Halfen Mt Fbc Us

8/21/2019 Halfen Mt Fbc Us

1/68

HALFEN MOUNTING CHANNELS AND ACCESSORIES

FRAMING SYSTEMS

MT-FBC 10-US


2/682 2012 HALFEN MT-FBC 10-US www.halfenusa.com2

y z

e2e1

yx z

FR

FL FQ

FSZ

HALFEN FRAMING AND MOUNTING SYSTEMS

Contents

HALFEN Mounting Channels, HALFEN T-bolts

- Introduction- Product range - overview: Framing and Mounting channels

- Load symbols and definitions

- Heavy duty components

- Medium duty components

- Light duty components

38

10

12

27

36

HALFEN Mounting System Accessories

- Threaded rods, hexagonal headed bolts, nuts, washers

- Channel end caps, channel cover strips

- Cantilevers

Materials, design properties, constructions

- Materials and finishes

- Channel profiles: detailed properties at a glance

- T-bolts: product range at a glance

- Welding seam sizing and bearing capacity values

- HALFEN Mounting channels as compression elements

- Calculation of bolt lengths

- T-Bolt pretension forces

44

46

47

48

50

54

56

58

59

61

Appendix:

HALFEN Framing Channels in mechanical engineering and machine building

- Specification texts

- Index

- Addresses/contact

- Static and dynamic tension tests

66

67

68

60

Fotolia

NEW!


3/68 3 2012 HALFEN MT-FBC 10-US www.halfenusa.com 3

Adjustable HALFEN channel mounting systems offer a whole range of benefits:

The adjustable HALFEN channel-boltsystem is an assembly and mounting

system

Full flexibility in positioning and

dimensioning of the bolt connections

Choice of corrosion protection:

- Pre-galvanized channels

for low demands

- Hot-dip galvanized channels for

high demands

- Channels in stainless steel for high-

performance requirements

Quick assembly and adjustment of

equipment and structural components

With HALFEN mounting channels you avoid:

Time consuming planning of

inflexible bolted fixings

Costly manufacturing of bolt fixings

Costly corrosion protection work


Introduct ion

Quality is an outstanding feature of

our products. HALFEN materials and

products are subject to stringent quality

controls.

Quality

HALFEN cast-in channels

Certificate-no. QS-281 HH

A quality audit by Germanischer

Lloyd Certification GmbH confirmed

that our quality management

system meet the demands of the

ISO 9001:2008 standard.

All hot rolled HALFEN profiles and some

of the light framing channels are also

available as HTA/HZA HALFEN cast-in

channels for embedment into concrete.

Both versions use the same T-bolts and

locking plates.

You can find more information on

HALFEN channels in our catalogue;

"HALFEN Cast-in channels

Product Information, BP"

when upgrading already completed

structural components i.e. when

adjusting components in service

Change or up-date entire projects

with standard tools

No specialist required to carry out

modifications on-site

Dust free and low noise levels when

modification work is done on-site

Corrosion protection is not

compromised by bolting

A large selection of standard chan-

nels with good load bearing charac-

teristics. All the loads stated in this

catalogue are permissible loads



Mount ing channels HM, HL, HZM and HZL


Mounting channels

The hot rolling process makes these channels ideally suited to:

heavy loads

dynamic loads

connections requiring very high torque

welding

Cold-rolled channels

Channels are available with holes (ladderbacked) or without holes (plain).

Hot rolled channels

Smooth channels HM

Very high tensile loads of

up to 7.0 Kips (31 kN) are possible

High longitudinal loads of up to

1.7 Kips (7.5 kN) are possible using

nibbed T-bolts (carbon steel channels)

Cold-rolled channels HL, HM

For lower loads in longitudinal

channel direction

Economic due to large selection ofchannels

Toothed channels HZM

Toothed profile mechanically interlocks

with toothed bolt to allow high longi-

tudinal loads of up to 4.9 Kips (22 kN)

3 channel sizes for maximum

efficiency

Toothed channels HZL, HZM

For high loads in longitudinal channel

direction

Non-slip connection for high channel

loads Cantilever fixing on a vertical conveyor system

Welding jig, used in locomotive construction

Roller bearing fixing of a cableway



H4.6HALFEN8.8

H4.6HALFEN4.6H4.6HALFENA4-50

H4.6HALFENA4-70

H 4.64.6

H 4.68.8

HSR All TypesHZS 29/20HZS 38/23HZS 53/34

HS All Types

HZS 41/22

HZS 41/41

H 4.6H4.6HALFEN4.6

Manufacturer

strengthgrade or material grade

(for individual dimensions)

HALFEN T-bol ts HS, HSR and HZS


HALFEN T-bolts

Type HS Type HSR Type HZS

HALFEN T-bolts; plain

Suitable for all channels

Load bearing capacity

in two directions

Marked at shank end

with one notch

HALFEN T-bolts with nibs

Only suitable for use in hot-rolled

channels from the heavy duty

system

Nibbed; therefore non-slip,

load bearing in all directions

The hook-head bolt prevents

turning under vibration

Marked at shank end with two

notches (applies only to steel)

Toothed HALFEN T-bolts

For toothed channels

HZM and HZL

Toothing also provides positive

load bearing transmission in

longitudinal channel direction.

The risk of slipping is eliminated

Marked at shank end with two

notches

Ident i fy ing HALFEN T-bol ts

Marking at the shank end of the HALFEN T-bolts: After assembly check the correct orientation of the marking on the shank end

of the T-bolts. The notch or notches must be at right angles to the channel length.

Location of

nib on bolt

Teeth in

channel

Strength class 4.6

electroplated or

hot-dip galvanized

Strength class 8.8

electroplated or

hot-dip galvanized

material grade A4 - 50

stainless steel

(Type 316, grade 50)

material grade A4 - 70

stainless steel

(Type 316, grade 70)

Notches on the shank tip:

Bolt identification on the bolt head



Locking plate GWP

Order examples

Locking plates with grip (see Me-

dium duty Framing system page 35).

The toothing grips the channel lips.

Locking plates with spring are used in

particular for securing plates or panels.

(see Medium duty Framing system

page 35).

Locking plates (channel nuts) allow

any metric bolt or threaded rod to be

used. Locking plates for UNC threads

are available.

or use the 12-digit item number e.g. 0280.200-00003 or use the 12-digit item number e.g. 0350.090-00068


Locking p lates

Item description for channels Item description for T-bolts

Type

Material

Thread

Length (mm)

HS 50/30 M20x100 GV-S

TypeMaterial

Length (mm)

HM 50/30 FV 6070

If you have any further questions:

Our technical department and our field support technicians

will gladly advise and support you in resolving questions

concerning HALFEN assembly systems.

HALFEN Engineering Support

Tel.: 1 800 323 6896

E-Mail: [email protected]

www.halfenusa.com



Whether for low or veryhigh loads: you willalways find a cost effective

solution for your requirements

in the HALFEN range of

channels and T-bolts

Versatile and adaptable

Adjustable assembly

All connections can be adjusted at

any time; they are easily replaced

or extended

Almost unlimited in its range of

application;

e.g. Building construction,

industrial construction,

steel construction,engineering construction,

vehicle manufacturing

and many other sectors

Heavy duty mounting system

The heavy duty channels

are predominantly hot-rolled and

particularly suitable for heavy loads

Medium duty framing system

All medium duty framing and

mounting channels have the same

profile width and are compatiblewith the innovative HALFEN

Powerclick assembly system

Light duty mounting system

The light duty channel is the perfect

mounting solution for low loads

Mounting ChannelsThe advantages at a glance

Secure and reliable

Corrosion protection remainsintact after bolting

Large selection of standard chan-

nels with very good load bearing

capacities

Toothed channels for non-slip

connections



Heavy duty system

Hot-rolled Cold-rolled

HM 72/48 HM 52/34 HM 50/30 HM 49/30 HM 50/40, HL 50/40 HM 486

30

HS 72/48, HSR 72/48,GWP 72/48

HS 50/30, HSR 50/30,GWP 50/30

Medium duty system

Cold-rolled Cold-rolled, toothed Cold-rolled Cold-rolled, toothed

HM 41/41, HL 41/41 HZM 41/41, HZL 41/41 HM 41/62, HL 41/62 HM 41/83, HL 41/83 HM 41/22, HL 41/22 HZM 41/22, HZL 41/22

HZS/HS 41/41, HZS 41/22GWP 41/41, GWP 41/22

Light duty system

Cold-rolled

HM 36/36, HL 36/36 HM 38/17 HM 28/28, HL 28/28 HM 26/26, HL 26/26 HM 28/15, HL 28/15 HM 315

HS 38/17,GWP 38/17

HS 28/15,GWP 28/15

GWP 28/15


Product range overview: Channels + HALFEN T -bolts

Page 12 Page 14 Page 15 Page 15 Page 16 Page 16

Page 32 Page 31

Page 40

Page 29 Page 30

Page 40 Page 39 Page 38

Page 28

Page 36

Page 27

Page 36

2 7/8"

1 5/8" 1 5/8"

1 5/8"1 5/8"

1 5/8" 1 5/8"

2 1/16" 2" 2"

1 7/8"

1 5/8" 1 5/8" 2 7/16" 3 1/4" 13/16" 13/16"

1 5/16" 1 3/16" 1 3/16"1 9/16" 1 1/16"

1 15/16"1 7/8"

1 5/16"

7/8" 7/8"

7/8" 7/8"

7/8" 7/8"

7/8" 7/8" 7/8"7/8" 7/8"

1 7/16"

1 1/2"1 1/16" 1"

11

/8

" 13

/16

"1 7/16" 11/16" 1 1/8" 1" 5/8" 5/8"

11/16"

11/16" 1/2" 1/2"1/2" 5/8"



Hot-rolled Cold-rolled Hot-rolled, toothed Cold-rolled, toothed

HM 40/22 HM 40/25 HM 422 HZM 53/34 HZM 38/23 HZM 29/20 HZL 63/63

25

40

18 2234

53

HS 40/22, HSR 40/22,GWP 40/22

HZS 53/34HZS/HS 38/23,HS 38/17,GWP 38/17

HZS/HS 29/20,HS 28/15,GWP 28/15

HZS 41/22,HZA/HS 41/41,HZS 41/22,GWP 41/41

Cold-rolled

HLL 41/41 HLL 41/22

Cold-rolled

HM 20/12, HL 20/12

HS 20/12,GWP 20/12


Product range overview: Channels + HALFEN T -bolts

Page 18 Page 18 Page 18 Page 22 Page 20 Page 24 Page 26

Page 33 Page 33

Page 42

hot-dip galvanized FV or mill finish WB

pre-galvanized SV

stainless steel A4 (comparable to 316)

stainless steel A2 (comparable to 304)

stainless steel HCR

HZM/HZL toothed profiles

Material; finishes:

For further information on materials

and finishes see page 48

NEW!

