe problem(s). Repair parts, if they are not needed or do not cure the problem,are not refundable. If the unit in Not in warranty, DADS recommends sending inthe complete unit for Authorized Service Center repairs if you are unsure of howto proceed. Service Center repairs will have no warranty unless the completeoperator (arm, control box, transformer, battery, cables & transmitter) are sent in.Repaired units will be returned programmed with factory defaults and will needto be reprogrammed. $3.00 handling surcharge on small orders under $20.00 (inaddition to shipping & handling charges).
REPLACEMENT ARMS ONLY# item MSRP MSDPMM250ARM Replacement Arm MM250 NLA NLAMM350ARM Replacement Arm MM350 (use PRO1500ARM) NLA NLAMM500ARM Replacement Arm w/6' cable, MM500-MM502 (1st Arm) 471.25 325.00MM502ARM Replacement Arm w/40' cable, MM502 (2nd Arm) 500.25 345.00PRO1000ARM Replacement Arm Only, PRO1000-1200-1800, FM700/702 (formerly F101) 427.75 295.00PRO1500ARM Replacement Arm SW1500 449.50 310.00PRO2000ARM Replacement Arm w/6' cable, PRO2000 (formerly F106) NLA NLAPRO2200ARM Replacement Arm w/50' cable, PRO2200 (formerly F150) NLA NLAPRO2000ARMXL Replacement Arm w/6' cable, SW2000XL 471.25 325.00PRO2002ARMXL Replacement Arm w/32' cable, SW2002XL 500.25 345.00PRO2500ARM Replacement Arm w/6' cable, SW2500 (1st Arm) 471.25 325.00PRO2550ARM Replacement Arm w/40' cable, SW2550 (2nd Arm) 500.25 345.00PRO2000ARMXL Replacement Arm w/6’ cable, PRO-SW2000XL 471.25 325.00PRO2002ARMXL Replacement Arm w/32’ cable, PRO-SW2002XL 500.25 345.00PRO3000ARM Replacement Arm w/6' cable, PRO-SW3000 NLA NLAPRO3200ARM Replacement Arm w/40' cable, PRO-SW3200 NLA NLAPRO3000ARMXL Replacement Arm w/6' cable, PRO-SW3000XL 529.25 365.00PRO3200ARMXL Replacement Arm w/40' cable, PRO-SW3200XL 543.75 375.00PRO4000ARM Replacement Arm w/6' cable, PRO-SW4000 NLA NLAPRO4200ARM Replacement Arm w/50' cable, PRO-SW4200 NLA NLAPRO4000ARMXL Replacement Arm w/6' cable, PRO-SW4000XL 558.25 385.00PRO4200ARMXL Replacement Arm w/50' cable, PRO-SW4200XL 572.75 395.00
Card Verification Required on orders over $100.00
NOVUS
Pricing eff. 3/1/08 subject to change
CROSS REFERENCEGTO Mighty Mule DatesGTO Pro100 x pre 1995GTO Pro1000 FM700 1995-2004GTO Pro 1800 x pre 1995-1997GTO Pro 2000 x 1997-2004GTO Pro SW1500 MM350 2005-GTO Pro SW2500 MM500 2005-GTO Pro SW3000 x 2004-2006GTO Pro SW4000 x 2004-2006GTO Pro SW3000XL x 2006-GTO Pro SW4000XL x 2006-GTO Pro SW2000XL x 2007-GP-SL100/SL050 x 2007-GP-SW100/SW050 x 2007-March of 2000: 1000 & 2000 upgraded to new UL325 specs. UL325recommends specific safety standards for gate operator systems. Allsystems manufactured since March of 2000 are UL325 complient.
®
Page 1 * Dealer Parts Catalog 08.11 * All Pricing Subject to Change
When replacing a SW3000/SW3200 or SW4000/SW4200 Non-XL Arm with a XL Arm, you must insure that thecontrol board is compatible with the newer arm. On the controlboard there are three (3) computer chips (1 square and 2rectangular). The Top 2 chips (1 square and 1 rectangular) mustbe labeled Rev 4 (4th revision). If not, you will need to purchase
and install a Generation III Control Board (R4207 or R4211).If you are replacing only one arm in a dual
installation, the second arm also must be upgraded by purchasingand installing a R4200XL Motor, RVCTBDXL Rev Counter andRCCCUPXL Rev Counter Cup.
