Basics IDE Drives - 1
IDE Drives
Intelligent drive electronics, IDE, incorporates controller hardware into the drive. IDE is offered in 8- and 16-bit interface types. Eight-bit drives are sometimes referred to as XT interface drives, and 16-bit drives are sometimes referred to as AT interface drives.
IDE drives do
not
use a SCSI bus. Apple computers continue to use an external SCSI chain, which is supported by a SCSI chip on the logic board.
Also, Apple’s HD SC Setup works with IDE drives.
Basics WIDE and FAST SCSI Protocols - 2
WIDE and FAST SCSI Protocols
SCSI chains that use SCSI-2 protocols are faster than SCSI chains using the original SCSI protocols. Two terms used in the SCSI-2 protocol are “WIDE” and “FAST.”
The term “WIDE” defines the 2-byte or 4-byte wide data interface where each data byte uses its corresponding parity bit. The traditional SCSI-1 interface protocol is 1 byte wide. “FAST” SCSI is defined as data transfer rates between 5 MHz and 10 MHz.
Check these protocols against individual drives for comparative data.
Devices using the SCSI-2 WIDE and FAST protocols are compatible with existing SCSI-1 devices.
Troubleshooting General/ - 1
General
The Symptom Charts included in this chapter will help you diagnose specific symptoms related to your product. Because cures are listed on the charts in the order of most likely solution, try the first cure first. Verify whether or not the product continues to exhibit the symptom. If the symptom persists, try the next cure. (Note: If you have replaced a module, reinstall the original module before you proceed to the next cure.)
If you are not sure what the problem is, or if the Symptom Charts do not resolve the problem, refer to the Flowchart for the product family.
For additional assistance, contact Apple Technical Support.
Troubleshooting HD SC Setup/ - 2
HD SC Setup
Before you replace any drive hardware, run HD SC Setup to update the driver on the drive.
HD SC Setup works with SCSI and IDE drives.
Upgrades Drives in Quadra 900/950 - 1
Drives in Quadra 900/950
There are three general procedures for preparing hard drives for Quadra 900/950 computers: • Removing the hard drive
mechanism from the carrier.
• Removing resistors from the replacement drives.
• Connecting the SCSI select cable.
Hard Drive Carrier
Hard Drive Mechanism
Termination Resistors
SCSI SelectCable
SCSI Select Switch
Upgrades Drives in Quadra 900/950 - 2
Removing the Hard Drive
1 Disconnect the SCSI select cable from the hard drive.
2 Remove the four Phillips screws.
3 Slide the drive out of the carrier.
SCSISelectCable
Drive Carrier
Hard Drive
Upgrades Drives in Quadra 900/950 - 3
Removing Resistors from the 160 MB Hard Drive
Caution
: Failure to remove the terminator resistors can damage the logic board.
1 Pull up on the tab and remove the resistors from a replacement 160 MB hard drive.
2 Insert the drive in the customer’s carrier and install four screws.
3 Attach the SCSI select cable tab-up as shown.
SCSISelectCable
TerminatorResistors
Tab
Tab
Upgrades Drives in Quadra 900/950 - 4
Removing Resistors from the 230 MB Hard Drive
Caution:
Failure to remove the terminator resistors can damage the logic board.
1 Using needlenose pliers, remove the resistors from a replacement 230 MB drive.
2 Insert the drive in the customer’s carrier and install four screws.
3 Attach the SCSI select cable as shown.
Hard Drive
SCSI SelectCable
Tab
TerminatorResistors
Upgrades Drives in Quadra 900/950 - 5
Removing Resistors from the 400 MB Hard Drive
Caution:
Failure to remove the terminator resistors can damage the logic board.
1 Remove the resistors from a replacement 400 MB drive.
2 Insert the drive in the customer’s carrier and install four screws.
3 Attach the SCSI select cable with the tab of its connector facing down.
TerminatorResistors
Hard Drive
SCSI SelectCable
Upgrades Identifying 20SC Rev A & B - 6
Identifying 20SC Rev A & B
No preliminary steps are required before you begin this procedure.
Note:
The Hard Drive 20SC 3.5-inch Revision A and Revision B drives must be replaced like-for-like.
Identify the revision you need by matching the customer’s defective drive with the replacement drive.
Upgrades Identifying 20SC Rev A & B - 7
• Revision A replacement drives ship in an internal carrier, component side up.
• Revision B replacement drives ship in an internal carrier, component side down.
Revision A (661-0373)
Revision B (661-0612)
Additional Procedures Carrier Removal - 1
Carrier Removal
No preliminary steps are required.
Note:
This procedure applies to hard drive mechanisms that have been removed from a computer or an external hard drive, or to replacement drive mechanisms that have not yet been installed in the computer.
Caution:
Review the ESD precautions in Bulletins/Safety.
Additional Procedures Carrier Removal - 2
Ê
Remove the four screws and lift the carrier from the hard drive.
Replacement Caution:
Be sure to properly torque the replacement drive to its carrier. Failure to do so could damage the drive. See “Torque Sequence” in this chapter.
Note:
For information on returning defective drives, see “General Return Info” and refer to the Parts chapter in this manual.
Drive Carrier
HardDrive
Additional Procedures Torque Sequence - 3
Torque Sequence
No preliminary steps are required before you begin this procedure.