1 9/16"

7/8"11/16"

1 9/16" 1 9/16" 2 1/16"1 1/2" 1 1/8"

2 1/2"

1" 7/8 " 1 5/16"7/8 " 3/4 " 2 1/2"11/16"

11/16"7/8" 11/16"

9/16"

7/8"

1 5/8"

1 5/8"

1 5/8" 13/16"

7/8"

7/8"

3

/4"1/2"3/8"



Symbols used for the building industry and their definition

HALFENT-headBolts

FS

Permissible load per T-boltLoad in tension and transverse load directions.T-bolts HS and smooth channels HM.

FS

Permissible load per T-boltLoad in tension, transverse and longitudinal directions.T-bolts HS and HSRwith smooth channels HM. T-bolts HZS with toothed channels HZM and HZL.

FSx Permissible load per T-bolt in longitudinal channel directionFriction coefficient thread/bearing surface =0.14; tightening factor 1.6; safety factor 3

Framingchannels

Fz

Maximum point-load capacity - centric loadThe load carrying capacity of the channel lips is decisive.Load figures are only valid for continuously welded channels, or intermittent welds according to the table on page 56.In all other cases suitability of the welding seam must be checked.

Fflex

Bending load capacity with L spanPermissible channel (as a single span element) bending load capacity depends on span distance.Limitation of the load capacity determined by bending tension and/or defined deflection.

qflex Bending load capacity with L spanPermissible line load of the channel (as a single span element) depends on span distance.Limitation of the loading capacity determined by bending tension and/or defined deflection.

Fx

Permissible load in longitudinal channel direction

Fy

Carrying capacity of the channels under transverse load angle < 60Permissible load at a defined angle to the channel, welded or bolted to support.

Fz

Carrying capacity of the channels under transverse load angle 60

Permissible load at a defined load angle to the channel, welded or bolted to support.

FK

Permissible buckling load compression rodPermissible buckling load.

M Permissible bending moment of the channel lipOnly applies to channels welded to support otherwise torsion must be taken into account.

M

FK

L

Fz

L

Fflex

L

qflex

L

Fz

Fy

Fy

Fx

Fs

Fsx

Fs


Load symbols and def in i t ions

F = (Fy + F

z)

F = (Fy + Fz)

The HALFEN adjustable assembly systems can be used in a wide range of fields. It is therefore important that the codes, guidelines and

design criteria applicable to each field are considered. The technical values and data for framing channels and T-bolts for use in the building,

mechanical engineering and steel construction industries are explained in the respective sections below.



Symbols used for mechanical engineering steel construction industry and their definitions

HALFENT-bolts

Fv

Bolt pretension force

The bolt is pretensioned by torquing, and is calculated according to VDI 2230 guidelines

FR

Resulting forceThe resulting force F

Ris the vector addition of the external loads F

Lin the longitudinal channel direction and the external load FQ

transverse to the longitudinal channel direction; the resulting force is transferred frictionally to the channel.

FSZ

Force in the longitudinal bolt directionThe force F

SZworks as an external load along the screw longitudinal axis and perpendicular to the channel surface and is transfer-

red frictionally to the channel.

Framingchannels

Fz Maximum Point load-carrying capacity centric loadThe load carrying capacity of the channel lips is decisive.Load figures are only valid for continuous welded channels or intermittent welds according to the table on page 56.In all other cases suitability of the welding seam must be checked.

Fy

Load capacity of the channels under transverse load angle< 60Permissible load for a defined angle to the welded or bolted channels.

Fz

Load capacity of the channels under transverse load angle 60Permissible load for a defined load angle to the welded or bolted channels.

Fz

Fy

Fy

Fz

L

Fv

FL

FQ

FR

FSZ


Load symbols and def in i t ions

FR= (F

L + F

Q)

For further technical information and load tables applicable for mechanical engineering see pages 6065.

When designing an adjustable assembly system the external load Fimust be less than or equal to the minimum permissible load of the

T-bolt Fs and to the maximum point load capacity and respectively to the bending load capacity of the HALFEN framing channel Fz.

Fi MIN (Fs; Fz) ( see page 50)

All load figures are permissible loads.

Design load i.e. stress calculation: FR,d

= 1.4 F (forces)

Design load i.e. stress calculation: MR,d

= 1.4 M (moments)

The force Fszalong the screw longitudinal axis must be less than or equal to the maximum point load capacity of the framing channel

The force FQtransverse to the longitudinal channel direction must be less than or equal to the load capacity transverse to the

longitudinal channel direction of the framing channel Fy.

FQ F

y

Fsz F

Z

NEW!



Dimensions and load capacities HM 72/48

Material Order-no.0280.

Length Channel-weight

Channel-cross-section

Moment of inertia Moment of resistance Max. point-loadbearing capacity

Bending load capacity for spanL [in]

G A Iy

Iz

Wy

Wz

Fz

19.7 in 39.4 in 59.1 in

[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] Fflex

[kips]

WB 180-00002

239 5.94 1.747 0.840 2.001 0.889 1.411 6.97 12" 5.01 2.52 1.66FV 180-00003A4 180-00001

Fz= maximum bending load capacity on the channel lips

HM72

/48

y z

y

x z

y z

y

x z

72

33

54.5

48.5

15.5

Fflex

L

Fz

L


Heavy duty mount ing channels

Double channel

on request

Scale 1:1

Channels HM 72/48

Accessories

VUS 72/49 washer

see page 45

HM 72/48 hot-rolled

For further channel data and static

properties see page 50

2.835"

1.299"

0.197" 0.1

77"

1.9

09"

0.6

10"



Load capacity

Permissible load Thread Load capacity [kips]

M 12 2.09

M 16 3.89

M 20 4.95

Dimensions HS 72/48 and HSR 72/48

Length l[in]

HS 72/48 HSR 72/48

M 20 M 24 M 27 M 30 M20

2" FV FV

A4-50

2" FV 8.8

3" FV FV FV FV FV 8.8

GV 8.8 FV 8.8

4" FV FV FV FV

GV 8.8 GV 8.8 FV 8.8

A4-50

6" FV FV FV

GV 8.88" FV FV FV

Dimensions

GV

Thread

A4

Thread

a

[in]

b

[in]

d

[in]

M 12 M 12

2.44 1.22 0.87M 16 M 16

M 20 M 20

Permissible loads for T-bolts

for standard steel profiles for stainless steel

permissible loadper T-bolt

recomm. load per T-bolt in longitudinal channel directionpermissible load

per T-boltrecomm. load per T-bolt

in longitudinal channel direction

Grade Grade HS, Grade 4.6 HS, Grade 8.8 HSR, Grade 8.8

HS, GradeA4 - 50[kips]


Tighteningtorque[lb.ft]

Thread size

4.6[kips]

8.8[kips]

[kips]

Tighteningtorque[lb.ft] [kips]


(= 3)[kips]


M 20 6.07 12.68 0.31 89 1.06 295 1.69 295 - - -

M 24 8.72 18.25 0.45 148 1.53 502 - - 8.72 0.45 148

M 27 11.35 23.83 0.58 221 2.00 738 - - - - -

M 30 13.87 29.00 0.72 295 2.45 1033 - - - - -

Note: do not exceed max. channel load bearing capacity; see page 12

Fsx FsxFs Fs

ab

d


T-bolts and accessor ies

HS 72/48

T-bolt

incl. nut

HSR 72/48

T-bolt with nib

incl. nut

HALFEN T-bolts HS 72/48 and HSR 72/48

Locking plates

Locking plate GWP 72/48

2.283"2.283"



Dimensions and load bearing capacities HM 52/34


length Channelweight

Channelcross-

section


Bending load capacity for span L [in]

G A Iy

Iz

Wy

Wz

Fz

19.7 in 39.4 in 59.1 in


[kips]

WB 190-00002

239 3.35 0.983 0.224 0.569 0.326 0.551 3.82 8 " 1.98 0.99 0.63FV 190-00003

A4 190-00001


y z

yx z

y z

yx z

52.5

22.5

4.1

4

33.5

10.5

Fflex

L

Fz

L

see page 46 see page 46

HPE 52/34 Channel end cap PA - 22 Channel cover



Double channel

on request

Channels HM 52/34



Accessories

VUS 52/34 Washer

see page 45

HM 52/34 hot-rolled

Scale 1:1

T-bolts see page 17

2.067"

0.161"

0.886"

1.3

19"

0.1

57"

0.4

13"



Dimensions and load bearing capacities HM 50/30 and HM 49/30


Length Channel-weight

Channelcross-

section



G A Iy

Iz

Wy

Wz

Fz

19.7 in 37.4 in 59.1 in


[kips]

HM 50/30

239 2.17 0.639 0.124 0.336 0.198 0.346 2.47 7" 1.19 0.61 0.36WB 200-00002

FV 200-00003

A4 200-00001HM 49/30

239 1.94 0.569 0.100 0.317 0.144 0.323 1.10 18" 0.97 0.49 0.27

WB 220-00001

FV 220-00002

A2 220-00003

A4 220-00004

Fz= maximum bending load capacity on the channel lips HCRversion on request

y z

yx z

y z

yx z

2.75

22.5

7.8

5

49

33

7.4

Fflex

L

Fz

L

see page 46

PA - 41 Channel cover



Channels HM 50/30 and HM 49/30



Accessories

VUS 52/34 Washer

see page 45

HM 50/30 hot-rolled HM 49/30 cold-rolled

SIC 50/30 Locking plate

Scale 1:1

see page 45

T-bolts see page 17

Double channel

on request

1.969"1.929"

0.866"

0.118"

0.2

91"

1.1

81"

0.886"

0.118"

0.108"

1.1

81"

0.3

09"



Dimensions and load bearing capacities HM 50/40, HL 50/40 and HM 486

Material Order-no.

