Home >Documents >Hamilton Beach 48464 Power Cord Replacement · PDF fileHamilton Beach 48464 Power Cord...

Hamilton Beach 48464 Power Cord Replacement · PDF fileHamilton Beach 48464 Power Cord...

Date post:26-Apr-2018
Category:
View:219 times
Download:5 times
Share this document with a friend
Transcript:
  • Hamilton Beach 48464 Power CordReplacement

    This guide will show you how to access the origin of the power cord. This is important tounderstand because once you know where the cord begins, you will be able to inspect the entire

    cord and check for damage.

    Written By: Michael Damico

    Hamilton Beach 48464 Power Cord Replacement

    iFixit CC BY-NC-SA www.iFixit.com Page 1 of 6

  • INTRODUCTION

    This guide show use how to get to the power cord. One might find this help when repairing/replacinga faulty cord.

    TOOLS:Phillips #2 Screwdriver (1)

    Crown Bolt #8 Steel Spanner (1)

    Hamilton Beach 48464 Power Cord Replacement

    iFixit CC BY-NC-SA www.iFixit.com Page 2 of 6

    http://www.ifixit.com/Tools/Phillips-2-Screwdriver/IF145-032http://www.homedepot.com/b/Screwdriver/Spanner/N-5yc1vZ1z0y9o2Z1z10x5z

  • Step 1 Base

    This is what the bottom cover willlook like. Flip the Brew Stationupside down to easily access thescrews.

    Step 2

    Using the Philips 2 Screwdriver, unscrew the three 8-mm screws labeled in a red outline.

    Using the Crown Bolt #8 Steel Spanner, unscrew the two 8-mm screws labeled in a orange outline.

    Hamilton Beach 48464 Power Cord Replacement

    iFixit CC BY-NC-SA www.iFixit.com Page 3 of 6

  • Step 3

    Carefully slide off the bottom driptray by sliding it out away from theBrew Station.

    Step 4

    Gently lift the base away from theBrew Station.

    Hamilton Beach 48464 Power Cord Replacement

    iFixit CC BY-NC-SA www.iFixit.com Page 4 of 6

  • Step 5 Power Cord

    Using the Philips 2 Screwdriver, unscrew the two 8-mm screws labeled in a red outline.

    Step 6

    Using the Philips 2 Screwdriver,unscrew the two 8-mm screwslabeled in a red outline. This willrelease the bracket that is holdingdown the large piece in the middle.

    Hamilton Beach 48464 Power Cord Replacement

    iFixit CC BY-NC-SA www.iFixit.com Page 5 of 6

  • To reassemble your device, follow these instructions in reverse order.

    This document was last generated on 2017-07-02 01:10:07 PM.

    Step 7

    Using one hand, gently lift the largesilver piece out of the base.

    The silver piece will still beconnected to the Brew Station, sohandy it with care.

    Using the Philips 2 Screwdriver,unscrew the two 8-mm screwslabeled in a red outline.

    Step 8

    Once the screw is out, gently lift thewhite circuit board out of the base.This will be where the power cordbegins, so you will now have accessto the full length of the cord.

    Hamilton Beach 48464 Power Cord Replacement

    iFixit CC BY-NC-SA www.iFixit.com Page 6 of 6

    Hamilton Beach 48464 Power Cord ReplacementWritten By: Michael DamicoINTRODUCTION

    TOOLS:Step 1 BaseStep 2Step 3Step 4Step 5 Power CordStep 6Step 7Step 8

Click here to load reader

Reader Image
Embed Size (px)
Recommended