ARM SUBSTITUTIONS
Radios (Receivers/Transmitters)AQ201C (black) Receiver Assembly w/Antenna & 10' cable w/removable plug 104.00 LA 65.00AQ201 (black) Receiver Assembly w/Antenna & 10' cable 104.00 65.00
AQ201-NB (gray) Receiver Assembly, Narrow Band w/Antenna & 10' cable w/removable plug. 72.00 45.00AQ201-100-NB Receiver Assembly, Narrow Band w/Antenna & 100' cable. Special Use 104.00 65.00AQ202 (black) Receiver Assembly w/Antenna & 20' cable. Slide Operators 61.25 LA 43.75AQ202-NB (gray) Receiver Assembly, Narrow Band w/Antenna & 20' cable. Slide OperatorsRB709 (indoor) Receiver Assembly, Garage Door. w/Antenna 83.20 LA 52.00RB709U-NB (black) Receiver Assembly, Universal, 2 channel. Narrow Band w/Antenna
Control BoardsAQ230 PC Board, Basic Operator, 1/2 HP, SL5000 & SW5000 -UL Call .For AvailabilityAQ231 PC Board, Basic Operator, 1 HP, SL6000 & SW6000-UL Call .For AvailabilityAQ240 PC Board, Adv. Operator, 1/2 and 1 HP, Swing and Slide-UL Call .For AvailabilityAQ200 Control Board, pre-1999, 12 volt, PRO1000 MM700/702 99.00 LA 69.00 LAAQ250 Control Board, UL-325, 12 volt, PRO1000 MM700/702 255.20 159.50
(Needs RB566 transformer when upgrading)AQ251 Control Board, UL-325, 12 volt, PRO2000, PRO-SL-1000, PRO-SL-1000B 275.20 172.00
(Needs RB570 transformer when upgrading)AQ252 Control Board, UL-325, 12 volt, SL2000/SL2000B 275.20 172.00GP4231 Drive Board for GP Series 432.00 270.00GP4232 Logic Board for GP Series 345.60 216.00MM500PCB PC Board, Mighty Mule FM500-UL325 use .R4211MM502PCB PC Board, Mighty Mule FM502-UL325 use .R4211PRO3040PCB PC Board for MM500/502, SW2500/3000/4000-UL325] use .R4211R4207 PC Board [Replacement/Upgrade PC Board for (PRO3040PCB) 281.60 LA 176.00 LAR4211 PC Board , 3rd Generation “Blue Board”.
For following Series: 500,2000XL,2500,3000,4000 361.60 226.00R4052 PC Board, SW1500/MM350 - UL325 280.00 175.00REWPOTPCB01 PC Board w/tuning pot for Exit Wands 30.00 18.75
Revolution Counter Boards (located d in late model arms)RVCTBD3040 Rev Counter Board (SW3000/4000) 3" long, 1" wide, sensor at end 36.00 22.50RVCTBDXL Rev Counter Board (SW3000XL/4000XL) 1-13/16” long, 1" wide, sensor near middle. 37.60 23.50RVCTBD50 Rev Counter Board (MM500) 3" long, 1-3/8" wide. 23.20 14.50
Lock Boards for Latching and Magnetic swing gate locksAT400-BD Lock Board for early Bulldog w/large format control box (6 pins) 24.82 LA 14.00 LAAT400 Lock Board for FM142 & FM144, plug-in type. Used through Phase 8 (5 pins) 24.82 LA 14.00 LALOCKPCB Lock Board for FM142 & FM144, wired type (Formerly AT401). 35.20 22.00
Control Boxes with/without Control BoardsAQ150 Control Box w/Board & Receiver (no battery or transformer), PRO1000-UL Only .NLA .NLAAQ152 Control Box w/Board & Receiver (no battery or transformer), PRO2000-UL Only 422.40 LA 264.00PRO2500CBOXASYMT Control Box, cover, harness, switch, alarm, standoffs & cover screws.SW2500 100.24 62.65PRO3040CBOXASYMT Control Box, cover, harness, switch, alarm, standoffs & cover screws. SW3000/4000 108.08 67.55FM317 “Big Box” Oversize Control Box for additional accessories, etc.
14” w X 16” h X 6” d ABS, metal backing plate. 232.00 145.00R4400 Extra Large Box 18" W x 8" D x 18" H, ventilated.