Length Profileweight

Channelcross-

section



G A Iy

Iz

Wy

Wz

Fz

19.7 in 39.4 in 59.1 in


[kips]

HM 50/40 0280.

236 2.25 0.662 0.208 0.372 0.242 0.386 1.21 24" 1.53 0.76 0.52WB 090-00002

FV 090-00003

A4 090-00001

HL 50/40 0281.

236 2.12 0.578 0.171 0.369 0.223 0.383 1.21 20" 1.28 0.65 0.43WB 100-00001

FV 100-00002

A4 100-00003

HM 486 0280.

236 1.55 0.457 0.071 0.231 0.117 0.245 0.787 18" 0.74 0.38 0.20WB 100-00001

FV 100-00002


y z

yx z

y z

yx z

18

40

60

HL50

/40

HM50

/40

48

27

22

6

2.5

HM48

6

49

39

3

22

7

Fflex

L

Fz

L



Channels HM 50/40, HL 50/40 and HM 486

Accessories


properties see pages 50, 52

HM and HL 50/40 cold-rolled HM 486 cold-rolled


Scale 1:1

T-bolts see page 17 see page 46 see page 46

0.866"

0.118"

1.929"

1.890"

2.362"

1.575"

0.709"

0.866"

0.098"

0.27

4"

1.5

35"

1.063"

0.236"



Load capacity [kips]

Permissible load Thread GWP 50/30 GWP 50/40

M 6 0.49

M 8 0.90 0.90

M 10 1.44 1.44

M 12 2.09 1.44

M 16 2.09 1.44

Permissible loads for HALFEN T-bolts

for standard steel profiles for stainless steel profiles



per T-boltrecomm. load per T-bolt






Thread size

4.6[kips]

8.8[kips]

[kips]



(= 3)[kips]


M 10 1.44 2.99 0.07 11 0.25 35 - - 1.44 0.07 11

M 12 2.09 4.36 0.11 18 0.43 52 - - 2.09 0.11 18

M 16 3.89 8.11 0.20 44 0.67 148 1.12 148 3.89 0.20 44

M 20 6.07 12.68 0.31 89 1.06 295 1.69 295 6.07 0.31 89


Dimensions HS 50/30

Length l[in ]

Length l[in]M 10 M 12 M 16 M 20 M 10 M 12 M 16 M 20

1 1/4 " GV GV GV 2 1/2 " GV FV A4-50 A4-50 3 " GV

1 3/8 " GV A4-501 1/2 " GV GV GV/GV8.8 3 1/4 " GV/GV8.8 GV/GV8.8 GV8.8

FV FV A4-50 A4-50 A4-50

3 1/4 "Li A4-501 3/4 " GV8.8 GV/GV8.8

A4-50 4 " GV GV/GV8.8 GV/GV8.82 " GV GV GV A4-50 FV FV

A4-50 FV A4-50A4-50 5 " GV GV GV

A4-502 3/16" GV 6 " GV GV GV/GV8.8

FV FV A4-50A4-50 A4-50

2 3/8 " GV/GV8.8 GV/GV8.8 GV8.8 8 " GV GV GVA4-50 12 " GV GV

High corrosion resistance stainless steel T-bolts HS 50/30. Material order grade HCR, available on request.

Dimensions HSR 50/30

Length l[in]

Length l[in]M 10 M 12 M 16 M 20 M 10 M 12 M 16 M 20

1 1/2 " FV8.8 2 3/8 " GV8.8 GV8.8

1 3/4 " GV8.8 3 " GV8.8

Fsx FsxFs Fs


HALFEN T-bolts and accessor ies

HS 50/30

HALFEN T-bolt

incl. nut

HSR 50/30

HALFEN T-bolt

with nib

incl. nut


Locking plates

0.827"1.712"

0.472"

0.787"1.654"

0.315"

Locking plate

GWP 50/40

Locking plate

GWP 50/30

Li = left hand thread

1.614"

1.614"



Dimensions and load bearing capacities HM 422 (C40)

Mat. Order-no.0280.

Length Channelweight

Channelcross-

section

Moment ofinertia

Moment ofresistance

Max. point-loadbearing capacity

Bending load capacity forspan L [in]

G A Iy

Iz

Wy

Wz

Fz

19.7 in 39.4in 59.1 in


[kips]

WB 110-00001236 1.04 0.307 0.031 0.103 0.063 0.132 0.56 14.17 0.41 0.20 0.09

FV 110-00002F

z= maximum bending load capacity on the channel lips

y z

yx z

y z

yx z

Dimensions and load bearing capacities HM 40/22 and HM 40/25


Length Profile-weight

Channelcross-

section



G A Iy

Iz

Wy

Wz

Fz

19.7 in 39.4 in 59.1 in


[kips]

HM 40/22

239 1.41 0.415 0.047 0.141 0.099 0.163 1.28 8" 0.58 0.29 0.13WB 210-00002

FV 210-00003

A4 210-00001

HM 40/25

239 1.41 0.412 0.049 0.146 0.085 0.186 0.85 13" 0.58 0.29 0.13

WB 230-00001

FV 230-00002

A2 230-00003

A4 230-00004


y z

yx z

y z

yx z

.

2.4 2.

4 2.75

5.6

HM40

/22

Fflex

L

Fflex

L

Fz

L

Fz

L



Channels HM 40/22, HM 40/25 and HM 422

Accessories

HM 40/22 hot-rolled HM 40/25 cold-rolled

HM 422 (C40) cold-rolled

VUS 40/25

Washer

SIC 40/22

Locking plate


Scale 1:1

Scale 1:1

Double channel

on request

39.5

21.

5

1.575"

0.709"

0.220"

0.108"0.709"0.094"

0.236"

0.9

06"

0.0

94"

0.9

84"

1.555"

1.555"

0.709"

0.236"

0.079"

0.8

46"



Dimensions HS 40/22

Length l M 10 M 12 M 16 Length l M 10 M 12 M 16

[in] Material Material Material [in] Material Material Material

3/4 " GV GV 3 1/4 " GV GV GV

1 1/4 " GV GV GV A4-50 A4-50

FV 3 1/4 "Li A4-50 A4-50

A4-70 A4-50 A4-50 4" GV GV GV

1 1/4 " GV GV GV FV

A4-70 A4-50 A4-50 A4-50 A4-50

1 3/4 " GV

2 " GV GV GV 5" GV GV

FV FV 6" GV GV

A4-70 A4-50 A4-50 A4-50 A4-50

2" Li A4-50 8 " GV GV2 3/8 " GV GV GV A4-50

A4-50 10 " GV

12 " GV



M 6 0.49

M 8 0.90

M 10 1.44

M 12 2.09

Dimensions

GV

Thread

A4

Thread

a

[in]

b

[in]

d

[in]

M 6

1.378 0.6690.394M 8 M 8

M 10 M 10

M 12 M 12 0.453

Dimensions HSR 40/22

Length l[in]

M 16 Length l[in]

M 16

Material Material

1 1/2 " GV 8.8 2 3/8 " GV 8.8





per T-boltrecomm. load per T-bolt-





Tighteningtorque[lb.ft]Thread

4.6[kips]

8.8[kips]

[kips]



(= 3)[kips]


M 10 1.44 2.99 0.07 11 0.25 35 - - 1.44 0.07 11

M 12 2.09 4.36 0.11 18 0.36 52 - - 2.09 0.11 18

M 16 3.90 8.11 0.20 44 0.67 148 1.12 148 3.89 0.20 44


Fsx FsxFs Fs

32.5

32.5

Li = left hand thread




Locking plate

HS 40/22

HALFEN T-bolt

incl. nut

HSR 40/22

HALFEN T-bolt

with nib

incl. nut

locking plate GWP 40/22

1.280"

1.280"



Dimensions and load bearing capacities HZM 53/34



Channelcross-

section



G A Iy Iz Wy Wz Fz 19.7 in 39.4 in 59.1 in[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] F

flex[kips]

WB 070-00002

239 3.11 0.916 0.222 0.558 0.306 0.540 4.95 9 " 2.81 1.39 0.63FV 070-00003

A4 070-00001


52.5

22.5

4

4

34

Fflex

L

Fz

L



y z

yx z

y z

yx z

Scale 1:1

Channel HZM 53/34

Accessories

HZM 53/34 hot-rolled, toothed


properties - see page 50

see page 46

PA - 22 Channel cover VUS 52/34 Washer

see page 45

NEW!