Note
: This procedure applies to hard drive mechanisms that have been removed from a computer or an external hard drive, or to replacement drive mechanisms that have not yet been installed in the computer.
Using a torque driver,
Torque Driver
HardDrive
DriveCarrier
Additional Procedures Torque Sequence - 4
tighten the screws in the order shown. Torque the screws with driver to 8.0-inch pounds.
Note:
The torque sequence is the same for all types of drives and carriers. The Apple torque driver is preset to 8 in/lbs.
Additional Procedures Modifying 5.25-Inch Drives - 5
Modifying 5.25-Inch Drives
No preliminary steps are required before you begin this procedure.
This section describes procedures for modifying 5.25-inch replacement hard drives that are qualified for external hard drives. To learn whether a replacement drive is a qualified external drive, refer to compatibility information in the Service Source parts database.
External Hard Drives
Only
Additional Procedures Modifying 5.25-Inch Drives - 6
Note:
The 20 MB and160 MB external 5.25-inch replacement hard drives ship prepared for external drives. You must modify other replacement hard drives for use in external hard drives.
Ê
Additional Procedures Modifying 5.25-Inch Drives - 7
1 Remove the four mounting screws and carrier from the 5.25-inch service replacement hard drive.
2 Disconnect the power cable (if attached) from the replacement drive.
Ê
Power Cable
Carrier
Additional Procedures Modifying 5.25-Inch Drives - 8
3 Disconnect the resistors from the component side of the replacement drive. Use needlenose pliers and pull the resistors straight up.
4
Replacement Note:
Be sure that the tab on the SCSI select cable connector points toward the hard drive data cable.
Connect the SCSI select cable to the three pairs of pins on the component side of the drive. Leave the black jumpers on the other pins.
TerminatorResistors
SCSI Select Cable
Jumpers
Additional Procedures Modifying 5.25-Inch Drives - 9
5 Connect the LED cable connector from the customer’s external carrier to the component side of the replacement drive.
6 Attach the reconfigured replacement hard drive to the customer’s external carrier with the four screws.
Note:
For information on returning defective drives, see “General Return Info” and refer to the Service Source parts database.
LEDCable
Additional Procedures Modifying 3.5-Inch Drives - 10
Modifying 3.5-Inch Drives
No preliminary steps are required before you begin this procedure.
This section describes procedures for modifying 3.5-inch replacement hard drives that are qualified for external hard drives. To learn whether a replacement drive is a qualified external drive, refer to compatibility information in the Service Source parts database.
External Drives Only
Additional Procedures Modifying 3.5-Inch Drives - 11
Note:
The External 20 MB SCSI Rev A replacement hard drive ships prepared for use in external hard drives. You must modify other replacement hard drives for use in external hard drives.
Ê
Additional Procedures Modifying 3.5-Inch Drives - 12
1 Remove the 3.5-inch replacement hard drive from its carrier.
2 Disconnect the power cable (if attached) from the replacement drive.
3
Note:
The location of the terminator resistors may differ among drives.
Disconnect the three terminator resistors from the component side of the replacement drive. Use needlenose pliers, if necessary.
Power Cable Terminator Resistors
Additional Procedures Modifying 3.5-Inch Drives - 13
4
Important:
You must connect the customer’s SCSI select cable to six unkeyed pins on the controller board. Be aware that SCSI select cable connectors differ among drives in both design and location.
For SCSI select cable connectors located on the edge of the drive controller board:• Remove any black
jumpers that may be installed on the outside pins.
Tab
SCSISelect Cable
SCSISelect Cable
Tab
Additional Procedures Modifying 3.5-Inch Drives - 14
• Face the tab up and attach the SCSI cable connector.
For SCSI select cable connectors located on the surface of the controller board:• Face the SCSI cable
connector tab toward the center of the drive.
• Attach the connector to the six pins closest to the 50-pin SCSI connector.
Important:
Combinations of SCSI select connectors and cables vary. To verify the proper position of the
SCSISelectCable
Tab
Additional Procedures Modifying 3.5-Inch Drives - 15
SCSI select cable connector, connect the drive to a known-good Macintosh and choose
Get Info
from the Finder’s File menu. If
Get Info
displays the wrong SCSI ID or drive name, reverse the tab of the SCSI select cable connector.
Ê
Additional Procedures Modifying 3.5-Inch Drives - 16
5 Connect the LED cable connector from the customer’s external carrier to the component side of the replacement drive.
6 Install the reconfigured replacement hard drive in the customer’s external carrier.
Note:
For information on returning defective drives, see “General Return Info” and refer to the Service Source parts database.
Customer'sExternal Carrier
LEDCable
Additional Procedures General Return Information - 17
General Return Information
No preliminary steps are required before you begin this procedure.
Note
: You must return a defective hard drive to Apple without the carrier and cables.
Note:
For specific return requirements, refer to the Service Source parts database.
Ê
Additional Procedures General Return Information - 18
Each drive has four cables that need to be removed before the hard drive is returned. They are• Power cable• Hard drive data cable• SCSI select switch cable• LED cable
Note:
For specific return requirements, refer to the Service Source parts database.
LED CableSCSI Select Cable
Hard Drive Data Cable
Power Cable
Additional Procedures Setting SCSI ID - 19
Setting SCSI ID
No preliminary steps are required before you begin this procedure.
