508
PullsPages 512-517
HANDLES AND PULLS
Flush mount pull designs provide ergonomic grip without protruding hardware disrupting door, drawer, or panel surfaces.
 Concealed styles rotate outward to provide a fully accessible handgrip.
 All styles install easily in a single mounting hole
6767P2 P1 MP
1
509
Handles Page 518-522
P9B8 B8 P8B4
SOUTHCO® handles install quickly and easily to provide comfortable ergonomic grip points for opening enclosure doors or drawers, and for removing mounted panels.
 Available in a variety of styles and strength options
 A variety of standard lengths to provide the appropriate grip required for the size of the door, drawer, or rack
\
sou Lhos CONNECT • CREATE • INNOVATE
INFO CLIC
510
Other options available. For complete details on variety, part numbers, installation and specification, go to
ACTUAL SIZE
ACTUAL SIZE
www.southco.com/P2
Textured matte finish
R 1 (.040)
127.3 (5.01) Large P2
25.5(1.00)
82.5 (3.25) Small P2
35.8(1.41)
5.5 (.21)
R 1.5 (.06)
40(1.58)
1.8 (.07)Door thickness (see table)
17(.65)
87.5±0.3 (3.45±.01) Smaller P2
132±0.3 (5.20±.01) Larger P2
R Max.1.5 (.06)
30.7±0.15(1.210±.005)
Dimensions in millimeters (inch) unless otherwise stated
• Snap-in installation• 2 sizes
Material and FinishABS plastic, black
Performance DetailsMaximum static load: Lifting / pulling: 1300 N (300 lbf) Pushing / sliding: 450 N (100 lbf)
Flammability rating: UL94-HB or UL94-V0
Operating temperature range: -50°C (-60°F) to 60°C (140°F)
NotesPerformance details are based on installation in a 1.2 (.048) thick steel door. Maximum loads are limited by door strength.
P2 Flush PullLow profile · Lift or pull · Single hole mount
Small
Large
Door Thickness RangePart Number
Small Large
Min. Max. UL94-HB UL94-V0 UL94-HB UL94-V0
1.0 (.040) 1.4 (.055) P2-41 P2-41-1 P2-51 P2-51-1
1.4 (.055) 1.8 (.070) P2-42 P2-42-1 P2-52 P2-52-1
1.8 (.070) 2.1 (.085) P2-43 P2-43-1 P2-53 P2-53-1
2.1 (.085) 2.5 (.100) P2-44 P2-44-1 P2-54 P2-54-1
Part Number Selection _________________________________________________________________________________
>El
f
soulhco® CONNECT. CREATE • INNOVATE
511
Other options available. For complete details on variety, part numbers, installation and specification, go to
Dimensions in millimeters (inch) unless otherwise stated
www.southco.com/P2
Type B (Counter-Clockwise) Version Shown
P2 Flush Pull - LockableLow profile · Lift or pull · Single hole mount
110 +/- 0.3 (4.33 +/-0.012)
Door
Frame
11 +/- 0.3 (0.433 +/-0.012)
4x R 1.5(.06)30.7 +/- 0.3
(1.21 +/- 0.012)
• Snap-in installation• Lockable• Lock core included or sold separately• Cam sold separately
Material and FinishPull: ABS plastic, black
Lock parts: Zinc alloy, powder coated. Brass. Steel, zinc plated. Buna-N
Flammability Rating UL94-HB or UL94-VO (See table)
NotesFor pulls without lock core, lock core sold separately, see page 158.
Cam sold separately. See page 167.