2.067"

0.886"

0.157"

1.3

39"0

.157"



Dimensions HZS 53/34

Length l M 16 M 20

[in] Material Material

2 3/8 " GV8.8

A4-70

2 1/2 " GV8.8

A4-70

4 " GV8.8 GV8.8

A4-70 A4-70


for standard steel profiles for stainless steel profilesfor stainless orstandard steelprofiles

permissible load per HALFEN T-bolt permissible load per T-bolt

Tightening torque[lb.ft]

HZSGrade A4-70

[kips]longitudinal load F

sx

[kips]Thread

Tightening torque[lb.ft]

HZSGrade 8.8

[kips]

M 16 148 8.11 148 5.314.3

M 20 258 12.68 258 8.27

Note: do not exceed max. channel load bearing capacity; see pages 20, 56

1.64

l

FsFs

Fsx



NEW!

HZS 53/34

HALFEN T-head

bolt, toothed

incl. nut

HALFEN T-bolts toothed HZS 53/34

1.638

"



Dimensions and load bearing capacities HZM 38/23



Channelcross-

section



G A Iy

Iz

Wy

Wz

Fz

19.7 in 39.4 in 59.1 in


[kips]

WB 060-00001

239 1.63 0.479 0.051 0.148 0.097 0.198 2.70 7 " 0.94 0.31 0.13FV 060-00003

A4 060-00002


y z

yx z

y z

yx z

23

38

18

33.5

HZM

38/23

Scale 1:1

Fflex

L

Fz

L



Channel HZM 38/23

Accessories




VUS 40/25

Washer

SIC 38/23

Locking plate


1.496"

0.709"

0.118" 0.1

38"

0.9

06"



1.142"1.142"



M 6 0.49

M 8 0.90

M 10 1.28

M 12 1.28

Dimensions

GV

Thread

A4

Thread

a

[in]

b

[in]

d

[in]

M 6 M 6

1.319 0.689 0.236M 8 M 8

M 10 M 10

M 12 M 12

Dimensions HZS 38/23, HS 38/23 and HS 38/17

Length l[in]

HZS 38/23 HS 38/23 HS 38/17Length l

[in]

HZS 38/23 HS 38/23 HS 38/17

M 12 M 16 M 16 M 10 M 12 M 16 M 12 M 16 M 16 M 10 M 12 M 16

3/4 " GV GV GV 2 3/4 " FV8.8

1 " A4-70 A4-50 3 1/4 " GV8.8 GV8.8 GV GV GV GV

1 1/4 " GV8.8 GV8.8 GV GV GV GV A4-50/A4-70 A4-70 A4-50/A4-70

FV FV FV 3 1/4 "Li A4-50 A4-50

A4-70 A2-70/A4-70 A2-50/A4-50 4 " GV8.8 GV8.8 GV GV GV GV

1 1/2 " GV8.8 GV8.8 GV GV GV GV FV

FV A4-50 A4-50

A4-70 A2-70/A4-70 A2-50/A4-50 5 " GV8.8 GV8.8 GV GV GV

2 " GV8.8 GV8.8 GV GV GV GV 6 " GV8.8 GV8.8 GV GV GV GV

FV FV A4-50 A4-50

A4-70 A2-70/A4-70 A2-50/A4-50 8 " GV8.8 GV GV GV

2 "Li A4-50 A4-50 A4-50 A4-50

2 3/8 " GV8.8 GV8.8 GV GV GV GV/GV8.8 12 " GV8.8

A4-50/A4-70 GV8.8 FV8.8 High corrosion resistance stainless steel T-bolts HS 38/17Material order code HCR, available on request.A4-70 A4-70 A4-50


HALFEN T-bolts, toothedHZS 38/23 HALFEN T-bolts, HS 38/23, HS 38/17permissible load per T-bolt permissible load per T-bolt

Thread


HZS,Grade 8.8

[kips]

HZS,Grade A4-70


sx

[kips]


HS,Grade 4.6

[kips]

HS,Grade A4-50

[kips]

HS,Grade A4-70

[kips]

M 10 - - -

2.70

11 1.44 1.96 1.44

M 12 59 4.36 2.83 18 2.09 2.83 2.09

M 16 89 8.12 5.31 44 3.89 5.31 3.89

Note: do not exceed max. channel load bearing capacity; see pages 22. 56 Permissible moment load; see page 57

Note: HALFEN T-bolts HS are not suitable for loads in directionFSx

d

a

Fs

FsxFs



HALFEN T-bolts HZS 38/23, HS 38/23 and HS 38/17

Locking plate

HZS 38/23

HALFEN T-bolt

toothed,

incl. nut

HS 38/23

HALFEN T-bolt, incl.

nut

HS 38/17

HALFEN T-bolt,

incl. nut

Locking plate GWP 38/17

Li = Left hand thread



Dimensions and load capacities HZM 29/20



Channelcross-

section



G A Iy

Iz

Wy

Wz

Fz

19.7 in 39.4 in 59.1 in


[kips]

WB 050-00001239 1.02 0.307 0.025 0.058 0.056 0.102 1.798 5 " 0.540 0.16 0.07

FV 050-00003


y z

yx z

y z

yx z

29

20

14

2.52.5

ZM29

/20

Scale 1:1

Fflex

L

Fz

L



Channel HZM 29/20

Accessories




SIC 29/20

Locking plate

US DIN 9021

Washer


1.142"

0.551"

0.098"

0.0

98"

0.7

87

0.7

87"




Permissible Load Thread Load capacity [kips]

M 6 0.43

M 8 0.63

M 10 0.67

Dimensions

GV

Thread

A4

Thread

a

[in]

b

[in]

d

[in]

M 6 M 60.965 0.512 0.157

M 8 M 8

M 10 M 10 1.319 0.689 0.197

Dimensions HZS 29/20, HS 29/20 and HS 28/15

Length l[in]

HZS 29/20 HS 29/20 HS 28/15 Length l[in]

HZS 29/20 HS 29/20 HS 28/15

M 12 M 12 M 6 M 8 M 10 M 12 M 12 M 12 M 6 M 8 M 10 M 125/8 " GV GV GV 2 3/8 " GV8.8 GV GV GV GV" GV GV GV A4-70

A2-70/A4-70 3 1/4 " GV8.8 GV GV GV GV

1 " GV GV GV A4-70

A2-70 4 " GV8.8 GV GV GV

A4-70 A4-501 1/4 " GV8.8 GV GV GV GV GV 5 " GV8.8 GV GV

FV A4-50

A2-70/A4-70 A2-70/A4-70 6 " GV8.8 GV GV GV

1 1/2 " GV8.8 GV GV GV GV A4-50

FV8.8 8 " GV8.8 GV

A2-70/A4-70 A4-50

2 " GV8.8 GV GV GV GV GV 10 " GV8.8

FV 12 " GV8.8

A2-70/A4-70 High corrosion resistance stainless steel T-bolts HS 38/17,Material order reference HCR, available on request.2 "Li A4-50

Permissible load for HALFEN bolts

HALFEN T-bolt toothedHZS 29/20 HALFEN T-bolt HS 28/15, HS 29/20

permissible load per HALFEN T-bolt permissible load per HALFEN T-bolt


HZS,Grade 8.8


sx

[kips]


HS,Grade 4.6

[kips]

HS,Grade A4-50

[kips]

HS,Grade A4-70

[kips]Thread

M 6 - -

1.80

2 0.49 - -

M 8 - - 6 0.90 1.24 0.90

M 10 - - 11 1.44 1.96 1.44

M 12 59 4.36 18 2.09 - -

Note: do not exceed max. channel load bearing capacity; see pages 24. 56 Permissible moment load; see page57

Note: HALFEN T-bolts HS are not suitable for loads in direction FSx

Fs

FsxFs

b

d

aLocking plate GWP 28/15



HALFEN T-bolts HZS 29/20, HS 28/15 and HS 29/20

Locking plate

HZS 29/20HALFEN T-bolt

toothed

incl. nut

HS 28/15HALFEN T-bolt, incl.

nut

HS 29/20HALFEN T-bolt, incl.

nut

Assembly note:

M 6 and M 8:Insert locking plate at an angle

through the channel slit.

M 10:First insert the locking plate then screw

in the threaded rod.

0.827" 0.787"



Dimensions and load bearing capacities HZL 63/63



Channelcross-

section



G A Iy

Iz

Wy

Wz

Fz

19.7 in 39.4 in 59.1 in


[kips]

FV 030-00001 1184.27 1.099 0.795 1.032 0.614 0.832 1.26 52 " 3.71 1.84 1.24

FV 030-00003 236


y z

yx z

y z

yx z

63

63

22

7

9.5 9.5

2.5

3

HALFEN

Scale 1:1

Fflex

L

Fz

L

28

14

250

HZL6

3/63

toothing


Heavy duty f raming and mount ing channel

Framing channel HZL 63/63

Accessories

HZL 63/63 cold-rolled, toothed

HALFEN T-bolts and locking platesHZS 41/41, HZS 41/22,

GWP 41/41, GWP 41/22

see medium duty framing system

see pages 34,35 see page 46 see page 46

HPE 63/63 Channel end caps PA - 41 Channel cover

For further channel data and static properties see page 52

Base channel for HALFEN Powerclick

System 63. Information about the Power-

click assembly system can be found in our

product catalogue "HALFEN Powerclick

Technical Product Information PC63".

2.480"

9.843"

1.102"

0.551"

0.118"

0.098"

0.276"

0.374" 0.866" 0.374"

2.4

80"

34/



Dimensions and load capacities HM 41/41 and HL 41/41

Material Order-no.