1 To set the SCSI ID, locate the drive’s six SCSI select pins.
Note:
The location of the SCSI select pins varies among drives. Generally, the group of six (occasionally eight) pins is on the top or side of the printed circuit board.
SCSI Select Pins
Additional Procedures Setting SCSI ID - 20
Note:
If you are installing the drive in a docking station, such as the DuoDock, Apple recommends you change the SCSI ID to 1. If you are installing the drive mechanism in an external drive case, Apple recommends you change the SCSI ID to any number from 2 to 6.
Ê
Additional Procedures Setting SCSI ID - 21
2 Place jumpers on the pairs of pins as shown in the table below.
Note
: In the following table, the SCSI ID numbers are labeled across the top and the pin numbers are labeled on the side. (The pin pairs may be labeled using either the A0-A1-A2 pin number convention or the E1-E2-E3 convention. Some pin pairs may not be labeled.) The letter “J”
Additional Procedures Setting SCSI ID - 22
indicates a jumper.
0 1 2 3 4 5 6 7
A0/E1 - J - J - J - J
A0/E2 - - J J - - J J
A0/E3 - - - - J J J J
Parts 11
Cable, Hard Drive, LED, Amber (Fits 1’’ Height Drives) 922-0003
CompatibilityThis cable can be used with the following drives:• Quantum ProDrive LPS• Quantum ProDrive ELS
Parts 12
Cable, Hard Drive, LED, Amber (Replaced by 922-1245) 590-0506
CompatibilityThis cable can be used with the following drives:• All 1.6” high 3.5” drives, Quantum ProDrive, Miniscribe, Rodine• All Conner drives
Parts 13
Cable, Hard Drive, LED, Amber 922-1245
CompatibilityThis cable can be used with the following drives:• All 1.6” high 3.5” drives, Quantum ProDrive, Miniscribe, Rodine• All Conner drives
Parts 14
Cable, LED (400 MB HDA) (replaced by 922-1244) 590-0248
CompatibilityThis cable can be used with the following drives:• Seagate 400 MB
Parts 15
Cable, LED (400 MB HDA) 922-1244
CompatibilityThis cable can be used with the following drives:• Seagate 400 MB
Parts 16
Cable, LED (Red) (Replaced by 922-1243) 590-0237
CompatibilityThis cable can be used with the following drives:• All 1.6” high 3.5” drives, Quantum ProDrive, Miniscribe, Rodine• All Conner drives
Parts 17
Cable, LED (Yellow) 922-1243
CompatibilityThis cable can be used with the following drives:• All 1.6” high 3.5” drives, Quantum ProDrive, Miniscribe, Rodine• All Conner drives
Parts 21
Cable, Power, HDA/CD-ROM 922-0051
This power cable is used with the Power Macintosh 7100/66 and 7100/66AV models. It is NOT compatible with the 7100/80 and 7100/80AV models.
Parts 24
Cable, SCSI Device Select (replaced by 922-1247) 590-0518
CompatibilityThis cable can be used with the following drives:• All 1.6” high 3.5” drives, including 160 MB IBM and Seagate 400 MB• Quantum ProDrive LPS 40 MB, 80 MB
Parts 25
Cable, SCSI Select, 230/500 MB HDA’s (Replaced by 922-1248) 590-0794
CompatibilityThis cable can be used with the following drives:• Seagate 500 MB, 1 GB• Quantum ProDrive LPS 80 MB, 160 MB, 230 MB• Quantum ProDrive ELS 40 MB, 80 MB, 120 MB, 160 MB, 320 MB• All 1” high 3.5” IBM drives• All 1” high 3.5” Conner drives
Parts 26
Cable, SCSI Select, 230/500 MB HDA’S 922-1248
CompatibilityThis cable can be used with the following drives:• Seagate 500 MB, 1 GB• Quantum ProDrive LPS 80 MB, 160 MB, 230 MB• Quantum ProDrive ELS 40 MB, 80 MB, 120 MB, 160 MB, 320 MB• All 1” high 3.5” IBM drives• All 1” high 3.5” Conner drives
Parts 27
Cable, SCSI Select, 400 MB HDA (Replaced by 922-1247) 590-0790
CompatibilityThis cable can be used with the following drives:• All 1.6” high 3.5” drives, including 160 MB IBM and Seagate 400 MB• Quantum ProDrive LPS 40 MB, 80 MB
Parts 28
Cable, SCSI Select, 400 MB HDA 922-1247
CompatibilityThis cable can be used with the following drives:• All 1.6” high 3.5” drives, including 160 MB IBM and Seagate 400 MB• Quantum ProDrive LPS 40 MB, 80 MB
Parts 29
Cable, SCSI Select 590-0238
CompatibilityThis cable can be used with the following drives:• All 1.6” high 3.5” drives, including 160 MB IBM and Seagate 400 MB• Quantum ProDrive LPS 40 MB, 80 MB
Parts 30
Cable, SCSI Select 922-1207
CompatibilityThis cable can be used with the following drives:• Conner FilePro 3, CFA Series
Parts 40
CD/HD Connector, Adapter’ 922-1820
Part number 922-1820 connects hard drives to the LC 500 series chassis/harness assembly.Part number 922-1820 also connects the caddyless CD ROM drive to the chassis/harness assembly of the LC 575.