Will accomodate a large automotive or marine battery X 126.50
POWERRB422 Battery, Gelpack, 12 volt, 1.2 Ah, for New Style Bulldog Lock & MM250 28.80 18.00RB500 Battery, Gelpack, 12 volt, 7 Ah, Std for all DC Operators except MM250 34.40 21.50RB502 Transformer, 14v 10va AC, PRO1000, 2000, SL1000 Pre-UL boards (Sub for RB419) 26.96 15.85RB566 Transformer, 18v 20va,AC PRO1000,MM UL-325 Units** 26.96 16.85RB570 Transformer,18v 40va,ACPRO2000, SL1000-2000UL-325 Units, 3000, 4000 **
(** RB566 & RB570 willnotwork onpre-UL boards as the voltage is too high) 29.60 18.50
# item MSRP Dealer
Radio System CompatibilityAQ201 receiver, black Accepts both old and new (Narrow Band) Transmitters/KeypadsAQ201-NB receiver, gray Accepts only new (Narrow Band) Transmitters/Keypads
CONTROL BOARDS, ELECTRONICS, POWERNO REFUNDS ON CIRCUIT BOARDS • NO WARRANTY ON BURNT BOARDS
LA = Limited availability. Scheduled to go Out of Production. Our supply, if any, will become unavailable without notice.Call For Availability = Out of Production item. We may be able to get them from GTO if they have some left.
AQ200 (phase 9) 14 voltpre-UL Board for Pro1000& FM700. Upgrade/Rewireto AQ250 board or Replacewith AQ150 Box. Upgraderequires RB566Transformer.AQ210 18 volt boardrequires removal of 6 voltbattery and converting to
AQ250
AQ227 14 volt pre-ULBoard for PRO2000.Upgrade to AQ251board or Replace withAQ152 Box. Upgraderequires RB570Transformer.
AQ250 & AQ251Boards. (Check label for
correct board.)AQ250 is BackwardsCompatible to Pro1000Operators using 5 pins inarm plug. If 6 pins are in
the arm plug, replace entiresystem. Rewiring is required for upgrades
and can be avoided by purchasing the entire controlbox (battery & transformer not included)AQ250 uses RB566 TransformerAQ251 uses RB570 Transformer
R4207-R4211 Boards.• Better Soft Stop/Start Functions• Smoother Hookup • Plug & Playjust like 3040 • Easier to set limitfor dual application, it has master& slave button and not dipswitches • Increased surge protec-tion on accessory terminals • AutoClose potentiometer will set 3-120seconds, not with dip switches asprevious version that only gave 4options • Improved Charging cir-cuit will charge all the time; Thebattery will be charged in stagesnot charge to full and then stop • The circuit board pulls 25 milliamps not 40 like the oldboard. It is better for solar applications • Battery connectors are at the top and soldered onand not plug in like the 3040 board – we used to have to suggest tightening previously •Sequencing is automatically set for dual application. The slave will always close first.
Page 2 * Dealer Parts Catalog 08.11 * All Pricing Subject to ChangeLOCKPCBFM317
RB502RB566RB570
RB500*
RB422*
*RB500Used in all operators 1990-current except FM250.Used in Bulldog (large box-prior to 1997)2-1/2” W x 5-7/8” L x 3-7/8” H (inc. term.)
*RB422Used in FM250 operatorand Bulldog (small box-since 1997)1-7/8” Wx 3-13/16”Lx 2-3/16” H (inc. term.)
AQ152
PRO3040CBOXASYMT
PRO2500CBOXASYMT
Page 3 * Dealer Parts Catalog 08.11 * All Pricing Subject to Change
39
22
23 24
40
41
25
29
26
27
28
31
32
30 3334
32
33
35
19 3
14
13
4
2
120
12
2117
16
18
3
56
7
8
45
11
38
6
1
9
40
41
12
1
10
39
37
37
3642
15
Kit Name Kit Number Parts IncludedMotor Housing Cover R9041 38Limit Switch Nut Insert - Sold only as a 5 pack 506IH-5PK 14Gear Motor Assembly A204 3, 4, 5, 6, 7, 8, 13, 30, 32, 33, 34, 35Front End Assembly (Includes #14) A217 1, 2, 14, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 31Front Mount Repair Kit FM313 22, 39, 40, 41Rear Mount Repair Kit FM314 9, 11, 12, 39, 40, 41Sensor Switch Repair Kit FM315 15, 36, 37, 42Mounting Hardware Kit HB100 50 (2), 51, 52, 53Flat Post Bracket for square posts 349IH 2 required per arm. Priced separately* Part #14 is included with Kit #4 or sold individually as Kit #2 (5 pack). Part #14 is not included with Kit #3.