Channelcross-

section



G A Iy

Iz

Wy

Wz

Fz

19.7 in 39.4 in 59.1 in


[kips]

HM 41/41 0280.

236

1.75 0.516 0.172 0.222 0.187 0.272 1.26 19" 1.21 0.61 0.40

WB 080-00001

SV 080-00002

FV 080-00003

A4 080-00004

HL 41/41 0281.

1.65 0.462 0.146 0.220 0.173 0.270 1.26 16" 1.06 0.52 0.36

WB 010-00001

SV 010-00003

FV 010-00002

A4 010-00004

HM 41/41 D 0280.

3.58 1.034 0.860 0.443 0.529 0.545 1.26 52"

39.4 in 59.1 in 78.7 in

WB 150-00001

1.64 1.10 0.83FV 150-00003

A4 150-00002


y z

yx z

y z

yx z

41

41

22

7

2.5

HM

41/41

HL41/41

14

28

50

HM

41/41

D

Scale 1:1

Fflex

L

Fz

L


Framing Channel HM 41/41 and HL 41/41

Accessories

HM 41/41 and HL 41/41 cold-rolled

For further channel data and static properties see pages 50, 52


Medium duty f raming and mount ing channels


Double channelon request

1.614"

0.866"

0.098"

0.551"

1.6

14"

0.2

76"

1.969"

1.102"



HZM

41/41

Dimensions and load capacities HZM 41/41 and HZL 41/41

Material Order-no.


Channelcross-

section



G A Iy

Iz

Wy

Wz

Fz

19.7 in 39.4 in 59.1 in


[kips]

HZM 41/41 0284.

236

1.77 0.504 0.166 0.219 0.178 0.269 1.26 18" 1.17 0.58 0.38WB 010-00001

FV 010-00002

A4 010-00003

HZL 41/41 0283.

1.65 0.450 0.141 0.217 0.164 0.267 1.26 16" 1.01 0.52 0.25WB 010-00001

FV 010-00002

A4 010-00003

HZM 41/41 D 0284.

3.43 1.009 0.811 0.442 0.498 0.543 1.26 49 "

39.4 in 59.1 in 78.7 in

WB 030-00001

1.55 1.03 0.79FV 030-00002

A4 030-00003


y z

yx z

y z

yx z

HZL4

1/41

0.551"

1.102"

1.969"

41

41

22

7

2.5

HZM

41/41D

Scale 1:1

Fflex

L

Fz

L



Framing channel HZM 41/41 and HZL 41/41

Accessories

HZM 41/41 and HZL 41/41 cold-rolled, toothed

For further channel data and static properties see pages 50, 52



0.098"

0.866"0.2

76"

1.614"

1.6

14"




Material Order-no.


Channelcross-

sectiont



G A Iy

Iz

Wy

Wz

Fz

39.4 in 78.7 in 118 in

[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] Fflex[kips]

HM 41/62 0280.

236

2.30 0.676 0.485 0.315 0.361 0.388 1.26 36" 1.15 0.58 0.34WB 140-00002

SV 140-00001

FV 140-00003

HL 41/62 0281.

2.11 0.618 0.415 0.313 0.334 0.385 1.26 32" 1.01 0.49 0.29WB 040-00001

SV 040-00003

FV 040-00002

HM 41/62 D0280.

4.60 1.352 2.597 0.630 1.065 0.774 1.26 106"

39.4 in 59.1 in 78.7 in

WB 170-000013.33 2.23 1.66

FV 170-00002 F


y z

y

x z

y z

y

x z

41

62

22

7

2.5

HM41

/62

HL41/62

0.551"

1.102"

1.969"

HM41

/62D

Scale 1:1

Fflex

L

Fz

L



see page 46

Framing channel HM 41/62 and HL 41/62

Accessories





Note for span distance L:Brace channel during installation to prevent

possible buckling or twisting when load is

applied.

1.614"

0.276"

0.098"

0.866"

2.4

41"




Material Order-no.


Channelcross-

section



G A Iy

Iz

Wy

Wz

Fz

39.4 in 78.7 in 118 in

[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] Fflex [kips]

HM 41/83 0280.

236

2.84 0.835 1.021 0.408 0.581 0.502 1.26 58" 1.84 0.92 0.61WB 130-00002

SV 130-00001

FV 130-00003

HL 41/83 0281.

2.64 0.778 0.891 0.407 0.540 0.500 1.26 52" 1.64 0.83 0.54WB 030-00004

SV 030-00006

FV 030-00005F


y z

yx z

y z

yx z

41

83

22

7

2.5

HM41

/83

0.551"

28

50

HL41

/83

1.102"

1.969"

Scale 1:1

Fflex

L

Fz

L



Framing channels HM 41/83 and HL 41/83

Accessories

HM 41/83 andHL 41/83 cold-rolled



see page 46


Note for span distance L:

Ensure that the channel mounting

structure is braced to prevent late-

ral torsional buckling when load is

applied.

1.614"

0.098"

0.866"

0.2

76"

3.268"



Dimensions and load bearing capacities HM 41/22 and HL 41/22

Material Order-no.


Channelcross-

section



G A Iy

Iz

Wy

Wz

Fz

19.7 in 39.4 in 59.1 in


[kips]

HM 41/22 0280.

236

1.20 0.357 0.029 0.128 0.059 0.157 1.26 5 " 0.40 0.18 0.09

WB 120-00001

SV 120-00002

FV 120-00003

A4 120-00004

HL 41/22 0281.

1.10 0.302 0.024 0.127 0.054 0.156 1.26 4 " 0.36 0.16 0.07

WB 020-00001

SV 020-00003

FV 020-00002

A4 020-00004

HM 41/22 D 0280.

2.42 0.711 0.133 0.256 0.164 0.314 1.26 16"

39.4 in 59.1 in 78.7 in

WB 160-00001

0.52 0.34 0.20FV 160-00002

A4 160-00003


y z

yx z

y z

yx z

41

21

22

7

2.5

HM41

/22

HL41

/22

0.551"

1.102"

1.969"

HM41

/22D

Scale 1:1

Fflex

L

Fz

L


Accessories








1.614"

0.866"

0.098"

0.8

27"

0.2

76"



Dimensions and load bearing capacities HZM 41/22 and HZL 41/22

Material Order-no.


Channelcross-

section



G A Iy

Iz

Wy

Wz

Fz

19.7 in 39.4 in 59.1 in


[kips]

HZM 41/22 0284.

239 1.20 0.344 0.028 0.125 0.056 0.154 1.26 5" 0.38 0.18 0.07WB 020-00001

FV 020-00002

A4 020-00003

HZL 41/22 0283.

236 1.10 0.290 0.023 0.124 0.052 0.151 1.26 4 " 0.34 0.13 0.07WB 020-00001

FV 020-00002

A4 020-00003

HZM 41/22 D 0284.

239 2.41 0.722 0.136 0.264 0.164 0.325 1.26 16"

39.4 in 59.1 in 78.7 in

WB 040-00001

0.52 0.34 0.20FV 040-00002

A4 040-00003


y z

yx z

y z

yx z

41

21

22

7

2.5

HZM

41/22

HZM

41/22

D

0.551"

1.102"

1.969"

HZL4

1/22

Scale 1:1

Fflex

L

Fz

L



Framing channels HZM 41/22 and HZL 41/22

Accessories

HZM 41/22 and HZL 41/22 cold-rolled, toothed



HPE 41/41 Channel end cap



1.614"

0.098"

0.866"

0.8

27"

0.2

76"



Dimensions and load capacities HLL 41/41 and HLL 41/22

Material Order-no.


Channelcross-

section



G A Iy

Iz

Wy

Wz

Fz

19.7 in 39.4 in 59.1 in


[kips]

HLL 41/41 0282.

236

1.08 0.298 0.102 0.147 0.124 0.180 0.40 35 /" 0.72 0.36 0.22SV 010-00002

HLL 41/22 0282.0.77 0.206 0.018 0.088 0.043 0.109 0.40 12/" 0.25 0.09 0.04

SV 020-00003


y z

yx z

y z

yx z

41

21

22

7

1.50.551"

1.102"

1.969"

HLL4

1/22

41

41

22

7

.5

1.5

HLL4

1/41

0.551"

1.102"

1.969"

Scale 1:1

Fflex

L

Fz

L



Framing channels HLL 41/41 and HLL 41/22

Accessories

HLL 41/41 cold-rolled HLL 41/22 cold-rolled

HPE 41/41



1.614"

1.614"

0.866"

0.866"

0.059"0.059"

1.6

14"

0.8

27"

0.2

76"

0

.295"



Dimensions HZS 41/41, HZS 41/22 and HS 41/41

Length l["]

HZS 41/41 HZS 41/22 HS 41/41

M6 M8 M10 M12 M16 M12 M16 M10 M12

11/4 " zinc flake coated zinc flake coated zinc flake coated zinc flake coated

13/8 " FV8.8 A4-50 FV4.6 FV4.6

A4-50 A4-50 A4-50

2"zinc flake coated zinc flake coated zinc flake coated

FV8.8 FV8.8 FV4.6

A4-50 A4-50

2 1/2 " zinc flake coated

3 " zinc flake coated zinc flake coated

3 1/4 " A4-50

4 " zinc flake coated FV8.8

FV

4 1/32" zinc flake coated


HALFEN T-bolts toothedHZS 41/41 HALFEN T-bolts toothedHZS 41/22 HALFEN T-bolts HS 41/41

permissible load per T-bolt permissible load per T-bolt recomm. load per T-bolt

Tighte-ning

torque[lb.ft]

allchannels

Fs[kips]

HM/HL

Fsx[kips]

