Gyt Tf Report Glio8590

7/31/2019 Gyt Tf Report Glio8590

1/21Page 1 of 21

Report NumberGLIO 8590 Rev 1

Technical File

Describing the Construction Details and Testing of the

SOLAR GUARD DISPLAY ST0443FOR

GYT SAN DIEGO, INC

2006/95/EC Low Voltage DirectiveTest Standard IEC/EN60598-1:2004

2004/108/EC EMC Directive-Exempt

This Test Report documents Regulatory Compliance Evaluations and Validation testing of the noted GYT San Diego, Inc,Model: Solar Guard Display St0443to validate CE Mark Compliance. This Evaluation and testing was conducted bySTORK Garwood Laboratories Inc, an independent, competent 3

rdparty Regulatory Compliance Testing Organization with

credentials appropriate for this task. It is the express opinion of Stork Garwood Laboratories Inc., that the noted GYTSan Diego, Inc, Model: Solar Guard Display St0443and their Appended Instructions are compliant and eligible to bear theCE Mark under a Declaration of Conformity.


2/21

Page 2 of 21

TECHNICAL FILEReport: GLIO 8590

Testing and Validation:Conducted by Stork Garwood Laboratories Inc.

Safety Standards, IEC/EN60598-1 2004 Safety of Luminaries

Solar Guard Display ST0443


3/21

Page 3 of 21

TTAABBLLEE OOFF CCOONNTTEENNTTSS

ITEM DESCRIPTION PAGE

EU Technical Construction File (TF) Report - Title Page 1

EU Technical File System Overview 2

Table of Contents 3Responsible Signatures & Document History 4

Testing Information & Client Information 5

EU Declaration of Conformity (DoC) - Document 6

Section 1.0 Summary of Product Qualifications to InternationalRequirements and the European Union (EU)

7

1.1 Statement of Organizational Charter - Competent 3rd Party 8

1.2 Declaration of Conformity Rationale 8

1.3 Purpose of the Declaration of Conformity (DoC) 91.4 Purpose of the Technical File (TF) 9

Section 2.0 Introduction to Qualifications 10

2.1 CE Marking Instructions 10

2.2 Validation of CE Mark Compliance 10

2.3 Calibration Details 10

Section 3.0 CE Mark Template 11

Section 4.0 Operation of Equipment Under Test (EUT) 12

4.1 Product Specification 12Section 5.0 Product Photos 13-17

Section 6.0 Product Testing 18

Section 7.0 Wiring Diagram 19

Section 8.0 Instructions 20-21


4/21

Page 4 of 21

RESPONSIBLE SIGNATURES

This report is intended for the use by the organization to which it is addressed, and willnot be made available to any other parties without the expressed written consent of theaforementioned organization. This report shall not be reproduced, except in full,without the written approval of Stork Garwood Laboratories, Inc.

WRITTEN BY: TESTED BY: VALIDATED BY:

Maria LumpkinTechnical Writer

Nick McMillanTest Technician

Chuck HeltonProduct Safety Director

DOCUMENT HISTORY

Revision Issue Date Description OfModifications

Revised ByReviewed

By

1September

2009Initial Release -------------------

ChuckHelton


5/21

Page 5 of 21

CLIENTINFORMATION

Quote Number GLIO 8590

Company Name

Address

City, State Zip

GYT San Diego, Inc

2498 Roll Dr. #826

San Diego, CA 92154

Contact Name Wilberth SantoyoGeneral Manager

STORKGARWOODINFORMATIONEMC Test Laboratory

AddressCity, State, Zip Code

PhoneFax

Web Site

STORK GARWOOD LABORATORIES, INC.143 Calle IglesiaSan Clemente, CA 92672 USA(949) 361-9189(949) 361-9597www.garwoodlabs.com

Contact NameTitle

E-Mail Address

Chuck HeltonDirector - Product Safety

[email protected] Name

TitleE-Mail Address

Don BennettLaboratory [email protected]

TESTINGINFORMATION

Test and TechnicalPersonnel

Maria Lumpkin, Technical WriterNick McMillan, Test TechnicianChuck Helton, Product Safety Director

