2.80TT

0

3.500

10

14

4.500

SECTION T-TSCALE 8 : 1

REVISIONSZONE REV DESCRIPTION APPROVED DATE

1.0 INITIAL DESIGN

DO NOT SCALE DRAWING1.DIMS & TOLERANCES APPLY AFTER FINISH PER ANSI/ASME Y14.5 - 20092.DIMS INSIDE ARE FOR INSPECTION & DIMS INSIDE ( ) ARE FOR REFERENCE.3.BREAK ALL EDGES, REMOVE BURRS & FOREIGN MATTER.4.NOT ALL DIMS WILL BE SHOWN FOR PARTS MANUFACTURED USING CAD DATA5.SURFACE ROUGHNESS SHALL BE 125 Ra 6.PART SUBSTITUTIONS ARE ACCEPTED WITH THE APPROVAL OF NEURALYNX.7.PACKAGING SHALL INCLUDE PART #, REV #, AND TITLE/DESCRIPTION.8.ALL INSPECTION DIMENSIONS & CALLOUTS SHALL BE TESTED PER THIS 9.DRAWING. PART DELIVERY SHALL INCLUDE INSPECTION RESULTS. NEURALYNX SHALL BE NOTIFIED OF NON-COMPLIANT PARTS AND HAVE DISCRETION IN THE USE OF NON-COMPLIANT PARTS.

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1

E

F

E

F

A

UNLESS OTHERWISE SPECIFIED

THIS DOCUMENT IS THE PROPERTY OF NEURALYNX. THE CONTENTS OF THIS DOCUMENT ARE CONFIDENTIAL AND CONSTITUTE TRADE SECRETS PROPRIETARY TO NEURALYNX. NEITHER THIS DOCUMENT NOR ITS CONTENTS SHALL BE DISCLOSED TO ANY UNAUTHORIZED PERSON, COPIED OR PUBLISHED WITHOUT THE PRIOR WRITTEN CONSENT OF NEURALYNX.

SHEET1 OF 1

WEIGHT0.00 LBS

SCALE4:1

TITLE:

SIZE REVPART NO.

A 1.029-0206-0003-A

PART, MACH, COVER, EXIT CAP, 18 TT MICRODRIVE, STANDARD

= .5= 1 = 0.1 = 0.02 = 0.005= 0.0005 105 COMMERCIAL DR. BOZEMAN, MT 59715 (406) 585-4542

ANGXX.XX.XXX.XXXX.XXXX

3RD ANGLE

MATERIAL: FINISH: ENGINEER

DATEDelrin 2700 NC010, Low Viscosity Acetal Copolymer (SS)

NONEVOLUME

0.02 CUBIC IN

PROPRIETARY:

INSPECT1:BATCH PARTS

ENGINEER

DATE

INCHES (mm)

3.100

2.24

1.46

20.00°40.00°

60.00°

REVISIONSZONE REV DESCRIPTION APPROVED DATE

1.0 INITIAL DESIGN

DO NOT SCALE DRAWING1.DIMS & TOLERANCES APPLY AFTER FINISH PER ANSI/ASME Y14.5 - 20092.DIMS INSIDE ARE FOR INSPECTION & DIMS INSIDE ( ) ARE FOR REFERENCE.3.BREAK ALL EDGES, REMOVE BURRS & FOREIGN MATTER.4.NOT ALL DIMS WILL BE SHOWN FOR PARTS MANUFACTURED USING CAD DATA5.SURFACE ROUGHNESS SHALL BE 125 Ra 6.PART SUBSTITUTIONS ARE ACCEPTED WITH THE APPROVAL OF NEURALYNX.7.PACKAGING SHALL INCLUDE PART #, REV #, AND TITLE/DESCRIPTION.8.ALL INSPECTION DIMENSIONS & CALLOUTS SHALL BE TESTED PER THIS 9.DRAWING. PART DELIVERY SHALL INCLUDE INSPECTION RESULTS. NEURALYNX SHALL BE NOTIFIED OF NON-COMPLIANT PARTS AND HAVE DISCRETION IN THE USE OF NON-COMPLIANT PARTS.

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1

E

F

E

F

A

UNLESS OTHERWISE SPECIFIED

THIS DOCUMENT IS THE PROPERTY OF NEURALYNX. THE CONTENTS OF THIS DOCUMENT ARE CONFIDENTIAL AND CONSTITUTE TRADE SECRETS PROPRIETARY TO NEURALYNX. NEITHER THIS DOCUMENT NOR ITS CONTENTS SHALL BE DISCLOSED TO ANY UNAUTHORIZED PERSON, COPIED OR PUBLISHED WITHOUT THE PRIOR WRITTEN CONSENT OF NEURALYNX.

SHEET1 OF 1

WEIGHT0.54 LBS

SCALE4:1

TITLE:

SIZE REVPART NO.

A 1.0XX-XXXX-XXXX

NEW PART

= .5= 1 = 0.1 = 0.02 = 0.005= 0.0005 105 COMMERCIAL DR. BOZEMAN, MT 59715 (406) 585-4542

ANGXX.XX.XXX.XXXX.XXXX

3RD ANGLE

MATERIAL: FINISH: ENGINEER

DATEDelrin 2700 NC010, Low Viscosity Acetal Copolymer (SS)

NONEVOLUME

384.63 CUBIC IN

PROPRIETARY:

INSPECT1:BATCH PARTS

ENGINEER

DATE

INCHES (mm)