HZM/HZL

Fsx[kips]

Tighte-ning

torque[lb.ft]

HLL

Fsx[kips]

Tighteningtorque

Grade 8.8

(Grade A4)[lb.ft]

allchannelsGrade8.8

Fs[kips]

HZM/HZL

Grade8.8

Fsx[kips]

allchannelsGradeA4-50

Fs[kips]

HM/HL

GradeA4-50

Fsx[kips]

HZM/HZL

GradeA4-50

Fsx[kips]

Tightening

torque[lb.ft]

HM/HLGrade4.6

Fs[kips]

HM/HLGrade 4.6

Fsx[kips]

HM/HLGradeA4-50

Fs[kips]

HM/HLGradeA4-50

Fsx[kips]Thread

M 6 9 1.12 0.22 0.49 9 0.22 - - - - - - - - - - -

M 8 21 1.35 0.54 0.90 21 0.54 - - - - - - - - - - -

M 10 41 1.57 0.79 1.12 41 0.79 - - - - - - - - - - -

M 12 44 1.57 0.90 1.12 41 0.81 37 (37) 1.57 1.12 1.57 0.38 1.12 11 (11) 1.44 0.07 1.44 0.07

M 16 92 2.70 1.69 1.69 70 1.01 59 (59) 2.70 1.69 2.70 0.90 1.12 18 (18) 2.09 0.11 6.86 0.11

Note: do not exceed max. channel load bearing capacity; see pages 2733 and 56

Fs FsFsx Fsx Fsx

Fs

l

34.5

l

34.5

1.39"

l


Halfen T -bolts and accessor ies

HALFEN T-bolts HZS 41/41, HZS 41/22 and HS 41/41

HZS 41/41

HALFEN T-bolts

toothed

(order nut separately)

HZS 41/22

HALFEN T-bolts

toothed, incl. nut

HS 41/41

HALFEN T-bolts,

incl. nut

HALFEN T-bolts for all 41 profiles':

for toothed Profiles

41/41 and 41/22

Application notes: HZS 41/41:

- M16not suitable for channels 41/22

- M16can only be mounted by sliding on at channel end

- M16x 4 / without teeth, FSx

= 0.90 kips

1.358"

1.358"

1.386"



Dimensions GWP 41/41 SN

GV

Thread

d

[in]

b

[in]

a

[in]

M 6 0.236

0.787 1.358

M 8 0.315

M 10

0.354

F M 12

Load Bearing capacity GWP 41/41, - SN, -SH

Thread

all ProfilesF

S

[kips]


HM/HLF

Sx

[kips]

HZM/HZLF

Sx

[kips]


HLLF

Sx

[kips]

HM/HLF

S

[kips]


HM/HLF

Sx

[kips]

HZM/HZLF

Sx

[kips]

M 6 1.12 2.70 0.22 0.49 2.70 0.22 1.12 1.46 0.07 0.49

M 8 1.35 6.29 0.54 0.90 6.29 0.54 1.35 3.60 0.13 0.90

M 10 1.57 12.36 0.79 1.12 12.36 0.79 1.57 7.08 0.27 1.12

M 12 2.02 16.86 1.12 1.12 12.36 0.81 - - - -

F M12 1.57 13.49 0.90 1.12 12.36 0.81 1.57 12.36 0.38 1.12

M16 2.70 28.10 1.69 1.69 21.36 1.01 2.70 28.10 0.90 1.12

Load bearing capacity GWP 41/22

Thread

FS

[kips]


HZM/HZLF

Sx

[kips]

HM/HLF

S

[kips]


HM/HLF

Sx

[kips]

HZM/HZLF

Sx

[kips]

M 6 1.12 2.70 0.22 - - - -

M 8 1.35 6.29 0.54 1.35 3.60 - 0.90

M 10 1.57 12.36 0.79 1.57 7.08 - 1.12

M 12 2.02 11.24 0.81 1.57 11.24 - 1.12

M 16 1.57 17.98 1.01 1.57 17.98 - 1.12

Dimensions GWP 41/41

GV

Thread

FV

Thread

A4

Thread

d

[in]

b

[in]

a

[in]

M 6 M 6 0.234

0.787

1.358

M 8 M 8 M 80.315 /0.236

M 10 M 10 M 10

0.354F M12 F M12 F M12

M12 M12 0.472

M16 M16 0.472 1.181

Dimensions GWP 41/22

GV

Thread

A4

Thread

d

[in]

b

[in]

a

[in]

M 6 -

0.295 0.787 1.358

M 8 M 8

M 10 M 10

M 12 M 12

M 16 M16

On request

Dimensions GWP 41/41 SH

GV

Thread

d

[in]

b

[in]

a

[in]

M 6 0.236

0.787 1.358

M 8 0.315

M 10 0.354

M 12 0.472

b a

d

ba

dd

ba

b

d

a

Fsx Fsx

Fsx Fsx


Locking p lates Medium duty f raming and mount ing system

Locking plates

GWP 41/41

Locking plates

GWP 41/41 SN

Locking plates

GWP 41/41 SH

Locking plate

GWP 41/22

Locking plates GWP 41/41 - SN, - SH, GWP 41/22

Locking plates for all 41profiles and

profile 63/63

Locking plates with short spring for

profiles 41/22and 63/63

Locking plates with long spring for

profile 41/41

Locking platefor toothed channels

41/22 and 41/41

Application notes: GWP 41/41: - M12 + M16not suitable for channels 41/22 and 63/63

- M16can only be mounted by sliding on at channel end

UNC threads are available. Please contact Halfen customer service.



Dimensions and load capacities HM 36/36, HL 36/36, HM 38/17

Material Order-no.


Channelcross-

section


t


G A Iy

Iz

Wy

Wz

Fz

19.7 in 39.4 in 59.1 in

[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] Fflex[kips]

HM 36/36 0280.

236

1.47 0.432 0.108 0.141 0.133 0.198 0.99 17" 0.88 0.43 0.29WB 070-00001FV 070-00002

A4 070-00003

HL 36/36 0281.

1.34 0.375 0.088 0.139 0.120 0.196 0.99 14/" 0.72 0.36 0.25WB 050-00001

FV 050-00002

A4 050-00003

HM 38/17 0280.

239 1.22 0.357 0.020 0.103 0.050 0.138 1.08 4" 0.34 0.13 0.07

WB 020-00001

FV 020-00002

A2 020-00003

A4 020-00004


y z

yx z

y z

yx z

36

36

18

2.5

HM36

/361.5

75"

2.362"

0.591"

HL36

/36

38

17

.53

18 HM

38/17

Scale 1:1

Fflex

L

Fz

L


Light duty f raming and mount ing channels

Framing channels HM 36/36, HL 36/36 and HM 38/17

Accessories

HM 36/36 and

HL 36/36 cold-rolledHM 38/17 cold-rolled

For further channel data and staticproperties see pages 50, 52


see page 45 see page 46 see page 46

HPE 36/36Channel end cap

for HM 36/36

and HL 36/36

PA - 18H Channel cover

1.417"

1.496"

0.709"

0.118"0.098"

0.709

1.4

17"

0.6

89"





M 6 0.49

M 8 0.90

M 10 1.28

M 12 1.28

Dimensions

GV

Thread

A4

Thread

a

[in]

b

[in]

d

[in]

M 6 M 6

1.319 0.689 0.236M 8 M 8

M 10 M 10

M 12 M 12


for standard steel profile for stainless steel profiles

permissible loadper HALFEN T-bolt

recomm. load per T-boltin longitudinal channel direction

permissible loadper HALFEN T-head bol

recomm. load per T-boltin longitudinal channel direction

Grade Grade HS, Grade 4.6 HS, Grade 8.8

HS, GradeA2/A4 - 50

[kips]

HS, GradeA2/A4 - 70

[kips]

HS, GradeA2/A4 - 50/70

[kips]Tightening torque

[lb.ft]Thread

4.6[kips]

8.8[kips]

[kips]



M 10 1.44 2.99 0.07 11 0.25 35 1.44 1.96 0.07 11

M 12 2.09 4.36 0.11 18 0.36 52 2.09 2.83 0.11 18

M 16 3.89 8.12 0.20 44 0.67 148 3.89 5.31 0.20 44


Dimensions HS 38/17

Length l["]

Length l["]M 10 M 12 M 16 M 10 M 12 M 16

3/4" GV GV GV 23/8 " GV GV GV

1 " A4-70 A4-50 FV8.8

1 1/4 " GV GV GV A4-70 A4-70 A4-50

FV FV FV 23/4 " FV8.8

A4-70 A2-70 A2-50 31/4 " GV GV GV

A4-70 A4-50 A4-70 A4-50

1 1/2 " GV GV GV 31/4 "Li A4-50 A4-50

FV 4" GV GV GV

A4-70 A2-70 A2-50 FV

A4-70 A4-50 A4-50 A4-502" GV GV GV 5" GV GV

FV FV 6" GV GV GV

A4-70 A2-70 A2-50 A4-50 A4-50

A4-70 A4-50 8" GV GV

2" Li A4-50 A4-50 A4-50 A4-50

High corrosion resistance stainless steel T-bolts HS 38/17,Material order code HCR, available on request.

Fsx FsxFs Fs


HALFEN T-bolts a nd accessor ies

Locking plates GWP 38/17

HALFEN T-bolts HS 38/17

Locking plates

HS 38/17

HALFEN T-bolts incl. nutLi = with left hand thread

1.142"




Material Order-no.


Channelcross-

section



G A Iy

Iz

Wy

Wz

Fz

19.7 in 39.4 in 59.1 in


[kips]

HM 28/28 0280.