Test Dates August 2009
http://www.garwoodlabs.com/mailto:[email protected]:[email protected]:[email protected]:[email protected]://www.garwoodlabs.com/


6/21

Page 6 of 21

European Union - Declaration of Conformity

GYT San Diego, IncFOR

Solar Guard Display St0443

Council Directives:2004/108/EC EMC Directive

2006/95/EC Low Voltage Directive

The Product cited above complies with the noted Safety of Luminaries Standards when installed and operated inaccordance with the Installation and Users Manual Provided. The product is declared to comply by Design, Testing and 3 rd

Party Evaluation. The Certification Program Management, Product Safety Testing and Evaluations were provided bySTORK Garwood Laboratories Inc which is located in San Clemente, CA, 92672, USA

EMC STANDARDS

EN 55015 RF Emissions and Immunity tests for LuminariesExempt-All components Passive- Switch and Incandescent Bulb

SAFETY STANDARD

EN 60598-1 2004 Safety of Luminaries

Importers Name: XXXXXXXXXXXXXXXXXXXXXImporters Address: Street Number Suite NumberEU City or Region: xxxBerParLonMadLisxxxEU Country & Postal Code: xxxBel Fr Sp UK 123xxx

Manufacturers Name: GYT San Diego, Inc

Manufacturers Address: 2498 Roll Dr.

City, State, Zip San Diego, CA 92155

Description of Equipment: Glass Film Display CaseModel Numbers Solar Guard Display St0443

Date of Manufacture: MM -YY

We the undersigned hereby declare that the equipment specified above conforms to the noted Directives and

Test Standards. Refer to the CE Mark Test Report, GLIO8590 including a Declaration of Conformity, CertificationDocuments and Test Results. The noted CE Mark Test report is available on request.

IMPORTER MANUFACTURER

Signature ____________________________ Signature _______________________________Typed Name___________________________ Typed Name _____________________________Title _________________________________ Title ___________________________________Date _________________________________ Date ___________________________________

This Declaration is Valid when information as to the identity of the Importer is filled in. The noted Equipment is verifiedto be compliant by Chuck Helton, Product Safety Director, STORK Garwood Laboratories Inc., San Clemente, CA 92672,

USA


7/21

Page 7 of 21

Section 1.0: Summary of Product Qualifications toInternational Requirements and the European Union (EU)

The equipment description and performance capabilities given in this section is

based on information provided by GYT San Diego Inc. "Note that someaspects of the performance claims were not verified by STORK GarwoodLaboratories, Inc., as those claims were not deemed Safety or Environmentallysignificant." This report documents the results of a series of RegulatoryCompliance Evaluations, EMC tests and Product Safety Tests performed onthe Solar Guard Display ST0443. The purpose of this series of evaluationsand tests was to demonstrate compliance of the equipment with the essentialrequirements of the EU Low Voltage Directive (LVD) 2006/95/EC.and the EMCDirective 2004/108/EC.

General Information

EU Directives2006/95/EC Low Voltage Directive2004/108/EC EMC Directive (Exempt)

Product Safety Standard IEC/EN60598-1 2004 Safety of Luminaries


8/21

Page 8 of 21

1.1 Statement of Organizational Charter - Competent 3rdParty

STORK Garwood Laboratories Inc. (GLI) is an Independent EMC and SafetyTesting Organization providing Regulatory Compliance Evaluations,Consultations and has Agent status with many Product Safety Agencies,Laboratories, Nationally Recognized Test Laboratories, the FederalCommunications Commission, OSHA and others. These Engineering andTechnical disciplines are offered to the public and private sector on a job-by-job contract basis. In accordance to the intent and definitions in the EuropeanUnions several Technical Directives, STORK Garwood Laboratories Inc.(SGLI) and its selected affiliates are entitled to be designated as a Competent3rd Party.

SGLI has no organizational or financial relationship with any company,

institution or private individual and strives to render sound engineeringevaluations and decisions within the areas of expertise, not influenced byspecial interests.

The opinions and suggestions rendered are, in our best judgment, true andreliable. It is the responsibility of the client to determine suitability of opinionsand suggestions presented. If information provided is used for productchanges or upgrades, the client assumes all liabilities.