Part number 922-1820 is not interchangeable with part number 922-1821 used to connect the 300i CD ROM drive to the LC 520 harness/chassis assembly.
Parts 51
Hard Drive, 1 GB, SCSI, 3.5" 661-0228
This drive is one of the recommended replacement choices for an out-of-warranty hard drive that’s been discontinued. This drive may not be exchanged for the failed, out-of-warranty drive, but must be ordered as stock.
All replacement drives will be shipped without carriers. Return the defective drive without cables, carrier, hard drive frame, LED cable, or SCSI select cable. Special Packaging Requirements: Pkg: #602-0282 Surcharge: $150.00.
Failure to comply with these requirements may result in a packaging noncompliance surcharge. The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity or EPROM
Parts 52
label, or labels that say “Warranty Void if Seal Broken” have been tampered with or removed.
Parts 53
Hard Drive, 1.1 GB, IDE, 2.5" 661-0944
The hard drive ships without a carrier.
When present, the following must be removed before returning the drive to Apple: frame, LED cable, SCSI select cable.
WARRANTY: The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity and EPROM label, or labels that say “Warranty Void If Seal Is Broken” have been tampered with or removed.
For maximum compatibility, Apple recommends this drive for use in older Macintosh computers and external drives that support 2.5" IDE drives.
Parts 54
APPLE REQUIRES SPECIAL PACKAGING: failure to comply with these requirements may result in a packaging noncompliance charge. For more information, select the notes icon in the Illustrated Parts chapter of the Hard Drives manual.
Parts 55
Hard Drive, 1.2 GB, IDE, 3.5" 661-1106
When present, the following must be removed before returning the drive to Apple: frame, LED cable, SCSI select cable.
WARRANTY: The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity or EPROM label, or labels that say “Warranty Void If Seal Is Broken” have been tampered with or removed.
APPLE REQUIRES SPECIAL PACKAGING; failure to comply with these requirements may result in a packaging noncompliance charge.
Conner Drive Model # CFS1275AQuantum Drive Model # 1.2GB FRBLA
Parts 57
Hard Drive, 1.2 GB, IDE, 3.5" 661-1139
When present, the following must be removed before returning the drive toApple: frame, LED cable, SCSI select cable.
WARRANTY: The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity or EPROM label, or labels that say “Warranty Void If Seal Is Broken” have been tampered with or removed.
The IDE drive is distinguished from a SCSI drive by the third (alternate power) connector built into the connector bar on the PCB.
APPLE REQUIRES SPECIAL PACKAGING; failure to comply with these requirements may result in a packaging
Parts 58
noncompliance charge.
Conner Drive Model # CFS1275AQuantum Drive Model # 1.2GB FRBLASeagate Drive model # ST31276AQuantum Drive Model # 1.2GB FBTMA
Parts 59
Hard Drive, 1.2 GB, SCSI, 3.5" 661-1142
Warranty: The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity and EPROM label, or labels that say “Warranty Void if Seal is Broken” have been tampered with or removed.
APPLE REQUIRES SPECIAL PACKAGING; failure to comply with these requirements may result in a packaging noncompliance charge. When present, the following must be removed before returning the drive to Apple: Frame, LED cable, SCSI select cable.
Parts 60
Hard Drive, 120 MB, SCSI, 2.5" (Discontinued) 661-0772
This part has been discontinued. For replacement of parts covered under warranty or AppleCare, order 661-1752. For replacement of out-of-warranty parts, refer to the list of available hard drives in this manual.
Carrier Return Requirements:Return the defective drive without a carrier.
Cable Return Requirements:Return the defective drive without cables.
Special Packaging is Required.Pkg: 602-0307; Surcharge: $150.00Failure to comply with these requirements may result in a packaging noncompliance charge. Refer to Service Prices for ordering and pricing information.
Parts 61
Hard Drive, 120 MB, SCSI, 3.5 (Discontinued) 661-0021
This part has been discontinued. For replacement of parts covered under warranty or AppleCare®, order 661-1750. For replacement of out-of-warranty parts, refer to the parts list in the Service Source manual for the product you are repairing.
Parts 62
Hard Drive, 160 MB, SCSI, 2.5" (Discontinued) 661-0213
This part has been discontinued. For replacement of parts covered under warranty or AppleCare, order 661-1752. For replacement of out-of-warranty parts, refer to the list of available hard drives in this manual.
You may require a new mounting bracket if you are replacing a 661-0213.
Cable and Carrier Return RequirementsReturn the defective drive without a carrier or cables.
Special Packaging RequirementsPkg: 602-0307; Surcharge: $150.00Failure to comply with these requirements may result in a packaging noncompliance charge. Refer to Service Prices for ordering and pricing information.
Parts 63
Hard Drive, 160 MB, SCSI, 3.5" (Discontinued)661-0214
This part has been discontinued. For replacement of parts covered under warranty or AppleCare®, order 661-1750. For replacement of out-of-warranty parts, refer to the parts list in the Service Source manual for the product you are repairing.
Parts 64
Hard Drive, 160 MB, SCSI, 3.5" (Discontinued) 661-1649
This part has been discontinued. For replacement of parts covered under warranty or AppleCare®, order 661-1750. For replacement of out-of-warranty parts, refer to the parts list in the Service Source manual for the product you are repairing.