236

0.91 0.268 0.041 0.048 0.066 0.091 0.67 12 /" 0.43 0.20 0.11

WB 050-00001

SV 050-00003

FV 050-00002A4 050-00004

HL 28/28 0281.

0.82 0.229 0.032 0.048 0.058 0.090 0.67 10 /" 0.34 0.18 0.09

WB 060-00001

SV 060-00003

FV 060-00002

A4 060-00004


28

12

27

2

HM28

/28

12,5

25

40

HL28

/28

Scale 1:1

y z

yx z

y z

yx z Fflex

L

Fz

L


Accessories




see page 46

HPE 28/28 Channel end cap



1.063"

0.492"

0.984"

1.575"

0.079"

0.472"

1.1

02"




Material Order-no.


Channelcross-

section



G A Iy

Iz

Wy

Wz

Fz

19.7 in 39.4 in 59.1 in


[kips]

HM 26/26 0280.

236

0.55 0.163 0.023 0.028 0.039 0.055 0.25 19 " 0.25 0.11 0.07SV 040-00001

HL 26/26 0281.0.48 0.138 0.018 0.028 0.034 0.054 0.25 15 " 0.20 0.90 0.05

SV 070-00001F


26

26

12

1.25

HM26

/26 25

40

HL26/26

12,5

Scale 1:1

y z

yx z

y z

yx z

Fflex

L

Fz

L


Accessories




HPE 26/26Channel end cap



see page 46

1.024"

0.049"

0.472"

0.492"

1.575"

0.984"1

.024"

/

1116/



Dimensions and load bearing capacities HM 315 (C30)

Mat. Order-no.0280.

LengthChannelweight

Channelcross-

section

Moment ofinertia

Moment ofresistance

Max. point-loadbearing capacity

Bending load capacityfor span L [in]

G A Iy

Iz

Wy

Wz

Fz

19.7 in 39.4 in 59.1 in


[kips]

WB 060-00001236 0.52 0.150 0.007 0.030 0.020 0.051 0.37 6.969 0.13 0.04 0.02

FV 060-00002


y z

yx z

y z

yx z

Dimensions and load capacities HM 28/15, HL 28/15, HM 315 (C30)

Material Order-no.


Channelcross-

section



G A Iy

Iz

Wy

Wz

Fz

19.7 in 34.4 in 59.7 in


[kips]

HM 28/15 0280.

239

0.73 0.215 0.010 0.035 0.028 0.063 0.877 3.228 0.18 0.07 0.03

WB 010-00001

FV 010-00002

A2 010-00004

A4 070-00003

HL 28/15 0281.

0.58 0.180 0.008 0.032 0.024 0.060 0.877 2.756 0.16 0.05 0.02

WB 080-00001

FV 080-00004A2 080-00002

A4 080-00003


Fflex

L

Fz

L

15

.25

12

28

2.25

HM28

/15 25

40

HL28

/15

15

16

30

1.5

HM31

5

Scale 1:1

Scale 1:1

y z

yx z

y z

yx z

Fflex

L

Fz

L



Framing channel HM 28/15, HL 28/15 and HM 315 (C30)

Accessories

HM 28/15 andHL 28/15 cold-rolled

HM 315 (C30) cold-rolled




see page 45

1.102"

1.181

0.059

0.630

0.089"

0.472"

0.354"

1.575"

0.984"

0.6

00"

0.5

91



Dimensions HS 28/15

Length l["]

Length l["]M 6 M 8 M 10 M 12 M 6 M 8 M 10 M 12

5/8" GV GV GV 2 " GV GV GV GV3/4" GV GV GV FV

A2-70 A2-70

A4-70 A4-70

1 " GV GV GV 2 3/8" GV GV GV

A2-70 A4-70

A4-70 3 1/4" GV GV GV

1 1/4" GV GV GV GV A4-70

FV 4 " GV GV

A2-70 A2-70 A4-50

A4-70 A4-70 5 " GV

1 1/2" GV GV GV A4-50FV8.8 6 " GV GV

A2-70 A4-50

A4-70 8 " GV

2 "Li A4-50 A4-50

High corrosion resistance stainless steel HALFEN T-bolts HS 28/15,Material order code HCR, available on request.



M 6 0.43

M 8 0.63

M 10 0.67

Dimensions

GV

Thread

A4

Thread

a

[in]

b

[in]

d

[in]

M 6 M 60.965 0.512 0.157

M 8 M 8

M 10 M 10 1.319 0.689 0.197

Installation note:M 6 and M 8:Insert locking plate at a slant anywhere through the channel opening.

M 10:First insert the locking plate then screw in the threaded rod.




recomm. load per HALFEN T-bolt-in longitudinal channel direction


recomm. load per HALFEN T-bolt-in longitudinal channel direction

HS, GradeA2/A4 - 50

[kips]

HS, GradeA2/A4 - 70

[kips]

HS, GradeA2/A4 - 50/70


[lb.ft]Thread

Grade4.6

[kips]

HS, Grade4.6


[lb.ft]

M 6 0.49 0.02 2 0.49 0.67 0.02 2

M 8 0.90 0.04 6 0.90 1.24 0.04 6

M 10 1.44 0.07 11 1.44 1.96 0.07 11

M 12 2.09 0.11 18 2.09 2.83 0.11 18

Note: do not exceed max. channel load bearing capacity. see page 40

Fsx FsxFs Fs


HALFEN T-bolts a nd accessor ies


HALFEN T-bolt HS 28/15

Locking plates

HS 28/15

HALFEN T-bolt incl. nut

(not for HM 315)

for Profiles 28/15 and 315 (C30)

Li = with left hand thread

0.787"



Dimensions and load bearing capacities HM 20/12 and HL 20/12

Material Order-no.


Channelcross-

section



G A Iy

Iz

Wy

Wz

Fz

19.7 in 39.4 in 59.1 in


[kips]

HM 20/12 0280.

236

0.35 0.102 0.003 0.009 0.010 0.022 0.504 2.283 0.07 0.02 0.01WB 030-00001

FV 030-00003

A2 030-00002

HL 20/12 0281.

0.30 0.082 0.002 0.008 0.009 0.022 0.504 1.811 0.05 0.01 0.01WB 090-00001

FV 090-00002

A2 090-00003


12

10

20

1.5

HM20

/12 HL

20/12

0.354

0.984

1.575

SIC

Scale 1:1

y z

yx z

y z

yx z

Fflex

L

Fz

L


Light duty f raming and mount ing systems


Accessories

HM 20/12 and

HL 20/12 cold-rolled




see page 45

0.787"

0.394"

0.059"

0.4

72"



Dimensions HS 20/12

Length l["] M 6 M 8

5/8" GV3/4" GV GV

A2-70

1 " GV

1 1/4" GV GV

A2-70

1 1/2" GV GV

A2-70

2" GV GV

A2-702 3/8" GV GV

3 1/4" GV

4" GV

Dimensions

GV

Thread

A4

Thread

a

[in]

b

[in]

d

[in]

M 5 M 5

0.630 0.354 0.157

M 6 M 6


permissible load Thread Load capacity [kips]

M 5 0.34

M 6 0.43

Permissible loads for T-bolts1



permissible loadper HALFEN T-bolt in

longitudinal channel direction


permissible loadper HALFEN T-bolt in

longitudinal channel direction

Grade



Tightening torque[lb.ft]Thread

4.6[kips]

HS, Grade4.6


[lb.ft]

M 6 0.49 0.02 2 0.67 0.02 2

M 8 0.90 0.04 6 1.24 0.04 6

Note: do not exceed max. channel load bearing capacity see page 42

Fsx FsxFs Fs

l

15.5


HALFEN T-bolts HS 20/12

Locking plates

HS 20/12

HALFEN T-bolts

incl. nut



0.610"



GVFK 4.6

Thread

Stainless steelA4

Thread

Length

[in]

Loadcapacity

[kips]M 6 M 6 39.4 0.49

M 8 M 8 39.4 0.90

M 10 M 10 39.4 1.44

M 12 M 12 39.4 2.09

M 16 M 16 39.4 3.89

M 20 M 20 39.4 6.07

M 24 39.4 8.72

Order example:: GWS - M 12 1000 - GV

GVFK 8.8

Dimensions

Stainless steelA4

Dimensions

S S

DIN EN

[in] [in]

M 6x 12 0.394 0.394

M 6x 25

M 8 x 25 M 8 x 250.512 0.512

M 8 x 40

M 10 x 20

0.669 0.630

M 10 x 30 M 10 x 30

M 10 x 45 M 10 x 45

M 10 x 60

M 10 x 70

M 12 x 22

0.748

0.709

M 12 x 25 M 12 x 25

M 12 x 30 M 12 x 30

M 12 x 40 M 12 x 40

M 12 x 50

M 12 x 60 M 12 x 60M 12 x 80 M 12 x 80

M 12 x 90

M 16x 40 M 16x 40

0.945 0.945M 16x 60 M 16x 60

M 16x 90 M 16x 90

GVFK 8

Thread

Stainlesssteel A4Thread

S/m S/m e

DIN ISO DIN

[in] [in] [in]

M 6 M 6 0.394/0.197 0.394/0.236 0.453

M 8 M 8 0.512/0.256 0.512/0.295 0.591

M 10 M 10 0.669/0.315 0.630/0.374 0.772

M 12 M 120.748/0.394 0.709/0.472 0.862

M 16 M 16 0.945/0.512 0.945/0.610 1.091

M 20 M 20 1.181/0.630 1.181/0.748 1.362

M 24 M 24 1.417/0.748 1.417/0.866 1.634

FV

Thread

Stainlesssteel A2Thread

S/m S/m e

DIN EN

[in] [in] [in]