2.80

0.25

0.44

REVISIONSZONE REV DESCRIPTION APPROVED DATE

1.0 INITIAL DESIGN

DO NOT SCALE DRAWING1.DIMS & TOLERANCES APPLY AFTER FINISH PER ANSI/ASME Y14.5 - 20092.DIMS INSIDE ARE FOR INSPECTION & DIMS INSIDE ( ) ARE FOR REFERENCE.3.BREAK ALL EDGES, REMOVE BURRS & FOREIGN MATTER.4.NOT ALL DIMS WILL BE SHOWN FOR PARTS MANUFACTURED USING CAD DATA5.SURFACE ROUGHNESS SHALL BE 125 Ra 6.PART SUBSTITUTIONS ARE ACCEPTED WITH THE APPROVAL OF NEURALYNX.7.PACKAGING SHALL INCLUDE PART #, REV #, AND TITLE/DESCRIPTION.8.ALL INSPECTION DIMENSIONS & CALLOUTS SHALL BE TESTED PER THIS 9.DRAWING. PART DELIVERY SHALL INCLUDE INSPECTION RESULTS. NEURALYNX SHALL BE NOTIFIED OF NON-COMPLIANT PARTS AND HAVE DISCRETION IN THE USE OF NON-COMPLIANT PARTS.

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1

E

F

E

F

A

UNLESS OTHERWISE SPECIFIED

THIS DOCUMENT IS THE PROPERTY OF NEURALYNX. THE CONTENTS OF THIS DOCUMENT ARE CONFIDENTIAL AND CONSTITUTE TRADE SECRETS PROPRIETARY TO NEURALYNX. NEITHER THIS DOCUMENT NOR ITS CONTENTS SHALL BE DISCLOSED TO ANY UNAUTHORIZED PERSON, COPIED OR PUBLISHED WITHOUT THE PRIOR WRITTEN CONSENT OF NEURALYNX.

SHEET1 OF 1

WEIGHT0.00 LBS

SCALE4:1

TITLE:

SIZE REVPART NO.

A 1.029-0206-0003-A

PART, MACH, COVER, EXIT CAP, 18 TT MICRODRIVE, STANDARD

= .5= 1 = 0.1 = 0.02 = 0.005= 0.0005 105 COMMERCIAL DR. BOZEMAN, MT 59715 (406) 585-4542

ANGXX.XX.XXX.XXXX.XXXX

3RD ANGLE

MATERIAL: FINISH: ENGINEER

DATEDelrin 2700 NC010, Low Viscosity Acetal Copolymer (SS)

NONEVOLUME

0.02 CUBIC IN

PROPRIETARY:

INSPECT1:BATCH PARTS

ENGINEER

DATE

INCHES (mm)

2.30

0.15

0.44

0.25

REVISIONSZONE REV DESCRIPTION APPROVED DATE

1.0 INITIAL DESIGN

DO NOT SCALE DRAWING1.DIMS & TOLERANCES APPLY AFTER FINISH PER ANSI/ASME Y14.5 - 20092.DIMS INSIDE ARE FOR INSPECTION & DIMS INSIDE ( ) ARE FOR REFERENCE.3.BREAK ALL EDGES, REMOVE BURRS & FOREIGN MATTER.4.NOT ALL DIMS WILL BE SHOWN FOR PARTS MANUFACTURED USING CAD DATA5.SURFACE ROUGHNESS SHALL BE 125 Ra 6.PART SUBSTITUTIONS ARE ACCEPTED WITH THE APPROVAL OF NEURALYNX.7.PACKAGING SHALL INCLUDE PART #, REV #, AND TITLE/DESCRIPTION.8.ALL INSPECTION DIMENSIONS & CALLOUTS SHALL BE TESTED PER THIS 9.DRAWING. PART DELIVERY SHALL INCLUDE INSPECTION RESULTS. NEURALYNX SHALL BE NOTIFIED OF NON-COMPLIANT PARTS AND HAVE DISCRETION IN THE USE OF NON-COMPLIANT PARTS.

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1

E

F

E

F

A

UNLESS OTHERWISE SPECIFIED

THIS DOCUMENT IS THE PROPERTY OF NEURALYNX. THE CONTENTS OF THIS DOCUMENT ARE CONFIDENTIAL AND CONSTITUTE TRADE SECRETS PROPRIETARY TO NEURALYNX. NEITHER THIS DOCUMENT NOR ITS CONTENTS SHALL BE DISCLOSED TO ANY UNAUTHORIZED PERSON, COPIED OR PUBLISHED WITHOUT THE PRIOR WRITTEN CONSENT OF NEURALYNX.

SHEET1 OF 1

WEIGHT0.53 LBS

SCALE4:1

TITLE:

SIZE REVPART NO.

A 1.029-0206-0003-A

PART, MACH, COVER, EXIT CAP, 18 TT MICRODRIVE, STANDARD

= .5= 1 = 0.1 = 0.02 = 0.005= 0.0005 105 COMMERCIAL DR. BOZEMAN, MT 59715 (406) 585-4542

ANGXX.XX.XXX.XXXX.XXXX

3RD ANGLE

MATERIAL: FINISH: ENGINEER

DATEDelrin 2700 NC010, Low Viscosity Acetal Copolymer (SS)

NONEVOLUME

377.36 CUBIC IN

PROPRIETARY:

INSPECT1:BATCH PARTS

ENGINEER

DATE

INCHES (mm)

2.30

SCALE 8 : 1

40.00°

1.46

REVISIONSZONE REV DESCRIPTION APPROVED DATE

1.0 INITIAL DESIGN

DO NOT SCALE DRAWING1.DIMS & TOLERANCES APPLY AFTER FINISH PER ANSI/ASME Y14.5 - 20092.DIMS INSIDE ARE FOR INSPECTION & DIMS INSIDE ( ) ARE FOR REFERENCE.3.BREAK ALL EDGES, REMOVE BURRS & FOREIGN MATTER.4.NOT ALL DIMS WILL BE SHOWN FOR PARTS MANUFACTURED USING CAD DATA5.SURFACE ROUGHNESS SHALL BE 125 Ra 6.PART SUBSTITUTIONS ARE ACCEPTED WITH THE APPROVAL OF NEURALYNX.7.PACKAGING SHALL INCLUDE PART #, REV #, AND TITLE/DESCRIPTION.8.ALL INSPECTION DIMENSIONS & CALLOUTS SHALL BE TESTED PER THIS 9.DRAWING. PART DELIVERY SHALL INCLUDE INSPECTION RESULTS. NEURALYNX SHALL BE NOTIFIED OF NON-COMPLIANT PARTS AND HAVE DISCRETION IN THE USE OF NON-COMPLIANT PARTS.