For Complete Arms see Page 1. For Electronics, see Page 2. For Kits & Parts see Page 8
A204Gear Motor
Assembly
A217Front EndAssembly
A217
A204FM315Sensor SwitchAssembly
Arm forGTO-PRO1000GTO-PRO-1200GTO-PRO1800
Mighty Mule FM700Mighty Mule FM702
Power Cables4’ Single plug AW2014’ Double plug AW20325’ Double plug AW20440’ Single plug AW24040’ Double plug AC109Some plug into the bottomof the control box and somego into the control box andwire directly to the mainboard.
50 5051
52
53
Complete Arm
Out Of Production Modelparts subject to discontinuation
without notice
349IH Flatpost bracket
Arm Parts only available as kits, as listed below.Individual parts not available from manufacturer
RB461 RB460RB4732 Rq’d
RB476 RB465474IH
RB471-RB472 RB470
453IH
Motor & Tube Not Servicable
Arm forGTO-PRO-2000 GTO-PRO-2200
Power Cables6’ AW20950’ AW210
Out Of Production ModelParts subject to discontinuation
without notice!
NLA
RB457
NLA
NLA
NLA
NLA
NLA
Only the following parts were available at the timeof this catalog publication.
453IH Bracket, Rear MountRB476 Rear Cover w/Pins, Bushing & CamsRB473 Limit Switch (2 rqd).HB200 Mounting Hardware (brackets)H200HD Hdw Bag (less brackets)AW209 6’ Power CableAW210 50’ Power Cable
HB200
NLA
NLA
No Longer Avail
No Longer Avail
Page 4 * Dealer Parts Catalog 08.11 * All Pricing Subject to Change
Kit Name Kit Number Parts IncludedFront Mount Kit FTMT5030 1,2Power Cable Kit 6' PCK506 3,5Power Cable Kit 32' PCK2232 4,5Scraper Seal Kit R4404 6,7Housing Kit R4415 8,9,10,11Rear Mount Kit R4430 12,13,14,15Rev Counter Wheel RVCCUP50 16Rev Counter PC6 RVCTBD3040 17Mounting Hardware Kit HB100 50 (2), 51,52,53Mounting Hdw Kit (less brackets) H101P not shownFlat Post Bracket for square posts 349IH 2 required per arm. Priced separatelyFor Complete Arms see Page 1. For Electronics, see Page 2. For Kits & Parts see Page 8
50 5051
52
539349IH Flatpost bracket
10
Discontinued Parts. Replace Entire ArmRAW2000XLARM (18) Gear Motor/Front End
Assembly, SW2000XL
SEAL TUBE (19)
5
5
12
13
15
14
4 3
10
9
17
8
16
18
7
6 2
1
11
Arm forGTO-PRO-SW2000XLGTO-PRO-SW2002XL
19
Arm Parts are only available as kits (as listedherein). Individual parts are not available from themanufacturer. Complete arms & most assembliesare stocked at DADS. Some assemblies partsare special order. Allow 3 weeks plus additionalshipping on special order items.
10
Arm forGTO-PRO-SW1500 Mighty Mule FM350
11 10
27
26 25 18
17
28
29
30 32
31
19
16
33
15 14 1312
1011
35
34
37
36
39
38
23
2120
24
22
Decals and coloring on some parts/seals mayvary between Mighty Mule and GTO ProModels.
Arm Parts are only available as kits (as listed herein). Individual partsare not available from the manufacturer. Complete arms & mostassemblies are stocked at DADS. Some assemblies parts are specialorder. Allow 3 weeks plus additional shipping on special order items.
Discontinued Parts. Replace Entire ArmRAW1500ARM (16)Gear Motor/Front End Assembly, SW1500RAW350ARM (16)Gear Motor/Front End Assembly, FM350
Kit Name Kit Number Parts IncludedFront Mount Kit FTMT5030 12,13Scraper Seal Kit Grey MM350 R4401 14,15Scraper Seal Kit SW 1500 R4402 14,15Housing Kit Grey MM350 R4411 19,20,21,22,23,24Housing Kit SW 1500 R4412 19,20,21,22,23,24Rear Mount Kit R4430 25,26,27,28,29,30Rev Counter Board RVCTBD50 31,32Limit Switch Harness R4054 33Battery/Power Cable Harness R4059 34,35Antenna Receiver AQ201 36Printed Circuit Board MM350 R4052 37,38,39Mounting Hardware Kit (brackets) HB100 50 (2), 51,52,53Mounting Hdw Kit (less brackets) H101P not shownFlat Post Bracket for square posts 349IH 2 required per arm. Priced separatelyFor Complete Arms see Page 1. For Electronics, see Page 2. For Kits & Parts see Page 8
2a
2b
3a
3b
10
11
3a/b
2a/b
50 5051
52
5310
349IH Flatpost bracket
11
No Longer Avail
No Longer Avail
No Longer Avail
No Longer Avail
50 5051
52
538
349IH Flatpost bracket
9
Arm Parts are only available as kits (as listed herein).Individual parts are not available from the manufacturer.Complete arms & most assemblies are stocked atDADS. Some assemblies parts are special order. Allow3 weeks plus additional shipping on special order items.