1.2 Declaration of Conformity - Rationale

This Report contains a Declaration of Conformity (D.o.C). This D.O.C. is basedon testing of the Essential Elements of Safety, Client Provided PerformanceSpecifications and Detailed Engineering Evaluations. The essentialrequirements of the EU Low Voltage Directive have been met and in theopinion the test engineers the Solar Guard Display ST0443 is compliant. Itmust be noted that assumes responsibility for all aspects of continuedcompliance and the claims made on each D.o.C. GYT San Diego, Inc. mustalso have a Quality Assurance Program established and assumesresponsibility for a Quality Assurance Program suitable for CE Compliance

This TF Report contains a sample D.o.C that may serve as a pattern and becopied by GYT San Diego, Inc. as needed, to provide one with each shipment

to destinations in the EU or to EU candidate countries.


9/21

Page 9 of 21

1.3 Purpose of the Declaration of Conformity

According to the established rules, a Declaration of Conformity (D.o.C.) is toaccompany each shipment. Its purpose is to formally notify the Customs

Officials at any EU Port of Entry, by a Legal Declaration, that the CE MarkedProducts in the shipment are compliant to the cited EU Directives. It is requiredto:

v Identify the product(s) by Type and Model Designation andprovide the month/year of manufacture.

v Identify the Directives and Standards that the product complieswith.

v Identify the Manufacturer by name and address.v Identify the Importer/Agent by name and address (Must be in

EU).v Establish Product Responsibility. It is a Mutual signed and dated

Declaration by the Manufacturer and Importer/Agent declaring

that the product is compliant.

1.4 Purpose of a Technical File

The Technical File (TF) is a detailed report that provides the technicaldescription of the products and the associated test and evaluation criteria. Itadds backup and credibility to the CE MARK and Declaration of Conformity.It technically describes the products, states their rated capabilities and definesthe technical standards that are applicable. It further provides the evaluationand test results and on certain products, risk assessments related to safety tothe installers, maintenance personnel and users of the product.

A TF is not usually provided with a product shipment. A hard copy and anelectronic copy are typically held in a safe place by the manufacturer and acopy provided to all Dealers and Importers in the EU. The TF is used to setaside any challenges to the validity of the CE Mark. It shows a high level ofDue Diligence by the Manufacturer and Importer/Agent. It is a detailedvalidation, by a competent Independent 3rd Party, that the products arecompliant and thus eligible to display the CE Mark. The TF is provided in PDFformat so that it may be readily transmitted as an e-mail attachment.


10/21

Page 10 of 21

SSEECCTTIIOONN 22..00:: IINNTTRROODDUUCCTTIIOONN TTOO QQUUAALLIIFFIICCAATTIIOONNSS

This report documents the results of a series of product safety measurementsand tests performed on the. The purpose of said tests was to demonstratecompliance of the test samples, and their respective families, with therequirements of the EU Council Low Voltage Directive 2006/95/EC andapplicable test standards, as noted herein.

All product safety, electrical evaluations and testing was performed at theSTORK Garwood Laboratories, Inc. facility in San Clemente, CA. To reiterate,all testing was conducted using calibrated test Instruments and test set-upssuitable for validation of CE Mark compliance of the Solar Guard DisplayST0443. Additionally, all tests were performed under controlled laboratoryconditions by STORK Garwood Laboratories, Inc.

2.1 CE Marking Instructions

The Model referenced above and its major components need to bear a largeprominent CE Mark on the overall package, if palletized. The concept is toconvey to customs inspectors, that the product within the packaging is CEMARK compliant. The CE MARK should also be applied to the product labels.The CE Marks should be of sizes that are readily visible to the unaided eye.The basic CE MARK Artwork has been provided as a jpeg image in thisdocument. Finally, a completed Declaration of Conformity, per the sampleprovided, must also accompany each shipment.

2.2 Validation of CE Mark Compliance

Based on an investigation of the GYT San Diego, Inc. Solar Guard DisplayST0443 it is in the opinion of STORK Garwood Laboratories, Inc., compliantwhen provided with installation and user instructions involving local languages,and are eligible to bear the CE Mark. As such, the noted Solar Guard DisplayST0443 is entitled to have free access to the available markets and to passthrough all EU Ports-of-Entry.