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1

E

F

E

F

A

UNLESS OTHERWISE SPECIFIED

THIS DOCUMENT IS THE PROPERTY OF NEURALYNX. THE CONTENTS OF THIS DOCUMENT ARE CONFIDENTIAL AND CONSTITUTE TRADE SECRETS PROPRIETARY TO NEURALYNX. NEITHER THIS DOCUMENT NOR ITS CONTENTS SHALL BE DISCLOSED TO ANY UNAUTHORIZED PERSON, COPIED OR PUBLISHED WITHOUT THE PRIOR WRITTEN CONSENT OF NEURALYNX.

SHEET1 OF 2

WEIGHT0.53 LBS

SCALE2:1

TITLE:

SIZE REVPART NO.

A 1.0XX-XXXX-XXXX

NEW PART

= .5= 1 = 0.1 = 0.02 = 0.005= 0.0005 105 COMMERCIAL DR. BOZEMAN, MT 59715 (406) 585-4542

ANGXX.XX.XXX.XXXX.XXXX

3RD ANGLE

MATERIAL: FINISH: ENGINEER

DATEDelrin 2700 NC010, Low Viscosity Acetal Copolymer (SS)

NONEVOLUME

375.30 CUBIC IN

PROPRIETARY:

INSPECT1:BATCH PARTS

ENGINEER

DATE

INCHES (mm)

2.502.50

2.30 2.30

SCALE 8 : 1

REVISIONSZONE REV DESCRIPTION APPROVED DATE

1.0 INITIAL DESIGN

DO NOT SCALE DRAWING1.DIMS & TOLERANCES APPLY AFTER FINISH PER ANSI/ASME Y14.5 - 20092.DIMS INSIDE ARE FOR INSPECTION & DIMS INSIDE ( ) ARE FOR REFERENCE.3.BREAK ALL EDGES, REMOVE BURRS & FOREIGN MATTER.4.NOT ALL DIMS WILL BE SHOWN FOR PARTS MANUFACTURED USING CAD DATA5.SURFACE ROUGHNESS SHALL BE 125 Ra 6.PART SUBSTITUTIONS ARE ACCEPTED WITH THE APPROVAL OF NEURALYNX.7.PACKAGING SHALL INCLUDE PART #, REV #, AND TITLE/DESCRIPTION.8.ALL INSPECTION DIMENSIONS & CALLOUTS SHALL BE TESTED PER THIS 9.DRAWING. PART DELIVERY SHALL INCLUDE INSPECTION RESULTS. NEURALYNX SHALL BE NOTIFIED OF NON-COMPLIANT PARTS AND HAVE DISCRETION IN THE USE OF NON-COMPLIANT PARTS.

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1

E

F

E

F

A

UNLESS OTHERWISE SPECIFIED

THIS DOCUMENT IS THE PROPERTY OF NEURALYNX. THE CONTENTS OF THIS DOCUMENT ARE CONFIDENTIAL AND CONSTITUTE TRADE SECRETS PROPRIETARY TO NEURALYNX. NEITHER THIS DOCUMENT NOR ITS CONTENTS SHALL BE DISCLOSED TO ANY UNAUTHORIZED PERSON, COPIED OR PUBLISHED WITHOUT THE PRIOR WRITTEN CONSENT OF NEURALYNX.

SHEET1 OF 3

WEIGHT0.66 LBS

SCALE4:1

TITLE:

SIZE REVPART NO.

A 1.0XX-XXXX-XXXX

NEW PART

= .5= 1 = 0.1 = 0.02 = 0.005= 0.0005 105 COMMERCIAL DR. BOZEMAN, MT 59715 (406) 585-4542

ANGXX.XX.XXX.XXXX.XXXX

3RD ANGLE

MATERIAL: FINISH: ENGINEER

DATEDelrin 2700 NC010, Low Viscosity Acetal Copolymer (SS)

NONEVOLUME

469.97 CUBIC IN

PROPRIETARY:

INSPECT1:BATCH PARTS

ENGINEER

DATE

INCHES (mm)