Kit Name Kit Number Parts IncludedFront Mount Kit FTMT5030 10,11Scraper Seal Kit R4402 12,13Housing Kit R4413 14,15,16RearMount Kit R4430 17,18,19,20,21,22Rev Counter Board RVCTBD50 23,24Power Cable Kit 6' PCK506 25,27Power Cable Kit 40' PCK5240 26,27Mounting Hardware Kit HB100 50 (2), 51,52,53Mounting Hdw Kit (less brackets) H101P not shownFlat Post Bracket for square posts 349IH 2 required per arm. Priced separatelyFor Complete Arms see Page 1. For Electronics, see Page 2. For Kits & Parts see Page 8
Arm forGTO-PRO-SW2500 • GTO-PRO-SW2550
Mighty Mule FM500 • Mighty MuleFM502
Unavailable Parts. Replace Entire ArmRAW2500XLARM (29)Gear Motor/Front End Assembly, SW2500RAW500XLARM (29)Gear Motor/Front End Assembly, SW500
26
27
25
8 9
20
19
17
18
21 22
28
23
24
29
15
1311
10
89
16
14
27
12
28
Page 5 * Dealer Parts Catalog 08.11 * All Pricing Subject to Change
Kit Name Kit Number Parts IncludedFront End Assembly SW3000 FEA30 11,12,13,14Front Mount Repair Kit SW3000 FTMT5030 17,18Aluminum Housing Kit R4414 19,20,21Gear Motor SW3000/3200 GMTR40 22Gear Motor SW3000XL/3200XL R4200 22Rev Counter Board SW3000/3200 RVCTBD3040 23,24Rev Counter Board SW3000XL/3200XL RVCTBDXL 23,24Power Cable Kit 6' SW 3000 PCK30406 25,27Power Cable Kit 40' SW 3200 PCK3240 26,27Scraper Seal Kit 3000 R4404 28,29Mounting Hardware Kit HB300 50 (2), 51,52,53Mounting Hardware Kit HB301 as shownMounting Hdw Kit (less brackets) H101P not shownFor Complete Arms see Page 1. For Electronics, see Page 2. For Kits & Parts see Page 8
Arm Parts are only available as kits (aslisted herein). Individual parts are notavailable from the manufacturer. Completearms & most assemblies are stocked atDADS. Some assemblies parts are specialorder. Allow 3 weeks plus additionalshipping on special order items.
9 10
19
27
2627
25
20
23
24
152216
1514 13 12
21
4a/b
5a/b
11
29
28
10
9
1718
Arm forGTO-PRO-SW3000GTO-PRO-SW3200
GTO-PRO-SW3000XLGTO-PRO-SW3200XL
5a
5b
4b
4a
50 5051
52
53
Product Change
SW3000XL Series
o p e r a t o r s
m a n u f a c t u r e d
b e g i n n i n g
approximately 10/1/08
started coming with flat
post hardware similar to
4000XL hardware, but,
lighter weight. New
Push-To-Open Bracket
is R4388.
R4388PTO HB301
9
10
10
No Longer Avail
No Longer Avail
Page 6 * Dealer Parts Catalog 08.11 * All Pricing Subject to Change
Kit Name Kit Number Parts IncludedFront End Assembly SW4000 FEA40 11,12,13,14Front Mount Repair Kit SW4000 FTMT40 17,18Aluminum Housing Kit R4414 19,20,21Gear Motor SW4000/4200 GMTR40 22Gear Motor SW4 000X174200X1 R4200 22Rev Counter Board SW4000/4200 RVCTBD3040 23,24Rev Counter Board SW4000XL/4200XL RVCTBDXL 23,24Power Cable Kit 6' SW 4000 PCK30406 25,27Power Cable Kit 50' SW 4200 PCK4250 26,27Scraper Seal Kit 4000 R4404 28,29Mounting Hardware Kit (brackets) HB400 50,51,52,53Mounting Hdw Kit (less brackets) H200HD not shownFlat Post Bracket for square posts 349IH 2 required per arm.