Cam Forward Grip
Cam Reversed Grip
Cam Offset
25 (0.98) 25 (0.98) No Offset
21.8 (0.86) 28.2 (1.11) 3.2 (1.25)
18.6 (0.73) 31.4 (1.24) 6.4 (.250)
15.5 (0.61) 34.5 (1.36) 9.5 (.375)
116.2 (4.57)
Cam shownin lockedposition *
82.3 (3.24)
25.3 (1) 35.5 (1.4)
2 (0.08)Typical Wall Thickness
23 (0.91)Frame
Door
CamLength
Cam Grip
Cam forwardNo Offset
(Straight) CamCam reversed
Door Thickness (see table)
31.85 (1.25)
8.3 (0.33)
38.8(1.53)
* Cam Ordered Separately
For Cam Part Numbers and options see our Handbook page 167
or www.southco.com
P2 - 4 D M - R LL Lock Style
2 With lock core, keyed alike CH751 (with two flat keys supplied) 9 Without lock core (See our handbook page 183 or visit www.southco.com)
D Door Thickness Range1 1.0 (.040) - 1.4 (.055) 2 1.4 (.055) - 1.8 (.070)3 1.8 (.070) - 2.1 (.085)4 2.1 (.085) - 2.5 (.100)
R Rotation1 Type A (Clockwise to lock) 2 Type B (Counter-Clockwise to lock)
___________________________________________________________________________ Part Number Selection
M Material1 UL94-V0 PC/ABS 2 UL94-HB ABS
souLhco® CONNECT • CREATE • INNOVATE
512
Other options available. For complete details on variety, part numbers, installation and specification, go to
ACTUAL SIZE
www.southco.com/P1
25.5(1.00) 121.5 (4.78)
64.3(2.53)
46.7(1.84)
91.5 (3.60)
123 (4.84)
23 (.90)22.7(.89)
Pull
Cup2.5 (.09)
Door thickness (see table)
114.30±0.25(4.500±.010)
38±0.2(1.500±.005)
0.7 (.03) R Max.
Dimensions in millimeters (inch) unless otherwise stated
• Easy installation• Deep pocket
Material and FinishPull and cup: ABS plastic, black Screws: Steel, zinc plated
Performance DetailsMaximum static load: Lifting / pulling: 1300 N (300 lbf) Pushing / sliding: 450 N (100 lbf)
Flammability rating: UL94-HB or UL94-V0 (See table)
Operating temperature range: -50°C (-60°F) to 60°C (140°F)
Installation NotesMounting screws supplied. Door thickness less than the minimum for each range allows some movement of the pull. Maximum torque for mounting screws is 0.5 Nm (5 inlbf)
P1 Flush PullLow profile · Lift or pull · Single hole mount
Two No. 6 BT thread forming screws (supplied)
Door Thickness Range Part Number
Min. Max. UL94-HB UL94-V0
1.0 (.040) 1.8 (.070) P1-30-101-11 P1-31
1.8 (.070) 3.3 (.130) P1-30-103-11 P1-33
3.3 (.130) 4.8 (.190) P1-30-105-11 P1-35
4.8 (.190) 6.3 (.250) P1-30-107-11 P1-37
See table
Part Number
so.khAs9° CONNECT '
r-
-41
1_1
0- I
a
INFO CLIC
513
Other options available. For complete details on variety, part numbers, installation and specification, go to
ACTUAL SIZE
KNOB OVAL SQUARE ROUND
Oval flange Square flange Round flange
Tapped hole M4(8-32) x 10(.4) deep
Knob
Thru FlangeSection
33(1.30)
38(1.50)
34(1.34)
34(1.34)
Ø 33(1.30)
Ø 4.5 (.18)
1(.04)
17(.65)
Ø 18.8 (.74)
Ø 4.5 (.177)
Door thickness
Dimensions in millimeters (inch) unless otherwise stated
• Stylish knob design• Finish and flange shape flexibility
Material and FinishZinc alloy, plated or powder coated