Parts 65
Hard Drive, 160 MB, SCSI, 3.5" w/A/UX v2.0.1 (Discontinued) 661-1639
This part has been discontinued. For replacement of a hard drive covered under warranty or AppleCare®, order 661-1750. For replacement of out-of-warranty hard drives, refer to the parts list in the Service Source manual for the product being repaired. In either case, you must also order the A/UX 2.0.1 Install CD (600-4193) to configure the replacement drive, as it will not come preconfigured.
Note: All replacement drives will be shipped without carriers.
Cable Return Requirements: Return the defective drive without cables.
Carrier Return Requirements: Return the defective drive without a carrier.
Parts 66
Special Packaging Requirements. Pkg: #602-0282. Surcharge: $150.00.
Failure to comply with these requirements may result in a packaging noncompliance surcharge. Please refer to Service Prices for ordering and pricing information.
The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity and EPROM label, or labels that say “Warranty Void If Seal Is Broken” have been tampered with or removed.
Parts 67
Hard Drive, 2 GB, Fast/Wide SCSI, 3.5’’, IBM661-0956
Return the defective hard drive without the SCSI cables, SCSI select cable, LED cable, power cable, and the drive carrier.
Warranty: The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity or EPROM label, or labels that say “War-ranty Void if Seal Broken” have been tampered with or removed. APPLE REQUIRES SPECIAL PACKAGING; failure to comply with these requirements may result in a packaging noncompliance charge.
This drive uses SCSI ID cable, Type 1, P/N 922-2102.
Parts 68
Hard Drive, 2 GB, SCSI, 3.5’’ 661-0180
This drive should only be exchanged “like-for-like.” This drive is NOT interchangeable with part number 661-0892 (HDA, 2 GB, 3.5’’ SCSI, Unhoused).
Return the hard drive without the HDA frame, LED cable, and SCSI select cable. Warranty: The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity or EPROM label, or labels that say “Warranty Void if Seal Broken” have been tampered with or removed. APPLE REQUIRES SPECIAL PACKAGING; failure to comply with these requirements may result in a packaging noncompliance charge.
Parts 69
Hard Drive, 2 GB, SCSI, 3.5’’ 661-0892
This drive should be exchanged only “like-for-like” and is NOT interchangeable with part number 661-0180 (Hard drive, 2 GB, SCSI, 3.5’’, Unhoused). WARRANTY: The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity and EPROM label, or labels that say “Warranty Void If Seal Is Broken” have been tampered with or removed.
When present, the following must be removed before returning the drive to Apple: frame, LED cable, SCSI select cable. APPLE REQUIRES SPECIAL PACKAGING: failure to comply with these requirements may result in a packaging noncompliance charge.
Parts 70
Hard Drive, 2 GB, SCSI, 3.5’’ 661-1076
This drive should only be exchanged “like-for-like.” This drive is NOT interchangeable with part number 661-0180.
Return the hard drive without the HDA frame, LED cable, and SCSI select cable. Warranty: The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity or EPROM label, or labels that say “Warranty Void if Seal Broken” have been tampered with or removed. APPLE REQUIRES SPECIAL PACKAGING; failure to comply with these requirements may result in a packaging noncompliance charge.
Parts 71
Hard Drive, 200 MB, SCSI, 2.5’’ 661-0779
When present, the following must be removed before returning the drive to Apple: frame, LED cable, SCSI select cable.
WARRANTY: The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity and EPROM label, or labels that say “Warranty Void If Seal Is Broken” have been tampered with or removed.
For maximum compatibility, Apple recommends this drive for use in older Macintosh computers and external drives that support 2.5" SCSI drives.
APPLE REQUIRES SPECIAL PACKAGING: failure to comply
Parts 73
Hard Drive, 230 MB, SCSI, 3.5" (Discontinued)661-1637
This part has been discontinued. For replacement of parts covered under warranty or AppleCare®, order 661-1750. For replacement of out-of-warranty parts, refer to the parts list in the Service Source manual for the product you are repairing.
Parts 74
Hard Drive, 240 MB, SCSI, 2.5’’ 661-0217
Note: All replacement drives will be shipped without carriers.
CompatibilityThis drive can be used in the following:•PowerBook Duo 210, 230, 250, 270c, 280, 280c•PowerBook 520, 520c, 540, 540c
Cable Return RequirementsReturn the defective drive without cables.
Carrier Return RequirementsReturn the defective drive without a carrier.
Special Packaging RequirementsPkg: 602-0307
Parts 75
Surcharge: $150.00Failure to comply with these requirements may result in a packaging noncompliance charge.
Refer to Service Prices for ordering and pricing information.
Parts 77
Hard Drive, 250 MB, IDE, 3.5" 661-0070
WARRANTY: The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity or EPROM label, or labels that say “Warranty Void If Seal Is Broken” have been tampered with or removed.
APPLE REQUIRES SPECIAL PACKAGING; failure to comply with these requirements may result in a packaging noncompliance charge.
Parts 78
Hard Drive, 250 MB, SCSI, 3.5" 661-0890
This drive is one of the recommended replacement choices for an out-of-warranty hard drive that’s been discontinued. This drive may not be exchanged for the failed, out-of-warranty drive, but must be ordered as stock.