29-0206-0008-A2 chimney 8 tetrode each 1 reference each

29-0206-0003-C16 tetrode 1 reference1 fiber

29-0206-0003-D8 tetrode 1 reference1 fiber

29-0206-0003-B8 tetrode 1 reference

29-0206-0003-A16 tetrode 1 reference

neuralynx.com

Halo-18 Microdrive --- Exit Tip Designs

CUSTOM EXIT TIPS

advanced electrophysiology solutionssales@neuralynx.com - Bozeman, Montana

sales@neuralynxeurope.com - Dublin, Ireland

R ExitTips 05/16 rev. 1.0

STANDARD EXIT TIPS

2.502.50

2.30 2.30RR

SCALE 8 : 1

0

3.504.50

10

14

SECTION R-RSCALE 8 : 1

REVISIONSZONE REV DESCRIPTION APPROVED DATE

1.0 INITIAL DESIGN

DO NOT SCALE DRAWING1.DIMS & TOLERANCES APPLY AFTER FINISH PER ANSI/ASME Y14.5 - 20092.DIMS INSIDE ARE FOR INSPECTION & DIMS INSIDE ( ) ARE FOR REFERENCE.3.BREAK ALL EDGES, REMOVE BURRS & FOREIGN MATTER.4.NOT ALL DIMS WILL BE SHOWN FOR PARTS MANUFACTURED USING CAD DATA5.SURFACE ROUGHNESS SHALL BE 125 Ra 6.PART SUBSTITUTIONS ARE ACCEPTED WITH THE APPROVAL OF NEURALYNX.7.PACKAGING SHALL INCLUDE PART #, REV #, AND TITLE/DESCRIPTION.8.ALL INSPECTION DIMENSIONS & CALLOUTS SHALL BE TESTED PER THIS 9.DRAWING. PART DELIVERY SHALL INCLUDE INSPECTION RESULTS. NEURALYNX SHALL BE NOTIFIED OF NON-COMPLIANT PARTS AND HAVE DISCRETION IN THE USE OF NON-COMPLIANT PARTS.

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1

E

F

E

F

A

UNLESS OTHERWISE SPECIFIED

THIS DOCUMENT IS THE PROPERTY OF NEURALYNX. THE CONTENTS OF THIS DOCUMENT ARE CONFIDENTIAL AND CONSTITUTE TRADE SECRETS PROPRIETARY TO NEURALYNX. NEITHER THIS DOCUMENT NOR ITS CONTENTS SHALL BE DISCLOSED TO ANY UNAUTHORIZED PERSON, COPIED OR PUBLISHED WITHOUT THE PRIOR WRITTEN CONSENT OF NEURALYNX.

SHEET1 OF 2

WEIGHT0.66 LBS

SCALE4:1

TITLE:

SIZE REVPART NO.

A 1.0XX-XXXX-XXXX

NEW PART

= .5= 1 = 0.1 = 0.02 = 0.005= 0.0005 105 COMMERCIAL DR. BOZEMAN, MT 59715 (406) 585-4542

ANGXX.XX.XXX.XXXX.XXXX

3RD ANGLE

MATERIAL: FINISH: ENGINEER

DATEDelrin 2700 NC010, Low Viscosity Acetal Copolymer (SS)

NONEVOLUME

469.97 CUBIC IN

PROPRIETARY:

INSPECT1:BATCH PARTS

ENGINEER

DATE

INCHES (mm)

EXIT TIP DESIGNS

SCALE 4 : 1

REVISIONSZONE REV DESCRIPTION APPROVED DATE

1.0 INITIAL DESIGN

DO NOT SCALE DRAWING1.DIMS & TOLERANCES APPLY AFTER FINISH PER ANSI/ASME Y14.5 - 20092.DIMS INSIDE ARE FOR INSPECTION & DIMS INSIDE ( ) ARE FOR REFERENCE.3.BREAK ALL EDGES, REMOVE BURRS & FOREIGN MATTER.4.NOT ALL DIMS WILL BE SHOWN FOR PARTS MANUFACTURED USING CAD DATA5.SURFACE ROUGHNESS SHALL BE 125 Ra 6.PART SUBSTITUTIONS ARE ACCEPTED WITH THE APPROVAL OF NEURALYNX.7.PACKAGING SHALL INCLUDE PART #, REV #, AND TITLE/DESCRIPTION.8.ALL INSPECTION DIMENSIONS & CALLOUTS SHALL BE TESTED PER THIS 9.DRAWING. PART DELIVERY SHALL INCLUDE INSPECTION RESULTS. NEURALYNX SHALL BE NOTIFIED OF NON-COMPLIANT PARTS AND HAVE DISCRETION IN THE USE OF NON-COMPLIANT PARTS.

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1

E

F

E

F

A

UNLESS OTHERWISE SPECIFIED

THIS DOCUMENT IS THE PROPERTY OF NEURALYNX. THE CONTENTS OF THIS DOCUMENT ARE CONFIDENTIAL AND CONSTITUTE TRADE SECRETS PROPRIETARY TO NEURALYNX. NEITHER THIS DOCUMENT NOR ITS CONTENTS SHALL BE DISCLOSED TO ANY UNAUTHORIZED PERSON, COPIED OR PUBLISHED WITHOUT THE PRIOR WRITTEN CONSENT OF NEURALYNX.

SHEET1 OF 1

WEIGHT0.02 LBS

SCALE1:1

TITLE:

SIZE REVPART NO.

A 1.0XX-XXXX-XXXX

NEW ASSEMBLY

= .5= 1 = 0.1 = 0.02 = 0.005= 0.0005 105 COMMERCIAL DR. BOZEMAN, MT 59715 (406) 585-4542

ANGXX.XX.XXX.XXXX.XXXX

3RD ANGLE

MATERIAL: FINISH: ENGINEER

DATENA NONEVOLUME

NA CUBIC IN

PROPRIETARY:

INSPECT1:BATCH PARTS

ENGINEER

DATE

INCHES (mm)

16 tetrode1 reference

Halo-18 Microdrive --- Exit Tip Alignment & Reference29-0206-0003-A

go to

2.80

0.25

0.44

REVISIONSZONE REV DESCRIPTION APPROVED DATE

1.0 INITIAL DESIGN

DO NOT SCALE DRAWING1.DIMS & TOLERANCES APPLY AFTER FINISH PER ANSI/ASME Y14.5 - 20092.DIMS INSIDE ARE FOR INSPECTION & DIMS INSIDE ( ) ARE FOR REFERENCE.3.BREAK ALL EDGES, REMOVE BURRS & FOREIGN MATTER.4.NOT ALL DIMS WILL BE SHOWN FOR PARTS MANUFACTURED USING CAD DATA5.SURFACE ROUGHNESS SHALL BE 125 Ra 6.PART SUBSTITUTIONS ARE ACCEPTED WITH THE APPROVAL OF NEURALYNX.7.PACKAGING SHALL INCLUDE PART #, REV #, AND TITLE/DESCRIPTION.8.ALL INSPECTION DIMENSIONS & CALLOUTS SHALL BE TESTED PER THIS 9.DRAWING. PART DELIVERY SHALL INCLUDE INSPECTION RESULTS. NEURALYNX SHALL BE NOTIFIED OF NON-COMPLIANT PARTS AND HAVE DISCRETION IN THE USE OF NON-COMPLIANT PARTS.