Installation NotesScrews not supplied. Calculate screw length using the following formula: Door thickness + 6 (.25) Maximum tightening torque of mounting screws: 1.7 Nm (15 inlbf)
Style matches MP push-to-close latch on page 228
MP Point PullSurface mount
MP - 06 - 1 S - F
S Style10 Oval flange20 Square flange30 Round flange
MP - 06 - 1 S - F
S Style00 Imperial 8 -32 mounting hole40 Metric M4 mounting hole
Knob
Oval flange Square flange Round flange
Tapped hole M4(8-32) x 10(.4) deep
Knob
Thru FlangeSection
33(1.30)
38(1.50)
34(1.34)
34(1.34)
Ø 33(1.30)
Ø 4.5 (.18)
1(.04)
17(.65)
Ø 18.8 (.74)
Oval flange Square flange Round flange
www.southco.com/MP1
___________________________________________________________________________ Part Number Selection
___________________________________________________________________________ Part Number Selection
Knob Part Number
Flange Part Number
Choose knob separately
F Finish 10 Chrome, polished20 Chrome, satin30 Nickel, brushed40 Diamond brass50 Powder coated, black
F Finish 10 Chrome, polished20 Chrome, satin30 Nickel, brushed40 Diamond brass50 Powder coated, black
§§§
—
k I
ivrituttui lo
47-
INFO CLIC
s o u h os CONNECT • CREATE • INNOVATE
514
Other options available. For complete details on variety, part numbers, installation and specification, go to
ACTUAL SIZE40 Series
ACTUAL SIZE20 Series
ACTUAL SIZE10 Series
31(1.22)
2.5 (.09)
20.5(.81)
81(3.19)
Pull
34(1.34)
28.5(1.12)
Self tapping screws 16 (.63) long(2 screws supplied)
Max. panel thickness 6.4 (.25)
(with screws provided)
20.5 (.81)
14.3 (.56)
17.1 (.67)
14.3(.56)
Panel or door Ø 7.2(.28)
Bushings(2 supplied)
Top view of bushing
21(.83)
106(4.17)
14.3 (.56)
41.5 (1.63)
43.5 (1.72)
2.5(.09)
29.5(1.16)
20.5(.81)
14.3 (.56)
17.1 (.67)
Pull
Self tapping screws 16 (.63) long(2 screws supplied)
Max. panel thickness6.4 (.25) (with screws provided)
Black housing
Black housing
Ø 7.2(.28)
Bushings(2 supplied)
Top view of bushing
10 Series - Metal with Push Button Handle Release31(1.22)
2.5 (.09)20.5(.81)
81(3.19)
Pull
34(1.34)
28.5(1.12)
Self tapping screws 16 (.63) long(2 screws supplied)
Max. panel thickness 6.4 (.25)
(with screws provided)
20.5 (.81)
14.3 (.56)
17.1 (.67)
14.3(.56)
Panel or door Ø 7.2(.28)
Bushings(2 supplied)
Top view of bushing
Pull
Black housing
Max. panel thickness 6.4 (.25)
(with screws provided)
21.1(.83) 2.5 (.09) 14.3
(.56)
11.5(.45)
83.1(3.27)
Self tapping screws 16 (.63) long(2 screws supplied)
20.5 (.81)
14.3 (.56)
17.1 (.67)
Bushings(2 supplied)
Top view of bushing
Housing
Ø 7.2(.28)
Panel or door
32(1.27)
26(1.03)
Push button releasesspring-loaded handle
ACTUAL SIZE10 Series
Dimensions in millimeters (inch) unless otherwise stated
67 Concealed PullSurface mount
www.southco.com/67
• Flush mounting
Material and Finish10 series: Plastic, black or zinc alloy, black or silver 20 & 40 series: Handle: Aluminum, silver or black powder coated Housing and bushing: Plastic, black Screws: Stainless steel, passivated