Priced separatelyForCompleteArms see Page1. For Electronics, seePage2.ForKits & PartsseePage 8
5a
5b
4a
10
Arm forGTO-PRO-SW4000 • GTO-PRO-SW4200
GTO-PRO-SW4000XL • GTO-PRO-SW4200XL
R4KRDPOST4Round Post
Adaptor (2 rq’d)
R4KRDPOST6Round Post
Adaptor (2 rq’d)
R4KRDPOSTNARROW4Round Post Adaptor
(2 rq’d)(Optional Adaptors are used with the R4KPOST Brkt. 1 on top, 1 on bottom)
Arm Parts are only available as kits (as listed herein). Individualparts are not available from the manufacturer. Complete arms &most assemblies are stocked at DADS. Some assemblies partsare special order.Allow 3 weeks plus additional shipping on specialorder items.
5051
5352
9
27
910
19
26
27
25
20
21
22
24
23
15 16 1514 13 12
1718
10
28
29
11
4a/b
5a/b
9
4b
The following AC operator models have ceased production.
GTO/PRO SL-5000 GTO/PRO SW-5000GTO/PRO SL-6000 GTO/PRO SW-6000
A limited quantity of parts are available and are being rationed by the manu-facturer. While the purchase will be made through DADS, the parts willneed to be drop shipped to you from GTO.
6BLUE
5GREEN
4BLACK
9BLANK
8BLANK
7BLANK
3ORANGE
2WHITE
1RED
PRO1000/MM7001st Generation Swing Gate Arm
Power Cable Wiring ChartViewed upstream towards cable
(Looking into end of plug)
GTO To Mighty Mule Cross Reference ChartSimilar products may have slight variations in color and/or packaging.
(See front page for cross reference of arms.)
GTO PRO Mighty Mule
347IH FM148 Bracket, Push to open348IH FM149 Old PTO BracketF310 FM137 Keypad
F3100 FM136 Intercom, 1st generationF3100MBC FM136 Intercom, 2nd generation
F100 FM100 PedestalFM122 FM121 5 watt SolarFM139 FM138 Exit WandFM144 FM143 Gate Lock, Pull to openFM345 FM133 Pin LockFM400 FM124 Light KitRB101 FM132 Push ButtonRB422 FM152 Battery, 1.5 ampRB500 FM150 Battery, 7 ampRB741 FM135 Transmitter, 1 buttonRB741 FM134 Transmitter, 2 button
Page 7 * Dealer Parts Catalog 08.11 * All Pricing Subject to Change
SL1000, SL1200SL1000B, SL1200BSL2000, SL2200SL2000B, SL2200B
Diagram 1 (Top)Kit Name Kit Number Parts IncludedControl Box w/Board & Battery, Less Receiver AQ151 30,31,32Gear Motor w/o Brake (SL1000/1200) RB200 Gear Motor, 18Gear Motor w/Brake (SL1000B/1200B) RB200B Gear Motor, 18DC Slider Limit Switch and Plate Kit R4420 12, 13, 14, 15, 21, 22, 23, 24, 25, 27, 33DC Slider Limit Switch Kit (2 required each) R4421 23,24,25DC Slider Limit Nut Kit R4422 20Wire Harness for Gear Motor AC201 34Diagram 2 (Bottom)Kit Name Kit Number Parts IncludedDC Slider Sprocket Assembly Kit R4423 2,3,4,5,6,7,8,9,10,11,12,13,14,1 5,18Optional Pad Mount Kit SGMP as shownReplacement Cover A207 outer cover only, blackReplacement Chain RB207 chain, 32’Replacement Chain Bracket Kit R4630 Formerly 207IHReplacement Chain Pin Kit (not shown) R4631 Quick Release Pins that slip into chain bracket
2b
2a
Diagram 1
Diagram 2
12
12
13
13
28
29
2033
18
25
27 31
26
31
19
31
30
32
14
15
1415
23
24
25
24
23
22
21
25
34
1416
14 1614
15
14
15
18
10
11
17
6
197
5
8
9
12
13
12
13
4
23
2a/b
The above diagram is todemonstrate mounting and isnot part of any kit
For Electronics, see Page 2
Page 8 * Dealer Parts Catalog 08.11 * All Pricing Subject to Change
349IH Flat Post Bracket for square posts.2 required. Price each NLA NLA