M6, M8 M 8 0.512/0.256 0.512/0.295 0.591

M 10 M 10 0.669/0.315 0.630/0.374 0.772

M 12 M 12 0.748/0.394 0.709/0.472 0.862

M 16 M 16 0.945/0.512 0.945/0.610 1.091

GV

for Screw size

Stainlesssteel A4

for Screwsize

D d s

[in] [in] [in]

M 6 M 6 0.472 0.252 0.063

M 8 M 8 0.630 0.331 0.063

M 10 M 10 0.827 0.413 0.079

M 12 M 12 0.945 0.512 0.098

M 16 M 16 1.181 0.669 0.118

M 20 M 20 1.457 0.827 0.118

M 24 M 24 1.732 0.984 0.157

FV

for Screw size

Stainlesssteel A2for Screw

size

D d s

[in] [in] [in]

M 8 0.669 0.331 0.063

M 10 M 10 0.827 0.413 0.079

M 12 M 12 0.945 0.512 0.098

M 16 M 16 1.181 0.669 0.118

Order example:: US - GV - M 12 - DIN 125

DINEN

GVfor Screw

size

Stainlesssteel A4for Screw

size

D d s

[in] [in] [in]7094 M 6 0.866 0.260 0.079

7093-1 M 8 M 8 0.945 0.331 0.079

7093-1 M 10 M 10 1.181 0.413 0.098

7094 M 12 1.772 0.531 0.157

7093-1 M 12 M 12 1.457 0.512 0.118

7093-1 M 16 M 16 1.969 0.669 0.118

7094 M 20 2.835 0.866 0.236

Order example:: US - M 12 - GV - DIN EN ISO 7093-1

FV

Type

Stainlesssteel A4

Type

t b d F

[in] [in] [in] [kips]

1 1 0.236 1.575 0.512 0.34

2 2 0.315 1.969 0.669 0.74

3 3 0.394 1.969 0.669 1.12

recommended. max. load

3.

937

0.787

1.969

Cross-section

GWS

Threaded rod

DIN 976-1

HSK

Hex. head bolt

DIN 933 or

DIN EN ISO 4017

(without nut)

MU

Hex. head nut

DIN 934 or

DIN EN ISO 4032

Hex. head T-bolts areused in combinationwith HALFEN lockingplates

US

Washers

DIN EN ISO

7093-1/7094,

DIN 440

US

Washers

DIN 125/

DIN EN

ISO 7089

HJV

Adjustment

coupler


Threaded rods, hexagon head bolts, nuts, washers



GV

thread size

Stainlesssteel A4

thread size

D Lload

capacity

[in]

[in]

[kips]M 6 M 6 0.394/0.394 0.591 0.49

M 8 M 8 0.472/0.551 0.787 0.90

M 10 M 10 0.512/0.630 0.984 1.44

M 12 M 12 0.630/0.787 1.181 2.09

M 16 M 16 0.827/0.984 1.575 3.89

M 20 M 20 1.024/1.260 1.969 6.07

Recomm. maximum working load at centric-pull

Size D for type GV / A4

FV

thread size

Stainlesssteel A4

thread size

S Lload

capacity

[in]

[in]

[kips]

M 10 M 10 0.512 1.575 1.44

M 12 M 12 0.669 1.575 2.09

M 16 M 16 0.866 1.969 3.89

Recomm. maximum working load at centric-pullOrder example: SKM - FV - M 12

Stainless steel A4

Thread M 12 Length L [in]

Stainless steelA4

Thread M 16 Length L [in]

D D

forM12[in]

forM16[in]

M12 60 M16 60 0.630 0.866

M12 75 M16 75 0.630 0.866

M12 95 M16 95 0.630 0.866

M12 115 M16 115 0.630 0.866

M12 135 M16 135 0.630 0.866perm. load: 5 kips

Order example: SPH - A4 - M 12 x 75

GV

Itemdescription

Stainless steel

A4

Itemdescription

forHALFEN Bolt

Type Dimensions

SIC - 50/30 - GV SIC - 50/30 - A4 50/30 M16, M20

SIC - 40/22 - GV SIC - 40/22 - A438/1740/22

M16

SIC - 38/23 - GV 38/23 M16

SIC - 29/20 - GV 29/20 M12

SIC - 38/17 - GV SIC - 38/17 - A438/1740/22

M12, M10

SIC - 28/15 - GV SIC - 28/15 - A4 28/15 M8, M10

SIC - 20/12 - GV SIC - 20/12 - A4 20/12 M8

Order example: SIC - 38/17- GV

GVC 15 E

thread size

d load capacity

[in]

[kips]

M 8 0.787 0.31

M 10 0.984 0.52

M 12 1.181 0.76

M 16 1.378 1.57

M 20 1.575 2.70

Recomm. maximum working load at centric-pull

according to DIN 582

VUSsquare washers FV

thread size

Stainless steelA4

thread size

a x b x d

[in]

VUS 40/25for profiles40/25;HZA41/22

M 10 M 10 1.575 x 1.575 x 0.197M 12 M 12 1.575 x 1.575 x 0.197

M 16 M 16 1.575 x 1.575 x 0.197

VUS 49/30for profiles54/33,49/30

M 10 M 10 1.457 x 1.457 x 0.197

M 12 M 12 1.457 x 1.457 x 0.197

M 16 M 16 1.457 x 1.457 x 0.197

M 20 M 20 1.457 x 1.457 x 0.197


M 16 M 16 1.969 x 1.969 x 0.236

M 20 M 20 1.969 x 1.969 x 0.236


M 20 M 20 2.126x 2.126x 0.236

M 24 M 24 2.126x 2.126x 0.236

M 27 M 27 2.126x 2.126x 0.236

M 30 M 30 2.126x 2.126x 0.236

VUS 41/41for all 41 profiles

M 6 M 6 1.575 x 1.575 x 0.236

M 10 M 10 1.575 x 1.575 x 0.236

M 12 M 12 1.575 x 1.575 x 0.236

Order example: VUS 52/34 - FV - M 20

perm. load: 10 kips


Couplers, Ring nuts, Square washers

VBM

Coupler, round

SKMHexagonal rod

Coupler with

view hole

SPHTurnbuckle

(right and left-

hand thread)

SIC

Locking plate

Application:

To prevent T-bolts

turning during assembly.

RM

Ring-nut

(DIN 582Issue date 2003-8)

f = min.Screw-in depthM12 = 10 mmM16= 13 mm

Assembly Diagram:

HALFEN Channel

HALFEN Bolt

Locking plate SIC



Order no.

Description Item no. For

0318.000- Channel

HPE 63/63 00010 63/63

HPE 52/34 00001 52/34

HPE 50/40 00002 50/40

HPE 41/41 00003 41/41

HPE 41/22 00004 41/22

HPE 36/36 00005 36/36HPE 28/28 00006 28/28

HPE 28/15 00011 28/15

HPE 26/26 00007 26/26

Order-no.

Type length Item-no.

0321.000-PA - 41 - KS 9' 10" 00002

PA - 41 - SV 9' 10" 00001

PA - 22 - KS 9' 10" 00003

PA - 18H - KS 9' 10" 00004

Type overview

Type: PA 41 PA 22 PA 18 H

Material:hard PVC

(KS)

1.614

0.827

0.3

54

1.083"

0.866"

0.5

91"

1.083"

0.1

9

7"

white medium gray medium gray

Material:Steel

pre-galvanized(SV)

1.614

0.827

.354

suitable for profiles:50/40, 50/30, 486,

all 41 profiles

suitable for profile52/34

suitable for profile36/36, 38/17

HALFENHALFEN

PA 2 2

0.5

91


Channel end caps, Channel cover s t r ip

Assembly diagramChannel end caps in plastic

Type HPE 63/63

color: blue

Type HPE

color: black

Type HPE 41/41

Type HPE 41/22

color: black

Type HPE 63/63

Type HPE

Type HPE 41/41

Type HPE 41/22

HALFEN Channel

for example;

HM 52/34

The channel cover PAis used to prevent dirt entering the continuous channel opening.Assembly diagram

Channel end caps, HPE

Channel cover PA

0.650




Cant i levers

Flexible comprehensive support system

Short assembly times

Heavy duty framing system Medium duty framing system Light duty framing system

The flexibility of HALFEN cantilevers

and T-bolts makes them ideal when

the exact positions and sizes of

supports are not finalized at the plann-

ing stage of a project.

Using the HALFEN product range

avoids costly and complex adjustment

work, drilling or thread cutting, in

components which may already be

corrosion protected.

Whether for low or very high perfor-

mance requirements, you are guaran-

teed to find an effective solution in the

HALFEN product range. Using adjustable

bolt connections, components can be in-

stalled, dismantled, moved and adjusted

quickly and simply.

Pipe supports with cantilever brackets in a sewage treatment plant

Note: Depending on the number of

items ordered, custom cantilevers are

available

Canti levers KON

KON 28/1

KON 36/1

KON 36/2

KON 41/1

KON 41/D

KON 41/2

KON 52/2

You can find detailed information on cantilevers in our catalogue;

Adjustable Framing constructions: "HALFEN Adjustable framing

construction systems product information, MT-FFC".



HALFEN Channels Heavy Duty Framing Systems Medium Duty Framing Systems Light Duty Framing Systems

Type:

Order code Pages 1226 Pages 2735Pages 3643

WBhot-rolled:

Material to ASTM A 283, Gr.D

cold-rolled:Material to ASTM A 283, Gr.C

mill finish

Type HZM: to ASTM A 283, Gr.D

Material

Date post:	07-Aug-2018
Category:	Documents
Upload:	corui-mihai-valer
View:	218 times
Download:	0 times

Halfen Mt Fbc Us

Documents