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1

E

F

E

F

A

UNLESS OTHERWISE SPECIFIED

THIS DOCUMENT IS THE PROPERTY OF NEURALYNX. THE CONTENTS OF THIS DOCUMENT ARE CONFIDENTIAL AND CONSTITUTE TRADE SECRETS PROPRIETARY TO NEURALYNX. NEITHER THIS DOCUMENT NOR ITS CONTENTS SHALL BE DISCLOSED TO ANY UNAUTHORIZED PERSON, COPIED OR PUBLISHED WITHOUT THE PRIOR WRITTEN CONSENT OF NEURALYNX.

SHEET1 OF 1

WEIGHT0.00 LBS

SCALE4:1

TITLE:

SIZE REVPART NO.

A 1.029-0206-0003-A

PART, MACH, COVER, EXIT CAP, 18 TT MICRODRIVE, STANDARD

= .5= 1 = 0.1 = 0.02 = 0.005= 0.0005 105 COMMERCIAL DR. BOZEMAN, MT 59715 (406) 585-4542

ANGXX.XX.XXX.XXXX.XXXX

3RD ANGLE

MATERIAL: FINISH: ENGINEER

DATEDelrin 2700 NC010, Low Viscosity Acetal Copolymer (SS)

NONEVOLUME

0.02 CUBIC IN

PROPRIETARY:

INSPECT1:BATCH PARTS

ENGINEER

DATE

INCHES (mm)

EXIT TIP DESIGNS

16 tetrode1 reference

Halo-18 Microdrive --- Exit Tip Detail29-0206-0003-A

go to

EXIT TIP DESIGNS

SCALE 4 : 1

REVISIONSZONE REV DESCRIPTION APPROVED DATE

1.0 INITIAL DESIGN

DO NOT SCALE DRAWING1.DIMS & TOLERANCES APPLY AFTER FINISH PER ANSI/ASME Y14.5 - 20092.DIMS INSIDE ARE FOR INSPECTION & DIMS INSIDE ( ) ARE FOR REFERENCE.3.BREAK ALL EDGES, REMOVE BURRS & FOREIGN MATTER.4.NOT ALL DIMS WILL BE SHOWN FOR PARTS MANUFACTURED USING CAD DATA5.SURFACE ROUGHNESS SHALL BE 125 Ra 6.PART SUBSTITUTIONS ARE ACCEPTED WITH THE APPROVAL OF NEURALYNX.7.PACKAGING SHALL INCLUDE PART #, REV #, AND TITLE/DESCRIPTION.8.ALL INSPECTION DIMENSIONS & CALLOUTS SHALL BE TESTED PER THIS 9.DRAWING. PART DELIVERY SHALL INCLUDE INSPECTION RESULTS. NEURALYNX SHALL BE NOTIFIED OF NON-COMPLIANT PARTS AND HAVE DISCRETION IN THE USE OF NON-COMPLIANT PARTS.

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1

E

F

E

F

A

UNLESS OTHERWISE SPECIFIED

THIS DOCUMENT IS THE PROPERTY OF NEURALYNX. THE CONTENTS OF THIS DOCUMENT ARE CONFIDENTIAL AND CONSTITUTE TRADE SECRETS PROPRIETARY TO NEURALYNX. NEITHER THIS DOCUMENT NOR ITS CONTENTS SHALL BE DISCLOSED TO ANY UNAUTHORIZED PERSON, COPIED OR PUBLISHED WITHOUT THE PRIOR WRITTEN CONSENT OF NEURALYNX.

SHEET1 OF 1

WEIGHT0.02 LBS

SCALE1:1

TITLE:

SIZE REVPART NO.

A 1.0XX-XXXX-XXXX

NEW ASSEMBLY

= .5= 1 = 0.1 = 0.02 = 0.005= 0.0005 105 COMMERCIAL DR. BOZEMAN, MT 59715 (406) 585-4542

ANGXX.XX.XXX.XXXX.XXXX

3RD ANGLE

MATERIAL: FINISH: ENGINEER

DATENA NONEVOLUME

NA CUBIC IN

PROPRIETARY:

INSPECT1:BATCH PARTS

ENGINEER

DATE

INCHES (mm)

8 tetrode1 reference

Halo-18 Microdrive --- Exit Tip Alignment & Reference29-0206-0003-B

go to

2.30

0.15

0.44

0.25

REVISIONSZONE REV DESCRIPTION APPROVED DATE

1.0 INITIAL DESIGN

DO NOT SCALE DRAWING1.DIMS & TOLERANCES APPLY AFTER FINISH PER ANSI/ASME Y14.5 - 20092.DIMS INSIDE ARE FOR INSPECTION & DIMS INSIDE ( ) ARE FOR REFERENCE.3.BREAK ALL EDGES, REMOVE BURRS & FOREIGN MATTER.4.NOT ALL DIMS WILL BE SHOWN FOR PARTS MANUFACTURED USING CAD DATA5.SURFACE ROUGHNESS SHALL BE 125 Ra 6.PART SUBSTITUTIONS ARE ACCEPTED WITH THE APPROVAL OF NEURALYNX.7.PACKAGING SHALL INCLUDE PART #, REV #, AND TITLE/DESCRIPTION.8.ALL INSPECTION DIMENSIONS & CALLOUTS SHALL BE TESTED PER THIS 9.DRAWING. PART DELIVERY SHALL INCLUDE INSPECTION RESULTS. NEURALYNX SHALL BE NOTIFIED OF NON-COMPLIANT PARTS AND HAVE DISCRETION IN THE USE OF NON-COMPLIANT PARTS.