Parts 79
Hard Drive, 320 MB, SCSI, 2.5’’ 661-0896
When present, the following must be removed before returning the drive to Apple: frame, LED cable, SCSI select cable.
WARRANTY: The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity and EPROM label, or labels that say “Warranty Void If Seal Is Broken” have been tampered with or removed.
For maximum compatibility, Apple recommends this drive for use in older Macintosh computers and external drives that support 2.5" SCSI drives.
APPLE REQUIRES SPECIAL PACKAGING: failure to comply
Parts 81
Hard Drive, 320 MB, SCSI, 3.5’’ (replaced by 661-0182)661-0505
Cable Return Requirements:Return the defective drive without cables.
Carrier Return Requirements:Return the defective drive without a carrier.
Special Packaging Is Required.Pkg: #602-1018Surcharge: $150.00Failure to comply with these requirements may result in a packaging noncompliance surcharge. Please refer to Service Prices for ordering and pricing information.
Parts 82
Hard Drive, 320 MB, SCSI, 2.5", In-Warranty Exchange ONLY 661-1753
Only order this part number when exchanging a failed hard drive that meets both of the following conditions: 1) the failed hard drive is covered under warranty or AppleCare®, and 2) the like-for-like replacement hard drive has been discontinued.
Apple has made every effort to maintain LED support in its exchange program; however, some drives no longer support an LED. We regret any inconvenience this may cause.
Parts 83
Hard Drive, 350 MB, IDE, 3.5" 661-0068
When present, the following must be removed before returning the drive to Apple: frame, LED cable, SCSI select cable.
WARRANTY: The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity or EPROM label, or labels that say “Warranty Void If Seal Is Broken” have been tampered with or removed.
APPLE REQUIRES SPECIAL PACKAGING; failure to comply with these requirements may result in a packaging noncompliance charge.
Parts 84
Hard Drive, 350 MB, SCSI, 3.5" 661-0182
This drive is one of the recommended replacement choices for an out-of-warranty hard drive that’s been discontinued. This drive may not be exchanged for the failed, out-of-warranty drive, but must be ordered as stock.
Parts 85
Hard Drive, 4 GB, Fast/Wide SCSI, 3.5” 661-0958
Return the defective hard drive without the SCSI cables, SCSI select cable, LED cable, power cable, and the drive carrier.
Warranty: The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity or EPROM label, or labels that say “Warranty Void if Seal Broken” have been tampered with or removed. APPLE REQUIRES SPECIAL PACKAGING; failure to comply with these requirements may result in a packaging noncompliance charge.
This drive uses SCSI ID cable, Type 1, P/N 922-2102.
Parts 86
Hard Drive, 4 GB, SCSI, 3.5” 661-0951
When present, the following must be removed before returning the drive to Apple: frame, LED cable, SCSI select cable.
WARRANTY: The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity or EPROM label, or labels that say “Warranty Void If Seal Is Broken” have been tampered with or removed.
APPLE REQUIRES SPECIAL PACKAGING; failure to comply with these requirements may result in a packaging noncompliance charge.
Parts 87
Hard Drive, 40 MB, SCSI, 2.5", PB 100 (Discontinued) 661-1632
This part has been discontinued. For replacement of parts covered under warranty or AppleCare, order 661-1752. For replacement of out-of-warranty parts, refer to the list of available hard drives in this manual.
The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity and EPROM label, or labels that say “Warranty Void If Seal Is Broken” have been tampered with or removed.
Carrier Return Requirements:No carrier.
Special Packaging is Required.Pkg: #602-0307
Parts 88
Surcharge: $150.00Failure to comply with these requirements may result in a packaging noncompliance
surcharge. Please refer to Service Prices for ordering and pricing information.
Parts 89
Hard Drive, 40 MB, SCSI, 2.5", PB 100 (Discontinued)661-1644
This part has been discontinued. For replacement of parts covered under warranty or AppleCare, order 661-1752. For replacement of out-of-warranty parts, refer to the list of available hard drives in this manual.
The Conner 40 MB drive has a beveled edge on the left-hand side.
The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity and EPROM label, or labels that say “Warranty Void If Seal Is Broken” have been tampered with or removed.
Cable Return Requirements:Return the defective drive without cables.
Parts 90
Carrier Return Requirements:
Return the defective drive without a carrier.
Special Packaging is Required.Pkg: #602-0307Surcharge: $150.00Failure to comply with these requirements may result in a packaging noncompliance surcharge. Please refer to Service Prices for ordering and pricing information.
Parts 91
Hard Drive, 40 MB, SCSI, 2.5" (Discontinued)661-0016
This part has been discontinued. For replacement of parts covered under warranty or AppleCare, order 661-1752. For replacement of out-of-warranty parts, refer to the list of available hard drives in this manual.
Parts 92
Hard Drive, 40 MB, SCSI, 2.5" (Discontinued) 661-1630
This part has been discontinued. For replacement of parts covered under warranty or AppleCare, order 661-1752. For replacement of out-of-warranty parts, refer to other list of available hard drives in this manual.
This drive contains a plastic “horse-shoe” shaped cover located on the top of the drive.
The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity and EPROM label, or labels that say “Warranty Void If Seal Is Broken” have been tampered with or removed.