Performance DetailsMaximum static load: 10 series: 620 N (140 lbf) - plastic 10 series: 1100 N (250 lbf) - metal 20 series: 440 N (100 lbf) 40 series: 580 N (130 lbf)
Flammability rating: Housing & bushing: UL94-HB Handle (10 Series plastic only): UL94-V2
Installation NotesThread forming screw (M4 x 0.7 (10 series metal) M4.2 x 1.4 (all other versions) ) supplied for door thickness 6.4 (.25) Maximum. For thicker doors calculate screw length using the following formula: Door thickness + 10 (.40)
NotesMaximum tightening torque of mounting screws: All versions except 10 series metal: 0.5 Nm (5 inlbf) 10 series metal version: 2.5 Nm (18 inlbf)
10 Series - Plastic
soulhco® CONNECT. CREATE • INNOVATE
11
515
Other options available. For complete details on variety, part numbers, installation and specification, go to
ACTUAL SIZE40 Series
ACTUAL SIZE20 Series
ACTUAL SIZE10 Series
ACTUAL SIZE40 Series
ACTUAL SIZE20 Series
ACTUAL SIZE10 Series
14.3 (.56)
58.5 (2.30)61 (2.40)
2.5 (.09)20.8(.82)
141(5.55)
Pull
29.5(1.16) 14.3 (.56)
17.1 (.67)
Ø 7.2(.28)
Max. panelthickness 6.4 (.25)
(with screws provided)
Black housing
Bushings(2 supplied)
Self tapping screws 16 (.63) long(2 screws supplied)
21(.83)
106(4.17)
14.3 (.56)
41.5 (1.63)
43.5 (1.72)
2.5(.09)
29.5(1.16)
20.5 (.81)
14.3 (.56)
17.1 (.67)
Pull
Self tapping screws 16 (.63) long(2 screws supplied)
Black housing
Ø 7.2(.28)
Bushings(2 supplied)
Top view of bushing
Full radius
A
Optional corner shape
16(.62±.01)
+0.0-0.5
Dimensions in millimeters (inch) unless otherwise stated
SeriesPart Number Installation
Silver Handle Black Handle A
10-Plastic ~ 67-10 76 (3.00 )
10-Metal 67-14 67-12 77.5 (3.05 )
20 67-27 67-25 102 (4.00 )
40 67-47 67-45 136 (5.35 )
+1.0 -.00+1.0 -.00
+1.0 -.00
+.04 -.00
+.04 -.00
+.04 -.00+.04 -.00
40 Series
Part NumberSee table
www.southco.com/67
20 Series
+1.0 -.00
INFO CLIC
kt
souLhco®
— 11111111M
warano-l: .1....
516
Other options available. For complete details on variety, part numbers, installation and specification, go to
ACTUAL SIZE
51(2.00)
20(.79)
203(8.00)
30(1.18)
150(5.91)
35(1.38)
Two slotted, thread formingscrews (suppliedwith rear install concealed only)
171.5±0.3(6.75±.01)
Ø 5.5±0.1 (.203±.005) (2 places)
Max. 19.0 (.75)
Supplied
Front Mount
171.5±0.3(6.75±.01)
For M5 or No. 10 screws(not supplied)Max. screw head Ø 10.5 (.41)
Ø 7.5±0.1(.295±.005)(2 places)
Dimensions in millimeters (inch) unless otherwise stated
• Front or rear concealed installation• Ergonomic, comfortable grip• High strength, light- weight solution
Material and FinishHandle: ABS plastic, black Screws: Steel, zinc plated
Performance DetailsMaximum static load: 775 N (175 lbf)
Flammability rating: UL94-HB
Operating temperature range: -40°C (-40°F) to 60°C (140°F)
Installation NotesMaximum tightening torque of screws: Rear install concealed only 4.0 Nm (35 inlbf)