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1

E

F

E

F

A

UNLESS OTHERWISE SPECIFIED

THIS DOCUMENT IS THE PROPERTY OF NEURALYNX. THE CONTENTS OF THIS DOCUMENT ARE CONFIDENTIAL AND CONSTITUTE TRADE SECRETS PROPRIETARY TO NEURALYNX. NEITHER THIS DOCUMENT NOR ITS CONTENTS SHALL BE DISCLOSED TO ANY UNAUTHORIZED PERSON, COPIED OR PUBLISHED WITHOUT THE PRIOR WRITTEN CONSENT OF NEURALYNX.

SHEET1 OF 1

WEIGHT0.53 LBS

SCALE4:1

TITLE:

SIZE REVPART NO.

A 1.029-0206-0003-A

PART, MACH, COVER, EXIT CAP, 18 TT MICRODRIVE, STANDARD

= .5= 1 = 0.1 = 0.02 = 0.005= 0.0005 105 COMMERCIAL DR. BOZEMAN, MT 59715 (406) 585-4542

ANGXX.XX.XXX.XXXX.XXXX

3RD ANGLE

MATERIAL: FINISH: ENGINEER

DATEDelrin 2700 NC010, Low Viscosity Acetal Copolymer (SS)

NONEVOLUME

377.36 CUBIC IN

PROPRIETARY:

INSPECT1:BATCH PARTS

ENGINEER

DATE

INCHES (mm)

EXIT TIP DESIGNS

Halo-18 Microdrive --- Exit Tip Detail

8 tetrode1 reference

29-0206-0003-B

go to

EXIT TIP DESIGNS

SCALE 4 : 1

REVISIONSZONE REV DESCRIPTION APPROVED DATE

1.0 INITIAL DESIGN

DO NOT SCALE DRAWING1.DIMS & TOLERANCES APPLY AFTER FINISH PER ANSI/ASME Y14.5 - 20092.DIMS INSIDE ARE FOR INSPECTION & DIMS INSIDE ( ) ARE FOR REFERENCE.3.BREAK ALL EDGES, REMOVE BURRS & FOREIGN MATTER.4.NOT ALL DIMS WILL BE SHOWN FOR PARTS MANUFACTURED USING CAD DATA5.SURFACE ROUGHNESS SHALL BE 125 Ra 6.PART SUBSTITUTIONS ARE ACCEPTED WITH THE APPROVAL OF NEURALYNX.7.PACKAGING SHALL INCLUDE PART #, REV #, AND TITLE/DESCRIPTION.8.ALL INSPECTION DIMENSIONS & CALLOUTS SHALL BE TESTED PER THIS 9.DRAWING. PART DELIVERY SHALL INCLUDE INSPECTION RESULTS. NEURALYNX SHALL BE NOTIFIED OF NON-COMPLIANT PARTS AND HAVE DISCRETION IN THE USE OF NON-COMPLIANT PARTS.

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1

E

F

E

F

A

UNLESS OTHERWISE SPECIFIED

THIS DOCUMENT IS THE PROPERTY OF NEURALYNX. THE CONTENTS OF THIS DOCUMENT ARE CONFIDENTIAL AND CONSTITUTE TRADE SECRETS PROPRIETARY TO NEURALYNX. NEITHER THIS DOCUMENT NOR ITS CONTENTS SHALL BE DISCLOSED TO ANY UNAUTHORIZED PERSON, COPIED OR PUBLISHED WITHOUT THE PRIOR WRITTEN CONSENT OF NEURALYNX.

SHEET1 OF 1

WEIGHT0.02 LBS

SCALE1:1

TITLE:

SIZE REVPART NO.

A 1.0XX-XXXX-XXXX

NEW ASSEMBLY

= .5= 1 = 0.1 = 0.02 = 0.005= 0.0005 105 COMMERCIAL DR. BOZEMAN, MT 59715 (406) 585-4542

ANGXX.XX.XXX.XXXX.XXXX

3RD ANGLE

MATERIAL: FINISH: ENGINEER

DATENA NONEVOLUME

NA CUBIC IN

PROPRIETARY:

INSPECT1:BATCH PARTS

ENGINEER

DATE

INCHES (mm)

16 tetrode1 reference1 fiber

Halo-18 Microdrive --- Exit Tip Alignment & Reference29-0206-0003-C

go to

3.100

2.24

1.46

20.00°40.00°

60.00°

REVISIONSZONE REV DESCRIPTION APPROVED DATE

1.0 INITIAL DESIGN

DO NOT SCALE DRAWING1.DIMS & TOLERANCES APPLY AFTER FINISH PER ANSI/ASME Y14.5 - 20092.DIMS INSIDE ARE FOR INSPECTION & DIMS INSIDE ( ) ARE FOR REFERENCE.3.BREAK ALL EDGES, REMOVE BURRS & FOREIGN MATTER.4.NOT ALL DIMS WILL BE SHOWN FOR PARTS MANUFACTURED USING CAD DATA5.SURFACE ROUGHNESS SHALL BE 125 Ra 6.PART SUBSTITUTIONS ARE ACCEPTED WITH THE APPROVAL OF NEURALYNX.7.PACKAGING SHALL INCLUDE PART #, REV #, AND TITLE/DESCRIPTION.8.ALL INSPECTION DIMENSIONS & CALLOUTS SHALL BE TESTED PER THIS 9.DRAWING. PART DELIVERY SHALL INCLUDE INSPECTION RESULTS. NEURALYNX SHALL BE NOTIFIED OF NON-COMPLIANT PARTS AND HAVE DISCRETION IN THE USE OF NON-COMPLIANT PARTS.