Cable Return Requirements:Return the defective drive without cables.
Parts 93
Carrier Return Requirements:
Return the defective drive without a carrier.
Special Packaging is Required.Pkg: #602-0307Surcharge: $150.00Failure to comply with these requirements may result in a packaging noncompliance surcharge. Please refer to Service Prices for ordering and pricing information.
Parts 94
Hard Drive, 40 MB, SCSI, 3.5’’661-0216
Upon failure all 20 MB drives will be upgraded to 40 MB drives. If you send in a 20 MB drive, you will receive a 40 MB replacement drive.
Note: All replacement drives will be shipped without carriers.
CompatibilityThis drive can be used in the following:•Macintosh SE, SE/30•Macintosh II, IIcx, IIci, IIx, IIfx•Macintosh IIsi•Classic, Classic II•Color Classic, Color Classic II•LC, LC II, LC III•Performa 400
Parts 95
Cable Return Requirements
Return the defective drive without cables.
Carrier Return RequirementsReturn the drive without a carrier.
Special Packaging RequirementsPkg: #602-0282Surcharge: $150.00Failure to comply with these requirements may result in a packaging noncompliance surcharge. Please refer to Service Prices for ordering and pricing information.
Parts 96
Hard Drive, 400 MB, SCSI, 3.5 ‘’ (replaced by 661-0219661-1636
When present, the following must be removed before returning the drive to Apple: frame, LED cable, SCSI select cable.
WARRANTY: The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity and EPROM label, or labels that say “Warranty Void If Seal Is Broken” have been tampered with or removed.
APPLE REQUIRES SPECIAL PACKAGING: failure to comply with these requirements may result in a packaging noncompliance charge. When present, the following must be removed before returning the drive to
Parts 98
Hard Drive, 500 MB, IDE, 2.5 ‘’ 661-1058
When present, the following must be removed before returning the drive to Apple: frame, and LED cable.
This drive may or may not have an Apple logo on it.
WARRANTY: The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity and EPROM label, or labels that say “Warranty Void If Seal Is Broken” have been tampered with or removed.
For maximum compatibility, Apple recommends this drive for use in older Macintosh computers and external drives that support 2.5" IDE drives.
Parts 99
APPLE REQUIRES SPECIAL PACKAGING: failure to comply with these requirements may result in a packaging noncompliance charge.
Parts 100
Hard Drive, 500 MB, IDE, 2.5 ‘’ 661-0047
When present, the following must be removed before returning the drive to Apple: frame, LED cable, SCSI select cable.
WARRANTY: The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity and EPROM label, or labels that say “Warranty Void If Seal Is Broken” have been tampered with or removed.
For maximum compatibility, Apple recommends this drive for use in older Macintosh computers and external drives that support 2.5" IDE drives.
APPLE REQUIRES SPECIAL PACKAGING: failure to comply
Parts 101
with these requirements may result in a packaging noncompliance charge. For more information, select the notes icon in the Illustrated Parts chapter of the Hard Drives manual.
Parts 102
Hard Drive, 500 MB, IDE, 2.5", In-Warranty Exchange ONLY 661-1751
Only order this part number when exchanging a failed hard drive that meets both of the following conditions: 1) the failed hard drive is covered under warranty or AppleCare®, and 2) the like-for-like replacement hard drive has been discontinued.
Apple has made every effort to maintain LED support in its exchange program; however, some drives no longer support an LED. We regret any inconvenience this may cause.
Parts 103
Hard Drive, 500 MB, SCSI, 2.5 ‘’ 661-0175
When present, the following must be removed before returning the drive to Apple: frame, LED cable, SCSI select cable.
WARRANTY: The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity or EPROM label, or labels that say “Warranty Void If Seal Is Broken” have been tampered with or removed.
For maximum compatibility, Apple recommends this drive for use in older Macintosh computers and external drives that support 2.5" SCSI drives.
APPLE REQUIRES SPECIAL PACKAGING; failure to comply with these requirements may result in a packaging
Parts 105
Hard Drive, 500 MB, SCSI, 2.5", In-Warranty Exchange ONLY 661-1752(Discontinued)
Failed 500 MB drives may be exchanged using 661-0175.
Parts 106
Hard Drive, 500 MB, IDE, 3.5" 661-0146
When present, the following must be removed before returning the drive to Apple: frame, LED cable, SCSI select cable.
WARRANTY: The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity and EPROM label, or labels that say “Warranty Void If Seal Is Broken” have been tampered with or removed.
APPLE REQUIRES SPECIAL PACKAGING: failure to comply with these requirements may result in a packaging noncompliance charge.
Parts 108
Hard Drive, 500 MB, SCSI, 3.5" 661-0219
This drive is one of the recommended replacement choices for an out-of-warranty hard drive that’s been discontinued. This drive may not be exchanged for the failed, out-of-warranty drive, but must be ordered as stock. All replacement drives will be shipped without carriers.
Cable Return Requirements: Return the defective drive without cables.Carrier Return Requirements: Return the drive without a carr ier.Special Packaging Requirements: Pkg: #602-0282 Surcharge: $150.00Failure to comply with these requirements may result in a packaging noncompliance surcharge. Please refer to Service Price Pages for ordering and pricing information.