NotesBulk packaged
www.southco.com/B8
B8 Grab HandleLarge · Surface mount
Part Number
Rear Install Concealed Front Install Concealed
B8-66-3 B8-63-3
Rear Install Concealed Front Install Concealed
mum mall gni
OMMUUDIC
soulhco® CONNECT. CREATE • INNOVATE
_— -
517
Other options available. For complete details on variety, part numbers, installation and specification, go to
ACTUAL SIZE
Two slotted, hex headscrew / lockwasherassemblies M6 x 32 (supplied with rear install concealed only)
95(3.74)
41(1.62)
27(1.07)
32(1.26)
150(5.91)
12.7 (.50)
Supplied
Max. 16.0 (.63)(with screws supplied)
111±0.1(4.37±.005)
6.6 (.26 )Ø +.010
-.000Handle
Snap-in cover
12.7 (.50)
111±0.1(4.37±.005)
+0.2-0.0
(2 places)
For M5 or No. 10 Screws (not supplied)Max. screw head Ø 10 (.39)
Ø 5.5±0.1 (.203±.005)(2 places)
Supplied
Max. 16.0 (.63)(with screws supplied)
111±0.1(4.37±.005)
6.6 (.26 )Ø +.010
-.000Handle
Snap-in cover
12.7 (.50)
111±0.1(4.37±.005)
+0.2-0.0
(2 places)
For M5 or No. 10 Screws (not supplied)Max. screw head Ø 10 (.39)
Ø 5.5±0.1 (.203±.005)(2 places)
Dimensions in millimeters (inch) unless otherwise stated
www.southco.com/B8
B8 Grab HandleSmall · Surface mount
Part NumberRear Install Concealed Front Install Concealed
B8-45-3 B8-43-3
Rear Install Concealed Front Install Concealed
• Front or rear concealed installation• Light-weight
Material and FinishHandle: ABS plastic, black Screws: Steel, zinc plated
Performance DetailsMaximum static load: 550 N (125 lbf)
Flammability rating: UL94-HB
Operating temperature range: -50°C (-60°F) to 60°C (140°F)
Installation NotesRear install concealed: M6 x 32 screw assembly supplied. Maximum tightening torque of screws: 4.0 Nm (35 inlbf). For door thickness greater than 16 (.63) calculate screw length using the following formula: Door thickness + 16 (.63)
NotesBulk packaged
A
L
rr (t1 r
Ilj
1
.
1
, , ,
sou L hos CONNECT • CREATE • INNOVATE
518
Other options available. For complete details on variety, part numbers, installation and specification, go to
ACTUAL SIZE
OVAL ACTUAL SIZE
±0.12 (±.005)
Ø 4.5±0.1 (.177±.004)(2 places)
C
Ø 8(.31)
15.9 (.625)
Round profileOval profile
Oval 38.1 (1.50)Round 31.0 (1.22)
10 (.39)
C
Dimensions in millimeters (inch) unless otherwise stated
• Two styles and color options available• Concealed installation• Four standard lengths
Material and FinishAluminum, anodized, clear or black
Performance DetailsMaximum working load: 1500 N (335 lbf)
Installation NotesScrews not supplied. Calculate screw length using the following formula: Door thickness + 5 (.20)
Maximum tightening torque of mounting screws: 1.7 Nm (15 inlbf)
www.southco.com/P8
P8 Grab HandleSurface mount
P8 - C - 31 - T - 1 F - PFor visual identification: M4 products have a counterbored hole. 8-32 products have a countersunk hole
Oval profile handles are currently offered in a 10-32 thread only.