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1

E

F

E

F

A

UNLESS OTHERWISE SPECIFIED

THIS DOCUMENT IS THE PROPERTY OF NEURALYNX. THE CONTENTS OF THIS DOCUMENT ARE CONFIDENTIAL AND CONSTITUTE TRADE SECRETS PROPRIETARY TO NEURALYNX. NEITHER THIS DOCUMENT NOR ITS CONTENTS SHALL BE DISCLOSED TO ANY UNAUTHORIZED PERSON, COPIED OR PUBLISHED WITHOUT THE PRIOR WRITTEN CONSENT OF NEURALYNX.

SHEET1 OF 1

WEIGHT0.54 LBS

SCALE4:1

TITLE:

SIZE REVPART NO.

A 1.0XX-XXXX-XXXX

NEW PART

= .5= 1 = 0.1 = 0.02 = 0.005= 0.0005 105 COMMERCIAL DR. BOZEMAN, MT 59715 (406) 585-4542

ANGXX.XX.XXX.XXXX.XXXX

3RD ANGLE

MATERIAL: FINISH: ENGINEER

DATEDelrin 2700 NC010, Low Viscosity Acetal Copolymer (SS)

NONEVOLUME

384.63 CUBIC IN

PROPRIETARY:

INSPECT1:BATCH PARTS

ENGINEER

DATE

INCHES (mm)

EXIT TIP DESIGNS

Halo-18 Microdrive --- Exit Tip Detail

16 tetrode1 reference1 fiber

29-0206-0003-C

go to

EXIT TIP DESIGNS

SCALE 4 : 1

REVISIONSZONE REV DESCRIPTION APPROVED DATE

1.0 INITIAL DESIGN

DO NOT SCALE DRAWING1.DIMS & TOLERANCES APPLY AFTER FINISH PER ANSI/ASME Y14.5 - 20092.DIMS INSIDE ARE FOR INSPECTION & DIMS INSIDE ( ) ARE FOR REFERENCE.3.BREAK ALL EDGES, REMOVE BURRS & FOREIGN MATTER.4.NOT ALL DIMS WILL BE SHOWN FOR PARTS MANUFACTURED USING CAD DATA5.SURFACE ROUGHNESS SHALL BE 125 Ra 6.PART SUBSTITUTIONS ARE ACCEPTED WITH THE APPROVAL OF NEURALYNX.7.PACKAGING SHALL INCLUDE PART #, REV #, AND TITLE/DESCRIPTION.8.ALL INSPECTION DIMENSIONS & CALLOUTS SHALL BE TESTED PER THIS 9.DRAWING. PART DELIVERY SHALL INCLUDE INSPECTION RESULTS. NEURALYNX SHALL BE NOTIFIED OF NON-COMPLIANT PARTS AND HAVE DISCRETION IN THE USE OF NON-COMPLIANT PARTS.

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1

E

F

E

F

A

UNLESS OTHERWISE SPECIFIED

THIS DOCUMENT IS THE PROPERTY OF NEURALYNX. THE CONTENTS OF THIS DOCUMENT ARE CONFIDENTIAL AND CONSTITUTE TRADE SECRETS PROPRIETARY TO NEURALYNX. NEITHER THIS DOCUMENT NOR ITS CONTENTS SHALL BE DISCLOSED TO ANY UNAUTHORIZED PERSON, COPIED OR PUBLISHED WITHOUT THE PRIOR WRITTEN CONSENT OF NEURALYNX.

SHEET1 OF 1

WEIGHT0.02 LBS

SCALE1:1

TITLE:

SIZE REVPART NO.

A 1.0XX-XXXX-XXXX

NEW ASSEMBLY

= .5= 1 = 0.1 = 0.02 = 0.005= 0.0005 105 COMMERCIAL DR. BOZEMAN, MT 59715 (406) 585-4542

ANGXX.XX.XXX.XXXX.XXXX

3RD ANGLE

MATERIAL: FINISH: ENGINEER

DATENA NONEVOLUME

NA CUBIC IN

PROPRIETARY:

INSPECT1:BATCH PARTS

ENGINEER

DATE

INCHES (mm)

8 tetrode1 reference1 fiber

Halo-18 Microdrive --- Exit Tip Alignment & Reference29-0206-0003-D

go to

2.30

SCALE 8 : 1

40.00°

1.46

REVISIONSZONE REV DESCRIPTION APPROVED DATE

1.0 INITIAL DESIGN

DO NOT SCALE DRAWING1.DIMS & TOLERANCES APPLY AFTER FINISH PER ANSI/ASME Y14.5 - 20092.DIMS INSIDE ARE FOR INSPECTION & DIMS INSIDE ( ) ARE FOR REFERENCE.3.BREAK ALL EDGES, REMOVE BURRS & FOREIGN MATTER.4.NOT ALL DIMS WILL BE SHOWN FOR PARTS MANUFACTURED USING CAD DATA5.SURFACE ROUGHNESS SHALL BE 125 Ra 6.PART SUBSTITUTIONS ARE ACCEPTED WITH THE APPROVAL OF NEURALYNX.7.PACKAGING SHALL INCLUDE PART #, REV #, AND TITLE/DESCRIPTION.8.ALL INSPECTION DIMENSIONS & CALLOUTS SHALL BE TESTED PER THIS 9.DRAWING. PART DELIVERY SHALL INCLUDE INSPECTION RESULTS. NEURALYNX SHALL BE NOTIFIED OF NON-COMPLIANT PARTS AND HAVE DISCRETION IN THE USE OF NON-COMPLIANT PARTS.