453IH Bracket, Rear Mount, PRO2000 18.16 11.35*506IH Limit Switch Nut, Insert Single. PRO1000 10.68 6.80*506IH Limit Switch Nut, Insert 5 Pack. PRO1000 40.70 25.44A204 Gear Motor Assembly. PRO1000 279.84 174.90A207 Replacement Cover, outer cover only, black 130.59 81.62A217 Front End Assembly. PRO1000 164.09 102.56AC109 Power Cable, 40’ Dbl Plug. PRO1000 144.16 90.10AC201 Wire Harness for Gear Motor 26.29 16.43AQ151 Control Box w/Board/Battery, w/o Receiver 422.40 264.00*AW201 Power Cable, 4.5’ Sgl Plug. PRO1000 54.27 33.92AW203 Power Cable, 4.5’ Dbl Plug. PRO1000 110.24 68.90AW204 Power Cable, 25’ Dbl Plug. PRO1000 127.20 79.50AW209 Power Cable, 6’ PRO2000 39.20 24.50*AW210 Power Cable, 50’ PRO2000 139.60 87.25*AW240 Power Cable, 40’ Sgl Plug. PRO1000 110.24 68.90FEA30 Front End Assembly SW3000 Spec XL or not 303.58 189.74FEA30 Black Front End Assembly SW3000 Spec XL or not 303.58 189.74FEA40 Front End Assembly SW4000 Spec XL or not337.50 210.94FM313 Front Mount Repair Kit. PRO1000 24.59 15.37FM314 Rear Mount Repair Kit. PRO1000 33.07 20.67FM315 Sensor Switch Repair Kit. PRO1000 71.23 44.52FTMT40 Front Mount Repair Kit SW4000 24.59 15.37FTMT5030 Front Mount Kit.
1500/350/2000XL/2500/500/3000 24.59 15.37GMTR40 Gear Motor SW3000/SW4000 Series 232.00 145.00*H101P Hdw Bag (less brackets)
500/1500/2500/3000/3200 23.32 14.58H200HD Hdw Bag (less brackets)
PRO2000/SW4000 46.08 28.80HB100 Mounting Hardware Kit (brackets)
(inc: 350IH (2), 351IH, 352IH, 353IH) 84.00 52.50*HB200 Mounting Hardware (brackets) PRO2000
(inc: RB451 (2), RB450, RB452) 57.60 36.00*HB300 Silver Bracket Set for 2000/3000 swing 64.40 40.25HB301 Black Brkt Set (square) for 3000 swing 86.40 54.00HB4000 Mounting Hardware Kit (brackets)
(inc: R4KGate, R4KPost, R4KPivot, 351IH) 123.47 77.17PCK506 Power Cable Kit 6' MM500/SW2500 31.80 19.88PCK2232 Power Cable Kit 32' cfp cfpPCK30406 Power Cable Kit 6' SW3000/SW4000 48.60 30.38PCK3240 Power Cable Kit 40' SW 3200 168.00 105.00PCK4250 Power Cable Kit 50' SW4200 199.68 124.80PCK5240 Power Cable Kit 40' 500/2500 98.37 61.48R4054 Limit Switch Harness 1500 9.60 6.00R4059 Battery/Power Cable Harness 380/1500 28.83 18.00R4200 Gear Motor SW3000XL/SW4000XL Series279.84 174.90R4401 Scraper Seal Kit, Grey MM350 22.61 13.52R4402 Scraper Seal Kit, Black 500/1500/2500 24.17 15.11R4404 Scraper Seal Kit. Blk. 2000XL/4000/3000 21.20 13.25
Replacing GTO Intercom ModulesThe easiest way to tell the 1 st generation intercom from the 2 nd
generation intercom is to look at the base. The base on the 1 st generationintercom is ivory colored. The base on the 2 nd generation is black colored.The keypad is a little harder. The 1 st generation keypad had the GTOPRO logo on a sticker on the face at the bottom. The 2 nd generation keypadhas the GTO PRO logo stenciled onto the face of the housing itself at thebottom.
Parts for the 1 st generation intercom are not compatible withthe parts of the 2 nd generation intercom. The 1 st generation intercom willnot accept multiple base stations. The 2 nd generation intercom will acceptup to a total of four base stations provided they are within range. DADSstocks modules for the 2 nd generat ion intercom. Modules for the 1 st
generation intercom are special order.