2.3 Calibration Details

All test equipment used for this program is checked prior to testing to insure

up-to-date calibration and confirm that parameters being measured areappropriate for the range of measuring instruments, respectively. Calibration ischecked on a routine basis using standards traceable to the National Instituteof Standards and Technology (NIST). Calibration of equipment is performed inaccordance with the STORK Garwood Laboratories, Inc. quality program andsatisfies the requirements of the previously referenced standards.


11/21

Page 11 of 21

SECTION 3.0: CE MARKING


12/21

Page 12 of 21

SECTION 4.0: OPERATION OF EQUIPMENT UNDER TEST

Testing was conducted using nominal input voltages and frequencies

standardized by the 28 countries that make up the European Union. This is230VAC, 1 , 50Hz, protected at the 10A level.The Safety Testing was conducted at STORK Garwood Laboratories, Inc. inSan Clemente, CA, USA.

4.1 Product Description

The Equipment Manufacture, GYT San Diego, Inc. has designed and isproducing the Solar Guard Display ST0443 which is hereafter designated asthe product. The Product function is to assist a sales presentation for Windowtinting films. The Products operational feature is an incandescent electric

Luminaire that is configured as Parabolic Reflector (PAR) with a specialcoating that produces projected infrared radiation.The PAR lamp is mounted via an Edison Screw Base Socket mounted to abracket with its centerline horizontal. This is surrounded by an open cubicaluminum frame mounted on a turntable. The aluminum frame hasaccommodations for inserting up to 4 glass slides vertically with various heatblocking films.The turntable allows the frame to be conveniently rotated so a glass slide/filmcombination can be positioned in the projected IR path of the PAR IRLuminaire.The effectiveness of various films can be judged by the degree of heat that canbe felt by a persons hand in front of any particular glass/film.

The base of the product houses the AC Inlet which is an IEC 60320, C8.The C8 Inlet will accept any International or Domestic AC Power Cord with aC7 plug.As the PAR Luminaire is rated for 120V operation a 2:1 Step-down isolationtransformer is provided to reduce the EU Standard 230 Volts to the 115-120Vrange.A clockwork spring motor timer with an electric switch is provided to energizethe Luminaire and limit the time the Luminaire is on. By rotating the WhiteKnob clockwise to a desired time in minutes the Luminaire is energized. Onrelease of the White Knob the timer allows the time out to begin and theLuminaire will turn off when the preset time has expired.


13/21

Page 13 of 21

5.0 Photos of Solar Guard Display ST0443

Front View of Product

To

Top View

Thermal

Ventilation Slots

Slot for GlassSlide/FilmFour Places

Rotary Turn Table

PAR I/R Luminaire

Aluminum Frame

Luminaire Timer

Switch

Polymer LaminateBase

Shows Quadpattern ThermalVentilation Slots


14/21

Page 14 of 21


Bottom View

Internal View Showing Luminaire

Base Plateattached by Stars

Screws

Edison ScrewBase Socket

Clamp Bracket

Riser tube

serves asconduct for ACCord

PAR I/R Lamp


15/21

Page 15 of 21


Internal Bottom View with Cover removed

Transformer DiagramConverts 230V AC to 115V AC

Step-downTransformer

Backside of IEC60320 Type 8 ACSocket

Timer Switch


16/21

Page 16 of 21


Transformer Certification Label

Transformer Warning Label


17/21

Page 17 of 21


Rear View of Clock Works Timer


18/21

Page 18 of 21

6.0 Testing of Solar Guard Display ST0443

Input Testing

Leakage Current


19/21

Page 19 of 21

7.0 Wiring Diagram of Solar Guard Display ST0443


20/21

Page 20 of 21

8.0 Display Instruction of Solar Guard Display ST0443


21/21

8.0 Display Instruction of Solar Guard Display ST0443

Date post:	04-Apr-2018
Category:	Documents
Upload:	reilaudio1
View:	215 times
Download:	0 times