C Centers030 30 (1.18) Hole centers064 64 (2.52) Hole centers096 96 (3.78) Hole centers128 128 (5.04) Hole centers
T Tapped mounting hole08 Imperial 8-32M4 Metric M4 x 0.7
FinishPart Number
C Bulk Packaged Individually Packaged (1 per bag)
Clear anodized P8-128-38-10V-11-3 P8-128-38-10V-11128 (5.04)
Black anodized P8-128-38-10V-15-3 P8-128-38-10V-15
Round Profile
Oval Profile
Part Number Selection
Part Number
P Packing optionOmit for individual packaging (1 per bag)3 Layer packaging contact Southco
F Finish1 Clear anodized5 Black anodized
111
soulhco® CONNECT. CREATE • INNOVATE
519
Other options available. For complete details on variety, part numbers, installation and specification, go to
ACTUAL SIZE
40(1.57)
13.3(.52)
Ø 12 (.47)
Roll PinBushing
5.5 (.22)
Base
Handle
90˚Ø 6.4 (.25)
C
40(1.57)
90˚
7(.27)
Ø 12 (.47)
14.6(.57)
Ø 6.4 (.25)
C
Base
Handle
Nut and lockwasher
Roll pinBushing
±0.12 (±.005)
Ø 4.5±0.1 (.177±.004)(2 places)
C
Dimensions in millimeters (inch) unless otherwise stated
P9 Grab HandleFolding · Surface mount
www.southco.com/P9
• Low profile folding style• Concealed installation• Anti-rattle friction feature
Material and FinishHandle and base: Aluminum, anodized, clear or black Roll pin, mounting nuts and lockwashers: Stainless steel passivated Bushing: Nylon
Performance DetailsMaximum static load: Internal threaded version 600 N (135 lbf) External thread version 400 N (90 lbf)
Installation NotesInternal thread: Screws not supplied. Calculate screw length using the following formula: Door thickness + 5 (.20)
Maximum tightening torque of mounting screws: 1.7 Nm (15 inlbf)
External thread: Maximum door thickness 8.4 (.33) Mounting nuts supplied. Maximum tightening torque of nuts: 11.5 Nm (10 inlbf)
P9 - C - 40 - T B - 1 F - P
P Packing optionOmit for individual packaging (1 per bag)3 Layer packaging contact Southco
F Finish1 Clear anodized5 Black anodized
B Base typeN Internal threadX External thread
C Centers040 40 (1.57) Hole centers064 64 (2.52) Hole centers096 96 (3.78) Hole centers128 128 (5.04) Hole centers
T Thread08 Imperial 8-32M4 Metric M4 x 0.7
Part Number SelectionFor visual identification: M4 products have a counterbored hole. 8-32 products have a countersunk hole
i A
souLhco®
a t
a
iP L
—f t
O
a
520
Other options available. For complete details on variety, part numbers, installation and specification, go to
EXTRA LARGE ACTUAL SIZE
MEDIUM ACTUAL SIZE
SMALL ACTUAL SIZE
LARGE ACTUAL SIZE
27(1.06)
9.5(.38)
63.5(2.50)
6.4 (.25)
28.5(1.13)
3.2 (.13)
28.5(1.13)
3 Holes,M4 x 0.7 orNo. 8-32 thread9.5 (.38) deep
27(1.06)
9.5(.38)
86(3.38)
6.4 (.25)
28.5(1.13)
3 Holes,M4 x 0.7 or No. 8-32 thread9.5 (.38) deep
3 Holes,M4 x 0.7 or No. 8-32 thread9.5 (.38) deep
51(2.00)
3.2 (.13)
27(1.06)
9.5(.38)
105(4.13)
6.4 (.25)
28.5(1.13)
70(2.75)
3.2 (.13)
27(1.06)
9.5(.38)
35(1.38)
6.4 (.25)
28.5(1.13)
3.2 (.13)
2 Holes,M4 x 0.7 or
No. 8-32 thread9.5 (.38) deep
Dimensions in millimeters (inch) unless otherwise stated
B4 HandleSurface mount
Medium
Extra Large
B4 - T - S 0 3 - 1 F - P
Part Number Selection _______________________________________________________________________________
P Packing optionOmit for individual packaging3 Layer packaged contact Southco
F Finish 1 Clear anodized5 Black anodized
• Easy concealed installation• Light-weight
Material and FinishAluminum, anodized, clear or black
Performance DetailsMaximum static load: 5560 N (1250 lbf)
Installation NotesScrews not supplied. Calculate screw length using the following formula: Door thickness + 9.5 (.38) Center screw may be eliminated if desired (Medium, Large, and Extra Large sizes only)
Maximum recommended tightening torque of mounting screws: 2.3 Nm (20 inlbf) (not supplied)
S Size1 Small 2 Medium3 Large4 Extra large
T Tapped mounting hole10 Imperial 8-3250 Metric M4 x 0.7
www.southco.com/B4