1st Generation 2nd GenerationF3110 Keypad-Intercom Module F3110MBC Keypad-Intercom Module
Ivory base Black baseF3101 Base Station & xformer F3101MBC Base Station & xformer
Sticker logo Stenciled logo
R4411 Housing Kit, Grey 350 105.58 65.99R4412 Housing Kit, Blk. SW1500 104.73 65.46R4413 Housing Kit, Blk. 500/2500 109.36 68.37R4414 Aluminum Housing Kit, 3000/4000 137.90 86.19R4415 Housing Kit, 2000XL 127.20 79.50R4420 DC Slider Limit Switch and Plate Kit 91.50 57.19R4421 DC Slider Limit Switch Kit (2 required each)35.70 22.31R4422 DC Slider Limit Nut Kit 16.11 10.07R4423 DC Slider Sprocket Assembly Kit 81.41 50.88R4430 Rear Mount Kit 350/500/1500/2500 36.46 22.79R4630 Chain Bracket Kit for DC sliders (207IH) 76.32 47.70R4631 Chain Pin Kit for DC sliders 16.96 10.60R4KRDPOST4 Round Post Adaptor (2 rq’d) 44.80 28.00R4KRDPOST6 Round Post Adaptor (2 rq’d) 44.80 28.00*R4KRDPOSTNARROW4 Round Post Adaptor (2 rq’d) 38.40 24.00*R9041 Cover, Motor Housing. PRO1000 31.68 19.61RB200 Gear Motor w/o Brake (SL1000/1200) 473.20295.75*RB200B Gear Motor w/Brake (SL1000B/SL1200B) 568.80355.50*RB207 Replacement Chain, 32' 91.58 57.24RB208 Master Link for RB207 3.39 2.12*RB473 Limit Switch. PRO2000.
2 required. Price each 24.59 15.37RB476 Rear Cover w/Pins, Bushing & Cams.
PRO2000-2200 110.24 68.90RVCCUP50 Rev Counter Wheel, 350/1500 19.20 12.00*RVCTBD50 Rev Counter Board, 350/500/1500/2500 24.59 15.37RVCTBD3040 Rev Counter Board 2000XL, SW3000/4000 38.16 23.85RVCTBDXL Rev Counter Board
SW3000XL/SW4000XL Series 39.86 24.91SGMP Optional Pad Mount Kit 188.14 129.75
cfp = Call for Pricing & Availability
PRE_UL325 SWING GATE CONTROL BOARD HISTORYPhase 1-3 Research Boards, Not in usePhase 4 (pre-90) No Lights
Upgrade required to Phase 9 = Extensive, Not RecommendedPhase 5 (90-92) 1 Red light in center
Upgrade to Phase 9 If arm(s) have 6 pins(88-91), limit(s) must be upgradedPhase 6 (1992) Green Board- 2 Red, 1Yellow, 1 Green light and White R1 & R2 Resistor on left side of board
Upgrade to Phase 9Phase 7 (92-95) Beige Board- 2 Red, 1Yellow, 1 Green light and White R1 & R2 Resistor on left side of board
Upgrade to Phase 9Phase 8 (95-10/95) Beige Board- 2 Red, 1Yellow, 1 Green light and Pink R1 & R2 Resistor on left side of board(PRO100 & 200) Upgrade to Phase 9Phase 9 (11/95-on) Green Board- 1 Red, 1 Green light and 2 10 amp auto type fuses. Screw type connections.(PRO1000 & 1200) Upgrade required = If arm(s) have 6 pins(88-91), limit(s) must be upgraded
Board Re-Booting InstructionsResets Board to Factory Defaults (Settings)
Hold 3-4-5 in while turning on
18Volt Boards (PRO1800) are identified by: longer battery leads (to reach 12v & 6v)18Volt Boards follow essentially the same formats and required upgrades / modifications.
PRE-UL325 SWING GATE CONTROL BOARD HIS-TORY
AQ200
Symptoms Possibly Indicating A Bad Rev Counter Board1. Interrupt Alarm goes on-off-on-off-etc.
a. Check Power cable for cuts/splices/bad connectionsGo to the Active Dealer Section of dadsincorporated.comfor testing procedure instructions (1 document1)
2. Arm ReversesGo to the Active Dealer Section of dadsincorporated.comfor testing procedure instructions (2 documents)
Clearing BoardsPRO3040PCB
Single arm resetWith arm retracted, and switch # 4 off, push “set limit” button for 10 secondsSlave arm arm reset (after doing single arm reset)With arm retracted, and switch # 4 on, push “set limit” button for 10 secondsReprogram per owner’s manual
R4207/R4211Single arm installationWith arm retracted, push “learn master limit” until it beepsDual arm installationWith arms retracted, push “learn master” until it beeps.With arms retracted, push “learn slave limit” until it beepsReprogram per owner’s manual
# Description MSRP MSDP
# Description MSRP MSDP* after the price indicates a discontinued part. We may be out of stock