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1

E

F

E

F

A

UNLESS OTHERWISE SPECIFIED

THIS DOCUMENT IS THE PROPERTY OF NEURALYNX. THE CONTENTS OF THIS DOCUMENT ARE CONFIDENTIAL AND CONSTITUTE TRADE SECRETS PROPRIETARY TO NEURALYNX. NEITHER THIS DOCUMENT NOR ITS CONTENTS SHALL BE DISCLOSED TO ANY UNAUTHORIZED PERSON, COPIED OR PUBLISHED WITHOUT THE PRIOR WRITTEN CONSENT OF NEURALYNX.

SHEET1 OF 2

WEIGHT0.53 LBS

SCALE2:1

TITLE:

SIZE REVPART NO.

A 1.0XX-XXXX-XXXX

NEW PART

= .5= 1 = 0.1 = 0.02 = 0.005= 0.0005 105 COMMERCIAL DR. BOZEMAN, MT 59715 (406) 585-4542

ANGXX.XX.XXX.XXXX.XXXX

3RD ANGLE

MATERIAL: FINISH: ENGINEER

DATEDelrin 2700 NC010, Low Viscosity Acetal Copolymer (SS)

NONEVOLUME

375.30 CUBIC IN

PROPRIETARY:

INSPECT1:BATCH PARTS

ENGINEER

DATE

INCHES (mm)

EXIT TIP DESIGNS

Halo-18 Microdrive --- Exit Tip Detail

8 tetrode1 reference1 fiber

29-0206-0003-D

go to

EXIT TIP DESIGNS

SCALE 4 : 1

REVISIONSZONE REV DESCRIPTION APPROVED DATE

1.0 INITIAL DESIGN

DO NOT SCALE DRAWING1.DIMS & TOLERANCES APPLY AFTER FINISH PER ANSI/ASME Y14.5 - 20092.DIMS INSIDE ARE FOR INSPECTION & DIMS INSIDE ( ) ARE FOR REFERENCE.3.BREAK ALL EDGES, REMOVE BURRS & FOREIGN MATTER.4.NOT ALL DIMS WILL BE SHOWN FOR PARTS MANUFACTURED USING CAD DATA5.SURFACE ROUGHNESS SHALL BE 125 Ra 6.PART SUBSTITUTIONS ARE ACCEPTED WITH THE APPROVAL OF NEURALYNX.7.PACKAGING SHALL INCLUDE PART #, REV #, AND TITLE/DESCRIPTION.8.ALL INSPECTION DIMENSIONS & CALLOUTS SHALL BE TESTED PER THIS 9.DRAWING. PART DELIVERY SHALL INCLUDE INSPECTION RESULTS. NEURALYNX SHALL BE NOTIFIED OF NON-COMPLIANT PARTS AND HAVE DISCRETION IN THE USE OF NON-COMPLIANT PARTS.

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1

E

F

E

F

A

UNLESS OTHERWISE SPECIFIED

THIS DOCUMENT IS THE PROPERTY OF NEURALYNX. THE CONTENTS OF THIS DOCUMENT ARE CONFIDENTIAL AND CONSTITUTE TRADE SECRETS PROPRIETARY TO NEURALYNX. NEITHER THIS DOCUMENT NOR ITS CONTENTS SHALL BE DISCLOSED TO ANY UNAUTHORIZED PERSON, COPIED OR PUBLISHED WITHOUT THE PRIOR WRITTEN CONSENT OF NEURALYNX.

SHEET1 OF 1

WEIGHT0.02 LBS

SCALE1:1

TITLE:

SIZE REVPART NO.

A 1.0XX-XXXX-XXXX

NEW ASSEMBLY

= .5= 1 = 0.1 = 0.02 = 0.005= 0.0005 105 COMMERCIAL DR. BOZEMAN, MT 59715 (406) 585-4542

ANGXX.XX.XXX.XXXX.XXXX

3RD ANGLE

MATERIAL: FINISH: ENGINEER

DATENA NONEVOLUME

NA CUBIC IN

PROPRIETARY:

INSPECT1:BATCH PARTS

ENGINEER

DATE

INCHES (mm)

2 chimney8 tetrode each1 reference each

Halo-18 Microdrive --- Exit Tip Alignment & Reference29-0206-0008-A

go to

0.13

0.25

0.44

2.50

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1

E

F

E

F

A

THIS DOCUMENT IS THE PROPERTY OF NEURALYNX. THE CONTENTS OF THIS DOCUMENT ARE CONFIDENTIAL AND CONSTITUTE TRADE SECRETS PROPRIETARY TO NEURALYNX. NEITHER THIS DOCUMENT NOR ITS CONTENTS SHALL BE DISCLOSED TO ANY UNAUTHORIZED PERSON, COPIED OR PUBLISHED WITHOUT THE PRIOR WRITTEN CONSENT OF NEURALYNX.

SHEET2 OF 2

WEIGHT0.66 LBS

SCALE4:1

SIZE REVPART NO.

A 1.0XX-XXXX-XXXXENGINEER

DATE

VOLUME469.97 CUBIC IN

PROPRIETARY:

INSPECT1:BATCH PARTS

ENGINEER

DATE

EXIT TIP DESIGNS

Halo-18 Microdrive --- Exit Tip Detail

2 chimney8 tetrode each1 reference each

go to

29-0206-0008-A