Parts 109
Hard Drive, 500 MB, SCSI, 3.5" 661-0974
This drive is one of the recommended replacement choices for an out-of-warranty hard drive that’s been discontinued. This drive may not be exchanged for the failed, out-of-warranty drive, but must be ordered as stock.
Parts 110
Hard Drive, 500 MB, SCSI, 3.5", In-Warranty Exchange Only 661-1750
Only order this part number when exchanging a failed hard drive that meets both of the following conditions: 1) the failed hard drive is covered under warranty or AppleCare®, and 2) the like-for-like replacement hard drive has been discontinued.
Apple has made every effort to maintain LED support in its exchange program; however, some drives no longer support an LED. We regret any inconvenience this may cause.
Parts 112
Hard Drive, 700 MB, SCSI, 3.5’’ 661-0184
When present, the following must be removed before returning the drive to Apple: frame, LED cable, SCSI select cable.
WARRANTY: The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity and EPROM label, or labels that say “Warranty Void If Seal Is Broken” have been tampered with or removed.
APPLE REQUIRES SPECIAL PACKAGING: failure to comply with these requirements may result in a packaging noncompliance charge.
Parts 113
Hard Drive, 750 MB, IDE, 2.5’’ 661-0957
WARRANTY: The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity or EPROM label, or labels that say “Warranty Void If Seal Is Broken” have been tampered with or removed.
For maximum compatibility, Apple recommends this drive for use in older Macintosh computers and external drives which support 2.5" IDE.
APPLE REQUIRES SPECIAL PACKAGING; failure to comply with these requirements may result in a packaging noncompliance charge. For more information, select the notes icon in the Illustrated Parts chapter of the Hard Drives manual.W
Parts 114
Hard Drive, 750 MB, SCSI, 2.5’’ 661-0943
When present, the following must be removed before returning the drive to Apple: frame, LED cable, SCSI select cable.
WARRANTY: The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity and EPROM label, or labels that say “Warranty Void If Seal Is Broken” have been tampered with or removed.
APPLE REQUIRES SPECIAL PACKAGING: failure to comply with these requirements may result in a packaging noncompliance charge. For more information, select the notes icon in the Illustrated Parts chapter of the Hard Drives manual.
Parts 115
Hard Drive, 80 MB, SCSI, 2.5" (Discontinued) 661-0211
This part has been discontinued. For replacement of parts covered under warranty or AppleCare, order 661-1752. For replacement of out-of-warranty parts, refer to the list of available hard drives in this manual.
Note: All replacement drives will be shipped without carriers
Cable Return RequirementsReturn the defective drive without cables.
Carrier Return RequirementsReturn the defective drive without a carrier.
Special Packaging RequirementsPkg: 602-0307
Parts 116
Surcharge: $150.00Failure to comply with these requirements may result in a packaging noncompliance charge. Refer to Service Prices for ordering and pricing information.
Parts 117
Hard Drive, 80 MB, SCSI, 3.5" (Discontinued) 661-0111
This part has been discontinued. For replacement of parts covered under warranty or AppleCare®, order 661-1750. For replacement of out-of-warranty parts, refer to the parts list in the Service Source manual for the product you are repairing.
Parts 118
Hard Drive, 80 MB, SCSI, 3.5" (Discontinued) 661-0212
This part has been discontinued. For replacement of parts covered under warranty or AppleCare®, order 661-1750. For replacement of out-of-warranty parts, refer to the parts list in the Service Source manual for the product you are repairing.
Parts 119
Hard Drive, 800 MB, IDE, 3.5" 661-0999
WARRANTY: The drive warranty will be void and Apple will return the module to the service provider without repair if the drive bar code label, manufacturer identification label, Apple capacity or EPROM label, or labels that say “Warranty Void If Seal Is Broken” have been tampered with or removed.
APPLE REQUIRES SPECIAL PACKAGING; failure to comply with these requirements may result in a packaging noncompliance charge.
Parts 120
Hard Drive, 800 MB, SCSI, 3.5" 661-1102
This drive is one of the recommended replacement choices for an out-of-warranty hard drive that’s been discontinued. This drive may not be exchanged for the failed, out-of-warranty drive, but must be ordered as stock.
Parts 121
Hard Drive, 80 MB, SCSI, 3.5", A/UX v.2.0 (Discontinued) 661-0613
This part has been discontinued. For replacement of a hard drive covered under warranty or AppleCare®, order 661-1750. For replacement of out-of-warranty hard drives, refer to the parts list in the Service Source manual for the product being repaired. In either case, you must also order the A/UX 2.0 Install CD (600-4192) to configure the replacement drive, as it will not come preconfigured.
Note: All replacement drives will be shipped without carriers.
Cable Return Requirements: Return the defective drive without cables.
Carrier Return Requirements: Return the defective drive without a carrier.
Parts 122
Special Packaging Requirements: Pkg: #602-0282. Surcharge: $150.00Failure to comply with these requirements may result in a packaging noncompliance surcharge. Please refer to Service Prices for ordering and pricing information.
Parts 134
Switch, SCSI Select Assembly 922-1250
CompatibilityThis switch can be used with the following cables:• 9 2 2 - 1 2 4 7• 9 2 2 - 1 2 4 8• 9 2 2 - 1 2 0 7